Download - Model 1050 Manual
-
8/6/2019 Model 1050 Manual
1/170
Model 1050 Automated Taper
Used with Model 5000 Handler
User Manual
Version 3.2
April 1, 2010
Exatron, Inc.2842 Aiello Drive
San Jose, California 95111(408) 629-7600 Tel(800) exa-tron Tel
(408) 629-2832 Faxwww.exatron.com
-
8/6/2019 Model 1050 Manual
2/170
Copyright NoticeCopyright 2010 Exatron
This document contains proprietary information which is protected by copyright.All rights are reserved.
EXATRON MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THISMATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The information contained in this document is subject to change without notice.
-
8/6/2019 Model 1050 Manual
3/170
04/2010 Copyright Exatron, 2010 Contents-1
Table of Contents
Chapter 1: Safety and SupportChapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Exatron Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Facilities Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Air Conditioning and Environmental Requirements . . . . . . . . . . . . . . . . . 1-2
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Vacuum/Pneumatic Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Air Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Uncrating the Handler and Taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Customer In-House Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Offshore Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Exatron Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
End-of-Life Taper Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7Significance of This Manuals Version Number. . . . . . . . . . . . . . . . . . . . . . . 1-7
Typographical Conventions Used in This Manual . . . . . . . . . . . . . . . . . . . . . 1-8
Terms Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Chapter 2: System DescriptionChapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Key Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
How the Model 1050 Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Identifying Major Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Three Reels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Taper Input Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Emergency Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Motors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Override Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Index and Stack Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Seal Heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Swing Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Communication Between Handler and Taper . . . . . . . . . . . . . . . . . . . . . . . 2-19
Chapter 3: Taper Setup and RAM ListingChapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Mounting the Takeup Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Mounting the Supply Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
-- continued on next page --
-
8/6/2019 Model 1050 Manual
4/170
Model 1050 Manual
Contents-2 Copyright Exatron, 2010 04/2010
Chapter 3: Taper Setup and RAM Listing continuedAdjusting the Carrier Tape Track Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Loading the Carrier Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Loading the Sealing Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Adjusting Heat Seal Heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Adjusting Lateral Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Adjusting Downward Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Adjusting Pressure Seal Heads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Power-Up Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Setting Temperature for Heat Seal Heads . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Calibrating Device Position in Tape Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Beginning a Production Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Power-Down Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Understanding the Control Panel Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Using the Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27Modifying Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Understanding the Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Selecting Type of Tape Seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
Selecting Number of Devices to Be Put in Tape. . . . . . . . . . . . . . . . . . . 3-31
Setting Tape Pocket Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
Selecting Manual Cycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
Resetting the Count of Devices in Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Displaying the Count of Devices in Tape . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Using Manual Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Changing RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
Notes About the RAM Address Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
Warning About Motor Speeds (00C0-00CF). . . . . . . . . . . . . . . . . . . . . . 3-41
Updating Your EPROM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41
Separate Settings for Changeover Kits . . . . . . . . . . . . . . . . . . . . . . . . . 3-41
Suggested Values for Various Taper Models . . . . . . . . . . . . . . . . . . . . . 3-41
RAM Address Listing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-42
Hex-Binary Conversion Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-47
Decimal-Hex-ASCII Conversion Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-48
Chapter 4: DiagnosticsChapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Accessing DIAGNOSTICS Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Diagnostics Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
SENSOR CHECK: Tape Sensors 0-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
SENSOR CHECK: Pickup Site Sensors 8-F. . . . . . . . . . . . . . . . . . . . . . . . 4-10
-- continued on next page --
-
8/6/2019 Model 1050 Manual
5/170
04/2010 Copyright Exatron, 2010 Contents-3
Chapter 4: Diagnostics continuedOUTPUT CHECK: Solenoid Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
OUTPUT CHECK: Solenoid Toggle Check. . . . . . . . . . . . . . . . . . . . . . . . . 4-12
ALL MOTOR CHECK: Drive Motor Check . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
ALL MOTOR CHECK: Swing Arm Check . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
INTERFACE CHECK: RS-232 Port Check . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
INTERFACE CHECK: Handler Port Output Check . . . . . . . . . . . . . . . . . . . 4-18
Checking Communication Between 5000 Handler and 1050 Taper . . . . . . 4-19
Setting Up HyperTerminal for 1050 Taper . . . . . . . . . . . . . . . . . . . . . . . 4-19Configuring a Connection Session. . . . . . . . . . . . . . . . . . . . . . . . . . 4-19Testing Communication from PC to Taper. . . . . . . . . . . . . . . . . . . . 4-24
Setting Up HyperTerminal for 5000 Handler. . . . . . . . . . . . . . . . . . . . . . 4-26
Chapter 5: Dictionary of Displayed MessagesChapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Model 1050 Handler Status and Error Messages . . . . . . . . . . . . . . . . . . . . . 5-3
#### OLDNEW #### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
00## DATA ## . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
ADD LEADER DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
ADD LEADER UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
ALIGN MOTORS ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
ALL MODES OFF ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
ALL MOTOR CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
ALL MOTORS OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
CHANGE RAM ? NO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
CHANGE RAM ? YES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5CHECK SUM ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
CHK VAC ADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
COUNT SET TO 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
CPU ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
DIAGNOSTICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
DRIVE MOTOR CHK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
EMPTY POCKET ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
EXATRON TAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
FIND MOTOR HOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
FULL T = ###### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
GAP STEPS = #### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8HANDLER OUT CHK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
HOME SENSOR ERR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
HOME SWING HEAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
INTERFACE CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
JOG LEFT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
JOG RIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
-- continued on next page --
-
8/6/2019 Model 1050 Manual
6/170
Model 1050 Manual
Contents-4 Copyright Exatron, 2010 04/2010
Chapter 5: Dictionary of Displayed Messages continuedLOAD DEFAULT NO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
LOAD DEFAULT YES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
LOAD EPROM>RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
LOAD REMOTE RAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
LOOP MODE ON ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9MANUAL ###### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
MEMORY ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
MOD SET UP ? NO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
MOD SET UP ? YES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
MOTOR BUSY ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
MOTOR ERROR ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
MOTOR A OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
MOTOR B OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
MOTOR HOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
MOVE TAPE LEFT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
MOVE TAPE RIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12NO POCKET? ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
NOT UP TO TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
OFFSET = #### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
OFFSET>GAP ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
PASSWORD ABC? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
PAUSED ###### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
POCKETS = ###### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
RAM AUTO RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
RESET COUNT NO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
RESET COUNT YES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
ROTATE DOWN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13ROTATE UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
RS-232 CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
SEN0-7 01234567 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
SEN8-F 89ABCDEF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
SENSOR CHECK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
SET GAP ? NO/YES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
SET OFFSET = #### . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
SOLENOID CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
STOP MODE ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
STOP MODE ON ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
SUM CHECK =. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15SUM CHECK ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
TAKE UP MOTOR ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
TAKE UP REEL ERR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
TAPE GAP LOST ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
