![Page 1: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/1.jpg)
FET Biasing
1
![Page 2: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/2.jpg)
Introduction
For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockley’s equation.
Nonlinear functions results in curves as obtained for transfer characteristic of a JFET.
Graphical approach will be used to examine the dc analysis for FET because it is most popularly used rather than mathematical approach
The input of BJT and FET controlling variables are the current and the voltage levels respectively
2
![Page 3: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/3.jpg)
JFETs differ from BJTs:
Nonlinear relationship between input (VGS) and output (ID) JFETs are voltage controlled devices, whereas BJTs are
current controlled
Introduction
3
![Page 4: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/4.jpg)
Common FET Biasing Circuits• JFET
– Fixed – Bias – Self-Bias – Voltage-Divider Bias
• Depletion-Type MOSFET– Self-Bias– Voltage-Divider Bias
• Enhancement-Type MOSFET– Feedback Configuration– Voltage-Divider Bias
Introduction
4
![Page 5: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/5.jpg)
General Relationships For all FETs:
For JFETs and Depletion-Type MOSFETs:
For Enhancement-Type MOSFETs:
AIG 0
SD II
2
P
GSDSSD )
V
V(1II
2)( TGSD VVkI
5
![Page 6: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/6.jpg)
Fixed-Bias Configuration The configuration includes the ac levels Vi and Vo and
the coupling capacitors. The resistor is present to ensure that Vi appears at the
input to the FET amplifier for the AC analysis.
6
![Page 7: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/7.jpg)
Fixed-Bias Configuration For the DC analysis,
Capacitors are open circuits and
The zero-volt drop across RG permits replacing RG by a short-circuit AIG 0 VRARIV GGGRG 0)0(
7
![Page 8: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/8.jpg)
Fixed-Bias Configuration
Investigating the input loop
IG=0A, therefore
VRG=IGRG=0V
Applying KVL for the input loop,
-VGG-VGS=0
VGG= -VGS
It is called fixed-bias configuration due to VGG is a fixed
power supply so VGS is fixed
The resulting current,2)1(
P
GSDSSD V
VII
8
![Page 9: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/9.jpg)
Investigating the graphical approach. Using below tables, we can draw the graph
VGS ID
0 IDSS
0.3VP IDSS/2
0.5 IDSS/4
VP 0mA
9
![Page 10: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/10.jpg)
The fixed level of VGS has been superimposed as a
vertical line at
At any point on the vertical line, the level of VG is -VGG---
the level of ID must simply be determined on this vertical
line.
The point where the two curves intersect is the common
solution to the configuration – commonly referrers to as
the quiescent or operating point.
The quiescent level of ID is determine by drawing a
horizontal line from the Q-point to the vertical ID axis.
GGGS VV
10
![Page 11: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/11.jpg)
Output loop
DDDDDS RIVV
VVS 0
SDDS VVV
SDSD VVV 0SV
DSD VV
SGGS VVV
SGSG VVV 0SV
GSG VV
11
![Page 12: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/12.jpg)
Example
Determine VGSQ, IDQ, VDS, VD, VG, VS
12
![Page 13: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/13.jpg)
Exercise
Determine IDQ, VGSQ, VDS, VD, VG and VS
13
![Page 14: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/14.jpg)
Self Bias Configuration The self-bias configuration eliminates the need for two
dc supplies. The controlling VGS is now determined by the voltage
across the resistor RS
14
![Page 15: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/15.jpg)
For the indicated input loop:
Mathematical approach:
rearrange and solve.
SDGS RIV
2
2
1
1
P
SDDSSD
P
GSDSSD
V
RIII
V
VII
15
![Page 16: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/16.jpg)
Graphical approach Draw the device transfer characteristic Draw the network load line
Use to draw straight line.First point,Second point, any point from ID = 0 to ID = IDSS. Choose
the quiescent point obtained at the intersection of the straight line plot and the device characteristic curve.
The quiescent value for ID and VGS can then be determined and used to find the other quantities of interest.
