Download - ERSU Guida (test)
-
8/9/2019 ERSU Guida (test)
1/55
Thank you for purchasing this projector.
The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. The reproduction, transmission or use of this document or contents is not permitted withoutexpress written authority.
TRADEMARK ACKNOWLEDGMENT : VGA and XGA are registered trademarks of the International Business Machines Corporation. Apple and Mac are registered trademarks of Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard Association. Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
NOTE
WARNING Before using, read the "User's Manual - Safety Guide" andthese manuals to ensure correct usage through understanding. After reading,
store them in a safe place for future reference.
Projector
CP-S210/CP-S210T/CP-S210FCP-S210W/CP-S210WT/CP-S210WF
User's Manual - Operating Guide
1www.touchboards.com 205 Westwood Ave.Long Branch, NJ 077401-866-942-6273 [email protected]
ww.touchboards.com 205 Westwood Ave.Long Branch, NJ 07740 1-866-942-6273 [email protected]
-
8/9/2019 ERSU Guida (test)
2/55
Projector Features 3Preparation 3Part Names 4
The Projector
4Fastening The Lens Cap 4The Remote Control 6
Setting Up 7Arrangement 7Adjusting The ProjectorsElevator 8Connecting Your Devices 9Connecting Power Supply 11
Remote Control 12Putting Batteries 12Operating The Remote Control 13
Power ON/OFF 14Turning On The Power 14Selecting An Input Signal 15Turning Off The Power 16
Operating 17
Adjusting The Volume 17Temporarily Muting The Sound 17Adjusting The Position 18Using The AutomaticAdjustment Feature 19Correcting KeystoneDistortions 19Using The Magnify Feature 20Freezing The Screen 20Signal Searching 21Selecting The Aspect Ratio 21Temporarily BlankingThe Screen 21
Multifunctional Settings 22Using The Menu Functions 22MAIN Menu 23
PICTURE-1 Menu
24PICTURE-2 Menu 26INPUT Menu 27AUTO Menu 29SCREEN Menu 30OPTION Menu 31
Lamp 32Replacing The Lamp 33
Air Filter 34Caring For The Air Filter 34Replacing The Air Filter 35
Other Care 36Caring For The InsideOf The Projector 36Caring For The Lens 36Caring For The CabinetAnd Remote Control 36
Troubleshooting 37Related Messages 37RegardingThe Indicator Lamps 39Phenomena That May Easily BeMistaken For Machine Defects 41Warranty And After-Service 42
Specifications 43
Contents
2
-
8/9/2019 ERSU Guida (test)
3/553
G Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highlyefficient optical system.
G Whisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation.
G User Memory Function This projector can memorize 4 settings by MY MEMORY function.
G Partial Magnification Function Interesting parts of images can be magnified for closer viewing.
G Keystone Distortion Correction Quick correction of distorted images electrically.
PreparationPlease see the Contents Of Package of the Users Manual Quick Guide.Your projector should come with the items shown there. Contact your dealeranything is missing.
Projector FeaturesThis multimedia projector is used to project various computer signals as well asNTSC / PAL / SECAM video signals onto a screen. Little space is required forinstallation and large images can easily be realized.
Keep the original packing material for future reshipment.NOTE
-
8/9/2019 ERSU Guida (test)
4/554
Strap Rivet
Straphole
Part Names
The Projector
Zoom ring 15
Focus ring 15 Air filter cover(An air filter isinside.)
34
Elevator button8
Elevator feet8
Indicates the correspondingreference page
Lens cap 14
Lens(The picture isprojected from
here.)
Remote sensor13
Projector (Front/Right)
Fastening The Lens Cap
To avoid losing, please fasten the lens cap to the projector using the strap.
1 Fix the strap to the strap ring of lenscap, as the right drawing.
2 Put one piece of the strap into thegroove on rivet, as the right drawing.
3 Push the rivet into the strap hole.
Lens cap Strap ring Strap
Pull
Rivet
Push in(Bottom side)
-
8/9/2019 ERSU Guida (test)
5/555
AC inlet11
VIDEO port 10
AUDIO port(from a computer)
10
S-VIDEO port 10
COMPONENT VIDEO - Y 10
COMPONENT VIDEO - C B /P B 10
COMPONENT VIDEO - C R /P R 10
AUDIO R portL port
(from a video equipment)
10
10
Power switch14
RGB port10
CONTROLport
10
Projector (Rear/Left)
STANDBY/ONINPUT
POWER LAMPTEMP
MENU
POWER indicatortells the state of powersupply. Refer to the sectionPower ON/OFF .
INPUT buttontoggles between the signalports.
MENU buttonsoperate the menu function.
STANDBY/ON
buttonprepares for turning thepower on/off. Refer to thesection Power ON/OFF .
TEMP indicatorlights or blinks when anyproblem about internaltemperature has happened.
LAMP indicatorlights or blinks when anyproblem about the lamp has
happened.
RGB VIDEO
S-VIDEO
COMPONENT VIDEO
A C IN
Part Names (continued)
The Projector (continued)
15 14 39
39
22
14
-
8/9/2019 ERSU Guida (test)
6/556
The Remote Control
(STANDBY/ON)button
prepares for turning thepower on/off.
VIDEO buttontoggles between the signalports of VIDEO, S-VIDEOand COMPONENT VIDEO.
MENU buttonopens/closes the menu.
RGB buttonselects the input signal of
RGB port.
BLANK buttonblanks the screentemporarily.
SEARCH buttonsearches for an input
signal between thefollowing signal ports ofRGB, VIDEO, S-VIDEOand COMPONENT VIDEO.
VOLUME buttonturns on/off the VOLUMEmode.In the VOLUME mode,To adjust the volume,use the cursor /buttons.
MUTE button
mutes/restores the sound.
KEYSTONEbutton
turns on/off the KEYSTONEmode.In the KEYSTONE mode,To adjust thekeystone,use the cursor /buttons.
ASPECT buttontoggles between themodes for aspect ratio.
AUTO buttonexecutes automaticadjustment.
MAGNIFY ON/OFFbuttonsturns on/off the MAGNIFYmode.In the MAGNIFY mode,To move themagnified area,(1) Press the POSITIONbutton.(2) Use the cursor buttonsto move the picture.(3) Press the POSITIONbutton again to finish.To shift the magnifylevel,use the cursor /buttons.
FREEZE buttonfreezes/reactivates thepicture.
POSITION buttonturns on/off the POSITIONmode. (for RGB input)In the POSITION mode,To move the picture,use the cursor buttons.
ESC buttonreturns to the previousdisplay at the menufunctions.
, , ,(Cursor) buttons
works for adjusting ormenu controlling.
RESET buttoncancels the adjustment inprogress.* The adjustments of the
volume etc. are not reset.
ENTER buttonproceeds to the nextoperation at the menufunctions.
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLANK
RGB SEARCH
OFF
ON
Part Names (continued)
15
15
21
20
20
18
2222
22 22
22
19
17
17
21
19
1421
-
8/9/2019 ERSU Guida (test)
7/557
Setting Up
Arrangement
WARNING Install the projector in a suitable environment according toinstructions of the User s Manual Safety Guide and this manual. The power outlet should be close to the projector and easily accessible.
Refer to the illustrations and tables below to determine the screen size and projectiondistance.The values shown in the table are calculated for a full size screen:800 600(a):Distance from the projector to the screen (10%)(b):Distance from the lens center to the bottom of the screen (10%)(c):Distance from the lens center to the top of the screen (10%)
Screen Size [inch (m)] (a) [inch (m)] (b)
[inch (cm)]
(c)
[inch (cm)]Min. Max.30 (0.8) 35(0.9) 42(1.1) 2(5) 16(41)
40 (1.0) 47(1.2) 56(1.4) 2(6) 22(55)
50 (1.3) 59(1.5) 71(1.8) 3(8) 27(69)
60 (1.5) 71(1.8) 85(2.2) 4(9) 32(82)
70 (1.8) 83(2.1) 99(2.5) 4(11) 38(96)
80 (2.0) 95(2.4) 114(2.9) 5(12) 43(110)
90 (2.3) 107(2.7) 128(3.3) 5(14) 49(123)
100 (2.5) 119(3.0) 143(3.6) 6(15) 54(137)
120 (3.0) 143(3.6) 171(4.4) 7(18) 65(165)
150 (3.8) 179(4.6) 215(5.5) 9(23) 81(206)
200 (5.0) 240(6.1) 287(7.3) 12(30) 108(274)
250 (6.3) 300(7.6) 359(9.1) 15(38) 135(343)
300 (7.5) 360(9.2) 431(10.9) 18(46) 162(411)
(a)
(c)
(b)
Lens center
Screen
Reference forthe 4:3 aspect ratio
Screen Size [inch (m)] (a) [inch (m)] (b)[inch (cm)](c)
[inch (cm)]Min. Max.30 (0.8) 38(1.0) 46(1.2) 0(1) 15(39)
40 (1.0) 51(1.3) 61(1.6) 1(2) 20(51)
50 (1.3) 64(1.6) 77(2.0) 1(2) 25(64)60 (1.5) 77(2.0) 93(2.4) 1(2) 30(77)
70 (1.8) 90(2.3) 108(2.8) 1(3) 35(90)
80 (2.0) 104(2.6) 124(3.2) 1(3) 41(103)
90 (2.3) 117(3.0) 140(3.6) 1(4) 46(116)
100 (2.5) 130(3.3) 155(3.9) 2(4) 51(129)
120 (3.0) 156(4.0) 187(4.7) 2(5) 61(154)
150 (3.8) 196(5.0) 234(5.9) 2(6) 76(193)
200 (5.0) 216(6.6) 312(7.9) 3(8) 101(257)
250 (6.3) 327(8.3) 391(9.9) 4(10) 127(322)
300 (7.5) 393(10.0) 469(11.9) 5(12) 152(386)
(a)
(c)
(b)
Lens center
Screen
Reference forthe 16:9 aspect ratio
Side View
Side View
-
8/9/2019 ERSU Guida (test)
8/558
Adjusting The Projector's Elevator
CAUTION If you press the elevator buttons without holding the projector, theprojector might crash down, overturn, smash your fingers and possibly result inmalfunction. To prevent damaging the projector and injuring yourself, ALWAYS HOLDTHE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
You can use the elevator feet to make adjustments if the surface on which you need to setthe projector is uneven or if you otherwise need to adjust the angle of projection. Theadjustment range of the elevator feet is 0 to 9 degrees.
