Download - Head losses
![Page 1: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/1.jpg)
![Page 2: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/2.jpg)
04/15/2023 2
• Danial Zafar Gondal 13-ME-027
• Ehtisham Qaiser 13-ME-031
• Faizan Shabbir 13-ME-032
• Asif Mehboob 13-ME-034
Group Members
![Page 3: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/3.jpg)
04/15/2023 3
• Definition
• Dimensional Analysis
• Types
• Darcy Weisbech Equation
• Major Losses
• Minor Losses
• Causes
Head Losses
![Page 4: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/4.jpg)
04/15/2023 Danial Gondal 4
• Head loss is loss of energy per unit
weight.
• Head = Energy of Fluid / Weight
• Head losses can be
– Kinetic Head
– Potential Head
– Pressure Head
Head Loss
![Page 5: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/5.jpg)
04/15/2023 5
• Kinetic Head
– K.H. = kinetic energy / Weight = v² /2g
• Potential Head
– P.H = Potential Energy / Weight = mgz /mg = z
• Pressure Head
– P.H = P/ ρ g
![Page 6: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/6.jpg)
04/15/2023 6
• (P/ ρ g) + (v² /2g ) + (z) = constant
• (FL-2F-1L3LT-2L-1T2) + (L2T-2L1T2)+(L) = constant
• (L) + (L) + (L) = constant• As L represent height so it is dimensionally L.
Dimensional Analysis
![Page 7: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/7.jpg)
04/15/2023 7
• However the equation (P/ ρ g) + (v² /2g ) + (z) = constant
Is valid for Bernoulli's Inviscid flow case. As we are studying viscous flow so
(P1/ ρ g) + (v1² /2g ) + (z1) = EGL1(Energy Grade Line At point 1)
(P2/ ρ g) + (v2² /2g ) + (z2) = EGL2(Energy Grade Line At point 2)
Head Loss
![Page 8: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/8.jpg)
04/15/2023 8
• For Inviscid Flow
EGL1 - EGL2= 0
• For Viscous Flow
EGL1 - EGL2= Hf
Head Loss
![Page 9: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/9.jpg)
MAJOR LOSSES IN
PIPES
![Page 10: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/10.jpg)
04/15/2023 10
•Friction loss is the loss of energy or “head” that occurs in pipe flow due to viscous effects generated by the surface of the pipe.• Friction Loss is considered as a "major loss" •In mechanical systems such as internal combustion engines, it refers to the power lost overcoming the friction between two moving surfaces.•This energy drop is dependent on the wall shear stress (τ) between the fluid and pipe surface.
Friction Loss
![Page 11: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/11.jpg)
04/15/2023 11
•The shear stress of a flow is also dependent on whether the flow is turbulent or laminar. •For turbulent flow, the pressure drop is dependent on the roughness of the surface. •In laminar flow, the roughness effects of the wall are negligible because, in turbulent flow, a thin viscous layer is formed near the pipe surface that causes a loss in energy, while in laminar flow, this viscous layer is non-existent.
Friction Loss
![Page 12: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/12.jpg)
04/15/2023 12
Frictional head losses are losses due to shear stress on the pipe walls. The general equation for head loss due to friction is the Darcy-Weisbach equation, which is where f = Darcy-Weisbach friction factor, L = length of pipe, D = pipe diameter, and V = cross sectional average flow velocity. This equation is valid for pipes of any diameter and for both laminar and turbulent flows.
Friction Loss
![Page 13: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/13.jpg)
04/15/2023 13
For Laminar Flow
Friction Loss
For Turbulent Flow
![Page 14: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/14.jpg)
MINOR LOSSES IN
PIPES
![Page 15: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/15.jpg)
• In addition to head loss due to friction, there are always other
head losses due to pipe expansions and contractions, bends,
valves, and other pipe fittings. These losses are usually known
as minor losses (hLm).
• In case of a long pipeline, the minor losses maybe negligible
compared to the friction losses, however, in the case of short
pipelines, their contribution may be significant.
