Download - M Tech Regulations and Syllabus
![Page 1: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/1.jpg)
~
~/~ tf(M ( pr/¥fl-IP!~- ,,~.- ,(
(~
JAWAHARLAL NEHRUTECHNOLOGICAL UNIVERSITY: KAKINADA .
ACADEMIC REGULATIONS 3.009 ~OR_~:!ech (Regular) DEGREE CQURSE
(Effective for the students admitted into 'fIrstyear trom the academic year 2009-2010)
The M.Tech Degree of Jawaharlal Nehru Technological University ~akinada shall beconferred on candidates who are admitted to the program and fulfill all the requirementsfor the award of the Degree.
1.0 ELIGIBILITY FOR ADMISSIONS:"'1;"'"-. .rdiiIa.
Admission to the above program shall be made subject to the eligibility,qualifIcations and specialization prescribed by the University from time to time.
Admissions shall be made on the basis of merit rank obtained by the qualifying
candidate at ':inEntrance Test conducted by the University or on the basis of anyother order of merit approved by the University, subject to reservations prescribedby the university from time to time.AWARD OF M. TECH. DEGREE:2.0
2.1 A student shall be declared eligible for the award of the M.Tech degree, if he/shepursues a course of study and completes it successfully for not less than twoacademic years and not more than four academic years.A student, who fails to fulfIll all the academic requirements for the award of the
degree within four academic years from the year of his/her admission, shall forfeithis/her seat in M.Tech course.
The minimum instruction for each semester 95 clear instruction days.
2.2
r'--'
2.3
3.0 ATT~ N1!.3.1 A candl .. shall be deemed to have eligibility to write End Semester examinations
ifhe/she h s put in a minimum of 75% of attendance in aggregate of all thesubjects.
3.2 Condonation of shortage of attendance up to 10% i.e. 65% and above, and below75% may be given by the College academic committee.
:3.3 C~mdonationof shortage of attendance shall be granted only on genuine and validreasons on representations by the candidate with supporting evidence.
3.4 Shortage of attendance below 65 % shall in NO case be condoned.. 3.5 A candidate shall not be promote4 to the next semester unless he/she fulfills the
attendance requirements of the previous semester.3.6 A stipulated fee shall be payable towards condonation of shortage of attendance
![Page 2: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/2.jpg)
4.0 COURSES OF STUDY:
The following specializations are offered at present for the M.Tech course of study.
1234567891011121314151617181920212223242526272829
/'C
IA
and any other course as approved by the authorities of the University from time to time.
![Page 3: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/3.jpg)
5.0
5.1
"""
"
EVALUATION:
The performahce of the candidate in each semester shall be evaluated subject-wise,with a maximum of 100 marks for theory and 100 marks for Laboratory, on thebasis of Internal Evaluation and End Semester Examination.
For the theory subjects 60 marks shall be awarded based on the performance in theEnd Semester Examination, 40 marks shall be awarded based on the InternalEvaluation. The internal evaluation shall be made based on the average of themarks secured in the two Mid Term-Examinations conducted, one in the middle ofthe Semester and the other immediately after the completion of instruction. Eachmidterm examination shall be conducted for duration of 120 J11inuteswith 4questions to be .answered out of 4 questions.
5.2 For practical subjects. 60 marks shall be awarded based on the perfonTIancein theEnd Semester Examinations, 40 marks shall be awarded based on the day-to-dayperformance in Laboratory as Internal Marks.
5.3 There shall be a seminar presentation during 3rdsemester. For seminar, a studentunder the supervision of a faculty member, shall collect the literature on a topic andcritically review the literature and submit it to the Department in a report form andshall make an oral presentation before the Departmental Committee. TheDepartmental Committee consists of Head of the Department, supervisor and two
. other senior faculty members of the department.For Seminar there will be onlyinternal evaluation of 50 marks. A candidate has to secure a minimum of 50% to bedeclared successful.
5.4 A candidate shall be deemed to have secured the minimum academic requirementin a subject if he secures a minimum of 40% of marks in the End Examination anda minimum aggregate of 50% of the total marks in the End Semester Examinationand Internal Evaluation taken together. If a candidate secures a minimum of 40% ofmarks in the End Examination and 40% -49% of the total marks in the EndSemester Examination and Internal Evaluation taken together and secures an.overall aggregate of 50% in the total semester he may be passed in those subjectsalso.
5.5 In case the candidate does not secure the minimum academic requirement in anysubject (as specIfied in 5.4) he has to reappear for the End Examination in thatsubject. A candidate shall be given one chance to re-register for each subjectprovided the internal marks secured by a candidate are less than 50% and he hasfailed in the end examination. In such case candidate must re-register for thesubj~ct(s) and 'secure required minimum attendance. The attendance in the re-registered subject(s) shall be calculated separately to decide upon the eligibility forwriting the end examination in those subject(s). In the event of taking anotherchance, the internal marks and end examination marks obtained in the previousattempt are nullified. At a given time a candidate is permitted to re-register for amaximum of two subjects in addition to the subjects of regular semester subjects.
![Page 4: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/4.jpg)
5.6 The viva-voce examination shall be conducted at the end of the course work and atthe end of 4th semester or later depending on the completion of the Project.
5.7 Laboratory examination for M.Tech courses must be conducted with twoExaminers, one of them being Laboratory Class Teacher and seconq examiner shallbe appointed by the University.
6.0 EVALVATION OF PROJECT / DISSERTATION WORK:
Every candidate shall be required to submit thesis or dissertation after taking up atopic approved by the Project Review Committee.
6.1 A Project Review Committee (PRC) shall be constituted with Principal as chairperson, Head of the Department and two other senior faculty members of theconcerned department ( one will be the guide) .
6.2 Registration of Project Work: A candidate is permitted to register for the projectwork after satisfying the attendance requirement of all the subjects (theory andpractical subjects).
~
6.3 After satisfying 6.2, a candidate has to submit, in consultation with his projectsupervisor, the title, objective and plan of action of his project work ( Based on a'publication in a peer Reviewed Journal)to the Project Review Committee for itsapproval before the second semester end examinations. After obtaining the approvalof the Committee the student can initiate the Project work after the second semesterend examinations.
6.4 Every candidate shall wor rlt11s approved by the PRC of the College.
6.5 If a candidate wishes to change his supervisor or topic of the project he can do sowith approval of the PRC. However, the Project Review Committee (PRC) shallexamine whether the change of topic/supervisor leads to a major change of his initialplans of project proposal. If so, his date of registration for the project work startsfrom the date of change of Supervisor or topic as the case may be.
~...
6.6 A 'candidate shall submit status report in two stages at least with a gap of 3months between them.
6.7 The work on the project shall be initiated in the beginning of the second year andthe duration of the project is for two semesters. A candidate shall be allowed tosubmit the project report only after fulfilling the attendance requirements of all thesemesters with the approval of PRC and not earlier than 40 weeks from the date ofregistration of the project work. For the approval of PRC the candidate shall submitthe draft copy of thesis to the Principal (through Head of the Department) and shallmake an oral presentation before t~e PRC.
