Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 1
DEPARTMENT OF ELECTRONICS
2017-18
GOVERNMENT COLLEGE [A]
RAJAMAHENDRAVARAM
BOARD OF STUDIES MEETING
06 NOVEMBER 2017
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 2
GOVERNMENT COLLEGE (AUTONOMOUS):: RAJAMAHENDRAVARAM
The Board of studies meeting of DEPARTMENT OF ELECTRONNICS was convened at 11.30 A.M on 06-11-2017 under
the Chairmanship of Sri P.V.SATYAJI, In-charge of the department. The members present Discussed various aspects
such as changes to be made in the Syllabi, Scheme of Evaluation and Blue print of third year(VIth semester) B.Sc.,
Electronics course, both for theory and practical's for introducing and implementing them during the academic year
2017-18 onwards. The following members were present.
S.No Name Designation Signature
1
Sri P.V.SATYAJI
Lecturer in charge
Department of ELECTRONICS
Government College(A)
Rajamahendravaram
Chairman
2
Ln.Esub Basha Sheik
Dr.P.V.S.S.S.N. Reddy
Sri N. VenkannaBabu
Members
(Faculty members of the
Department)
3 Sri D. Gangadharudu,
Lecturer,
SRVBSJBMR College, Peddapuram
Subject expert
4 Sri C. Satyanarayana,
SKVT College,
Rajamahendravaram
Subject expert
5 Dr. K. Venkateswaralu,
Sri Y.N. College [A], Narsapur University Nominee
6
Sri Bala Krishna
D.E, Polavaram Project.
Expert from
Industry
7 Sri Y. Durga Prasad,
MSc (Electronics),
Andhra University
Alumni
GOVERNMENT COLLEGE (AUTONOMOUS):: RAJAMAHENDRAVARAM
( Re-Accredited by NAAC with grade “A”)
DEPARTMENT OF ELECTRONICS
BOARD OF STUDIES MEETING: 06 NOVEMBER 2017
BOARD OF STUDIES MEETING: 07 APRIL 2017
BOS MEMBERS: 2017-18
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 3
The following documents are submitted to the Academic Coordinator and Controller of Examinations.
1. Resolutions of Board of Studies Meeting 2. Syllabi II,IV & VI semester 3. Blue print and model question paper for both theory and Practical Examinations 4. Revised Examiners list 5. Any other new proposals
Date: 06 December 2017
Chairman
Board of Studies
Department of Electronics
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 4
GOVERNMENT COLLEGE (AUTONOMOUS): RAJAHMUNDRY
(Re-Accredited by NAAC with grade “A”)
DEPARTMENT OF ELECTRONICS
BOARD OF STUDIES MEETING ON 06 November 2017
RESOLUTIONS:
1. It is resolved to approve the introduction of APSCHE recommended Choice Based Credit System [CBCS] to the
II B.Sc., course from the academic year 2017-18. CBC system was implemented for the I B.Sc., course during the
academic year 2016-17.
2. It is resolved to approve the syllabus designed under autonomy setup for III and IV Semesters of II B.Sc.,
considering the syllabus recommended by APSCHE, ANUR, local needs of Industry and students for the academic
year 2017-18.
3. It is resolved to approve the prescribed books for the syllabus designed above.
4. It is resolved to assess the student’s performance under Continuous Internal Assessment (CIA) and Semester End
Examination (SEE) components at 40:60 ratio for the II B.Sc., course from the academic year 2017 -18 as was
done for I BSc course in the academic year 2016-17.
5. It is resolved to approve the Scheme of Examination and Blue print of Semester End Examination (SEE) for III and
IV Semesters of II B.Sc., from the academic year 2017-18.
SCHEME FOR SEMESTER END THEORY EXAMINATION (SEE):
TYPE OF QUESTION MARKS SCHEME
PART-A
Essay Questions Each question
carries 8 Marks
4x8 = 32 M
Answer all questions
1. (A) & (B) - From Unit I 2. (A) & (B) – From Unit II 3. (A) & (B) - From Unit III 4. (A) from Unit IV and
(B) from Unit V
PART-B
Short Answer
Questions
Each question
carries 4 Marks
5x4= 20 M
Answer any 5 out of 8 questions
5
6 4 Theoretical Questions
7 Not more than one question from any
8 each unit.
9
10 4 Numerical Questions
11 Not more than one question
12 from any/each unit.
At least one theoretical/numerical to be
asked from each unit
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 5
SCHEME FOR INTERNAL & EXTERNAL PRACTICAL EXAMINATION:
**Award of marks for number of practicals recorded in the Record
06 PRACTICALS - 10
05 PRACTICALS - 08
04 PRACTICALS - 06
03 PRACTICALS - 04
LESS THAN 03 - 00
PART-C
Very Short Answer
Questions
Each question
carries 2 Marks
4x2 = 8 M
Answer any four questions
13
14 Not more than one question
15 from each unit
16
17
S.No Description Marks
1 Formula 05
2 Tabular Form & Readings 10
3 Calculations & Result
(Including Graph)
15
4 Precautions & Units 05
5 Viva Voce 05
6 Record** 10
7 TOTAL 50
INTERNAL : 50 M
EXTERNAL : 50 M
TOTAL: 100 M
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 6
6. It is resolved to continue to offer two elective papers in semester VI for III B.Sc., and two cluster elective papers
A & B instead of paper IV for the academic year 2017-18 also so as to enable the student to choose one of the
two.
3rd YEAR
VI SEMESTER
PAPER-VII ELECTIVE (Choose A or B)
A: MICROPROCESSOR 8085
Practical
B: RADAR SYSTEMS & SATELLITE COMMUNICATION
Practical
Paper VIII Cluster Elective A
A1: EMBEDDED SYSTEMS AND APPLICATIONS
Practical A2: ELECTRONICS COMMUNICATION
Practical A3: ADAVANCED DIGITAL SYSTEM
Practical
Cluster Elective (B)
B1:POWER ELECTRONICS Practical B2: APPLIED MATHEMATICS
Practical B3: ANALOG AND DIGITAL I/C APPLICATIONS
Practical
Justification to the inclusion of the paper "RADAR SYSTEMS & SATELLITE COMMUNICATION ":
Objective:
To provide the specialized multidisciplinary skills required for careers in the satellite and space industries.
