Download - CLEARED - University of New Mexico
![Page 1: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/1.jpg)
—. —
Sensor and Simulation Notes
Note 338
March 23,1992.
MODELING HYBRID EMP SIMULATORS WITH GAP FEED LOCATIONSFAR FROM THE RF SOURCE
C. ZuffadaJ. Martinez
Kaman Sciences CorpomtionAdvanced Elec~omagnetics Division
2800 28th S&eet Suite 370Santa Monica, CA 90405
C. BaumW. Pm-her
Phillips LaboratoryKirtland AFB, NM 87117
ABSTRACTI
Recently a new hybrid EMP simtilator has been developed where the signal is transmitted by ahigh-quality coaxial cable from a RF source on the ground to a point above the ground where thecable is cut to create a gap source. The cable is made part of the antenna by passing it throughchokes which provide a frequency dependent inductively coupled impedance, thus making thecable-shield exterior effectively loaded for exterior scattering purposes over a wide band offrequencies of interest. Two geomernes have been analyzed and practically implemented and asimple analytical model has been developed to make current and field predictions. Comparisonsarc presented between measurements and calculations.
CLEARED
![Page 2: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/2.jpg)
.
CONTENTS
1.0
SUMMARY ...................................................................................................................4INTRODUCTION ..........................................................................................................5
FUNDAMENTAL CONCEPTS ....................................................................................6
2.0 PHYSICAL DESCRIPTION OF THE ANTENNA ....................................................142.1 Suspension System ..............................................................................................2.2 Feed And Associated Electronic Equipment. ......................................................::2.3 Properties of Ferrite Beads For RF Suppression .................................................182.4 Antenna Input Impedance ........................................................................,.,,..,,..,24
3.0 MATHEMATICAL MODEL OF ANTENNA PERFORMANCE .............................263.1 Current Calculation - Perfectly Conducting Ground. ..........................................3.2 Current Calculation - Lossy Ground Accounted For ..........................................;:3,3 Potentials And Fields ......................................................................................,,..31
4.0 COMPARISON BETWEEN MEASUREMENTS AND CALCULATIONS .............354.1 AvaiIabIe Measurements .....................................................................................4.2 Antenna Properties And Field Characteristics ....................................................?2
4,2.1 Triangular Geome~ .................................................................................354,2.2 Elliptical Geometry ...................................................................................56
5.0 DESIGN IMPROVEMENTS .......................................................................................68
REFERENCES .............................................................................................................69
2
![Page 3: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/3.jpg)
.
ACKNOWLEDGEMENTS
● We wish to thank Dr. D. McLemore of KSC, Mr. B. Burton formerly of Kaman SciencesCorporation and Mr. T. Tran of Phillips Laboratory for their assistance with the field mappingeffort for both antenna configurations.
3
![Page 4: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/4.jpg)
SUMMARY
.
This note describes the features of an illuminator which offers flexible geometry, ease of
construction and handling, and low cost. It consists of a loop arbitrarily shaped in principle,
made with a coaxial cable and simply cut open at some point to create a gap source, with currents
flowing along the exterior surface of the cable outer conductor, and through a properly chosen
loading impedance. Because the basic idea rests with the feed rather than the antenna shape, we
refer to it as the Wormhole Feed Concept, as will be explained in Sec. 1. Such an antenna
concept was implemented recentJy in two geometries, tiangular and semieIliptical. The
description of these particular antennas and the related instrumentation set-up is presented in Sec.
2.
To characterize the ekctromagnetic features of such an antenna a mathematical model was
developed to calculate currents and fields; this is detailed in Sec. 3,Section 4 presents a
comparison between modeI predictions and actual field map measurements, showing a very
satisfactory agreement between the two. This suggests that the important features of the antenna
are understood and well described in the mode~of Sec. 3. Finally, some recommendations for
design simplifications/improvements are offered in Section 5.
7
4
![Page 5: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/5.jpg)
.