TAPE IS FULL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
-- continued on next page --
-
8/6/2019 Model 1050 Manual
7/170
04/2010 Copyright Exatron, 2010 Contents-5
Chapter 5: Dictionary of Displayed Messages continuedTEST TAPE MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
THANK YOU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
THERMAL OR PSA ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
TRANSFER ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
TURN ON REMOTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17UART OUT ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
UPSIDE DOWN ERR ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
ZERO COUNT ERR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Chapter 6: Servicing and TroubleshootingChapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Seal Head Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Pressure-Sensitive Heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Heat Seal Heads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Air Regulator Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3Checking Air Regulator Shutoff Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Adjusting Air Pressure on the Regulator. . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Checking the Moisture/Dirt Trap in the Air Regulator . . . . . . . . . . . . . . . . 6-4
Solenoid Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Fiberoptic Photoelectric Sensor Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Chapter 7: Parts ListGuide to the Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Exatron (Part Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Part Quantity Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Lists of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Chapter 8: Prints
Index
-
8/6/2019 Model 1050 Manual
8/170
Model 1050 Manual
Contents-6 Copyright Exatron, 2010 04/2010
-
8/6/2019 Model 1050 Manual
9/170
04/2010 Copyright Exatron, 2010 Figures-1
List of Figures
Figure 1-1: Emergency Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Figure 1-2: Air Line Attached to Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Figure 2-1: Key Device Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Figure 2-2: Reels on Taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-3: Tape Track with Swing Armat Pickup Site (Left), at Taper (Right) . . . . . . . . . . . 2-4
Figure 2-4: Other Features of Taper (Model 201). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-5: Index Pin Retracted (Left), Extended (Right). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-6: Cover Foot Retracted From Pickup Site and Stack Pin Extended (Left); Cover Foot
Extended Over Pickup Site and Stack Pin Retracted (Right) . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Figure 2-7: Phase Motor Driving Swing Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Figure 2-8: Tape Drive Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Figure 2-9: Takeup Reel Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-10: Device at Stack Sensor (A, Top); Device at Pickup Site Sensor (B, Bottom) . . . . 2-10
Figure 2-11: Device at Stack Sensor (A, Left); Device at Pickup Site Sensor (B, Right) . . . . . 2-10
Figure 2-12: Taper Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Figure 2-13: Empty Pocket Sensor (5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Figure 2-14: Out-of-Pocket Sensor (7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Figure 2-15: Gap Sensor (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Figure 2-16: Carrier Tape Out Sensor (6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Figure 2-17: Takeup Arm Sensor (3) Closed (Left), Open (Right). . . . . . . . . . . . . . . . . . . . . . . 2-13
Figure 2-18: Swing Arm Home Sensor (9, Left); Swing Arm at Home (Right). . . . . . . . . . . . . 2-14
Figure 2-19: Tape-and-Reel Override Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Figure 2-20: Heat Seal Heads with Counterbalance Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Figure 2-21: Pressure-Sensitive (PSA) Seal Heads with Counterbalance Weight . . . . . . . . . . . 2-16
Figure 2-22: Swing Arm at Pickup Site (Left), at Tape Drop Site (Right) . . . . . . . . . . . . . . . . . 2-17
Figure 2-23: Pickup Head Retracted (Left), Extended (Right) . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Figure 2-24: Path and Limits of Swing Arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Figure 2-25: Communication WiringOn 1050 Side (Left), On 5000 Side (Right) . . . . . . . . . 2-19
Figure 2-26: Connection Port for Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Figure 2-27: TAPE-346-E1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Figure 3-1: Locking Hub on Takeup Reel with Alignment Pins . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Figure 3-2: Supply Reel Tape Unwound from Top. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3Figure 3-3: Carrier Tape Track at Different Widths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Figure 3-4: Track Width Locking Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Figure 3-5: Carrier Tape Under Guide At Top Supply End of Track . . . . . . . . . . . . . . . . . . . . . . 3-5
Figure 3-6: Lifting Pressure Roller Arm and Pushing In Keeper PinTwo Styles . . . . . . . . . . . 3-6
-
8/6/2019 Model 1050 Manual
10/170
Model 1050 Manual
Figures-2 Copyright Exatron, 2010 04/2010
Figure 3-7: Takeup Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Figure 3-8: Tape Drive Gear Adjustment Knob with Blue Locking Knob Unscrewed . . . . . . . . 3-7
Figure 3-9: Gear Adjustment Narrowed (Left); Widened (Right). . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Figure 3-10: Sealing Tape PlatesOutside (Left), Inside (Right) . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Figure 3-11: Sealing Tape Threaded to Sealing Tape Guide Assembly for PSA . . . . . . . . . . . . . 3-9
Figure 3-12: Sealing Tape Threaded to Sealing Tape Guide Assembly for Heat . . . . . . . . . . . . . 3-9
Figure 3-13: Sealing Tape Threaded Under Guide Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Figure 3-14: Two Widths of Guide BlocksTop View (Left); Bottom View (Right). . . . . . . . 3-10
Figure 3-15: Placement in Grooves of Guide Blockof Sealing Tape (Left) and Carrier Tape
(Right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Figure 3-16: Guide Rod Removed from One Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Figure 3-17: Guide Block Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Figure 3-18: Semicircular Seal Head with Adjustment Screw . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Figure 3-19: Example of Good Tape Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Figure 3-20: Three-Gram and One-Gram Weights (Left); One-Gram Weight on Heat Seal
Counterbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3-21: Pair of Pressure Seal Heads with Lateral Adjustment Screws . . . . . . . . . . . . . . . . 3-15
Figure 3-22: Three-Gram and One-Gram Weights (Left); One-Gram Weight on PSA
Counterbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Figure 3-23: Air Regulator Turned Off (Left), On (Right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
Figure 3-24: Emergency Stop Button on Model 5000 Handler. . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Figure 3-25: Emergency Stop Buttons for Both Handler and Taper. . . . . . . . . . . . . . . . . . . . . . 3-19
Figure 3-26: Heater Controller Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Figure 3-27: SET Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Figure 3-28: Up Arrow Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Figure 3-29: Digit in Ones Position Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Figure 3-30: Left Arrow Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Figure 3-31: Digit in Tens Position Selected. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Figure 3-32: Temperature Set Before the SET Button Is Pressed. . . . . . . . . . . . . . . . . . . . . . . . 3-22
Figure 3-33: Temperature Set After the SET Button Is Pressed . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Figure 3-34: Down Arrow Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Figure 3-35: Temperature Set to Zero Before the SET Button Is Pressed . . . . . . . . . . . . . . . . . 3-24
Figure 3-36: Tape Calibration Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Figure 3-37: Swing Arm Calibration Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Figure 3-38: Key Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Figure 3-39: Gap Versus Offset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Figure 3-40: Modify Setup Flowchart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Figure 3-41: Manual Mode Flowchart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
Figure 4-1: Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-2: Diagnostics Abbreviated Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
-
8/6/2019 Model 1050 Manual
11/170
04/2010 Copyright Exatron, 2010 Figures-3
Figure 4-3: Tape Calibration Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Figure 4-4: Swing Arm Calibration Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Figure 4-5: Getting to HyperTerminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Figure 4-6: Opening the HyperTerminal Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Figure 4-7: Naming a New Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Figure 4-8: Selecting the Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Figure 4-9: Selecting the Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Figure 4-10: Getting to Connection Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Figure 4-11: Getting to ASCII Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Figure 4-12: Displaying Typed Commands Onscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Figure 4-13: Using Call to Connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Figure 4-14: Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Figure 6-1: Brass PSA Rollers (Left); Rubber PSA Rollers (Right) . . . . . . . . . . . . . . . . . . . . . . 6-2
Figure 6-2: Heat Seal Head Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Figure 6-3: Air Regulator Turned Off (Left), On (Right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Figure 6-4: Air Regulator with Small Black Screw Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Figure 6-5: Metal Casing Unscrewed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Figure 6-6: Clear Glass Casing Snapped Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Figure 6-7: Large Black Inner Screw Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Figure 6-8: Solenoid with Plunger on Back Side of Taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Figure 6-9: Sensor Controller Set to L-ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Figure 6-10: Green and Red Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Figure 6-11: Conditions of Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Figure 7-1: Dimensions Listed From Smallest to Largest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
-
8/6/2019 Model 1050 Manual
12/170
Model 1050 Manual
Figures-4 Copyright Exatron, 2010 04/2010
-
8/6/2019 Model 1050 Manual
13/170
04/2010 Copyright Exatron, 2010 1-1
Chapter 1:
Safety and Support
Chapter OverviewThis chapter discusses the following main topics:
Please read and understand this entire manual before installing or using your Exatron taper.
A short glossary of terms used in this manual and other keys to understanding is found at theend of this chapter.
Exatron Safety WarningsTypically, the taper is simply one part of a complete test system. It is the responsibility of thecompany purchasing the taper to properly train all taper operators in all of the safety practicesrequired for every component of the test system.
The following safety procedures must be followed at all times.