1 Press and hold in the elevator buttons.
2 Raise or lower the projector to thedesired height and then release theelevator buttons.When you release the elevator buttons, the elevatorfeet will lock into position.
3As necessary, you can also finelyadjust the height of the projector bytwisting the elevator feet by hand.
Elevator buttons
Elevator feet
Setting Up (continued)
-
8/9/2019 ERSU Guida (test)
9/559
Connecting Your Devices
WARNING Incorrect connecting could result in fire or electrical shock.Whenever attempting to connect other devices to the projector, please thoroughly readthe "User's Manual - Safety Guide", this manual and the manual of each device to beconnected.
CAUTION TURN OFF ALL DEVICES prior to connecting them to the projector.Attempting to connect a live device to the projector may generate extremely loudnoises or other abnormalities that may result in malfunction and/or damage to thedevice and/or projector.ATTENTION Make sure that you connect devices to the correct port. Incorrectconnection may result in malfunction and/or damage to the device and/or projector.Refer to the section TECHNICAL of this manual for the pin assignment of connectors
and RS-232C communication data. Some cables have to be used with core set. Use the accessory cable or adesignated-type cable for the connection. For cables that have a core only at one end,connect the core to the projector. Secure the screws on the connectors and tighten. Whenever attempting to connect a laptop computer to the projector, be sure toactivate the laptop s RGB external image output (set the laptop to CRT display or tosimultaneous LCD and CRT display). For details on how this is done, please refer to theinstruction manual of the corresponding laptop computer.
About Plug-and-Play Capability This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved byconnecting this projector to computers that are VESA DDC (display data channel)compatible. Please take advantage of this function by connecting the accessory RGBcable to the RGB port (DDC 1/2B compatible). Plug-and-Play may not work properly ifany other type of connection is attempted. Plug-and-Play is a system composed of the computer, its operating system andperipheral equipment (i.e. display devices).
Please use the standard drivers in your computer as this projector is a Plug-and-Playmonitor.
NOTE
Some computers may have multiple display screen modes. Use of some ofthese modes will not be possible with this projector. For some RGB input modes, the optional Mac adapter is necessary. When the image resolution is changed on a computer, depending on an input,automatic adjust function may take some time and may not be completed. In this case,
you may not be able to see a check box to select Yes/No for the new resolution onWindows. Then the resolution will go back to the original. It might be recommended touse other CRT or TFT monitors to change the resolution.
NOTE
Setting Up (continued)
-
8/9/2019 ERSU Guida (test)
10/55
-
8/9/2019 ERSU Guida (test)
11/5511
1A C IN
Connect the connec tor of thepower cord to the AC inlet of theprojector. 1
2 Firmly plug the power cords pluginto the outlet.
WARNING Please use extra caution when connecting the power cord as
incorrect or faulty connections may result in FIRE and/or ELECTRICAL SHOCK. Pleaseadhere to the User s manual Safety Guide and the following. Only plug the power cord into outlets rated for use with the power cord s specifiedvoltage range. Only use the power cord that came with the projector. If it is damaged, contact yourdealer to newly get correct one. Never modify the power cord. Never attempt to defeat the ground connection of thethree-pronged plug. Make sure that you firmly connect the power cord to the projector and wall outlet.
AC Inlet Connector Side1
Connecting Power Supply
Setting Up (continued)
-
8/9/2019 ERSU Guida (test)
12/5512
CAUTION Always handle the batteries with care and use them only as directed.
Improper use may result in battery cracking or leakage, which could result in fire, injuryand/or pollution of the surrounding environment. Keep the battery away from children and pets. Be sure to use only the batteries specified for use with the remote control. Do not mixnew batteries with used ones. When inserting batteries, verify that the plus and minus terminals are aligned correctly(as indicated in the remote control). When you dispose the battery, you should obey the law in the relative area or country.
1 Remove thebattery cover.Slide back andremove the batterycover in the directionof the arrow.
Insert thebatteries.Align and insert the twoAA batteries according totheir plus and minusterminals (as indicated inthe remote control).
Close thebattery cover.Replace the batterycover in the directionof the arrow andsnap it back intoplace.
2 3
Remote Control
Putting Batteries
-
8/9/2019 ERSU Guida (test)
13/5513
Operating The Remote Control
ATTENTION Do not drop or otherwise expose the remote control to physical
impact. Do not get the remote control wet or place it on wet objects. Doing so may result inmalfunction. Remove the batteries from the remote control and store them in a safe place if youwon t be using the remote control for an extended period. Replace the batteries whenever the remote control starts to malfunction. When strong lights, such as direct sunlight or light from an extremely close range(such as from an inverter fluorescent lamp), hit the projector s remote sensor, theremote control may cause to function. Adjust the direction of the projector to keep lightfrom directly hitting the projector s remote sensor.
The remote control works with the projector s remotesensor.
The range of the remote sensor is 3 meters with a 60-degree range (30 degrees to the left and right of theremote sensor).Also a remote signal reflected in the screen etc. may beavailable. If it is difficult to send a remote signal to thesensor directly, please try.
Since the remote control uses infrared light to sendsignals to the projector (Class1 LED), be sure to use theremote control in an area free from obstacles that couldblock the remote control s output signal to the projector.
30 30
approximately3 meters
Remote sensor
Remote Control (continued)
-
8/9/2019 ERSU Guida (test)
14/5514
STANDBY/ONINPUT
POWER LAMPTEMP
MENU
Power ON/OFF
Turning On The Power
WARNING When the power is ON, a strong light is emitted. Do not look into thelens or vents of the projector.
Turn the power on/off in right order. Please power on the projector beforethe connected devices. Power off the projector after the connected devices.
NOTE
1 Make sure that the power cord isfirmly and correctly connected to theprojector and outlet.
2 When the lens cap is attached, removethe lens cap.
3 Set the power switch to [ | ] (ON).
4 Press the STANDBY/ON button of theprojector or the button of the remotecontrol.The projector lamp will light up and the POWERindicator will begin blinking green.According to a setup, the projector lamp may lightup and the POWER indicator may begin blinkinggreen, without pressing this button.
When the power is completely on, the indicator willstop blinking and light green.
The POWER indicator will light orange.
Power switch (ON position)
AC IN
Power switch
STANDBY/ON button
POWER indicator
VIDEO
ASPECT
VOLUMEMAGNIFY
AU TO B LA NK
R GB S EA RCH
ON
(STANDBY/ON) button
-
8/9/2019 ERSU Guida (test)
15/5515
VIDEO
ASPECT
VOLUMEMAGNIFY
AU TO B LA NK
R GB S EA RC H
ON
VIDEO
ASPECT
VOLUMEMAGNIFY
AU TO B LA NK
R GB S EA RC H
ON
Selecting An Input Signal
1
2 Use the zoom ring to adjust the screensize.
3 Use the focus ring to focus the picture.
Press the INPUT button.As illustrated below, each time you press the INPUTbutton, the projector switches between its input signalports. Select the signal you wish to project.
Using the projectors control button
Press the RGB button.When this button is pressed, the projector switches tothe RGB port.
Selecting a RGB signal, using the remote control
Press the VIDEO button.As illustrated below, each time you press the VIDEObutton, the projector switches between its input signalports. Select the signal you wish to project.
Selecting a video signal, using the remote control
RGB VIDEO S-VIDEO
COMPONENT VIDEO
VIDEO S-VIDEO
COMPONENT VIDEO
AC IN
STANDBY/ONINPUT
POWER LAMPTEMP
MENU
INPUT button
RGB button
VIDEO button
Zoom ringFocus ring
Power ON/OFF (continued)
-
8/9/2019 ERSU Guida (test)
16/5516
Turning Off The Power
Turn the power on/off in right order. Please power on the projector before
the connected devices. Power off the projector after the connected devices.
NOTE
AC IN
Power switch
STANDBY/ONINPUT
POWER LAMPTEMP
MENU
STANDBY/ON button
POWER indicator
1 Press the STANDBY/ON button of theprojector or the button of the remotecontrol.The message Power off? will appear on the screenfor approximately 5 seconds.
4 Attached the lens cap.
2 Press the STANDBY/ON button againwhile Power off? the message isvisible.The projector lamp will go off, and the POWERindicator will begin blinking orange.Then the POWER indicator will stop blinking and lightto solid orange when the lamp cooling is complete.
3 Switch the power switch to [O] (OFF).
The POWER indicator will go off.
Power switch (OFF position)
Power ON/OFF (continued)
VIDEO
ASPECT
VOLUMEMAGNIFY
AU TO B LA NK
R GB S EA RCH
ON
(STANDBY/ON) button
-
8/9/2019 ERSU Guida (test)
17/5517
Operating
Adjusting The Volume
Temporarily Muting The Sound
1 Press the VOLUME button.As illustrated on the right, a dialog willappear on the screen to aid you in adjustingthe volume.
2 Use the / buttons to adjust thevolume.Press the VOLUME button again to close the dialog andcomplete this operation.(Even if you don't do anything, the dialog willautomatically disappear after a few seconds.)
Press this to increase the volumePress this to decrease the volume
16
VOLUME
16
VOLUME
VOLUMEOLUME
1 Press the MUTE button.Press the MUTE button.As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.(If you don't do anything, the dialog will automaticallydisappear after a few seconds.)Press the MUTE or VOLUME button to restore the sound.
VOLUME
16
MUTEUTE
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLANK
R GB SEAR CH
OFF
ON
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLANK
R GB SEAR CH
OFF
ON
-
8/9/2019 ERSU Guida (test)
18/5518
Adjusting The Position
1 Press the POSITION button.As illustrated on the right, a dialog will appear on the screento aid you in adjusting the position.