. INTRODUCTION
@Recently the interest of the community involved with assessing system’s vulnerability to RF
signals, such as EMP, has turned to low level continuous wave testing techniques as a possible
supplement to the more costly, traditional high level pulse methods. In fact, in addition to cost
savings, there are several advantageous features to continuous wave testing, one of which is the
availability of simple, “portable” illuminators which can generate smooth, plane-wave-like fields
over wide frequency ranges and reasonably large volumes. For linear systems, by measuring the
system’s response at each frequency of interest one can determine a “transfer function” operator
which, when multiplied with the spectrum of any given RF threat, will generate ~e spectrum of
the system’s response to that threat. An inverse Fourier transform will then allow to calculate the
time domain response.
Resistively loaded loops have been used for this application because of their ability to produce
fields at low frequency (quasi static limit) as well as at high frequency when the radiation
emanates from a relatively small region around the source location. By proper choice of the
resistive load the ratio E/H at the center of a loop in air can be made txqualto 377 Q in the low
frequency limit, Additionally the resistance damps the loop resonances and enhances the antenna
bandwidth. Various geometries are possible depending on spec~lc field requirements. One such
●geometry is a semi ellipse above the earth with a source at various possible locations, including
the highest point above the ground. For this geometry it was shown [1] that the optimum
resistive loading depends on the source location and deviates somewhat from that of a circular
loop of the same perimeter [2], which is independent of it, due to the symmetry of the antenna,
Concerning the source location, it is often desirable to produce electric fields which are
horizontally polarized. This requires the source to be at the highest point above the ground. Up
to now, in this case, the signal coming from the network analyzer is made to travel inside a
coaxial cable to an amplifier located under the antenna, at its center, From there a coaxial cable
brings the amplified signal up to the actual feed point above the ground, where some matching
network is employed to drive the antenna. Such a cable is a large scatterer and it will cause
perturbation of the fields in the volume where the test object could be located. The perturbation
can be minimized by placing it in a plane where the electric field is perpendicular to it but this
solution prevents the test article from being positioned under the antenna, where the field levels
are the highest, and have desirable spatial properties [2]. This note describes a feed concept
which eliminates the presence of the cable and/or other instrumentation in the working volume,
by making this cable part of the antenna,
![Page 6: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/6.jpg)
1.0 FUNDAMENTAL CONCEPTS
The basic ideas for an illuminator which allows for a part of the antenna to be also part of the
feed without compromising its electromagnetic environment are presented in [3}, This section is
a reproduction of Sec. 2 and 3 of that note.
The probIem with a long slender conductor (such as a coaxial cable shield) is that, if there is a
component of an incident electric field parallel to the path of this conductor, then large axial
currents are induced with associated large scattered fields. Incident electric-field components
transverse to this path scatter relatively little, such scattering being related to the small transverse
dimensions of the conductor.
One way to look at this is the asymmetry in the physical world seen in the presence of electicaI
conductors (e.g., metals), compared to the lack of magnetic conductom (due to the apparent lack
of magnetic monopolies). One might consider an ideal magnetic boundary as in Fig. 1A for its
possibIe use in containing conductors (cables) inside a long sIender magnetic tubular boundary.
This isolates the interior cable from the external fields (no currents on the cable exterior).
However, by forcing the external axial magnetic field to zero this kind of a “shield” is also a
large scatterer of the external fields. This is just the dual (interchanging E and l%)of a slender
conductor. Of course, there is no such ideal magnetic conductor, but it can be approximated by a
pipe with a high permeability (and thick) wall as in Fig. lB. This also shows part of the problem
in such an approach in that a large axial magnetic flux is induced in the wall of such a pipe.
A way out of this problem of e~ectric versus magnetic boundaries is to mix them, i.e., expose
suitable short lengths of the conductor (cable shield) to the external incident electric field, while
separating these by use of inductive magnetic cores (effective magnetic boundaries) as indicated
in Fig. 1C. Such cores represent a localized high impedance (a choke) limiting the current
induced on the conductor. For sufficiently kuge impedances we can think of the exterior
scattering as being from a colinear array of unconnected short conductors. This scattering will be
small provided core spacing d is smaIl compared to the half wavelength. Note also that the
separation between cores breaks up any significant increase of magnetic flux parailel to the
conductor. In the limit of a large number of separated cores we can think of a dielectric/magnetic
sandwich comprised of dtemate thin layers of magnetic material separated by thin dielectric
layers as discussed in [4]. Here we are looking at such a structure from the exterior properties as
compared to the interior emphasis in [4]. Even with separated cores as in Fig. 1C, the individual
cores might be constructed in such a sandwich form for high-frequency purposes.