Topic Page
Exatron Safety Warnings 1-1
Facilities Requirements 1-2
Installation Overview 1-4
Standard Warranty 1-5
Exatron Support Services 1-6End-of-Life Taper Disposal 1-7
Significance of This Manuals Version Number 1-7
Typographical Conventions Used in This Manual 1-8
Terms Used in This Manual 1-8
WARNING! Keep fingers, hair, and clothing away from any moving parts on the taper. Its
motors are very powerfuland can cause severe injury.
WARNING! Never try to stop an action of the taper with your hands or any other device.To stop, press the Emergency Stop button on the right side of the control box.
-
8/6/2019 Model 1050 Manual
14/170
Model 1050 Manual Chapter 1: Safety and Support
1-2 Copyright Exatron, 2010 04/2010
Using compressed air can be hazardous. It is the responsibility of the company purchasing thetaper to properly train all taper operators in every aspect of the safety practices associatedwith the use of compressed air.
Figure 1-1: Emergency Stop Button
Facilities Requirements
Air Conditioning and Environmental RequirementsThe Model 1050 handler should be installed in a temperature-controlled, dust-free environ-ment to preclude dust and dirt particles from contaminating its moving parts, especially thoseparts which come into contact with the devices being tested. The life of your handler is greatlyenhanced by keeping it as clean as possible. See Chapter 6 for instructions.
There are no special ventilation requirements.
Electrical RequirementsHandlers shipped either within the United States or offshore have built-in switching electricalsupply capability for 100-volt AC to 240-volt AC, 50Hz to 60Hz at 3 amps or less. For moreinformation see "Power Supplies" on page 2-12. Tapers, if included, can be wired for either100-120-volt AC, 60 Hz; or220-240-volt AC, 50 Hzthis must be specified at time of order.
WARNING! Never operate any Exatron system that requires compressed air without anapproved air regulator and shutoff valve, such as that originally supplied with your system.
WARNING! Never unplug a pressurized air hose while the air regulator is turned on.
http://../Handlers--Pick%20n%20Place/900/All%20Docs/900%20Ch%206%20Svc%20n%20Trblshoot.pdfhttp://../Handlers--Pick%20n%20Place/900/All%20Docs/900%20Ch%202%20Description.pdfhttp://../Handlers--Pick%20n%20Place/900/All%20Docs/900%20Ch%202%20Description.pdfhttp://../Handlers--Pick%20n%20Place/900/All%20Docs/900%20Ch%206%20Svc%20n%20Trblshoot.pdf -
8/6/2019 Model 1050 Manual
15/170
Facilities Requirements Vacuum/Pneumatic Requirements
04/2010 Copyright Exatron, 2010 1-3
The power supply is "smart," sensing the voltage in the power line, and matching its poweraccordingly.
If the handler is to be used in an electrically noisy environment or near large electromechani-cal equipment, Exatron recommends the use of a reliable power conditioner to filter line noise,surges, and spikes which can cause the handler to operate improperly or become damaged.
Electricity supplied to the handler must be within the recommended operating range. If the linevoltage drops too low, the handler may not function properly and may be seriously damaged.Verify that correct operating line voltage is present. If it is not, contact Exatron for assistance.
Service calls made to the customer facility to correct problems caused by improperelectrical supply are not covered by the Exatron warranty.
Vacuum/Pneumatic RequirementsThe handler system requires a supply of pressurized air at a minimum of 80 PSI at 2 to 5 CFM(depending on the number of vacuum generators), filtered for proper operation. The air supplymust be clean (containing no particulate matter greater than 5 microns in size), oil-free, anddry (having a dew point of 36 degrees F to 38 degrees F) to operate correctly. Dirty, oily or wetair will cause the vacuum generator to malfunction and will make your system unreliable.
Because the handler is equipped with a taper, add 0.5 CFM of shop air to the CFM requiredfor the handler itself.
The external air source should be attached to the air regulator mounted on the handler base.Before turning on the air regulator and using the handler, make certain the compressed air lineis attached to the air regulator fitting.
To maintain these levels of pressurized air quality, replace the air filter (Exatron part #GPA-97-075) in the air regulator of your handler after every 6000 hours or 12 months of operation,whichever comes first; or if your air regulator registers a pressure drop of 15 PSI.
Moisture of any kind will travel through external and internal air lines. This moisture will coatthese air lines and the insides of the handler's cylinders, causing them to stick or to stop func-tioning altogether. The best defense against this kind of contaminate is to prevent it from
occurring in the first place by maintaining the clean air supply described above.
If the air lines are allowed to become discolored or the moisture traps become overfilled, dam-age to the system will occur. The only corrective action to take at that point is to replace all ofthe air lines and to completely clean all of the solenoids supplied by those air lines. Handlerdamage due to improper air supply is not covered by the Exatron warranty.
NOTE: 110V AC at 20 amps is preferred when available.
CAUTION: Connect the power cord to earth-grounded power outlets only.
-
8/6/2019 Model 1050 Manual
16/170
Model 1050 Manual Chapter 1: Safety and Support
1-4 Copyright Exatron, 2010 04/2010
Air ConnectionsLocated on the lower right side of the main frame supporting the Model 5000 is an air regula-tor with a pressure gauge and a filter. Before turning on the air regulator and using the Model5000 handler and 1050 taper, make certain that a compressed air line of 80 PSI is attached tothe air regulator fitting.
The Model 1050 taper takes its air supply from a 1/4" diameter flexible plastic air line pluggedinto a compressed air outlet mounted on the right side of the Model 5000 handler's main plate.
Figure 1-2: Air Line Attached to Outlet
Installation OverviewBasic installation of your new Exatron handler and taper will consist of the following majorsteps:
Unpacking the handling equipment and assembling its peripheral parts
Powering up the handler and taper ("Power-Up Procedure" on page 3-16) andrunning Diagnostics sequences (Chapter 4)
Cycling sample tubes of devices
Interfacing the handler to your tester/programmer (Chapter 3)
Uncrating the Handler and TaperThe handler and taper will usually come in a wooden crate which will require some disassem-bly to remove. Please inspect the system when it is removed from the crate for any obviousdamage which may be the result of shipping. Contact Exatron and the shipping companyimmediately if you see any damage.
http://1050%20ch%203%20interfaces.pdf/http://1050%20ch%203%20interfaces.pdf/ -
8/6/2019 Model 1050 Manual
17/170
Standard Warranty Customer In-House Service
04/2010 Copyright Exatron, 2010 1-5
Standard WarrantyAll Exatron products are under warranty for one year from the date of purchase. Exatronagrees to repair any mechanical or electrical assembly, subassembly, or entire unit which failsduring normal use within its first year. The customer agrees to follow the recommended main-tenance procedure as defined in this manual.
Exatron does notwarrant test contactors. Handler test contactors are fragile and may be eas-ily ruined by operator abuse. Exatron uses the finest materials available in our contactordesigns.
Exatron does not warrant the following:
Damage caused by improper packaging of equipment returned to Exatron forrepair
Damage caused by the shipping company
Damage caused by natural catastrophes: flood, fire, earthquake, etc.
Damage caused by equipment connected to improper power line voltages
Damage caused by equipment connected to improper air supply: contaminatedwith oil, water, dirt, etc.
Damage caused by operator abuse or improper practices cautioned against in thismanual
Damage caused by interface hardware not manufactured by Exatron
Damage or malfunction caused by customer modifications
Test contactors
Customer In-House ServiceExcept in the case of laser marking systems, Exatron encourages customer in-house equip-ment service and tries to make in-house service as easy as possible to perform. There are no"Void Warranty" warning stickers on Exatron handlers. By using the built-in diagnostic soft-ware and diagnostic tools, it is usually possible for the operator to isolate a problem quicklyand effect a repair.
The customer is responsible for all cost of in-bound shipping expenses. Standard out-boundshipping expenses will be paid by Exatron. In such cases where the customer requests spe-cific out-bound shipping methods be used, the customer is responsible for all shipping costsand any additional related charges.