2 Use the , , , buttons to adjustthe position.When you want to initialize the position, press the RESETbutton during adjustment.Press the POSITION button again to close the dialog andcomplete this operation. (Even if you don't do anything, thedialog will automatically disappear after a few seconds.)This function is only available for RGB input.
POSITION
POSITION
When a menu is displayed, the operation of adjusting the position worksfor the position of not the picture but the menu.
NOTE
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLAN K
RGB SEARCH
OFF
ON
Operating (continued)
-
8/9/2019 ERSU Guida (test)
19/5519
Using The Automatic Adjustment Feature
Correcting Keystone Distortions
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLANK
R GB SEAR CH
OFF
ON
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLANK
OFF
ON
The automatic adjustment operation requires approximately 10 seconds.Also, please note that it may not function correctly with some input.
NOTE
1 Press the AUTO button.
Horizontal position (H POSITION), vertical position (V POSITION),clock phase (H PHASE) and horizontal size (H SIZE) areautomatically adjusted.Make sure that the application window is set to its maximum sizeprior to attempting to use this feature. Dark pictures may still beincorrectly adjusted. Use a bright screen when adjusting.
The signal type best suited for the respective input signal isselected automatically.This feature is available only if VIDEO is set to AUTO in the INPUTmenu.
Automatic Adjustment for RGB Input
Automatic Adjustment for Video Input
AUTO
1 Press the KEYSTONE button.As illustrated on the right, a dialog will appear onthe screen to aid you in correcting the distortion.
2 Use the , buttons to correct distortion.Press the KEYSTONE button again to close the dialogand complete this operation. (Even if you don't doanything, the dialog will automatically disappear aftera few seconds.)
KEYSTONE
+0
KEYSTONE
When the WIDE is selected under the ASPECT item of the MAIN menu, this
adjustment is ignored. The correcting keystone distortions function may not be work well with some types ofinput signals. The adjustable range for correcting keystone distortions will vary with the type ofinput signal.
NOTE
Operating (continued)
-
8/9/2019 ERSU Guida (test)
20/5520
Using The Magnify Feature
Freezing The Screen
1 Press the MAGNIFY (ON) button.The projector enters MAGNIFY mode.
2 Press the POSITION button, then use the, , , buttons to select the areato zoom. Press the POSITION button againto finalize the zoom area.
3 Use the , buttons to adjust the zoomlevel.Press the MAGNIFY (OFF) button to exit MAGNIFYmode and restore the screen to normal.(Theprojector will also automatically exit MAGNIFYmode if there is a change in the input signal'sstate.)
ON
MAGNIFYAGNIFY
POSITIONPOSITION
The projector will automatically exit from MAGNIFY mode if either theSEARCH, RGB, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in theinput signal's state. The correcting keystone condition may vary when the magnify function is active. Inthis case, please make the magnify OFF, so the correcting keystone condition will berestored.
NOTE
The freezing function will automatically finish if either the STANDBY/ON,SEARCH, RGB, VIDEO, BLANK, AUTO, VOLUME, MUTE, POSITION or MENU button of
remote control is pressed, or if a button of projector is pressed, or if there is a changein the input signal s state. If the projector continues projecting the same image for a long time (i.e. you forget toexit FREEZE mode), the image might possibly remain as an afterimage. Do not leavethe projector in FREEZE mode for too long.
NOTE
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLAN K
RGB SEARCH
OFF
ON
1 Press the FREEZE button.The [II] icon appears and the screen will freezeat the current image. Press the FREEZE buttonagain and the [ ] appears as the projector exits FREEZEmode.
MUTE
KEYSTONEFREEZE
MENUPOSITION
OFF
ON
FREEZE
Operating (continued)
-
8/9/2019 ERSU Guida (test)
21/5521
Signal Searching
Selecting The Aspect Ratio
1 Press the SEARCH button.Cycle through input signals, displaying the images of retrieved signals. Ifno signal is found, returns to the signal that was selected before the searchwas begun.
May not function properly with some input signals. The signal searching function takes about 10 seconds to display an image.
NOTE
The temporarily blanking function will automatically finish if either the STANDBY/ON, SEARCH,RGB, VIDEO, FREEZE, AUTO, VOLUME, MUTE, POSITION or MENU button of remote control is pressed, or ifa button of projector is pressed, or if there is a change in the input signal s state.
NOTE
RGB VIDEO S-VIDEO
COMPONENT VIDEO
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
VOLUMEMAGNIFY
AUTO BLAN K
RGB SEARCH
OFF
ON
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLAN K
RGB SEARCH
OFF
ON
VIDEO
ASPECT
VOLUMEMAGNIFY
AUTO BLAN K
RGB SEARCH
ON
SEARCH
1
At a COMPONENT VIDEO input of 16:9 Hi-Vision of 1125i(1035i/1080i)/750p, only 16:9 can be selected.
When the 4:3 is selected under the SCREEN TYPE item of the OPTION
menu. WIDE and ZOOM cannot be selected.
At a RGB input, selecting an aspect ratio may display the message
SYNC IS OUT OF RANGE
. In this case, please select one of otheraspect ratios.
ASPECTRGB input
VIDEO, S-VIDEO, COMPONENT VIDEO input
Press the ASPECT button.
4:3 16:9 15:9 32:15
4:3 16:9 WIDE ZOOM
Temporarily Blanking The Screen
1 Press the BLANK button.The input signal screen is shut off, and a blank screen appears. You canset the blank screen using the menu (from the SCREEN menu,select BLANK).Press the BLANK button again to remove the blank screen,and return to the input signal screen.
BLANK
Operating (continued)
-
8/9/2019 ERSU Guida (test)
22/5522
This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO,SCREEN, OPTION. Each of these menus is operated using the same methods. The basicoperations of these menus are as follows.
1 Press the MENUbutton.The menu displayappears on the screen.
2 Use the / buttons to selecta menu , thenpress the orENTER button.The display of theselected menuappears.
3 Use the / buttons to select an item,then press the or ENTER button.The operation display of the selected item appears.
4 Use the / buttons to operate the item.When you want to reset the adjustment, press the RESETbutton during the operation. Note that the items whosefunctions are performed simultaneously with operating (ex.LANGUAGE, WHISPER, H PHASE etc.) are not reset.When you want to return to the previous display, press the
or ESC button.
[ex. AdjustingVOLUME]1. Press the MENU
button.
2.Use the /buttons to select
the OPTION, thenpress the orENTER button.
3.Use the /buttons to selectthe VOLUME,then press the
or ENTERbutton.
4.Use the /buttons to adjustthe VOLUME.
5.Press the MENUbutton.5 Press the MENU button, or do not performany operation for several seconds .
The menu display disappears and your operation finishes.
MENU
RESETESC
ENTER
VIDEO
ASPECT
MUTE
KEYSTONEFREEZE
MENUPOSITION
ENTER
ESC RESET
VOLUMEMAGNIFY
AUTO BLAN K
RGB SEARC H
OFF
ON
Using The Menu Functions
Multifunctional Settings
-
8/9/2019 ERSU Guida (test)
23/5523
MAIN Menu With the MAIN menu, the items shown in the table below can beperformed.
Perform each operation in accordance with the instructions in thetable below.
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
KEYSTONEBRIGHTCONTRASTASPECTWHISPERMIRRORLANGUAGE[Language]
+0+0+04:3NORMALNORMALENGLISH
: SELECT
Item Description
KEYSTONE
Adjust the Keystone (Vertical) Distortion:Upper in the data Lower in the data
The adjustable range of this function will vary with the type of input signal. Atsome signals, this function may not work well.
When the V:INVERT or the H&V:INVERT is selected under the MIRROR item, ifthe projector screen is inclined or if the projector is angled downward, thisfunction may not work correctly.
When the WIDE is selected under the ASPECT item of the MAIN menu, thisadjustment is ignored.
When the zoom adjustment is set to the TELE side, this correction may beexcessive. This function should be used with zoom set to WIDE wheneverpossible.
BRIGHT Adjust Brightness: Light Dark
CONTRAST Adjust Contrast: Strong Weak
ASPECT
Select an Aspect RatioAt a RGB input:
4:3 16:9 15:9 32:15 At a RGB input, selecting an aspect ratio may display the message SYNC IS
OUT OF RANGE . In this case, please select one of other aspect ratios.At a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input:
4:3 16:9 WIDE ZOOM At a COMPONENT VIDEO input of 16:9 Hi-Vision of 1125i(1035i/1080i)/750p,
only 16:9 can be selected. When the 4:3 is selected under the SCREEN TYPE item of the OPTION menu,
WIDE and ZOOM cannot be selected.
WHISPER
Select the Whisper Mode:NORMAL WHISPER
When the WHISPER is selected, acoustic noise and screen brightness arereduced.
MIRROR Select a Mirror Status:NORMAL H:INVERT V:INVERT H&V:INVERT
LANGUAGE
Select a Menu Language:ENGLISH FRANAIS DEUTSCH ESPAOL ITALIANO NORSK NEDERLANDS PORTUGUS SVENSKA SUOMI POLSKI
RESET
Reset the MAIN Menu Items:Selecting the EXECUTE performs this function.EXECUTE CANCEL
The items of the MAIN menu are collectively returned to the initial setting.Note that the items WHISPER and LANGUAGE are not reset.
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
24/5524
PICTURE - 1 Menu With the PICTURE - 1 menu, the items shown in the Table below can beperformed.Perform each operation in accordance with the instructions in the table below.
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
GAMMACOLOR BAL RCOLOR BAL GCOLOR BAL BSHARPNESSCOLORTINTMY MEMORY
NORMAL+0+0+0+0+0+0SAVE1
: SELECT
Item Description
GAMMA
Select a Gamma Mode:NORMAL CINEMA DYNAMIC CUSTOM
Selecting the COSTOM and then pressing the or the ENTER button callsthe CUSTOM menu.
CUSTOM MenuSelecting one from the following and then pressing the or the ENTERbutton performs each function.
GAMMA COLOR TEMP R G B The R, G and B can be selected only when the USER is selected under the
COLOR TEMP.
