NUTORK CORPORATIONNUTORK CORPORATIONNUTORK CORPORATIONNUTORK CORPORATIONNUTORK CORPORATION
NS Series Pneumatic ActuatorNS Series Pneumatic ActuatorNS系列拨叉式气动执行器NS系列拨叉式气动执行器NS Series Pneumatic ActuatorNS Series Pneumatic ActuatorNS系列拨叉式气动执行器NS系列拨叉式气动执行器NS Series Pneumatic ActuatorNS系列拨叉式气动执行器
1. 指示器(Indicator/Output Shaft) A position indicator with Namur mounting is the standard on allNUTORK NS series pneumatic actuators for ancillary accessories.位置指示器及Namur安装标准于NUTORK NS系列拨叉式气动执行器
2. 活塞杆及轴承(Piston Rods and Rod Bearings) Steel alloy piston rod with hard chrome plated, The steel alloy rodbearings with PTFE coated, provide low friction and extend the operation life. 合金钢活塞杆表面镀硬铬处理,合金钢内衬PTFE轴承,保证低的磨擦系数及提高使用寿命.
3. 销轴(Yoke Pin) Steel Alloy with hardened treatment and hard chrome plated whichprovide excellent anti-abrasion and transfer the torque to scotch yoke. 表面镀硬铬增加耐磨性将活塞杆的力矩平稳传给拨叉.
4. 隔板(Partition Plate) To divide body from piston housing and reduce the airconsumption also keep from objects. 将箱体与气缸活塞分隔以减少空气消耗量,防止异物进入气缸.同时为活塞导向保证动作平稳.
5. 活塞缸体(Cylinder) Cast Steel with RPTFE coated which provides high stability with the minimum friction and long life. 铸钢内表面喷涂RPTFE增加气缸自润性,减少摩擦以提高使用寿命及运行的平稳性.
6. 限位螺栓(Bi-directional Travel Adjustment) 0°and 90°with standard adjustment ±5°(0°及90°±5°标准调整范围).
7. 箱体(Dual Valve Mounting Interface Actuator Body) The unique one-piece housing assures accurate alignment of both the torque shaft and the piston rod. Allows the flexibility to change the actuator fail mode, without disassembly and simply inverting the actuator. They may be installed in any position; parallel or at right angles to flow line, in the vertical or the horizontal plane. 一体化及防冲击结构设计并精确装配固定输出轴及活塞杆.并且无需分解拆卸既可轻易的变换气缸的转动方向,可安装于任何位置.
8. 拨叉(Scotch Yoke) The slot in the scotch yoke mechanism is precision machined. The yoke pin is induction hardened and chrome plated. It is supported at the top and bottom by a guide slot in the housing and the yoke pin rollers are hardened steel. 拨叉上的插槽经精密机加工,合金钢销轴经硬化及镀硬铬处理并上下两端固定于拨叉上的插槽.
9. 抗腐蚀涂装(Corrosion Resistant Painting) NUTORK NS series pneumatic actuator incorporate 3 stages of external corrosion resistant painting( Primer paint: Anti-rust painting and two parts of epoxy coating) to resist severe environment in the industries of chemical, petroleum and power plant.NUTORK NS系列拨叉式气动执行器共有三层涂装(底层防锈底漆,两层环氧树脂防蚀涂装),以提供不同恶劣的使用环境.
10.使用工作温度范围 (Temperature Range) The standard temperature range(NBR seal) is -20℃ to +80℃(-30 to +144 ), The options are available for low temperature (Silicone seal)-45℃ to +80℃(-81 to +144 ) and high temperature(Viton seal) -20℃ to +177℃(-30 to +319 )标准工作温度范围(密封圈:丁氰橡胶): -20℃ to +80℃(-30 to +144 ),低温工作温度范围(密封圈:硅橡胶):-45℃ to +80℃(-81 to +144 )及高温工作温度范围(密封圈:氟橡胶): -20℃ to +177℃ (-30 to +319 )
11. 扭矩范围(Torque Range) The actuator range of NS type pneumatic actuator consists of 10 models, with torques from 999Nm(8,842in.lbs) to 127,710Nm(1,130,361in.lbs) at 5 bar(70psig) air supply. NS系列拨叉式气缸共有10个型号,扭矩范围从999Nm(8,842in.lbs)到127,710Nm(1,130,361in.lbs)于5bar气源压力.