![Page 5: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/5.jpg)
6.8
6.9
6.10
6.11
f""
7.0
,......
The Candidate may be permitted to submit the Project Report If only the work isPublished/Accepted to be Published in a Journal/International conference ofrepute and relevance.
Three copies of the Project Thesis certified by the supervisor shall be submitted tothe College / School/Institute.
The thesis shall be adjudicated by one examiner selected by the University. Forthis, Principal of the College shall submit a panel of.5 examiners, who are eminentin that field with the help of the concerned guide and head of the department.
The viva-voce examination shall be conducted by a board consisting of thesupervisor, Head of the Department and the examiner who adjudicated the Thesis.
The Board shall jointly report candidates work as:
A. Excellent~. Good
C.SatisfactoryD.Unsatisfactory
Head of the Department shall coordinate and make arrangements for the conduct of" l-voce examination. If the report of the viva-voce is unsatisfactory, thecandidate will retake the viva-voce examination after three months. If he fails to
get a satisfactory report at the second viva-voce examination, the candidate maybe asked to submit a new project proposal to PRC starting with 6.5
~
AWARD OF DEGREE AND CLASS:
After a student has satisfied the requirements prescribed for the completion of theprogram and is eligible for the award of M. Tech. Degree he shall be placed in oneof the following three classes:
IH
(The marks in internal evaluation and end examination shall be shown separately in themarks memorandum)
Class Awarded % of marks to be securedFirst Class with Distinction 70% and above( Without any
Supplementary Appearance)First Class Below 70% but not less than 60%
70% and above (WithSupplementary Appearance)
Second Class Below 60% but not less than 50%
![Page 6: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/6.jpg)
8.0
9.0
10.0
10.1
10.2
10.3
lOA
--
WITHHOLDING OF RESULTS:
If the candidate has not paid any dues to the university or if any case of in-discipline is pending against him, the result of the candidate will be withheld and hewill not be allowed into the next higher semester. The issue of the degree is liableto be withheld in such cases.
TRASITORY REGULATIONS:
Candidate who have discontinued or have been detained for want of attendance orwho have failed after having undergone the course are eligible for admission to thesame or equivalent subjects as and when subjects are offered, subject to 5.5 and 2.0
GENERAL:
The academic regulations should be read as a whole for purpose of anyinterpretation.
-I
In case of any doubt or ambiguity in the interpretation of the above rules, thedecision of the Vice-Chancellor is final.
The University may change or amend the academic regulations and syllabus atany time and the changes and amendments made shall be applicable to all thestudents with effect from the date notified by the University.
Wherever the word he, him or his occur, it will also include she, her and hers.
***
~
![Page 7: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/7.jpg)
APPROVED SYLLABUS OF
M. TECH. COURSE
POWER AND INDUSTRIAL DRIVES
(From Academic Year 2009-2010)
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY
KAKINADA-533 003
![Page 8: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/8.jpg)
COURSE STRUCTURE
Name of the subjectHrs/Week
CreditsEvaluation (marks)
Lecture Tutorial PracticalInternal External
TotalTheory Practical
I Semester
1.Electrical Machine Modeling and Analysis
4 - - 8 40 60 -100
2. Analysis of Power Electronic Converters
4 - - 8 40 60 - 100
3. Power Electronic Control of DC Drives
4 - - 8 40 60 - 100
4. Microcontrollers & Applications
4 - - 8 40 60 - 100
5. Elective-I 4 - - 8 40 60 - 100
6. Elective-II 4 - - 8 40 60 - 100
7. Power Electronic Systems Simulation Lab
- - 3 4 40 - 60 100
Elective-I
i. Modern Control Theory
ii. Power Semiconductor Devices & Protection
Elective-II
i. Special Machines and controls
ii. Renewable Energy sources
![Page 9: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/9.jpg)
COURSE STRUCTURE
Name of the subject Hrs/Week Credits Evaluation (marks)
Lecture Tutorial Practical Internal External Total
Theory Practical
II Semester
1.Switched Mode Power Conversion
4 - - 8 40 60 - 100
2.Power Electronics
Control of AC Drives 4 - - 8 40 60 - 100
3.Flexible AC
Transmission Systems 4 - - 8 40 60 - 100
4.Digital Signal
Processing and
Applications4 - - 8 40 60 - 100
5. Elective-III 4 - - 8 40 60 - 100
6.Elective-IV 4 - - 8 40 60 - 100
7.Power Electronics and Drives Lab
- - 3 4 40 - 60 100
Elective-III
i. Digital Control Systems
ii. Intelligent Control
Elective-IV
i. Power Quality Management
ii. Energy Auditing, Conservation and Management
![Page 10: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/10.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
ELECTRICAL MACHINE MODELING AND ANALYSIS
Unit I: Basic concepts of Modeling Basic Two-pole Machine representation of Commutator machines, 3-phase synchronous machine with and without damper bars and 3-phase induction machine, Kron’s primitive Machine-voltage, current and Torque equations.
Unit II: DC Machine ModelingMathematical model of separately excited D.C motor – Steady State analysis-Transient State analysis-Sudden application of Inertia Load-Transfer function of Separately excited D.C Motor-Mathematical model of D.C Series motor, Shunt motor-Linearization Techniques for small perturbationsUnit III: Reference frame theoryReal time model of a two phase induction machine- Transformation to obtain constant matrices-three phase to two phase transformation-Power equivalence-
Unit IV: Dynamic modeling of three phase Induction MachineGeneralized model in arbitrary reference frame-Electromagnetic torque-Derivation of commonly used Induction machine models- Stator reference frame model-Rotor reference frame model-Synchronously rotating reference frame model-Equations in flux linkages-per unit model-Dynamic SimulationUnit V: Small Signal Modeling of Three Phase Induction Machine Small signal equations of Induction machine-derivation-DQ flux linkage model derivation-control principle of Induction machine.
Unit VI: Symmetrical and Unsymmetrical 2 phase Induction Machine Analysis of symmetrical 2 phase induction machine-voltage and torque equations for unsymmetrical 2 phase induction machine-voltage and torque equations in stationary reference frame variables for unsymmetrical 2 phase induction machine-analysis of steady state operation of unsymmetrical 2 phase induction machine- single phase induction motor - Cross field theory of single-phase induction machine.Unit VII: Modeling of Synchronous MachineSynchronous machine inductances –voltage equations in the rotor’s dq0 reference frame-electromagnetic torque-current in terms of flux linkages-simulation of three phase synchronous machine- modeling of PM Synchronous motor.
![Page 11: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/11.jpg)
Unit VIII: Dynamic Analysis of Synchronous MachineDynamic performance of synchronous machine, three-phase fault, comparison of actual and approximate transient torque characteristics, Equal area criteria.
