MAXIMOPanel formwork with the one-sided MX tie technology
Edition 03 | 2014
PERI GmbHFormwork Scaffolding EngineeringRudolf-Diesel-Strasse 1989264 WeissenhornGermanyTel. +49 (0)7309.950- 0Fax +49 (0)7309.951- [email protected]
Important Notes
Without exception, all current safety regulations and guidelines must be observed in those countries where our products are used.
The photos shown in this brochure feature construction sites in progress. For this reason, safety and anchor details in particular cannot always be considered as conclusive or final. These are subject to the risk assess-ment carried out by the contractor.
The systems or items shown may not be necessarily available in every country.
Safety instructions and load specifications are to be strictly observed at all times. Separate structural calculations are required for any deviations from the standard design data.
The information contained herein is subject to technical changes in the interests of progress. Errors and typo-graphical mistakes reserved.
Content
MAXIMO 3 Panel formwork with the one-sided MX tie technology
Faster tie installation 4 The one-sided installation technology with the MX 15
and MX 18 formwork ties
6 Completely without spacer tubes and cones
Fewer ties 8 Optimized arrangement of the tie points
Improved concrete finish 10 Neat joint and tie arrangement
Project examples 12 The optimal system for all requirements
Standard applications 14 Panel connections, wall connections, T-junctions 15 Corners, wall offsets 16 Stopend Formwork 17 Longitudinal compensation, oblique angles
Supplementary System Components 18 Inside Corner MXI 60/60 19 Tension and Compression Brace 20 Shaft Corner MXSE
Closure technology 22 Systematic solutions for every single application
24 Components overview MX 15
2
3
MAXIMOPanel formwork with the one-sided MX tie technology
In spite of less site personnel, MAXIMO is significantly faster than conventional panel formwork. The one-sided tie installation by only one man reduces costs and also opens up new possibilities to realize visible concrete surfaces using panel formwork.
It is fully compatible to the proven TRIO system and fulfils the highest requirements regarding cost- effectiveness and achievable quality of workmanship. All outstanding advantages of the TRIO, e.g. few different panel sizes and the BFD alignment coupler as the only connecting part, were retained for the development of the MAXIMO.
■Faster tie installation through the one-sided tie tech-
nology without spacer tubes and cones.
■ Fewer ties through the optimized tie point
arrangement.
■ Improved concrete finish through the neat joint and tie
arrangement.
4
Faster tie installationThe one-sided installation technology with the MX 15 and MX 18 formwork ties
Tie System MX 15(Perm. load of the tie rod: 90 kN)
MX 15 Ties 15 – 25for wall thicknesses 15 / 17.5 / 20 / 22 / 24 / 25 cmMX 15 Ties 20 – 30for wall thicknesses 20 / 22 / 24 / 25 / 30 cmMX 15 Ties 30 – 40for wall thicknesses 30 / 35 / 36 / 40 cm
Assembly sequenceUnique preparation phase
Tie System MX 18(Perm. load of the tie rod: 120 kN)
MX 18 Ties 15 – 25for wall thicknesses 15 / 17.5 / 20 / 22 / 24 / 25 cmMX 18 Ties 20 – 30for wall thicknesses 20 / 22 / 24 / 25 / 30 cmMX 18 Ties 30 – 40for wall thicknesses 30 / 35 / 36 / 40 cmMX 18 Ties 40 – 50for wall thicknesses 40 / 45 / 50 cmMX 18 Ties 50 – 60for wall thicknesses 50 / 55 / 60 cm
Position the Wingnut MX at the primary formwork panel and tighten the eye bolt.
Push the MX Tie through the closing formwork into the wingnut of the primary formwork and screw in.
Set out the required wall thickness at the tie by means of a cotter pin, and counter lock with nut. The usual wall thicknesses are indicated through markings on the tie rod.
Repetitive tie steps
5
As an alternative to the MX tie tech-nology, the conventional DW 15 and DW 20 systems can also be used.
NoteThe programme overview in this brochure features the system components for the use of the Tie MX 15. The corresponding programme overview for the Tie MX 18 is available on request.
Tighten the eye bolt.Tighten the MX Tie using the MX Tie Rod Spanner until the eye bolt can be attached.
Tighten the MX Tie with the MX Tie Rod Spanner as far as the stop position.
The opening of the frame allows deviations of the tie rod angle of up to 4°. In concrete terms this means an inclined position of up to 3.8 cm for a 30 Panel. As a result an installation of ties is possible without any problems if, for example, the bottom slab is uneven as it is commonly experienced on jobsites.
approx. 3.8 cm
30 cm
6
Faster tie installationCompletely without spacer tubes and cones
The conical tie rod requires no spacer tubes and cones. This allows tie operations on the side of the closing formwork.
As a result, only one man is needed; apart from this, guardrails are not necessary at intermediate levels on the primary formwork. In addition, the required working space between the primary formwork and, for example, adjacent buildings or sheet piling, is considerably reduced.
In comparison, two men and clearly more working steps are required when using conventional panel formwork:
■close unused tie holes■screw wingnut counterplate onto
the DW tie rod■ insert tie■attach cone 1■cut spacer tube to size■slide on spacer tube■attach cone 2■ insert tie■screw wingnut counterplate onto
the DW tie rod■secure wingnut counterplate with
a hammer
The MX Removable Sealing
The sealing sleeve used with the MX Removable Sealing reliably closes the tie point when using the MX Tie and thus prevents any concrete bleeding. This also applies with an inclined tie position of up to 4°. In addition, the tie hole is protected by a metal ring against all impacts.
Exchanging the removable sealing from MX 15... ... to MX 18. This can be carried out easily and quickly on the construction site.
7
Working scaffold is not requiredDue to the fact that ties are installed from one side only, ad-ditional safety measures, e.g. working scaffold on the primary formwork, are not required which saves both time and money. This is of great importance particularly for high formwork.
8
Fewer tiesOptimized arrangement of the tie points
Panel grid arrangement 30 cmMAXIMO panels are available in 6 heights from 30 cm up to 3.30 m as well as 5 widths from 30 cm to 2.40 m in 30 cm increments. In addition, a 45 cm wide panel is available which greatly reduces the use of filler plates.
With MAXIMO, the tie points on all panel sizes are centrically arranged. Every tie hole is used and edge ties are not required.
There are no unused tie points that have to be closed. This eliminates pos-sible sources of error and reworking at tie points affected by concrete bleed-ing. At the same time, tie points with MAXIMO are reduced by up to 40 %. This has – apart from the time advan-tages due to the one-sided MX tie technology – a positive impact on the performance factor.
Panel connections with the Align-ment Coupler BFDThe Alignment Coupler BFD ensures tight panel joints resulting in an excellent concrete finish. With only one compo-nent, every panel connection is flush, aligned and tight.
9
240 120 90 60 45 30
30
60
90
120
270
330
Width
Height
10
Improved concrete finishNeat joint and tie arrangement
Creating concrete surfaces:systematically, cost-effectively, easily.
Realizing special wall surfaces with very little extra effort using an efficient panel formwork system is a frequent request of clients and architects. The centrally-arranged tie points in the MAXIMO panel formwork results in a regular joint pattern – horizontally and vertically. Due to the fact that various panelcom-binations can be selected, this opens a range of flexible design options – which can be realized very cost-effectively.
Concrete surface design with the MX grid arrangement
The defined arrangement of indi-vidual MAXIMO panels in a so-called “MX grid” facilitates the creation of attractively-designed visible concrete finishes. The number and position of the tie points is constant in the variants shown here.