Importance of Radar systems & Satellite Communication:
Applicable to radio frequency (RF) and microwave engineering useful in Satellite Communications
In Meteorological satellite receiving stations for the live reception of satellite weather images.
Engineering problem solving - be able to analyse problems within the field of mobile and satellite communications
and more broadly in electronic engineering and find solutions
Understand Antennas and Propagation of radio waves
Decipher Principles of Telecommunications & Packet Networks
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 7
Career opportunities:
Design engineers
Communications Engineer
Satellite Operation Engineer
Satellite Program engineers:
Software Developers
Defence contractors
Communication technician
Application orientation:
Radio frequency identification (RFID), broadcasting, satellite links, microwave ovens, printed and
integrated microwave circuits, mobile communications, satellite communications, nanotechnology or
for integration with optical communications
Research Opportunities:
Research could be carried out in the Advanced broadcasting Technology Institutes and the Institutes
for Communication Systems.
7. It is resolved to continue the examination pattern for the III year students same as that followed during the year
2015-16.
8. It is resolved to continue the scheme of paper setting for theory examinations for V and VI semester for a
maximum of 75 marks for external and remaining 25 marks for internal assessment
9. It is resolved to continue the scheme of evaluation for practical examination for V and VI semester for a
maximum of 75 marks for external and 25 marks for internal.
10. It is resolved to approve the revised list of examiners and paper setters for the academic year 2017-18. List
annexed.
Date: 06 December 2017 Chairman
Board of Studies
Department of Electronics
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 8
GOVERNMENT COLLEGE (A) : RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
SYLLABUS FOR I B.Sc., ELECTRONICS
MODULE-II [ELECTRONIC DEVICES & CIRCUITS]
SEMESTER II
(As Approved in the BOS meeting held on 06 November 2017 for 2017-18)
UNIT- I
JUNCTION DIODES: (12 hrs)
Basic principles of Semiconductor materials – classification – energy bands in solids – P and N type
semiconductor materials – energy band diagrams. PN junction diode - P-N junction theory-depletion region, barrier
potential, working in forward & reverse bias condition, Junction capacitance, Diode current equation (no derivation),
Effect of temperature on reverse saturation current, V-I Characteristics, Zener and Avalanche Break down, Zener
diode – Construction, Working and V-I characteristics, Voltage regulator using Zener diode - Tunnel diode and
varactor Diode - Working & Applications.
UNIT- II
BIPOLAR JUNCTION TRANSISTORS (BJT): (18 hrs)
PNP and NPN transistors, current components in BJT, BJT static characteristics (Input and Output), Early
effect, CB, CE,CC Configurations (Cut-off, Active and saturation regions), h-parameters, h-parameter equivalent
circuit, CE configuration as two port network, The CE amplifier analysis and parameters. Thermal runaway, concept
of stability and Stability factor – factors affecting stability. Biasing and Load line analysis – fixed bias and voltage
divider biasarrangements, Transistor as a switch.
UNIT - III
FIELD EFFECT TRANSlSTOR & UJT: (12 hrs)
FET - Construction - Working – Drain &Transfer characteristics -Parameters of FET – FET as an amplifier.
MOSFET- Enhancement MOSFET –Depletion MOSFET – Construction & Working and drain characteristics-
Comparison of FET & BJT. UJT Construction-working, V-I Characteristics, Applications. Small signal FET models.
UNIT – IV
PHOTO ELECTRIC DEVICES: (6 hrs)
Structure and operation, characteristics and applications of LDR, Photo Voltaic cell, Photo diode.
LED and LCD. Silicon controlled rectifier (SCR) – construction, working and V- I characteristics, CRO – construction,
working and applications.
UNIT - V
POWER SUPPLIES: (12 hrs)
Rectifiers - Half wave, full wave and bridge rectifiers - Efficiency - Ripple factor – Regulation. Types of filters- Shunt capacitor, L-Section and π Section filters and their working (no derivations) -Three terminal fixed voltage I.C regulators (78XX and 79XX) - Principle and working of switch mode power supplies (SMPS).
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 9
TEXTBOOKS:
1. Electronic Devices and Circuits David A.Bell, Fifth edition. Oxford university press
2. A.P Malvino, "Principles of Electronics", TMH, 7th edition
3. T.F. Bogart, Beasley, "Electronic Devices and circuits", Pearson Education, 6th Edition
4. N.N. Bhargava, D.C Kulshreshta, and S.C Gupta,"Basic Electronics and Linear Circuits'' TMH
5. T.L.Floyd, "Electronic Devices and circuits", PHI, fifth edition
6. V.K. Metha, "Principle of Electronics", S CHAND Co. New edition
7. Godse A.P., Bakshi U.A (1st edition), Electronics Devices, Technical Publications rune.
REFERENCE BOOKS:
I. Sedha R.S., A TextBook of Applied Electronics, S. Chand & Company Ltd.
2. Jacob Millman and Christos C. Halkias (2008) Integrated Electronics, Tara Mcgraw-Hill
3. Robert L. Boylestad, Louis Nashelsky (10th edition). Electron
4. Devices and Circuit Theory, Dorling Kindersley (India Pvt. Ltd.)
5. Unified Electronics (Circuit analysis and electronic devices) by Agarwal-Arora.
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 10
GOVERNMENT COLLEGE (A): RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
TOPICS INCLUDED UNDER AUTONOMOUS SET UP
CLASS : I B.Sc.,
SEMESTER : II
PAPER : I
TITLE OF THE PAPER : ELECTRONIC DEVICES & CIRCUITS
ADDITIONAL TOPICS JUSTIFICATION
1. Basic principles of Semiconductor materials – classification
2. Eenergy bands in solids – P and N type semiconductor materials – energy band diagrams.
3. Small signal FET models.
1. Distinguish and identify types of solids with respect to the ability to flow of current
2. Analyze the classification of materials on the basis of conductivity
3. To understand the effect of electric field, and charge carriers on the flow of electricity
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 11
GOVERNMENT COLLEGE (A): RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
ELECTRONICS PAPER -1
(ELECTRONIC DEVICES & CIRCUITS)
(As Approved in the BOS meeting held on 06 November 2017 for 2017-2018)
MODEL OF SEMESTER END EXAMINATION QUESTION PAPER [THEORY]
SECTION DESCRIPTION MARKS
A Essay type questions- Four questions to be
asked with internal choice in each
question (A or B) from each unit.
