FAKULTI TEKNOLOGI KEJURUTERAANUNIVERSITI MALAYSIA PERLIS
SEMESTER 2 2013/2014
PLT 108 - ENGINEERING SKILLS IIMODULE : COMPUTER
NAME : ……………………………………………..
MATRIC NUMBER : ……………………………………………..
PROGRAMME : …………………………………………….. Marks:
DATE : ……………………………………………..
CHECKED BY : ……………………………………………..
CO3 : Ability to apply and construct the basic skills and standard practicedof computer assembly and networking
SUBJECT: ENGINEERING SKILLS II
FAKULTI TEKNOLOGI KEJURUTERAANPLT 108
Prepared by MOHD ANNUAR BIN MOHD ISA 2013/2014
W I N D O W S & F O R M A T T I N G P a g e | 2
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
CORE DESCRIPTIONStudents will learn necessary competencies for an entry-level IT professional including
formatting, windows and drivers installation & troubleshooting.
OBJECTIVES
To be able to perform partition and format hard drive
To be able to perform clean and upgrade installation of operating systems.
1. INTRODUCTION TO OPERATING SYSTEM(OS)
An OS is a program which acts as an interface between computer system users and the
computer hardware. It provides a user-friendly environment in which a user may easily
develop and execute programs. Otherwise, hardware knowledge would be mandatory for
computer programming. So, it can be said that an OS hides the complexity of hardware
from uninterested users.
In general, a computer system has some resources which may be utilized to solve a
problem such as memory, processors, i/o devices, file system as so on. The OS manages
these resources and allocates them to specific programs and users. An OS provides
services for:
Processor Management
Memory Management
File Management
Device Management
Concurrency Control
Figure 1.1 Hardware-software interaction through OS
W I N D O W S & F O R M A T T I N G P a g e | 2
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
CORE DESCRIPTIONStudents will learn necessary competencies for an entry-level IT professional including
formatting, windows and drivers installation & troubleshooting.
OBJECTIVES
To be able to perform partition and format hard drive
To be able to perform clean and upgrade installation of operating systems.
1. INTRODUCTION TO OPERATING SYSTEM(OS)
An OS is a program which acts as an interface between computer system users and the
computer hardware. It provides a user-friendly environment in which a user may easily
develop and execute programs. Otherwise, hardware knowledge would be mandatory for
computer programming. So, it can be said that an OS hides the complexity of hardware
from uninterested users.
In general, a computer system has some resources which may be utilized to solve a
problem such as memory, processors, i/o devices, file system as so on. The OS manages
these resources and allocates them to specific programs and users. An OS provides
services for:
Processor Management
Memory Management
File Management
Device Management
Concurrency Control
Figure 1.1 Hardware-software interaction through OS
W I N D O W S & F O R M A T T I N G P a g e | 2
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
CORE DESCRIPTIONStudents will learn necessary competencies for an entry-level IT professional including
formatting, windows and drivers installation & troubleshooting.
OBJECTIVES
To be able to perform partition and format hard drive
To be able to perform clean and upgrade installation of operating systems.
1. INTRODUCTION TO OPERATING SYSTEM(OS)
An OS is a program which acts as an interface between computer system users and the
computer hardware. It provides a user-friendly environment in which a user may easily
develop and execute programs. Otherwise, hardware knowledge would be mandatory for
computer programming. So, it can be said that an OS hides the complexity of hardware
from uninterested users.
In general, a computer system has some resources which may be utilized to solve a
problem such as memory, processors, i/o devices, file system as so on. The OS manages
these resources and allocates them to specific programs and users. An OS provides
services for:
Processor Management
Memory Management
File Management
Device Management
Concurrency Control
Figure 1.1 Hardware-software interaction through OS
W I N D O W S & F O R M A T T I N G P a g e | 3
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Based on Figure 1.1, OS is used as predefined library for hardware-software interaction.
This is why, system programs apply to the installed OS since they cannot reach hardware
directly.
The most popular operating systems today include versions of Microsoft Windows (like
Windows 8, Windows 7, Windows Vista, and Windows XP), Apple's Mac OS, and flavors
of the open source operating system Linux.
