![Page 1: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/1.jpg)
Detailed pictures of the construction of a rocket mass heaterBy josh , rocket mass heater at Organizmo, colombia
Not me in picture and not at Organizmo.It is another rocket project in colombia that i am invovled in though ;-)
![Page 2: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/2.jpg)
Preparing the areaFirst there is of plastic (pvc or similar) as a moister barrier. After that a layer of gravel a laid fairly level. On top of the gravel i poured a thin layer of watery concrete with gravel
on top of everything and maintaining the level. Big rocks are layed on the border with concrete to hold them in place.
This is all done to protect the cob and stove from moister from below and also raising It a bit off the ground.
![Page 3: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/3.jpg)
Laying a base for the bench
A course of bricks in concrete because bricks is what i had, could be anything
sturdy enough,It is just to raise the bench from the ground.
![Page 4: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/4.jpg)
Since there are no connections for these pipes i used scraps of metal and chicken mesh covered in
cement/cob mortar. (no- straw cob)
Laying out the flues these are ceramic pipesMost common here is smoke ducts, they are usually quite coslty and these were a good
dimension a about 8 inches.These pipes determined the dimensions for the
rest of the stove.
![Page 5: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/5.jpg)
Construction of the combustion unit
![Page 6: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/6.jpg)
Used in total about 50 bricks
![Page 7: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/7.jpg)
first course of bricks : make sure it is wide enough for the courses of bricks and for the bricks that will hold the a barrel which you will see
soon. the hole you see is a ash pit.
base layer
![Page 8: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/8.jpg)
these bricks are layed flat, this layer will determin the length of the burntunnel. Need to measure this before hand beacuase the bricks can be different.
Layer 1
![Page 9: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/9.jpg)
Layer 2
This layer the bricks are stacked on edge, around the entire layer beneath.
![Page 10: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/10.jpg)
On this level i had to cut off one third of two bricks to maker It work. Now it is ready for the
heat riser!
Layer 3
![Page 11: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/11.jpg)
Creating the support for the barrel and directing the gases to the pipes. I find
it easiest and strongest to do with bricks. It can be done with rock ,cob, or
a combination of everything.
Can you see what is wrong with the picture above? No? Well the bricks should be locked together like puzzle pieces. Ana-maria from organizmo reminded me! Bricks stacked straight on eachother will flop over.
Creating barrel support and the "bridge" to the pipes.
![Page 12: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/12.jpg)
Now the bricks are stacked properly and mortared together with sand/clay. You can see the bridge to the pipes being created.the Hole there is going to be the cleanout.
![Page 13: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/13.jpg)
The bricks are plastered in and out, smoothed out And the bridge is made wire mesh and cobbed up.
This inuslation method is not reccomended and is experimental. The heatriser is ceramic tubing, the insulation is a charcoal mix with wet clay and put In a chicken wire cylinder. Other tested insulation methods are advised. It is what was available...
Heatriser and insulation in place!
![Page 14: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/14.jpg)
In-between hobbies include, Burning off paint from the barrel, mixing tons of cob (literally) and tincering with mini rocket
experiments.
![Page 15: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/15.jpg)
Putting up the barrel and giving her a test run! This gives you a final chance make adjustments like: putting the barrel at the desired height or the height which gives the best draft. Ok it works! Now what?
Test drive
![Page 16: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/16.jpg)
Sculpt a bench!
Ready for plaster!
![Page 17: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/17.jpg)
After testing a few batches here is the best i came up with:
plaster for top half
1 part clay2 part sand1 1/2 cow manure1 part flour pasteA few handfuls plant fiber ( fique)
Plasters
![Page 18: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/18.jpg)
Platster for bottom half
1 part clay2 parts clay
1 part clay soil1 part rice husks
![Page 19: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/19.jpg)
ready to go!
![Page 20: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/20.jpg)
![Page 21: Detailed pictures of the construction of a rocket mass heater](https://reader035.vdocuments.mx/reader035/viewer/2022062520/56816149550346895dd0c68d/html5/thumbnails/21.jpg)
This slide is ment to assist you if you are thinking of creating a rocket stove, or just as inspiration. It is not a detailed description it merely shows the main steps through pictures. If you search the web for rocket mass heater you will find the dimensions you need for your stove. I highly reccomend reading the book about rocket mass heaters.Alright! Hope you are making one right now! If not and you want to, send me an email and i can hopefully help you out! I am willing to come hold a rocket mass heater workshop with you as well!
Thank you all at Organizmo for the help and support with the creation of this stove!
http://organizmo.org/
Joshua Roxendal [email protected]
Http://pemakultur.ihop.nu