6
![Page 7: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/7.jpg)
.
magnetic/ boundary
cable‘$
Y
/
:>
------ —----- ------ ------ l---,,,,,------ ------ ------ ------ ----..
<+H tan=;
A. Tubular magnetic boundary
( plargeo negligible
cable ------ ------ ------ ------ ----------------- ------------------------- ------ ------ ------ -----~ -
------ ------ ------ ------ -----e .
<+H tan .9r!aJI
B. Pipe of high permeability
tcj +
C. Spaced inductive cores
Figure 1. Progression from Magnetic Boundary to Spaced Inductive Cores.
![Page 8: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/8.jpg)
.
With this general concept of effectively isolating the conductor by the alternating .electric/magnetic boundaries for the exterior fields we can think of this in topological terms.
This is analogous to a worn-hole which conceptually returns electric flux lines (to make them
cIosed) between positive and negative charges [5]. This wormhole is postulated to pass beween
the charges in some higher dimension of space. Another paper [6] shows how a special helical
transmission line can propagate an effective magnetic monopole with the magnetic field lines
closing by returning through the tube formed by tie helical solenoid. In the present case a well-
designed alternating electric/magnetic boundary gives something like a wormhole, in the sense
that a signaI cable can pass between two points in three-dimensional space without being there
(approximately) in an exterior electromagnetic scattering sense.
Having a technique to approximately hide a conducting cable, the next question is where to place
this cable path with its special “shield”. Referring to Fig. 2 the topological problem is where to
place this path with endpoints at B and somewhere on the earth surface. As mentioned
previously, the path should be excluded from the test volume since the system under testis to go
there. Furthermore, one would prefer that this path not be close to the test volume because its
shieId is as a practical matter imperfect (non completely invisible).
Observe that there are already two earth-contact positions, A and C, for the simulator proper
(antenna). At these locations there are ground rods “already” in place. One could use either A or
C, but since one of these maybe closer to B(i.e., C in the Fig. 2 example), we may choose this a
one and make our conductor path connect B and C. The next question concerns where the
conductor path from C to B should be placed. An obvious choice is to place it along the same
path as the resistively loaded antenna s&ucture where it can be supported by the same dielectric
support structure (poles, catenary, etc.).
Then, as in Fig. 3A, consider that there is a current I along the antenna path consisting of wire-
connected resistors, each of value
~=R’—v
vs number of resistors per meter (I)
Let the adjacent cable path have its inductive cores (chokes) spaced the same as the resistors (v
per meter) giving
8
(2)
![Page 9: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/9.jpg)
.
resistively loaded
-----------------
\\ //
\\ //\\ /
\’\\~//
~/ =’~~———— ——
‘1’image
Figure 2. Hybrid EMP Simulator.
![Page 10: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/10.jpg)
.
I
R i mnnectionlx
- [ p~hs % ~[ [. . . I ,,. I
,,, . . .
,,, . . .
,../ _
. . .
– \(C17cEs)
A, Resistively-loaded wire in paraliel with cor~loaded cable
-- ~ , - ,, ● ☛☛☛
✌✌✌ ✎ ✎
✌✌✌ ‘,
,... .
U
B. Current diverted to cable-shield exterior
I 10*e O
I. . . .’,.,. . . . .. w. . . ,.
. . . ,.- 2
C. Current through resistors separated fromoppositecurrenton cable-shield exterior
FQure 3. Progression from Adjacent Paths to Common Path for Resistively-Loaded Cable-ShieldExterior.
10
![Page 11: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/11.jpg)
.
and positioned adjacent to the resistors. With negligible current on the cable-shield exterior (for
●half wavelength ?t./2>xi), let us electrically connect each wire between resistors to the
corresponding adjacent position on the cable-shield exterior via the connection paths in Fig, 3A.
Negligible current runs on these connections. Then as in Fig. 3B deform the wire and
connections so that the current I passes through the resistor to the cable shield and back to the
next resistor, etc. Negligible current still passes through each choke on the cable-shield exterior.