The clearly defined arrangement of the individual MAXIMO panels in so-called “MX grids” facilitates the visually appealing design of concrete surfaces with a clean concrete surface, no impressions created by unused tie points and free of concrete bleeding at unsealed tie points.
11
12
Project examplesThe optimal system for all requirements
Regular joint and tie arrangement on visible wall surfaces.Outlet Centre Business Complex, Metzingen, Germany
Short construction period – high level of safety.MAXIMO and PROKIT side mesh barriers at concreting brackets.Single-family house cellar, Weissenhorn, Germany
Extending theSchneefernerhaus Environmental Research Station, Zugspitze Mountain.
13
MAXIMO being climbed on Folding Platforms FB 180.Siemens Logistics Centre in Frankfurt
High, visible wall surfaces.Rehabilitation Centre, Stuttgart-Fellbach, Germany
A triple extension, moved as a complete unit and requiring no working scaffold on the opposite side.Rehearsal stage at the Staatstheater, Stuttgart, Germany
MAXIMO for high, inclined walls in combination with SKS climbing brackets. Congress Centre am Schlossberg,Heidenheim, Germany
In addition to the requirement of being able to be used flexibly as well as efficiently on the construction site for all those components to be constructed, MAXIMO also fulfils the requirement to create the remaining visible concrete surfaces in high quality through the skilful selection and arrangement of the panels.
14
60
6060
6060
6060
60
MX
I 50/
20
MX
I 50/
20
MX
I 50/
20M
XI 5
0/20
MX
I 50/
20M
XI 5
0/20
MX
I 50/
20
MX
I 50/
20
20 244/5
10
254030
240
240
240
240
Standard applicationsPanel connections, wall connections, T-junctions
Panel connections Wall connections
Alignment Coupler BFDItem no. 023500
T-JunctionsWall thicknesses 15 – 40 cm
Internal formworkInside Corner MXI 50/203 x Alignment Coupler BFD
External formworkPanel MX 602 x Alignment Coupler BFD
Adapting to the wall thickness with Wall Thickness Compensator MX or timber.3 x Alignment Coupler BFD
15
MXA 45 MXA 45 MXA 45240 / 45 / 30
240 / 45 / 30
45
MXI 50/20
MXI 50/20
MXI 50/20
MX
I 50/
20
MX
I 50/
20
MX
I 50/
20
MXA 45
MXA 45
MXI 50/20
45
45
30
3045
240 / 45 / 30 240 / 45 / 30
240 / 45 / 30240 / 45 / 30
20 24/25 30
Corners, wall offsets
Corners with MXI 50/20Wall thicknesses 15 – 40 cm
Internal formworkInside Corner MXI 50/203 x Alignment Coupler BFD
External formworkOutside Corner MXA 45Panel MX 304 x Alignment Coupler BFD
No tie is required at the short side of the Internal Corner MXI 50/20.
Wall offsets
20 – 28 cm■ Inside Corner MXI 50/20■ Panel MX 45■ Compensation Waler MAR 170■ Compensation Waler MAR 85■ filler timber supplied by contractor
65 – 79 cm■ Inside Corner MXI 50/20■ Outside Corner MXA 45■ Panel MX 30■ Compensation Waler MAR 170 with 1 Hook Tie DW 15 and Wingnut Pivot Plate■ Compensation Waler MAR 85 with 1 Hook Tie DW 15 and Wingnut Pivot Plate■ filler timber supplied by contractor
16
Standard applicationsStopend Formwork
Stopend Formwork
Using a conventional solution3 x Compensation Waler MAR 85-2 at a height of 2.70 m.
With TRIO Stopend Panel MT/MTFFor continuous reinforcement, with or without water bars.
■ Time savings min. 40%.■ No damage to the formlining.
Centre Section MTF, with water bar
Centre Section MT, without water bar
17
135°
2 4 7
1 6
1 6
3 5 8
1 6
1 6
75°
1
2
3
4
5
6
7
8
Longitudinal compensation, oblique angles
Length compensations
Up to 10 cmWith Wall Thickness Compensator MX or timbers and Alignment Coupler BFD.
10 cm to 36 cmWith Filler Support TPP and formlining.TPP 270, Item no. 101813TPP 120, Item no. 101823
External formworkArticulated Corner MX outsidePanel MXM 60Panel MX 45 and MX 30 at 75°
Internal formworkArticulated Corner MX insidePanel MX 45Panel MX 30 at 75°
External: 3 x BFD 2 x SRU 122Internal: 2 x BFD
= number of struts
External: 3 x BFD 2 x MAR 85Internal: 2 x BFD
Oblique angles
18
30
30
30
30
4545
60
MXi 60
MXA 45
MXI 60
45
Supplementary System ComponentsInside Corner MXI 60/60
T-JunctionsWall thickness 15 – 40 cm
Internal formwork■ Inside Corner MXI 60/60■ 3 x Alignment Coupler BFD
External formwork■ 2 x Panel MX 45■ 1 x Panel MX 60■ 3 x MAR 170-2■ 2 x Alignment Coupler BFD
The Inside Corner 60/60 is used for architacturally-designed con-crete surfaces, continuous joint and tie arrangements that reach right up into the corners, or when using the Sealing Cone MX 55 to close the tie points.
CornersWall thickness 15 – 40 cm
Internal formwork■ Inside Corner MXI 60/60■ 3 x Alignment Coupler BFD
External formwork■ Outside Corner MXA 35 or 45■ 2 x Panel MX 45■ 4 x Alignment Coupler BFD
19
Tension and Compression Brace
Foundations/ upturn beams■ Only a minimum of working space is
required.■ Water stop metal strips are no hin-
drance.
The middle tie point brings decisive advantages when forming founda-tions, parapets and beams.
By using of the tension and compression brace in connection with the middle tie of the MAXIMO panel, a bottom row of ties is not necessary.
Two lengths are available:The Tension and Compression Brace MX 15-40 is continuously adjustable in 5 cm increments from 40 cm onwards; the MX 15-100 accordingly up to 100 cm.
Beams■ Thick reinforcement is not a problem.
Parapets or other similar structural components
20
Supplementary System ComponentsShaft Corner MXSE - for fast moving of the complete internal shaft formwork
The MAXIMO Shaft Corner MXSE is a 90° inside corner which also serves as a striking panel.
One panel with two functions:– for forming the inside corner– for striking complete internal shaft
formwork units.
When releasing the shaft corners and pulling with the crane, a 35 mm striking clearance is created in the corner area.
■ Quick and safe handling Striking takes place requiring very few
working steps - without spindles and from the ground. Assembly on the next panel is carried out with the Alignment Coupler BFD.
■ Formlining right up into the corner Nailable formlining is installed over
the entire surface of the MXSE Shaft Corner. This means that mounting parts can also be securely fixed to the formwork in the corner areas.
■ Moving complete units The MXSE Shaft Corners, together
with the wall formwork elements, form a complete formwork unit for all concreting cycles. BFD Alignment Couplers bridge all required compen-sations. The MX Wingnuts also remain attached to the panels.
35 mm striking clearance for easy striking.
The Shaft Corner MX is available in heights of 330, 270 and 120 cm.
■ Shaft dimensions from 1.30 x 1.30 m
With the Shaft Corner MXSE, ground plans of 1.30 m x 1.30 m upwards can be formed. The maximum shaft dimension and resp. formwork height is limited by the 2.0 t load-carrying capacity of the lifting unit.
Shuttered Struck
min
. 1,3
0 m
Lifting with the crane results in a 35 mm striking clearance on each side.
Lifting the striking mechanism with a crowbar in order to release the formwork from the concrete. It is subsequently attached to the crane.