2. WINDOWS OPERATING SYSTEM
Windows OS is the most widely used operating system for desktop and laptop computers.
Developed by Microsoft, Windows primarily runs on x86-based computers (the ubiquitous
PC), although versions have run on Intel's 64-bit Itanium CPUs. Windows provides a
graphical user interface and desktop environment in which applications are displayed in
resizable, movable windows on screen.
The first version of Windows introduced in 1985 is the "MS-DOS Executive," which was a
DOS application that ran applications in side-by-side windows. It barely made a dent in the
market. Since then, Microsoft continue to upgrade and release multiple version of
Windows notably Windows 98, Windows NT, Windows 2000, Windows XP, Windows 7
and newly released Windows 8.
3. PREPARATION : BEFORE WE BEGIN
In order to perform windows installation and basic networking, you need to make sure you
obtained all the following:
I. A workstation (Complete PC)
II. Windows XP Installation CD
III. Acer Veriton 7600G Driver & Utilities Installation CD
IV. Microsoft Office 2007 (optional)
V. Switch or Hub
VI. Straight-through network cable
VII. Crossover network cable
W I N D O W S & F O R M A T T I N G P a g e | 4
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
4.1.Objectives Identify various editions of Windows Operating System (OS).
Boot selection media such as DVD/CD, floppy or USB, install from image,
Recovery CD, Factory recovery partition.
Format installation options – clean install and upgrade.
Installation procedure of Windows OS and Microsoft Office software
4.2.PC Requirements
First of all make sure that your system can run Windows XP. The minimum PC
requirements for running Windows XP are:
Pentium 233-megahertz (MHz) processor or faster (300 MHz is recommended)
At least 64 megabytes (MB) of RAM (128 MB is recommended)
At least 1.5 gigabytes (GB) of available space on the hard disk
CD-ROM or DVD-ROM drive
Video adapter and monitor with Super VGA (800 x 600) or higher resolution
4.3.Choosing Windows Operating System(OS)
Before performing Windows OS installation, you must identify the version of your
Windows XP. As with all editions of Windows, Windows XP comes in different product
versions. Basically there are 6 editions of Windows XP to date which are:
Windows XP Starter Edition, for new computer users in developing countries
Windows XP Home Edition, for home desktops and laptops
Windows XP Home Edition N, as above, but without a default installation of
Windows Media Player, as mandated by an EU ruling
Windows XP Professional, for business and power users (Version number: NT
5.1.2600)
Windows XP Professional N, as above, but without a default installation of
Windows Media Player, as mandated by an EU ruling
Windows XP Professional x64 Edition, for PCs with x86-64 processors (based
on Windows Server 2003)
Windows XP Tablet PC Edition, for notebooks with a touch screen or a pen-
sensitive screen
4. Format, Install & Configure Windows Operating Systems and Software
W I N D O W S & F O R M A T T I N G P a g e | 5
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Each edition of Windows XP comes in 32-bit and 64-bit version OS. The edition you
have will be printed on your install DVD. Most new PCs now come with the 64 bit
version of the operating system pre-installed, however there can be a downside. While
the 64 bit versions of Windows offer better security and stability, there is still hardware
and software that won‘t run on it.
4.4.Windows Installation Guidelines
Before performing installation of Windows, you need to determine whether you want to
perform a clean install or a repair install. A clean install will delete all the files on your
drive and you will also have to reinstall all of your programs. If you have files on your
computer that aren’t backed up then you should opt for a repair installation. This will
keep all your files intact. The repair installation will fixed damage done to your system
files, however any problems that exist on your PC unrelated to system file may also be
there after installation.
Not every edition of Windows will allow you to repair, some will force you to do a clean
install. It is always a good idea to back up all your files and data first.
STEP 1 Boot your PC and press DEL/F2 to enter CMOS Setup. Make sure your
CMOS is set to boot from the DVD/CD ROM drive.
STEP 2 Insert Windows XP Installation Disc inside your PC drive. Exit and save
CMOS setting. PC will automatically reboot.