Student has to answer four questions
choosing one (A or B) from each question.
Each question carries 8 marks.
4x8 =32
B Short answer type questions - Eight
questions are to be asked (5 theory + 3
numerical). Student has to answer any five
questions. Each question carries 4 marks
5x4 = 20
C Very short answer type questions - Five
questions are to be asked at least one from
each unit. Student has to answer any four
questions. Each question carries 2 Marks
4x2 =08
TOTAL MARKS 60
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 12
GOVERNMENT COLLEGE (A): RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
BLUE PRINT FOR II - SEMESTER END EXAMINATION
MODULE – II: ELECTRONIC DEVICES & CIRCUITS
Time: 3 Hours Max. Marks: 60
TYPE OF QUESTION MARKS SCHEME
PART-A
Essay Questions
(Internal Choice)
Each question carries
8 Marks
4x8 = 32 M
Answer all questions
1. (A) & (B) - From Unit I 2. (A) & (B) – From Unit II 3. (A) & (B) - From Unit III 4. (A) from Unit IV and
(B) from Unit V
PART-B
Short Answer
Questions
Each question carries
4 Marks
5x4= 20 M
Answer any 5 out of 8 questions
5
6 4 Theoretical Questions
7 Not more than one question from
8 each/any unit.
9
10 4 Numerical Questions
11 Not more than one question
12 from each/any unit.
At least one theoretical/numerical to be asked
from each/any unit
PART-C
Very Short Answer
Questions
Each question carries
2 Marks
4x2 = 8 M
Answer any four questions
13
14 Not more than one question
15 from each / any unit
16
17
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 13
GOVERNMENT COLLEGE (A) : RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
PRACTICAL MODULE -1 (I B.Sc.,)
(ELECTRONIC DEVICES & CIRCUITS LAB)
LIST OF EXPERIMENTS
(As Approved in the BOS meeting held on 06 November 2017 for 2017-18)
Work load: 30 hrs per semester 2 hrs/week
LIST OF EXPERIMENTS
(Any Six Experiments should be done)
1. V-I Characteristics of Junction Diode.
2. V-I Characteristics of Zener Diode.
3. Regulated Power Supply using Zener Diode.
4. IC Regulated Power Supply (78XX)
5. BJT input and output Characteristics (CE Configuration) and determination of h-parameters.
6. Characteristics of UJT and determination of its parameters.
7. Characteristics of JFET and determination of its parameters.
8. LDR characteristics
9. Characteristics of L and π section filters using full wave rectifier.
LAB MANUALS
1. Zbar, Malvino and Miller, Basic Electronics, A Text Lab Manual, Tata McGraw Hill.
2. Sugaraj Samuel R., Horsley Solomon, B.E.S. Practicals.
GOVERNMENT COLLEGE (A):: RAJAMAHENDRAVARAM
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 14
DEPARTMENT OF ELECTRONICFS
SYLLABUS FOR II B.Sc., ELECTRONICS
MODULE-IV [ANALOG AND DIGITAL IC-APPLICATIONS]
SEMESTER IV
(As Approved in the BOS meeting held on 06th November 2017 for 2017-18)
Unit – I (10hrs)
OPERATIONAL AMPLIFIERS: Definition, Basic op-amp Ideal op-amp, Block diagram of op-amp,
inverting, noninverting, virtualground, Adders, subtractors, summing amplifier, voltage follower, op-amp
parameters, voltage to current convertor ,integrator, differentiator, differential amplifier, Logarithmic
amplifier.
Unit- II (15 hrs)
OP-AMP CIRCUITS: voltage regulator, comparator ,zerocross detecting circuit, instrumentation amplifier,
multivibrators-astable, monostable, Bi-stable, Schmitt trigger. sine wave generator, square wave generator,
triangular wave generator, Active filters(Basics)-low pass, high pass, band pass filters
IC-555 –functional block diagram and mention it’s applications
Unit-III (15hrs):
COMBINATIONAL & SEQUENTIAL LOGIC CIRCUITS (IC-Applications): Design of Code convertor: BCD to Seven Segment ,BCD to Grey, Grey to Binary.
Design of Counters using State Machine: Mod N counter, Preset Table,Binary Up/Down
Counter. Design of Universal Shift Register
UNIT-IV (10hrs)
DATA CONVERTERS: A/D converter:- Successive Approximation ADC,-Single slope and dual slope converter, Sigma-delta ADC,
D/A converter: R-2R Ladder network, Binary Weighted .