35 mm
21
22
Closure technologySystematic solutions for every single application
Deep installationInstall flush with the surfaceOnly as a visual functionSealing against non-pressing waterSealing against pressing waterWalls with sound protection functionWalls with Fire-Resistance Class F90Used for attractively designed visible concrete surfacesShadow joint
Deep installationInstall flush with the surfaceOnly as a visual functionSealing against non-pressing waterSealing against pressing waterWalls with sound protection functionWalls with Fire-Resistance Class F90Used for attractively designed visible concrete surfacesShadow joint
■
■
Plug MX Ø 17.5-22
No cone required
Tie MX 15
Tie MX 18DK Concrete Cone
DW 15-58/30
Magnets are fitted in the cone which means they are reliably fixed to the metal ring of the sealing integrated in the panel.
Magnet Cone MX 15-55
■
■
■
■
Plug MX Ø 24-28
No cone required
23
■
■
■
■
Stopper MX 15 – 50
OF – LS
For use with Spacer Tube, Rough DR 22 or Concrete Spacer Tube FZR. Covers the sealing on the panel.
■
■
■
■
Plug DR 22
Plug FRZ 22
For use with Spacer Tube DR 28 and DR Concrete Cone UNI 58/52.
■
■
■
DK Concrete Cone UNI 58/52
Magnets are fitted in the cone which means they are reliably fixed to the metal ring of the sealing integrated in the panel.
Tie MX 15
DW 15Tie MX 18 DW 20
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Stopper MX 15 – 50
MF – LS
Stopper MX 15 – 75 MF – LMX 15 – 75 MF – S
DK Concrete Cone DW 15-58/30
DK Concrete Cone Archi-tectural/01 DW 15-58/52
DK Concrete Cone UNI 58/52
No cone required
Magnet Cone MX 15 -55
Magnets are fitted in the cone which means they are reliably fixed to the metal ring of the sealing integrated in the panel.
Magnet Cone MX 15-55
■
■
■
■
■
■
■
DK Concrete Cone Archi-tectural/01 DW 15-58/52
DK Concrete ConeUNI 58/52
MAXIMO MX 15 Panel Formwork
24
Item no. Weight kg
114258 172.000 Panel MX 330 x 902.970 m². Panel with 18 mm plywood.
1200
1200
450
900450 450 120
450
3300
114248 226.000 Panel MX 330 x 1203.960 m². Panel with 18 mm plywood.
3300
450
1200
1200
450
600 600
1200
120
114426 408.000 Panel MX 330 x 2407.920 m². Panel with 18 mm plywood.
3300
2400
120
1200
450
1200
1320 540540
450
MAXIMO MX 15 Panel Formwork
25
Item no. Weight kg
114457 79.500 Panel MX 330 x 300.990 m². Panel with 18 mm plywood.
150 150300
3300
1200
1200
450
450
120
114452 99.800 Panel MX 330 x 451.485 m². Panel with 18 mm plywood.
1200
1200
450120225 225
450
450
3300
114445 118.000 Panel MX 330 x 601.980 m². Panel with 18 mm plywood.
300 300
600
450
1200
1200
450
3300
120
MAXIMO MX 15 Panel Formwork
26
Item no. Weight kg
114470 206.000 Inside Corner MXI 330 x 603.960 m². Panel with 18 mm plywood. For 90° internal corners.
1200
450
1200
450
3300
600
120
480
115338 136.000 Inside Corner MXI 330 x 50/202.310 m². Panel with 18 mm plywood. For 90° internal corners.
Complete with12 pc. 124895 PVC Plug MXM 15 Ø 18.3
450
450
3300
200
500
120
1200
1200
114464 141.000 Multi Panel MXM 330 x 601.980 m². Panel with 18 mm plywood. For oblique angles, wall connections etc.
Complete with33 pc. 124895 PVC Plug MXM 15 Ø 18.3
100 10 x 40 = 400 100
450
450
1200
1200
3300
120
600
MAXIMO MX 15 Panel Formwork
27
Item no. Weight kg
114486 170.000 Outside Corner MXA 330 x 352.310 m². Panel with 18 mm plywood. For 90° external corners.
350
3300
120
114478 192.000 Outside Corner MXA 330 x 452.970 m². Panel with 18 mm plywood. For 90° external corners.
450
120
3300
117913 401.000 Shaft Corner MXSE 330Panel for forming 90° inside corners along with striking and moving complete internal shaft form-work units.
Technical DataPermissible load-bearing point capacity 2.0 t.
450
1200
450
3300
120
480 60
0
1200
MAXIMO MX 15 Panel Formwork
28
Item no. Weight kg
114842114826114846114394
17.800 18.900 20.200 12.100
Wall Thickness Compensations WDA MX 330Wall Thickness Comp. WDA MX 330 x 4Wall Thickness Comp. WDA MX 330 x 5Wall Thickness Comp. WDA MX 330 x 6Wall Thickness Comp. WDA MX 330 x 10, AluFor adjusting to wall thicknesses.
B 40 50 60 100
3300
B 60
120
100 62
120
114607 51.100 Articulated Corner MXGA 3300.990 m². Made of aluminium, for oblique angles from 75° upwards, external.
150 150
120
3300
114583 88.800 Articulated Corner MXGI 3301.980 m². Made of aluminium, for oblique angles from 75° upwards, internal.
3300
300 300
120
MAXIMO MX 15 Panel Formwork
29
Item no. Weight kg
112006 336.000 Panel MX 270 x 2406.480 m². Panel with 18 mm plywood.
2700
540
2400
1201320 540
1500
600
600
116454 446.000 Panel MX 330 x 2708.910 m². Panel with 18 mm plywood.
270033
001201500600 600
450
1200
1200
450
101829 9.820 Filler Profile TPP 330, AluFor compensation with 21 mm filler plates.
3300
5160
98
MAXIMO MX 15 Panel Formwork
30
Item no. Weight kg
112200 104.000 Panel MX 270 x 601.620 m². Panel with 18 mm plywood.
2700
600120300 300
1500
600
600
112045 135.000 Panel MX 270 x 902.430 m². Panel with 18 mm plywood.
600
1500
600
2700
450 450900
120
112022 186.000 Panel MX 270 x 1203.240 m². Panel with 18 mm plywood.
600
1500
600
2700
600 600
1200
120
MAXIMO MX 15 Panel Formwork
31
Item no. Weight kg
112849 108.000 Multi Panel MXM 270 x 601.620 m². Panel with 18 mm plywood. For oblique angles, wall connections etc.
Complete with22 pc. 124895 PVC Plug MXM 15 Ø 18.3
600
1500
600
2700
100 40010 x 40 = 100
600
120
112090 62.800 Panel MX 270 x 300.810 m². Panel with 18 mm plywood.
2700
300120
600
1500
600
150 150
112078 77.500 Panel MX 270 x 451.215 m². Panel with 18 mm plywood.
2700
450120
1500
600
600
225 225
MAXIMO MX 15 Panel Formwork
32
Item no. Weight kg
117914 305.000 Shaft Corner MXSE 270Panel for forming 90° inside corners along with striking and moving complete internal shaft formwork units.
Technical DataPermissible load-bearing point capacity 2.0 t.
600
1500
600
2700
120
480 60
0
112419 155.000 Inside Corner MXI 270 x 603.240 m². Panel with 18 mm plywood. For 90° internal corners.
1500
600
600
2700
120
600
480
115255 103.000 Inside Corner MXI 270 x 50/201.890 m². Panel with 18 mm plywood. For 90° internal corners.
