Download - Introduction to FMEA and FMECA in Design
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 1
“Buzz – is it a big deal?”
Why misunderstandings about environmental magnetic noise mustn’t prevent telecoil use
Revision 04
for: 2nd International Hearing Loop Conferenceby: Edworthy Audio Engineering Consultants
Tel: +44(0)1435 830195E-mail: [email protected]: www.edworthyaudio.com
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 2
Presentation structure
1. Categories of noise occasionally caused in hearing aids
2. How much noise is too much?3. What can I do about the noise?
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 3
What is this noise in the hearing aid?
3 categories of noise: -
Environmental radio-frequencyinterference (details in addendum)
Interference from the loop system itself (details in addendum)
Environmental magnetic interference
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 4
Is noise really a problem?
Many loop systems have no noise problemWhere there is noise, it can often be solved satisfactorily
The possibility of noise must not prevent audiologists dispensing telecoil-activated hearing aids
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 5
Environmental radio-frequencyinterference
What does it sound like?Tones, warbles, static (higher frequencies)Heard with both T and microphone position/programsHeard when loop system is not switched onFor more information on RF interference, please see addendum
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 6
Interference generated by the loop system itself
What does it sound like?Hum, Buzz, Crackles, WhistlesOnly heard with a hearing aid in the T position/programStops when loop system is switched offFor more information on interference generated by the loop itself, please see addendum
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 7
Environmental magneticinterference
What does it sound like?Hum, Buzzing, CracklesOnly heard with a hearing aid in the T position/programHeard even when loop system is switched off
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 8
Environmental magneticinterference
How is it caused?Any alternating electric current creates an alternating magnetic fieldThe same way an audio induction (hearing) loop system works
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 9
Environmental magneticinterference
Where does it come from?Badly installed AC power cablingAC power transformersElectric motorsElectric heating systemsCRT (tube) televisions/display monitorsFluorescent (strip) lightingLighting dimmersOther nearby loop systems
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 10
How much noise is too much?
Very subjective!For critical listening the noise level must be very lowWhere short-term communication is a priority, the noise level can be higherGenerally: If the noise spoils enjoyment or makes it difficult to understand speech, it is too noisy
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 11
How much noise is too much?
For those not using hearing-aids, how noisy is this venue?Demonstration of environmental magnetic
noise in this room
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 12
How much noise is too much?
International Standard IEC 60118-4 has technical requirements for environmental magnetic noise
Recommends maximum noise levels for different loop uses (critical listening and communication only)Requires measurements with ‘A’-weighted filteringMore technical details available in the addendum to this presentation
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 13
Over to Richard for the next slides
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 14
Case Studies (1)CRT (tube) display near ticket window causing buzz and hum
Re-positioned on desk, moved away from window = much reduced noise!Replaced with flat screen LCD/LED type = no noise!
Buzz and crackles from laser printerSwitched-off printer while loop is in use = no noise!
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 15
Case Studies (2)Buzz and hum from lighting power circuits because line & neutral (source & return) conductors take separate routes
AC power cabling re-installed with line & neutral conductors in same sheath = no noise!
Buzz and crackles from air conditioning plant equipment
Replaced thermostat devices with modern, low interference, types = no noise!
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 16
What can I do about the noise?Use hearing aid or receiver to locate source if possibleSwitch-off electrical equipment until noise stopsContact venue management
Alert them to Disability LegislationAlert them to potential loss of hearing aid users’ business
Contact owner of interference-generating equipment (e.g. power company)
Disability Legislation, Advocacy organisations?
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 17
What if noise level is too high and hearing assistance is still needed?Infrared or FM systems
Neck loops and silhouettes (ear hooks)They need telecoil in operation, so may pick up noiseSilhouette can overcome noise if hearing aid has volume control
Headphones must be suitable for hearing aid wearers
Direct audio inputAudio ‘shoe’, ‘boot’, etc.Bluetooth or other wireless technology if available for hearing aid
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 18
Review1. We’ve looked at causes of environmental magnetic
interference which can often be assessed and resolved quickly
2. We’ve described processes by which one can remedy magnetic interference present in the environment and who will need to be involved in that process.
3. We’ve described how compliance with the international standard for audio frequency induction loop systems addresses environmental magnetic interference
I hope we’ve convinced you that if noise is a problem, it can be overcome!
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 19
In conclusion
Thank you for listening!Was it a good presentation for you?
What went well?What could have gone better?What else do you want to know?