Reference Books:1. Electric Motor Drives - Modeling, Analysis& control -R.Krishnan- Pearson Publications-1st edition -2002 (For chapter III, IV, V)2.Analysis of Electrical Machinery and Drive systems – P.C.Krause, Oleg Wasynczuk, Scott D.Sudhoff – Second Edition-IEEE Press ( for Chapters VI, VII,VIII)3. Generalized Theory of Electrical Machines – P.S.Bimbra-Khanna publications-5th edition-1995( For chapter I,II)4. Dynamic simulation of Electric machinery using Matlab / Simulink –Chee Mun Ong-Prentice Hall
![Page 12: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/12.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
ANALYSIS OF POWER ELECTRONICS CONVERTERS
Unit-I Single Phase AC voltage ControllersSingle Phase AC Voltage Controllers with RL and RLE loads-ac voltage controller’s with PWM control-Effects of source and load inductances –synchronous tap changers –Application- numerical problemsUnit-II Three Phase AC Voltage ControllersThree Phase AC Voltage controllers-Analysis of Controllers with star and delta connected resistive, resistive –inductive loads-Effects of source and load inductances–Application- numerical problems.Unit –III Single phase ac-dc convertersSingle phase Half controlled and Fully controlled Converters with RL load– Evaluation of input power factor and harmonic factor-Continuous and Discontinuous load current-Power factor improvements-Extinction angle control-symmetrical angle control-PWM single phase sinusoidal PWM-Single phase series converters- numerical problemsUnit-IV Three Phase ac-dc ConvertersThree Phase ac-dc Converters- Half controlled and fully controlled Converters with RL load– Evaluation of input power factor and harmonic factor-Continuous and Discontinuous load current-three phase dual converters-Power factor improvements-three phase PWM-twelve pulse converters- numerical problemsUnit-V Power Factor Correction ConvertersSingle-phase single stage boost power factor corrected rectifier, power circuit principle of operation, and steady state- analysis, three phase boost PFC converterUnit –VI Single phase PWM Inverters Principle of operation-Voltage control of single phase inverters - sinusoidal PWM – modified PWM –phase displacement Control – Trapezoidal, staircase, stepped, harmonic injection and delta modulation –numerical problems Unit VII: Three Phase PWM Inverters Voltage Control of Three-Phase Inverters- Sinusoidal PWM- 600 PWM- Third Harmonic PWM- Space
Vector Modulation- Comparison of PWM Techniques-current source inverters-Variable dc link inverter -numerical problemsUnit VIII: Multi level invertersIntroduction, Multilevel Concept, Types of Multilevel Inverters- Diode-Clamped Multilevel Inverter, Principle of Operation, Features of Diode-Clamped Inverter, Improved Diode-Clamped Inverter- Flying-Capacitors Multilevel Inverter- Principle of Operation, Features of Flying-Capacitors Inverter- Cascaded Multilevel Inverter- Principle of Operation- Features of Cascaded Inverter- Switching Device Currents-DC-Link Capacitor Voltage Balancing- Features of Multilevel Inverters- Comparisons of Multilevel ConvertersTextbooks1. Power Electronics-Md.H.Rashid –Pearson Education Third Edition- First Indian Reprint- 20082. Power Electronics- Ned Mohan, Tore M.Undelan and William P.Robbins –John Wiley & Sons -2nd Edition.
![Page 13: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/13.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
POWER ELECTRONIC CONTROL OF DC DRIVES
Unit-I Speed Torque characteristics of DC MotorsSeparately excited DC motors, Shunt motor, series motor and compound motor
Unit-II: Controlled Bridge Rectifier (1-Ф) with DC Motor LoadSeparately excited DC motors with rectified single phase supply- single phase semi converter and single phase full converter for continuous and discontinuous modes of operation – power and power factor.
Unit-III: Controlled Bridge Rectifier (3-Ф) with DC Motor LoadThree phase semi converter and three phase full converter for continuous and discontinuous modes of operation – power and power factor – Addition of Free wheeling diode – Three phase double converter.
Unit-IV: Three phase naturally commutated bridge circuit as a rectifier or as an inverterThree phase controlled bridge rectifier with passive load impedance, resistive load and ideal supply –Highly inductive load and ideal supply for load side and supply side quantities, shunt capacitor compensation, three phase controlled bridge rectifier inverter.
Unit-V: Closed loop control of phase controlled DC motor DrivesOpen loop Transfer function of DC Motor drive- Closed loop Transfer function of DC Motor drive –Phase-Locked loop control.
Unit-VI:Chopper controlled DC motor drivesPrinciple of operation of the chopper – Four quadrant chopper circuit – Chopper for inversion – Chopper with other power devices – model of the chopper –input to the chopper – Steady state analysis of chopper controlled DC motor drives – rating of the devices.
Unit- VII:Closed loop control of chopper fed DC motor DrivesSpeed controlled drive system – current control loop – pulse width modulated current controller –hysteresis current controller – modeling of current controller – design of current controller
Unit-VIII:Simulation of DC motor DrivesDynamic simulations of the speed controlled DC motor drives – Speed feedback speed controller –command current generator – current controller.
REFERENCES1. Power Electronics and Motor Control – Shepherd, Hulley, Liang – II Edition, Cambridge
University Press2. Power Electronic Circuits, Devices and Applications – M. H. Rashid – PHI.3. Electric Motor Drives Modeling, Analysis and Control – R. Krishnan, Prentice Hall India.4. Fundamentals of Electric Drives – G. K. Dubey – Narosa Publications – 1995.5. Power Semiconductor drives – G. K. Dubey.