STEP 3 Press any key when asked to do so. Then the installation will begin by
loading the necessary files.
W I N D O W S & F O R M A T T I N G P a g e | 6
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.1 Windows loading the necessary files for installation
STEP 4 The “Welcome to Setup” screen appears with the option of Continuing Setup,
Repair a previous installation, or Quitting. For a clean install, press ENTER
to continue Setup.
Note:You may also choose R to Repair, or F3 to Quit and reboot the system.
Repair option is use to repair damage done to the system of previous
installation.
Figure 4.2 Windows XP main setup screen
STEP 5 The “Windows XP Licensing Agreement” screen will appear, otherwise
known as “EULA,” displays the legal in’s and out’s of this particular Windows
package. You may press F8 to signify that you agree with the terms, hit ESC
if you do not agree and PAGE UP or PAGE DOWN to scroll through each
screen.
Note: If you do not agree to the terms, setup will quit and reboot the system.
W I N D O W S & F O R M A T T I N G P a g e | 7
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.3 Windows XP Licensing Agreement or EULA screen
STEP 6 Installed hard drive partition information will be shown with the option to
create new partition or delete partition. Delete partition available in the list
one by one by pressing D and press ENTER on the next screen to confirm
deletion. Deletion can be cancel by pressing ESC at the confirmation screen.
Figure 4.4 Hard drive partition information screen
STEP 7 If all partition has been deleted, there will be one unpartitioned space on the
screen. Create TWO partitions from the space by pressing C. Enter in the
partition size in MB within the displayed minimum and maximum. Press
ENTER to create the partition.
Note: A small portion (approximately 8MB) will be unavailable to partition.
This is normal.
W I N D O W S & F O R M A T T I N G P a g e | 7
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.3 Windows XP Licensing Agreement or EULA screen
STEP 6 Installed hard drive partition information will be shown with the option to
create new partition or delete partition. Delete partition available in the list
one by one by pressing D and press ENTER on the next screen to confirm
deletion. Deletion can be cancel by pressing ESC at the confirmation screen.
Figure 4.4 Hard drive partition information screen
STEP 7 If all partition has been deleted, there will be one unpartitioned space on the
screen. Create TWO partitions from the space by pressing C. Enter in the
partition size in MB within the displayed minimum and maximum. Press
ENTER to create the partition.
Note: A small portion (approximately 8MB) will be unavailable to partition.
This is normal.
W I N D O W S & F O R M A T T I N G P a g e | 7
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.3 Windows XP Licensing Agreement or EULA screen
STEP 6 Installed hard drive partition information will be shown with the option to
create new partition or delete partition. Delete partition available in the list
one by one by pressing D and press ENTER on the next screen to confirm
deletion. Deletion can be cancel by pressing ESC at the confirmation screen.
Figure 4.4 Hard drive partition information screen
STEP 7 If all partition has been deleted, there will be one unpartitioned space on the
screen. Create TWO partitions from the space by pressing C. Enter in the
partition size in MB within the displayed minimum and maximum. Press
ENTER to create the partition.
Note: A small portion (approximately 8MB) will be unavailable to partition.
This is normal.
W I N D O W S & F O R M A T T I N G P a g e | 8
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.5 Creating partition
STEP 8 Choose drive C: or Partition1 to install the Windows. You may choose
ENTER to Install to the selected partition, D to Delete the highlighted
Partition, or F3 to Quit and reboot the system. Press ENTER.
Figure 4.6 Selecting partition for Windows installation
STEP 9 Select what format you wish to use by pressing the UP ARROW and DOWN
ARROW keys. Since this OS supports NTFS, format the partition with it. If
you do not, many folder and file security features will be unavailable. Press
ENTER to confirm your selection and Continue.
W I N D O W S & F O R M A T T I N G P a g e | 9
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.7 Format the partition
STEP 10 Windows installation will begin and it may take a while for setup to copy
various system files to the hard drives.
Figure 4.8 Windows XP installation setup progress bar
STEP 11 The first reboot and the end of the blue background has arrived. If you are
impatient, press ENTER to Restart before the 15 seconds expire. ENTER to
Restart the Computer is the only option available.