COLOR BAL R Adjust the Red Color Balance: Strong Weak
COLOR BAL G Adjust the Green Color Balance: Strong WeakCOLOR BAL B Adjust the Blue Color Balance: Strong Weak
SHARPNESSAdjust the Whole Sharpness: Clear Soft This is a function for video inputs. This item can t be selected only at RGB
inputs.
COLOR
Adjust COLOR : Strong Weak This is a function for video inputs. This item can t be selected only at RGB
inputs including SCART RGB inputs. It is unavailable to deepen colors on SECAM signal input. (The adjustment
bar position and value in menu box are changeable but no effect.)
TINTAdjust the Tint: Green Red This is a function for video inputs. This item can t be selected only at RGB
inputs including SCART RGB inputs.
Multifunctional Settings (continued)
GAMMAAdjust the Gamma Data:
Up Down
COLOR TEMPSelect a Color Temperature Mode:
HIGH MIDDLE LOW USER
R
Adjust the Red Color Level for the USER mode of theCOLOR TEMP:
Strong Weak
G
Adjust the Green Color Level for the USER mode of theCOLOR TEMP:
Strong Weak
B
Adjust the Blue Color Level for the USER mode of theCOLOR TEMP:
Strong Weak
CUSTOM
CUSTOM
CUSTOM
CUSTOM
CUSTOM
-
8/9/2019 ERSU Guida (test)
25/5525
Item Description
MY MEMORY
Load/Save a Setting:
Selecting one from the following and then pressing the or the ENTERbutton performs each function.
LOAD1 LOAD2 LOAD3 LOAD4 SAVE1 SAVE2 SAVE3 SAVE4
This projector has 4 memories called M1, M2, M3 and M4 for settings.Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current setting dataon the memory whose number corresponds. Performing the LOAD1, LOAD2,LOAD3 or LOAD4 calls the data of memory whose number corresponds, andadjusts the picture automatically depending on the data.
The LOAD1, LOAD2, LOAD3 or LOAD4 cannot be selected when there is nomemory whose number corresponds.
At a different signal input from the signal that was being inputted when thesetting was memorized, the picture may not be adjusted correctly.
RESET
Reset the PICTURE-1 Menu Items:Selecting the EXECUTE performs this function.
EXECUTE CANCEL The items of the PICTURE-1 menu are collectively returned to the initial
setting. Note that the items MY MEMORY and CUSTOM - GAMMA are notreset.
PICTURE - 1 Menu (continued)
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
26/5526
PICTURE - 2 Menu
With the PICTURE - 2 menu, the items shown in the table belowcan be performed.
Perform each operation in accordance with the instructions in thetable below.
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
V POSITIONH POSITIONH PHASEH SIZEOVER SCANRESET
2014231134495
: SELECT
Item Description
V POSITION Adjust the Vertical Position: Up Down
This item can be selected only at a RGB input.
H POSITION Adjust the Horizontal Position: Left Right
This item can be selected only at a RGB input.
H PHASE
Adjust the Horizontal Phase (to eliminate flicker) :Right Left This item can be selected only at a RGB input or a COMPONENT VIDEO
input.
H SIZE
Adjust the Horizontal Size: Large Small When this adjustment is excessive, the picture may not be displayed
correctly. In such a case, please press the RESET button during selection ofthis item to reset the H SIZE.
This item can be selected only at a RGB input.
OVER SCAN
Adjust the Over-scan Ratio:Large Small
This item can be selected only at a VIDEO input, a S-VIDEO input or aCOMPONENT VIDEO input.
When this adjustment is too large, a certain degradation may appear at theframe area of the picture. In such a case, please adjust small.
RESET
Reset the PICTURE-2 Menu Items:Selecting the EXECUTE performs this function.
EXECUTE CANCEL The items of the PICTURE-2 menu are collectively returned to the initialsetting. Note that the H PHASE item is not reset.
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
27/55
INPUT Menu
With the INPUT menu, the items shown in the table below can beperformed.
Perform each operation in accordance with the instructions in thetable below.
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
COLOR SPACECOMPONENTVIDEOFRAME LOCK3D-YCSVIDEO NRPROGRESSIVEINFORMATION
AUTOCOMPONENT
AUTOTURN ONNORMALLOWTURN OFF
: SELECT
27
Item Description
COLOR SPACE
Select a Color Space Mode:AUTO RGB SMPTE240 REC709 REC601
This item can be selected only at a RGB input or a COMPONENT VIDEOinput.
When the AUTO is selected, the optimum mode is automatically selected.However, it may not work well at some signals. In such a case, select the
SMPTE240 or REC709 for HDTV signal.
COMPONENT
Select a Function of COMPONENT VIDEO Jacks:COMPONENT SCART RGB
When the SCART RGB is selected, the COMPONENT VIDEO jacks functionas ports for a RGB input with a SCART cable. Refer to the section SignalConnectors of TECHNICAL .
VIDEO
Select a Signal Type Mode:AUTO NTSC PAL SECAM NTSC 4.43 M-PAL N-PAL
This item performs only at a VIDEO input or a S-VIDEO input. For aCOMPONENT VIDEO input, although this item is ineffective, the signal type isidentified automatically even if the AUTO is not selected.
Selecting the AUTO automatically selects the optimum mode. However, itmay not work well at a PAL60 signal and some other signals. If the picturebecomes unstable (ex. a irregular picture, color lack), please select the modedepending on the input signal.
The AUTO operation requires approximately 10 seconds.
FRAME LOCK
Select the Frame Lock Mode:TURN ON TURN OFF
This function performs only at a RGB input with vertical frequency of 48 to 72Hz.
When the TURN ON is selected, a moving picture is displayed moresmoothly.
This function may cause a certain degradation of the picture. In such a case,please select the TURN OFF.
3D-YCS
Select a 3D-YCS mode:STILL IMAGE NORMAL TURN OFF
This function performs only at a VIDEO input of NTSC 3.58.
NORMAL is the mode for images with a lot of motions like movies, and STILLIMAGE is the mode for images with few motions or completely still ones likeslides.
When this function performs, the VIDEO NR function is ineffective.
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
28/5528
Item Description
VIDEO NR
Select a Noise Reduction Mode:
HIGH MIDDLE LOW This function performs only at a VIDEO input or a S-VIDEO input. At a VIDEOinput of NTSC 3.58, this function performs only when the TURN OFF isselected under the 3D-YCS.
When the HIGH, the MIDDLE or the LOW is selected, the noise on screen isreduced according to each mode.
When this function is excessive, it may cause a certain degradation of thepicture.
PROGRESSIVE
Select the Progressive Mode:TV FILM TURN OFF
This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i or 625i signal. The FILMmode is adaptable to the 3-2 Pull-Down system to the conversion.
When the TV or FILM is selected, the screen image will be crisper. But it maycause a certain defect (for example, jagged line) of the picture at a quickmoving object. In such a case, please select the TURN OFF, even though thescreen image may lose the crisp.
This function may cause a certain degradation of the picture. In such a case,please select the TURN OFF.
INFORMATION
Display the Information:Pressing the or the ENTER button performs this function. Use this function when you want the information about the current input (ex.
the resolution and the vertical frequency at a RGB input, the signal type of avideo input) and setting states of the COMPONENT, the VIDEO and theFLAME LOCK.
S2-ASPECT
Select the S2-ASPECT Mode:TURN ON TURN OFF
This function performs only at a S-VIDEO input. When the TURN ON is selected, an S2-Video signal can be identified and the
optimum aspect ratio is automatically selected. When the ASPECT button of the remote control is used or the ASPECT item of
the MAIN menu is operated, the S2-ASPECT mode will be switched to theTURN OFF automatically.
RESET
Reset the INPUT Menu Items:Selecting the EXECUTE performs this function.
EXECUTE CANCEL The items of the INPUT menu are collectively returned to the initial setting.
Note that the INFORMATION item is not reset.
INPUT Menu (continued)
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
29/5529
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
ADJUSTPOWER OFFSEARCHRESET
0 minTURN ON
: SELECT
AUTO Menu
With the AUTO menu, the items shown in the table below can beperformed.Perform each operation in accordance with the instructions in thetable below.
Item Description
ADJUST
Automatically Adjust the Picture:Pressing the or the ENTER button performs this function.At a RGB input: V POSITION, H POSITION, H PHASE and HSIZE are automatically adjusted.
Please use this function with the maximum window size.
At a VIDEO input or S-VIDEO input: This function performs only when the AUTO is selected under the VIDEO item
of the INPUT menu. For a COMPONENT VIDEO input, although this function isineffective, the signal type is identified automatically even if the AUTO is notselected.
This function automatically selects the optimum mode for the input signal.However, it may not work well at a PAL60 signal and some other signals. Ifthe picture becomes unstable (ex. irregular picture, color lack), please usethe function of VIDEO of the INPUT menu.
The operation of this function requires approximately 10 seconds. Also,
please note that it may not function correctly with some input.
POWER OFF
Set the Automatically Power Off Timer:Long (Max. 99 minutes.) Short (Min. 0 minute =DISABLE)
This function performs only when the time is set to 1 to 99. When the set time passes without a valid signal (there is no signal, or the
signal is out of specifications), the projector lamp automatically goes off, andthe POWER indicator begins blinking. Please refer to the section TurningOFF The Power of Power ON/OFF about the turning off.
SEARCH
Automatically Signal Search:
TURN ON TURN OFF If the TURN ON is selected under this item when no signal input is detected,the projector begins searching for an input signal. When an input signal isdetected the projector will cease searching and the picture will appear.
The priority of a search is as follows:RGB VIDEO S-VIDEO COMPONENT VIDEO
If the projector is unstable to find an input signal at any of its ports, it willreturn to the state it was in prior to the search.
RESET
Reset the AUTO Menu Items:Selecting the EXECUTE performs this function.
EXECUTE CANCEL The items of the AUTO menu are collectively returned to the initial setting.
Note that the item ADJUST is not reset.
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
30/5530
SCREEN Menu
With the SCREEN menu, the items shown in the table below can beperformed.Perform each operation in accordance with the instructions in thetable below.