![Page 14: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/14.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
MICROCONTROLLERS AND APPLICATIONS
Unit-I: 8051 MicrocontrollersIntroduction to Intel 8 bit & 16 bit Microcontrollers, MCS-51 Architecture, Registers in MCS-51, 8051 Pin Description, 8051 Connections, 8051 Parallel I/O Ports, Memory OrganizationUnit II: MCS-51 Addressing Modes and Instructions8051 Addressing Modes, MCS-51 Instruction Set, 8051 Instructions and Simple Programs, Using Stack Pointer, 8051 Assembly Language Programming, Development Systems and Tools, Software Simulators of 8051Unit-III: MCS-51 Interrupts, Timer/Counters and Serial CommunicationInterrupts, Interrupts in MCS-51, Timers and Counters, Serial Communication, Atmel Microcontrollers (89CXX and 89C20XX), Architectural Overview of Atmel 89C51 and Atmel 89C2051, Pin Description of 89C51 and 89C2051, Using Flash Memory Devices Atmel 89CXX and 89C20XXUnit-IV: Applications of MCS-51 and Atmel 89C51 and 89C2051 MicrocontrollersApplications of MCS-51 and Atmel 89C51 and 89C2051 Microcontrollers- Square Wave Generation-Rectangular Waves- Pulse Generation- Pulse Width Modulation- Staircase Ramp Generation- Sine Wave Generation- Pulse Width Measurement- Frequency CounterUnit- V. PIC MicrocontrollersPIC Microcontrollers: Overview and Features, PIC 16C6X/7X, FSR(File Selection Register) [Indirect Data Memory Address Pointer], PIC Reset Actions, PIC Oscillator Connections, PIC Memory Organizations, PIC PIC 16C6X/7X Instructions, Addressing Modes, I/O Ports, Interrupts in PIC 16C61/71, PIC 16C61/71 Timers, PIC 16C71 Analog-to-Digital Converter (ADC)Unit- VI. PIC 16F8XX Flash MicrocontrollersIntroduction, Pin Diagram of 16F8XX, STATUS Register, OPTION_REG Register, Power Control Register (PCON), PIC 16F8XX Program Memory, PIC 16F8XX Data Memory, DATA EEPROM and Flash Program EEPROM, Interrupts in 16F877, I/O Ports, Timers
Unit- VII: Interfacing and Microcontroller Applications- Light Emitting Diodes (LEDs), Push Buttons, Relays and Latch Connections, Keyboard Interfacing, Interfacing 7-Segment Displays, LCD Interfacing, ADC AND DAC Interfacing with 89C51 Microcontrollers
Unit- VIII: Industrial Applications of Microcontrollers - Measurement Applications, Automation and Control Applications
Reference books:1. Microcontrollers-Theory and Applications by Ajay V Deshmukh, McGraw Hills2. Microcontrollers by Kennith J ayala, Thomson publishers3 Microprocessor and Microcontrollers by Prof C.R.Sarma
![Page 15: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/15.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
MODERN CONTROL THEORY (Elective-I)
Unit –I Mathematical PreliminariesFields, Vectors and Vector Spaces – Linear combinations and Bases – Linear Transformations and Matrices – Scalar Product and Norms – Eigen values, Eigen Vectors and a Canonical form representation of Linear operators – The concept of state – State Equations for Dynamic systems – Time invariance and Linearity – Nonuniqueness of state model – State diagrams for Continuous – Time state models
Unit – II State Variable AnalysisLinear Continuous time model for physical systems – Existence and Uniqueness of Solutions to Continuous – Time State Equations – Solutions – Linear Time Invariant Continuous – Time State Equations – State transition matrix and it’s propertiesUnit – III Controllability and Observability General concept of Controllability - General concept of Observability Controllability tests for Continuous – Time Invariant systems - Observability tests for Continuous - Time Invariant systems -Controllability and Observability of state model in Jordan Canonical form - Controllability and Observability Canonical forms of State modelUnit – IV Non Linear Systems – 1 Introduction – Non Linear Systems – Types of Non – Linearities – Saturation – Dead – Zone – Backlash – Jump Phenomenon etc; - Singular Points – Introduction to Linearization of nonlinear systems, properties of Non Linear Systems – Describing function – describing function analysis of nonlinear systems- Stability analysis of Non – Linear systems through describing functions
Unit – V Non Linear Systems – 11Introduction to phase – plane analysis, Method of Isoclines for Constructing Trajectories, singular points, phase – plane analysis of nonlinear control systems.Unit - VI Stability AnalysisStability in the sense of Lyapunov, Lyapunov’s stability and Lyapunov’s instability theorems – Stability Analysis of the Linear Continuous time invariant systems by Lyapunov second method – Generation of Lyapunov functions – Variable gradient method – Krasooviski’s method.Unit – VII State Feedback Controllers And ObserversState Feedback Controller design through Pole Assignment – state observers: Full order and Reduced orderUnit – VIII Optimal ControlIntroduction to optimal control – Formulation of optimal control problems – calculus of variations –fundamental concepts, functional, variation of functional – fundamental theorem of theorem of Calculus of variations – boundary conditions – constrained minimization – formulation using Hamiltonian method – Linear quadratic regulator
Reference books:1. Modern Control System Theory by M. Gopal – New Age International – 19842. Modern Control Engineering by Ogata. K – Prentice Hall – 19973. Optimal control by Kirck
![Page 16: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/16.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
POWER SEMICONDUCTOR DEVICES & PROTECTION(Elective- I)
Unit I: Overview of Power Switching Devices: Introduction to power switching devices, classification of devices, controlled and un-controlled devices, i-v characteristics of ideal and real switching devices,
Unit-II: Power Diodes: Device structure and i-v characteristics, ratings & specifications, switching characteristics, reverse recovery, classification of various diodes: Schotky diode, line frequency diodes, fast recovery diodes,
Unit-III: Power Transistors: Device structure and i-v characteristics, ratings & specifications, switching characteristics, ON to OFF and OFF to ON state transitions, ON/OFF transition loss analysis, driver circuit.
Unit-IV: Power MOSFETs: Device structure and i-v characteristics, ratings & specifications, switching characteristics, ON to OFF and OFF to ON state transitions, ON/OFF transition loss analysis, driver circuit.
Unit-V: IGBT: Device structure and i-v characteristics, ratings & specifications, switching characteristics, ON to OFF and OFF to ON state transitions, ON/OFF transition loss analysis,. Comparison of all the above devices with reference to power handling capability, frequency of operation, driver circuit, .emerging power switching devices.
Unit-VI: Protection of the Switching Devices: Device protection against over voltage/currents, di/dt and dv/dt; safe operating area, design of snubbers for power devices.
Unit-VII: Thermal Management: Conduction and transition losses computation, thermal model of the device, steady-state temperature rise, electrical equivalent circuit of thermal model, sizing of the heat sink.
Unit-VIII: Passive Components: Magnetic circuit, review of design of line frequency inductors and transformers, design of high frequency inductors and transformers.
Text book1. Power Electronics Circuits- B. W. Williams
Reference books1. Power Electronics Circuits, Devices and Applications – M. H. Rashid-PHI-2. Power Electronics –Converters, Applications and Design – Mohan and Undeland-John Wiley & Sons3. Power Electronics: L. Umanand
![Page 17: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/17.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
SPECIAL MACHINES AND CONTROLS (Elective-II)
Unit I: Stepper MotorsConstructional features, Principle of operation, Modes of excitation torque production inVariable Reluctance (VR) stepping motor
Unit II: Characteristics of Stepper MotorsDynamic characteristics, Drive systems and circuit for open loop control, closed loop control of stepping motor.
Unit III: Switched Reluctance MotorsConstructional features, Principle of operation. Torque equation, Characteristics, ControlTechniques, Drive Concept.
Unit IV: Permanent Magnet Brushless DC MotorsCommutation in DC motors, Difference between mechanical and electronic commutators,Hall sensors, Optical sensors, Multiphase Brushless motor, Square wave permanentmagnet brushless motor drives, Torque and emf equation, Torque-speed characteristics,Controllers-Microprocessors based controller.
Unit V: Permanent Magnet Synchronous MotorsPrinciple of operation, EMF, power input and torque expressions, Phasor diagram, PowerControllers, Torque speed characteristics, Self control, Vector control, Current controlSchemes.
Unit VI: Servomotors Servomotor – Types – Constructional features – Principle of Operation – Characteristics -Control – Microprocessor based applications.
