FORD
© 2015 ATRA All Rights Reserved
113
5R110WCodes P0720, P0721, P0722, P0715, P0717, P0718, P0791, P0793, P0794Codes P0720 and P0722 indicates an insufficient , noisy or no input from the OSS. Codes P0715 and P0717 indicate an insufficient, noisy or no input from the TSS. Codes P0791 and P0793 indicate an insufficient, noisy or no input from the ISS.
OSS
TSS/ISS
© 2015 ATRA All Rights Reserved
FORD114
5R110WCodes P0720 and P0722 (continued)
FORD
© 2015 ATRA All Rights Reserved
115
5R110WCodes P0720 and P0722 (continued)
© 2015 ATRA All Rights Reserved
FORD116
5R110WCodes P0720 and P0722 (continued)There are two ways of checking the sensors with the scan tool monitor the PID readings or graph the signals. When checking the sensor signals with the scan tool you might miss glitches in the signal.
FORD
© 2015 ATRA All Rights Reserved
117
5R110WCodes P0720 and P0722 (continued)Using the graphing meter on the scan tool in much more efficient in capturing glitches.
© 2015 ATRA All Rights Reserved
FORD118
5R110WCodes P0720 and P0722 (continued)With the sensor disconnected connect the OSS with your meter. Then jump a 12 V fused link the hall effect sensor and monitor the signal as shown below.
FORD
© 2015 ATRA All Rights Reserved
119
5R110WCodes P0720 and P0722 (continued)You can also check the signal with the sensor connected. Back probe pin 2 at the harness connector.
© 2015 ATRA All Rights Reserved
FORD120
5R110WCodes P0720 and P0722 (continued)You can check the signal at the PCM connector to verify the signal is strong at the PCM and at the sensor.
FORD
© 2015 ATRA All Rights Reserved
121
5R110WCodes P0720 and P0722 (continued)Using a graphing meter on any speed sensor is always the best. Here we’re using it on the TSS/ISS sensor. Jump a 12 V fused link the hall effect sensor and monitor the signal as shown below.
© 2015 ATRA All Rights Reserved
FORD122
5R110WCodes P0720 and P0722 (continued)You can also check the signal with the sensor connected. Back probe pins 3 & 4 at the harness connector.
800-940-0197www.wittrans.com
Automatic Transmission Parts
Hard Parts• OE Manufacturer, Aftermarket New,
Remanufactured, & Used• Drums• Shafts• Pumps• Planets• Valve Bodies• Complete Line of Miscellaneous parts
Torque Converters• Complete line of CVC Remanufactured
Converters
Soft Parts• Master Kits• Banner Kits (Less Steels)• Overhaul Kits• Paper/Rubber Kits• Filters & Kits• Frictions• Steels• Bushings• Washers• Bearings• Gaskets• Bands• Flex Plates & Flywheels• Coolers• TeckPak Conversion Kits• Superior Shift Correction Packages• Transgo Reprogramming Kits• Transgo Shift Kits
Standard Transmission Parts• Rebuild Kits• Bearing Kits with Syncro Rings• Gasket Sets• Gears & Shafts
Rebuilt Transmissions• Standards
Clutch Parts• Sach’s & Valeo Clutch Kits (New)• Forks• Pilot Bushings & Bearings• Clutch Alignment Tools
Transfer Case Parts• Gasket & Seals Kits• Overhaul Kits• Chains
Shop Supplies & Tools• Additives• Assembly Lubricants• Builders Benches• Lifts• Parts Washer Soap• Rough Service Light Bulbs• R.T.V. Black, Blue, Clear• Technical Manuals• Tools & Equipment• Threadlock
For quicker access & more info, including our Tranny Guide™, ask for our CD Catalog. With clickable links to take you from index, to complete photo layout, to individual part
descriptions instantly!
Version 5.02015
DigitalCatalog
© 2015 ATRA All Rights Reserved
FORD124
5R110WCodes P0720 and P0722 (continued)You can check the signal at the PCM connector to verify the signal is strong at the PCM and at the sensor.
FORD
© 2015 ATRA All Rights Reserved
125
5R110WCodes P0720 and P0722 (continued)The scan tool and graphing meter are good tools but they can’t beat an oscilloscope. Oscilloscopes can find almost all glitches, noise or insufficient voltages.
© 2015 ATRA All Rights Reserved
FORD126
5R110WCodes P0720 and P0722 (continued)You can also check the signal with the sensor connected. Back probe pins 3 & 4 at the harness connector.
FORD
© 2015 ATRA All Rights Reserved
127
5R110WCodes P0720 and P0722 (continued)You can check the signal at the PCM connector to verify the signal is strong at the PCM and at the sensor.