Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 1 of 42
Common to all ranges Shutter Specification 1 May 2012
Common to all Ranges Shutter Specification
1. Components
1.1 Louvres The 89mm wide louver is the default
10
mm
[0
.394
"]
63.5mm[2.5"]
12
mm
[0
.472
"]
88.9mm[3.5"]
12
mm
[0
.472
"]
114.3mm[4.5"]
Note that 114mm louvres are not available in Larchwood (48, 63, 89mm louvre available in Larchwood)
1.2 Stiles and Rails– see individual range specs
1.3 Tilt rod Centre Tilt Rod position is the default.
13
15
.4
1.3.1 Centre tilt rod
When ordering multi-fold track shutter: If you choose centre tilt rod, the tilt rod will offset from the
centre. The standard offset for the tilt rod is 7mm from the centre. Tilt rod will be 7mm to the left
from the centre for the left panels, and 7mm to the right from the centre for the right panels. By doing
so, panel can be folded flat without tilt rods obstructing each other.
For 2 panels (LL or RR) and 4 panels configuration (LLRR), there is no need to offset 7mm from the
centre of standard tilt rod.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 2 of 42
Common to all ranges Shutter Specification 1 May 2012
7 m m7 m m 7 m m 2 .5 4 m m
LL
7 m m 7 m m 7 m m7 m m 7 m m
RLL RR R
1.3.2 Offset tilt rod
For a regular panel (hinged) offset is 25.4mm from centre of tilt rod to end of louvre on hinge side.
When a panel split with centre stile requires offset tilt rods, the centre of tilt rods will be placed in
25.4mm from the louvre end on the regular stile not the centre stile.
1.3.3 Gear (secret) tilt
For a regular panel (hinged) the gear will be placed in the hinged stile. For panels with centre stiles, the
gear will be placed in the outside stiles. The louvre operation will be split into 2 parts automatically when the
number of louvres connected to the gear exceeds the following limit:
63mm louvre 21pcs
89mm louvre: 14pcs
114mm louvre: 10pcs
The bottom part will have one more louvre than the top part if the louvre qty is odd. If the louvre qty is
even, the top and bottom part will have the same number of louvres.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 3 of 42
Common to all ranges Shutter Specification 1 May 2012
1.4 Frames NOTE: NOT ALL FRAME TYPES BELOW ARE AVAILABLE IN ALL RANGES.
PLEASE CONSULT THE “SHUTTER OPTIONS AT A GLANCE” FOR CLARITY
1.4.1 Frame types
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 4 of 42
Common to all ranges Shutter Specification 1 May 2012
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 5 of 42
Common to all ranges Shutter Specification 1 May 2012
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 6 of 42
Common to all ranges Shutter Specification 1 May 2012
Note that this option
(deep frames) carries a
surcharge.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 7 of 42
Common to all ranges Shutter Specification 1 May 2012
22.2
27.4
22.2
60.3
22.2
46.5
22.2
76.2
NOTE: For all Deco frames (Ridge, Camber,
Classic) there will be NO removable insert strip
on arched frames
Vintage Hang Strip
27mm
Vintage Hang Strip
46mm
Vintage Hang Strip
60mm
Vintage Hang Strip
76mm
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 8 of 42
Common to all ranges Shutter Specification 1 May 2012
1.4.2 Frame Fixing
To make frames easy to fit, mounting holes can be predrilled for L frames and Z frames. To cover the
mounting hole, plugs will be used. Please specify plugs & predrilled holes on order form if you require
this option. Note that this option carries a surcharge (Not available for Decowood)
1.4.3 Sill Plate Option
Where an outside mount or Z frame butts into an adjacent side wall, ceiling, or sill then a matching sill plate
option is available. Please specify when ordering frames as follows:
e.g. LRT(SP) – Frame on left & right with sill plate at the top.
LRT(SP)B(SP) – Frame on left & right with sill plate at the top & bottom
L(SP)RTB – Frame on top, right & bottom with sill plate on the left
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 9 of 42
Common to all ranges Shutter Specification 1 May 2012
1.5 T-Posts
1.5.1 T Post Types
LRT(SP)B LR(SP)TB
LRTB(SP)
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 10 of 42
Common to all ranges Shutter Specification 1 May 2012
1.5.2 T Post Defaults
T-Post location will be such that even panel widths are created,
T-Post type depends on the following:
Where one or no shutters hinge off a T-Post default is 25mm T-Post. Where two shutters hinge
off a single T-Post default is 44mm (ie LTL = 25mm T-Post and RTL = 44mm T-Post)
Where 25mm and 44mm T-Posts are used on a single order – 44mm will be applied to all
T-Posts to have extensions on the back to align with frames unless otherwise specified
Note that 44mm T posts are NOT available in Woodbury & Siberian Larch
1.5.3 T - Post location
For inside mount, window size is required. The first T-Post location is measured from the left edge of the
window to the centre of the first T-Post. The Second T-Post location is measured from the left edge of the
window to the centre of the second T-Post.
