www.wharfedalepro.com
Titan™
Titan™ 8 Passive Titan™ 12 Passive Titan™ 15 PassiveTitan™ 8 Active MKII Titan™ 12D Titan™ 15D Titan™ Sub A12 Titan™ Sub A15
OPERATING MANUAL AND USER GUIDE
OPERATING MANUAL AND USER GUIDE
1
IMPORTANT WARNINGS & SAFETY INSTRUCTIONS1. Readtheseinstructions2. Followallinstructions3. Keeptheseinstructions4. Heedallwarnings5. Donotusethisapparatusnearwater6. Cleanonlywithdrycloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.8. Donot install nearanyheatsourcessuchas radiators,heat registers, stoves,orother
apparatus (including amplifiers) that produce heat.9. Donotdefeatthesafetypurposeofthepolarisedorgroundingplug.Apolarisedplughastwo
bladeswithonewiderthantheother.Agroundingplughastwobladesandathirdgroundingprong.Thewidebladeorthethirdprongisprovidedforyoursafety.Iftheprovidedplugdoesnot fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protectthepowercordfrombeingwalkedonorpinchedparticularlyattheplugs,conveniencereceptacles,andatthepointwheretheyexitfromtheapparatus.
11. Only use attachments/accessories specified by the manufacturer.12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
theapparatus.Whenacartorrackisused,usecautionwhenmovingthecartandapparatuscombinationtoavoidinjuryfromtip-over.
13. Unplugtheapparatusduringlightningstormsorwhenunusedforlongperiodsoftime.14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been
damaged inanyway includingbutnot limited topowersupplycordorplugdamage, liquidingress,foreignobjectsinthechassis,exposuretorain/moistureorimpactdamage.Inadditiontheunitmustbeservicedwhenyouexperienceanyabnormaloperation.
15. CAUTION:Theseservicing instructionsare forusebyqualifiedservicepersonnelonly.Toreduce the riskofelectricshock,donotattempt toperformanyservicingother than thatcontained in the operating instructions unless you are qualified to do so. In addition opening the casingwillresultinyourwarrantybecomingnullandvoid.
16. Do not install this apparatus in a confined space such as a book case or similar unit. Good ventilationshouldbemaintainedaroundtheapparatusandanyvents,air-inletsorfansshouldnotbeobstructedbyobjectssuchaspaper,table-cloths,curtainsetc.
17. WARNING: To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture. The apparatus should not be exposed to dripping or splashing and objects filled with liquids,suchasvases,shouldnotbeplacedontheapparatus.
18. WARNING: The mains plug/appliance coupler is used as a disconnect device, the disconnect deviceshallremainreadilyoperable.
Titan™ Series
2
19. - This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the usertothepresenceofnon-insulated“dangerousvoltage”withintheproduct’senclosurethatmay be of sufficient magnitude to constitute a risk of electric shock.
- Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
-Theexclamationpointwithinanequilateral triangle is intended toalert theuser to thepresenceof importantoperatingandmaintenanceinstructions inthe literatureaccompanyingtheappliance.
20. (Protective earthing terminal) The apparatus should be connected to a mains socket outlet withaprotectiveearthingconnection.
21. CorrectDisposalof thisproduct.Thismarking indicates that thisproductshouldnotbedisposedwithotherhouseholdwastes throughout theEU.Topreventpossibleharmto theenvironmentorhumanhealth fromuncontrolledwastedisposal, recycle it responsibly topromotethesustainablereuseofmaterialresources.Toreturnyouruseddevice,pleaseuselocalreturnandcollectionsystemsorcontact theretailerwheretheproductwaspurchased.Theycantakethisproductforsafeenvironmentallyfriendlyrecycling.
ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
OPERATING MANUAL AND USER GUIDE
3
TABLE OF CONTENTS
1..........................................Important Warnings & Safety Instructions 2..........................................Important Safety Information Powered Products 4..........................................Introduction / About the Titan™ Series 4..........................................Titanseriesoverview5..........................................Features6..........................................Qubit 7..........................................Setting up / Speaker Placement 7..........................................Connections/Wiring-Passive8..........................................Rear Panel Layout - Passive 8..........................................ConnectionDiagram-Passive11..........................................Rear Panel Layout - Active14..........................................ConnectionDiagram-Active15..........................................Rear Panel Layout - Sub A1216..........................................Connection Diagram - Sub A1218..........................................Rear Panel Layout - Sub A1519..........................................Connection Diagram - Sub A15 21..........................................Specifications - Titan™ Passive22..........................................Specifications - Titan™ Active24..........................................Specifications - Titan™ Subwoofers25..........................................DimensionalDrawings-Titan™8/1226..........................................DimensionalDrawings-Titan™15/8AMKII27..........................................DimensionalDrawings-Titan™12D/15D28..........................................Dimensional Drawings - Titan™ Sub A12 / A1529…………………………..…Warranty
Titan™ Series
4
Wharfedale Pro Titan™ Series is the result of many years of experience in the use, design and manufacturingofprofessional loudspeakerproducts.We takegreatpride inengineeringandbuildingeveryWharfedaleProloudspeakerandwishtothankyouforentrustinguswithyoursound.
From the time Gilbert Briggs built his first loudspeaker in 1932, to the present, Wharfedale Loudspeakers have maintained the same standard of quality in components, workmanship and performance.Wharfedaleareoneofthefewpresentdaymanufacturersthatdesign,engineerandbuildallofourowntransducers.
Pleasetakeafewminutestoreadthismanualcompletelyinordertoensurethatyougetthemostout of your Titan™ Series Loudspeaker system.
INTRODUCTION
TITAN™ SERIES OVERVIEW
The Titan Series are powerful, accurate, high quality loudspeaker systems with low distortion thataredesignedtodeliveroustandingperformanceatacosteffectivepricepoint.AnEllipticalWave Guide (EWG) is perfectly matched to the custom designed HF drivers and provides smooth dispersioninboththehorizontalandverticalplanes.
The road tough,gas-assist injectionmouldedpolypropyleneenclosuresareultra lightweightand include rubberisedhandlesandcablemanagement tomakeTitan themostuser-friendlyportable speaker on the market. Threaded rigging points mean that Titan is equally suited to flown applications;acomprehensiverangeofWharfedaleProwallmountingoptionsarealsoavailableasoptionalextras.
Active models feature rear panel power LED’s and a throat mounted LED to make you aware of AC power supply from both the front and rear of the unit. Active models also feature a horn LED defeat switch for less obtrusive aesthetics in applications such as conferencing and A/V presentations. The BRO™ (Bass Response Optimizer) circuit on the 12D and 15D models helps counteract loss of bass at low levels, similar to a loudness switch on home HiFi amplifiers. In addition our "D" models feature Qubit™ 24-bit 192kHz DSP Processing.
OPERATING MANUAL AND USER GUIDE
5
FEATURES
♦2-wayfullrangeloudspeakers
♦ Low distortion, high power moisture proof woofers
♦HFcompressiondrivers
♦ 90° x 60° Elliptical Wave Guide (EWG)
♦DTF™DynamicThermalFilamentHFprotection
♦ Lightweight, high strength gas-assist injection moulded polypropylene enclosures
♦Ergonomicrubberisedhandles
♦ Integral lockable 35mm (1⅜”) pole mount socket
♦M6/M8riggingpoints
♦ Speakon™ and ¼” jack inputs
Titan Passive
♦ Bi-amplified full range loudspeakers
♦ Low distortion, high power moisture proof woofers
♦HFcompressiondrivers
♦ Qubit™ 24-bit 192kHz DSP processing
♦ Independent LF & HF adaptive dynamics and signal limiting
♦ Per channel volume controls (Master only on 8A MKII)
♦ 2 Band EQ
♦ 90° x 60° elliptical Wave Guide (EWG)
♦ BRO™ Bass Response Optimizer (12D & 15D only)
♦ Horn LED defeat switch
♦ Balanced XLR output for parallel wiring
♦ XLR / ¼” jack combo inputs
♦Mic/linelevelinputselector
♦ 2 mixable inputs (12D & 15D only)
♦ Stereo RCA inputs (12D & 15D only)
♦ Lightweight, high strength gas-assist injection moulded polypropylene enclosures
♦Ergonomicrubberizedhandles
♦ Integral lockable 35mm (1⅜”) pole mount socket
♦M6/M8riggingpoints
♦IECACreceptacle
Titan Active
Titan™ Series
6
♦ Low distortion, high power woofers
♦ 2x balanced XLR HPF outputs
♦ 2x summed XLR / ¼” jack combo inputs
♦ Built in signal limiting
♦ Adjustable crossover frequency (SUB 12A only)
♦-∞to +6dB trim control
♦0°/180°switch
♦Ergonomichandles
♦Polemountsocket
♦IECACreceptacle
Subwoofer
Qubit brings the power and precision of 24-bit 192kHz DSP processing to the next generation of WharfedaleProProducts.