W I N D O W S & F O R M A T T I N G P a g e | 9
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.7 Format the partition
STEP 10 Windows installation will begin and it may take a while for setup to copy
various system files to the hard drives.
Figure 4.8 Windows XP installation setup progress bar
STEP 11 The first reboot and the end of the blue background has arrived. If you are
impatient, press ENTER to Restart before the 15 seconds expire. ENTER to
Restart the Computer is the only option available.
W I N D O W S & F O R M A T T I N G P a g e | 9
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.7 Format the partition
STEP 10 Windows installation will begin and it may take a while for setup to copy
various system files to the hard drives.
Figure 4.8 Windows XP installation setup progress bar
STEP 11 The first reboot and the end of the blue background has arrived. If you are
impatient, press ENTER to Restart before the 15 seconds expire. ENTER to
Restart the Computer is the only option available.
W I N D O W S & F O R M A T T I N G P a g e | 10
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.9 System reboot after completion
STEP 12 After reboot the new Windows XP boot screen is displayed and setup will
then continue the installation of Windows XP. It may take a while.
Figure 4.10 Windows installation screen
STEP 13 When prompted with options of configuring your Region and Input
Languages. Change the region setting by clicking on the Customize…
button. Proceed with clicking Next.
W I N D O W S & F O R M A T T I N G P a g e | 10
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.9 System reboot after completion
STEP 12 After reboot the new Windows XP boot screen is displayed and setup will
then continue the installation of Windows XP. It may take a while.
Figure 4.10 Windows installation screen
STEP 13 When prompted with options of configuring your Region and Input
Languages. Change the region setting by clicking on the Customize…
button. Proceed with clicking Next.
W I N D O W S & F O R M A T T I N G P a g e | 10
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.9 System reboot after completion
STEP 12 After reboot the new Windows XP boot screen is displayed and setup will
then continue the installation of Windows XP. It may take a while.
Figure 4.10 Windows installation screen
STEP 13 When prompted with options of configuring your Region and Input
Languages. Change the region setting by clicking on the Customize…
button. Proceed with clicking Next.
W I N D O W S & F O R M A T T I N G P a g e | 11
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.11 Regional and Language Options screen
STEP 14 The next screen will ask for your details. Enter in your Name and optional
Organization information, and then select the Next button.
Figure 4.12 User information details
STEP 15 Genuine Windows XP comes with a Product Key usually located on the back
of the sleeve of the CD. If you are reformatting using a Windows XP CD that
came with your computer, the product key may be located on a sticker
somewhere on your computer case. Enter your unique 25 digit Product Key
that came with your CD, then select the Next button.
W I N D O W S & F O R M A T T I N G P a g e | 11
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.11 Regional and Language Options screen
STEP 14 The next screen will ask for your details. Enter in your Name and optional
Organization information, and then select the Next button.
Figure 4.12 User information details
STEP 15 Genuine Windows XP comes with a Product Key usually located on the back
of the sleeve of the CD. If you are reformatting using a Windows XP CD that
came with your computer, the product key may be located on a sticker
somewhere on your computer case. Enter your unique 25 digit Product Key
that came with your CD, then select the Next button.
W I N D O W S & F O R M A T T I N G P a g e | 11
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.11 Regional and Language Options screen
STEP 14 The next screen will ask for your details. Enter in your Name and optional
Organization information, and then select the Next button.
Figure 4.12 User information details
STEP 15 Genuine Windows XP comes with a Product Key usually located on the back
of the sleeve of the CD. If you are reformatting using a Windows XP CD that
came with your computer, the product key may be located on a sticker
somewhere on your computer case. Enter your unique 25 digit Product Key
that came with your CD, then select the Next button.
W I N D O W S & F O R M A T T I N G P a g e | 12
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.13 Product Key confirmation screen
STEP 16 At the next screen, you will be asked to enter your Computer Name and
Administrator password. Choose one that meets your needs.
Note: It is VERY IMPORTANT that you keep this information safe and
remember what it is! Think of something secure and never lose or forget it.