For outside mount shutter, frame to frame size is required. The first T-Post location is measured from the left
outer edge of the frame to the centre of the first T-Post. The Second T-Post location is measured from the
left outer edge of the frame to the centre of the second T-Post.
Default for panels with T Post – if no position mentioned then the panels will be divided so that they are
equal width
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 11 of 42
Common to all ranges Shutter Specification 1 May 2012
1.6 Corner & Bay Posts
Custom Bay posts are available on request
2. Colour Options – see specific material specification sheets
3. Panel size limitations – see specific material specification sheets
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 12 of 42
Common to all ranges Shutter Specification 1 May 2012
4. Mounting Types
4.1 Inside Mount
For hang strip inside mount, left and right sides are hang strips, top and bottom are light blocks.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 13 of 42
Common to all ranges Shutter Specification 1 May 2012
4.2 Outside mount
38.1mm
Window size
Frame to Frame size
38.1mm
L-frame Outside
Mount
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 14 of 42
Common to all ranges Shutter Specification 1 May 2012
5. Panel Configuration
5.1 Regular (Hinged) Panel
Please specify the stile type is butt, rabbet or astragal. Default is Butt stile.
5.1.1 Deductions
Gap between 2 panels where there is no hinge: Astragal stile (LR): 5mm Butt stile (LR): 2.5mm
Gap between panel and frame on top & bottom: 2.5mm
Hinge gap (self-mortise): 2.5mm
Hinge gap for Hang Strip inside mount: 3.2mm, when it is a Hang Strip inside mount program, we will deduct
3.2mm all around the window (top, sides& bottom).
The bottom clearance is (2.5mm) for a window and 5mm for a door.
5.1.2 Shutter used for door:
1.The factory will add extra hinges to support the panels.
2.Move the top and bottom hinges to 51mm from the end of stile instead of standard 101.6mm.
3.Bigger top and bottom rail. This will reduce the probability of the panels sagging and increase
strength.
Material Panel Configuration with 5mm bottom clearance
L, R, LR LL, RR, LLRR
Decowood, Siberian Larch &
Woodbury Warranty waived
Must order it with track, we will not
process it without track, even with
warranty waived.
Normandy, Basswood, WRC With factory Warranty With track or warranty waived
Where a single panel width is less than 228mm –
the opening stile will be rabbet to avoid the corner
hitting the frame
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 15 of 42
Common to all ranges Shutter Specification 1 May 2012
*Note: New default for meeting panels is rabbet stile
5.1.2 Hinged Layout
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 16 of 42
Common to all ranges Shutter Specification 1 May 2012
*Note: No warranty exists for 2 panels hinging in the same direction for Decowood &
Woodbury
5.2 Bi-fold Panels
The tracks and relevant hardware will also be supplied together with panels, header & pelmets.
5.2.1 Default Height Clearances
Top clearance: 50.8mm (track + wheel clearance) +19mm (header) = 69.8mm (default).