Complete with8 pc. 124895 PVC Plug MXM 15 Ø 18.3
200
500
600
600
2700
120
1500
MAXIMO MX 15 Panel Formwork
33
Item no. Weight kg
113203 69.400 Articulated Corner MXGI 2701.620 m². Made of aluminium, for oblique angles from 75° upwards, internal.
2700
300 300
120
112667 141.000 Outside Corner MXA 270 x 351.890 m². Panel with 18 mm plywood. For 90° external corners.
2700
350
120
112806 159.000 Outside Corner MXA 270 x 452.430 m². Panel with 18 mm plywood. For 90° external corners.
2700
450
120
MAXIMO MX 15 Panel Formwork
34
Item no. Weight kg
101813 8.040 Filler Profile TPP 270, AluFor compensation with 21 mm filler plates.
2700
51
98
60
114165114186114174114128
14.700 15.700 16.800 10.000
Wall Thickness Compensations WDA MX 270Wall Thickness Comp. WDA MX 270 x 4Wall Thickness Comp. WDA MX 270 x 5Wall Thickness Comp. WDA MX 270 x 6Wall Thickness Comp. WDA MX 270 x 10, AluFor adjusting to wall thicknesses.
B 40 50 60 100
2700
B 60
120
100 62
120
111872 41.800 Articulated Corner MXGA 2700.810 m². Made of aluminium, for oblique angles from 75° upwards, external.
2700
120
150 150
MAXIMO MX 15 Panel Formwork
35
Item no. Weight kg
023060105953
17.200 19.000
Stopend Panels TRIO ATStopend Panel TRIO AT 270 x 3Stopend Panel TRIO AT 270 x 5External piece for stopend formwork.
NoteConcrete cover approx. 30 or 50 mm.
2700
AT 270 x 3 AT 270 x 5210
120
210
120
023074023075023077023076
29.200 33.400 38.600 42.500
Stopend Panels TRIO MTF with waterstopStopend Panel TRIO MTF 270 x 20Stopend Panel TRIO MTF 270 x 24/25Stopend Panel TRIO MTF 270 x 30Stopend Panel TRIO MTF 270 x 35/36Centre piece with waterstop bar installation for stopend formwork.
B 118 158 218 268
2700
120
B
023061023062023064023065
27.500 30.400 37.300 41.300
Stopend Panels TRIO MT without waterstopStopend Panel TRIO MT 270 x 20Stopend Panel TRIO MT 270 x 24/25Stopend Panel TRIO MT 270 x 30Stopend Panel TRIO MT 270 x 35/36Centre piece without waterstop bar installation for stopend formwork.
B 118 158 218 268
2700
120
B
MAXIMO MX 15 Panel Formwork
36
Item no. Weight kg
112221 51.200 Panel MX 120 x 600.720 m². Panel with 18 mm plywood.
600
600
1200
300 300
600
120
112152 67.700 Panel MX 120 x 901.080 m². Panel with 18 mm plywood.
900
1200
120450 450
600
600
112143 90.700 Panel MX 120 x 1201.440 m². Panel with 18 mm plywood.
600
600
600 6001200
1200
120
112104 165.000 Panel MX 120 x 2402.880 m². Panel with 18 mm plywood.
600
600
540 1320 5402400
1200
120
MAXIMO MX 15 Panel Formwork
37
Item no. Weight kg
115299 48.700 Inside Corner MXI 120 x 50/200.840 m². Panel with 18 mm plywood. For 90° internal corners.
Complete with4 pc. 124895 PVC Plug MXM 15 Ø 18.3
600
600
1200
200
500
120
112850 53.400 Multi Panel MXM 120 x 600.720 m². Panel with 18 mm plywood. For oblique angles, wall connections etc.
Complete with11 pc. 124895 PVC Plug MXM 15 Ø 18.3
600
600
1200 10040010 x 40 = 100
600
120
112239 27.400 Panel MX 120 x 300.360 m². Panel with 18 mm plywood.
600
600
150 150
1200
300120
112232 37.000 Panel MX 120 x 450.540 m². Panel with 18 mm plywood.
600
600
1200
225450
225 120
MAXIMO MX 15 Panel Formwork
38
Item no. Weight kg
112761 67.200 Outside Corner MXA 120 x 350.840 m². Panel with 18 mm plywood. For 90° external corners.
1200
120
350
112830 76.100 Outside Corner MXA 120 x 451.080 m². Panel with 18 mm plywood. For 90° external corners.
1200
450
120
117915 139.000 Shaft Corner MXSE 120Panel for forming 90° inside corners along with striking and moving complete internal shaft formwork units.
Technical DataPermissible load-bearing point capacity 2.0 t.
600
600
1200
120
480 60
0
112689 80.500 Inside Corner MXI 120 x 601.440 m². Panel with 18 mm plywood. For 90° internal corners.
600
600
1200
120
600
480
MAXIMO MX 15 Panel Formwork
39
Item no. Weight kg
101823 3.590 Filler Profile TPP 120, AluFor compensation with 21 mm filler plates.
1200
98
5160
114212114191114181114142
6.420 6.980 7.480 4.510
Wall Thickness Compensations MX 120Wall Thickness Comp. MX 120 x 4Wall Thickness Comp. MX 120 x 5Wall Thickness Comp. MX 120 x 6Wall Thickness Comp. MX 120 x 10, AluFor adjusting to wall thicknesses.
B 40 50 60 100
1200 B
120
100
120
111850 19.000 Articulated Corner MXGA 1200.360 m². Made of aluminium, for oblique angles from 75° upwards, external.
1200 150 150
120
113246 31.200 Articulated Corner MXGI 1200.720 m². Made of aluminium, for oblique angles from 75° upwards, internal.
1200 300 300
120
MAXIMO MX 15 Panel Formwork
40
Item no. Weight kg
112115 121.000 Panel MX 90 x 2402.160 m². Panel with 18 mm plywood.
450
450
900
540 1320 5402400
120
023081023080023078023079
12.800 14.700 16.800 18.600
Stopend Panels TRIO MTFStopend Panel TRIO MTF 120 x 20Stopend Panel TRIO MTF 120 x 24/25Stopend Panel TRIO MTF 120 x 30Stopend Panel TRIO MTF 120 x 35/36Centre piece with waterstop bar installation for stopend formwork.
B 118 158 218 268
1200 B
120
023068023069023071023072
11.800 13.500 16.300 18.500
Stopend Panels TRIO MTStopend Panel TRIO MT 120 x 20Stopend Panel TRIO MT 120 x 24/25Stopend Panel TRIO MT 120 x 30Stopend Panel TRIO MT 120 x 35/36Centre piece without waterstop bar installation for stopend formwork.
B 118 158 218 268
1200 B
120
023067105978
7.780 8.580
Stopend Panels TRIO ATStopend Panel TRIO AT 120 x 3Stopend Panel TRIO AT 120 x 5External piece for stopend formwork.
NoteConcrete cover approx. 30 mm.
1200 210
120
AT 120 x 3 AT 120 x 5210
120
MAXIMO MX 15 Panel Formwork
41
Item no. Weight kg
112271 21.900 Panel MX 90 x 300.270 m². Panel with 18 mm plywood.
450
450
150 150300
900
120
112265 31.200 Panel MX 90 x 450.405 m². Panel with 18 mm plywood.
900
450
120225225
450
450
112259 36.600 Panel MX 90 x 600.540 m². Panel with 18 mm plywood.
450
450
900
300 300
600
120
112252 48.900 Panel MX 90 x 900.810 m². Panel with 18 mm plywood.