Unit VII: AC TachometersSchematic diagram, Operating principle, numerical problems
Unit VIII: Linear MotorsLinear Motors: Linear Induction Motor (LIM) Classification – Construction – Principle of operation – Concept of Current sheet –Goodness factor – DC Linear Motor (DCLM) types – Circuit equation –DCLM control-applications.
![Page 18: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/18.jpg)
References1. Miller, T.J.E. “Brushless Permanent Magnet and Reluctance Motor Drives”,Clarendon Press, Oxford, 1989.2. Kenjo, T, “Stepping Motors and their Microprocessor control”, Clarendon Press,Oxford, 1989.3. Naser A and Boldea I, “Linear Electric Motors: Theory, Design and PracticalApplication”, Prentice Hall Inc., New Jersey,19874. Floyd E Saner,”Servo Motor Applications”, Pittman USA, 1993.5. Kenjo, T and Naganori, S “Permanent Magnet and brushless DC motors”, ClarendonPress, Oxford, 1989.6. Generalized Theory of Electrical Machines – P.S.Bimbra-Khanna publications-5th edition-1995
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
RENEWABLE ENERGY RESOURCES (Elective-II)
Unit-ISolar Energy - Availability - Solar radiation data and measurement - Estimation of average solar radiation - Solar water heater types - Heat balance – Flat plate collector efficiency – Efficiency of heat removal -Thermo siphon flow calculation - Forced circulation calculation - Evacuated collectors - Basics of solar concentrators
Unit-IISolar Energy Applications - Solar air heaters – Solar Chimney - Crop driers - Passive solar system -Active solar systems - Water desalination - Output from solar still – Principle of solar ponds.
Unit-IIIWind Energy – Nature of wind – Characteristics – Variation with height and time – Power in wind –Aerodynamics of Wind turbine – Momentum theory – Basics of aerodynamics – Aerofoils and their characteristics – HAWT – Blade element theory – Prandtl’s lifting line theory (prescribed wake analysis) VAWT aerodynamics – Wind turbine loads – Aerodynamic loads in steady operation – Yawed operation and tower shadow.
Unit-IVWind Energy Conversion System – Siting – Rotor selection – Annual energy output – Horizontal axis wind turbine (HAWT) – Vertical axis wind turbine (VAWT) – Rotor design considerations – Number of blades – Solidity - Blade profile – Upwind/Downwind – Yaw system – Tower – Braking system -Synchronous and asynchronous generators and loads – Integration of wind energy converters to electrical networks – Inverters – Control system – Requirement and strategies – Noise – Applications of wind energy
![Page 19: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/19.jpg)
Unit-VBiomass energy - Bio fuel classification – Examples of thermo chemical, Pyrolysis, biochemical and agrochemical systems – Energy farming – Direct combustion for heat – Process heat and electricity – Ethanol production and use – Anaerobic digestion for biogas – Different digesters –Digester sizing – Applications of Biogas - Operation with I.C.Engine
Unit-VIOcean Energy - OTEC Principle - Lambert’s law of absorption - Open cycle and closed cycle - heat exchanger calculations – Major problems and operational experience.
Unit-VIITidal Power - Principles of power generation - components of power plant – Single and two basin systems – Turbines for tidal power - Estimation of energy – Maximum and minimum power ranges - tidal powerhouse. Wave Energy – Concept of energy and power from waves – Wave characteristics – period and wave velocities - Different wave energy conservation devices (Saltor duck, oscillating water column and dolphin types) – operational experience.
Unit-VIIIGeothermal Energy - Classification- Fundamentals of geophysics - Dry rock and hot aquifier energy analysis - Estimation of thermal power - Extraction techniques - Prime movers.
References:1. Renewable Energy Resources / John Twidell and Tony Weir / E & F.N.Spon2. Renewable Energy Resources Basic Principles and Applications / G.N.Tiwari and M.K.Ghosal /
Narosa3. Solar Energy - Principles of thermal collection and storage/ S.P. Sukhatme / TMH4. Solar Energy Thermal Processes,/Duffie & Beckman5. Solar Heating and Cooling / Kreith & Kreider6. Wind Energy Handbook / Tony Burton, David Sharpe, Nick Jenkins and Ervin Bossanyi /
WileyWind Electrical Systems / S.N.Bhadra, D.Kastha and S.Banerjee / Oxford7. Biogas Technology - A Practical Hand Book / K.Khendelwal & S.S. Mahdi / McGraw-Hill
![Page 20: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/20.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- I Semester
POWER ELELCTRONIC SYTEMS SIMULATION LAB
1. Switching characteristics of Thyristor, MOSFET,IGBT using PSPICE Simulation2. PSPICE Simulation of Single phase full converter using RL load with and without LC Filter.3. PSPICE Simulation of Single phase full converter using RL & E load with and without free
wheeling diode4. PSPICE Simulation of Three phase full converter using RL & E Loads.5. PSPICE Simulation of single phase AC Voltage controller with PWM control for RL load.6. PSPICE Simulation of three phase AC Voltage controller using RL load.7. PSPICE Simulation of single phase inverter with sinusoidal PWM control for R- load8. PSPICE Simulation of Three phase inverter with Sinusoidal PWM control for R-Load.9. PSPICE Simulation of single phase current source inverter with RL Load.10. PSPICE Simulation of dc-dc Boost converter.11. DC motor with controlled ac rectification using Matlab/Simulink12. Development and Simulation of 3-phase PWM Inverter with sinusoidal pulse-width modulation
using Matlab/Simulink13. Cascade position control of a DC motor drive (PI controller) using Matlab/Simulink14. Characteristics of induction machines under balanced and symmetrical conditions for the
following using Matlab/Simulinka. dq model in synchronous reference frame b. dq model in stator reference frame c. dq model in rotor reference frame
15. Volts/Hz closed-loop speed control of an induction motor drive using Matlab/Simulink16. Open-loop Volts/Hz control of a synchronous motor drive using Matlab/Simulink17. Speed control of a permanent magnet synchronous motor using Matlab/Simulink18. Capacitor-start capacitor-run single-phase induction motor using Matlab/Simulink19. Single phase IGBT based fully controlled rectifier with PWM control using Matlab-Simpower
blockset20. Three phase IGBT based ac voltage controller with PWM control using Matlab-Simpower
blockset
![Page 21: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/21.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
SWITCHED MODE POWER CONVERSION
Unit –I Single-switch Isolated converters:Requirement for isolation in the switch-mode converters, transformer connection, Forward and flyback converters, power circuit and steady-state analysis.
Unit-II: Push-Pull Converters: Power circuit and steady-state analysis, utilization of magnetic circuits in single switch and push-pull topologies.Unit- III: Isolated Bridge converters:Half bridge and full-bridge converters, Power circuit and steady-state analysis, utilization of magnetic
circuits and comparison with previous topologies.
Unit-IV: Dynamic Analysis of dc-dc converters: Formulation of dynamic equation of buck and boost converters, averaged circuit models, linearization technique, small-signal model and converter transfer functions.