Bottom clearance: For opening 22mm (default) with bottom pivot, bottom track & spring loaded guides
For opening 18mm (option 1) with bottom pivot, bottom track & spring loaded guides
For opening 11mm (option 2) with bottom pivot, NO bottom track & guides
Pelmet size available (mm): 62X12 (default), 146X12, 101.6X12, 44X12
Header size available (mm): 19X100 (default), 19X160 and 19X200
Custom sizes are available on request. Any sizes bigger than default will be charged for.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 17 of 42
Common to all ranges Shutter Specification 1 May 2012
5.2.2 Default Width Clearances
Default: Spring Loaded Guide Option 1: Spring Loaded Guide Option 2: No bottom track
Hang strip/liner thickness will be deducted from window size and std. clearances will apply
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 18 of 42
Common to all ranges Shutter Specification 1 May 2012
5.2.3 Bi-fold Layout
*Note: No warranty exists for bi-fold installations with odd number of panels folding in
the same direction (e.g. LLL or RRRRR)
5.3 By-pass Panels
5.3.1 Default Height Clearances
Top clearance: 50.8mm (track + wheel clearance) +19mm (header) = 69.8mm (default)
Bottom clearance: 22mm (default) with bottom track & spring loaded guides
25.4mm (option 1) with grooved plant-on for nylon guides
35mm (option 2) with “piggy-back” plant-on grooved for nylon guides
11mm (option 3) with NO bottom guide/track
Pelmet size available (mm): 101.6X12 (standard), 146X12, 101.6X12, 44X12
Header size available (mm): 19X160 (standard), 19X100 and 19X200.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 19 of 42
Common to all ranges Shutter Specification 1 May 2012
5.3.2 Close By-Pass
5.3.3 Close By-Pass Layout
2 Track system (default)
SU bottom channel for close MDF bypass but SE
bottom channel for close wood bypass Nylon guide can be fixed below
either S channel or U channel
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 20 of 42
Common to all ranges Shutter Specification 1 May 2012
3
Track
System (Extra header & Tracks will be charged for an no warranty exists)
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 21 of 42
Common to all ranges Shutter Specification 1 May 2012
5.3.4 Open By-pass
5.3.5 Open By-Pass Layout (showing light blocks)
For U bottom channel (centre tilt rod) & SE bottom channel (centre & hidden tilt rod)
Nylon guide can be fixed below either S channel or E
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 22 of 42
Common to all ranges Shutter Specification 1 May 2012
For U Bottom channel with Secret tilt rod only
For 2 Track system (default)
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 23 of 42
Common to all ranges Shutter Specification 1 May 2012
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 24 of 42
Common to all ranges Shutter Specification 1 May 2012
5.3.6 Bypass Track Spacing
BLADE
SIZE
HEADER
WIDTH
TRACK SPACE (centre to centre)
CLOSE
BYPASS
OPEN BYPASS
U-BOTTOM CHANNEL SE - BOTTOM CHANNEL
(bottom guide) (bottom guide)
CLOSE OPEN REGULAR TILT ROD SECRET TILT ROD REGULAR TILT ROD
63.5 100 160 51 90 70 90
89 100 200 51 114 92 114
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 25 of 42
Common to all ranges Shutter Specification 1 May 2012
6. Default Bolt & Ringpull Positions
6.1 Track System
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 26 of 42
Common to all ranges Shutter Specification 1 May 2012
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 27 of 42
Common to all ranges Shutter Specification 1 May 2012
Note:
1. If bolts are requested on track system shutters, they will be installed as per the above drawings.
2. The general principle is that the bolt position will not be on the panel which will have spring loaded guide at
bottom. That is to say, it will be on right stile of the 1,3,5…odd number panels for L panel fold. It will be on the left
stile of 2,4,6…even number panels for R panel fold-----(always count from left to right) see the fold below as
example:
3. If both ring pulls and bolts are required on track system shutters then the ring pulls will on the same stiles as the
bolts.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 28 of 42
Common to all ranges Shutter Specification 1 May 2012
6.2 Regular (Hinged)
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 29 of 42
Common to all ranges Shutter Specification 1 May 2012
1. If bolts are requested on hinged system shutters, they will be installed as per the above drawings.
2. If both ring pulls and bolts are required on regular system shutters then the ring pulls will on the same stiles as
the bolts.
3. For Tier on Tier configurations, the bottom of the ringpulls will line up with the top of the bottom rails on the top
tier, and the top of the ringpulls will line up with the bottom of the top rails on the bottom tier.
6.3 General (Bi-fold & Hinged)
6.3.1 Where there are ringpulls and bolts
Where there is no divider rail, the ring pulls will be above the bolts as default. Where there are divider
rails, the bottom of the ring pulls will line up with top of divider rails.
Default Default Optional
(Always above 1st
divider rail) (Ring pull at center or at requested height)
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 30 of 42
Common to all ranges Shutter Specification 1 May 2012
6.3.2 Where there are no bolts, only ring pulls:
Where there is no divider rail, the bottom of the ring pulls will line up with the top of the bottom rails as
default. Where there are divider rails, the bottom of the ring pulls will line up with top of divider rails.
Default Default Optional
(Above bottom rail) (Always above 1st
divider rail) (Ring pull at center or at requested height)
Note: When a special ringpull height is requested, as default this will always be from the bottom of the panel to the
centre of the ringpull. Where a ringpull is positioned directly above the new bolt, the default height to centre will remain
at 181mm. Should ringpulls be required on both sides of the same stile then the one on the back will be positioned
100mm above the front one (centre to centre). Should 1 x ringpull be ordered for a LR opening the default ringpull
position will be on the R panel. Gold anodized bolts are only available as old type.
Old
Bolt
New Bolt
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 31 of 42
Common to all ranges Shutter Specification 1 May 2012
7. Fixed Louvre Options
Note: This option will be charged at the same surcharge rate as a Raised Panel option.
Available in two positions:
close or open at angle.