450
450
450 450
900
900
120
MAXIMO MX 15 Panel Formwork
42
Item no. Weight kg
126917 52.400 Outside Corner MXA 90 x 350.630 m². Panel with 18 mm plywood. For 90° external corners.
900
120
350
350
126923 59.600 Outside Corner MXA 90 x 450.808 m². Panel with 18 mm plywood. For 90° external corners.
900
120450
449
112715 68.000 Inside Corner MXI 90 x 601.080 m². Panel with 18 mm plywood. For 90° internal corners.
450
450
900
120
600
480
115307 36.800 Inside Corner MXI 90 x 50/200.630 m². Panel with 18 mm plywood. For 90° internal corners.
Complete with4 pc. 124895 PVC Plug MXM 15 Ø 18.3
450
450
900
200
500
120
MAXIMO MX 15 Panel Formwork
43
Item no. Weight kg
115315 29.600 Inside Corner MXI 60 x 50/200.420 m². Panel with 18 mm plywood. For 90° internal corners.
Complete with4 pc. 124895 PVC Plug MXM 15 Ø 18.3
500
200
300
300
600
120
112292 16.200 Panel MX 60 x 300.180 m². Panel with 18 mm plywood.
300
300 60
0
150 150300
120
112286 21.900 Panel MX 60 x 450.270 m². Panel with 18 mm plywood.
300
300
225 225
450
600
120
112280 28.400 Panel MX 60 x 600.360 m². Panel with 18 mm plywood.
300
300 60
0
600
300 300 120
112126 88.000 Panel MX 60 x 2401.440 m². Panel with 18 mm plywood.
300
300 60
0
540 1320 5402400
120
MAXIMO MX 15 Panel Formwork
44
Item no. Weight kg
113847 4.030 MX 15 Tie 15 – 25For wall thicknesses 15 – 25 cm.
NoteSpray with release agent before every use to ensure easier striking.Technical DataPermissible tension force 90 kN.
130
196
688
112133 52.800 Panel MX 30 x 2400.720 m². Panel with 18 mm plywood.
150
150
300
540 1320 5402400
120
112778 37.400 Outside Corner MXA 60 x 350.420 m². Panel with 18 mm plywood. For 90° external corners.
600
350
120
112837 42.800 Outside Corner MXA 60 x 450.540 m². Panel with 18 mm plywood. For 90° external corners.
600 450
120
112726 45.400 Inside Corner MXI 60 x 600.720 m². Panel with 18 mm plywood. For 90° internal corners.
300
300 60
0
600
120
600
MAXIMO MX 15 Panel Formwork
45
Item no. Weight kg
116841 1.450 MX 15 Tie SpannerFor easy release of the MX Tie.
SW 19
434
112386 2.580 MX 15 WingnutCounter nut for Tie MX.
Technical DataPermissible tension force 90 kN.
136130
196
112464 4.430 MX 15 Tie 30 – 40For wall thicknesses 30 – 40 cm.
NoteSpray with release agent before every use to ensure easier striking.Technical DataPermissible tension force 90 kN.
838
196
130
112387 4.170 MX 15 Tie 20 – 30For wall thicknesses 20 – 30 cm.
NoteSpray with release agent before every use to ensure easier striking.Technical DataPermissible tension force 90 kN.
130
196
738
MAXIMO MX 15 Panel Formwork
46
Item no. Weight kg
124942 23.400 Waler MAR 170-3For longitudinal compensation, height extensions, stopend formwork and special applications with MAXIMO. With captive connecting components.
Technical DataPermissible bending moment 3.9 kNm.
1700
3030 11
5
264
126
124941 14.100 Waler MAR 85-3For longitudinal compensation, height extensions, stopend formwork and special applications with MAXIMO. With captive connecting components.
Technical DataPermissible bending moment 3.9 kNm.
850 115
3030 264
126
023500 4.580 Alignment Coupler BFD, galv.For all panel connections for MAXIMO, TRIO and RUNDFLEX. Fillers up to 10 cm.
Technical DataPermissible tension force 20.0 kN.
164
288 259
55 max 220
796061 0.450 Scaffold Builders Ratchet
300
SW 19
SW 22
MAXIMO MX 15 Panel Formwork
47
Item no. Weight kg
023640 1.140 Bulkhead Tie TS, galv.For force application from the stopend formwork in MAXIMO and TRIO panels. DW 15 thread.
Technical DataPermissible tension force 20.0 kN.
440
140
58
DW 15
023650 0.769 Hook Tie DW 15, l = 400 mm, galv.For connecting accessories to MAXIMO and TRIO panels. DW 15 thread.
Technical DataPermissible tension force 20.0 kN.
400
58
20
DW 15
023820 0.375 Hook Tie Head DW 15, galv.For connecting accessories to MAXIMO and TRIO panels. DW 15 thread.
Technical DataPermissible tension force 20.0 kN.
82 30
68Ø15
023551 8.520 Waler 85Corresponds to Compensation Waler TAR 85 but without mounting hooks.
Technical DataPermissible bending moment 4.4 kNm.
3030
105
850 80
127732 11.000 Stopend Waler MX 15 - 40
612max min 362
170
775
53
259
MAXIMO MX 15 Panel Formwork
48
Item no. Weight kg
112588 5.520 Stripping Bar TRIO
1180
Ø26
115350123842
6.330 9.090
Tension and Compression Braces MXTension and Compression Brace MX 15 – 40Tension and Compression Brace MX 15 – 100For use with foundation formwork up to 1.20 m high and as replacement for the top anchor of the MAXIMO 330.
Complete with1 pc. 115331 Bolt Ø 12 x 96, galv.1 pc. 018060 Cotter Pin 4/1, galv.NoteAdjustable in 0.5-cm-increments from 15 to 40 cm and in 0.5-cm-increments from 15 to 100 cm.Technical DataPermissible tension and compressive force 9 kN.
750 / 1350
174
65
Ø13,2
61
023660 3.300 Brace Connector TRIO, galv.For connecting push-pull props and kicker braces to MAXIMO and TRIO Panels. Mounted on vertical and horizontal struts.
Complete with1 pc. 027170 Pin Ø 16 x 42, galv.1 pc. 018060 Cotter Pin 4/1, galv.
169
222
185
115640 5.980 Bulkhead Tie MX DW 20For forming wall offsets with MAXIMO in connection with the Multi Panel MXM.
208
255 44130
MAXIMO MX 15 Panel Formwork
49
Item no. Weight kg
117322 25.000 Lifting Gear MXFor transporting stacks of MAXIMO and TRIO Panels.
NoteFollow Instructions for Use!
.
117321 31.000 Lifting Gear Combi MXFor transporting stacks of MAXIMO and TRIO Panels. For attaching Lifting Hook MAXIMO 1.5 t and Stacking Device MAXIMO.
NoteFollow Instructions for Use!
.
023630 2.080 Top Tie Bracket-2 AH, galv.For grid-independent anchoring outside of the panel, especially for foundations and height exten-sions.
Technical DataPermissible anchor tension force:Hole 1 = 30 kNHole 2 = 15 kN
100 145
Ø20,5
1501
2
101633 9.790 Adjusting Bracket MXFor erecting PERI Panel Formwork up to h = 4.50 m.
NoteFollow Instructions for Use!Height Adjustment ± 5 cm.
190
236 36
5
144
Ø25
SW 24
MAXIMO MX 15 Panel Formwork
50
Item no. Weight kg
023440 0.312 Lifting Pin TRIOFor easy carrying of TRIO Panels.
260Ø18
113019 0.068 Stacking Device MXFor easy stacking of MAXIMO panels.