: SELECT
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
BLANKSTART UPMENU POSITIONMESSAGERESET
BLACKTURN ON
TURN ON
Item Description
BLANK
Select a Blank Screen Color:BLUE WHITE BLACK
The blank screen of selected color is displayed by pressing the BLANKbutton. Please refer to the section Temporarily Blanking The Screen ofOperating about the screen blanking.
START UP
Select the Start Up Screen:TURN ON TURN OFF
If the TURN ON is selected when there is no signal or the detected signal isout of specifications, the blank screen is displayed.
MENU POSITION
Adjust a Menu Position:Pressing the or ENTER button start adjusting,
Up
Left Right
Down The button does not finish this item. When you want to return to theprevious display, please press the ESC button.
MESSAGE
Select the Message Mode:TURN ON TURN OFF
When the TURN OFF is selected, the following message functions aredisabled:The message of AUTO IN PROGRESS The message of NO INPUT IS DETECTED
The message of SYNC IS OUT OF RANGE The message while being searched for an input signal, Searching ..The message when an input signal is detected, Detecting ..The indication of the input signal by input change.
RESET
Reset the SCREEN Menu Items:Selecting the EXECUTE performs this function.
EXECUTE CANCEL The items of the SCREEN menu are collectively returned to the initial setting.
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
31/5531
OPTION Menu With the OPTION menu, the items shown in the table below can be performed.Perform each operation in accordance with the instructions in the table below. : SELECT
MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTION
VOLUMESCREEN TYPELAMP TIMEFILTER TIMERESET
164:31234h
21h
Item Description
VOLUME Adjust Volume: High Low
SCREEN TYPE
Select the Screen Type:4:3 16:9 16:9 16-9 Please select the screen type used and the picture position in case of 16:9.
This selection is used as basic information for a suitable display. This functionshould be performed before other picture adjustment.
LAMP TIME
To begin the operation of this item, please press the button of theprojector or the RESET button of the remote control for 3 seconds.Reset the Lamp Timer:Selecting the RESET performs this function.
RESET CANCEL The numerical value of four digits shown on this menu is the projector use
time since the last RESET operation of this item. The value is reset to 0 at thesame time the RESET is selected.
The value of this function is used to display the message of CHANGE THELAMP. So this function must be performed only immediately after replacingthe lamp.Do not perform this function unless you have replaced the lamp. Perform this
function every time the lamp is replaced. Incorrect performing of this functioncauses incorrect operation of the message function.
Please see to the section Lamp about replacing the lamp.
FILTER TIME
To begin the operation of this item, please press the button of theprojector or the RESET button of the remote control for 3 seconds.Reset the Filter Timer:Selecting the RESET performs this function.
RESET CANCEL The numerical value of four digits shown on this menu is the projector use
time since the last RESET operation of this item. The value is reset to 0 at thesame time the RESET is selected.
The value of this function is used to display the message of CLEAN THE AIRFILTER. So this function must be performed only immediately after cleaningor replacing the air filter.Do not perform this function unless you have cleaned or replaced the air filter.Perform this function every time the air filter is cleaned or replaced. Incorrectperforming of this function causes incorrect operation of the messagefunction.
Please see to the section Air Filter about cleaning and replacing the airfilter.
RESET
Reset the OPTION Menu Items:Selecting the EXECUTE performs this function.
EXECUTE CANCEL The SCREEN TYPE item is returned to the initial setting. Note that the items
VOLUME, LAMP TIME and FILTER TIME are not reset.
Multifunctional Settings (continued)
-
8/9/2019 ERSU Guida (test)
32/5532
Lamp
The projector uses a high-pressure mercury glass lamp. The lamp can break with aloud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.Note that each lamp has a different lifetime, and some may burst or burn out soon afteryou start using them. In addition, when the bulb bursts, it is possible for shards ofglass to fly into the lamp housing, and for gas containing mercury to escape from theprojector s vent holes.
If the lamp should break (it will make a loud bang when it does), unplug the powercord from the outlet, and make sure to request a replacement lamp from your localdealer. Note that shards of glass could damage the projector s internals, or causeinjury during handling, so please do not try to clean the projector or replace the lampyourself.
If the lamp should break (it will make a loud bang when it does), ventilate the roomwell, and make sure not to breathe the gas that comes out of the projector vents, orget it in your eyes or mouth.
Do not open the lamp cover while the projector is suspended from above. This isdangerous, since if the lamp s bulb has broken, the shards will fall out when the coveris opened. In addition, working in high places is dangerous, so ask your local dealerto have the lamp replaced even if the bulb is not broken
If the indicators or a message prompts you to replace the lamp (see the section
Related Messages and Regarding the indicator Lamps ), replace the lamp as soonas possible. Using the lamp for long periods of time, or past the replacement date,could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.
If the lamp breaks soon after the first time it is used, it is possible that there areelectrical problems elsewhere besides the lamp. If this happens, contact your localdealer or a service representative.
Use the lamp of the specified type only. Type number: DT00581 (sold separately) Handle with care: jolting or scratching could cause the lamp bulb to burst during use. Before replacing the lamp, make sure the power switch is off and the power cable is
not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handlingthe lamp while hot can cause burns, as well as damaging the lamp.
Do not use the projector with the lamp cover removed. At the lamp replacing, makesure that the screws are screwed in firmly. Loose screws could result in damage orinjury.
Obey local ordinances when disposing of used lamps. In most cases, it is possible todispose of used bulbs in the same manner as used glass bottles, but in some cases,bulbs are sorted separately.
WARNINGHIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
-
8/9/2019 ERSU Guida (test)
33/5533
1 Turn off the projector, and unplug the power cord. Allow the lampbulb to cool for at least 45 minutes.
6 Insert the new lamp, and tighten the 2screws firmly to lock it in place.
Slide the lamp cover into place until it locks into position.
Slowly turn the projector so that the top is facing up.
3 After making sure that the projectorhas cooled adequately, slowly flipover the projector, so that the bottomis facing up.
4 Hold the release button while slidingand taking up the lamp cover.
2 Contact your local dealer to prepare a new lamp. Tell the dealeryour lamp type number. If the projector is mounted on the ceiling,or if the lamp has broken, also ask the dealer to replace the lamp.
9 Turn on the projector, and reset the lamp timer. When the lamp hasbeen replaced after the message of THE POWER WILL TURN OFFAFTER 0hr. is displayed, complete the following operation within10 minutes of switching power on.(1) While the projector running, press the MENU button to open the menu.
(2) Choose the OPTION on the menu using the / button, then press the buttonor ENTER button.(3) Choose the LAMP TIME using the / button, then press and hold the button
of projector or the RESET button of remote control for 3 seconds.(4) Choose the RESETusing the button.
In the case of replacement by yourself,
5 Unscrew the 2 screws, and slowlypick up the lamp by the handles.
Replacing The Lamp
WARNING Please carefully read the Users Manual - Safety Guide.CAUTION Do not reset the lamp timer without replacing the lamp.
When you replace the lamp, please replace also the air filter. The air filter may beattached when you buy a replacement lamp for this projector. Please ask your dealer.
If the indicators or a message prompts you to replace the lamp, replace the lamp as soonas possible. Using the lamp for long periods of time, or past the replacement date, couldcause it to burst. If the projector is mounted on the ceiling, or if the lamp has broken, donot try to clean the projector or replace the lamp yourself.
Lamp cover
Release button
Handles
Screws
7
8
Lamp (continued)
-
8/9/2019 ERSU Guida (test)
34/5534
Air Filter
Caring For The Air Filter The air filter should be cleaned about every 100 hours. If the indicators or a messageprompts you to clean the air filter (see the section Related Messages and RegardingThe Indicator Lamps ), clean the air filter as soon as possible. If the air filter becomesclogged by dust or the like, internal temperature rises and could cause malfunction.
1 Turn off the projector, and unplug the power cord.
2 Apply a vacuum cleaner tothe top of the filter cover toclean the air filter.
3 Reset the filter timer.
Filter Cover
WARNING Please carefully read the Users Manual - Safety Guide. Before replacing the air filter, make sure the power switch is off and the power cableis not plugged in. Use the air filter of the specified type only. Type number: NJ08292 (sold separately)
Do not use the projector with the air filter and filter cover removed. The use withoutthe air filter could result in damage.
CAUTION Do not reset the filter timer without cleaning or replacing the air filter. If the air filter becomes clogged by dust or the like, internal temperature rises andcould cause malfunction. The power is automatically turned off in order to prevent theprojector from overheating internally. When you replace the lamp, please replace also the air filter. The air filter may beattached when you buy a replacement lamp for this projector. Please ask your dealer.
(1) Turn on the projector. While the projector running, press the MENU button toopen the menu.(2) Choose the OPTION on the menu using the / button, then press the
button or ENTER button.(3) Choose the FILTER TIME using the / button, then press and hold the
button of projector or the RESET button of remote control for 3 seconds.(4) Choose the RESET using the button.
-
8/9/2019 ERSU Guida (test)
35/5535
Replacing The Air Filter
Filter cover
Air filter
Release buttons
Release buttons
Turn off the projector, and unplug the power cord.
2 Contact your local dealer to prepare anew air filter. Tell the dealer your airfilter type number.
4 Hold the release buttons of the airfilter, while pulling down it.
3 After making sure that the projectorhas cooled adequately, remove thefilter cover. Hold the release buttons of
the filter cover, while pulling up it.
6 Reset the filter timer.(1) Turn on the projector. While the projector running, press the MENU button to
open the menu.(2) Choose the OPTION on the menu using the / button, then press the
button or ENTER button.(3) Choose the FILTER TIME using the / button, then press and hold the
button of projector or the RESET button of remote control for 3 seconds.(4) Choose the RESET using the button.
If the soiling will not come off the air filter, or it becomes damaged, then it needs to bereplaced. Please replace the air filter as soon as possible.
