2
Frequency Inverters
SJ700B SeriesPowerful Inverter for General Purpose Use
© 2015 Hitachi Europe GmbH · Specifications are subject to change without notice
SJ70
0B S
erie
s
*1 Starting torque
Series Applicable motor Starting torque
SJ700B7.5 to 75 kW 0.5 Hz / 150%90 to 160 kW 0.5 Hz / 120%
High performance, powerful functions, user friendly.
Improved Sensorless Vector Control and Auto Tuning allow for the easy setup of motor constants and enable a high starting torque of 150% or more at 0.5Hz.
The SJ700B inverter is a general purpose inverter which can also be applied to high torque applications.
A powerful drive with high starting torque and easy configuration
Using the DC bus AVR Function the deceleration time is con-trolled in order to avoid exceeding the over-voltage trip level. This enables trip-less operation.
Over voltage suppression
Trip avoidance functions
Higher internal calculation speed improves Current control performance.
Over-current suppression helps to avoid an inverter trip dur-ing acceleration, deceleration and impact loads.
Over current suppression
Motor Torque vs. Speed
Speed (min-1)
Torq
ue [
%]
Voltage of the main circuit DC
Motor current
Output frequency
Over-current suppression ONOver-current suppression OFF
300 600 900
-100-150
1200 1500 1800
0.5 Hz
150100
0
Suppresses over current and continues running
Impact LoadFrequency
OC-Trip
Motor Current
WJ2
00 S
erie
s
3
SJ700 B- 110 H F F
© 2015 Hitachi Europe GmbH · Specifi cations are subject to change without notice
SJ70
0B S
erie
s
130
120
110
100
90
80
70
60
50
40
30
20
10
0 150k 200k 500k 1M 2M 5M 7M 10M 20M 30M
EMC Filter & Brake Circuit integrated as standard
Cost and space can be reduced when compared to use of an external EMC Filter.
Built-in EMC Filter
F: Integrated EMC fi lter
F: With keypad
Power Source:
H: 3-phase 400V class
Applicable Motor Capacity:
075: 7.5 kW
1600: 160 kW
Series Name
Model Name Indication
Brake Circuit up to 30kW
Cost and Space reduction compared with external Braking Controller.
Example SJ700B 150 HFF
Lev
el [d
b]
Frequency [Hz]QP: Quasi Peak
EN61800-3 2nd Environment[C3]QP Limit Level
4
Frequency Inverters
SJ700B SeriesPowerful Inverter for General Purpose Use
© 2015 Hitachi Europe GmbH · Specifications are subject to change without notice
SJ70
0B S
erie
s
SJ300 series SJ700B series
Removable Control circuit terminals(Move to SJ700B without re-wiring)
Cooling fan(s) and DC bus capacitors can be easily removed for cleaning or replacement.
The removable Logic terminal block of SJ300/L300P are compatible with SJ700B. Re-wiring is not necessary.
The user can select from a number of parameter display modes.
• Data comparison function Displays only those parameters, which have been changed from the
default.
• User selected function Displays up to 12 user defined parameters (U001-U012)
• Basic mode (default) Displays commonly used parameters
The SJ700B inverters are fitted with a serial RS-485 Modbus-RTU port as standard. The inverters can be connected to the following fieldbus networks, using separately available option boards:
PROFIBUS-DB CanOPEN DeviceNet and other networks
Easy-removable Cooling Fan Easy-removable DC bus capacitors (SJ700B: above 18.5kW)
Easy Maintenance
Network compatibility
Easy Operation
Easy-removable components User defined display parameters
Various Fieldbus options available
The advanced design of the cooling fan(s) and the DC bus capacitors results in a calculated life time of 10 years*. The ON/OFF control function can extend the life time of the fan(s) even further.*Ambient temperature: SJ700B: 30° C (no corrosive gases, oil mist or dust)
Long Life time
Life time warning function
Long life time components
Through monitoring of the lifetime warning and other func-tions, preemptive component maintenance can be carried out to avoid unexpected system failures.