With advanced multi-band dynamic processing and filtering Qubit helps fine tune your system to sound natural and open. Qubit processing optimises the loudspeaker to provide smooth digital crossoverpoints thatareperfectlyaligned.Protection isoffered in the formof true independentadaptive LF and HF signal limiting that helps protect against thermal damage and driver over excursion.
Qubit has an extended frequency response that goes way beyond the capabilities of our hearing, providinganextendedphaseresponsethatremains linear throughoutournaturalhearingrange.A Qubit equipped system can reproduce exceptionally natural and accurate transients due to its phasecharacteristicsandperfecttimealignment.
QUBIT™
OPERATING MANUAL AND USER GUIDE
7
SETTING UP
1. Ensure the speakers power switch is in the off position (Active models only)2. Set the level controls to minimum (Fully anticlockwise) (Active models only)3. Set the EQ controls to 0dB (Active models only)4. Select mic/line input (Active models only)5.Connectallsignalcables6. Connect the power cable (Active models only)7. Switch on source equipment, ensuring that the master level is at minimum8. Switch on the Titan Loudspeaker (Active models only)9. Raise the level control on the Titan (Active models only) or external amplifier10. If the limit LED illuminates lower the level control, if more level is required you will need more speakers. Occasional flashes are acceptable. (Active models only)11. When powering down your system ensure that the level control (Active models only) has been loweredtominimumbeforeswitchingoffthepower
ThewellbehaveddispersioncharacteristicsoftheTitanseriesmakespeakerplacementquickandsimple.
AswithallfullrangeloudspeakersitisrecommendedtoplaceaTitanabovetheheadleveloftheaudience,as thehumanbodycanabsorbahugeamountofhighfrequencyenergy.Placingtheloudspeakerenclosurehigherupalsohelpsimprovecoverageformoreevenlevelsoveragreateraudiencearea.
Tripodspeakerstands,polemounts,WallbracketsandrigginghardwarecanbeusedtoelevatetheTitanloudspeaker.Alwaysensurethatanyaccessoriesthatareusedarecapableofsafelyelevatingtheloudspeakerasincorrectriggingcanbedangerousandevenfatal.Pleaserefertotheimportantsafetywarningssectionformoreguidelinesonriggingandsuspending.
Alwaysplaceyourmicrophonesoutsidethecoverageofyourfrontofhousespeakerstoreducetheriskoffeedback.
SPEAKER PLACEMENT
Titan™ Series
8
Titan™ REAR PANEL LAYOUT
CONNECTION DIAGRAM #1
Titantwochannelsetup
OPERATING MANUAL AND USER GUIDE
9
CONNECTION DIAGRAM # 2
Titanmono frontofhouse+stagemonitorsetup
NOTE: This configuration represents a 4 ohm load to each output channel of the amplifier
Titan™ Series
CONNECTION DIAGRAM # 3
USING THE Titan WITH A PASSIVE SUBWOOFER
CONNECTION DIAGRAM # 4
USING THE Titan™ 8/12/15 IN A BI-AMP SYSTEM
10
OPERATING MANUAL AND USER GUIDE
Titan™ 8A MKII / Titan™ 12D / Titan™ 15D
The Loop / Mix Switch
The LOOP/MIX switch allows you to control the signal content going to the XLR OUTPUT jack. In the “LOOP”
mode, this switch routes the signal of INPUT B to the line level XLR OUTPUT jack, bypassing the EQ section
and volume control. When in the MIX mode, this switch routes the combined (or “mixed”) signals of both INPUT
A and INPUT B to the line level XLR OUTPUT jack. This signal can then be sent to additional powered speakers
orpoweredsubwoofers.
8A MKII - REAR PANEL FEATURES
11
Titan™ Series
Titan™ 12D/15D REAR PANEL LAYOUT
12
1
2
78
12
3
5
9
1110
6
13
14
4
OPERATING MANUAL AND USER GUIDE
TITAN™ 8A MKII/12D/15D REAR PANEL FEATURES1. Heat Sink: The heat sink allows for dissipation of heat built up from the amplifier via air cooling at the rear
of the enclosure. (Titan 8A MKII and 15D only)
2.VOLUME for INPUT A and INPUT B:Theseknobscontrolthelevelofeachinputchannel(Controlsthe
master volume on the Titan 8A MKII)
3.HI and LOW EQ (equalization) controls:Theseknobscontrol theequalizationof theoveralloutput
signal providing +/- 10dB of gain for each band.