Then in Fig. 3C the wires connecting each resistor to the cable shield on opposite sides of a
choke are slid together (inside the choke), connected to each other, and removed (not necessarily)
from the cable shield. Now I flows on the cable-shield exterior through the choke but is
cancelled by an opposite I on the wire connected (both ends) to the resistor. The choke now acts
as a transformer.
The two paths have now become one. There is a signhlcant, but con~olled, current I on the
cable-shield exterior. The cable shield should be a good one, say a continuous metal tube
(aluminum or copper) instead of a braid. This is consistent with a high-quality foam-dielectric
(or similar) coaxial cable capable of efficiently tmnsmitting signals in the GHz range. The
requirement to make the cable “invisible” by the special alternating elec&ic/magnetic boundary
has been made a little easier. It need not prevent “all” current from flowing on the cable-shield
e
exterior, but merely limit it to I, the value desired for the antenna.
Figure 4A shows a view along the cable axis of the core and loading resistor (with wire linking
through the core). The current I (approximately) in this wire associated with the resistor is not
centered in the core, giving a non uniform excitation of the core. One can compensate by
offsetting the cable shield to obtain better angular uniformity for the magnetic field associated
with the common mode (small) of the currents on this wire plus cable-shield exterior. Better
still, one can replace the single resistor of resistance R by N resistors, each of resistance NR
spaced at equally angles (27t/N) around the core as indicated in Fig. 4B. This gives a more
uniform current and magnetic-field distribution in an angular sense around the core. One can
extend this concept by replacing the wire loops by a continuous metal structure with a
circumferential slot around the outside [7, 8], the N resistors being connected across this slot.
If the core is approximated as a simple inductance L, then define
(3)
The effective impedance of the resistor-loaded cores is then
,
11
![Page 12: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/12.jpg)
.
A. Single resistor
●●
●
B. Multiple (N) resistors in parallel
Figure 4. Resistively Loaded Cores.
NR
12
![Page 13: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/13.jpg)
[1-1
●Z(S) =R1/(SL)= *+*
s = Q+ jco s Laplace - Bansfoxm variable or complex frequency (4)
In this form the resistor-loaded cores give an effective impedance per unit length R’ for this
antenna/cable path provided
(00 <c 0) (5)
For a given R’ then one can choose v(=l/d) and L to make co. some desired low-frequency limit
on the ideal performance of the antenna.
k a more general sense the choke impedance ~Ch(s) need not exactly follow an inductive form
SL for L constant (Xl). In this more general case we have
[11 1 ‘1z(S)= R//~ch(S)= ‘+-
R Zch (S)(6)
For R’ to dominate the antenna performance we require
~ch(@) >> R (7)
for frequencies of interest, so it is important only that the choke impedance be large compared to
R. As one increases the number of resistors (decreasing d) R is decreased, making the
requirement of Eq. (7) be met for a broader band of frequencies.
The following section describes a practical implementation of the basic ideas discussed above,
Ferrite cores were used to generate the necessary ~ch (jco) and, as a fmt step, the cores were not
loaded with resistors. The objective was to demonstrate the concept and our present choice of
materials, parts and design features are not necessarily optimal, Two shapes have been
investigated: a triangular half-loop and a semielliptical half-loop.
13
![Page 14: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/14.jpg)
2.0 PHYSICAL DESCRIPTION OF THE ANTENNA
2.1 Suspension System
The fmt version of the Wormhole Feed Concept (Fig. 5) consisted of a coaxial cable
(characteristic impedance = 50 Q, outer diameter (2r) = 7/8”) shaped to form an approximately
triangular loop of height (h) --20 m and base (2b) -80 m, laying in a plane perpendicular to the
ground and suspended at the apex via a dielectric rope. To relieve the coaxial cable of the
tensioning action, a ny~on rope was laid along the cable in the desired geometrical shape of the
illuminator and the cable was made to follow the intended shape by use of clamping pIastic
sleeves, positioned every few meters, which allowed for free movement of the cable with respect
to the nylon rope when the latter was tensioned,
The support system is ideally provided by s~etching a dielectric rope between two wooden poles,
which was implemented at Kirt.Iand when the concept of this illuminator was first demonstrated.