Networking Example
*1 Control circuit terminals comparison table
Series Input terminals Output terminalsSJ700B 9 terminals
(Intelligent 8 terminals, FW)5 terminals
(Open collector outputs)SJ300
L300P 6 terminals (Intelligent 5 terminals, FW)
2 terminals (Relay outputs)
Indication only Basic Parameter
Chose Basic Parameter
Basic Mode
5© 2015 Hitachi Europe GmbH · Specifi cations are subject to change without notice
SJ70
0B S
erie
s
Versatile Functions
Effective matching of output frequency and motor speed at restart, even without motor residual voltage.
Active frequency matching
The SJ700B ignores instantaneous fl uctuations in input power, as long as the DC bus voltage remains higher than the under- voltage trip level.
Instantaneous Power Failure - mask function
When AHD signal is switched on, output frequency set by the Analog signal is held constant. While AHD is on, frequency can be adjusted using the UP/Down function. In this mode, set frequency can be maintained after power shut down.
Analog Command – hold function
Instantaneous input power (kW) can be monitored. Useful for monitoring energy savings.
Integrated Input Power Monitor
The SJ700B detects motor current and automatically reduces the carrier frequency accordingly.
Automatic Carrier Frequency Adjustment
High resolution Analog output (10 bits)
Controlled deceleration and stop at power loss
The SJ700B outputs a disconnection signal when the frequency command via the analog input is lost.
Analog Input Disconnection - detection function
Various acceleration/deceleration curves can be selected depending on application requirements.
Acceleration/Deceleration curve function
Timer function can reduce the need for external timer circuits.
Intelligent IO terminals – ON/OFF Delay (Timer) function
Global standards
CE, UL, c-UL, c-Tick approvals.
Conformity to global standards
Logic input and output terminals can be configured for sink or source logic.
Logic input & output Terminal apply sink & source logic
Input voltage 480V for 400V class as standard.
Wide input power voltage range
Environmental Friendliness
Hitachi original PWM control method limits motor terminal voltage to less than twice the inverter DC bus voltage.
Micro surge voltage suppress function
Environment-friendly inverter meets RoHS requirements
EU RoHS compliant
Varnish coating of internal PC board & plating of main circuit copper bus bar are standard.
Improvement of environment
6
Frequency Inverters
SJ700B SeriesPowerful Inverter for General Purpose Use
© 2015 Hitachi Europe GmbH · Specifi cations are subject to change without notice
SJ70
0B S
erie
s
Symbol Name Explanation of Terminals Ratings
Anal
og
Power SupplyL
Common Terminal for Analog Power Source
Common terminal for H, O, O2, OI, AM, and AMI. Do not ground. –
HPower Source for Frequency Setting
Power supply for frequency command input DC 10V, 20mA max.
Frequency Setting
O Frequency Command TerminalMaximum frequency is attained at DC 10V in DC 0-10V range. Set the voltage at A014 to command maximum frequency below DC 10V.
Input impedance: 10kΩ, Allowable input voltage range: DC -0.3-+12V
O2Frequency Command Extra Terminal
O2 signal is added to the frequency command of O or OI in DC 0-±10V range. By changing confi guration, frequency command can be input also at O2 terminal.
Input impedance:10kΩ, Allowableinput voltage range: DC 0-±12V
OI Frequency Command TerminalMaximum frequency is attained at DC 20mA in DC 4-20mA range. When the intelligent terminal confi gured as AT is on, OI signal is enabled.
Input impedance: 100Ω, Allowable input voltage range: DC 0-24mA
Monitor Output
AM Analog Output Monitor (Voltage) Selection of one function from:Output frequency, output current, torque, output voltage, input power, electronic thermal load ratio, and LAD frequency. [DC0-10V output (PWM output)] Selection
DC 0-10V, 2mA max.
AMI Analog Output Monitor (Current) DC 4-20mA, 250Ω max.
Digi
tal
Monitor Output FM Digital Monitor (Voltage)
[DC0-10V output (PWM output)] Selection of one function from: Output frequency, output current, torque, output voltage, input power, electronic thermal load ratio, and LAD frequency.[Digital pulse output (Pulse voltage DC 0/10V)] Outputs the value of output frequency as digital pulse (duty 50%)
Digital output frequency range: 0-3.6kHz, 1.2mA max.