12. NS series pneumatic actuators have valve mounting pads in accordance with MSS SP-101 or ISO5211 standard. NS系列拨叉式气缸提供MSS SP-101或ISO5211安装接口标准于装配阀门
13.手动装置(选配)Manual Override(Optional) Depend on customer requirements and actuator size. Jackscrew or hydraulic manual overrides can be supplied. 依照客户需求及气缸尺寸,可提供手轮手柄或液压手动装置,
ISO或MSS安装标准(ISO or MSS Mounting)
F F F F F F
F FF F F F
5 8 7
2314
6
1 NUTORK www.nutork.com TM
输出扭矩特性
2928
2736
33
32
3123
34
35
5
5
62
4
3
18
1110
9
7
4
24
2523
22
30
22
17
19
18
21
2025
1011
98
723
1615
151312
14
14
1820
2117
19
3016
24
26
Single ActingSpring Return Type单作动气缸
双作动气缸Double Acting Type
2NUTORK www.nutork.com TM
Cast Steel Housing + Viton Seal / 铸钢本体+PTFE涂层,氟橡胶密封圈Item项次
Part Name 部件名称
Material材质
Item项次
Part Name部件名称
Material材质
Item项次
Part Name 部件名称
Material材质
1 Housing WCB(铸钢) 14 Sleeve Steel Alloy+Chrome Plated 27 Nut 35CrMo
2 Cover WCB(铸钢) 15 BushingCS+PTFE Coated (铸钢+PTFE涂层) 28 Stroke Bolt 35CrMo
3 Scotch Yoke WCB+PTFE Coated (铸钢+PTFE涂层) 16 Washer Spring Steel 29 Nut 35CrMo
4 Trust Bearing PTFE(聚四氟乙烯) 17 PlateWCB+PTFE Coated (铸钢+PTFE涂层) 30 Pipe 304SS
5 BushingWCB+PTFE Coated (铸钢+PTFE涂层) 18 Gasket XB450 31 Piston
WCB+PTFE Coated (铸钢+PTFE涂层)
6 Bolt 35CrMo 19 Sleeve WCB+PTFE Coated (铸钢+PTFE涂层) 32 External Housing
CS+ENP(铸钢+镀镍涂层)
7 Cylinder WCB+PTFE Coated (铸钢+PTFE涂层) 20 O-Ring Viton(FKM),氟橡胶 33 Internal Housing
CS+ENP(铸钢+镀镍涂层)
8 Bolt 35CrMo 21 O-Ring Viton(FKM) ,氟橡胶 34 External Spring Spring Steel(55CrMnA)
9 Stroke Bolt 35CrMo 22 PistonWCB+PTFE Coated (铸钢+PTFE涂层) 35 Internal Spring Spring Steel(55CrMnA)
10 Gasket WCB+Rubber 23 O-Ring Viton(FKM) ,氟橡胶 36 CapWCB+PTFE Coated (铸钢+PTFE涂层)
11 Cover Nut WCB+Zinc Plated (铸钢+镀锌处理) 24 O-Ring Viton(FKM) ,氟橡胶
12 Piston Rod Steel Alloy+ Chrome Plated (合金钢+镀铬处理) 25 Nut 35CrMo
13 Yoke Pin Steel Alloy+Chrome Plated (合金钢+镀铬处理) 26 Bolt 35CrMo
Double Acting Type Single Acting TypeO
utpu
t Tor
que
Out
put T
orqu
e
Break Torque
Running Torque
Spring Break Torque
Air Break Torque
Spring End Torque
Air End Torque
0° 45° 90° 0° 45° 90°Output Torque Curve
3 NUTORK www.nutork.com TM
双作动气缸
输出扭矩曲线图
开启扭矩
弹簧开启扭矩 空气开启扭矩
运行扭矩
空气最后扭矩弹簧最后扭矩
单作动气缸
Torque Table of Double Acting Actuator / 双作动气缸输出扭矩表 N.m.Unit:in.lbs
Air Supply Pressure-空气供给压力 (bar / psig) Model 型号
Output Torque 输出扭矩 3 / 44 4 / 58 5 / 73 6 / 87
599 799 999 1198 Break & End 开启 & 最后 5302 7072 8842 10603
355 474 592 711NS13DA
Running 运行 3142 4195 5240 6293
1285 1714 2142 2570 Break & End 开启 & 最后 11374 15171 18959 22747
763 1017 1271 1525 NS17DA
Running 运行 6753 9001 11250 13498
2866 3821 4777 5730 Break & End 开启 & 最后 25367 33820 42281 50716
1701 2269 2836 3400 NS20DA
Running 运行 15056 20083 25101 30093
4485 5980 7475 8970 Break & End 开启 & 最后 39697 52929 66161 79393
2752 3670 4587 5505 NS25DA
Running 运行 24358 32483 40600 48725
6871 9162 11453 13740 Break & End 开启 & 最后 60815 81093 101371 121613