-
8/6/2019 Model 1050 Manual
18/170
Model 1050 Manual Chapter 1: Safety and Support
1-6 Copyright Exatron, 2010 04/2010
Offshore Warranty ServiceAn Exatron handler purchased in the United States and then shipped offshore will be war-ranted through Exatron in California. Replacement parts are furnished for a period of one yearfrom date of purchase with the exception of replacement contactors. In most cases, it will notbe necessary to return the worn part from the offshore user location.
To receive offshore service support, the handler must be purchased through your localExatron representative or an extended warranty agreement must be purchased directly fromyour local Exatron representative.
Please supply the following information when requesting offshore service or replacementparts:
The part number(s) required. If the part number is not known, photocopy or take aphoto of the part and fax it to Exatron.
The model number of the taper
The type of device being run by the handler, such as: DIP, SOIC, SOJ, PLCC,LCC, SIP, PGA, PCB, ZIP, etc.
The tapers serial number
The full shipping address
Any special shipping or customs instructions
Method of shipment, such as: Federal Express, UPS, DHL, U.S. Mail, or the nameof your chosen shipping company
In most cases, faxed requests and shipment of replacement parts orders are processed withintwenty-four hours of receipt by Exatron.
Exatron Support ServicesFor factory technical support, you can contact us in several ways.
Call 1-800-EXA-TRON or 1-408-629-7600, between 8:00 A.M. and 5:00 P.M.Pacific time, Monday through Friday.
E-mail us anytime at [email protected].
Fax us at 1-408-629-2832.
When contacting us, please have your Exatron equipment close at hand, along with the fol-lowing information:
The model number of your handler with all its options (taper, tubes, etc.)
-
8/6/2019 Model 1050 Manual
19/170
End-of-Life Taper Disposal Offshore Warranty Service
04/2010 Copyright Exatron, 2010 1-7
The exact wording of any messages that appeared on your handler display.
A description of what happened and what you were doing when the problemoccurred.
A description of how you tried to solve the problem.
End-of-Life Taper DisposalExatron has no time limit on Exatron product support. We will make every effort to repair anyof our products, no matter how old it is. Our never-ending support greatly extends the life ofmany of our products.
Exatron offers trade-in value on any of our products as part of a new Exatron equipment pur-chase. Exact terms are subject to quote at that time. This applies to any used Exatron productas a trade-in on any new Exatron product.
We will service our products even when the product is not purchased directly from Exatron.This makes the resale value of Exatron products high as compared to many of our competi-tors. The customer can sell the product to a third party, used equipment vendor, or online as,for example, on eBay. Exatron will always offer spare parts, service contacts, and rebuilds ofany of our products.
Most of the materials used in the construction of our products can be recycled. When it comestime to finally retire an Exatron product, the customer can ship the product back to Exatron, atthe customers expense, and we will quote the cost to dismantle and recycle the handler. Inmany cases, there is no charge for this service other than any third-party disposal fees asrequired. Whenever possible, reusable components will be offered as a donation to localschools.
Please note that in many cases, Exatron builds systems using major third-party pieces ofequipment. These include lasers, printers, camera inspection, chillers, fume extractors, andother large OEM (original equipment manufacturer) subsystems. Exatron will attempt to pro-vide the same support as best we can for these subsystems. Exact details cannot be deter-mined until the day comes that end-of-life service is required. The customer is free to contactthe OEM directly for its end-of life service policy and then deal directly with that OEM.
Significance of This Manuals Version NumberThe version number on the cover page of this manual indicates three things about the revision
version.
The first number is for complete overhauls and brand new manuals.
The second number is for small section changes and additions.
The third number is for small typo changes.
-
8/6/2019 Model 1050 Manual
20/170
Model 1050 Manual Chapter 1: Safety and Support
1-8 Copyright Exatron, 2010 04/2010
For example, version 2.0.1 would refer to a completely redone manual, which had since had afew typographical changes made. The difference between 2.0 and 2.0.1 would be negligible.However, the differences between version 1.0 and 2.0 would be substantial.
Typographical Conventions Used in This ManualNames of keys on the control panel are enclosed in angle brackets ( < > ), such as:
Press the key and then the key.
Messages displayed on the hardware or software are enclosed in straight quotation marks( " " ), such as:
When the handler has been instructed by the operator to send a new start testpulse to the tester/PC, the message: "ISSUE NEW START" is displayed.
Emphasized words and phrases are displayed in bold and italicized type, such as:
Neveruse oil or lubricant of any kind on solenoids.
Terms Used in This ManualBlow-off A positive air pressure in the vacuum lines, used to break
any residual vacuum between the pickup head and a deviceit was suctioning.
Device A generic term that refers to the chip, package, or other partprocessed by the Exatron handler.
Gap The gap, or pitch, between the leading edge of adjacent tapepockets. This gap is found automatically by the gap sensorwhen you press to select "SET GAP ? YES".
Gap offset, orOffset
The additional distance, measured in tape drive motor steps,the tape must advance after the gap sensor has found theleading edge of a tape pocket until the center of a tapepocket is directly under the center of the swing arms pickuphead. This is a one-time-only advancement of the tape at thebeginning of each run. This distance you must set manuallyfor each tape.
Gap steps The distance, measured in tape drive motor steps, betweenthe leading edge of adjacent tape pockets.
Home position The location that each motor returns to each time the handleris reset.
Sum check The total of the parameter values for all the RAM addressesdisplayed in hex.
-
8/6/2019 Model 1050 Manual
21/170
04/2010 Copyright Exatron, 2010 2-1
Chapter 2:
System Description
Chapter OverviewThis chapter discusses concepts of how your handler works. Following chapters show youhow to put these concepts into practice and carry out procedures. This chapter deals with thefollowing main topics:
This chapter will familiarize you with the various parts of the system hardware, what they do,and how they work. Exatron recommends that you read this part of the manual in the pres-ence of the system to facilitate reference to the actual system. The parts of the system areidentified as shown in this chapter.
Topic Page
Key Positions 2-2
How the Model 1050 Works 2-3
Identifying Major Parts 2-3
Communication Between Handler and Taper 2-19
-
8/6/2019 Model 1050 Manual
22/170
Model 1050 Manual Chapter 2: System Description
2-2 Copyright Exatron, 2010 04/2010
Key PositionsFigure 2-1 shows all the positions where a device might rest or be deposited during its coursethrough the Model 5000 handler and Model 1050 taper. Everything above the dotted red linebelongs to the 5000 handler and is discussed in the Model 5000 User Manual.
Figure 2-1: Key Device Positions
Top of octoloader gate
Top of index pin
Top of stack pin
Pickup site w/ cover footPickup head
Test site
Pickup head dropoff site
Laser mark siteLaser bottom gate
Shuttle
Top of index pin
Pickup site w/ cover foot
Top of stack pin
Tape
Swing arm
Input track
Output track
Taper input track
-
8/6/2019 Model 1050 Manual
23/170
How the Model 1050 Works Three Reels
04/2010 Copyright Exatron, 2010 2-3
Note that there are two index pins and two stack pinsone set for the handler, and one set forthe taper. However, this should not cause confusion, because the set for the handler is dis-cussed in the Model 5000 User Manual;whereas the set for the taper is discussed in thismanual, the Model 1050 User Manual.
How the Model 1050 WorksEmpty carrier tape is fed on to the tape track from the supply reel, and the tape drive motoradvances the tape.
Each device is dropped by the shuttle down the taper input track. The stack pin is by defaultextended, stopping each device. When a signal is received, the index pin extends to hold theline of waiting devices, the stack pin retracts, and the device drops to the tapers pickup site,where it is held by the cover foot.
As each device is dropped to the pickup site, the swing arm rotates up over the pickup site,and the pickup head attached to the swing arm extends, picks it up, and retracts. The swing
arm then rotates down and the pickup head again extends to place the device in the carriertape pocket. The drive motor advances the tape one pocket and the process is repeated.
