12/08/03 1
September 12, 2005 1
Analysis of CC2 Rigid Pavement Test Data From the Analysis of CC2 Rigid Pavement Test Data From the FAA's National Airport Pavement Test FacilityFAA's National Airport Pavement Test Facility
David R. Brill, Ph.D.FAA Airport Technology R&D Branch, ATO-P (AJP -6310)William J. Hughes Technical Center, Atlantic City, NJ, USA
ICAO/ALACPA/FAA/ACI-LAC Seminar on Airfield Pavement DesignBogotá, Colombia
September 12, 2005
September 12, 2005 2 AAR-410
FAA Airport Technology R&D FAA Airport Technology R&D ProgramProgram
uEffort conducted at the William J. Hughes Technical Center, Atlantic City, NJ, USA.
uSponsor: FAA Office of Airport Safety and Standards, Washington, DC.
uProvide support for development of FAA pavement standards (Advisory Circulars).
u http://www.airporttech.tc.faa.gov/
September 12, 2005 3 AAR-410
National Airport Pavement National Airport Pavement Test Facility Test Facility -- BackgroundBackground
uCommissioned on April 12, 1999.u Joint venture of FAA and Boeing Co.uPrimary Objectives:uProvide additional traffic data for incorporation
in new FAA thickness design procedures.uProvide full-scale pavement response and
failure information for use in airplane landing gear design and configuration studies.
uReexamine the CBR method of design for flexible pavement ACN (6-wheel gear).
September 12, 2005 4 AAR-410
National Airport Pavement National Airport Pavement Test Facility Test Facility -- SpecificationsSpecifications
u Test pavement: 900 ft long by 60 ft wide.u Test vehicle: Up to 12 aircraft tires at wheel loads
up to 75,000 lbs.u Dynamic data acquisition (20 samples/second).u Static data acquisition (4 samples/hour).
September 12, 2005 5 AAR-410
Construction CyclesConstruction Cycles
u CC1: Initial construction, consisted of 6 flexible and 3 rigid test items.
u CC2: Rigid pavement reconstructionu Test strip and free standing test slabu Three new rigid test items
u CC3: Flexible pavement reconstruction.u Four conventional flexible test items.
A construction cycle is defined as the complete cycle of planning, construction, trafficking, posttraffic testing, and demolition, needed to obtain a set of usable data.
September 12, 2005 6 AAR-410
CC2 CC2 -- Objectives of TestObjectives of Test
u Main Objectives:u Compare rigid pavement life and performance for
different support conditions.u Compare pavement life and performance for 4 - and 6 -
wheel gear traffic.u Obtain data on pavement performance as measured by
the Structural Condition Index (SCI) versus traffic repetitions.
u Other objectives included comparing interior and edge stresses under gear loads, and measuring shrinkage and curling of the concrete slabs.
12/08/03 2
September 12, 2005 7 AAR-410
CC2 Test Item LayoutCC2 Test Item Layout
CENTERLINE
22.9 m (75 ft)
18.3
m (
60 ft
)
22.9 m (75 ft)22.9 m (75 ft)
MRC MRG MRSNorth CarriageTrafficked Area
South CarriageTrafficked Area
Direction ofTraffic
7.6 m (25 ft) TransitionArea (Typ.)
u MRC: Medium-Strength / Rigid / Conventional (aggregate) foundationu MRG: Medium-Strength / Rigid / Slab placed directly on Gradeu MRS: Medium-Strength / Rigid / Stabilized base (econocrete)
September 12, 2005 8 AAR-410
Detail Plan of PCC Test ItemDetail Plan of PCC Test Item
22.86 m (75 ft)
18.2
9 m
(60
ft)
SHOULDER
SHOULDER
TR
AN
SIT
ION
TR
AN
SIT
ION4.57 x 4.57 m (15 x 15 ft)
SLABS, TYP.