In that case the existing Achilles HI [9] support system was used and the tension on the
suspension rope was adjusted so that the desired antenna height of 20 m was obtained. Later on
this design was simplified and improved by eliminating the portion of coaxiaI cable laying on the
ground, relocating the amplifier outside the working volume, and grounding both ends as shown
in Fig. 6. From the elecmomagnetic standpoint the latter configuration has the advantage of
providing a working volume free of instrumentation and eliminates the accumulation of charges
between the horizontal portion of cable and the earth.
In addition to the triangular geometry the semielliptical geometry was also implemented (See
Fig. 7) using the same support system and overall design, To shape the cable into a semi efipse
(Ellipticus) a slightly more complicated dielectic support system was necessary.
2.2 Feed And Associated Electronic Equipment
A signal from a network analyzer is fed via a coaxial link to an amplifier, whose output drives
one of the coaxial legs of the antenna from one vertex. At the apex the ~oaxial cable is opened
up and its center conductor is connected to the shield of the other coaxial leg, either directly or
via a “transformer” (See detail of Figs. 5 and 7). This second Ieg has its center conductor shorted
to its shield. The mechanical support of the gap is provided by a piece of plexiglass to which the
two halves of coaxial cable are attached and held in place by means of plastic straps (see inset of
Figs. 5-7). The shields of both legs are grounded to the earth, and to the ground of the amplifier.
It is noted that the actual feed point of the loop is the apex, which can be regarded as a gap
14
![Page 15: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/15.jpg)
/
/
I-J /c-n
/I
//
//
/
---——_ _ --’-’+-4-”----------”\l-71
\
\
\
\
\
\
\
\
\
\
Figure 5. Triangular loop geometry, fmt design.
![Page 16: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/16.jpg)
----—-- —--- —----
/z
Figure 6. Triangular loop geometry, second design..
,
“\\
\\
\\
\\
\\
ti
● ✎
![Page 17: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/17.jpg)
. shorting
+“$
\Qo\
-—-—_ _,————_ _.
-— ---
\\
\
L source$
xr
v
/ z
i\
\
\
\\
\\
Figure 7. Elliptical loop geometry.
![Page 18: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/18.jpg)
source, and the shields of both legs se~e as linear conductors for the flow and radiation of
current. To insure smooth fields over a wide frequency range the antenna is loaded with ferrite
toroidal beads designed to provide both inductive and resistive losses, symmetrically placed
along its legs. Ferrite toroids characteristics and the rationale for our choice of units and their
placement along the antenna are presented in Sec. 2.3.
2.3 Properties of Ferrite Beads For RF Suppression
Ferrite beads and toroidal cores are used extensively to provide attenuation of unwanted RF
signals in systems, subsystems and circuits. To accomplish this, use is made of the losses that
such rneterials present over a wide spectrum of frequencies. Such losses, due to eddy currents,
hysteresis and residual core losses (relaxation of magnetic domain walls) are such that the device
can be modeled simply as a frequency dependent R-L series impedance; at relatively low
frequencies the inductive portion is dominant, while the resistive part becomes dominant at
higher frequencies. The overall impedance is smaJI at low frequency, then it increases, reaches a
broad maximum and eventually decreases, as shown in Fig. 8, for three types of ferrites. When
used as RF suppressors the ferrite material basically acts as a “low pass falter” whereby the
frequency of the desired signal must be low enough so that the losses of the chosen femite are too
low to affect it. On the contrary, at higher frequencies, the increasing resistance acts to
progressively reduce the unwanted signals that propagate along the path where the ferrite
toroid/bead has been installed. The choice of ferrite material is mainly dictated by the required
suppression band, and more than one type of material might be necessary for wide-band
operations.