A few inches to the left, a group of sensors ensure that each pocket is filled, and that eachdevice lies flat in the pocket. To the left of these sensors, the sealing heads, either thermal orpressure-sensitive, seal the cover tape onto the edges of the carrier tape.
At regular intervals set by the user, the takeup reel motor is activated and the filled tape iswound onto the takeup reel.
Identifying Major Parts
Three ReelsThe supply reel (sometimes made of cardboard) containing the carrier tape is at the right endof the taper. The takeup reel (usually made of plastic) is at the left end.
The supply reel containing the sealing tape is above the sealing area.
-
8/6/2019 Model 1050 Manual
24/170
Model 1050 Manual Chapter 2: System Description
2-4 Copyright Exatron, 2010 04/2010
Figure 2-2: Reels on Taper
The carrier tape is fed in a right-to-left direction from the supply reel, along the tape track andunder the swing arm, past the sealing tape and sealing heads, to the takeup reel. On the topsurface, the pitch or gap sensor detects the hole in the center of the empty pocket, and signals
the position to the swing arm. When the empty pocket intersects the path of the swing arm,the swing arm places a device into the tape pocket.
Figure 2-3: Tape Track with Swing Armat Pickup Site (Left), at Taper (Right)
Supply reel with carrier tape
Output or takeup reel
Supply reel with sealing tape
Tape track
right-to-left direction
Swing arm withpickup head position
Control panel
-
8/6/2019 Model 1050 Manual
25/170
Identifying Major Parts Taper Input Track
04/2010 Copyright Exatron, 2010 2-5
After receiving devices from the swing arm, the filled carrier tape is sealed, either with pres-sure-sensitive sealing tape or heat-sealed cover tape. If pressure is used to seal, the pressureis continuous; but if heat is used to seal, the heat seal heads are pressed against the tape onlyintermittently to prevent burning.
When a specified number of pockets have been filled, the takeup reel motor is activated long
enough to wind the slack tape onto the takeup reel.
The drive gear drives the tape along, with teeth that protrude upward to fit the holes on theside of the carrier tape. The pinch roller on the pressure roller block presses down on the tape,keeping it meshed with the teeth of the drive gear.
Figure 2-4: Other Features of Taper (Model 201)
Taper Input TrackAlthough physically attached to the Model 5000 handler, the taper input track is logically partof the taper, because Model 5000s that do not have the taper do not have the taper inputtrack, either. Rather, they are equipped with 8 output tubes instead of 5.
Heater controller displays
Empty pocket sensor
Track width locking knob
Pressure seal headsHeater fuse
Sensor lights
Override but-ton lights
EMO (emergency stop) button
Pressure roller block
Takeup arm
-
8/6/2019 Model 1050 Manual
26/170
Model 1050 Manual Chapter 2: System Description
2-6 Copyright Exatron, 2010 04/2010
The taper input track is below the shuttle and to the right of the 5 output tubes. Like the inputtrack on the Model 5000 handler, this track also has solenoids that control an index pin, astack pin, and a cover foot.
During a production run, the stack pin is by default extended, restraining the waiting line ofdevices. When the swing arm on the tape-and-reel assembly is ready to move another device,
the index pin is extended between the lowest device in line and the device just above it. Thenthe stack pin is retracted, allowing the lowest device to fall.
The stack pin and cover foot are activated simultaneously to prevent the device from jumpingthe stop block. Thus, when the stack pin retracts to release a device, the cover foot isextended to hold the device at the pickup site momentarily until any bouncing action stops.
Figure 2-5: Index Pin Retracted (Left), Extended (Right)
-
8/6/2019 Model 1050 Manual
27/170
Identifying Major Parts Emergency Stop Button
04/2010 Copyright Exatron, 2010 2-7
Figure 2-6: Cover Foot Retracted From Pickup Site and Stack Pin Extended (Left);
Cover Foot Extended Over Pickup Site and Stack Pin Retracted (Right)
Emergency Stop ButtonThe Emergency Stop button on the taper control box shuts down everything on the taper only,including the heat seal; whereas the Emergency Stop button on the body of the handler stopsall motors. Pressing the tapers Emergency Stop button causes a taper error message to bedisplayed on the control panel. The operator then has the option of aborting the job run, ormaking any necessary adjustments and then selecting the option to continue the run.
Motors
The motors for the swing arm and tape drive are phase motors. The motor driving the swingarm is inside the cylinder box (Figure 2-7).
-
8/6/2019 Model 1050 Manual
28/170
Model 1050 Manual Chapter 2: System Description
2-8 Copyright Exatron, 2010 04/2010
Figure 2-7: Phase Motor Driving Swing Arm
The motor driving the tape drive is located directly behind the tape drive gear adjustmentknob.
Figure 2-8: Tape Drive Motor
The motor driving the takeup reel is inside the housing for the control panel (Figure 2-9).
Tape drive gear
adjustment knob
Tape drivemotor
-
8/6/2019 Model 1050 Manual
29/170
Identifying Major Parts Sensors
04/2010 Copyright Exatron, 2010 2-9
Figure 2-9: Takeup Reel Motor
The sealing heads are driven, not by a motor, but by air solenoids.
SensorsThe sensors for the Model 1050 taper have descriptive names.
The sensors shown in Figure 2-10 through Figure 2-15 are fiberoptic; they come with sensorcontrollers. For more information on the controllers, see "Fiberoptic Photoelectric SensorGuidelines" on page 6-8.
Sensor Name Sensor ID FigureSensor
Controller
Device at Stack Sensor A Figure 2-10, Figure 2-11 yes
Device at Pickup Site Sensor B Figure 2-10, Figure 2-11 yes
Swing Arm Home Sensor 9 Figure 2-18 no
Pickup Head Vacuum Sensor 8 no
Carrier Tape Out Sensor 6 Figure 2-16 no
Empty Pocket Sensor 5 Figure 2-13 yes
Out-of-Pocket Sensor 7 Figure 2-14 yes
Gap Sensor 4 Figure 2-15 yes
Takeup Arm Sensor 3 Figure 2-17 no
-
8/6/2019 Model 1050 Manual
30/170
Model 1050 Manual Chapter 2: System Description
2-10 Copyright Exatron, 2010 04/2010
Figure 2-10: Device at Stack Sensor (A, Top); Device at Pickup Site Sensor (B, Bottom)
Figure 2-11: Device at Stack Sensor (A, Left); Device at Pickup Site Sensor (B, Right)
-
8/6/2019 Model 1050 Manual
31/170
Identifying Major Parts Sensors
04/2010 Copyright Exatron, 2010 2-11
Figure 2-12: Taper Sensors
In Figure 2-12, the track is shown with no tape to clarify the directions the various sensorbeams are aimed. The Empty Pocket sensor, 5, is aimed downward through the hole in anyempty pocket. The Out-of-Pocket sensor, 7, is aimed across the top of the tape, looking forany devices sticking up above the surface of the tape. The Gap sensor, 4, is aimed across thetape. It looks for the gap, where the tape is in a position where the ridge between pockets iseven with the Gap sensors beam so that it is not blocked by the tape.
Figure 2-13: Empty Pocket Sensor (5)
-
8/6/2019 Model 1050 Manual
32/170
-
8/6/2019 Model 1050 Manual
33/170
Identifying Major Parts Sensors
04/2010 Copyright Exatron, 2010 2-13
Figure 2-16: Carrier Tape Out Sensor (6)
Figure 2-17: Takeup Arm Sensor (3) Closed (Left), Open (Right)
-
8/6/2019 Model 1050 Manual
34/170
Model 1050 Manual Chapter 2: System Description
2-14 Copyright Exatron, 2010 04/2010
Figure 2-18: Swing Arm Home Sensor (9, Left); Swing Arm at Home (Right)
The true home of the swing arm is at the Swing Arm Home sensor, not necessarily at thepickup site.
Override ButtonsThe override buttons on the taper plate accomplish the same thing the software can do, but ina more direct way. Either may be used, according to the operators convenience.