You will not able to log in Windows if you forgot these details.
Figure 4.14 Username and password setting
W I N D O W S & F O R M A T T I N G P a g e | 12
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.13 Product Key confirmation screen
STEP 16 At the next screen, you will be asked to enter your Computer Name and
Administrator password. Choose one that meets your needs.
Note: It is VERY IMPORTANT that you keep this information safe and
remember what it is! Think of something secure and never lose or forget it.
You will not able to log in Windows if you forgot these details.
Figure 4.14 Username and password setting
W I N D O W S & F O R M A T T I N G P a g e | 12
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.13 Product Key confirmation screen
STEP 16 At the next screen, you will be asked to enter your Computer Name and
Administrator password. Choose one that meets your needs.
Note: It is VERY IMPORTANT that you keep this information safe and
remember what it is! Think of something secure and never lose or forget it.
You will not able to log in Windows if you forgot these details.
Figure 4.14 Username and password setting
W I N D O W S & F O R M A T T I N G P a g e | 13
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
STEP 17 Configure the proper information for the Date, Time and Time Zone at the
next screen.
Figure 4.15 Date and Time Zone setting
STEP 18 Select Typical Setting at the next screen and proceed by pressing Next.
Figure 4.16 Network setting
W I N D O W S & F O R M A T T I N G P a g e | 13
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
STEP 17 Configure the proper information for the Date, Time and Time Zone at the
next screen.
Figure 4.15 Date and Time Zone setting
STEP 18 Select Typical Setting at the next screen and proceed by pressing Next.
Figure 4.16 Network setting
W I N D O W S & F O R M A T T I N G P a g e | 13
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
STEP 17 Configure the proper information for the Date, Time and Time Zone at the
next screen.
Figure 4.15 Date and Time Zone setting
STEP 18 Select Typical Setting at the next screen and proceed by pressing Next.
Figure 4.16 Network setting
W I N D O W S & F O R M A T T I N G P a g e | 14
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.17 Configure computer domain for networking
STEP 19 Choose workgroup or domain name. If you are not a member of a domain
then leave the default settings and press Next. Windows will restart again
and adjust the display.
Figure 4.18 Windows XP boot screen
STEP 20 Finally Windows will start and present you with a Welcome screen. Click next
to continue. Configure the next few screens to your preferences and click
Finish when done.
W I N D O W S & F O R M A T T I N G P a g e | 14
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.17 Configure computer domain for networking
STEP 19 Choose workgroup or domain name. If you are not a member of a domain
then leave the default settings and press Next. Windows will restart again
and adjust the display.
Figure 4.18 Windows XP boot screen
STEP 20 Finally Windows will start and present you with a Welcome screen. Click next
to continue. Configure the next few screens to your preferences and click
Finish when done.
W I N D O W S & F O R M A T T I N G P a g e | 14
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.17 Configure computer domain for networking
STEP 19 Choose workgroup or domain name. If you are not a member of a domain
then leave the default settings and press Next. Windows will restart again
and adjust the display.
Figure 4.18 Windows XP boot screen
STEP 20 Finally Windows will start and present you with a Welcome screen. Click next
to continue. Configure the next few screens to your preferences and click
Finish when done.
W I N D O W S & F O R M A T T I N G P a g e | 15
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.19 Windows XP Welcome Screen
STEP 20 Finally, log in to your computer for the first time!
Figure 4.20 Windows XP start menu
STEP 20 You now need to check the device manager to confirm that all the drivers
have been loaded or if there are any conflicts. From the start menu select
Start > Settings > Control Panel. Click on the System icon and then from
the System Properties window select the Hardware tab, then click on
Device Manager
W I N D O W S & F O R M A T T I N G P a g e | 16
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
Figure 4.21 Windows Device Manager
Your hardware should come with manufacturer supplied drivers. You need to install these
drivers using the automatic setup program provided by the manufacturer or you need to
manually install these drivers. If you do not have the drivers, check the manufacturer’s
website to download them. To install a driver manually use the following procedure:
(a) From the device manager double click on the device containing the exclamation
mark.