Our design shares some aspects of the RF suppression problem described above. When the
antenna is not loaded the loop resonances would give rise to electromagnetic fields such as those
shown in Fig. 9 at the points (0, 3, 20) (The reader is referred to Fig. 5 for an illustration of the
Cartesian coordinate system used for this problem). Such behavior has its origin in the
interference between the current flowing along each leg directly from the-source and that coming
back from the other leg after having &aveled along half the loop. One can see that the extremely
wide variations of tie field components make this antenna unsuitable for simulating a smooth
plane wave environment. To damp the resonances the antenna was therefore loaded with 240
ferrite beads distributed as follows; 120 material #43 ferrites were originally placed along the
antenna legs, spaced roughly uniformly for the demonstration test in Albuquerque, but during the
test five were broken. Furthermore, 120 material #77 ferrite beads were originally distributed
along the base of the antenna, uniformly spaced; however, breakage of ten units occurred during
the tests. The optimum number of beads was determined empirically by increasing their number
●18
![Page 19: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/19.jpg)
.
OEI0
T ‘-
J_--L---A- L--c--l
1(Y 10’ I@ 1(Y
A = 2-4”
B = 1.4”
c = 0.5”
Figure8. Pmpcrties of ferrite beads for three diffcxent mattials, identifid by thti ~“d
names, and provided by manufacturers#64 permeability 250#43 permeability 850#73 permeability 2500
![Page 20: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/20.jpg)
10-7 ~ io”4 p , ---?3
10-8
10-9
lo-i”
lo-iif
10-5
10-6
10-7110-B
10-9
lo-i”
[ ~ llllA ~ lll-! 1 ‘III*l![0, 3, 201 Bz (T)lo-if
Nk
(0, 3, 20)0 10-12 - 10-’2 ~———————
,
Bz (T), ,
104 10” 10” 0.0 5. 0E+07 i . 0E+08 i . 5E+OB 2.0E+08Freq (HzjO’ Freq (tiz)
Figure 9. Effect of femite loading on the magnetic induction at (O,3, 20).Solid curve - Calculation without ferrksDashed curve - Measurement with ferrite loading
![Page 21: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/21.jpg)
in three steps and observing that the measured Bz field along the antenna axis at the distance of
20 m exhibited an increasingly smooth behavior up to 200 MHz. It is pointed out that the
notation #43 and #77 are widely used commercial names, identifying the metals used in the
ferrite compounds.
The ferrite beads impedance was obtained experimentally for each material in two steps. First,
by loading the end of a coaxial cable with a wire through which 10 ferntes have been routed, the
series impedance for the ten elements can be obtained through direct measurement of the
reflection coefficient. This procedure is required to obtain accurate measurements at low
fkequency, i.e. up to a few MHz,”where the amplitude of the reflection coefficient for one single
bead is too close to one and the phase to 180” to allow a correct reading. On the other hand, at
high frequency the series combination of ferntes in~oduces a capacitive effect which lowers the
impedance. Therefore, a second step is necessary where only one ferrite is passed through the
wire for a correct measurement at high frequency; the low frequency and high frequency values
of the reflection coefficient are then combined, In summary, the operation to be performed is the
following
=501+pmZf —
l-pm(8)
where pm is the measured reflection coefficient and 50 (Q) is the characteristic impedance of the
coaxial cable used for the experiment. If ten ferntes are measured the value of Zf thus obtained
must be divided by 10. The impedance for material #43 and #77 single beads (outer diameter =
2.4”, inner diameter = 1.4”, height = 0,5”) derived as described above are illustrated in Figs. 10
and 11.
Our particukw choice of ferrite material satisfied the need to damp current in a broad frequency
range, as indicated by the impedance values shown in the above figures. The placement of
material #77 ferntes along the base of the triangle was justified by the fact that their effect is
important at low frequency, as evinced from Fig. 10. Since at low frequency the antenna is
electrically small the location of these beads is not very critical to provide an attenuation of the
return current from one leg back to the other, because the variation of the current along each leg
is small. At high frequencies, however, the variation of the current is rapid and an effective
damping is achieved only if the ferrites are placed all along the antenna legs, starting horn the
source point. However, in the improved design both species of toroids were distributed all along
the legs, alternately, but with somewhat random separation. The field smoothing process is
accomplished here at the expense of its level, since a lot of the energy is dissipated in the loading
71L.1,
![Page 22: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/22.jpg)
IvN
i(f
Ioi
c 10°
10-i
Amplitude
10-2 A..Uii 1 -f10 10=
710° 10
Frfq (Hz)
Ic? E ,, I 1 ‘xl
10-2 1 I
10°7
13 ioFr~q (Hz)
90.00
67.50
WIaaJ&45. ooa?u
22.50
0.01(
T “’”’’’”“--’”’”“’”mPhase
t6
* 1 I u10
7108 1(
Frfq (Hz)
10-tI Imaginary Part
10-2 1 I
1087
13Fr~q (Hz)
Figure 10. Memuwl impedance for one ferrite toroid made with material #77 (manganese-zinc).