4080 5440 6800 8160 NS28DA
Running 运行 36112 48149 60187 72224
9826 13110 16387 19665 Break & End 开启 & 最后 86970 116037 145041 174055
5487 7316 9145 10974 NS32DA
Running 运行 48565 64754 80942 97131
14000 18670 23337 28000 Break & End 开启 & 最后 123914 165248 206556 247828
8310 11080 13856 16627 NS35DA
Running 运行 73552 98069 122639 147166
32000 43400 54300 65160 Break & End 开启 & 最后 283232 384133 480609 576731
17300 23000 28800 34560 NS49DA
Running 运行 153122 203573 254909 305891
49300 65740 82170 98600 Break & End 开启 & 最后 436354 581865 727287 872709
28080 37440 46800 56160 NS60DA
Running 运行 248536 331381 414227 497072
76626 102170 127710 153255 Break & End 开启 & 最后 678217 904307 1130361 1356460
42780 57050 71310 85575 NS70DA
Running 运行 378646 504950 631165 757424
Dimension / 尺寸图(NS13~NS28)
Top Mounting顶部安装
NS17/NS20 NS25/NS28
Bottom Flange / 底部安装
NS13
4-M6
30
80
4×
4
4NUTORK www.nutork.com TM
L(SR, Single Acting Type)单作动气缸L(DA, Double Acting Type)双作动气缸
0 0
N.M.Torque Table of Single Acting Actuator / 单作动气缸输出扭矩表 Unit:
in.lbs
Air Supply Pressure- 空气供给压力 (bar / psig) 4 / 58 5 / 73 6 / 87
Spring Torque Output 弹簧输出扭矩
Air Torque Output ( 空气输出扭矩 )Model 型号
90° 0° 0° 90° 0° 90° 0° 90°462 280 519 337 719 537 918 736
NS13SR 4089 2478 4594 2983 6364 4753 8125 6514 1024 650 1060 690 1488 1118 1916 1546
NS17SR 9063 5753 9382 6107 13170 9895 16959 13684 2328 1450 2371 1493 3327 2449 4280 3402
NS20SR 20605 12834 20986 13215 29447 21676 37882 30111 3980 2520 4220 2620 5919 4156 7610 5848
NS25SR 35227 22305 37351 23190 52389 36785 67356 51761 5362 3500 5660 3800 7950 6090 10237 8377
NS28SR 47459 30979 50097 33634 70365 53903 90608 74145 7540 5020 8070 5560 11340 8830 14620 12110
NS32SR 66737 44432 71428 49212 100370 78154 129402 107186 12300 7380 11290 6370 15950 11030 20625 15700
NS35SR 108867 65320 99928 56381 141173 97627 182552 138961 17500 10000 17120 9619 23840 16340 30600 23100
NS49SR 154893 88510 151529 85138 211008 144625 270841 204458 23780 15080 27570 18870 38240 29539 48904 40200
NS60SR 210477 133473 244022 167018 338462 261450 432849 355810 36770 22660 29458 15115 42210 28080 55180 41060
NS70SR 325451 200564 260733 133783 373601 248536 488398 363422
Dimension / 尺寸图( NS32~NS70)
Bottom Flange / 底部安装 Top Mounting(NAMUR) / 顶部安装
NS32DA~NS70DA NS32SR~NS70SR
5 NUTORK www.nutork.com TM
T
4
LL1 L2
D1
B B
Bggg g
gF
g
fA A
130
30
4-M5
4
D
Cd x J
N-Md
b
Dimension Table of NS13 ~ NS28 / 尺寸表 unit:mmModel NS13DA NS13SR NS17DA NS17SR NS20DA NS20SR NS25DA NS25SR NS28DA NS28SR
A 49 49 60 60 98 98 110 110 120 120m1 132 132 176 176 232 232 278 278 300 300m2 68 68 95 95 115 115 150 150 170 170L 574 810 755 988 1060 1415 1276 1686 1360 1840L1 287 287 378 378 530 530 686 686 680 680H1 85 85 105 105 130 130 169 169 165 165H2 103 103 95 95 244 244 169 169 305 305h 35 35 35 35 35 35 35 35 35 35D ----- ----- 210 210 230 230 300 300 340 340C ----- ----- 165 165 165 165 254 254 298 298F ----- ----- 130 130 130 130 200 200 230 230