September 12, 2005 9 AAR-410
~1.2 m (4 ft) of Rebuilt SubgradeCBR 7-8
total subgrade depth of 2.7 m (9 ft)
15.2 cm (6 in)P-306 econocrete
43.2 cm (17 in)PCC
43.2 cm (17 in)PCC
25.4 cm (10 in) P-154 subbase
30.5 cm (12 in)Concrete
30.5 cm (12 in)Concrete
30.5 cm (12 in)Concrete
T5 T6MRC
21.9 cm (8-5/8 in)P-154 subbase
MRG MRS
Profile of CC2 Test ItemsProfile of CC2 Test Items
September 12, 2005 10 AAR-410
Structural Design Data for Structural Design Data for CC2 Test ItemsCC2 Test Items
Test Item MRC MRG MRS
PCC Surface 30.5 cm (12 in.)PCC(P-501)
30.5 cm (12 in.)PCC(P-501)
30.5 cm (12 in.)PCC(P-501)
Subbase 1 25.4 cm (10 in.)aggreg. subbase(P-154)
none 15.2 cm (6 in.)econocrete base(P-306)
Subbase 2 none none 21.9 cm (8.6 in.)aggregate subbase(P-154)
Subgrade Clay (CH)k=35.3 MPa/m(130 pci)
Clay (CH)k=38.0 MPa/m(140 pci)
Clay (CH)k=38.0 MPa/m(140 pci)
September 12, 2005 11 AAR-410
Gear Load Dimensions for CC2 Gear Load Dimensions for CC2 Traffic TestsTraffic Tests
137.
2 cm
(54
in.)
144.8 cm(57 in.)
144.8 cm(57 in.) 13
7.2
cm(5
4 in
.)
144.8 cm(57 in.)
(a) 6-wheel gear. (b) 4-wheel gear.
September 12, 2005 12 AAR-410
Traffic Summary for CC2 Test ItemsTraffic Summary for CC2 Test Items
Passes CompletedTest Item
GearType Apr-Jun 2004 Jul-Sep 2004 Oct-Dec 2004 Total
MRC-North 4-wheel 12675 0 0 12675
MRC-South 4-wheel 5405 0 0 5405
MRG-North 6-wheel 0 21186 9834 31020
MRG-South 4-wheel 0 21162 9834 30996
MRS-North 6-wheel 0 20262 0 20262
MRS-South 4-wheel 0 21162 9834 30996
12/08/03 3
September 12, 2005 13 AAR-410
Performance MonitoringPerformance Monitoring
u Visual Distress Surveys.u ASTM D 5340-93 and FAA AC 150/5380 -6. u Daily up to 10,000 passes. Weekly after 10,000 passes.
u Embedded Sensors.u Responses monitored for early indication of cracking.
u Nondestructive Tests. u HWD every 15 wanders (990 passes) up to 10,000
passes. Every 30 wanders after 10,000 passes.
u Destructive Testing. u Cores to investigate origin of cracks.
September 12, 2005 14 AAR-410
Final Distress MapsFinal Distress Maps
MRC MRG MRS
September 12, 2005 15 AAR-410
Structural Condition Index (SCI)Structural Condition Index (SCI)
u Rollings (1988).u SCI is structural component of rigid PCI.u Only load related distress types are considered (e.g.,
L/T/D cracks, corner breaks, shattered slab).u SCI is always equal to or higher than PCI for the same
pavement feature.u Joint and corner spalling was excluded from the SCI
computation for CC2 test items.
u SCI definition is not the same as “Structural PCI” as adopted by the U.S. Navy (MicroPAVER).
September 12, 2005 16 AAR-410
Micro PAVER ComputationsMicro PAVER Computations
u Record structural distresses based on visual surveys.
u Treat each test item (north side or south side) as a sample unit.
u Follow ASTM procedures for counting distresses and assigning severity levels.
September 12, 2005 17 AAR-410
SCI Versus Coverage AnalysisSCI Versus Coverage Analysis
u Plot SCI as a function of applied coverages.u P/C ratio is computed from wander pattern.
u All slabs in sample unit versus inside traffic lane only.
u Obtain linear regression of SCI versus log(C).u Intercept with SCI=100 line yields CO (cov. to 1st crack).u Intercept with SCI=0 line yields CF (cov. to full failure).
u New rigid design concerned with coverages to SCI=80.u Lower portions of failure curve (below SCI = 80) are
important for overlay designs.
September 12, 2005 18 AAR-410
Plot of SCI vs. Log of Plot of SCI vs. Log of CoveragesCoverages for for all CC2 Test Items With all CC2 Test Items With TrendlinesTrendlines
0
20
40
60
80
100
100 1000 10000
Coverages
SC
I
MRC-North MRC-South MRS-North MRS-South
MRG-North MRG-South CC2 Test Strip
CC2 Test Strip
MRC-South
MRC-North
MRS-North
MRG-North
MRG-South
MRS-South
12/08/03 4
September 12, 2005 19 AAR-410
Regression Data for Analysis Regression Data for Analysis of SCI Versus of SCI Versus CoveragesCoverages
Regression Constants*
Test Item A B R2
Coverages toInitial Crack,CO
Coverages toFull Failure,CF P/C
MRC-N -167.43 572.15 0.821 661 2613 3.80MRC-S -148.36 506.04 0.827 546 2576 4.71MRG-N -247.03 941.57 0.964 2551 6480 4.71MRG-S -246.96 935.12 0.965 2408 6117 4.71MRS-N -101.71 374.94 0.896 505 4855 4.71MRS-S -231.66 871.57 0.961 2141 5784 4.71Test Strip -90.33 296.37 0.904 149 1910 4.13
( ) BCA += logSCI*
September 12, 2005 20 AAR-410
Distress Modes in CC2 Test Distress Modes in CC2 Test ItemsItems
u Measured uplift at all corners was kept minimal (0.38 mm / 15 mils or less).