4.Remote Control:ThisPheonixconnectorcanbeusedtocontrolthevolumewithanappliedvoltage.
5.90Hz Monitor Filter switch:Usedtoreducebassbuildupduetohalfspaceloading.
6.Horn LED defeat switch: Switches off the horn power LED for discrete applications.
7.RCA L / R (Left and Right) input jacks: These jacks allow input of a stereo signal (left and right). The
signal is actively combined or “summed” providing a mono signal to the amplifier.
8.GAIN selection switch:Thisswitchselects thepropergainstructure for INPUTA. Ifamicrophone is
connected to INPUT A, use mic mode (up). If the signal source is anything other than a microphone (playback
device, keyboard or mixer output, for instance) use the line mode (down) .
9&10.POWER ON / OFF switch, POWER ´ON´ indicator LED and LIMIT indicator LED:The
switch: turns the power on and off. The bracketed LED to the left of the POWER switch illuminates when the
power switch is in the´ON´ position. The LIMIT LED illuminates when the signal limiter is limiting the level of
thesignaltopreventdistortionandoverload.
11.Output source “LOOP / MIX” switch: In the “LOOP” mode, this switch routes the signal of INPUT B to
the line level XLR OUTPUT jack, bypassing the EQ section and volume control. When in the MIX mode, this
switch routes the combined (or “mixed”) signals of both INPUT A and INPUT B to the line level XLR OUTPUT
jack.
12.XLR / ¼” COMBO input jacks for INPUT A and INPUT B: These convenient jacks allow XLR or ¼”
balanced input connections to INPUT A and INPUT B
13.POWER cord receptacle:ThisisareceptacleforastandardIEC,threeprong,groundedACelectrical
connection cord. Be sure that you are plugging into the correct source voltage that matches what is indicated
justbelowthepowercordjack.
14.XLR line level OUTPUT jack:Thisjackprovidesabalancedlineleveloutputforconnectiontoadditional
Titan™ ACTIVES, powered subwoofers or amplifiers.
13
Titan™ Series
Titan™12D / 15D CONNECTION DIAGRAM # 1
Basic microphone / playback hookup
Titan™12D / 15D CONNECTION DIAGRAM # 2
Connecting two Titan™ ACTIVE speakers together
14
OPERATING MANUAL AND USER GUIDE
TITAN™ SUB A12 REAR PANEL FEATURES
1. HEAT SINK
2. VOLUME CONTROL
3. INPUT L
4. INPUT R
5. OUTPUT R
6. OUTPUT L
7. POWER SOCKET
8. LIMIT LED
POWER LED
9. POWER SWITCH
10. PHASE SWITCH
11. CROSSOVER
FREQUENCY
CONTROL
Cooling fins for amplifier. Do not obstruct.
Adjuststhevolume.
Balanced line level input via a XLR/ ¼” combo connector.
Balanced line level input via a XLR/ ¼” combo connector.
Balanced male XLR connector provides output HIGHPASS signal.
Balanced male XLR connector provides output HIGHPASS signal.
ThisistheconnectionfortheIECACpowerconnector.
LED indicator illuminates when the signal limiting function is activated.
LED indicator illuminates when the unit is powered up.
Turns the power on and off to the subwoofer amplifier module.
Selects the polarity of the signal being sent to the subwoofer.
0°selectsthesignalpolarityasitappearsattheinput.
The180°selectioninvertsthepolarityofthesignal.
Adjustable80Hz/100Hz/120Hz/150Hz/180Hz/200Hz.
15
Titan™ Series
Titan™ Sub-A12 CONNECTION DIAGRAM # 1
TWO CHANNEL SYSTEM WITH HIGHPASS OUTPUT
16
OPERATING MANUAL AND USER GUIDE
Titan™ Sub-A12 CONNECTION DIAGRAM # 2
USING TWO Titan™ Sub-A12 WITH
TWO POWER SPEAKERS
17
Titan™ Series
Titan™ Sub-A15 - REAR PANEL FEATURES
1. INPUT A - Balanced line level input via a XLR / ¼” combo connection.
2. OUTPUT A - Balanced male XLR connection provides “THRU” or HIGHPASS signal (depending on switch setting).
3. SPEAKER LEVEL INPUT - Allows for connection of an external amplifier to use the Titan™ Sub-A15 as a passivesubwoofer.
NOTE: Disconnect the power cord when using the Titan™ Sub-A15 in this mode.