Figure 2-19: Tape-and-Reel Override Buttons
NOTE: The action produced by each numbered override button corresponds withthe action produced by the key with the same number in DIAGNOSTICS OUT-PUT CHECK SOLENOID CHECK. See "OUTPUT CHECK: Solenoid Check" onpage 4-11 and "OUTPUT CHECK: Solenoid Toggle Check" on page 4-12.
-
8/6/2019 Model 1050 Manual
35/170
Identifying Major Parts Index and Stack Pins
04/2010 Copyright Exatron, 2010 2-15
Index and Stack PinsDuring a production run, the stack pin is by default extended, restraining the line of deviceswaiting to fall to the pickup site. When the taper is ready to get another device, the index pin isextended between the lowest device in line and the device just above it. Then the stack pin isretracted, allowing the lowest device to fall.
The stack pin and cover foot are activated simultaneously to prevent the device from jumpingthe stop block. Thus, when the stack pin retracts to release a device, the cover foot isextended to hold the device at the pickup site momentarily until any bouncing action stops.
Seal HeadsThe seal heads are pneumatic; they do not use sensors.
Tape-and-Reel Override Buttons
Button Affects Action
8Blue Takeup reel motor When pressed, takeup motor is turned on, winding the tape andtightening tape slack
7Black Pick-and-place head When pressed, pickup head extends (Figure 2-23)
6White Blow-off When pressed, slight positive air pressure is emitted from suctioncup on swing arm to break vacuum between device and suction cup
5Gray Cover foot and stack pin When pressed, cover foot extends and the stack pin (bottom)retracts (Figure 2-6)
4Green Index pin When pressed, the index pin (top) extends
3Orange Customizable button Used for custom applications, if requested by customer
2Yellow Vacuum When pressed, negative air pressure is activated at suction cup onswing arm to form a vacuum between device and suction cup
1Red Seal heads When pressed, seal heads are lowered onto the tape (Figure 2-20,Figure 2-21)
-
8/6/2019 Model 1050 Manual
36/170
Model 1050 Manual Chapter 2: System Description
2-16 Copyright Exatron, 2010 04/2010
Figure 2-20: Heat Seal Heads with Counterbalance Weight
Figure 2-21: Pressure-Sensitive (PSA) Seal Heads with Counterbalance Weight
Swing ArmThe swing arm rotates from the pickup site at the bottom of the taper output track to the tape
pocket underneath its path.
-
8/6/2019 Model 1050 Manual
37/170
Identifying Major Parts Swing Arm
04/2010 Copyright Exatron, 2010 2-17
Figure 2-22: Swing Arm at Pickup Site (Left), at Tape Drop Site (Right)
At the end of the swing arm is attached a pickup head that raises and lowers to place thedevice in the tape pocket. The pickup head had a suction cup attached, which passes a nega-tive or positive air flow that acts as a vacuum or blow-off. The pickup head is pneumatic, con-trolled by air pressure.
Figure 2-23: Pickup Head Retracted (Left), Extended (Right)
-
8/6/2019 Model 1050 Manual
38/170
Model 1050 Manual Chapter 2: System Description
2-18 Copyright Exatron, 2010 04/2010
Figure 2-24: Path and Limits of Swing Arm
SWING = 355maximum
Pickup site SWING HOME = 34maximum
Taper input track
Tape output
SWING = c. 122from pickup site
Swing arm positions
SWING HOME = c. 12at pickup site
-
8/6/2019 Model 1050 Manual
39/170
Communication Between Handler and Taper Swing Arm
04/2010 Copyright Exatron, 2010 2-19
Communication Between Handler and TaperCommunication signals are sent between the Model 5000 handler and the Model 1050 Taperby means of 4 wires. On the 1050 side they are attached to the 5000-A89 front panel PCB. Onthe 5000 side they are attached to the 3000-055 PCB.
In case of a communication glitch, see the diagnostic instructions in "Checking Communica-tion Between 5000 Handler and 1050 Taper" on page 4-19.
Figure 2-25: Communication WiringOn 1050 Side (Left), On 5000 Side (Right)
Figure 2-26: Connection Port for Communication Wiring
-
8/6/2019 Model 1050 Manual
40/170
Model 1050 Manual Chapter 2: System Description
2-20 Copyright Exatron, 2010 04/2010
Figure 2-27: TAPE-346-E1 Wiring Diagram
-
8/6/2019 Model 1050 Manual
41/170
04/2010 Copyright Exatron, 2010 3-1
Chapter 3: Taper Setup
and RAM Listing
Chapter OverviewThis chapter discusses the following main topics:
Topic Page
Mounting the Takeup Reel 3-2
Mounting the Supply Reel 3-2
Adjusting the Carrier Tape Track Width 3-3
Loading the Carrier Tape 3-5
Loading the Sealing Tape 3-8Adjusting Heat Seal Heads 3-12
Adjusting Pressure Seal Heads 3-15
Power-Up Procedure 3-16
Setting Temperature for Heat Seal Heads 3-19
Calibrating Device Position in Tape Pocket 3-24
Beginning a Production Run 3-25
Power-Down Procedure 3-26
Understanding the Control Panel Keys 3-26
Using the Key 3-27
Modifying Setup 3-28Resetting the Count of Devices in Tape 3-33
Displaying the Count of Devices in Tape 3-33
Using Manual Mode 3-34
Changing RAM 3-39
Notes About the RAM Address Listing 3-40
RAM Address Listing 3-42
Hex-Binary Conversion Table 3-47
Decimal-Hex-ASCII Conversion Table 3-48
-
8/6/2019 Model 1050 Manual
42/170
-
8/6/2019 Model 1050 Manual
43/170
Adjusting the Carrier Tape Track Width
04/2010 Copyright Exatron, 2010 3-3
Figure 3-2: Supply Reel Tape Unwound from Top
Adjusting the Carrier Tape Track WidthYou may need to change the carrier tape track width when different sized devices are pro-cessed. This procedure is best accomplished along with the next procedure, "Loading theCarrier Tape" on page 3-5.
Figure 3-3: Carrier Tape Track at Different Widths
This is accomplished using two of three knobs: the track width locking knob, and either of thetrack width adjustment knobs.
Track width adjustment knobs
-
8/6/2019 Model 1050 Manual
44/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-4 Copyright Exatron, 2010 04/2010
The track width locking knob is located below and between the cover tape reeland the takeup reel.
The track width adjustment knobs are located at both ends of the base.
Figure 3-4: Track Width Locking Knob
1. Turn the track width locking knob counterclockwise to loosenit.
2. Turn either the front or back track width adjustment knob to adjust the trackwidth. (They are connected by an internal chain, so they work in tandem.) Thecarrier tape should slide in the track freely but not loosely, and advance easilywithout binding, but also without too much lateral play in the track.
> To make the tape track narrower, turn the knob clockwise.
> To make the tape track wider, turn the knob counterclockwise.
3. At this point, leave the tape track a little wider than necessary and do the follow-ing procedure, Loading the Carrier Tape.
4. When the carrier tape has been loaded and the adjustment is correct, retightenthe locking knob by turning it clockwise.
CAUTION: Loosen the track width locking knob beforeturning the adjustmentknobs to prevent bending and damage to the aluminum parts.
To adjust the width of the carrier tape track:
-
8/6/2019 Model 1050 Manual
45/170
Loading the Carrier Tape
04/2010 Copyright Exatron, 2010 3-5
Loading the Carrier Tape
1. Feed the leading end of the carrier tape (the leader) toward the sealing tapeguide, making sure that the edge of the tape is under the guide at the side ofthe track.
Figure 3-5: Carrier Tape Under Guide At Top Supply End of Track
2. Continue feeding the carrier tape leader under the sealing heads. The sealing
heads should be raised above the level of the carrier tape at this point.
3. When the carrier tape leader in the track reaches the pressure roller assembly,raise the pressure roller arm with your index finger. Slide the keeper pin intothe pressure roller block assembly to hold it in the raised position while youfeed the carrier tape along the track underneath.