110
50 90
115058 7.450 Stacking Device MAXIMOFor stacking and transportation of 2 – 5 MAXIMO or TRIO Panels of all sizes. Suitable for crane and fork-lift transport.
NoteFollow Instructions for Use!Technical DataPermissible load-bearing capacity 650 kg per post, 2.6 t per stack.
105
810
150
115168 7.470 Lifting Hook MAXIMO 1.5 tFor transporting MAXIMO and TRIO Panels.
NoteFollow Instructions for Use!Technical DataPermissible load-bearing capacity: Steel elements 1.5 t Alu elements 750 kg
60 110
218
110
332
58185
MAXIMO MX 15 Panel Formwork
51
Item no. Weight kg
022950 129.000 Concreting Platform TRIO 120 x 270Working and concreting platform for MAXIMO and TRIO. Attached from above to the panel, self-securing.
Technical DataPermissible load 150 kg/m2.
2680
1800440
996
1210
1165
123 1330
440
510
023670023680
12.600 16.700
Scaffold Brackets TRGScaffold Bracket TRG 80Scaffold Bracket TRG 120For assembly of a working and concreting scaffold with MAXIMO and TRIO. Mounted on horizontal and vertical struts.
Technical DataPermissible load 150 kg/m2 with maximum width of influence 1.35 m.
165
673
1051
930 / 1297798 / 1165
159
120
440
3565
MAXIMO MX 15 Panel Formwork
52
Item no. Weight kg
118105 0.699 Stacking Device R MXA
153
85 156
118103 0.700 Stacking Device L MXA
153
85 156
116292 4.730 Guardrail Post HSGP-2As guardrail for different systems.
35
120
1050
1300
450
65
101592 2.810 Guardrail Post Holder TRIOFor assembling of a guardrail to TRIO panels.
Complete with1 pc. 018060 Cotter Pin 4/1, galv.
100
302 43
213
155
116292 4.730AccessoriesGuardrail Post HSGP-2
MAXIMO MX 15 Panel Formwork
53
Item no. Weight kg
118100 0.652 Stacking Device MX Flat for Shaft Corner MXSE
176
149
17677
118112 0.613 Stacking Device R MXI
77 129
151
118110 0.614 Stacking Device L MXI
77 129
151
MAXIMO MX 15 Panel Formwork
54
Item no. Weight kg
113255 0.414 Bolt SB-MAXIMO, galv.For connecting MAXIMO panels with Brace Frame SB.
126179
Ø19
Ø45
114107 114417
1.190 1.400
AccessoriesSleeve SB-MAXIMO, galv.Sleeve SB-MAXIMO WDMX
025740 9.140 Connector SB-A, B, C - MX/TR/DFor connecting MAXIMO, TRIO and DOMINO panels with Brace Frames SB-A0, A, B, C.
Note1 piece per anchor point.
125
130
120
130
027690 113255 114107 114417
0.368 0.414 1.190 1.400
AccessoriesBolt SB-TRIO/DOMINO, galv.Bolt SB-MAXIMO, galv.Sleeve SB-MAXIMO, galv.Sleeve SB-MAXIMO WDMX
027680 49.600 Connector SB-1, 2 - MX/TR/DFor assembly of Brace Frame SB-1, 2 to MAXIMO, TRIO and DOMINO panels.
Technical DataPermissible load-bearing point capacity 1.0 t with crane sling angle ≤ 15°.
6017
70m
in12
70m
ax16
50
250
120
490
650
265
160
Ø21
240
027690 027590 113255 114107 114417
0.368 2.400 0.414 1.190 1.400
AccessoriesBolt SB-TRIO/DOMINO, galv.Hook Strap for SB-1, 2Bolt SB-MAXIMO, galv.Sleeve SB-MAXIMO, galv.Sleeve SB-MAXIMO WDMX
MAXIMO MX 15 Panel Formwork
55
Item no. Weight kg
126991126988
0.066 0.077
Stoppers MX 15Stopper MX 15 - 75 MF-SStopper MX 15 - 75 MF-LFor closing MX Tie Holes in the concrete.
NoteFor use with pressing water (waterproof concrete). Test report available!
30Ø
Ø17,
5/Ø1
9,5 74
114300 0.002 PVC Plug MX 15 Ø 17,5 – 22For closing MX tie holes in the concrete.
18
32Ø
124895 0.002 PVC Plug MXM 15 Ø 18.3For MAXIMO Multi Panel MXM, Internal Corners 50/20 and standard panels for single faced use.
24
23Ø
114417 1.400 Sleeve SB-MAXIMO WDMXFor connecting MAXIMO panels to Brace Frames SB.
NoteFor use with Sealing Sleeve MX 15 item-no. 123603 and Sealing Sleeve MX 18 item-no. 123604.
97 54Ø
113255 0.414AccessoriesBolt SB-MAXIMO, galv.
114107 1.190 Sleeve SB-MAXIMO, galv.For connecting MAXIMO panels with Brace Frame SB.
NoteFor use with Sealing Sleeve MX Ø 16item-no. 112342 and Nut Sealing Sleeve MX Ø 16 item-no. 112338.
82 54Ø
113255 114417
0.414 1.400
AccessoriesBolt SB-MAXIMO, galv.Sleeve SB-MAXIMO WDMX
MAXIMO MX 15 Panel Formwork
56
Item no. Weight kg
031643 0.241 DK Concrete Cone UNI 58/52For closing anchor points with DK Sealing Cone DW 15/55, DW 20/55, DW 26/55, SK Anchor Cone DW 15, Magnet Cone MX 15 - 55, Magnet Cone MX 18 - 55, Arch. Leading Cone M24.
NoteDelivery unit 50 pieces.
52
58,5
Ø
48Ø112937 0.174 Sealing Cone MX 15 – 55
For use with MAXIMO. Use with Anchor MX.NoteFor use with waterproofed concrete or architectu-ral concrete.
54
62Ø
126696 1.220AccessoriesMagnet Cone Spanner MX 15 / MX 18
126999 0.037 Stud Spanner MX 15-2Packaging units contain Stoppers MX 15.
132
36 27
127065 0.046 Stopper MX 15 – 50 OF-LSFor closing MX Tie Holes in the concrete if the flange should not be visible.
NoteFor use with non-pressing water.
50
18Ø
127064 0.050 Stopper MX 15 – 50 MF-LSFor closing MX Tie Holes in the concrete.
NoteFor use with non-pressing water.
18Ø 30Ø
51
MAXIMO MX 15 Panel Formwork
57
Item no. Weight kg
031636 0.063 DK Cone DW 15/55For waterproof, fire-resistant and soundproof anchor points with Tie Rod DW 15. Used with Spacer Tube rough 22.
NoteDelivery unit 50 pieces.
22,3
Ø
61,5
Ø
23 54
125299 0.013 Cone MX DR 22/2For the use of DW 15 Tie Rods. Fitts for Spacer Tubes DR 22.
63Ø
21Ø
15
114592 0.021 Spacer MX 15 – 10 mm
32Ø 10
26Ø
126696 1.220 Magnet Cone Spanner MX 15 / MX 18For dismantling of Magnet Cone MX 15 and MX 18.
591
164
30
MAXIMO MX 15 Panel Formwork
58
Item no. Weight kg
117466 10.600 Push-Pull Prop RS 210, galv.Extension length l = 1.30 – 2.10 m. For aligning PERI formwork systems and precast concrete elements.
NotePermissible load see PERI Design Tables.
1300min max 2100
Ø211178
60,6
Ø
9
Ø17
Ø48,3
125337 1.390 Extraction Tool MX SealingFor remove of the Sealing MX 15 and MX 18.