UNIT-V (10hrs)
DIGITAL SYSTEM INTERFACING AND APPLICATIONS: interfacing of LED’s Applications of Shift Registers: Serial-in-Serial –out, Serial-in-Parllel-out, Parllel-in-Serial –out, Parllel -in- Parllel –
out Shift Registers,
TEXT BOOKS:
1. G.K.Kharate-Digital electronics-oxford university press
2. M.Morris Mano, “ Digital Design “ 3rd Edition, PHI, New Delhi.
3. Op Amp and Linear Integrated Circuits By Ramakant Gaykwad
4. Linear Integrated Circuits By Roy Choudary
Reference Books :
1. Jacob Millan ,Micro Electronics,McGraw Hill.
2. Mithal G K, Electronic Devices and Circuits Thana Publishers.
3. Allan Motter shead ,Electronic Devices and Circuits – An Introduction- Prentice Hall
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 15
GOVERNMENT COLLEGE (A): RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
TOPICS INCLUDED UNDER AUTONOMOUS SET UP
CLASS : II B.Sc.,
SEMESTER : IV
PAPER : II
TITLE OF THE PAPER : ANALOG AND DIGITAL IC-APPLICATIONS
Topics included Justification
Frequency counter
Applications of Shift Registers:
Serial-in-Serial –out
Parallel -in- Parallel –out
To understand the measurement of frequency digitally
To electronically control the movement of bits/ data in different modes
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 16
Government College (A) :: RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS MODULE IV :: SEMESTER IV ( PAPER II)
ANALOG AND DIGITAL IC-APPLICATIONS
MODEL OF SEMESTER END EXAMINATION QUESTION PAPER [THEORY]
SECTION DESCRIPTION MARKS
PART-A
Essay Questions
(Internal Choice)
Essay type questions- Four questions to be
asked with internal choice in each
question (A or B) from each unit.
Student has to answer four questions
choosing one (A or B) from each question.
Each question carries 8 marks.
4x8 =32
PART-B
Short Answer
Questions
Short answer type questions - Eight
questions are to be asked (5 theory + 3
numerical).
Student has to answer any five questions.
Each question carries 4 marks
5x4 = 20
PART-C
Very Short Answer
Questions
Very short answer type questions - Five
questions are to be asked at least one from
each unit.
Student has to answer any four questions.
Each question carries 2 Marks
4x2 =08
TOTAL MARKS 60
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 17
GOVERNMENT COLLEGE (A): RAJAMAHENDRAVARAM
DEPARTMENT OF PHYSICS
BLUE PRINT FOR IV - SEMESTER END EXAMINATION
MODULE – IV: ANALOG AND DIGITAL IC-APPLICATIONS
Time: 3 Hours Max. Marks: 60
Marks Pattern Type of Question
PART-A (4x8
= 32 M)
Answer all questions
1. (A) & (B) - From Unit I 2. (A) & (B) – From Unit II 3. (A) & (B) - From Unit III 4. (A) from Unit IV and
(B) from Unit V
Essay Questions
PART-B (5x4=
20 M)
Answer any 5 out of 8 questions
5
6
7 5 Theoretical Questions
8 one question from each / any unit.
9
10
11 3 Numerical Questions
12 Not more than one question
from each/any unit.
Short Answer
Questions
PART-C
(4x2 = 8 M)
Answer all questions
13
14
15 Not more than one question
16 from any unit
17
Very Short
Answer Questions
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 18
GOVERNMENT COLLEGE (A):: RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
PRACTICAL MODULE – II ( II B.Sc.,)
(ANALOG AND DIGITAL IC-APPLICATIONS)
LIST OF EXPERIMENTS
Work load: 30 hrs per semester 2 hrs/week
1. Op-Amp as inverting and non-inverting
2. Op-Amp as integrator and differentiator
3. Op-Amp as adder & subtractor
4. Op-Amp as voltage to current converter
5. Op-Amp as sine wave generator (Wien bridge oscillator)
6. Op-Amp as sine wave generator
7. Astable multivibrator determination of frequency (using IC-555)
8. Schmitt trigger using IC-555 timer
Lab experiments are to be done on breadboard and simulation software (using multi
sim) and output values are to be compared and justified for variation.
_______________
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 19
Government College (A): Rajamahendravaram
DEPARTMENT OF ELECTRONICS B.Sc III Year - Electronics
PAPER – III Microprocessor 8085
UNIT-I (12Hr)
Introduction to Microcomputer and Microprocessor: Intel 8085 Microprocessor Block diagram – central processing
unit CPU – arithmetic and logic unit ALU – timing and control unit – register organization – address, data and control
buses- pin configuration of 8085 and its description.
UNIT-II(18Hr)
Instruction cycle, machine cycle, fetch and execute cycles. Timing diagrams ,Stack and subroutines .Interrupts –
structure -hardware and software interrupts – maskable and non-maskable interrupts (basics only)
UNIT-III (18Hr)
Instruction set of 8085: addressing modes -instruction and data formats- classification of instructions. Assembly
language programming examples of 8 and 16 bit addition, subtraction, multiplication and division. Finding the largest
and smallest in a data array. Programming examples
UNIT-IV(12Hr)
Interfacing peripherals and applications: Architecture of 8251 (USART). Programmable peripheral interface (8255) -
D/A and A/D converters and their interfacing to the Microprocessor. seven segment LED.
Reference Books:
1. Microprocessor Architecture and Programming – Ramesh S. Goanker- Penram
2. Introduction to Microprocessor – Aditya. P. Mathur- TMH
3. Microprocessors and Microcontrollers Hardware and Interfacing- Mathivannan- PHI
4. Fundamentals of Microprocessors and Microcontrollers – B. Ram-DhanpatRai& Sons.
5. Advanced Microprocessor and Peripherals, Architecture, Programming and Interface- A.K.Ray and K.N.
Bhurchandi- TMH
6. Microprocessor Lab Premier- K.A. Krishna Murthy
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 20
GOVERNMENT COLLEGE (A): RAJAMAHENDRAVARAM
DEPARTMENT OF ELECTRONICS
SYLLABUS FOR III B.Sc., ELECTRONICS (w.e.f.2017-2018)
(As Approved in the BOS meeting held on 07 APRIL 2017 for 2017-2018)