Ød0 ----- ----- 50 50 64 64 75 75 85 85b ----- ----- 14 14 18 18 20 20 22 22
Md ----- ----- 4-M20 4-M20 4-M20 4-M20 8-M20 8-M20 8-M20 8-M20Ød 25 25 25 25 25 25 25 25 25 25
Air Inlet 1/4" 1/4" 3/8" 3/8" 3/8" 3/8" 1/2" 1/2" 1/2" 1/2"t ----- ----- 53.8 53.8 68.4 68.4 79.7 79.7 90.4 90.4
Weight(Kg) 35.8 55.4 75 125 130 181 244 330 275 398
Double Acting Type / 双作动Type L ØD0 A B C D ØF f b d T J g N-Md
Weight(Kg)
NS32DA 1566 392 135 158 298 350 230 6 25 90 95.4 140 1/2 8-M20 500NS35DA 1850 440 150 145 300 350 240 6 28 100 106.4 140 1/2 8-M24 580NS49DA 2150 562 180 160 350 400 280 6 32 120 127.4 165 3/4 12-M24 930NS60DA 2610 700 220 197 450 500 360 6 36 140 148.4 180 3/4 12-M27 1570NS70DA 2610 800 150 175 450 600 360 6 36 140 148.4 180 3/4 12-M27 2160
unit:mm
Single Acting Type / 单作动Type L1 L2 ØD0 ØD1 A B W H D C F f b d T J g N-Md
Weight(Kg)
NS32SR 1405 783 392 392 135 158 380 145 350 298 230 6 25 90 95.4 140 1/2 8-M20 800NS35SR 1590 925 440 440 150 145 380 145 350 300 240 6 28 100 106.4 140 1/2 8-M24 870NS49SR 1780 965 440 562 150 145 380 145 350 300 240 6 28 100 106.4 140 3/4 8-M24 1100NS60SR 1910 850 559 670 150 175 380 145 415 356 260 6 28 100 106.4 140 3/4 8-M30 1980NS70SR 1910 850 559 770 150 175 380 145 415 356 260 6 32 120 127.4 140 3/4 8-M30 2770
unit:mm
Dimension(NS32~NS70+Hydraulic Snubber) / 尺寸表(NS32~NS70+油压装置)
NS32DA~NS70DA+Hydraulic Snubber / (NS32DA~NS70DA+油压装置)
NS32SR~NS70SR+Hydraulic Snubber / (NS32SR~NS70SR+油压装置)
6NUTORK www.nutork.com TM
Bottom Flange / 底部安装 Top Mounting(NAMUR) / 顶部安装
F
gg
L
L1
gg
4-M5N-Md
d x J
130
30
44
T
D
F
L2
B
B
WW
D0 g
g
D0
D1
Double Acting Type+Hydraulic Snubber / 双作动气缸+油压装置Type L ØD0 A B W H C D ØF f b d T J N-Md
Weight(Kg)
NS32DA-H 2430 392 135 158 380 145 298 350 230 6 25 90 95.4 140 8-M20 630NS35DA-H 2910 440 150 145 380 145 300 350 240 6 28 100 106.4 140 8-M24 750NS49DA-H 3330 562 180 160 380 160 350 400 280 6 32 120 127.4 165 12-M24 1150NS60DA-H 3920 700 220 197 400 160 450 500 360 6 36 140 148.4 180 12-M27 1780NS70DA-H 3920 800 150 175 400 160 450 600 360 6 36 140 148.4 180 12-M27 2370
Single Acting Type+Hydraulic Snubber / 单作动气缸+油压装置Type L1 L2 ØD0 ØD1 A B W H D C F f b d T J N-Md
Weight(Kg)
NS32SR-H 1405 1215 392 392 135 158 380 145 350 298 230 6 25 90 95.4 140 8-M20 860NS35SR-H 1590 1420 440 440 150 145 380 145 350 300 240 6 28 100 106.4 140 8-M24 920NS49SR-H 1780 1540 440 562 150 145 380 145 350 300 240 6 28 100 106.4 140 8-M24 1180NS60SR-H 1910 1305 559 670 150 175 380 145 415 356 260 6 28 100 106.4 140 8-M30 2150NS70SR-H 1910 1305 559 770 150 175 380 145 415 356 260 6 32 120 127.4 140 8-M30 2930
Order Information
Head Office:P.O.Box 890245,Houston,TX 77289,USATel:+1-(713)-589-4349Fax:+1-(866)-478-9624E-mail:[email protected]