1
Insert a new air filter, and replace the filter cover.5
Air Filter (continued)
-
8/9/2019 ERSU Guida (test)
36/5536
Other Care
WARNING Please carefully read the Users Manual - Safety Guide. Before replacing the air filter, make sure the power switch is off and the power cableis not plugged in.ATTENTION Do not use cleaners or chemicals other than those listed below,including benzene and paint thinner. Do not use aerosols or sprays. Do not polish or wipe with hard objects.
Caring For The Inside Of The Projector
Caring For The Lens
In order to ensure the safe use of your projector, please have it cleaned and inspected byyour local dealer about once every 2 years. Never try to care for the inside of the unit
yourself. Doing so is dangerous.
1 Turn off the projector, and unplug thepower cord.
2Lightly wipe the lens with acommercially available lens-cleaningwipe. Do not touch the lens directlywith your hand.
Caring For The Cabinet And Remote Control
1 Turn off the projector, and unplug the power cord.
2 Wipe lightly with gauze or a soft cloth.If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, andwipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
Lens
-
8/9/2019 ERSU Guida (test)
37/5537
Troubleshooting
Related Messages
When the unit's power is ON, messages such as those shown below may be displayed.When any such message is displayed on the screen, please respond as describedbelow. If the same message is displayed after the treatment, or if a message other thanthe following appears, please contact your dealer or service company.
Message Description
CHANGE THE LAMPAFTER REPLACING LAMP,RESET THE LAMP TIMER.
(*1)
Lamp usage time is approaching 2000 hours. (*2)Preparation of a new lamp, and an early lamp change isrecommended. After you have changed the lamp, please besure to reset the lamp timer.
CHANGE THE LAMPAFTER REPLACING LAMP,RESET THE LAMP TIMER.
THE POWER WILL TURN OFFAFTER ** hr.
(*1)
Lamp usage time is approaching 2000 hours. (*2)A lamp change within ** hours is recommended. When lampusage reaches 2000 hours, the power will automatically beturned OFF. Please change the lamp by referring to the Lamp section of this manual. After you have changed the lamp,please be sure to reset the lamp timer.
CHANGE THE LAMPAFTER REPLACING LAMP,RESET THE LAMP TIMER.
THE POWER WILL TURN OFFAFTER 0 hr.
As lamp use has reached 2000 hours (*2), the power will soonbe automatically turned OFF.Please immediately turn the power off, and change the lamp byreferring to the Lamp section of this manual. After you havechanged the lamp, please be sure to reset the lamp timer.
NO INPUT IS DETECTED
ON ***
There is no input signal.Please confirm the signal input connection, and the status of thesignal source.
SYNC IS OUT OF RANGEON *** *****kHz *****Hz
The horizontal or vertical wavelength of the inputted signal isoutside of the response parameters of this unit.Please confirm the specs for this unit or the signal sourcespecs.
CHECK THE AIR FLOW
The internal portion temperature is rising.Please turn the power OFF, and allow the unit to cool down atleast 20 minutes. After having confirmed the following items,please turn the power ON again. Is there blockage of the air passage aperture? Is the air filter dirty? Does the peripheral temperature exceed 35 C?
(*1) Although this message will be automatically disappeared after around 3 minutes, it will be reappearedevery time the power is turned ON.(*2) Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will longer light up, or the lamp will break or burst, etc. This unit is equipped with an automatic shut-down function, suchthe power will automatically be turned OFF when lamp usage time has reached 2,000 hours. Please be aware, howevthat among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior tofunctioning of the automatic shut-down function of this unit.
NOTE
fH fV
-
8/9/2019 ERSU Guida (test)
38/5538
Wipe the dust-detecting window byusing a soft cloth.
Troubleshooting (continued)Related Messages (continued)
Message Description
CLEAN THE AIR FILTER
POWER OFF FIRST,THEN CLEAN THE AIR FILTER.AFTER CLEANING THE AIR
FILTER,RESET THE FILTER TIMER.
A note of precaution when cleaning the air filter.Please immediately turn the power OFF, and clean or changethe air filter by referring to the Air Filter section of this manual.After you have cleaned or changed the air filter, please be sureto reset the filter timer.If the same message is displayed after the treatment, pleaseclean the transparent area of filter cover and the dust-detectingwindow, according to the following.
ATTENTION The transparent area of filter cover and the dust-detecting windowshould be cleaned for normal operation of the optical dust detecting system. Pleasepay attention not to remain fiber or fragment of cloth inside the duct.
Filter cover
Air filter
Release buttons
Release buttons
Turn off the projector, and unplug thepower cord.
2 After making sure that the projectorhas cooled adequately, remove thefilter cover.Hold the release buttons of the filter cover, whilepulling up it.
4 Remove the air filter.Hold the release buttons of the air filter, while pullingdown it.
1
Replace the air filter and filter cover.
Transparent area
Filter cover
Dust detecting window
3 Wipe the transparent area of the filtercover by using a swab or a soft cloth.
5
6
(Rear side)
(Bottom side)
-
8/9/2019 ERSU Guida (test)
39/5539
ATTENTION When the interior portion has become overheated, for safetypurposes, the power source is automatically turned off, and the indicator lamps mayalso be turned off. In such a case, press the (power OFF) side of the main powerswitch, and wait at least 45 minutes. After the unit has sufficiently cooled down, pleasemake confirmation of the attachment state of the lamp and lamp cover, and then turnthe power on again.
Regarding The Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicatorhave the meanings as described in the table below. Please respond in accordance with theinstructions within the table. If the same indication is displayed after the treatment, or if anindication other than the following is displayed, please contact your dealer or service
company.POWERindicator
LAMPindicator
TEMPindicator Description
Lighting inorange
Turned off Turned off The unit is in a standby state. Please refer to the PowerON/OFF section of this manual.
Flashing ingreen
Turned off Turned off The unit is warming up. Please wait.
Lighting ingreen
Turned off Turned off The unit is in an ON state. Ordinary operations may beperformed.
Flashing inorange
Turned off Turned off The unit is cooling down. Please wait.
Blinking inred
- -
The unit is cooling down. A certain error has been detected.Wait until the POWER indicator has finished flashing, and thenperform the proper response measure using the itemdescriptions below as reference.
Lighting or
blinking inred
Lighting inred Turned off
The projector lamp has not been properly fixed (attached),the projector lamp does not light, and/or there is a possibilitythat the interior portion has become heated. Turn the powerOFF and wait at least 20 minutes. After the unit has sufficientlycooled down, please make confirmation of the following items,and then turn the power ON again. If the same indication isdisplayed, please change the lamp.
Is there blockage of the air passage aperture? Is the air filter is dirty? Does the peripheral temperature exceed 35 C?
Lighting orblinking in
red
Blinking in
redTurned off
The lamp cover has not been properly fixed (attached). Turnthe power OFF and wait at least 45 minutes. After the unit hassufficiently cooled down, please make confirmation of theattachment state of the lamp and lamp cover, and then turnthe power ON again.
Troubleshooting (continued)
-
8/9/2019 ERSU Guida (test)
40/5540
POWERindicator
LAMPindicator
TEMPindicator Description
Lighting orblinking in
redTurned off
Blinking inred
The cooling fan is not operating. Turn the power OFF and waitat least 20 minutes. After the unit has sufficiently cooled down,please make confirmation of the following item, and thenresent the power to ON.
Is there no foreign matter caught in the cooling fan?
Lighting orblinking in
redTurned off
Lighting inred
There is a possibility that the interior portion has becomeheated. Turn the power OFF and wait at least 20 minutes.After the unit has sufficiently cooled down, please makeconfirmation of the following item, and then resent the powerto ON.
Is there blockage of the air passage aperture? Is the air filter is dirty? Does the peripheral temperature exceed 35 C?
Lighting ingreen
Alternative blinking inthe red
There is a possibility that the interior portion has becomeovercooled. Please use the unit within the usage temperatureparameters (0 C to 35 C). After the treatment, resent thepower to ON.
Lighting in
green
Simultaneous blinking
in red
It is time to clean the air filter, or there is no air filter. Pleaseimmediately turn the power OFF, and clean or change the airfilter by referring to the Air Filter section of this manual. After
you have cleaned or changed the air filter, please be sure toreset the filter timer. After the treatment, resent the power toON.
Regarding The Indicator Lamps (continued)
Troubleshooting (continued)
-
8/9/2019 ERSU Guida (test)
41/5541
WARNING Please carefully read the Users Manual - Safety Guide.Never use the projector if abnormal operations such as smoke, strange odor, excessive
sound, damaged casing or elements or cables, penetration of liquids or foreign matter,etc. should occur.
Phenomena That May Easily Be Mistaken For Machine Defects
Although bright spots or dark spots may appear on the screen, this is aunique characteristic of liquid crystal displays, and such do not constitute or imply amachine defect.
NOTE
Before requesting repair, please check in accordance with the following chart. If thesituation cannot be corrected, then contact your dealer.
Phenomenon Cases not involving a machine defect,and Items to be confirmedReference
pages
Power does notcome ON.
The main power source is not ON.Turn on the main power.
11,14The electrical power cord is not plugged in.Correctly connect the power cord.The main power source has been interrupted during operation,such as by a power outage (blackout), etc.Be sure to press the (power OFF) side of the main power switch,
and leave this OFF for at least 20 minutes. After the unit hassufficiently cooled down, turn ON the power source.
14
Neither soundsnor pictures areoutputted.
The input changeover settings are mismatched.Select the input signal, and correct the settings. 15
No signal is being inputted.Correctly connect the connection cables. 10
Pictures aredisplayed,but no soundsare heard.
The electrical wiring to this unit is not correctly connected.Correctly connect the connection cables. 10
The volume setting has been set at (or adjusted to) anextremely low level.
Adjust the VOLUME setting to a higher level.
17
The MUTE mode is the current setting.Press the MUTE button to release (change) the MUTE mode setting. 17
Sounds areheard,but no picturesare displayed.
The electrical wiring to this unit is not correctly connected.Correctly connect the connection cables. 10
The brightness setting has been set at (or adjusted to) anextremely low level.Adjust the BRIGHT setting to a brighter level.
23
The lens cap has not been removed.Remove the lens cap. 4,14
Colors have afaded- outappearance, orColor tone ispoor.
