1371374-A02-A July 2019
INSTALLATION INSTRUCTIONS
SHOWER
Engle�eld
VALENCIA ELITE
Englefield has a history of making superb showers and their popularity is testament to their quality and affordability.
It’s the details that Englefield cares about - from pioneer-ing the latest technology, to innovative design, it’s all to make your showering experience the very best it can be.
Corner Sliding 12x9
Page 1
Before installing the shower please read these instructions carefully to familiariseyourself with the required tools, materials and installation sequences. Please leave theseinstructions for the consumer after installation. Refer to the separate care and maintenanceguide for important care and cleaning information.
Ensure that the shower tray and wall, if applicable, are completely finished prior toinstalling your shower door and return. Follow all warnings, cautions and instructionscontained in this guide.
1. ENGLEFIELD strongly recommends that a minimum of TWO persons install this enclosure due to the weight of the door panels. 2. Toughened safety glass cannot be cut. Risk of injury or product damage.
3. Wear protective footwear when lifting panels.
4. Wear safety glasses when drilling.
1. The wall retainers must be installed onto a waterproof, vertical and flat wall surface. Failure to do so will result in an unsatisfactory seal, which may cause property damage. The wall inclination (out of squareness) is recommended to be out by no more than +/- 4mm/m. 2. Please install this door onto an ENGLEFIELD Quick - Fit Low Profile shower tray only, unless installing directly onto tiled walls and floor.
®
3. Care must be taken when drilling into walls and floors to avoid any hidden pipes or
wires.
4. It is the responsibility of the INSTALLER to ensure that the installation complies with council and or local authority bylaws.
INSTALLATION INSTRUCTIONSVALENCIA ELITE
BEFORE YOU BEGIN
SAFETY !
! ATTENTION
Instructions, drawings, and diagrams contained in this manual present information available at the time of printing.
changes without further notice.
ENGLEFIELD
Corner Sliding Shower
Page 2
INSTALLATION INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED
PARTS IDENTIFICATION
ENGLEFIELD
3.0 mm2.0 mm - supplied
#1Square
Drive
2 x WallChannels
1 x Door
1 x Door Frame
1 x Seal Pack 2 x Corner
Covers
2 x WallFinishing Strips
VALENCIA ELITE Corner Sliding Shower
4 x RollerCovers
8 x Fixing Screws
8 x Assembly Screws
2 x Cover Caps
2 x Cover Caps
B
A
1 x Handle Assembly
1 x Hex Key
1 x Fittings Kit
1 x Handle Kit
Page 3
INSTALLATION INSTRUCTIONS
ENGLEFIELD
1 x Drip Strip Extrusion
1 x Side Panel
4 x Assembly Screws
2 x Top Caps
1 x Top Cap
1 x Screw Spacer
4 x Cover Caps
C
VALENCIA ELITE Corner Sliding Shower
CONSTRUCTION REQUIREMENTS
Due to the weight of the glass panels Englefield strongly recommendsconstructing double studs (as below) to fix the wall retainers to.
!ATTENTION
Page 4
INSTALLATION INSTRUCTIONS
A
Double studsDouble
studs
B
Size Dim ‘A’
1200 x 900 LH 1200
900
Dim ‘B’
900
1200
ENGLEFIELD
1200 x 900 RH
VALENCIA ELITE Corner Sliding Shower
2005mmMinimumHeight
INSTALLATION - Options
Page 5
INSTALLATION INSTRUCTIONS
ENGLEFIELD
Tray: For tray installation refer to the instructions supplied with the tray.
Wall: For wall installation refer to the instructions supplied with the wall.
- Proceed to Door and Return Installation.
- The door and return can be installed directly onto the wall and floor tiles.
- Proceed to Door and Return Installation.
OPTION 1 - Acrylic Wall & Tray
OPTION 2 - Tiled Wall & Acrylic Tray
OPTION 3 - Tiled Wall & Floor
Tray: For tray installation please refer to the instructions supplied with the tray.
Wall:- The vertical wall retainers MUST be installed onto the waterproof membrane PRIOR TO WALL TILING. If possible the complete door system should be installed onto the waterproof membrane prior to wall tiling.
CAUTION: Failure to install the wall retainers first may mean the door system may not fit on the shower tray due to the tile thickness.
- If not installing the complete door system prior to tiling, install the wall retainers and tiles. The retainer cover extrusion can be inserted after tiling - there is no need to leave a tiling gap. Refer to image.
- Proceed to Door and return installation.
Tile up toretainer
VALENCIA ELITE Corner Sliding Shower
± 0 mm ± 0 mm
Caution: Ensure tray or tiled floor is
For tray base option: - Mark 10mm in from top edge of tray.
For tiled base option: - Mark from finished wall to outer edge of retainer.
Tip: Cover the waste to prevent the loss of small parts. If installing onto a tray protect the tray surface during installation.
Page 5
10 mm
10 mm
1200 x 900 LH1200 x 900 RH
1175 875 875 1175
ASize B
Page 6
INSTALLATION INSTRUCTIONS
ENGLEFIELD
INSTALLATION
1
B
A
(a) Mark the locations of the wall retainers.
level & walls are vertical & square.
VALENCIA ELITE Corner Sliding Shower
Page 7
INSTALLATION INSTRUCTIONS
ENGLEFIELD
(a)
Position the wall channels on the wall. The short leg should face inside the showerenclosure. Using a level, ensure that the channels are upright.
Mark the position of the fixing holes down the centre of the channels, then remove the wall channels. Note! The wall channel is not fitted at this stage.
Drill with a 3mm bit. For other types of wall structure, alternative fixings may berequired (not supplied).