PRACTICAL PAPER-III
Digital Electronics and Microprocessor Lab
1. Verification of truth tables of OR, AND, NOT, NAND, NOR, EX-OR gates (By using 7400-series)
2. Construction of gates using NAND, NOR gates.
3. Construction of Half and Full adders and verifying their truth tables.
4. Operation and verifying truth tables of flip- flops- RS, D, and JK using ICs.
5. Construction of Decade counters (7490).
6. Driving Stepper motor using JK flip-flop
7. Binary addition & subtraction. (8-bit & 16-bit)
8. Multiplication & division.
9. Picking up largest/smallest number.
10. Arranging –ascending/descending order.
11. Decimal addition (DAA) & Subtraction.
12. Time delay generation
13. Interfacing R-2R Ladder network (DAC) (4 bits) to generate waveforms.
14. Interfacing a stepper motor and rotating it clockwise/anti clockwise through a known angle.
Note: Students has to perform any 10 experiments
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 21
Government College (A), Rajamahendravaram
B.Sc III Year – Electronics
Paper – III Microprocessors 8085
Year End Examination (w.e.f. 2009-2010)
Scheme of Practical Examinations Practical examination question paper
Examination No. of
Marks Split up
Semester end
examination 75
Digital Electronics Microprocessors
Circuit - 15
Circuit construction-20
Tables – 20
Verification- 20
Program 30
Flow chart 15
Execution 30
Internal
examination 25
Circuit - 05 05
Construction - 10
Tables - 05
Verification - 05
Program 10
Flow chart 05
Execution 10
TOTAL 100
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 22
GOVERNMENT COLLEGE [A] :: RAJAMAHENDRAVARAM
DEPT.OF ELECTRONICS
ADVANCED ELECTIVE PAPER for
III B.Sc COURSE (w.e.f 2016-17)
Semester-v
ADVANCED ELECTIVE II: RADAR SYSTEMS & SATELLITE COMMUNICATION
Radar Systems:
Fundamental – A simple RADAR – overview of frequencies – Antenna gain Radar Equation – Accuracy and Resolution
– Integration time and the Doppler shift (Ch 1 of Text Book 1)
Designing a surveillance radar – Rader and surveillance – Antenna beam – width consideration – pulse repetition
frequency – unambiguous range and velocity – pulse length and sampling – radar cross section – clutter noise (Ch 2
of Text Book 1)
Tracking Radar – Sequential lobbing – conial scanning – Monopoles Radar – Tracking accuracy and Process –
Frequency Agility – Radar guidance
Satellite Communication
Satellite System – Historical development of satellites – communication satellite systems – communication satellites
– orbiting satellites – satellite frequency bands – satellite multiple access formats (Ch1 of Text Book 3).
Satellite orbits and inclination – Look angles, orbital perturbations, space craft and its subsystems – attitude and
orbit control system – Telemetry, Tracking and Command – Power system – Transponder – Reliability and space
qualification – launch vehicles (Ch2 & 3 of Text Book 4)
UNIT - IV
Multiple Access Techniques – Time division multiple access – Frequency division multiple access – Code division
multiple access – Space domain multiple access(Ch 7 of Text Book 4).
Earth Station technology – Subsystem of an earth station – Transmitter – Receiver Tracking and pointing – Small
earth station – different types of earth stations – Frequency coordination – Basic principles of special communication
satellites – INMARSAT VSAT, GPS, RADARSAT, INTELST
Text Books:
1. Understanding Radar Systems – Simon Kingsley and Shaun Quegan. 2. Introduction to Radar Systems – MI Skolnik 3. Satellite Communication – Robert M. Gagliardi 4. Satellite Communication – Manojit Mitra
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 23
SEMESTER-VI
CLUSTER ELECTIVE -A
A1: EMBEDED SYSTEMS AND APPLICATIONS
Work load: 60 hrs per semester 4 hrs/week
Unit – I (12hr)
Introduction to Embedded System
Embedded system overview,Design Challenge,processor technology, IC Technology, and design
Technology.
Unit – II (12hr)
Interfacing of peripherals to Microcontroller (8255)
Introduction 8255, pin diagram 8255, 8051 interfacing to 8255, Programming the 8255, control word
format,
Unit – III (18hr)
Serial communication: Basics of serial communication, 8051 connection to RS232, 8051 serial
communication Programming, modes and protocols, SBUF , Serial port control register, Doubling baud rate.
Unit – IV (18hr)
Applications of Embedded Systems: , Interfacing an ADC to the 8051,interfacing a DAC to the
8051,Interfacing to LED, Temperature measurement, sensors.
Reference Books:
1. The 8051 Microcontrollers and Embedded Systems – By Muhammad Ali Mazidi and Janice
GillispieMazidi- Pearson Education Asia, 4th Reprint, 2002
2. Microcontrollers – Theory and applications by Ajay V. Deshmukh-Tata McGraw-Hill
3. The 8051 Microcontroller - architecture, programming & applications By Kenneth J. Ayala- Penram International
Publishing, 1995
4. Programming and Customizing the 8051 Microcontroller – By MykePredko- TMH, 2003
5. Design with Microcontrollers By - J B Peatman- TMH.
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 24
DEPARTMENT OF ELECTRONICS
MODULE V :: SEMESTER VI ( PAPER CLUSTER-A1) EMBEDED SYSTEMS AND APPLICATIONS
SCHEME OF EVALUATION
Examination Marks Remarks
Semester end
examination 75
Internal
examination
25
Written examination : 10
Viva-voce : 5
Group Seminar : 5
Assignment : 5
PATTERN OF SEMESTER END THEORY EXAMINATION
Section Description Marks
A
Essay type questions-
Four questions are to be asked with
internal choice in each question ( Aor B).
One question from each unit.
Each question carries 10 Marks.
4x10 = 40
B
Short answer type questions - Eight
Two questions from each unit.
Student has to answer any 5 questions.
Each question carries 3 Marks.
5x3 = 15
C
Very Short answer type questions -
Ten questions are to be asked not more
than three questions from any unit .
Student has to answer ALL questions.
Each question carries 2 Marks.