178
55Ø 110
123603 0.016 Sealing MX 15
39Ø
17Ø
10
031637 0.055 DK Cone DW 20/55For waterproof, fire-resistant and soundproof anchor points with Tie Rod DW 20. Use with Spacer Tube rough 28.
NoteDelivery unit 50 pieces.
22 55
61,5
Ø
28,5
Ø
MAXIMO MX 15 Panel Formwork
59
Item no. Weight kg
117469 40.000 Push-Pull Prop RS 650, galv.Extension length l = 4.30 – 6.50 m. For aligning PERI formwork systems and precast concrete elements.
NotePermissible load see PERI Design Tables.
4300min max 6500
88,9
Ø4140
Ø21
Ø48,3
Ø17
117468 23.000 Push-Pull Prop RS 450, galv.Extension length l = 2.80 – 4.50 m. For aligning PERI formwork systems and precast concrete elements.
NotePermissible load see PERI Design Tables.
min 2800 max 4500
2670
73ØØ21
Ø48,3
Ø17
9
117467 15.500 Push-Pull Prop RS 300, galv.Extension length l = 1.90 – 3.00 m. For aligning PERI formwork systems and precast concrete elements.
NotePermissible load see PERI Design Tables.
min 1900 max 3000
1773
64,5
Ø
Ø21
Ø48,3
9
Ø17
118238 12.200 Push-Pull Prop RS 260, galv.Extension length l = 2.30 – 2.60 m. For aligning PERI formwork systems and precast concrete elements.
NotePermissible load see PERI Design Tables.
min 2300 max 2600
60,6
Ø2178Ø21
9
Ø17
Ø48,3
MAXIMO MX 15 Panel Formwork
60
Item no. Weight kg
117343 3.250 Base Plate-2 for RS 210 – 1400, galv.For assembly of Push-Pull Props RS 210, 260, 300, 450, 650, 1000 and 1400.
Complete with2 pc. 105400 Pin Ø 20 x 140, galv.2 pc. 018060 Cotter Pin 4/1, galv.
261
106
5264
Ø21
124777 0.210AccessoriesAnchor Bolt PERI 14/20 x 130
103800 271.000 Push-Pull Prop RS 1400, galv.Extension length l = 6.40 – 14.00 m. For aligning PERI formwork systems.
NotePermissible load see PERI Design Tables. Chain can be operated from bottom.
6400min max 14000
6290
400020 x 200 = 400020 x 200 =
Ø48,3
Ø21 Ø21Ø17
Ø48,3
10
028990 115.000 Push-Pull Prop RS 1000, galv.Extension length l = 6.40 – 10.00 m. For aligning PERI formwork systems.
NotePermissible load see PERI Design Tables.
min 6325 max 10000
10
102
Ø
Ø21
Ø48,3
Ø21
Ø17
MAXIMO MX 15 Panel Formwork
61
Item no. Weight kg
028020 22.000 Push-Pull Prop RSS IIExtension length l = 2.91 – 3.80 m. For aligning PERI formwork systems.
NotePermissible load see PERI Design Tables.
min 2910 max 3800
Ø16,5Ø16,52775
Ø32
10
70Ø
15
113397 1.600 Spindle Handle RSS / AVSpindle Handle for screwing on Push-Pull-Props RSS I, RSS II, RSS III and Kickers AV 210 and AV 190 complete with 2 bolts and nuts M8.
196
179
130
028010 17.900 Push-Pull Prop RSS IExtension length l = 2.05 – 2.94 m. For aligning PERI formwork systems.
NotePermissible load see PERI Design Tables.
2050min max 2940
1915Ø16,5
10
Ø32
70Ø
126666 3.070 Base Plate-3 for RS 210-1400For assembly of Push-Pull Props RS 210, 260, 300, 450, 650, 1000 and 1400.
Complete with2 pc. 105400 Pin Ø 20 x 140, galv.2 pc. 018060 Cotter Pin 4/1, galv.1 pc. 113063 Bolt ISO 4014 M12 x 80-8.8, galv.
264
64
52
105
Ø21
MAXIMO MX 15 Panel Formwork
62
Item no. Weight kg
057087057088
3.720 4.410
Kickers AVKicker AV 82Kicker AV 111For aligning PERI formwork systems.
min. L max. L 500 820 790 1110 Complete with1 pc. 027170 Pin Ø 16 x 42, galv.1 pc. 018060 Cotter Pin 4/1, galv.NotePermissible load see PERI Design Tables.
min 790 max 1110min 500 max 820
38Ø
390
10 10
Ø16,5
Ø30
Ø16x42
690
106000 1.820 Base Plate-2 for RSS, galv.For assembly of RSS Push-Pull Props.
Complete with1 pc. 027170 Pin Ø 16 x 42, galv.1 pc. 018060 Cotter Pin 4/1, galv.
150
Ø21
Ø11
100 1285
124777 0.210AccessoriesAnchor Bolt PERI 14/20 x 130
028030 38.400 Push-Pull Prop RSS IIIExtension length l = 4.60 – 6.00 m. For aligning PERI formwork systems.
NotePermissible load see PERI Design Tables.
min 4600 max 6000
4399Ø16,5 Ø16,5
Ø48,3
915
82,5
Ø
MAXIMO MX 15 Panel Formwork
63
Item no. Weight kg
028120 17.000 Kicker AV RSS IIIExtension length l = 2.03 – 2.92 m. For aligning PERI formwork systems.
Complete with1 pc. 027170 Pin Ø 16 x 42, galv.1 pc. 018060 Cotter Pin 4/1, galv.NotePermissible load see PERI Design Tables.
min 2030 max 2920
1915Ø16x42 Ø16,5
Ø32
10 10
70Ø
108135 12.900 Kicker AV 210Extension length l = 1.28 – 2.10 m. For aligning PERI formwork systems.
Complete with1 pc. 027170 Pin Ø 16 x 42, galv.1 pc. 018060 Cotter Pin 4/1, galv.NotePermissible load see PERI Design Tables.
min 1280 max 2100
Ø16x42 Ø16,5
Ø36
70Ø
1171
1010
028110 5.180 Kicker AV 140Extension length l = 1.08 – 1.40 m. For aligning PERI formwork systems.
Complete with1 pc. 027170 Pin Ø 16 x 42, galv.1 pc. 018060 Cotter Pin 4/1, galv.NotePermissible load see PERI Design Tables.
min 1080 max 1400
38Ø Ø16x42Ø16,5
Ø30
980
10 10
MAXIMO MX 15 Panel Formwork
64
Item no. Weight kg124777 0.210 Anchor Bolt PERI 14/20 x 130
For temporary fixation to reinforced concrete structures.
NoteSee PERI data sheet! Drilling Ø 14 mm.