Unit-V: Controller Design:Review of frequency-domain analysis of linear time-invariant systems, concept of bode plot, phase and gain margins, bandwidth, controller specifications, proportional(P), proportional plus integral (PI), proportional plus integral plus integral controller (PID), selection of controller parameters.Unit-VI: Resonant Converters:Classification of Resonant converters-Basic resonant circuits- Series resonant circuit-parallel resonant circuits- Resonant switches.Unit-VII:Quasi-Resonant Converters-I: Concept of Zero voltage switching, principle of operation, analysis of M-type and L-type Buck or boost Converters. Unit-VIII: Quasi-Resonant Converters-II: Concept of Zero current switching, principle of operation, analysis of M-type and L-type Buck or boost Converters.
Text Books:1. Fundamentals of Power Electronics – Robert Erickson and Dragon Maksivimovic, Springer
Publications. 2. Power Electronics–Issa Batarseh- John Wiely
Reference Books:
1. Elements of Power Electronics - Philip T.Krein – Oxford University Press2. Power Electronics, L. Umanand, Tata Mc-Graw Hill
![Page 22: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/22.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
POWER ELECTRONIC CONTROL OF AC DRIVESUnit-I: IntroductionReview of steady-state operation of Induction motor, Equivalent circuit analysis, torque-speed characteristics. Unit II: Voltage Source Inverter Fed Induction motor drivesScalar control- Voltage fed Inverter control-Open loop volts/Hz control-Speed control with slip regulation-Speed control with torque and Flux control-Current controlled voltage fed Inverter DriveUnit III Current Source Inverter Fed Induction motor drivesCurrent-Fed Inverter control-Independent current and frequency control-Speed and flux control in Current-Fed Inverter drive-Volts/Hz control of Current-Fed Inverter drive-Efficiency optimization control by flux program.Unit IV Slip power recovery schemesSlip-power recovery Drives-Static Kramer drive-Phasor diagram-Torque expression-Speed control of a Kramer drive-Static scherbius drive-Modes of operationUnit-V: Vector control of Induction Motor: Principles of vector control, Direct vector control, derivation of indirect vector control, implementation –block diagram; estimation of flux, flux weakening operation.Unit-VI: Control of Synchronous motor drives: Synchronous motor and its characteristics- Control strategies-Constant torque angle control- power factor control, constant flux control, flux weakening operation, Load commutated inverter fed synchronous motor drive, motoring and regeneration, phasor diagrams. UNIT-VII: PMSM and BLDC Drives:Characteristics of permanent magnet, synchronous machines with permanent magnet, vector control of PMSM- Motor model and control scheme. Modeling of PM brushless dc motor, drive scheme -Three-phase full wave Brushless dc motor -Sinusoidal type of Brushless dc motor - current controlled Brushless dc motor Servo drive UNIT-VIII: Variable Reluctance Motor DriveVariable Reluctance motor drives- Torque production in the variable reluctance motor -Drive characteristics and control principles - Current control variable reluctance motor servo drive
Text Book:1. Electric Motor Drives Modeling, Analysis & control -R. Krishnan- Pearson Education
Reference Books:
2. Modern Power Electronics and AC Drives –B. K. Bose-Pearson Publications-3. Power Electronics control of AC motors – MD Murphy & FG Turn Bull Pergman Press -
1st edition-1998 4. Fundamentals of Electrical Drives – G.K. Dubey – Narosa Publications -19955. Power Semiconductor drives- G.K. Dubey-Prentice hall
![Page 23: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/23.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
FLEXIBLE AC TRANSMISSION SYSTEMSUNIT-1: IntroductionFACTS Concepts: Transmission interconnections power flow in an AC system, loading capability limits, Dynamic stability considerations, importance of controllable parameters basic types of FACTS controllers, benefits from FACTS controllers.UNIT-I1: Static Shunt CompensationStatic shunt compensation: Objectives of shunt compensation, mid point voltage regulation voltage instability prevention, improvement of transient stability, Power oscillation damping. UNIT-I1I: Methods of controllable var generation:Variable impedance type static var generators: Thyristor Controlled and Thyristor Switched Reactor(TCR and TSR), Thyristor Switched Capacitor(TSC), Fixed Capacitor Thyristor Controlled Reactor Type Var Generator FC-TCR, Thyristor Switched Capacitor- Thyristor Controlled Reactor Type Var Generator; Switching converter type var generators, Hybrid var generators.UNIT-IV: SVC and STATCOMStatic Var Compensators: SVC and STATCOM-The Regulation Slope, Transfer Function and Dynamic Performance-Transient Stability Enhancement and Power Oscillation Damping; Comparison between STATCOM and SVC: V-I and V-Q Characteristics, Transient Stability, Response Time, Capability to Exchange Real Power, Operation with Unbalanced AC System, Loss Versus Var Output Characteristic.UNIT-V: Static Series Compensation Concept of series capacitive compensation, improvement of transient stability, power oscillation damping; Variable Impedance Type Series Compensators-GTO Thyristor-Controlled Series Capacitor-(GCSC), Thyristor-Switched Series Capacitor(TSSC), Thyristor-Controlled Series Capacitor(TCSC), Basic Operating Control Schemes For GCSC,TSSC and TCSC.UNIT-VI: Switching Converter Type Series CompensatorsStatic Synchronous Series Capacitor(SSSC), Transmitted Power Versus Transmission Angle Characteristic, Control Range and VA Rating, Capability to Provide Real Power Compensation, Internal Control; External Control for Series Reactive Compensators.UNIT-VII: Static Voltage and Phase Angle Regulators: TCVR and TCPAR: Voltage and Phase Angle Regulation, Power Flow Control by Phase Angle Regulators, Real and Reactive Loop Power Flow Control; Approaches to Thyristor –Controlled Voltage and Phase Angle Regulators(TCVRs and TCPARs)-Continuously Controllable Thyristor Tap Changers.UNIT-VIII: Unified Power Flow Controller (UPFC) Introduction: The Unified Power Flow Controller-Basic Operating Principles, Conventional Transmission Control Capabilities, Independent Real and Reactive Power Flow Control, Control Structure, Basic Control System for P and Q Control.References books:1. N.G.Hingorani & L.Gyugyi, Understanding FACTS: Concepts and Technology of Flexible AC Transmission Systems, IEEE Press, 1999. 2. X.P. Zang, C. Rehtanz and B. Pal, Flexible AC Transmission Systems: Modeling and Control, Birkhauser, 2006. 3. Y. H. Song and A. T. Johns, Flexible AC Transmission Systems, IET, 1999.
![Page 24: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/24.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
DIGITAL SIGNAL PROCESSING AND ITS APPLICATIONS
Unit-I: Introduction to Digital Signal Processing
Introduction -Linear time invariant systems- A Digital Signal Processing System, The sampling -quantization – Discrete time sequences – Discrete Fourier Transform (DFT), Fast Fourier Transform (FFT, Digital filters Decimation & Interpolation.
Unit-II: Digital filter structures
Block Diagram representation, Equivalent structures, Basic FIR Digital Filter structures, Basic IIR Digital Filter structures, Realization of Basic structures using MATLAB, All pass filters, Computational complexity of Digital filter structures.