Power SupplyP24 Power Terminal for Interface
Internal power supply for input terminals. In the case of source type logic, common terminal for contact input terminals.
DC 24V, 100mA max.
CM1 Common Terminal for InterfaceCommon terminal for P24, TH, and FM. In the case of sink type logic, common terminal for contact input terminals. Do not ground.
–
ContactInput
Run Command
FW Forward Command InputThe motor runs forward when FW terminal is ON, and stops when FW is OFF.
[Input ON condition]Voltage between each terminal and PLC: DC 18V min.[Input OFF condition] Voltage between each terminal and PLC: DC 3V max.Input impedance between each terminal and PLC: 4.7ΩAllowable maximum voltage between each terminal and PLC: DC 27V
Functions
12345678
Intelligent Input TerminalsAssign 8 functions to terminals. (Refer to the standard specifi cations for the functions.)
CommonTerminal
PLC
Common Terminal for Intelligent Input Terminals, Common Terminal for External Power Supply for PLCs, etc.
Select sink or source logic with the short-circuit bar on the control terminals.Sink logic: Short P24 to PLC / Source logic: Short CM1 to PLC. When applying external power source, remove the short-circuit bar and connect PLC terminal to the external device.
Open Collector Output
State
1112131415
Intelligent Output Terminals
Assign 5 functions to open collector outputs.When the alarm code is selected at C062, terminal 11-13 or 11-14 are reserved for error codes of inverter trip.(Refer to the standard specifi cations for the functions.)Both sink and source logic are always applicable between each terminal and CM1.
Decrease in voltage between each terminal and CM2: 4V max. during ONAllowable maximum voltage: DC 27VAllowable maximum current: 50mA
CM2Common Terminal for Intelligent Output Terminals
Common terminal for intelligent output terminal 11-15.
Anal
og Analog Input
Sensor TH Thermistor Input Terminals
The inverter trips when the external thermistor detects abnormal temperature. Common terminal is CM1. [Recommended thermistor characteristics]Allowable rated power: 100mW or over. Impedance in the case of abnormal temperature: 3kΩNote: Thermal protection level can be set between 0 and 9999Ω.
Allowable input voltage range
[Input Circuit]
THThermistor
CM1
DC 0–8VDC 8V10kΩ
1kΩ
Digi
tal
Relay Output
State/Alarm
AL0AL1AL2
Alarm Output TerminalsIn default setting, an alarm is activated when inverter output is turned off by a protective function.
Maximum capacity of relays AL1-AL0: AC 250V, 2A (R load)/0.2A(L load)
DC 30V, 8A (R load)/0.6A(L load)AL2-AL0: AC 250V, 1A (R load)/0.2A(L load) DC 30V, 1A (R load)/0.2A(L load)Minimum capacity of relaysAL1-AL0, AL2-AL0: AC100V, 10mA DC5V, 100mA
Control Circuit Terminals
Terminal Description
Terminal Arrangement
H O2 AM FM TH FW 8 CM1 5 3 2 14 13 11 AL1L O OI AM1 P24 PLC CM1 7 6 4 2 15 CM2 12 AL0 AL2
Screw diameter: M3 Terminal Width: 6.4 mm
7© 2015 Hitachi Europe GmbH · Specifi cations are subject to change without notice
SJ70
0B S
erie
s
General SpecificationsItem General Specifi cations
Cont
rol
Control method Line to line sine wave pulse-width modulation (PWM) control
Output frequency range 0.1-400.0Hz
Frequency accuracy Digital: ±0.01% of the maximum frequency, Analog: ±0.2%(25±10°C)
Frequency resolution Digital setting: 0.01Hz, Analog setting: (Maximum frequency)/4,000 (O terminal: 12bit 0-10V, O2 terminal: 12bit -10-+10V)
V/f characteristics V/f optionally variable (30-400Hz of base frequency), V/f control (constant torque, reduced torque), Sensorless vector control, 0Hz domain sensor-less vector control, vector control (SJ-FB card option)
Speed fl uctuation ±0.5% (sensorless vector control)
Acceleration/deceleration time 0.01-3,600sec. (Linear/curve, accel./decel. selection), Two-stage accel./decel.