(b)
(c)
Apply silicone sealant along the length of the wall and at the bottom where the wallchannel will be placed, including the top of the tray.
(d)
Position the wall channels on the wall and install the fixing screws .(e)
Fully tighten the fixing screws, making sure that the wall channels are upright.(f)
2
10 mm
± 0 mm
3 mm
x4
x4
A
A
VALENCIA ELITE Corner Sliding Shower
Page 8
INSTALLATION INSTRUCTIONS
ENGLEFIELD
replace the top roller assembliesTo switch the door orientation,
with the bottom roller assemblies.Note! The roller assemblies with the push button will be at the bottom.
Door
(a) The sliding door can be either a LH or RH opening. To change the opening simplyrotate the frame through 180º before continuing with the installation.Note! If you rotate the frame, then you will need to rotate the door so that thehandle holes are in the correct position. You may also need to swap the rollerassemblies around (the rollers with screw adjustment need to be at the top).
3Logo badge onoutside of shower
Long legto outside
RH LH
VALENCIA ELITE Corner Sliding Shower
Sliding Door
Side Panel
Page 9
INSTALLATION INSTRUCTIONS
ENGLEFIELD
STUDIO GLIDE Alcove Sliding and side panel
4
Sliding Door
Side Panel
Page 9
INSTALLATION INSTRUCTIONS
ENGLEFIELD
(a)
(a)
The door orientation denotes the direction of the side panel. Once the door is in itscorrect orientation, fit the drip strip extrusion to the bottom edge of the side panel.Gently tap extrusion into place with a rubber mallet.
(b)
(b)
(c)
(c)
(d)
(d)
(d)
Fit the corner posts together, ensuring that the door and side panel engage correctly.
Install the side panel into the other wall channel.
Install the door frame into the wall channel.
VALENCIA ELITE Corner Sliding Shower
Page 10
INSTALLATION INSTRUCTIONS
ENGLEFIELD
5
Ø 3 mm
x4
± 0 mm
(a)
(a)
From the inside of the enclosure, drill four holes in the door frame through the centre marked points on the wall channel with a 3 mm HSS drill (not supplied).
If frame adjustment is required, keep corner post assembly fitted tightly togetherand carefully slide the frame (door and/or side panel) out from the wall channels.
(b)
Install and tighten the wall channel assembly screws . (c)
Repeat the process for the other wall channel.(d) Fit the corner covers to the wall channels. They should ‘snap’ into place.
B
B
Sliding Door
Side Panel
Sliding Door
Side Panel
(e)
VALENCIA ELITE Corner Sliding Shower
(a)
(b)
Use the Screw Spacer to install screws into the four corner post holes, then tighten.The Screw Spacer is to help prevent losing screws within the corner post assembly.
Fit the screw cover caps over the screwheads.
Page 11
INSTALLATION INSTRUCTIONS
ENGLEFIELD
6
C
C
VALENCIA ELITE Corner Sliding Shower
Page 12
INSTALLATION INSTRUCTIONS
ENGLEFIELD
7
(a) Hang the door onto the top rail.
Note! Make sure that the top rollers have adjusting screws facing downwards.
(b)
Loosen the top rollers with the adjusting screw until the bottom rollers easily clip intothe bottom rail.
(c)
Finally, tighten the roller adjustment to give an even, smooth action when the door isopened and closed.
VALENCIA ELITE Corner Sliding Shower
Page 13
INSTALLATION INSTRUCTIONS
ENGLEFIELD
8
(a) Install the door handle, ensuring the grub screws are on the underside.
(b)
(c) Lock the top roller assemblies in position by turning the lock through 90º.
(d) Fit the roller covers.
Fit the seals to the door and the fixed panel.
Rotate 90° UnlockedLocked
VALENCIA ELITE Corner Sliding Shower
Page 14
INSTALLATION INSTRUCTIONS
ENGLEFIELD
9
(a)Apply sealant along the outside surfaces of the enclosure.
Install the wall finishing strips, if desired.
(b)
Allow the silicone sealant to cure for 24 hours before use.
(c)
Fit the caps to the top of the extrusions. Add silicone or modify caps to fit if required.
(d)
VALENCIA ELITE Corner Sliding Shower
Full length
200mm up
Full length
200mm up
Full length
Full length
wall
retainerchannelsilicone/adhesive
wallliner
finishingstrip
- Installation complete -
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND KOHLER NZ LTDFree Ph: 0800 100 382Free Fax: 0800 664 488www.englefield.co.nz
AUSTRALIA KOHLER AUSTRALIA
Free Ph: 1 800 ENGLEFIELD (1 800 364 533)www.englefield.com
Engle�eld
INSTALLATION INSTRUCTIONS
CLEANING AND MAINTENANCE INSTRUCTIONS
For warranty information, please visit our website.
Please refer to the homeowners guide and our website for cleaning instructions.
SPARE PARTS
Seal (fixed panel)
1382132
Seal (door)
1382133
Retainer Cover1278348-**
Wall Finishing Strip1315530-**
Side Panel Bottom Strip1348296-**
Top Roller1260199-**
Bottom Roller1260200-**
Side Panel Fittings Kit1348297-**
Magnetic Seal1260196
Wall Channel1278347-**
** Colour code must be specified when ordering
Door (glass only)1348294
Door Frame1348293-**
Fittings Kit1348295-**
Handle Assembly1365840-**
Glass Aftercare Kit98945A-NA
VALENCIA ELITE Corner Sliding Shower
Scan the QR barcode on the packaging or underside of top caps to identify the product SKU and date of manufacture.!