(b) This would open a device properties window.
(c) Click on the Driver tab.
(d) Click Update Driver button. The Wizard for updating device driver pops up as
shown below:
Figure 4.22 Hardware Update Wizard menu
W I N D O W S & F O R M A T T I N G P a g e | 17
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
You now get two options. The first option provides an automatic search for the required
driver. The second option allows you to specify the location of the driver. If you don't know
the location of the driver, choosing the automatic search which would find the required
driver from the manufacturer supplied CD or Floppy disk. Windows would install the
required driver and may ask you to restart the system for the changes to take effect. Use
this procedure to install drivers for all the devices that contain an exclamation mark.
Windows is completely setup when there are no more exclamation marks in the device
manager.
4.5. Installing Additional Software: Microsoft Office 2007
Microsoft Office 2007 (officially called 2007 Microsoft Office System), also called MS Office
2007, is a Windows version of the Microsoft Office System. It is a world leading application
suites widely used for businesses and individual users who need professional-level
productivity applications. This software suite is an essential to perform word processing,
database recording, web management and many more. To perform the installation for MS
Office 2007, follow the guidelines below:
STEP 1 Insert the Microsoft Office 2007 Enterprise DVD/CD. If the Setup Wizard
does not automatically begin, then click Start > Run > D:\setup.exe (if your
DVD/CD drive letter is D:\)
STEP 2 Enter the Product Key from the back of the CD jacket. Note: This is a unique
code. Click Continue.
Figure 4.23 Product Key Validation process
W I N D O W S & F O R M A T T I N G P a g e | 18
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
STEP 3 Check the box "I accept the terms of this agreement" and click the
Continue button.
Figure 4.24 License Agreement Confirmation screen
Step 4 Choose an installation option, Upgrade (removes Office 2003) or Customize(keeps Office 2003 installed and adds Office 2007, allowing you to use them
both).
Figure 4.25 Installation option screen
W I N D O W S & F O R M A T T I N G P a g e | 19
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
STEP 5 Click Install Now and installation will begin. It may take 15-30 minutes to
finish.
Figure 4.26 Installation progress bar
STEP 6 Installation is now finished. Click Close to complete the installation.
Figure 4.27 Installation complete
W I N D O W S & F O R M A T T I N G P a g e | 20
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
5. Exploring & Navigating Microsoft Disk Operating System (MS-DOS)
5.1.Objectives Describe the importance of using MS-DOS.
Interfacing with DOS with basic commands.
Managing files in DOS.
5.2.Microsoft Disk Operating System(DOS)
MS-DOS controls the computer’s hardware and provides an environment for programs
to run. This system program must always be present when working with your computer.
There are a variety of reasons why you need MS-DOS. A few of them are listed below:
i. Controls the flow of information between you and the computer (translator).
ii. Allows you to store and retrieve information on your computer.
iii. Gives you access to all its function (i.e. saving, copying, and printing files).
iv. Interprets and translates the software you have on your computer.
5.3.MS-DOS Prompt
DOS is basically a command-line method of executing basically the same functions
available in Windows. User interface of MS-DOS (called Command Prompt) can be
accesed in Windows by:
1. Click Start2. Type cmd and press enter.
Figure 5.1 Command Prompt
W I N D O W S & F O R M A T T I N G P a g e | 20
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
5. Exploring & Navigating Microsoft Disk Operating System (MS-DOS)
5.1.Objectives Describe the importance of using MS-DOS.
Interfacing with DOS with basic commands.
Managing files in DOS.
5.2.Microsoft Disk Operating System(DOS)
MS-DOS controls the computer’s hardware and provides an environment for programs
to run. This system program must always be present when working with your computer.
There are a variety of reasons why you need MS-DOS. A few of them are listed below:
i. Controls the flow of information between you and the computer (translator).
ii. Allows you to store and retrieve information on your computer.
iii. Gives you access to all its function (i.e. saving, copying, and printing files).
iv. Interprets and translates the software you have on your computer.