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 20
Contact details
Feel free to contact us at [email protected]@contactainc.com
Jensen Transformers’ websitewww.jensen-transformers.com/apps_wp.html
Look for Application Papers Jensen System Troubleshooting Guide AN003 AN004
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 21
Addendum
The following slides provide more information about the causes and cures for
Environmental radio-frequency interferenceInterference generated by the loop system itself
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 22
Environmental radio-frequencyinterference
How is it caused?Radio signals from cell-phones, radio and television transmitters, etc.Picked up by the internal circuitry of a hearing aid (not usually by the telecoil)
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 23
Environmental radio-frequencyinterference
Always likely to be some interference when very close to a transmitter (e.g. cell phone)Good design of hearing aid electronics can reduce sensitivity to RF interferenceRF interference not covered by the international loop standard
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 24
What can I do about this noise?
Simple:Move hearing aid away from transmitterMove transmitter away from hearing aid
Complex/expensive:Build metal ‘Faraday Cage’ around hearing aid user – not practical!Some RF shielding materials available that can be placed between cell phone and ear
Don’t wrap cell phone, that stops the cell phone working!
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 25
Interference generated by the loop system itself
How is it caused?Electrical noise picked up by amplifier input wiringCircuit noise from the amplifier itself (usually negligible)Self-oscillation, caused by some dynamic microphones and magnetic musical instrument pickupsGround (hum) loops and poor grounding practices
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 26
Noise generated by the loop system itself
Electrical noise pick up in amplifier input wiringUse balanced wiring interconnections (see Jensen Transformers website)Re-route/reconfigure cabling and connections
Circuit noise from the amplifier itselfBetter quality amplifier
What can I do about this noise?
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 27
What can I do about this noise?
Noise generated by the loop system itself
Self-oscillationRe-position dynamic microphones and magnetic musical instrument pickups away from loop
Ground (hum) loopsCure ground loop (see Jensen Transformers website)NEVER DISCONNECT SAFETY GROUNDGood grounding practices
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 28
How much noise is permitted by the International Standard?
IEC 60118-4: 2006Noise level measured in deciBels (dB)
DeciBel = tenth of a Bel1 Bel = log10(H1/H2)
H1 and H2 are two magnetic field strengths
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 29
How much noise is permitted by the International Standard?
Measured with reference to 400 mA/mOften called ‘dB L’
E.g.0 dB L = 400 mA/m (reference audio level)-22 dB L = 32 mA/m-32 dB L = 10 mA/m-47 dB L = 1.8 mA/m (equivalent to typical low acoustic background noise)
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 30
How much noise is permitted by the International Standard?
A-weighted noise level of -47 dB L recommended for quality audio-32 dB L and worse needs listening assessment
Soft hum can be acceptable, but harsh buzzing or loud tones are usually not acceptable
But no worse than -22 dB L
0 dBL
-47 dBL
-32 dBL
-22 dBL
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 31
How do we measure environmental magnetic interference?
Meter/receiver must use ‘A’-weighted filterMimics the ear’s changing sensitivity with frequencyLess sensitive at lower and higher frequencies
Must use meter with certain meter characteristics
True RMS reading/0.125 sec averaging time or PPMCalibrated in dB ref. 400 mA/m
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 32
How do we measure environmental magnetic interference?
Must orient the pick-up coil the same way as hearing aid telecoilsCheck the full 3-dimensional space in which hearing aids will be usedFrom
4 feet from floor for children and seated people,up to
5 feet 7 inches from floor for standing adults
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 33
Minimizing power system interference
The following 4 slides were prepared by John Woodgate of J.M.Woodgate and AssociatesThey help you understand why power system noise occursThey provide the rules that should be followed to minimize interference
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 34
Hum, buzz or‘power system interference’
Poorly-installed power wiring can form loops carrying mains current, generating magnetic fields that sound as hum or buzz in a hearing aid in T mode.
Appliance
Live
Neutral
Current ➔
Magnetic field
Separated Live and Neutral wires
© J.M.Woodgate and Associates
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 35
Ground loops – another source of hum
ApplianceLive and Neutral close
Ground
Magnetic fieldWrong!
Current splits
© J.M.Woodgate and Associates
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 36
Live wires: black, red
Neutral wires: white (grey)
Ground wires: green (green/yellow)
RULESMr. Black and Mr. Red always go with Mr. White in the same cable;
Mr. White and Mrs. Green must meet only once, at the service entrance.
Minimising magnetic field emissions from power wiring – American rules
© J.M.Woodgate and Associates
DGEA QT035_01(c) Edworthy Audio Engineering Consultants 37
Minimising magnetic field emissions from power wiring – European rulesLive wires: brown
Neutral wires: blue
Earth wires: green-yellow
RULESMr. Brown always goes with Mr. Blue in the same cable;
Mr. Blue and Mrs. Green-Yellow must meet only once, in the supplier’s wiring.
© J.M.Woodgate and Associates