10x2 = 20
TOTAL MARKS 75
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 25
SEMESTER-VI
CLUSTER ELECTIVE -A
A2: ELECTRONIC COMMUNICATIONS (60 HOURS)
Work load: 60 hrs per semester 4 hrs/week UNIT- I (12 hrs) BASICS OF COMMUNICATION SYSTEMS Block diagram of communication system. Types of Electronic Communication systems: Simplex, Duplex.
Analog /Digital Signals. Information theory analysis, channel capacity, coding
UNIT - II (15 hrs)
NOISE IN COMMUNICATION: External noise-Atmospheric, space noise, man-made noise, internal
noise- Thermal, Shot noise Definitions and relationship between Bit rate, Band rate, Bandwidth and signal to
Noise Ratio.
UNIT - III (18 hrs)
METHODS OF MODULATION Need for modulation. Amplitude modulation, Modulation index, frequency spectrum, generation of AM
(balanced modulator,), Amplitude Demodulation (diode detector), Frequency and phase modulation,
modulation index and frequency spectrum, equivalence between FM and PM, Generation of FM (Direct and
indirect methods), FM detector (Slope detector, balanced slope detector, PLL)
UNIT- IV (15 hrs) TRANSMITTERS& RECEIVERS Transmitters: Communication channels for AM and FM broadcast, AM transmitter: Lowlevel and high
level modulation, FM transmitter.
Receivers: Receiver parameters, sensitivity, selectivity and fidelity, Super Heterodynereceiver, AM
receivers, FM receivers. Frequency division multiplexing.
.
TEXTBOOKS 1. Electronic communication ,sanjeevagupta Krishna publishers.
2. H. Taub and D. Schilling, Principles of Communication Systems, Tata McGraw-Hill (1999)
3. W.Tomasi, Electronic Communication Systems: Fundamental through Advanced,
4. Pearson Education (2004)
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 26
REFERENCE BOOKS
1. S.Haykin, Communication Systems, Wiley India (2006)
2. G. Kennedy and B. Davis, Electronic communication systems, Tata McGraw Hill (1999)
3. R. P. Singh and S. D. Sapre, Communication Systems: Analog and Digital, Tata
McGraw Hill (2007)
4. L. E. Frenzel, Communication electronics: Principles and applications. Tata McGraw Hill (2002)
5. T.G. Thomas and S. Chandra Sekhar, Communication theory, Tata McGraw Hill (2006)
ELECTRONICS LAB -6(A)
ELECTRONIC COMMUNICATIONS LAB
Work load: 30 hrs per semester 2 hrs/week
(Any six experiments should be done)
1. Study of Amplitude Modulation and Demodulation. 2. Study of Frequency Modulation and Demodulation 3. Study of Pulse Amplitude Modulation 4. Study of Pulse Width Modulation 5. Study of Pulse Position Modulation 6. Study of Pulse Code Modulation 7. Simulation of AM modulation and Demodulation using software. 8. Simulation of FM modulation and Demodulation using software.
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 27
DEPARTMENT OF ELECTRONICS
MODULE V :: SEMESTER VI ( PAPER CLUSTER-A2) ELECTRONIC COMMUNICATIONS
SCHEME OF EVALUATION
Examination Marks Remarks
Semester end
examination 75
Internal
examination
25
Written examination : 10
Viva-voce : 5
Group Seminar : 5
Assignment : 5
PATTERN OF SEMESTER END THEORY EXAMINATION
Section Description Marks
A
Essay type questions-
Four questions are to be asked with
internal choice in each question ( Aor B).
One question from each unit.
Each question carries 10 Marks.
4x10 = 40
B
Short answer type questions - Eight
Two questions from each unit.
Student has to answer any 5 questions.
Each question carries 3 Marks.
5x3 = 15
C
Very Short answer type questions -
Ten questions are to be asked not more
than three questions from any unit .
Student has to answer ALL questions.
Each question carries 2 Marks.
10x2 = 20
TOTAL MARKS 75
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 28
SEMESTER: VI
CLUSTER ELECTIVE - A3
A3: ADAVANCED DIGITAL SYSTEM
Work load: 60 hrs per semester 4 hrs/week
Unit-I: Combinational Logic Circuits(18hrs)
Review Of Boolean and De Morgan's Laws-- Encoders-Decoders-Multiplexer-De multiplexer-SOP and
POS Forms-K-map four variable.
Unit-II: Logic Circuits(18hrs)
Shannon's Expansion Theorem-Consensus Theorem-K-map-Synthesis Of Multiple Output Combinational
Logic Circuits by Map Method - Static and Dynamic Hazards-Design Of Static Hazard Free Logic Circuits.
Unit-III: Threshold Logic(12hrs)
Threshold gate -realization of conventional gates-linear separability-unateness-threshold logic theorems-
synthesis of single gate and multiple gate threshold network.
Unit-IV: Programmable Logic Devices(12hrs)
Basic concept-Programmable Read Only Memory(PROM)-Programmable Logic Array(PLA)-
Programmable Array Logic(PAL)-Implementation of combinational circuits using PLA's and PAL's.-Moore
Machine -state diagrams.
Text books
1. Digital Logic and Computer Design--M Morris Mano
2. Computer System Design and Architecture- HeuringAnd Jordan
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 29
LAB EXPERIMENT LIST
IEEE Keywords USING COMPUTER LAB OR IC'S
1. Programmable logic arrays
2. Logic design,
3. Programmable array logic
4. 4X1 MUX
5. 1X4 DEMUX
6. 3X8 DECODER
7. 8X3 ENCODER
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 30
DEPARTMENT OF ELECTRONICS
MODULE V :: SEMESTER VI ( PAPER CLUSTER-A3) ADAVANCED DIGITAL SYSTEM
SCHEME OF EVALUATION
Examination Marks Remarks
Semester end
examination 75
Internal
examination
25
Written examination : 10
Viva-voce : 5
Group Seminar : 5
Assignment : 5
PATTERN OF SEMESTER END THEORY EXAMINATION
Section Description Marks
A
Essay type questions-
Four questions are to be asked with
internal choice in each question ( Aor B).