SDGS RIV 0,0 GSD VI
2
2
SDSSGS
DSSD
RIV
thenI
I
16
![Page 17: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/17.jpg)
17
![Page 18: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/18.jpg)
For output loopApply KVL of output loopUse ID = IS
RDDDSDSD
SDS
DSDDDDS
VVVVV
RIV
RRIVV
)(
18
![Page 19: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/19.jpg)
19
![Page 20: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/20.jpg)
ExampleDetermine VGSQ, IDQ,VDS,VS,VG and VD.
20
![Page 21: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/21.jpg)
ExampleDetermine VGSQ, IDQ, VD,VG,VS and VDS.
21
![Page 22: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/22.jpg)
Voltage-Divider Bias The arrangement is the same as BJT but the DC analysis is different In BJT, IB provide link to input and output circuit, in FET VGS does
the same
22
![Page 23: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/23.jpg)
Voltage-Divider Bias The source VDD was separated into two equivalent sources to permit
a further separation of the input and output regions of the network.
IG = 0A ,Kirchoff’s current law requires that IR1= IR2 and the series
equivalent circuit appearing to the left of the figure can be used to find the level of VG.
23
![Page 24: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/24.jpg)
21
DD2G
RR
VRV
SDGGS
RSGSG
RIVV
VVV
0
Voltage-Divider Bias
VG can be found using the voltage divider rule :
Using Kirchoff’s Law on the input loop:
Rearranging and using ID =IS:
Again the Q point needs to be established by
plotting a line that intersects the transfer curve.24
![Page 25: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/25.jpg)
Procedures for plotting
1. Plot the line: By plotting two points: VGS = VG, ID =0 and VGS = 0, ID = VG/RS
2. Plot the transfer curve by plotting IDSS, VP and calculated values of ID.
3. Where the line intersects the transfer curve is the Q point for the circuit.25
![Page 26: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/26.jpg)
Once the quiescent values of IDQ and VGSQ are determined, the
remaining network analysis can be found.
Output loop:
2121 RR
VII DDRR
)( SDDDDDDS RIRIVV
DDDDD RIVV
SDS RIV
26
![Page 27: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/27.jpg)
Effect of increasing values of RS
27
![Page 28: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/28.jpg)
ExampleDetermine IDQ, VGSQ, VD, VS, VDS and VDG.
28
![Page 29: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/29.jpg)
ExampleDetermine IDQ, VGSQ, VDS, VD and VS
29
![Page 30: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/30.jpg)
Depletion-type MOSFET bias circuits are similar to JFETs. The only difference is that the depletion-Type MOSFETs can operate with positive values of VGS and with ID values that exceed IDSS.
Depletion-Type MOSFETs
30
![Page 31: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/31.jpg)
The DC Analysis Same as the FET calculations
Plotting the transfer characteristics of the device Plotting the at a point that VGS exceeds the 0V or more positive values Plotting point when VGS=0V and ID=0A The intersection between Shockley characteristics and linear
characteristics defined the Q-point of the MOSFET
The problem is that how long does the transfer characteristics have to be draw? We have to analyze the input loop parameter relationship. As RS become smaller, the linear characteristics will be in narrow slope
therefore needs to consider the extend of transfer characteristics for example of voltage divider MOSFET,
The bigger values of VP the more positive values we should draw for the transfer characteristics
SDGGS
RSGSG
RIVV
VVV
0
Depletion-Type MOSFETs
31
![Page 32: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/32.jpg)
Analyzing the MOSFET circuit for DC analysis
How to analyze dc analysis for the shown network? It is a …. Type network Find VG or VGS
Draw the linear characteristics
Draw the transfer characteristics
Obtain VGSQ and IDQ from the graph intersection
32
![Page 33: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/33.jpg)
1. Plot line for VGS = VG, ID = 0 and ID = VG/RS, VGS = 0
2. Plot the transfer curve by plotting IDSS, VP and calculated values of ID.
3. Where the line intersects the transfer curve is the Q-point.Use the ID at the Q-point to solve for the other variables in the voltage-divider bias
circuit. These are the same calculations as used by a JFET circuit.
33
![Page 34: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/34.jpg)
When RS change…the linear characteristics will change..
1. Plot line for VGS = VG, ID = 0 and ID = VG/RS, VGS = 0
2. Plot the transfer curve by plotting IDSS, VP and calculated values of ID.
3. Where the line intersects the transfer curve is the Q-point.
Use the ID at the Q-point to solve for the other variables in the voltage-divider bias
circuit. These are the same calculations as used by a JFET circuit.