Starting Torque 150% at 0.5 Hz/ 90 kW and over: 120% at 0.5 Hz (With Sensorless vector control)
Carrier frequency range 0.5-12.0kHz (90kW and over: 0.5-8.0kHz)
DC braking Performs at start: under set frequency at deceleration, via an external input (braking force, time, and operating frequency).
Frequency setting
Operator Up and Down keys
External signal DC 0-10V, -10-+10V (input impedance 10k Ohmn), 4-20mA (input impedance 100 Ohmn)
External port Setting via RS485 Modbus-RTU communication
Forward /reverseStart /stop
Operator Start/stop commands (forward/reverse switching by parameter setting)
External signal Forward-operation start/stop commands (reverse-operation start/stop possible when relevant commands are assigned to intelligent input termi-nals) 3-wire input possible (when relevant commands are assigned to control circuit terminals)
External port Setting via RS485 Modbus-RTU communication
Inpu
t si
gnal Intelligent
input terminalsTerminals 8 terminals, NO/NC switchable, sink logic/source logic switchable
Functions 70 functions assignable to each terminal (for detail, refer to the instruction manual)
Thermistor input 1 terminal (PTC characteristics)
Out
put s
igna
l
Intelligentoutput terminals
Terminals 5 open-collector output terminals, NO/NC switchable, sink logic/source logic switchable 1 relay (1c-contact) output terminal: NO/NC switchable
Functions 51 functions assignable to each terminal (for detail, refer to the instruction manual)
Analog / Pulse output
Terminals Analog voltage output / Analog current output / Pulse-string output (PWM / Pulse train)
Functions 12 monitor functions assignable to each terminal
Monitoring on display Output frequency, output current, output torque, frequency conversion data, trip history, input/output terminal status, electric power, and others
Other functions
Free V/f setting (7 breakpoints), frequency upper/lower limit, jump (center) frequency, acceleration/deceleration according to characteristic curve, manual torque boost level/breakpoint, energy-saving operation, analog meter adjustment, start frequency setting, carrier frequency adjustment, electronic thermal function (available also for free setting), external start/end frequency/frequency rate, analog input selection, retry after trip, restart after instantaneous power failure, output of various signals, starting with reduced voltage, overload restriction, initial-value setting, auto-matic deceleration at power failure, AVR function, fuzzy acceleration/deceleration, online/offl ine auto-tuning, high-torque multi-motor operation (sensorless vector control of two motors by one inverter)
Protective functionsOvercurrent protection, overvoltage protection, undervoltage protection, electronic thermal protection, temperature error protection, instantaneous power failure protection, phase loss input protection, braking-resistor overload protection, ground-fault current detection at power-on, USP error, external trip, emergency stop trip, CT error, communication error, option board error, and others
Environ-mental conditions
Ambient operating/storagetemperature/ humidity Operating (ambient): -10-45°C / Storage: -20-65°C / Humidity: 20-90%RH (No condensation)
Location Altitude 1,000m or less, indoors (no corrosive gases or dust)
Options
Digital input expansion card SJ-DG (4digits BCD, 16bits binary)
Feedback expansion card SJ-FB (vector control loop speed sensor)