UNIT III: IIR Digital filter design
Preliminary considerations, Bilinear transformation method of IIR Filter design, Design of low pass IIR Digital filters, Design of High pass, Band pass and band stop IIR digital filters, Spectral Transformations of IIR filter.UNIT IV: FIR digital filter design
Preliminary considerations, FIR filter design based on windowed Fourier series, Computer aided design of Equiripple Linear phase FIR filters, Design of Minimum phase FIR filters. Design of computationally efficient FIR digital filters.
Unit-V: Finite word Length effects
Introduction- Effects of coefficients on Quantization- Quantization in sampling analog signals- Finite register length effects in realization of Digital Filters- Discrete Fourier transform computations
Unit –VI: Architecture of TMS320LF 2407A
Introduction –Architectural overview – Memory and I/O spaces -Internal architecture – Central Processing Unit (CPU) – Program control.
Unit –VII: Addressing Modes and Assembly Language Instructions of C2xxx
Data formats – Addressing modes – groups of addressing mode – Assembly language instructions
Unit VIII: Peripherals (The Event Managers)
![Page 25: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/25.jpg)
Event Manager (EV) Functional Blocks-Event Manager (EV) Register Addresses- General-Purpose (GP) Timers -Compare Units- PWM Circuits Associated With Compare Units-PWM Waveform Generation With Compare Units and PWM Circuits-Space Vector PWM- Capture Units- Quadrature Encoder Pulse (QEP) Circuit - Event Manager (EV) Interrupts
References
1. Emmanuel C. Ifeachor, Barrie W. Jervis, “Digital Signal Processing: A Practical Approach”, Pearson Education India Series, New Delhi, 2nd Edition,2004
2. Sanjit K Mitra, “ Digital Signals Processing: A Computer Based Approach”, Tata McGraw- Hill Publishing Company Limited, 2nd Edition, 2004.
3. Alan Oppenheim. V and Ronald W.Schafer, “Digital Signal Processing”, Prentice Hall of India Private. Limited., New Delhi, 1989.
4. B.Venkatramani, M.Bhaskar “Digital Signal Processors- Architecture, programming and applications”, Tata McGraw- Hill Publishing Company Limited.
5. John G. Proakis and Manolakis. D.G, “Digital Signal Processing: Principles Algorithms and Applications,” Prentice Hall of India, New Delhi, 2004.
6. TMS320F/C24x DSP Controllers-Reference Guide-CPU and Instruction Set7. TMS320LF/LC240Xa-DSP Controllers-Reference Guide-System and Peripherals.
![Page 26: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/26.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
DIGITAL CONTROL SYSTEMS (Elective-III)UNIT-1: IntroductionAdvantages of Digital control systems- -Practical aspects of the choice of sampling rate and multirate sampling - Basic discrete time signals - Quantization – Sampling theorem -Data conversion and Quantization- Sampling process- Mathematical modeling- Data reconstruction and filtering of sampled signals – zero-order hold UNIT-II: Z-Transformsz- transform and inverse z-transform, Relationship between s- plane and z- plane- Difference equation-Solution by recursion and z-transform- pulse transfer functions of the zero-order Hold and relationship between G(s) and G(z)– Bilinear transformation .
UNIT-III: Z-Plane AnalysisDigital control systems- Pulse transfer function- z transform analysis of open loop, closed loop systems-Modified z- transfer function- Stability of linear digital control systems- Stability tests.Unit –IV State Space AnalysisState space representation of discrete time systems, pulse transfer function matrix, solving discrete time state space equations, state transition matrix and its properties methods for computation of state transition matrix, discretization of continuous time state-space equationsUnit-V Stability AnalysisStability analysis of closed loop systems in the Z-plane, Jury stability criterion test-Stability analysis by use of the bilinear transformation and routh stability criterion. Stability analysis using liapumov theoremsUnit-VI Design of Discrete Time control system by conventional methodsDesign of digital control systems based on Root locus techniques-Design of digital control based on the frequency response methods-Bilinear transformation and design procedure in the w-plane, lead, lag and Lead-lag compensators and digital PID controllers. Design digital control through dead beat response methods.Unit-VII State Feed back controllers and ObserversConcept of controllability and observability-Design of state feedback controller through pole placement-Necessary and sufficient conditions, Ackerman’s formula, State observers-Full order and Reduced Order observerUnit-VIII Linear Quadratic RegulatorsMin/Max principle, Linear Quadratic Regulators, Kalman Filters, State Estimation through kalman Filters, Introduction to adaptive controls Textbooks:
1. Discrete Time Control Systems-K.Ogata Pearson Education2. Digital Control systems and State Variables methods by M.Gopal
Reference Books1.Digital Control Engineering, Kuo, Oxford University2.Digital Control Engineering M.Gopal
![Page 27: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/27.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
INTELLIGENT CONTROL (Elective-III)
UNIT I:Introduction and motivation. Approaches to intelligent control. Architecture for intelligent control. Symbolic reasoning system, rule-based systems, the AI approach. Knowledge representation. Expert systems.
UNIT IIConcept of Artificial Neural Networks and its basic mathematical model, McCulloch-Pitts neuron model, simple perceptron, Adaline and Madaline, Feed-forward Multilayer Perceptron. Learning and Training the neural network.
UNIT IIIData Pre-Processing: Scaling, Fourier transformation, principal-component analysis and wavelet transformations. Networks: Hopfield network, Self-organizing network and Recurrent network. Neural Network based controller Case studies: Identification and control of linear and nonlinear dynamic systems using Matlab-Neural Network toolbox.
UNIT IVGenetic Algorithm: Basic concept of Genetic algorithm and detail algorithmic steps, adjustment of free parameters. Solution of typical control problems using genetic algorithm.
UNIT VConcept on some other than GA search techniques like tabu search and ant-colony search techniques for solving optimization problems.
UNIT VIIntroduction to crisp sets and fuzzy sets, basic fuzzy set operation and approximate reasoning. Introduction to Fuzzy logic modeling and control of a system. Fuzzification, inference and defuzzification. Fuzzy knowledge and rule bases. UNIT VIIFuzzy modeling and control schemes for nonlinear systems. Self-organizing fuzzy logic control. Implementation of fuzzy logic controller using Matlab fuzzy-logic toolbox.
Unit-VIII: Fuzzy logic & Neural network applications to DrivesFuzzy logic applications: Design of Fuzzy PI controller for speed control of DC motor- Flux programming efficiency improvement of three phase induction motor-Induction motor speed control-Slip gain tuning of indirect vector control of induction motor-stator resistance estimation.