5.3.MS-DOS Prompt
DOS is basically a command-line method of executing basically the same functions
available in Windows. User interface of MS-DOS (called Command Prompt) can be
accesed in Windows by:
1. Click Start2. Type cmd and press enter.
Figure 5.1 Command Prompt
W I N D O W S & F O R M A T T I N G P a g e | 20
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
5. Exploring & Navigating Microsoft Disk Operating System (MS-DOS)
5.1.Objectives Describe the importance of using MS-DOS.
Interfacing with DOS with basic commands.
Managing files in DOS.
5.2.Microsoft Disk Operating System(DOS)
MS-DOS controls the computer’s hardware and provides an environment for programs
to run. This system program must always be present when working with your computer.
There are a variety of reasons why you need MS-DOS. A few of them are listed below:
i. Controls the flow of information between you and the computer (translator).
ii. Allows you to store and retrieve information on your computer.
iii. Gives you access to all its function (i.e. saving, copying, and printing files).
iv. Interprets and translates the software you have on your computer.
5.3.MS-DOS Prompt
DOS is basically a command-line method of executing basically the same functions
available in Windows. User interface of MS-DOS (called Command Prompt) can be
accesed in Windows by:
1. Click Start2. Type cmd and press enter.
Figure 5.1 Command Prompt
W I N D O W S & F O R M A T T I N G P a g e | 21
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
This interface is command-driven and table below listed some of user command that
can be used to navigate files and folders in Windows directories and perform some
basic Windows operations.
Table 5.1 List of MS-DOS user commands
5.4. Interfacing with MS-DOS
Typing a commandIn general MS-DOS commands have three parts:
KEYWORD PARAMETER SWITCH
Keyword – A unique word or set of characters that identifies the action to be
performed. Some are quite descriptive: FORMAT, COPY, MOVE and others are
abbreviated: DEL, DEFRAG, MKDIR.
Parameter – Additional directions for the command.It may specify a directory or file on
which to perform the action.
Switches – A special type of parameter that enables or disables optional functions of
the command.
Optional
W I N D O W S & F O R M A T T I N G P a g e | 21
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
This interface is command-driven and table below listed some of user command that
can be used to navigate files and folders in Windows directories and perform some
basic Windows operations.
Table 5.1 List of MS-DOS user commands
5.4. Interfacing with MS-DOS
Typing a commandIn general MS-DOS commands have three parts:
KEYWORD PARAMETER SWITCH
Keyword – A unique word or set of characters that identifies the action to be
performed. Some are quite descriptive: FORMAT, COPY, MOVE and others are
abbreviated: DEL, DEFRAG, MKDIR.
Parameter – Additional directions for the command.It may specify a directory or file on
which to perform the action.
Switches – A special type of parameter that enables or disables optional functions of
the command.
Optional
W I N D O W S & F O R M A T T I N G P a g e | 21
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
This interface is command-driven and table below listed some of user command that
can be used to navigate files and folders in Windows directories and perform some
basic Windows operations.
Table 5.1 List of MS-DOS user commands
5.4. Interfacing with MS-DOS
Typing a commandIn general MS-DOS commands have three parts:
KEYWORD PARAMETER SWITCH
Keyword – A unique word or set of characters that identifies the action to be
performed. Some are quite descriptive: FORMAT, COPY, MOVE and others are
abbreviated: DEL, DEFRAG, MKDIR.
Parameter – Additional directions for the command.It may specify a directory or file on
which to perform the action.
Switches – A special type of parameter that enables or disables optional functions of
the command.
Optional
W I N D O W S & F O R M A T T I N G P a g e | 22
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
5.4.1. Getting HelpIf you are stuck or cannot remember MS-DOS command or format you can always
use a built-in library to help you. Type HELP followed by the command you want to
know about or type the command and then follow it with the switch /? to get detail
description of the command. You can also obtain a full list of DOS commands by
typing HELP in your DOS.
5.4.2. Viewing the contents of a directoryThe dir command lists the contents of a directory. Try typing dir in DOS.
You should get something like this:
5.4.3. Changing directoriesAll the names that have <DIR> beside to them are subdirectories. Try the following,
substituting WINDOWS for another directory name if it isn't present.