Network interface card SJ-DN2(DeviceNet(TM)), SJ-PB(T)2(PROFIBUS), SJ-CO (CANopen)
Others EMI fi lters, input/output reactors, braking resistors, braking units, communication cables
Standard Specifications SJ700B Series
3-phase 400V class
Model SJ700B- 075HFF 110HFF 150HFF 185HFF 220HFF 300HFF 370HFF 450HFF 550HFF 750HFF 900HFF 1100HFF 1320HFF 1600HFF
Enclosure (1) IP20 IP00
Applicable motor (4-pole, kW(HP)) (2) 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160
Output Ratings
Rated capacity (kVA)400V 11.0 15.2 20.0 25.6 29.7 39.4 48.4 58.8 72.7 93.5 110.8 135.1 159.3 200.9
480V 13.3 18.2 24.1 30.7 35.7 47.3 58.1 70.6 87.2 112.2 133 162.1 191.2 241.1
Rated output current (A) 16 22 29 37 43 57 70 85 105 135 160 195 230 290
Overload capacity (output current) 120%, 60sec
Rated output voltage (*3) 3-phase (3-wire) 380 to 480V (corresponding to input voltage)
Input Rating
Rated input voltage (V) 3-phase 380 to 480V +10%, -15%, 50/60Hz±5%
Rated input current (A) 18 24 32 41 47 63 77 94 116 149 176 199 253 300
BrakingDynamic braking (Short-time) (*4) Built-in BRD circuit (optional resistor) External dynamic braking unit (option)
Minimum value of resistor (Ω) 70 35 35 24 24 20 –
Vibration (*5) 5.9m/s2 (0.6G), 10-55Hz 2.9m/s2 (0.3G), 10-55Hz
EMC fi lter Built-in (EN61800-3 category C3)
Zero-phase Reactor Built-in
Weight (lbs.) 6 14 22 30 55 70
Hitachi Industrial Equipment Systems Co., Ltd., Tokyo
· SJ700B-075 – 150HFF
· SJ700B-370HFF
· SJ700B-185 – 300HFF
· SJ700B-450 – 750HFF
· SJ700B-900, 1100HFF · SJ700B-1320, 1600HFF
244
229
273.
4
376
390
24.5 80
229250
7916
479
(3.1
1)
2-7
9.5
83
190
368
510
540
195
79
45 80
2-10
265
310
700
670
480
380
2-12
250
7935
2
125 80
2- Ø7
203
82
170
13.6
7927
7
39025
0(9.
84)
2-12300
520
550
32.5 80 2- Ø12
2- Ø10
2- Ø12
130
255
241
150130
8025
140
62
189
210
24.5 80
7916
9
246
260
189
2-7
2- Ø7
143
2-6
2-Ø6
740
710
2- Ø12
480380
2-12
270(
10.6
3)
480
79
8062.5
390300
2-12
700
670
2- Ø12
270
357
79
8032.5
• SJ700-004~037 LFUF2, LFF2 • SJ700-007~040HFEF2, HFUF2, 007~037HFF2
• SJ700-150~220 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-185~300HFF
• SJ700-370~450 LFUF2,LFF2 • SJ700-370~550 HFEF2, HFUF2,HFF2• SJ700B-450~750HFF
• SJ700-300 LFUF2,LFF2 /HFEF2, HFUF2, HFF2• SJ700B-370HFF
• SJ700-550 LFUF2,LFF2
• SJ700-055~110 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-110~150HFF
* Please refer to page 30 for detailed information about compatibility with SJ300.
• SJ700-750, 900HFEF2, HFUF2, HFF2• SJ700B-900, 1100HFF
• SJ700-1100HFEF2, HFUF2, HFF2 / 1320HFEF2, HFF2, 1500HFUF2• SJ700B-1320, 1600HFF
244
229
273.
4
376
390
24.5 80
229250
7916
479
(3.1
1)
2-7
9.5
83
190
368
510
540
195
79
45 80
2-10
265
310
700
670
480
380
2-12
250
7935
2
125 80
2- Ø7
203
82
170
13.6
7927
7
390
250(
9.84
)
2-12300
520
550
32.5 80 2- Ø12
2- Ø10
2- Ø12
130
255
241
150130
8025
140
62
189
210
24.5 80
7916
9
246
260
189
2-7
2- Ø7
143
2-6
2-Ø6
740
710
2- Ø12
480380
2-12
270(
10.6
3)
480
79
8062.5
390300
2-12
700
670
2- Ø12
270
357
79
8032.5
• SJ700-004~037 LFUF2, LFF2 • SJ700-007~040HFEF2, HFUF2, 007~037HFF2
• SJ700-150~220 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-185~300HFF
• SJ700-370~450 LFUF2,LFF2 • SJ700-370~550 HFEF2, HFUF2,HFF2• SJ700B-450~750HFF
• SJ700-300 LFUF2,LFF2 /HFEF2, HFUF2, HFF2• SJ700B-370HFF
• SJ700-550 LFUF2,LFF2
• SJ700-055~110 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-110~150HFF
* Please refer to page 30 for detailed information about compatibility with SJ300.