4. INPUT B - Balanced line level input via a XLR / ¼” combo connection.
5. OUTPUT B - Balanced male XLR connection provides output “THRU” or HIGHPASS signal (depending on switch setting).
6. HEATSINK - Cooling fins for amplifier. Do not obstruct.
7. VOLUME CONTROL-Adjustsvolumelevelofthesubwoofer.
8. THRU / HIGHPASS SWITCH - Selects the signal type that is routed to the OUTPUT jacks, “THRU” sends the unprocessed signal to the outputs. “HIGHPASS” filters the signal at 100Hz to the outputs.
9. PHASE SWITCH - Selects the polarity of the signal being sent to the subwoofer. 0° selects the signal polarity asitappearsattheinput.The“180°”selectioninvertsthephaseofthesignal.
10.LIMIT LED - LED indicator illuminates when the singal limiting function is activated.
11. POWER LED - LED indicator illuminates when the unit is powered up.
12.POWER SOCKET-ThisistheconnectionfortheIECACpowerconnector.
13.POWER SWITCH - Turns the power on and off to the subwoofer amplifier module.
VOLUME
CAUTIONRISK O F ELECTR IC SHO CK
D O N O T O PE N !AVIS: RISQUE DE CHOC ELECTRIQUE -NE PAS OUVRIR
WARNING: SHOCK HAZARD DO NOT OPEN
PHASE
THRU 0°
180°(100Hz)HIGHPASS
N 2082
ON
OFF(B A L A N C ED ) (B A L A N C ED )
INPUT
INPUT
OUTPUT
OUTPUT(B A L A N C E D )(B A L A N C E D )
A
B
SPEAKERLEVEL IN
0
MAX8 II
I I
I I
I
I
I
I
WWW.WHARFEDALEPRO.COM
POWER AC 220-240V~50Hz 400WFUSE T4AL250V
SERIALNUMBER
OUTPUT A
OUTPUT B
SPEAKERLEVEL INPUT
INPUT A
HEATSINK
PHASE SWITCH
LIMIT LED
POWER LED
POWER SOCKET
POWER SWITCH
VOLUMECONTROL
THRU/HIGHPASSSWITCH
INPUT B
1
234
5
6
7
891011
LIMIT
1213
_
18
OPERATING MANUAL AND USER GUIDE
Titan™ Sub-A12 CONNECTION DIAGRAM # 1
TWO CHANNEL SYSTEM WITH HIGHPASS OUTPUT
NOTE: This same connection configuration can be used with OUTPUT A and B used in a full-
range mode when the THRU/HIGHPASS switch is in the "THRU" (up) position.
19
Titan™ Series
CONNECTION DIAGRAM # 2
USING TWO Titan™ Sub-A15's WITH
TWO POWERED SPEAKERS
20
OPERATING MANUAL AND USER GUIDE
SPECIFICATIONS - Titan™ PASSIVE SERIES
Loudspeaker Type:
Frequency Response (+/–3dB):
Sensitivity (1W@1M):
Peak SPL:
HF Coverage (H x V):
System Impedance:
POWER (WATTS)
Continuous:
Music:
Peak:
LF DRIVER
Size:
Coil Size:
HF DRIVER/ HORN
Coil Size:
Exit Size:
Diaphragm Material:
HF Driver Protection:
Long-Throw EQ Compensation:
Horn Type:
Throat Size:
CROSSOVER
Type/Frequency/Filter:
ENCLOSURE
Shape/ Material:
Rigging:
COLOURS
OUTPUT CONNECTORS
DIMENSIONS/WEIGHTS
Weight:
Dimensions (H x W x D):
Titan™ 8
8" 2-way
70 - 20kHz
96dB
124dB
90˚ x 60˚
8 ohm
150W
300W
600W
203mm/ 8"
38.86mm / 1.53"
Compression Driver
25mm/1"
30mm/1.2"
Cloth
Bulb
N/A
EWG™ - Elliptical Waveguide
25mm/1"
2-way 2.4KHz / Linkwitz-Riley
Trapezoidal/ Polypropylene
(8) M6 threaded rigging points
+ (4) M6 threaded rigging points
on bottom in Omnimount®
30.0-type footprint + Speaker pole-
mount receptacle with lock screw
+ 1 built-in carry handle + Optional
wall-mount bracket + (Optional
dual-unit array speaker stand
hardware)
Grey or Black or White