Note that the command prompt changes to display the current directory. Use the dir
command to list the files in the WINDOWS directory. To change back to the root
directory, use
to go up only one directory level, use
Changing drivesSo far you've been working on the hard drive (C:). Place a floppy disk in the A:
drive. And type:
a:
cd..
cd\
cd windows
Volume in drive C is MyHardDriveVolume Serial Number is 10CA-D5B9
Directory of C:\
28-Jul-03 08:45pm 0 AUTOEXEC.BAT28-Jul-03 08:45pm 0 CONFIG.SYS09-Feb-04 10:17pm <DIR> Documents and Settings27-Feb-04 01:39am <DIR> Program Files21-Feb-04 10:22pm <DIR> Temp28-Feb-04 06:48am <DIR> WINDOWS
2 File(s) 1,345 bytes4 Dir(s) 6,710,915,072 bytes free
W I N D O W S & F O R M A T T I N G P a g e | 23
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
This will change to the A: drive. Use dir to see if there is anything on the floppy
disk. Type:
Typing c: will change back to the C: drive — note that DOS remembers the current
directory on the disk.
5.4.4. Creating text filesWe can use the edit program to create and edit text files. Try:
Type a message into the text editor. When you have finished, use ALT-F on the
keyboard to bring up the file menu, then X to exit.
5.4.5. Copying filesThe copy command has two parameters: source and destination.
If the destination does not specify a filename then the same name is used.
The above command will copy the file into the parent fruit directory.
5.4.6. Renaming filesThe ren or RENAME command allows us to rename files.
5.4.7. Deleting filesThe del command allows us to delete files.
5.4.8. Formatting disksThe format command allows you to format a disk, preparing it for use for storing
files.
format a:
dirdel herstuff.txtdirdel myth*.txtdir
ren mystuff.txt herstuff.txt
copy myfile.txt \fruit
copy myfile.txt myfile.bak
edit myfile.txt
c:
W I N D O W S & F O R M A T T I N G P a g e | 24
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
LAB EXERCISE 1: MS-DOS Navigating
ATTENTION: EXERCISES MUST BE COMPLETED USING MS-DOS ONLY
Part 1
1) Create a text file called test.txt containing the text:
2) Save test.txt in directory C:\
3) Create a new folder named Original inside directory C:\
4) Rename test.txt as original.txt
Part 2
Continuing from Part 1, do the following:
1) Inside folder Original you just created, create a subdirectory called Garbage
2) Copy test.txt into garbage, naming the copy as file000.txt
3) Create three more copies of the same file in Garbage, called file001.txt to file003.txt
4) Go back to the root directory and create a new folder called Storage.
5) Copy all four files from Garbage to Storage.
Part 3
Delete the content of Garbage folder. This isn't as easy as it seems.
Write down all your command line (from Part 1, Part 2 and Part 3) in the box below:
There was a technician called AlifWho was fired by his bad-tempered bossHe got the old bootWhen he went to the rootAnd typed DEL *.* into DOS
W I N D O W S & F O R M A T T I N G P a g e | 25
Copyright of School of Electrical System Engineering, UniMAP | 2013 ©
LAB ASSIGNMENT : ANSWER ALL QUESTIONSNO QUESTION ANSWERWindows Formatting & Installation
1 List four major functions of an OS.
2 What are two file systems used by harddrives?
3 Which operating system is only used on AppleMacintosh computers
4 What is the latest Microsoft operating systemfor desktop computers?
5 Which operating system often used for serverapplications is a scaled-down version of Unix?
6 List all of the device types shown in DeviceManager.
7 What is the difference between a hard/coldboot and a soft/warm boot?
8 If a PC boots first to the hard drive beforechecking the floppy disk for an OS, how doyou change this boot sequence so that it firstlooks on the floppy disk for an OS?
9 List four ways to launch an application fromthe Windows desktop.
10 What is the command for creating directoryusing MS-DOS?
FINAL SCORE: ______________ %
Authorized Signature: ___________________ Date: ______________
_