• SJ700-750, 900HFEF2, HFUF2, HFF2• SJ700B-900, 1100HFF
• SJ700-1100HFEF2, HFUF2, HFF2 / 1320HFEF2, HFF2, 1500HFUF2• SJ700B-1320, 1600HFF
244
229
273.
4
376
390
24.5 80
229250
7916
479
(3.1
1)
2-7
9.5
83
190
368
510
540
195
79
45 80
2-10
265
310
700
670
480
380
2-12
250
7935
2
125 80
2- Ø7
203
82
170
13.6
7927
7
390
250(
9.84
)
2-12300
520
550
32.5 80 2- Ø12
2- Ø10
2- Ø12
130
255
241
150130
8025
140
62
189
210
24.5 80
7916
9
246
260
189
2-7
2- Ø7
143
2-6
2-Ø6
740
710
2- Ø12
480380
2-12
270(
10.6
3)
480
79
8062.5
390300
2-12
700
670
2- Ø12
270
357
79
8032.5
• SJ700-004~037 LFUF2, LFF2 • SJ700-007~040HFEF2, HFUF2, 007~037HFF2
• SJ700-150~220 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-185~300HFF
• SJ700-370~450 LFUF2,LFF2 • SJ700-370~550 HFEF2, HFUF2,HFF2• SJ700B-450~750HFF
• SJ700-300 LFUF2,LFF2 /HFEF2, HFUF2, HFF2• SJ700B-370HFF
• SJ700-550 LFUF2,LFF2
• SJ700-055~110 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-110~150HFF
* Please refer to page 30 for detailed information about compatibility with SJ300.
• SJ700-750, 900HFEF2, HFUF2, HFF2• SJ700B-900, 1100HFF
• SJ700-1100HFEF2, HFUF2, HFF2 / 1320HFEF2, HFF2, 1500HFUF2• SJ700B-1320, 1600HFF
244
229
273.
4
376
390
24.5 80
229250
7916
479
(3.1
1)
2-7
9.5
83
190
368
510
540
195
79
45 80
2-10
265
310
700
670
480
380
2-12
250
7935
2
125 80
2- Ø7
203
82
170
13.6
7927
7
390
250(
9.84
)
2-12300
520
550
32.5 80 2- Ø12
2- Ø10
2- Ø12
130
255
241
150130
8025
140
62
189
210
24.5 80
7916
9
246
260
189
2-7
2- Ø7
143
2-6
2-Ø6
740
710
2- Ø12
480380
2-12
270(
10.6
3)
480
79
8062.5
390300
2-12
700
670
2- Ø12
270
357
79
8032.5
• SJ700-004~037 LFUF2, LFF2 • SJ700-007~040HFEF2, HFUF2, 007~037HFF2
• SJ700-150~220 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-185~300HFF
• SJ700-370~450 LFUF2,LFF2 • SJ700-370~550 HFEF2, HFUF2,HFF2• SJ700B-450~750HFF
• SJ700-300 LFUF2,LFF2 /HFEF2, HFUF2, HFF2• SJ700B-370HFF
• SJ700-550 LFUF2,LFF2
• SJ700-055~110 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-110~150HFF
* Please refer to page 30 for detailed information about compatibility with SJ300.
• SJ700-750, 900HFEF2, HFUF2, HFF2• SJ700B-900, 1100HFF
• SJ700-1100HFEF2, HFUF2, HFF2 / 1320HFEF2, HFF2, 1500HFUF2• SJ700B-1320, 1600HFF
244
229
273.