u Top-down cracks were not eliminated in either the outside or inside lanes.u Inside lanes: Received traffic from both wheels. Both top-
down and bottom-up fatigue cracks were observed.u Outside lanes: Received either no traffic (MRC) or traffic
from only one wheel of the dual gear. Top-down cracks were observed.
u Top-down cracks appeared first on outside slabs, even though those slabs received relatively less traffic.
September 12, 2005 21 AAR-410
Fatigue Cracks Observed in Fatigue Cracks Observed in CC2 Test ItemsCC2 Test Items
Core Sample Showing a Bottom-up Crack in Test Item MRS-South
September 12, 2005 22 AAR-410
Fatigue Cracks Observed in Fatigue Cracks Observed in CC2 Test ItemsCC2 Test Items
Top-down crack observed in outside lane of test item MRC-North (Slab S-2)
September 12, 2005 23 AAR-410
SCI EvaluationSCI Evaluation
u To avoid distortion of the SCI-vs.-coverage analysis due to the early appearance of top-down cracks in the outside lanes, only those slabs receiving traffic from bothtires of the dual gear (i.e., the 5 inside slabs) were included in the SCI sample units.
u For SCI evaluation, no distinction was made between visible top-down and bottom-up cracks.
September 12, 2005 24 AAR-410
Results: Stabilized and Results: Stabilized and NonstabilizedNonstabilized Test ItemsTest Items
u Deterioration of SCI is best represented by a model that is linear in log of coverages, regardless of whether a stabilized base is used.
u In general, CC2 test results support the principle that higher-quality subbases extend pavement life.u Additional durability is reflected in the slope of SCI-
vs.-log(C) trendline. In general, stabilized base structures exhibited the flattest slope, followed by conventional, and (lastly) slab -on-grade structures.
u Exception was MRS-S.
12/08/03 5
September 12, 2005 25 AAR-410
0
20
40
60
80
100
120
1 10 100 1000 10000 100000
Coverages
SCI
MRS-North (6 wheel, P/C = 4.71) MRS-South (4 wheel, P/C = 4.71)Exist. Failure Model - 6 wheel (No Compensation) Exist. Failure Model - 4 wheel (No Compensation)
Exist. Failure Model - 6 wheel (SB compensation) Exist. Failure Model - 4 wheel (SB Compensation)Log. (MRS-North (6 wheel, P/C = 4.71)) Log. (MRS-South (4 wheel, P/C = 4.71))
SCI vs. Coverage Curves for Stabilized SCI vs. Coverage Curves for Stabilized Base Test ItemsBase Test Items
LEDFAA Failure Model -Includes Stabilized Base
Compensation
September 12, 2005 26 AAR-410
Design Factor vs. Design Factor vs. CoveragesCoverages
u Design Factor (DF) = ratio of concrete flexural strength to maximum calculated bending stress.
u LEDFAA model based on Rollings (1988) regression:u DF = 0.5234 + 0.3920 log (CO) coverages to onset of crackingu DF = 0.2967 + 0.3881 log (CF) coverages to full failure (SCI 0)
u Recompute design factors for all test items using FEDFAA (3D-FEM) edge stress.
u Evaluate parameters including 7 new NAPTF data points.
u Preliminary analysis - design factors subject to change as we continue to characterize the material properties.
September 12, 2005 27 AAR-410
ConclusionsConclusions
u Rigid pavement full-scale traffic tests recently completed at the FAA's National Airport Pavement Test Facility provided pavement performance and failure data for three new rigid pavement test items and a test strip.
u The performance data were analyzed using the SCI concept to obtain coverages to initiation of structural cracking and to full structural failure.
u The test results are currently being analyzed in conjunction with previous full-scale tests and will be used to update the failure model for rigid pavement and overlay design in future FAA design software.
September 12, 2005 28 AAR-410
Questions?Questions?