130
SW 24Ø14
65
66
67
2
1
3
4
5
6
9
11
12
1316
17
18
19
20
22
21
24
2829
30
32
33
34
38
41
42
46
48
52
44
53
60
68
02 PERI S.A.S. 77109 Meaux Cedex [email protected] www.peri.fr
03 PERI AG 8472 Ohringen [email protected] www.peri.ch
04 PERI S.A.U. 28110 Algete - Madrid [email protected] www.peri.es
05 N.V. PERI S.A. 1840 Londerzeel [email protected] www.peri.be
06 PERI Holding B.V. 5480 AH-Schijndel [email protected] www.peri.nl
07 PERI Formwork Systems, Inc. Elkridge, MD 21075 [email protected] www.peri-usa.com
08 PT Beton Perkasa Wijaksana Jakarta 10210 [email protected] www.peri.com
09 PERI S.p.A. 20060 Basiano [email protected] www.peri.it
10 PERI Japan K.K. Tokyo 103-0015 [email protected] www.perijapan.jp
11 PERI Ltd. Rugby, CV23 0AN [email protected] www.peri.ltd.uk
12 PERI Kalip ve Iskeleleri Sanayi ve Ticaret Ltd. Esenyurt / İstanbul 34510 [email protected] www.peri.com.tr
13 PERI Kft. 1181 Budapest [email protected] www.peri.hu
14 PERI Formwork Malaysia Sdn. Bhd. 43300 Seri Kembangan, Selangor Darul Ehsan [email protected] www.perimalaysia.com
15 PERI Asia Pte Ltd Singapore 387355 [email protected] www.periasia.com
16 PERI Ges.mbH 3134 Nußdorf ob der Traisen [email protected] www.peri.at
17 PERI spol. S r.o. 252 42 Jesenice u Prahy [email protected] www.peri.cz
18 PERI Danmark A/S 2670 Greve [email protected] www.peri.dk
19 PERI Suomi Ltd. Oy 05460 Hyvinkää [email protected] www.perisuomi.fi
20 PERI Norge AS 3036 Drammen [email protected] www.peri.no
21 PERI Polska Sp. z o.o. 05-860 Płochocin [email protected] www.peri.com.pl
22 PERIform Sverige AB 30262 Halmstad [email protected] www.periform.se
23 PERI (Korea) Ltd. Seoul 06243 [email protected] www.perikorea.com
24 Pericofragens Lda. 2790-326 Queijas [email protected] www.peri.pt
25 PERI S.A. B1625GPA Escobar – Bs. As. [email protected] www.peri.com.ar
26 PERI Formas e Escoramentos Ltda. Vargem Grande Paulista – SP [email protected] www.peribrasil.com.br
27 PERI Chile Ltda. Colina, Santiago de Chile [email protected] www.peri.cl
28 PERI România SRL 077015 Baloteşti [email protected] www.peri.ro
29 PERI Agency 2000 Maribor [email protected] www.peri.com
30 PERI spol. s. r.o. 903 01 Senec [email protected] www.peri.sk
31 PERI Australia Pty. Ltd. Glendenning NSW 2761 [email protected] www.periaus.com.au
32 PERI AS 76406 Saku vald Harjumaa [email protected] www.peri.ee
33 PERI Hellas Solely Owned Ltd. 194 00 Koropi [email protected] www.perihellas.gr
34 PERI SIA 2118 Salaspils novads, Rigas rajons [email protected] www.peri-latvija.lv
35 PERI (L.L.C.) Dubai U.A.E. [email protected] www.perime.com
36 PERI Formwork Systems, Inc. Bolton, ON – L7E 1K1 [email protected] www.peri.ca
01 Germany PERI GmbH Rudolf-Diesel-Strasse 19 89264 Weissenhorn [email protected] www.peri.com
France
Switzerland
Spain
Belgium/Luxembourg
Netherlands
USA
Indonesia
Italy
Japan
United Kingdom/Ireland
Turkey
Hungary
Malaysia
Singapore
Austria
Czech Republic
Denmark
Finland
Norway
Poland
Sweden
Korea
Portugal
Argentina
Brazil
Chile
Romania
Slovania
Slovakia
Australia
Estonia
Greece
Latvia
United Arab Emirates
Canada
PERI International
8
10
1415
23
67
68
31
35
3739 40
43
44
45
47
50 51
5854
70
69
57
5659 55
64
63
65
7
25
26
66
27
36
49
61
62
69
37 PERI Lebanon Sarl 90416 – Jdeideh [email protected]
38 PERI UAB 02300 Vilnius [email protected] www.peri.lt
39 PERI S.A.U. Tanger [email protected] www.peri.ma
40 PERI Formwork Engineering Ltd. Rosh Ha‘ayin, 48104 [email protected] www.peri.co.il
41 PERI Bulgaria EOOD 1839 Sofia [email protected] www.peri.bg
42 Armar ehf. 220 Hafnarfjörður [email protected] www.armar.is
43 TOO PERI Kazakhstan 050000 Almaty [email protected] www.peri.kz
44 OOO PERI 142407, Noginsk District [email protected] www.peri.ru
45 PERI (Pty) Ltd 7600 Stellenbosch [email protected] www.peri.co.za
46 TOW PERI 07400 Brovary [email protected] www.peri.ua
47 Egypt Branch Office 11341 Nasr City /Cairo [email protected] www.peri.com.eg
48 PERI – Oplate d.o.o. 22310 Šimanovci [email protected] www.peri.rs
49 PERI Cimbras y Andamios, S.A. de C.V. Estado de México, Huehuetoca [email protected] www.peri.com.mx
50 PERI Repesentative Office Baku [email protected] www.peri.com.tr
51 PERI Kalıp ve İskeleleri Aşgabat [email protected] www.peri.com.tr
52 IOOO PERI Belarus 220100 Minsk [email protected] www.peri.by
53 PERI oplate i skele d.o.o. 10 250 Luöko-Zagreb [email protected] www.peri.com.hr
54 PERI (India) Pvt Ltd Mumbai – 400064 [email protected] www.peri.in
55 PERI GmbH - Jordan 11947 Amman [email protected] www.peri.com
56 PERI Kuwait W.L.L. 13011 Kuwait [email protected] www.peri.com.kw
57 PERI Saudi Arabia Ltd. 21463 Jeddah [email protected] www.peri.com.sa
58 PERI Qatar LLC P.O.Box: 31295 - Doha [email protected] www.peri.qa
59 Sarl PERI Kouba 16092, Alger [email protected] www.peri.com
60 PERI Representative Office Tirane [email protected] www.peri.com.tr
61 PERI Peruana S.A.C. Villa El Salvador, Lima [email protected] www.peri.com.pe
62 PERI Panama Inc. 0832-00155 Panama City [email protected] www.peri.com.pa
63 Pericofragens, Lda. Luanda [email protected] www.peri.pt
64 PERI Nigeria Ltd. Lagos [email protected] www.peri.ng 65 PERI (L.L.C.) Muscat [email protected] www.perime.com
66 PERI S.A.S. Colombia Briceño, Cundinamarca [email protected] www.peri.com.co
67 PERI-Asia Philippines, INC. Makati City [email protected] www.peri.com.ph
68 PERI (Hong Kong) Limited Hong Kong SAR, PRC [email protected] www.perihk.com
69 PERI (Pty.) Ltd. Windhoek [email protected] www.peri.na
70 PERI (Pty.) Ltd. Matola [email protected] www.peri.co.mz
Lebanon
Lithuania
Morocco
Israel
Bulgaria
Iceland
Kazakhstan
Russian Federation
South Africa
Ukraine
Egypt
Serbia
Mexico
Azerbaijan
Turkmenistan
Belorussia
Croatia
India
Jordan
Kuwait
Saudi Arabia
Qatar
Algeria
Albania
Peru
Panama
Angola
Nigeria
Oman
Colombia
Philippines
Hong Kong
Namibia
Mozambique
The optimal System for every Project and every Requirement
PERI GmbHFormwork Scaffolding EngineeringRudolf-Diesel-Strasse 1989264 WeissenhornGermanyTel. +49 (0)7309.950-0Fax +49 (0)[email protected]
System-Independent Accessories
Wall Formwork Column Formwork
Slab Formwork Climbing Systems Tunnel Formwork Bridge Formwork
Shoring Systems Facade ScaffoldConstruction Scaffold Industrial Scaffold
Access Protection Scaffold Services
DE
en 1
2 | 2
015
5eb
792
140
© P
ER
I Gm
bH