4
376
390
24.5 80
229250
7916
479
(3.1
1)
2-7
9.5
83
190
368
510
540
195
79
45 80
2-10
265
310
700
670
480
380
2-12
250
7935
2
125 80
2- Ø7
203
82
170
13.6
7927
7
390
250(
9.84
)
2-12300
520
550
32.5 80 2- Ø12
2- Ø10
2- Ø12
130
255
241
150130
8025
140
62
189
210
24.5 80
7916
9
246
260
189
2-7
2- Ø7
143
2-6
2-Ø6
740
710
2- Ø12
480380
2-12
270(
10.6
3)
480
79
8062.5
390300
2-12
700
670
2- Ø12
270
357
79
8032.5
• SJ700-004~037 LFUF2, LFF2 • SJ700-007~040HFEF2, HFUF2, 007~037HFF2
• SJ700-150~220 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-185~300HFF
• SJ700-370~450 LFUF2,LFF2 • SJ700-370~550 HFEF2, HFUF2,HFF2• SJ700B-450~750HFF
• SJ700-300 LFUF2,LFF2 /HFEF2, HFUF2, HFF2• SJ700B-370HFF
• SJ700-550 LFUF2,LFF2
• SJ700-055~110 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-110~150HFF
* Please refer to page 30 for detailed information about compatibility with SJ300.
• SJ700-750, 900HFEF2, HFUF2, HFF2• SJ700B-900, 1100HFF
• SJ700-1100HFEF2, HFUF2, HFF2 / 1320HFEF2, HFF2, 1500HFUF2• SJ700B-1320, 1600HFF
244
229
273.
4
376
390
24.5 80
229250
7916
479
(3.1
1)
2-7
9.5
83
190
368
510
540
195
79
45 80
2-10
265
310
700
670
480
380
2-12
250
7935
2
125 80
2- Ø7
203
82
170
13.6
7927
7
390
250(
9.84
)
2-12300
520
550
32.5 80 2- Ø12
2- Ø10
2- Ø12
130
255
241
150130
8025
140
62
189
210
24.5 80
7916
9
246
260
189
2-7
2- Ø7
143
2-6
2-Ø6
740
710
2- Ø12
480380
2-12
270(
10.6
3)
480
79
8062.5
390300
2-12
700
670
2- Ø12
270
357
79
8032.5
• SJ700-004~037 LFUF2, LFF2 • SJ700-007~040HFEF2, HFUF2, 007~037HFF2
• SJ700-150~220 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-185~300HFF
• SJ700-370~450 LFUF2,LFF2 • SJ700-370~550 HFEF2, HFUF2,HFF2• SJ700B-450~750HFF
• SJ700-300 LFUF2,LFF2 /HFEF2, HFUF2, HFF2• SJ700B-370HFF
• SJ700-550 LFUF2,LFF2
• SJ700-055~110 LFUF2,LFF2 /HFEF2, HFUF2,HFF2• SJ700B-110~150HFF
* Please refer to page 30 for detailed information about compatibility with SJ300.
• SJ700-750, 900HFEF2, HFUF2, HFF2• SJ700B-900, 1100HFF
• SJ700-1100HFEF2, HFUF2, HFF2 / 1320HFEF2, HFF2, 1500HFUF2• SJ700B-1320, 1600HFF
Frequency Inverters
SJ700B SeriesPowerful Inverter for General Purpose Use
Hitachi Europe GmbH
Am Seestern 18 · D-40547 Düsseldorf Tel. +49-211-52 83 -0 · Fax +49-211-52 83 -649 Internet: www.hitachi-ds.comE-Mail: [email protected]
All features at a glance
BR
-SJ7
00B
-11
/13-E
N
333-B
W
Dimensions
Please call us!
[Unit: mm]
SJ70
0B S
erie
s
For more information about SJ700B Frequency Inverters, please scan this QR-Code with your smartphone.
Digital Operator
Digital Operator
Digital Operator
Digital Operator
Digital Operator
Digital Operator
Wall
Wall
Wall
Wall
Wall
Wall
Air intake
Air intake
Air intake
Air intake
Air intake
Air intake
Exhaust
Exhaust
Exhaust
Exhaust
Exhaust
Exhaust
3-33x28 Wiring Hole
5-Ø25Wiring Hole
3-42x42,5 Wiring Hole
5-Ø41Wiring Hole