Fixed Close Position Fixed Open Position
Fro
nt o
f panel
Ba
ck o
f pane
l
(Default) B
ack o
f panel
Fro
nt of panel
Back o
f panel
Fro
nt of panel
Fro
nt of panel
Back o
f panel
64mm Louvre 89mm Louvre 114mm Louvre
Standard or default orientation for louvres will
be Fixed Closed “Dress Down” (bottom edge of
louvres will be closer to front side of panel), but
“Dress Up” option is also be available.
Please note orientation of adjustable louvres in
closing position is dress up.
Fro
nt o
f p
an
el
Ba
ck o
f p
an
el
Fro
nt o
f p
an
el
Ba
ck o
f p
an
el
Dress UpDress Down
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 32 of 42
Common to all ranges Shutter Specification 1 May 2012
8. Raised Panel Option
Available in Normandy and Cedarwood only
8.1 Combinations
Raised panel with louvres
Raised panel only
8.2 Specifications
305mm < raised panel section height <= 1219mm
8.3 Raised Panel Location(s)
Top
Middle
Bottom
All (if panel height does not exceed 1219mm)
8.4 Rails where shutter has no louvres
For a panel with raised panel section only, 76.2mm is the standard size for top, bottom and divider rail. The minimum
size for rails size is 76.2mm
Raised panel only Raised panel with louvres
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 33 of 42
Common to all ranges Shutter Specification 1 May 2012
9. Special Shape Shutters - NB Not all are applicable to Decowood
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 34 of 42
Common to all ranges Shutter Specification 1 May 2012
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 35 of 42
Common to all ranges Shutter Specification 1 May 2012
For the special shape shutters, we will send a drawing to you for approval. Please double check every dimension
that shows on the drawing to prevent any mistake or misunderstanding.
10. Tolerances
Width:
The width of the panel can be plus or minus 1mm from the order width.
Height:
The height of the panels can be plus or minus 1.6mm from the order height.
Divider rail location:
Divider rail location may be off by half a louvre. If ordering max. frame to frame size, measure from bottom of
bottom rail to centre of divider rail. If ordering window size, measure from bottom of window to centre of divider rail.
Allow for tolerance as follows: 1. For 63mm louvre can be off by +/-25mm
2. For 89mm louvre can be off by +/-38mm
3. For 114mm louvre can be off by +/-50mm.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 36 of 42
Common to all ranges Shutter Specification 1 May 2012
11. Clearances
Opening Type Configuration Louvre width
63mm 89mm 114mm
Clearances in mm from last point of protrusion to centre line of back panel
REGULAR/HINGED L or R or LR 42 55 67
BI-FOLD LLRR configuration (pivot or floating) 42 55 67
LLLLRRRR configuration (pivot or floating) 75 75 75
Where a Bi-fold configuration operates beyond the opening width the clearance measurement from the
wall or skirting (if present) is 55mm assuming that the operation will occur within the opening width. If
the Bi-fold operation occurs beyond the opening width then the clearance is 55mm for LLRR and
75mm for LLLL or RRRR or greater number of panels.
BY PASS Closed and Open 42 55 67
Front clearances in mm for By-Pass panels that have to move into cavities
Open Regular tilt 62 75 87
Open Secret tilt 42 55 n/a
Closed Regular tilt 40 40 40
Closed Secret tilt 25 25 n/a
Clearances between tracks centreline to centreline
Closed Regular tilt 51 51 51
Open Regular tilt 90 114 n/a
Closed Secret tilt 38 38 38
Open Secret tilt 74 100 n/a
Refer to By Pass section for options
12. Maximum Lengths
Finished products come in maximum lengths of 3600mm. Anything longer than that is supplied in 2 equal pieces.
Components for Cedarwood, White Teak and Normandy, ranges carry a maximum length of 1800mm.