34
![Page 35: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/35.jpg)
The transfer characteristic for the enhancement-type MOSFET is very different from that of a simple JFET or the depletion-typeMOSFET.
Enhancement-Type MOSFET
35
![Page 36: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/36.jpg)
Transfer characteristic for E-MOSFET
and
2)( )( ThGSGSD VVkI
2)()(
)(
)( ThGSonGS
onD
VV
Ik
36
![Page 37: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/37.jpg)
Feedback Biasing Arrangement
IG =0A, therefore VRG = 0V
Therefore: VDS = VGS
Which makes DDDDGS RIVV
37
![Page 38: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/38.jpg)
1. Plot the line using VGS = VDD, ID = 0 and ID = VDD / RD and VGS = 0
2. Plot the transfer curve using VGSTh , ID = 0 and VGS(on), ID(on); all given in the
specification sheet.3. Where the line and the transfer curve intersect is the Q-Point.4. Using the value of ID at the Q-point, solve for the other variables in the bias
circuit.
Feedback Biasing Q-Point
38
![Page 39: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/39.jpg)
DC analysis step for Feedback Biasing Enhancement type MOSFET
Find k using the datasheet or specification given;
ex: VGS(ON),VGS(TH)
Plot transfer characteristics using the formula
ID=k(VGS – VT)2. Three point already defined that is ID(ON), VGS(ON) and VGS(TH)
Plot a point that is slightly greater than VGS Plot the linear characteristics (network bias line) The intersection defines the Q-point
39
![Page 40: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/40.jpg)
ExampleDetermine IDQ and VDSQ for network below
40
![Page 41: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/41.jpg)
Again plot the line and the transfer curve to find the Q-point.Using the following equations:
21
DD2G
RR
VRV
)( DSDDDDS
SDGGS
RRIVV
RIVV
Input loop :
Output loop :
Voltage-Divider Biasing
41
![Page 42: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/42.jpg)
1. Plot the line using VGS = VG = (R2VDD)/(R1 + R2), ID = 0 and ID = VG/RS
and VGS = 0
2. Find k
3. Plot the transfer curve using VGSTh, ID = 0 and VGS(on), ID(on); all given in the specification sheet.
4. Where the line and the transfer curve intersect is the Q-Point.
5. Using the value of ID at the Q-point, solve for the other variables in the bias circuit.
Voltage-Divider Bias Q-Point
42
![Page 43: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/43.jpg)
ExampleDetermine IDQ and VGSQ and VDS for
network below
43
![Page 44: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/44.jpg)
== -
-
=-=
- + )(
=
= -+
= - )( +
==
-)( ++ -
== 44
![Page 45: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/45.jpg)
=-==
= -
= -= -
=+-=
= - +( )
== -
=
=+-
45
![Page 46: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/46.jpg)
Troubleshooting
N-channel VGSQ will be 0V or negative if properly checked
Level of VDS is ranging from 25%~75% of VDD. If 0V indicated, there’s problem
Check with the calculation between each terminal and ground. There must be a reading, RG will be excluded
46
![Page 47: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/47.jpg)
For p-channel FETs the same calculations and graphs are used, except that the voltage polarities and current directions are the opposite. The graphs will be mirrors of the n-channel graphs.
P-Channel FETs
47
![Page 48: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/48.jpg)
• Voltage-Controlled Resistor
• JFET Voltmeter
• Timer Network
• Fiber Optic Circuitry
• MOSFET Relay Driver
Practical Applications
48
![Page 49: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/49.jpg)
JFET Voltmeter
49
![Page 50: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/50.jpg)
Advantages
High Input impedance for isolation.Amount of power drawn from circuit under
test is very small, so no loading effect.Very high sensitivity.Amplifier gain allows measurement in the
mV range.No damage due to overload because of
amplifier saturation.
50
![Page 51: FET Biasing 1. Introduction For the JFET, the relationship between input and output quantities is nonlinear due to the squared term in Shockleys equation](https://reader035.vdocuments.mx/reader035/viewer/2022062307/55173aaa550346fe558b6102/html5/thumbnails/51.jpg)
Single MOSFET Relay Toggle Circuit
51