To load the carrier tape:
-
8/6/2019 Model 1050 Manual
46/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-6 Copyright Exatron, 2010 04/2010
Figure 3-6: Lifting Pressure Roller Arm and Pushing In Keeper PinTwo Styles
4. Feed the carrier tape under the projecting takeup arm. Insert the carrier tapeleader into the takeup reel according to the manufacturer's specifications. Windthe carrier tape around the takeup reel until it is secured in place. The carriertape should move freely back and forth underneath the takeup arm.
Figure 3-7: Takeup Arm
5. Align the carrier tape with the tape drive gear. Loosen the blue lock nut on thedrive gear assembly. Then you can turn the red adjustment nut to allow thegear to move laterally. Adjust the gear teeth to fit with the backside track of thecarrier tape. Retighten the blue nut. Next turn the gear using the red thumb-screw section of the gear assembly. This should cause the carrier tape toadvance freely towards the takeup reel.
-
8/6/2019 Model 1050 Manual
47/170
Loading the Carrier Tape
04/2010 Copyright Exatron, 2010 3-7
> Turning the red adjustment nut clockwisemoves the teeth and tape to theright, wideningthe tape path.
> Turning the red adjustment nut counterclockwisemoves the teeth andtape to the left, narrowingthe tape path.
Figure 3-8: Tape Drive Gear Adjustment Knob with Blue Locking Knob Unscrewed
Figure 3-9: Gear Adjustment Narrowed (Left); Widened (Right)
-
8/6/2019 Model 1050 Manual
48/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-8 Copyright Exatron, 2010 04/2010
Loading the Sealing Tape
1. Sandwich a roll of sealing tape between the two sealing tape plates, makingsure the roll is snugged around the larger raised circle on the inside (Figure 3-10).
Figure 3-10: Sealing Tape PlatesOutside (Left), Inside (Right)
2. Suspend the reel on the sealing tape supply reel rod in the center of the taperbetween the two blue delrin supply reel adjustment collars (Figure 3-11).
3. Viewing from above, position the sealing tape supply reel centered over the car-rier tape in the carrier tape track. Tighten the adjustment setscrew on eachsupply reel adjustment collar to secure the sealing tape supply reel in this posi-tion on the rod.
4. The sealing tape unwinds from the bottom of the reel in a counterclockwisedirection toward the sealing tape guide assembly.
> For a pressure-sensitive sealing tape, feed the sealing tape to the rightoverboth pins of the sealing tape guide assembly and then under the guideblock to the left (Figure 3-11). Notice that the tape rests on the upper, largerprojecting pin but never touches the lower, smaller projecting pin.
To load the sealing tape:
-
8/6/2019 Model 1050 Manual
49/170
Loading the Sealing Tape
04/2010 Copyright Exatron, 2010 3-9
Figure 3-11: Sealing Tape Threaded to Sealing Tape Guide Assembly for PSA
> For a heat sealing tape, feed the sealing tape to the right underthe lower,smaller projecting pin, then overthe upper, larger projecting pin of the seal-ing tape guide assembly and under the guide block to the left (Figure 3-12).
Figure 3-12: Sealing Tape Threaded to Sealing Tape Guide Assembly for Heat
-
8/6/2019 Model 1050 Manual
50/170
-
8/6/2019 Model 1050 Manual
51/170
Loading the Sealing Tape
04/2010 Copyright Exatron, 2010 3-11
Figure 3-15: Placement in Grooves of Guide Blockof Sealing Tape (Left) and Carrier Tape (Right)
5. Check to make sure the guide block is the right width for the tape you are using.
6. Loosen the two guide block screws.
> If you need to change the guide block, slip the guide rod partway out andreplace the guide block on the rod (Figure 3-16). Then replace the rod in thebracket.
Figure 3-16: Guide Rod Removed from One Bracket
7. Adjust the guide block to fit directly over the carrier tape and sealing tape.
> Push the guide block down so that it is flush against the carrier tape.
-
8/6/2019 Model 1050 Manual
52/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-12 Copyright Exatron, 2010 04/2010
> While holding the thin edge down, tighten the two red adjustment screws onthe guide block assembly (Figure 3-17). The carrier tape should now beinside the outer set of grooves on the guide block.
Figure 3-17: Guide Block Assembly
8. Use light pressure or heat to attach the sealing tape to the carrier tape.
9. Feed the sealing tape under the guide block assembly. Advance the tape until
approximately five inches of sealing tape extends past the sealing heads. Thesealing tape should now be in between the inner set of grooves on the guideblock.
Adjusting Heat Seal HeadsTwo adjustments may need to be done for a pair of heat seal heads: lateral alignment anddownward pressure. Correct lateral alignment assures that the seal heads are on the sealingedges of the tape; correct pressure balances the degree of heat needed to seal without tapedamage.
Adjusting Lateral PositionIf your Model 1010 taper is equipped with heat seal heads, use this procedure to align the lat-eral position of each head separately.
1. Make sure the heaters are off and the thermal heads are cool. There are two
CAUTION: Do not use adhesive tape on the carrier tape, as it contains static elec-tricity and can ruin the static-free condition of the carrier tape.
To align lateral position of heat seal heads:
Guide block adjustment screws
-
8/6/2019 Model 1050 Manual
53/170
Adjusting Heat Seal Heads Adjusting Lateral Position
04/2010 Copyright Exatron, 2010 3-13
readouts for each heater controller display. The top line is the present value(PV) and the bottom line is the set value (SV). Set the bottom line to 0 degrees(see "Setting Temperature for Heat Seal Heads" on page 3-19 for instructions),and wait until the sealing head is at ambient room temperature.
2. Remove the seal head closest to you (the front seal head). Use a #10 size hex
wrench and remove the seal head adjustment screw. Remove the seal headand lay it aside.
3. Loosen the adjustment screw on the back seal head. Adjust the head laterallyso that it is directly over the back edge of the sealing tape.
4. Manually engage the back seal head and confirm that the edge of the seal headis aligned with the back of the sealing tape. Make sure that the track holes onthe carrier tape are not blocked by the sealing tape.
5. With the seal head engaged, tighten the adjustment screw.
6. Repeat this process with the front sealing head.
Figure 3-18: Semicircular Seal Head with Adjustment Screw
7. Once both heads are aligned, turn the heat to the sealing heads on. Note thatyou must power on the handler and the taper in order to do this. (See "Power-
Up Procedure" on page 3-16.) Set the bottom line (the Set Value) on both heat-ers to 350 degrees. (For instructions on changing the Set Value, see "SettingTemperature for Heat Seal Heads" on page 3-19.) Wait until the top line (thePresent Value) reads 350.
8. After the sealing heads have warmed up, check the seal on the sealing tape.
WARNING: Do not touch the heat seal heads directly when the heat is turned on.
Adjustment screw
-
8/6/2019 Model 1050 Manual
54/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-14 Copyright Exatron, 2010 04/2010
Manually engage both seal heads. Apply pressure to the sealing tape for 3 to 5seconds. Use the takeup arm to engage the heads. This should cause a goodseal to the carrier tape. Manually advance the carrier tape and inspect the seal.
9. Run the carrier tape for several pockets with the seal heads engaged.
Figure 3-19: Example of Good Tape Seal
Adjusting Downward PressureTo balance the heat temperature with the pressure applied, you may want to adjust the pres-sure of the heat seal heads.
If more pressure is needed to allow a lower heating temperature, add a heavierweight to the counterweight bar (Figure 3-20).
NOTE: You may need to practice this adjustment a few times by running themachine briefly at the start of a job and inspecting the seal for quality.