One question from each unit.
Each question carries 10 Marks.
4x10 = 40
B
Short answer type questions - Eight
Two questions from each unit.
Student has to answer any 5 questions.
Each question carries 3 Marks.
5x3 = 15
C
Very Short answer type questions -
Ten questions are to be asked not more
than three questions from any unit .
Student has to answer ALL questions.
Each question carries 2 Marks.
10x2 = 20
TOTAL MARKS 75
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 31
SEMESTER- VI
Cluster Elective: B
B1: POWER ELECTRONICS
UNIT-1: Power Semiconductors Devices (12hr)
Classification-Characteristics-Types Of Power Electronic Circuits-Power Diodes-Thyristor-Switching
Characteristics Of Thtristor-Thyristor Gate Characteristics-Series And Parallel Operation Of Thyristor-Heat
Sinks,Heating,Cooling And Mounting Of Thyristor-TRIAC-DIAC-LASCR-Power Transistor-Power
MOSFET-IGBT(insulated gate bipolar transistor)
Unit-2:AC to DC converters (18hr)
The principles of phase control-Converter classification-single phase half wave thyristor rectifier with RL
load-wheeling diode- single phase half wave thyristor rectifier with RLE load- single phase full wave mid
pointthyristor converter-full wave bridge rectifier feeding RLE load-single phase semi converter-three phase
half wave thyristor converter-three phase full converters-three phase semi converters
Unit-3: AC to A C converters (18hr)
Types of AC voltage controllers-single phase AC voltage controller supplying Rloads(phase control integral
cycle control)-three phase AC voltage controller-single phase transformer tap changer-cycloconverters-
single phase to single phase cycloconverters-three phase to single phase cyclo converters-three phase to
three phase cycloconverters
Unit-4: DC to D C converters (12hr)
Principles of chopper operations-step up choppers-chopper circuits-steady state time domain analysis of type
A chopper-thyristor based chopper circuits-multiphase chopper-control schemes
Text books
1. Introduction To Power Electronics-Jagannathan
2. Industrial And Power Electronics-Mithal And Gupta
3. Power Electronics-Bhimbra
4. Power Electronics Systems-Jai P.Agarwal
5 .Modern Power Electronics- P C Sen
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 32
LAB LIST:
(Any six experiments should be done) 1. Study of I-V characteristics of DIAC
2. Study of I-V characteristics of a TRIAC
3. Study of I-V characteristics of a SCR
4. SCR as a half wave and fullwave rectifier switch R and RL loads
5. DC motor control using SCR.
6. DC motor control using TRIAC.
7. AC voltage controller using TRIAC with UJT triggering.
8. Study of parallel and bridge inverter.
9. Design of snubber circuit
10. VI Characteristic of MOSFET and IGBT (Both)
11. Study of chopper circuits
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 33
DEPARTMENT OF ELECTRONICS
MODULE V :: SEMESTER VI ( PAPER CLUSTER-B1) EMBEDED SYSTEMS AND APPLICATIONS
SCHEME OF EVALUATION
Examination Marks Remarks
Semester end
examination 75
Internal
examination
25
Written examination : 10
Viva-voce : 5
Group Seminar : 5
Assignment : 5
PATTERN OF SEMESTER END THEORY EXAMINATION
Section Description Marks
A
Essay type questions-
Four questions are to be asked with
internal choice in each question ( Aor B).
One question from each unit.
Each question carries 10 Marks.
4x10 = 40
B
Short answer type questions - Eight
Two questions from each unit.
Student has to answer any 5 questions.
Each question carries 3 Marks.
5x3 = 15
C
Very Short answer type questions -
Ten questions are to be asked not more
than three questions from any unit .
Student has to answer ALL questions.
Each question carries 2 Marks.
10x2 = 20
TOTAL MARKS 75
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 34
SEMESTER: VI
CLUSTER ELECTIVE - B
B2: ANLOG AND DIGITAL IC-APPLICATIONS (60 HOURS)
Work load: 60 hrs per semester 4 hrs/week
Unit – I (10hrs)
OPERATIONAL AMPLIFIERS: Definition, Basic op-amp Ideal op-amp, Block diagram of op-amp,
inverting, noninverting, virtualground, Adders, subtractors, summing amplifier, voltage follower, op-amp
parameters, voltage to current convertor ,integrator, differentiator, differential amplifier, Logarithmic
amplifier.
Unit- II (15 hrs)
OP-AMP CIRCUITS: voltage regulator, comparator ,zerocross detecting circuit, instrumentational
amplifier, multivibrators-astable, monostable, Bi-stable, Schmitt trigger. sine wave generator, square wave
generator, triangular wave generator, Active filters(Basics)-low pass, high pass, band pass filters
IC-555 –functional block diagram and mention it’s applications
Unit-III (15hrs):
COMBINATIONAL & SEQUENTIAL LOGIC CIRCUITS (IC-Applications): Design of Code convertor: BCD to Seven Segment ,BCD to Grey, Grey to Binary.
Design of Counters using State Machine: Mod N counter, PresetTable,Binary Up/Down
Counter. Design of Universal Shift Register
UNIT-IV (10hrs)
DATA CONVERTERS: A/D converter:- Successive Approximation ADC,-Single slope and dual slope converter, Sigma-delta ADC,
D/A converter: R-2R Ladder network, Binary Weighted .
