-
ECOCOMPACTCompattatori per Rifiuti
Raggiungimento di alte concentrazioni;
Facile trasporto e sollevamento del compattato;
Agevole installazione anche in condizioniparticolarmente gravose;
Robustezza e semplicità costruttiva;
Prolungata affidabilità;
Azionamento realizzato a mezzocircuito oleodinamico
High concentrations;
Compacted material easy to transport and lift;
Easy to install even in particularly difficult locations;
Strong and simple construction;
Long-term reliability;
Operation by hydraulic-oil pump unit.
Waste Compactor
-
ECOCOMPACT Compattatori pe r rifiuti - Waste Compactor
Via Vicinale delle Pianacce, 8 - 55010 CAMIGLIANO - Lucca, Italy Tel. ++39 0583.920342 Fax. ++39 0583.920335www.inoxbf.it [email protected]
LECOCOMPACT è stato concepito per ridurre il volume deicontaminati ed eliminare per quanto possibile lacqua in essi conte-nuta.Nello stesso tempo la spinta di compattazione tramite un canaleinclinato consente il trasferimento del materiale a distanze compre-se tra i sette e gli otto metri ed il suo sollevamento fino a cinquemetri daltezza.Lapparecchio è costituito da un corpo in due metà imbullonate traloro, realizzate con lamiere ad alto spessore e con costolature dirinforzo per garantirne lindeformabilità pur essendone sottopostoad altissime pressioni interne.La parte posteriore è destinata al caricamento del materiale, allaseparazione dei liquidi e allalloggiamento del pistone di spinta; laparte anteriore invece è destinata alla disidratazione finale degli scartitramite la spinta di compattazione e la contropressione esercitatada un portello regolabile che consente levacuazione del materialeattraverso il canale.LECOCOMPACT viene costruito in tre diversi modelli caratte-rizzati dalle differenti capacità di compattazione, dai valori di com-
pressione ed dalla produttività di ciascun modello come indicato nella tabella qui sotto riportata. Ciascun modello inoltreprevede la costruzione in lamiera ed acciaio al carbonio zincato a caldo o in acciaio inox AISI 304L e 316L. Lapparec-chio viene fornito completo di centralina oleodinamica che prevede limpiego di due motori e due pompe per lalimenta-zione separata del circuito di compattazione e di contropressione.Un pannello di comando con tutte le apparecchiature elettriche per lazionamento motori viene fornito con un PLC, chetramite una tastiera dimpostazione, gestisce la funzionalità dei cicli di lavorazione programmati.
45-55
45-55
45-55
%
0,3
0,5
1,1
MC
VOLU
ME
DI
CAR
ICAM
ENTO
800x700
1000x900
MM
700x620
DIM
ENSI
ON
IBO
CCA
DI
SCAR
ICO
7,5
15
22
KW
SPINTA CONTROP.
0,75
1,5
1,5
KW
MO
TOR
ID
ELLA
CEN
TRAL
EID
RAU
LICA
TEM
PO D
ELCI
CLO
AVU
OTO
46 sec.
70 sec.
40 sec.
TEM
PO D
ELCI
CLO
API
ENO
120 sec.
150 sec.
94 sec.
SECC
OM
EDIO
T/24H
15-25
25-45
10-15
PRO
DU
ZIO
NE
IC20
IC22
TIPO
IC181.INGRESSO MATERIALE2.PISTONE DI COMPRESSIONE3.SPORTELLO DI CONTROPRESSIONE4.PISTONE DI CONTROPRESSIONE5.SCARICO MATERIALE6.CAMERA DI ALIMENTAZIONE 7.CAMERA DI COMPRESSIONE 8.ZONA DI CONTROPRESIONE
The ECOCOMPACT was designed to reduce the volume of contaminants and to remove as much water from themas possible.At the same time, the compacting thrust along an inclined channel allows the material to be conveyed to distances ofup to 7 or 8 metres and to be raised to a height of up to 5 metres.The machine body is in two halves which are bolted together. It is made in very thick sheet steel with ribbingreinforcements to guarantee its non-deformability even when subjected to extremely high internal pressure.Material loading and liquid separation are carried out at the rear of the machine, where the ram housing is alsosituated. The final dehydration of the waste by means of the compacting ram and the counterpressure supplied bythe adjustable hatch that allows the material to exit along a channel, is carried out at the front of the machine.There are three versions of the ECOCOMPACT which vary in compacting capabilities, compression values andproduction levels, as shown in the table below. All models are build in sheet steel and hot-galvanised carbon steelor in AISI 304L and 316L stainless steel.The equipment is supplied complete with an hydraulic oil pump unit with two motors and two pumps for theindependent supply of the compacting and counterpressure circuits.A control panel with all the electrical equipment required to operate the motors is supplied with a PLC and keyboardfor the management of the programmed work cycles.
PRINCIPIO DI FUNZIONAMENTOCARATTERISTICHE TECNICHE
Start of Ecocompact ramming operationTechnical Characteristics