2 x 1/4" jacks + 2 x NL4
5.5kg / 12.1lbs
396 x 266 x 221mm/
15.59" x 10.47" x 8.7"
Titan™ 12
12" 2-way
55 - 20kHz
98dB
128dB
90˚ x 60˚
8 ohm
250W
500
1000
305mm/ 12"
64.26mm / 2.5"
Compression Driver
44mm/1.75"
25mm/1"
Titanium
DTF™ Dynamic Thermal Filament
3dB boost (long-throw) / Flat
(near-�eld)
EWG™ - Elliptical Waveguide EWG™ - Elliptical Waveguide
25mm/1"
2-way 2.2KHz / Linkwitz-Riley
Trapezoidal/ Polypropylene
(10) M8 threaded rigging points
+ (4) M8 threaded rigging points
on bottom in Omnimount®
60.0-type footprint + Speaker
pole-mount receptacle with lock
screw + Optional wall-mount
bracket + (Optional dual-unit
array speaker stand hardware)
Grey or Black or White
2 x 1/4" jacks + 2 x NL4
12kg / 26.4lbs
556 x 384 x 312mm/
21.88" x 15.1" x 12.3"
Titan™ 15
15" 2-way
50 - 20kHz
97dB
129dB
90˚ x 60˚
8 ohm
400W
800W
1600W
381mm/ 15"
75mm / 3.0"
Compression Driver
51mm/ 2.0"
25mm/1"
Titanium
DTF™ Dynamic Thermal Filament
N/A
25mm/1"
2-way 1.8KHz / Linkwitz-Riley
Trapezoidal/ Polypropylene
(10) M8 threaded rigging points
+ (4) M8 threaded rigging points
on bottom in Omnimount®
60.0-type footprint + Speaker
pole-mount receptacle with lock
screw + Optional wall-mount
bracket + (Optional dual unit
array speaker stand hardware)
Grey or Black or White
2 x 1/4" jacks + 2 x NL4
22kg / 48.4lbs
708.3 x 477.8 x 401.77mm/
27.9" x 18.8" x 15.8
21
Titan™ Series
SPECIFICATIONS - Titan™ ACTIVE SERIES
System Type
Frequency Response (+/-3dB)
Low Frequency Driver (mm/in.)
High Frequency Driver
Exit Size (mm / inches)
Dispersion (H x V)
Amplifiers
Low Frequency (Class D)
High Frequency (Class D)
Electronic Crossover:
Crossover Frequency
Equalization:
Subsonic Filter
Amplifier Protection
Power On
Thermal
Low Line Voltage Shut Down
Driver Protection
DC Protection
Short Protection
Clip Limiter:
Limiter Indicator
Power Indicator
Titan™ 8 ACTIVE MK II
70-20kHz
205mm / 8”
Compression Driver
90° x 60°
2.4kHz
30Hz, Second -order filter
Power switch on / off mute
Amplifier shutdown, auto reset
Independent LF and HF limiters
Yes
Yes
Red LED
Green LED
Titan™ 12 D
Active 12” 2-way Bi -Amplified
55-20kHz
305mm / 12”
Titanium Compression Driver
25mm / 1"
90° x 60°
24dB/octave Linkwitz-Riley
2.3kHz
High (±10dB) 10kHz Shelving
Low (±5dB) 100Hz Shelving
30Hz, Second -order filter
Power switch on / off mute
Amplifier shutdown, auto reset
60% Nominal line voltage
Independent LF and HF limiters
Yes
Yes
Turns on approx 250W output
Red LED
Green LED
Titan™ 15 D
Active 15” 2-way Bi -Amplified
50-20kHz
381mm / 15”
Titanium Compression Driver
25mm / 1"
90° x 60°
24dB/octave Linkwitz-Riley
1.8kHz
High (±10dB) 10kHz Shelving
Low (±10dB) 100Hz Shelving
30Hz, Second -order filter
Power switch on / off mute
Amplifier shutdown, auto reset
60% Nominal line voltage
Independent LF and HF limiters
Yes
Yes
Turns on approx 350W output
Red LED
Green LED
Active 8” 2-way Bi-Amplified
30mm / 1.2”
Rated 150W continuous, 300W Peak
Rated 30W continuous, 60W Peak
24dB per octave Linkwitz-Riley