Color settings are not correctly adjusted.Perform picture adjustments by changing the COLOR BAL R,COLOR BAL G, COLOR BAL B, COLOR, and/or the TINT settings,etc.
24
Troubleshooting (continued)
-
8/9/2019 ERSU Guida (test)
42/5542
Phenomenon Cases not involving a machine defect,and Items to be confirmedReference
pages
Pictures appeardark.
The brightness setting and/or contrast setting has not beenproperly adjusted.Perform picture adjustments by changing the BRIGHT and/orCONTRAST settings, etc. 23
The WHISPER mode is the current setting.Change (by releasing) from the WHISPER mode.Lamp is approaching the end of its product lifetime.Exchange the old lamp with a new lamp.
32,33
Pictures appearblurry.
Either the FOCUS setting or the H PHASE is not properlyadjusted.
Adjust the focus and the H PHASE setting.
15,26
The lens is dirty or misty.Clean the lens.
36
Warranty And After-Service
If a problem occurs with the equipment, first refer to the Troubleshooting section of thismanual, and run through the suggested checks. If this does not resolve the problemcontact your dealer or service company. They will tell you what warranty condition isapplied.
Phenomena That May Easily Be Mistaken For Machine Defects (continued)
Troubleshooting (continued)
-
8/9/2019 ERSU Guida (test)
43/5543
This specifications are subject to change without notice.NOTE
Item SpecificationProduct name Liquid crystal projector
Liquidcrystalpanel
Panel size 1.4 cm (0.55 type)
Drive system TFT active matrix
Pixels 480,000 pixels (800 horizontal x 600 vertical)
Lens Zoom lens F=1.6 ~ 1.8 f=16.8 ~ 20.1 mm
Lamp 130W UHB
Speaker 1.0W
Power supply AC100 ~ 120V, 2.4A / AC220 ~ 240V, 1.1A
Power consumption 220W
Temperature range 0 ~ 35 C (Operating)
Size 332 (W) x 92 (H) x 254 (D) mm (Not including protruding parts)
Weight (mass) 2.94 kg
Ports
Optional Parts Lamp: DT00581 Air Filter: NJ08292
For others, consult your dealer.
RGB Input PortsRGB ................................1VIDEO Input PortsVIDEO ............................1S-VIDEO ........................1COMPONENT VIDEO(CR /P R, C B /P B, Y) ............1
AUDIO PortsAUDIO ............................1AUDIO R, L.....................1CONTROL PortsCONTROL ....................1
A C I N
332
85.5
2 5 4
1 1 0
3 9
9 2
7 1
Specifications
-
8/9/2019 ERSU Guida (test)
44/551
In this section, the technical information about this projector is described.
The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
RADEMARK ACKNOWLEDGEMENT : VGA and XGA are registered trademarks of the International Business Machines Corporation. Apple and Mac are registered trademarks of Apple Computer, Inc.
VESA and SVGA are trademarks of the Video Electronics Standard Association. Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
NOTE
WARNING Before using, read the "User's Manual - Safety Guide" and thesemanuals to ensure correct usage through understanding. After reading, store
them in a safe place for future reference.
TECHNICAL
Projector
CP-S210/CP-S210T/CP-S210FCP-S210W/CP-S210WT/CP-S210WF
User's Manual - Operating Guide
-
8/9/2019 ERSU Guida (test)
45/552
Signal ConnectorsL-AUDIO-RVIDEO
S-VIDEO
AUDIO
YCOMPONENT VIDEO
CB / P B CR / P R
RGB CONTROL2 1 34 5 610
7 8 9
Port Specification
RGB1 Video signal: RGB separate, Analog, 0.7 Vp-p, 75 terminator (positive)H/V. sync. signal:TTL level (positive/negative)Composite sync. signal: TTL levelD-sub 15-pin shrink jack
AUDIO(interlocked port)1
2 200 mVrms, 50 k (max. 3.0 Vp-p), Stereo mini jack
CONTROL3 D-sub 9-pin plug
VIDEO4 1.0 Vp-p, 75 terminator, RCA jack
AUDIO L, R(interlocked
/ / )109874
65
200 mVrms, 50 k (max. 3.0 Vp-p), RCA jack
COMPONENT VIDEO
Y, C B /P B,
CR /P R9
87Y signal: 1.0 Vp-p, 75 terminatorCB /P B signal: 0.7 Vp-p, 75 terminator
CR /P R signal: 0.7 Vp-p, 75 terminator
S-VIDEO10Mini Din 4-pin jack
11 12 13 14 15
109876
1 2 3 4 5
6789
5 4 3 2 1
No. Signal No. Signal No. Signal1 Video input Red 6 Ground Red 11 -2 Video input Green 7 Ground Green 12 SDA (DDC)
3 Video input Blue 8 Ground Blue 13 H. sync./Compositesync.4 - 9 Ground 14 Vertical sync5 Ground 10 - 15 SCL (DDC)
No. Signal No. Signal No. Signal1 - 4 - 7 RTS2 RD 5 Ground 8 CTS3 TD 6 - 9 -
No. Signal
1 Color signal: 0.286 Vp-p (NTSC, burst), 75 terminator
Color signal: 0.300 Vp-p (PAL/SECAM, burst), 75 terminator2 Brightness signal: 1.0 Vp-p, 75 terminator3 Ground4 Ground
TECHNICALTECHNICAL
12
4 3
-
8/9/2019 ERSU Guida (test)
46/553
Example Of Computer Signal
ResolutionH V
fH (kHz) fV (Hz) Rating Signal modeDisplaymode
720 400 37.9 85.0 VESA TEXT Zoom in
640 480 31.5 59.9 VESA VGA (60Hz) Zoom in
640 480 35.0 66.7 Mac13"mode Zoom in
640 480 37.9 72.8 VESA VGA (72Hz) Zoom in
640 480 37.5 75.0 VESA VGA (75Hz) Zoom in
640 480 43.3 85.0 VESA VGA (85Hz) Zoom in
800 600 35.2 56.3 VESA SVGA (56Hz)
800 600 37.9 60.3 VESA SVGA (60Hz)
800 600 48.1 72.2 VESA SVGA (72Hz)
800 600 46.9 75.0 VESA SVGA (75Hz)800 600 53.7 85.1 VESA SVGA (85Hz)
832 624 49.7 74.5 Mac16"mode Zoom out
1024 768 48.4 60.0 VESA XGA (60Hz) Zoom out
1024 768 56.5 70.1 VESA XGA (70Hz) Zoom out
1024 768 60.0 75.0 VESA XGA (75Hz) Zoom out
1024 768 68.7 85.0 VESA XGA (85Hz) Zoom out
1152 864 67.5 75.0 VESA SXGA (75Hz) Zoom out
1280 960 60.0 60.0 VESA SXGA (60Hz) Zoom out
1280 1024 64.0 60.0 VESA SXGA (60Hz) Zoom out
1280 1024 80.0 75.0 VESA SXGA (75Hz) Zoom out
1280 1024 91.2 85.0 VESA SXGA (85Hz) Zoom out
1600 1200 75.0 60.0 VESA UXGA (60Hz) Zoom out
Some computers may have multiple display screen modes. Use of some of thesemodes will not be possible with this projector. Be sure to check jack type, signal level, timing and resolution before connecting this projector to a
computer. Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above. Although the projector can display signals with resolution up to UXGA (1,600 x 1,200), the signal will
be converted to the projectors panel resolution before being displayed. The best displayperformance will be achieved if the resolutions of the input signal and projector panel are identical.
The image may not be displayed correctly when the input sync. signal is Composite Sync. orSync. on G.
Automatically adjustment may not function correctly with some input signals. When the image resolution is changed on a computer, depending on an input, automatic adjust
function may take some time and may not be completed. In this case, you may not be able to see acheck box to select Yes/No for the new resolution on Windows. Then the resolution will go back tothe original. It might be recommended to use other CRT or TFT monitors to change the resolution.
NOTE
-
8/9/2019 ERSU Guida (test)
47/554
Initial Set SignalsThe following signals are used for the initial settings.The signal timing of some computer models may be different. In such case, refer toadjust the V.POSIT and H.POSIT of the menu.
D A T A
H S Y N C
D A T A
V S Y N C
Display interval cBack porch b
Sync a
Front porch dDisplay interval c
Back porch b
Sync a
Front porch d
Computer / Signal
Horizontal signal timing (s)
a b c dTEXT 2.0 3.0 20.3 1.0
VGA (60Hz) 3.8 1.9 25.4 0.6
Mac 13"mode 2.1 3.2 21.2 2.1
VGA (72Hz) 1.3 3.8 20.3 1.0
VGA (75Hz) 2.0 3.8 20.3 0.5
VGA (85Hz) 1.6 2.2 17.8 1.6
SVGA (56Hz) 2.0 3.6 22.2 0.7
SVGA (60Hz) 3.2 2.2 20.0 1.0
SVGA (72Hz) 2.4 1.3 16.0 1.1
SVGA (75Hz) 1.6 3.2 16.2 0.3
SVGA (85Hz) 1.1 2.7 14.2 0.6
Mac 16"mode 1.1 3.9 14.5 0.6
XGA (60Hz) 2.1 2.5 15.8 0.4
XGA (70Hz) 1.8 1.9 13.7 0.3
XGA (75Hz) 1.2 2.2 13.0 0.2
XGA (85Hz) 1.0 2.2 10.8 0.5
1152 864 (75Hz) 1.2 2.4 10.7 0.61280 960 (60Hz) 1.0 2.9 11.9 0.9
1280 1024 (60Hz) 1.0 2.3 11.9 0.4
1280 1024 (75Hz) 1.1 1.8 9.5 0.2
1280 1024 (85Hz) 1.0 1.4 8.1 0.4
1600 1200 (60Hz) 1.2 1.9 9.9 0.4
Computer / Signal
Vertical signal timimg (lines)
a b c dTEXT 3 42 400 1
VGA (60Hz) 2 33 480 10
Mac 13"mode 3 39 480 3
VGA (72Hz) 3 28 480 9
VGA (75Hz) 3 16 480 1
VGA (85Hz) 3 25 480 1
SVGA (56Hz) 2 22 600 1
SVGA (60Hz) 4 23 600 1
SVGA (72Hz) 6 23 600 37
SVGA (75Hz) 3 21 600 1
SVGA (85Hz) 3 27 600 1
Mac 16"mode 3 39 624 1
XGA (60Hz) 6 29 768 3
XGA (70Hz) 6 29 768 3
XGA (75Hz) 3 28 768 1
XGA (85Hz) 3 36 768 1
1152 864 (75Hz) 3 32 864 11280 960 (60Hz) 3 36 960 1
1280 1024 (60Hz) 3 38 1024 1
1280 1024 (75Hz) 3 37 1024 2
1280 1024 (85Hz) 3 44 1024 1
1600 1200 (60Hz) 3 46 1200 1
-
8/9/2019 ERSU Guida (test)