To adjust pressure of heat seal heads:
-
8/6/2019 Model 1050 Manual
55/170
Adjusting Pressure Seal Heads Adjusting Downward Pressure
04/2010 Copyright Exatron, 2010 3-15
Figure 3-20: Three-Gram and One-Gram Weights (Left); One-Gram Weight on Heat Seal Counterbalance
Adjusting Pressure Seal HeadsTwo adjustments may need to be done for a pair of pressure seal heads: the lateral alignmentof the rollers, and the weights that cause downward pressure. Correct lateral alignmentassures that the seal heads are on the sealing edges of the tape; correct pressure assures agood seal.
Figure 3-21: Pair of Pressure Seal Heads with Lateral Adjustment Screws
To move either pressure seal head laterally, loosen the adjustment screw and pull or push thehead to the correct position. Retighten the screw when the adjustment is correct.
Lateral adjustment screws
-
8/6/2019 Model 1050 Manual
56/170
-
8/6/2019 Model 1050 Manual
57/170
Power-Up Procedure Adjusting Downward Pressure
04/2010 Copyright Exatron, 2010 3-17
Figure 3-23: Air Regulator Turned Off (Left), On (Right)
3. Ensure that the programmer/tester is properly docked to the back of the han-dler. Verify that the programmer/tester is installed with the correct "Pin 1" orien-tation.
4. Verify that the proper changeover kit is installed on the handler. Check theseparts:
> Octoloader input tube holder plate
> Main test site rail assembly
> Correct size plunger bar
> Shuttle assembly (may be insert only)
> Proper extruded aluminum output tubes or output tube holder with plastictubes
5. Move the octoloader plate so that it is flush against the octoloader home switch.
6. Place tubes of devices into the octoloader.
CAUTION: Do not run the handler with the programmer/tester undocked. If you do,the handler will release parts out of the test site onto the floor.
On/off switchin ON position
Adjustment valve
On/off switch inOFF position
-
8/6/2019 Model 1050 Manual
58/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-18 Copyright Exatron, 2010 04/2010
7. Place empty output tubes into the output tube holder.
You are now ready to power up the Model 5000 handler.
1. Turn on the handlers power supply by twisting the red Emergency Stop buttonclockwise on the power supply until it pops out. (Figure 3-24)
Figure 3-24: Emergency Stop Button on Model 5000 Handler
> As the handler powers up, its control panel displays its opening messages.At the end, it displays the message "READY TO RUN." See the Model 5000User Manualfor further power-up information on the handler.
You are now ready to power up the Model 1050 taper.
1. Turn on the tapers power supply by twisting the red Emergency Stop buttonclockwise on the power supply until it pops out.
CAUTION: Make sure all output tubes are empty at the beginning of a run. If youbegin a run with devices in an output tube, the count will be off, and the handlermay try to overfill the tube, jamming devices.
To power up the handler:
NOTE: For thermal tape systems, powering on the Model 1050 also turns on theheaters in the sealing heads.
To power up the taper:
-
8/6/2019 Model 1050 Manual
59/170
Setting Temperature for Heat Seal Heads Adjusting Downward Pressure
04/2010 Copyright Exatron, 2010 3-19
Figure 3-25: Emergency Stop Buttons for Both Handler and Taper
> As the taper powers up, it displays a list of messages like the following, withits model and current control program with revision date. (Please give thisrevision date to Exatron's Customer Service Department when calling forassistance or software updates. Exatron offers free firmware updates onrequest for the life of the equipment.)
V02.14 Test Ok
EXATRON TAPE
TAPE-2 11-16-05
MOD SET UP ? NO
FIND MOTOR HOME
HOME SWING HEAD
MOTOR HOME
TAKE UP MOTOR ON
READY TO RUN ?
Setting Temperature for Heat Seal HeadsThe red/orange temperature readouts in the lower SV (Set Value) display are the desired tem-peratures. The green temperature readouts in the upper PV (Present Value) display are the
actual or current temperatures. The front sealing head is the one nearest you as you stand infront of the taper.
E-Stop button forModel 1050 taper
E-Stop button forModel 5000 handler
-
8/6/2019 Model 1050 Manual
60/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-20 Copyright Exatron, 2010 04/2010
Figure 3-26: Heater Controller Display
In Figure 3-26, the back heat seal head has been set to 350 degrees, and the current temper-ature is 347 degrees.
When the seal head is heating, the green LED light to the left of the Set Value display is on.When the present temperature is stable, the orange LED light to the left of the Present Valuedisplay is on.
A general guideline may be to use somewhere around 275 to 325 degrees Fahrenheit (or 135to 165 degrees Celsius) for a heat seal. If in doubt, it is better to start with a lower temperatureand test the result, then increase little by little as needed. A narrow carrier tape takes a
lower temperature to prevent burning.
This example changes the set temperature from 0 degrees to 275 degrees.
1. Press the SET button on the lower left of the temperature control display (Fig-ure 3-27).
> The lower display blinks rapidly, indicating it is ready to be set.
NOTE: It should not take more than 2-3 minutes to heat the seal heads to the SetValue. If it takes longer, the Set Value may be too high.
To set the temperature:
Present Value temperature
Set Value temperature
-
8/6/2019 Model 1050 Manual
61/170
-
8/6/2019 Model 1050 Manual
62/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-22 Copyright Exatron, 2010 04/2010
Figure 3-30: Left Arrow Button
4. Press the Up arrow button repeatedly until the 0 changes to 7 (Figure 3-31).
Figure 3-31: Digit in Tens Position Selected
5. Press the Left arrow button to shift the digit that lights up to the hundreds digit.
6. Press the Up arrow button repeatedly until the 0 changes to 2 (Figure 3-32).
Figure 3-32: Temperature Set Before the SET Button Is Pressed
7. Press the SET button again. All the set value digits stop blinking and light up in
-
8/6/2019 Model 1050 Manual
63/170
Setting Temperature for Heat Seal Heads Adjusting Downward Pressure
04/2010 Copyright Exatron, 2010 3-23
a steady display, and the temperature (PV) increases rapidly.
Figure 3-33: Temperature Set After the SET Button Is Pressed
8. Repeat the procedure for the other seal head.
1. Press the SET button on the lower left of the temperature control display.
> The lower display blinks rapidly, indicating it is ready to be set.
2. Press the Down arrow button until the ones value is 0 (Figure 3-34).
Figure 3-34: Down Arrow Button
3. Press the Left arrow button to shift the digit that lights up to the tens digit.
4. Press the Down arrow button until the tens value is 0.
5. Press the Left arrow button to shift the digit that lights up to the hundreds digit.
6. Press the Down arrow button until the hundreds value is 0 (Figure 3-35).
To turn off the heat seal heads:
-
8/6/2019 Model 1050 Manual
64/170
-
8/6/2019 Model 1050 Manual
65/170
Beginning a Production Run Adjusting Downward Pressure
04/2010 Copyright Exatron, 2010 3-25
Figure 3-36: Tape Calibration Needed
> If the swing arm places the device to one end of the pocket or betweenpockets, the tape position needs to be calibrated. Follow the instructions in"ALL MOTOR CHECK: Drive Motor Check" on page 4-13.
Figure 3-37: Swing Arm Calibration Needed
> If the swing arm places the device to one side of the pocket or the other, theswing arm needs to be calibrated. Follow the instructions in "ALL MOTORCHECK: Swing Arm Check" on page 4-14.
Beginning a Production RunBefore beginning a production run, make sure that first the handler and then the taper arepowered up, as described in "Power-Up Procedure" on page 3-16.
1. Press the key on the handlerscontrol panel.
2. Press the key on the taperscontrol panel.
> The tapers control panel message changes from "READY TO RUN ?" to
"WAITING." When enough devices are stacked in the tapers input track, thetaper will begin transferring the devices to the tape automatically. No furtheraction is needed by you.
To begin a production run:
-
8/6/2019 Model 1050 Manual
66/170
Model 1050 Manual Chapter 3: Taper Setup and RAM Listing
3-26 Copyright Exatron, 2010 04/2010
Power-Down ProcedureIn case of unexpected events, you can push in the Emergency Stop button to turn off thepower to the taper at any time.
1. Run the handler until empty of all devices. Finish the current job.