EASA
Implementation Workshop on the Global Reporting Format for Runway Surface Conditions
ICAO EUR Region
Virtual event via Webex, 10 March 2021
Armann Norheim
Rapporteur ICAO Friction Task Force
ICAO Global Reporting System and Format
Creation
Creation of a global system and format
Need to standardise information to pilots
Operational need
Let there be no doubt.
• The ICAO global reporting system and format is developed based upon the operational need for information for the safe operation of the aircraft.
• Improved safety through performance-relevant reporting of runway conditions.
A global language.
A tool for making decisions.
Runway Condition Report (RCR)
A tool for making decisions
Three accidents
• 1958 – Munich, Germany (+ 1959 incident at Idlewild, New York, USA)• Brought the slush into sharp focus – ½ inch rule
• 1989 – Dryden, Ontario, Canada• exhaustive investigation ….., but also of the aviation system that allowed it to occur.’• JWRFMP
• 2006 – Midway, Chicago, USA• TALPA ARC
This methodology communicates actual runway conditions to pilots in terms that directly relate to expected aircraft performance.
1960’s – IATA proposal – MOTNE - SNOWTAM
• 1963 - IATA addressed concern and proposed a new reporting system and format – Snow plan – MOTNE (only network available)
• 1968 – SNOWTAM pro-forma
• Report - Subjective judgement heavily based/supported by measured friction coefficient.
• Global application? - No
JWRFMP (1995 – 2004+)
Angelo Boccanfuso1962 – 2016Transport Canada Development CentreJoint Winter Runway Friction Measurement Program 1995 – 2004 +
JWRFMP overall objective
• ….. device a better, more meaningful method for the pilot to determine landing and accelerated stopping distance requirements.
• Based upon, among others; recommendation (part of):
• …. technically accurate means of defining runway surface conditions and their effects on aircraft performance.
IMAPCR ‘99
• Review of ICAO documentation presented at ICAO HQ , Montreal through 16 Safety Barriers with a clear message to address the concern expressed:
• …. that ICAO address the discrepancies outlined
• …. that ICAO needs to address and clarify the documentation
AOSWG/1 – June 2005 Need to standardise information to pilots
(Chicago Midway - December 2005)
ICAO State letter - May 2006 – Questionnaire
FAA Workshop - August 2006
Aerodrome Panel - 1 December 2006
FAA – TALPA ARC - October 2007
AOSWG/5 – April 2008
ICAO Friction Task Force - April 2008
TALPA ARC transmitted proposals to FAA in April/May 2009 TALPA ARC closed in Nov 2009
TALPA initiative
FTF Phase 1 (2008 – 2011)
• Annex 14 and (Annex 15)
• Revised Reporting Procedure• Revised SNOWTAM
• Circular 329 – Assessment, Measurement and Reporting of Runway Surface Conditions
Since 14 November, 2013
No longer reporting µ
Friction measuring equipment values are no longer used to determine and report surface conditions because joint industry and multi-national government tests have not established a reliable correlation between runway friction values and the relationship to airplane braking performance.
FAA SAFO 19001 - Landing Performance Assessment at Time of Arrival, 11 March 2019
Research - Procedures Tests
FTF Phase 2 (2011 – 2020+)
• Global reporting system and format
4. November 2021
• Co-operation across Annex’s and Panels
That what makes this work so valuable
Air Navigation Commission JOB CARD ADOP.001
• Problem Statement:
• Runway surface conditions have contributed to many safety events and investigations have revealed shortfalls in the accuracy and timeliness of assessment and reporting methods currently provided for in ICAO provisions and guidance material.
Air Navigation Commission JOB CARD ADOP.001
• Pilots of modern aircraft also need reports that are directly related to the performance of the aircraft.
AMENDMENTS• Annex 3
• Annex 6, Part II
– Aeroplane Performance Manual (Doc 10064) New (2020)
• Annex 8
• Annex 11
– PANS ATM
• Annex 14, Vol I
– PANS Aerodromes
– Circular 329 – Revised → Circular 355 (March 2019)
• Annex 15
– PANS AIM – (Doc 10066) New (2018) (AIS-AIMSG)
All changes are (and must be) coordinated!
Affects
• Aircraft Manufacturers (Aircraft Flight Manual)
• Aircraft Operators (Operations Manual)
• Aerodrome Operators (Aerodrome Manual)
• Aeronautical Information Services (SNOWTAM)
• Air Traffic Services (ATIS/VOICE)
ALL: One language
Defined concept
• Definitions of terms define the fundamental, conceptual part of thereport and assessment of the runway surface conditionsmethodology.
• Based on the defined concept the RCR is a validated method that replaces subjective judgements with objective assessments that are directly tied to criteria relevant for aeroplane performance. These criteria have been determined by aeroplane manufacturers to cause specific changes in aeroplane braking performance.
Standardised information to pilots
Aeroplane performance calculation section
Information provided in standardised order.
Type of information identified by location in the information string.
Situational awareness section
Information provided in standardised order.
Each information ends with a . “full stop”
Operational need
The information
is being generated
in a standardised format
in order to meet an
operation need.
Runway Condition Report (RCR)
Challenges
•Implementation
•Training
•Technical issues/Programming
Willingness to change
Doc Hierarchy EuropeICAO
EASA
OPER
A14 A 8 A 6A 15 A 11
PANS AD
CS w AMC/GM
Part OPS965/2012
AIPNOTAM
SNOWTAM
PANS ATM
Part ADR139/2014
AMC/GM
AD Manual
A/C withTC
AFM
AMC/GM
OM A/B (C/D)
Part ATM/ANS2017/373
Part 25
ATISATC VOICE
AMC/GM/CS
PANS AIM
APMDoc
10064
SERA923/2012
A 3
AMC/GM
Operational needRCR Integrity RCR information
The information in the RCR – Why?
SAFE OPERATION OF
THE AEROPLANE