48/555
RS-232C Communication
19200bps, 8N1
1. ProtocolConsist of header (7 bytes) + command data (6 bytes).
2. HeaderBE + EF + 03 + 06 + 00 + CRC_low + CRC_highCRC_low : Lower byte of CRC flag for command dataCRC_high : Upper byte of CRC flag for command data
3 Command dataCommand Data Chart
Connecting The Cable
Communications Setting
(1) Turn off the projector and the computer power supplies.(2) Connect the CONTROL port of the projector with a RS-232C port of the computer by a RS-
232C cable. Use the cable that fulfills the specification shown in the following figure.(3) Turn on the computer power supply and after the computer has started up, turn on theprojector power supply.
byte_0 byte_1 byte_2 byte_3 byte_4 byte_5
Action Type Setting codelow high low high low high
Action (byte_0 - 1)
Action Classification Content
1 SET Change setting to desired value.
2 GET Read projector internal setup value.
4 INCREMENT Increment setup value by 1.
5 DECREMENT Decrement setup value by 1.6 EXECUTE Run a command.
CONTROLport
D-sub 9-pinplug
RS-232C port
D-sub 9-pinplug
D-sub 9-pin jack
D-sub 9-pin jack
1234567
89
RDTD
GND
CTSRTS
1234567
89
CDRDTDDTRGNDDSRRTS
DTSRI
Projector RS-232C cross cable Computer
6789
5 4 3 2 1
9876
1 2 3 4 5 6789
5 4 3 2 1
9876
1 2 3 4 5
-
8/9/2019 ERSU Guida (test)
49/556
RS-232C Communication (continued)Requesting projector status (Get command)(1) Send the request code Header + Command data (02H+00H+ type (2bytes)+00H+00H) from the computer to the projector.(2) The projector returns the response code 1DH+ data (2 bytes) to the computer.
Changing the projector settings (Set command)(1) Send the setting code Header + Command data (01H+00H+ type (2 bytes) +setting code (2 bytes)) from the computer to the projector.(2) The projector changes the setting based on the above setting code.(3) The projector returns the response code 06H to the computer.
Using the projector default settings (Reset Command)(1) The computer sends the default setting code Header + Command data (06H+00H+type (2 bytes) +00H+00H) to the projector.(2) The projector changes the specified setting to the default value.(3) The projector returns the response code 06H to the computer.
Increasing the projector setting value (Increment command)(1) The computer sends the increment code Header + Command data (04H+00H+type (2 bytes) +00H+00H) to the projector.(2) The projector in creases the setting value on the above setting code.(3) The projector returns the response code 06H to the computer.
Decreasing the projector setting value (Decrement command)(1) The computer sends the decrement code Header + Command data (05H+00H+type (2 bytes) +00H + 00H) to the projector.(2) The projector decreases the setting value on the above setting code.(3) The projector returns the response code 06H to the computer.
When the projector cannot understand the received commandWhen the projector cannot understand the received command, the error code 15H issent back to the computer.Sometimes the projector cannot properly receive the command. In such a case, thecommand is not executed and the error code 15H is sent back to the computer. If thiserror code is returned, send the same command again.
When the projector cannot execute the received command.
When the projector cannot execute the received command, the error code 1cH +xxxxH is sent back to the computer. When the data length is greater than indicated bythe data length code, the projector ignore the excess data code.Conversely when the data length is shorter than indicated by the data length code, anerror code will be returned to the computer.
Operation cannot be guaranteed when the projector receives anundefined command or data. Provide an interval of at least 40ms between the response code and any other code. The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data. Commands are not accepted during warm-up.
NOTE
-
8/9/2019 ERSU Guida (test)
50/557
Command Data Chart
Names Operation type HeaderCommand data
CRC Action Type Setting code
Keystone
Get BE EF 03 06 00 B9 D3 02 00 07 20 00 00
Increment BE EF 03 06 00 DF D3 04 00 07 20 00 00Decrement BE EF 03 06 00 0E D2 05 00 07 20 00 00
Keystone Reset Execute BE EF 03 06 00 08 D0 06 00 0C 70 00 00
Brightness
Get BE EF 03 06 00 89 D2 02 00 03 20 00 00
Increment BE EF 03 06 00 EF D2 04 00 03 20 00 00
Decrement BE EF 03 06 00 3E D3 05 00 03 20 00 00
Brightness Reset Execute BE EF 03 06 00 58 D3 06 00 00 70 00 00
Contrast
Get BE EF 03 06 00 FD D3 02 00 04 20 00 00
Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00
Decrement BE EF 03 06 00 4A D2 05 00 04 20 00 00Contrast Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00
AspectSet
4:3 BE EF 03 06 00 9E D0 01 00 08 20 00 0016:9 BE EF 03 06 00 0E D1 01 00 08 20 01 0015:9 BE EF 03 06 00 6E D0 01 00 08 20 03 00
32:15 BE EF 03 06 00 5E D2 01 00 08 20 04 00WIDE BE EF 03 06 00 CE D3 01 00 08 20 05 00ZOOM BE EF 03 06 00 3E D3 01 00 08 20 06 00
Get BE EF 03 06 00 AD D0 02 00 08 20 00 00
WhisperSet
NORMAL BE EF 03 06 00 3B 23 01 00 00 33 00 00
WHISPER BE EF 03 06 00 AB 22 01 00 00 33 01 00Get BE EF 03 06 00 08 23 02 00 00 33 00 00
MirrorSet
Normal BE EF 03 06 00 C7 D2 01 00 01 30 00 00H Inverse BE EF 03 06 00 57 D3 01 00 01 30 01 00V lnverse BE EF 03 06 00 A7 D3 01 00 01 30 02 00
H&V Inverse BE EF 03 06 00 37 D2 01 00 01 30 03 00Get BE EF 03 06 00 F4 D2 02 00 01 30 00 00
RS-232C Communication (continued)
-
8/9/2019 ERSU Guida (test)
51/558
Command Data Chart (continued)
RS-232C Communication (continued)
Names Operation type HeaderCommand data
CRC Action Type Setting code
LanguageSet
English BE EF 03 06 00 F7 D3 01 00 05 30 00 00
FRANAIS BE EF 03 06 00 67 D2 01 00 05 30 01 00Deutsch BE EF 03 06 00 97 D2 01 00 05 30 02 00ESPAOL BE EF 03 06 00 07 D3 01 00 05 30 03 00
Italiano BE EF 03 06 00 37 D1 01 00 05 30 04 00Norsk BE EF 03 06 00 A7 D0 01 00 05 30 05 00
Nederlands BE EF 03 06 00 57 D0 01 00 05 30 06 00PORTUGUS BE EF 03 06 00 C7 D1 01 00 05 30 07 00
BE EF 03 06 00 37 D4 01 00 05 30 08 00BE EF 03 06 00 A7 D5 01 00 05 30 09 00BE EF 03 06 00 57 D5 01 00 05 30 0A 00
SVENSKA BE EF 03 06 00 C7 D4 01 00 05 30 0B 00BE EF 03 06 00 F7 D6 01 00 05 30 0C 00SUOMI BE EF 03 06 00 67 D7 01 00 05 30 0D 00POLSKI BE EF 03 06 00 97 D7 01 00 05 30 0E 00Get BE EF 03 06 00 C4 D3 02 00 05 30 00 00
GammaSet
NORMAL BE EF 03 06 00 C7 F0 01 00 A1 30 00 00
CINEMA BE EF 03 06 00 57 F1 01 00 A1 30 01 00
DYNAMIC BE EF 03 06 00 A7 F1 01 00 A1 30 02 00
CUSTOM BE EF 03 06 00 07 FD 01 00 A1 30 10 00
Get BE EF 03 06 00 F4 F0 02 00 A1 30 00 00
Custom Gamma
Get BE EF 03 06 00 08 F1 02 00 A0 30 00 00
Increment BE EF 03 06 00 6E F1 04 00 A0 30 00 00
Decrement BE EF 03 06 00 BF F0 05 00 A0 30 00 00
CustomColor Temp
Set
USER BE EF 03 06 00 3B F8 01 00 B0 30 10 00
HIGH BE EF 03 06 00 0B F5 01 00 B0 30 03 00MIDDLE BE EF 03 06 00 9B F4 01 00 B0 30 02 00
LOW BE EF 03 06 00 6B F4 01 00 B0 30 01 00
Get BE EF 03 06 00 C8 F5 02 00 B0 30 00 00
Custom User RSet
50 BE EF 03 06 00 57 F7 01 00 B1 30 05 00
60 BE EF 03 06 00 C7 F6 01 00 B1 30 04 00
70 BE EF 03 06 00 F7 F4 01 00 B1 30 03 0080 BE EF 03 06 00 67 F5 01 00 B1 30 02 0090 BE EF 03 06 00 97 F5 01 00 B1 30 01 00
100 BE EF 03 06 00 07 F4 01 00 B1 30 00 00
Get BE EF 03 06 00 34 F4 02 00 B1 30 00 00
Custom User GSet
50 BE EF 03 06 00 13 F7 01 00 B2 30 05 00
60 BE EF 03 06 00 83 F6 01 00 B2 30 04 00
70 BE EF 03 06 00 B3 F4 01 00 B2 30 03 00