Components for Decowood range carry a maximum length of 3657.6mm.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 37 of 42
Common to all ranges Shutter Specification 1 May 2012
13. Motorized Shutters
13.1 Material
Only available in Normandy and Cedarwood
13.2 Shape options
• All rectangular shutters except tier on tier
• Arched and angled shutters provided that the angle is not more than 45°
• Rectangular openings will have 8 pre-set louvre angles while shaped openings will have 6
13.3 Tilt Rod
Available with central and offset tilt rods only. No secret tilt option available
13.4 Louvre Size
Available in 63, 89 & 114mm louvre size
13.5 Panel Size Limits
• 750mm minimum panel height
• 1575mm maximum panel height
• Where the panel height is greater than 1575mm then the maximum height from the top/bottom of the end rail to
the centre of the divider rail must not exceed 1575mm
• Max 18 louvres (89mm) on one motor
13.6 Components
13.6.1 Module
• Uses 6 x alkaline or lithium batteries (rechargeable batteries must be used for solar option)
• Available in standard and solar options
• The module cover will match the finish of the shutter or will
be a solar panel for solar option
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 38 of 42
Common to all ranges Shutter Specification 1 May 2012
13.6.2 Louvre Cap
Available in Silk White, Pearl, Bisque, Antique Brass, Bright Brass, Silver & Black (default will match hinge
colour chosen)
13.6.3 Remote
• Uses 2 x batteries
• Can be set to operate one or multiple panels at the same time
• Operates from a distance of up to 12m
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 39 of 42
Common to all ranges Shutter Specification 1 May 2012
14. Hardware Self-mortise hinge: (one marked with “N” and another with “M”)
N - Type used for panel to frame in Normandy, Basswood and Western Red Cedar
M - Type used for panel to frame in Decowood and panel to panel in ALL materials
N M
Rabbet hinge: Used for Rabbet stiles. (Hinge pin is removable) L hinge: Used for hang strip inside mount.
Hinge colour options: 7 finishes
White / Bisque / Pearl / Antique Brass / Bright Brass / Stainless Steel /Black
Stainless steel hinge comes with surcharge.
The number of hinges supplied will be determined by the panel height:
Panel height
No. of hinges (All ranges
except Decowood)
No. of hinges
Decowood
Panel Height<=1219mm 2 2
1219mm< Panel Height <=1981mm 3 3
1981mm< Panel Height <=2438mm 4 5
2438mm< Panel Height<=3048mm 5 6
Panel Height >3048mm 6 7
All hinges are 60mm
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 40 of 42
Common to all ranges Shutter Specification 1 May 2012
Magnetic Catch
Hoffmann Key: For joining frames together Bottom channel:
Surface mount Surface/Flush mount
(default)
36
11.4
9.5
9.5
mm
19.2mm
11.4mm
7.5
mm
Ringpull Bi-fold hardware
L shaped plate
Old round magnet
New square magnet
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 41 of 42
Common to all ranges Shutter Specification 1 May 2012
Warranty for Decowood, Woodbury, Normandy, White Teak, Larchwood and
Cedarwood shutters
We warrant our products to be free from defects in materials or workmanship as per the below
schedule. Provided that such products were properly installed; and such products were made or
assembled exclusively from original materials and components. Any resale or other transfer of the
product and/or materials after the first six (6) months voids this warranty.
Repair, remake or refund of defective products are the remedies under this warranty for the first six
months after installation, thereafter the sole remedy will be repair or remake of defective products.
Repairs will be made with only like or similar parts. During the first six months, this warranty does
include shipping charges, costs of labour for measuring, installation, or trip charges, thereafter it will
be excluded.
American Shutters shall not be liable for any loss or damage of whatsoever nature, including
consequential loss or damage arising out of delays or failure to deliver due to fire, explosion,
unavoidable breakdown of machinery, government acts and/or regulations, strikes, war (declared
or not) or by any other acts of God or similar circumstances which are reasonably beyond the
control of, and unforeseen by, American Shutters.
This warranty does not cover any condition of or damage to the shutter or window, from
unauthorized repairs, accidents, alterations, misuse, abuse, act of God, motorized devices, daily
wear and tear or failure to follow the American Shutters instructions with respect to measurement,
installation, cleaning or maintenance. Improper, inappropriate, or unauthorized replacement parts,
repairs or maintenance voids this warranty. Due to manufacturing, natural variations in colour, grain
and texture in products, American Shutters is not able to guarantee exact matches on subsequent
orders. Returns cannot be authorized due to these normal variations.
Confidential - Norman Shutters are exclusively distributed by AMERICAN shutters Page 42 of 42
Common to all ranges Shutter Specification 1 May 2012
Product Finish
(Where applicable)
Warranty (Years)
Workmanship
& Materials
Colour
Fastness
Interior shutter
Decowood 3 3
Normandy
Painted / Stained 3 3 Larchwood
White Teak
Cedarwood Painted / Lacquered 3 3
Oiled 1 0
All ranges Raw unfinished 0 0
Hardware Stainless steel 3 3
Non-Stainless steel 1 1
Exterior
shutters
Larchwood
Cedarwood
Painted (Light colour) 3 3
Painted (Dark colour) 3 5
Stained (Light colour) 1 1
Stained (Dark colour) 1½ 1½
Cedarwood Oiled 1 1
All timber ranges Raw unfinished 0 0
Hardware Stainless steel 1 1
Non-Stainless steel 0 0