Low (±10dB) 100Hz Shelving
< 80VAC
Turns on approx 150W output
Rated 250W continuous, 500W Peak Rated 350W continuous, 700W Peak
Rated 50W continuous, 100W Peak Rated 70W continuous, 140W Peak
High (±10dB) 10kHz Shelving
22
OPERATING MANUAL AND USER GUIDE
SPECIFICATIONS - Titan™ ACTIVE (Con't)
Inputs
Input A – type
Input Sensitivity
Maximum Input Level
Input Connector
Input Impedance
Maximum Input Level
Input B – type
Input Sensitivity
Maximum Input Level
Input Connectors
Line Output
Impedance:
Sensitivity
AC Power details
Power Supply
AC Power Options
Power On Indicator
Rigging / Bracket / Mounting
Options
Enclosure Material
Colours
Dimensions H x W x D (mm)
Dimensions H x W x D (in)
Net Weight (kg / lbs)
Gross Weight (kg / lbs)
Titan™ 8 ACTIVE
Switchable balanced mic or line
level input
+22dBu
XLR - 1/4” Combo jack
+22dBu
High Efficiency Switching Mode
Power Supply
Green LED Green LED Green LED
8 M6 threaded inserts including 4
M6 threaded
inserts on bottom in OmniMount
30.0-type footprint
Pole-mount receptacle with lock
screw
1 carry handles
Optional wall-mount bracket
Injection Moulded Polypropylene
Grey or white or black
396 x 266 x 221
15.6 x 10.5 x 8.7
Titan™ 12 D
Switchable balanced mic or line
level input
Mic: -40dBu (-42.2dBv or
7.75mVrms)
+22dBu
XLR - 1/4” Combo jack
+22dBu
Line level input
XLR - 1/4” Combo jack: 0dBu (-2.2
dBv or 0.775Vrms)
XLR - 1/4” Combo jack: 0dBu (-2.2
dBv or 0.775Vrms)
RCA: 0dBu (-2.2dBv or
0.775Vrms)
+22dBu
Combo ja ck: 1 / 4" - XLR / Summe d
dual RCA jacksSwitchable LOOP / MIX Balanced
Male XLR
Balanced: 200 ohm Unbalanced:
100 ohm
High Efficiency Switching Mode
Power Supply
AC100~120V / 220~240 V, 50 /
60Hz
10 M8 threaded inserts including
4 M8 threaded
inserts on bottom in OmniMount
60.0-type footprint
Pole-mount receptacle with lock
screw
2 carry handles (one on each
side)
Optional wall-mount bracket
Injection Moulded Polypropylene
Black
556 x 384 x 312
21.9 x 15.1 x 12.3
12.4kg / 27.28lbs
15.5kg / 34.lbs
Titan™ 15 D
Switchable balanced mic or line
level input
Mic: -40dBu (-42.2dBv or
7.75mVrms)
+22dBu
XLR - 1/4” Combo jack
+22dBu
Line level input
RCA: 0dBu (-2.2dBv or
0.775Vrms)
+22dBu
Combo jack: 1/4" - XLR /
Summed dual RCA jacksSwitchable LOOP / MIX Balanced
Male XLR
Balanced: 200 ohm Unbalanced:
100 ohm
High Efficiency Switching Mode
Power Supply
AC100~120V / 220~240 V, 50 /
60Hz
10 M8 threaded inserts including
4 M8 threaded
inserts on bottom in OmniMount
60.0-type footprint
Pole-mount receptacle with lock
screw
2 carry handles (one on each
side)
Optional wall-mount bracket
Injection Moulded Polypropylene
Black
708.3 x 477.8 x 401.8
27.9" x 18.8" x 15.8
22.9kg / 50.38lbs
27.7kg / 60.94lbs
Mic: -47dBu (-49.2dBv or
3.4mVrms)
Line: 0dBu (-2.2dBv or 0.775Vrms)
Balanced: 20kΩ -
Unbalanced: 10kΩ
Balanced: 10kΩ -
Unbalanced: 5kΩ
Balanced: 10kΩ -
Unbalanced: 5kΩ
+22dBu
Combo jack: 1/4" - XLR
0dBu (-2.2dBv or 0.775Vrms) 0dBu (-2.2dBv or 0.775Vrms) 0dBu (-2.2dBv or 0.775Vrms)
AC100~240V, 50 / 60Hz