![Page 28: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/28.jpg)
Neural network applications:-PWM Controller-Selected harmonic elimination PWM-Space vector PWM-Vector controlled drive-feedback signal estimation-speed estimation and flux estimation of induction motor
Text Books1. Neural Networks: A comprehensive Foundation – Simon Haykins, Pearson Edition,
2003.2. Fuzzy logic with Fuzzy Applications – T.J.Ross – Mc Graw Hill Inc, 1997.3. Genetic Algorithms- David E Goldberg.4. Modern Power Electronics and AC Drives –B.K.Bose-Pearson Publications5. Artificial Intelligent based Electrical Machines and Drives- Peter Vas, Oxford University Press
References1. Neural Network Design-M.T.Hagan, H. B. Demuth and M. Beale, Indian reprint, 2008.2. Principles of Neurocomputing for science and Engineering,- Fredric M.Ham and Ivica
Kostanic, McGraw Hill, 2001.3. Neural Network Fundamentals with Graphs, Algorithms and Applications, N.K. Bose and
P.Liang, Mc-Graw Hill, Inc. 1996.4. Intelligent System- Modeling, Optimization and Control- Yung C. Shin and Chengying
Xu,CRC Press, 2009.5. Soft computing & Intelligent Systems- Theory & Applications – N.K.Sinha and Modan
M Gupta. Indian Edition, Elsevier, 2007.6. Fuzzy logic Intelligence, Control, and Information- John Yen and Reza Langari, Pearson
Education, Indian Edition, 2003. 7. Fuzzy Control and Fuzzy Systms, Witold Pedrycz, Overseas Press, Indian Edition, 2008.
![Page 29: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/29.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
POWER QUALITY MANAGEMENT (Elective-IV)
Unit -I. Introduction To Power QualityWhat is Power Quality?, Voltage Quality, Why are we concerned about power quality?, The
power quality evaluation procedure-Need for a consistent-Vocabulary, General classes of power quality problems, Transients, Long-Duration voltage variations, Short-Duration voltage variations, Voltage Imbalance, waveform distortion, voltage fluctuation, Power frequency variations, Power quality terms, Ambiguous Terms, CBEMA and ITI curvesUnit- II. Power Frequency DisturbancesIntroduction-Common power frequency disturbances-Cures for low frequency disturbances-Voltage tolerance criteriaUnit III: Voltage Sags And InterruptionsSources of sags and interruptions-Estimating Voltage sag performance-Fundamental principles of protection-Solutions at the End-User level-Evaluating the economics of different ride_ through alternatives-Motor_ starting sags-Utility system fault_ clearing issuesUnit IV. Transient Over VoltagesSources of transient over voltages-Principles of over voltage protection-Devices for over voltage protection-Utility capacitor_ switching Transients-Utility system Lightning protection-Managing Ferroresonance-Switching Transients problems with loads-Computer tools for transient analysis.
Unit-V. Fundamentals Of HarmonicsHarmonic Distortion-Voltage versus current distortion-Harmonic versus Transients-Power system Quantities under non sinusoidal conditions-Harmonic indices-Harmonic sources from commercial loads-Harmonic sources from industrial loads-Locating harmonic sources-System response characteristics-Effects of harmonic distortion- Inter harmonics
Unit VI.Applied HarmonicsHarmonic distortion evaluations-Principles for controlling harmonics-Where to control harmonics-Harmonic study-Devices for controlling harmonic distortion-Harmonic filter design-Case studies-Standards on harmonicsUnit-VII. Long Duration Voltage VariationsPrinciples of regulating the voltage-Devices for voltage regulation-Utility voltage regulator application-Capacitors for voltage regulations-End user capacitor application-Regulating utility voltage with distributed resources-FlickersUnit VIII. Power Quality Monitoring
Monitoring considerations-Historical perspective of power quality measuring instruments-Power quality measurement equipment-Assessment of power quality measurement data-Application of intelligent systems-Power quality monitoring standardsReference books1.Electrical power systems quality-Roger C.Dugan- McGraw- Hills2.Power quality- C.Sankaran, CRC Press
![Page 30: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/30.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
ENERGY AUDITING, CONSERVATION & MANAGEMENT(Elective-IV)
Unit I : Basic Principles Of Energy AuditEnergy audit- definitions, concept , types of audit, energy index, cost index ,pie charts, Sankey diagrams, load profiles, Energy conservation schemes- Energy audit of industries- energy saving potential, energy audit of process industry, thermal power station, building energy audit
Unit II : Energy Management –IPrinciples of energy management, organizing energy management program, initiating, planning, controlling, promoting, monitoring, reporting
Unit III : Energy Management -IIEnergy manger, Qualities and functions, language, Questionnaire - check list for top management
Unit IV : Energy Efficient MotorsEnergy efficient motors , factors affecting efficiency, loss distribution , constructional details , characteristics - variable speed , variable duty cycle systems, RMS hp- voltage variation-voltage unbalance- over motoring- motor energy audit
Unit V : Power Factor Improvement, Lighting Power factor – methods of improvement , location of capacitors , Pf with non linear loads, effect of harmonics on p.f. , p.f motor controllers - Good lighting system design and practice, lighting control ,lighting energy audit
Unit VI : Energy InstrumentsEnergy Instruments- watt meter, data loggers, thermocouples, pyrometers,lux meters, tongue testers ,application of PLC’s
Unit VII : Economic Aspects And AnalysisEconomics Analysis-Depreciation Methods, time value of money, rate of return , present worth method , replacement analysis, life cycle costing analysis - Energy efficient motors
Unit VIII : Computation Of Economic AspectsCalculation of simple payback method, net present worth method- Power factor correction, lighting -Applications of life cycle costing analysis, return on investment .
TEXT BOOKS::
1. Energy management by W.R. Murphy & G. Mckay Butter worth, Heinemann publications. 2. Energy efficient electric motors by John .C. Andreas, Marcel Dekker Inc Ltd-2nd edition, 1995-REFERENCE BOOKS1. Energy management by Paul o’ Callaghan, Mc-graw Hill Book company-1st edition, 19982. Energy management hand book by W.C.Turner, John wiley and sons3. Energy management and good lighting practice : fuel efficiency- booklet12-EEO
![Page 31: M Tech Regulations and Syllabus](https://reader033.vdocuments.mx/reader033/viewer/2022051208/544bf72eaf7959ac438b57c9/html5/thumbnails/31.jpg)
w.e.f 2009-2010
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY: KAKINADADEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
(POWER and INDUSTRIAL DRIVES)M. Tech- II Semester
POWER ELECTRONICS AND DRIVES LABORATORY
List of experiments
1. Operation of 3- phase Full-Converter on R & R-L load.2. Performance & speed control of D.C. drive using 3-phase full Converter.3. Performance & Operation of a four quadrant Chopper on D.C. Drive4. Performance & Operation of a 3-phase A.C. Voltage controller on motor load.5. Single Phase IGBT based PWM Inverter on R & R-L load6. Operation of 3-phase IGBT based PWM Inverter on R & R-L load.7. Performance & speed control of 3 phase slip ring Induction motor by Static Rotor Resistance controller.8. Three phase PWM Pulse generation using PIC Micro controller9. PIC Microcontroller based speed control of three phase Induction Motor10. DSP based V/F Control of 3 phase Induction motor.