![Page 16: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/16.jpg)
• Losses caused by fittings, bends, valves, etc…
![Page 17: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/17.jpg)
• Minor in comparison to friction losses which are considered major.
• Losses are proportional to – velocity of flow, geometry of device.
HL = K (v² /2g)
• The value of K is typically provided for various devices.
• Energy lost – units – m or ft• K - loss factor - has no units (dimensionless).
![Page 18: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/18.jpg)
where ,
HLm = minor loss
K = minor loss coefficient
V = mean flow velocity
g
VKhLm 2
2
Type K
Exit (pipe to tank) 1.0
Entrance (tank to pipe) 0.5
90 elbow 0.9
45 elbow 0.4
T-junction 1.8
Gate valve 0.25 - 25
Typical K values
Minor Losses Are Due to
![Page 19: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/19.jpg)
• As fluid flows from a smaller pipe into a larger pipe through
sudden enlargement, its velocity abruptly decreases; causing
turbulence that generates an energy loss.
• The amount of turbulence, and therefore the amount of
energy, is dependent on the ratio of the sizes of the two pipes.
Sudden Enlargement
![Page 20: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/20.jpg)
• Energy lost is because of turbulence. Amount of turbulence
depends on the differences in pipe diameters.
HL = K (v² /2g)
• The values of K have been experimentally determined and
provided in Figure and Table
![Page 21: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/21.jpg)
![Page 22: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/22.jpg)
![Page 23: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/23.jpg)
• Analytical expression of K - If the velocity v1 < 1.2 m/s or 4
ft/s, the K values can be given as :
K = [ 1-(A1/A2) ]² = [ 1-(D1/D2)² ]²
• As previous table consist of practical values therefore
theoretical formulas are different for different values &
above mentioned formula is applicable at 1.2 m/s velocity.
![Page 24: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/24.jpg)
• Decrease in pipe diameter
Note that the loss is related to the velocity in the second (smaller) pipe!
Sudden Contraction
![Page 25: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/25.jpg)
• The section at which the flow is the narrowest – Vena Contracta• At vena contracta, the velocity is maximum.
![Page 26: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/26.jpg)
Energy losses for sudden contraction are less than those for sudden enlargement.
![Page 27: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/27.jpg)
Comparison
![Page 28: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/28.jpg)
• Again a gradual contraction will lower the energy loss (as opposed to sudden contraction). θ is called the cone angle.
Gradual Contraction
![Page 29: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/29.jpg)
• Case of where pipe enters a tank – a very large enlargement.
• The tank water is assumed to be stationery, that is, the
velocity is zero.
• Therefore all kinetic energy in pipe is dissipated, therefore K
=1.0
Exit Loss
![Page 30: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/30.jpg)
• If the enlargement is gradual (as opposed to our previous
case) – the energy losses are less.
• The loss again depends on the angle of enlargement.
Gradual Enlargement
![Page 31: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/31.jpg)
Fluid moves from zero velocity in tank to v².
Entrance Losses
![Page 32: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/32.jpg)
04/15/2023 32
![Page 33: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/33.jpg)
04/15/2023 33
Head loss has several causes, including:
• Losses depend on the conditions of flow and the physical
properties of the system.
• Movement of fluid molecules against each other
• Movement of fluid molecules against the inside surface of a
pipe or the like, particularly if the inside surface is rough,
textured, or otherwise not smooth
• Bends and other sharp turns in piping
Causes
![Page 34: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/34.jpg)
04/15/2023 34
In pipe flows the losses due to friction are of two kinds:
• Skin-friction – This is due to the roughness of the inner part of the
pipe where the fluid comes in contact with the pipe material
• Form-friction – It is due to obstructions present in the line of flow
perhaps a bend, control valve, or anything that changes the course of motion of the flowing fluid.
Causes
![Page 35: Head losses](https://reader036.vdocuments.mx/reader036/viewer/2022062300/55b90fcbbb61ebad578b45d2/html5/thumbnails/35.jpg)
04/15/2023 35
THANK YOU…
ANY QUESTION PLEASE……???