6.25kg / 13.75lbs
8.15kg/ 17.93lbs
Switchable LOOP / MIX
Balanced Male XLR Connector
N/A
N/A
Balanced: 1k ohm Unbalanced:
500 ohm
MKII
Line: 0dBu (-2.2dBv or 0.775Vrms) Line: 0dBu (-2.2dBv or 0.775Vrms)
23
Titan™ Series
SPECIFICATIONS - Titan™ SUB SERIES
System Type
Frequency Response (+/-3dB)
Enclosure Material
Enclosure Colour
Frame material
Size (mm / inches)
Coil Size (mm / inches)
Impedance
Speaker Pole Adapter
Inputs A & B - Type / Connection
Output A & B Type / Connection
Input Sensitivity
High Pass Frequency Selection
Phase Switch Selection
Crossover Frequency (HZ)
Speaker Level Input Impedance
Speaker Level Input Connection
Amplifier Power: Continuous
Amplifier Power: Peak
Power On Indicator
Power On Protection
Thermal Protection
Low Line Voltage Shut Down
Driver Protection
DC Protection
Short Protection
Clip Limiter:
Limiter Indicator
Power Indicator
Dimensions H x W x D: (mm)
Dimensions H x W x D (in)
Weight (Net) kg / lbs
TITAN™ Sub-A15
Band-pass subwoofer
45-150Hz
18mm Plywood
Grey or Black
Die-cast aluminium frame
404mm / 15”
75 / 3”
4 ohm
Yes
Balanced Line Level inputs via two
combo connectors
Balanced Line Level inputs via two
combo connectors
0.56V
100Hz
0° / 180°
150
1/4” TS Phone input
4Ω
400W
600W
LED
Power switch on / o� mute
Ampli�er shutdown, auto reset
60% Nominal line voltage
Independent LF limiters
Yes
Yes
Turns on approx 400W output
Red LED
Blue LED
630.0 x 478.0 x 640.0
24.8 x 18.8 x 25.2
45.48kg / 100.0lbs
Titan™ Sub-A12
Re�ex subwoofer
55-200Hz
15mm MDF
Grey or Black
steel frame
305mm / 12”
64.26mm / 2.5”
4 ohm
Yes
Balanced Line Level inputs via
two combo connectors
Balanced Line Level inputs via
two combo connectors
0.37V
150Hz
0° / 180°
80/ 100/ 120/ 150/ 180/ 200
(adjustable)
250W
500W
LED
Power switch on / o� mute
Ampli�er shutdown, auto reset
60% Nominal line voltage
Independent LF limiters
Yes
Yes
Turns on approx 250W output
Red LED
Blue LED
360.0 x 493 x 431.0
14.2 x 19.4 x 16.9
22.31kg /49.0lbs
24
OPERATING MANUAL AND USER GUIDE
DIMENSIONS
25
Titan™ Series
DIMENSIONS
26
OPERATING MANUAL AND USER GUIDE
DIMENSIONS
27
12.28"312mm
21.88"556mm
15.11"384mm
12.28"312mm
7.1"180mm
15.83”402mm
27.87”708mm
18.81”478mm
15.83”402mm
Titan™ Series
DIMENSIONS
28
OPERATING MANUAL AND USER GUIDE
WharfedaleProproductsarewarrantedofmanufacturingormaterialdefectsforaperiodofoneyearfromtheoriginaldateofpurchase.Intheeventofmalfunction,contactyourauthorizedWharfedaleProdealerordistributorforinformation.
*Be aware that warranty details may differ from country to country. Contact your dealers or distributor for information.Thesetermsdonotinfringeyourstatutoryrights.
WHARFEDALE PRO LIMITED WARRANTY
29
WharfedaleProfessionalIAG HOUSE, Sovereign Court, Ermine Business Park Huntingdon, Cambs, PE29 6XU, England
www.wharfedalepro.comWharfedale Professional reserves the right to alter or improve specifications without notice.
All rights reserved © 2010 Wharfedale Pro. Wharfedale Pro is a member of the International Audio Group (IAG).