(ANALOG AND DIGITAL IC-APPLICATIONS)
LIST OF EXPERIMENTS
Work load: 30 hrs per semester 2 hrs/week
1. Op-Amp as inverting and non-inverting
2. Op-Amp as integrator and differentiator
3. Op-Amp as sine wave generator (Wien bridge oscillator)
4. Op-Amp as sine wave generator
5. Astablemultivibrator determination of frequency (using IC-555)
6. Schmitt trigger using IC-555 timer
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 35
DEPARTMENT OF ELECTRONICS
MODULE V :: SEMESTER VI ( PAPER CLUSTER-B2) EMBEDED SYSTEMS AND APPLICATIONS
SCHEME OF EVALUATION
Examination Marks Remarks
Semester end
examination 75
Internal
examination
25
Written examination : 10
Viva-voce : 5
Group Seminar : 5
Assignment : 5
PATTERN OF SEMESTER END THEORY EXAMINATION
Section Description Marks
A
Essay type questions-
Four questions are to be asked with
internal choice in each question ( Aor B).
One question from each unit.
Each question carries 10 Marks.
4x10 = 40
B
Short answer type questions - Eight
Two questions from each unit.
Student has to answer any 5 questions.
Each question carries 3 Marks.
5x3 = 15
C
Very Short answer type questions -
Ten questions are to be asked not more
than three questions from any unit .
Student has to answer ALL questions.
Each question carries 2 Marks.
10x2 = 20
TOTAL MARKS 75
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 36
SEMESTER: VI
CLUSTER ELECTIVE -B
B3: APPLIED MATHMATICS
Work load: 60 hrs per semester 4 hrs/week
UNIT-1: Partial Differential Equations(15hr)
Formations-solutions types of first order equations - Lagrange's Linear equations-Linear Partial differential
equations of second and higher order with constant coefficients.
UNIT-II: Boundary Value Problems(12hr)
Classification of second order linear partial differential equation-solution of one -dimensional wave
equation-one dimensional heat equation-steady state solution of two dimensional heat equation.
UNIT-III: Laplace Transforms (15hr)
Transforms of simple functions-Basic operational properties-Transforms of derivatives and integrals-inverse
transforms-convolution theorems-periodic functions-Applications of Laplace transforms for solving linear
ordinary differential equations up to second order with constant coefficients and simultaneous equation of
first order with constant coeffients.
UNIT-IV: Graph Theory(13hr)
Introduction and types of graphs-Basic terminology-Representation of graphs and graph isomorphism-
connectivity-paths-indirect and undirected graphs and isomorphism
TEXT BOOKS
1.Advanced Engineering Mathematics- kreyszig.E
2.Higher Engineering Mathematics-Grewal.B.S
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 37
CLUSTER ELECTIVE -B3
PRACTICALS
1.Write a program to perform basic operations of matrix using MATLAB
2.Write a program to perform Scalar product and dot product of vectors using MATLAB
3. Write a program to perform implementing dot division and dot power of assays using MATLAB
4.Write a program to generate cos and sin values on a single graph using MATLAB
5.Write a program to plot a overlying plot using MATLAB
6.Write a program to plot 2D graph with same random vectors and give the string modifiers can be used to
color data point and the style.
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 38
DEPARTMENT OF ELECTRONICS
MODULE V :: SEMESTER VI ( PAPER CLUSTER-B3) EMBEDED SYSTEMS AND APPLICATIONS
SCHEME OF EVALUATION
Examination Marks Remarks
Semester end
examination 75
Internal
examination
25
Written examination : 10
Viva-voce : 5
Group Seminar : 5
Assignment : 5
PATTERN OF SEMESTER END THEORY EXAMINATION
Section Description Marks
A
Essay type questions-
Four questions are to be asked with
internal choice in each question ( Aor B).
One question from each unit.
Each question carries 10 Marks.
4x10 = 40
B
Short answer type questions - Eight
Two questions from each unit.
Student has to answer any 5 questions.
Each question carries 3 Marks.
5x3 = 15
C
Very Short answer type questions -
Ten questions are to be asked not more
than three questions from any unit .
Student has to answer ALL questions.
Each question carries 2 Marks.
10x2 = 20
TOTAL MARKS 75
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 39
GOVERNMENT COLLEGE (AUTONOMOUS): RAJAMAHENDRAVARAM (Accredited by NAAC “A” Grade)
DEPARTMENT OF ELECTRONICS,
LIST OF PAPER SETTERS AND EXAMINERS IN THE BOS 2017-2018.
S.No. Name of the examiner Name of the College
1 Dr.Ch.Kanakarao Y.N.College, Narsapur
2. Dr.K.Venkateswarlu HOD Y.N.College, Narsapur
3. Y.L.Narayana S.K.V.T.College for Women
4. E.Nageswara Rao Govt.college , yelleswaram
5 Dr.P.L.Rambabu M/s A.V.N.College, Visakhapatnam
6 K.Ramesh C.R.R. College (M) Eluru
7 D.Ganga dharudu M.R. College, Peddapuram
8 P.P.Divakar C.R.R. College (M) Eluru
9 V.Venkateswararao C.R.R. College (M) Eluru
10 A.Veerabhadra Rao C.R.R. College (M) Eluru
11 L.S.R.Ch.V.K.Nageswararao C.R.R. College (M) Eluru
12 K.S.Ch.Srinivasa Rao C.R.R. College (M) Eluru
13 G.Vijayalakshmi C.R.R. College (M) Eluru
14 K.Ravikumar C.R.R. College (M) Eluru
15 A.Srinivasa Rao K.G.R.L.College , Bhimavaram
16 S.Srinivas K.G.R.L.College , Bhimavaram
17 B.Srikanth P.R.College (A),Kakinada.
18 Y.Sri Devi C.R.R. College (W), Eluru
19 Dr.S.V.Kumara Sastry S.K.B.R.College, Amalapuram
20 V.Radha Krishna S.K.B.R.College, Amalapuram
21 V. Ratna Sekhar D.N.R. College (A), Bhimavaram
22 S.Venkataraju D.N.R.College, Bhimavaram,
23 K.H.R. Singh D.N.R. College (A), Bhimavaram
24 K.B.S.Gopal C.R.R. College (M) Eluru
Dept. Of ELECTRONICS Govt.College(A),Rajamahendravaram
Board of Studies 2017-18. Page 40
THE END