![Page 23: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/23.jpg)
10-i 1 f 1 * * t
l.o 106I 0
10 10Fr~Oq (Hz)
!=
101
18
10-i
90.00
67.50
: 45.00L
%
22.50
G
I I 1 .11-
Phase
0.0 f 1 I ,105
,
1061
1084
5
Frfq (Hz)
1$
101
18
1- -i10-:k
E Imaginary Part
10-2 ,.[ , , n ,
iog
,,
10=7
2 Ii?Fr~q (Hz)
Figure Il. Mmsutifi@mcc foroncftite toroidmtic titimtctid W3(tickcl-tinc).
![Page 24: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/24.jpg)
elements. This effect is illusmted in Fig. 9 where the magnetic induction calculated at (O,3, 20)
in the absence of the ferrites is conbzwted with that measured under load condition. One can
notice that as a result of loading, the antenna resonances are shifted down in fr~uency, and are
attenuated and broadened. A more comprehensive and quantitative description of the field
properties with ferrite loading is presented in Sec. 4, where measured data are analyzed and
compared with calculations obtained from a simple mathematical model of the antenna behavior,
2.4 Antenna Input Impedance
The antenna input impedance was obtained from measurements of the reflection coefficient at the
actual feed point, according to Eq. (1), and is presented in Fig. 12, displayed both as amplitude
and phase and as real and imaginary part. Note the double peak, one around 400 kHz and the
other around 900 icl%, with a small vaLleyin between, which corresponds to a passage of the
phase through zero three times. One can conclude that the fmt resonance point occurs roughly
around 600 kHz actually there are two resonances, slightly splitted. A second resonance takes
place around 900 kHz, beyond which the behavior of the antenna is capacitive. It is shown that
the input impedance is always higher than the characteristic impedance of the feeding cable (50
Q), and a substantial mismatch occurs at the antenna apex, resulting in a reduced efficiency.
To minimize the impedance mismatch, a 50 Q low induction resistor was connected in parallel
with the antenna input gap, since time constraints did not allow us to ~ out a more refined
matching device. Future effort should be directed to designing a matching network for this
antenna which optimizes the radiated fields. The present design results in a Iot of wasted energy
into the resistor.
24
![Page 25: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/25.jpg)
103
i-1- 4
(a)
..
-,
3500.
1750. t
co
-1750.
-3500..
1(
(c)[ # t,#1 [11 # , 1 , *111 , 1 , # # 11,1 n * a , 1 ,,
1087
10° 1Fre;” (Hz)
45.
-45.
-90,
1
3500.
i750 .
-1750.
-3500.A4.
—.
~- ‘ , s # 8 ,
, , Ill
(b), , , , ,Ifi , , , 1 , , ,,1 # -LL1,,I , , , L
1067
108Fre~O [Hz)
109
I
(d)1 e 10,,,,1 , 9 *,I u-l
I, 1,1 [ ,, * , ,,
1067
Ioe logfre~” (Hz]
Figure 12. Antenna input impedance, displayed as (a) amplitude (b) phase(c) real part (d) imagimq part
![Page 26: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/26.jpg)
3.0 MATHEMATICAL MODEL OF ANTENNA PERFORMANCE.—
The antenna is modeled by either a triangular loop or a semielliptical loop as illustrated in Figs. 6●
and 7,and the Cartesian coordinate system shown there is used throughout this section. Note
that the antenna is located in the plane xy, with the three vertices at &b, O,O)and (O,h, O),
respectively. To determine the current our model does not differentiate between the two
geometries. On the other hand the precise geome~ is used when calculating fie~ds.
3.1 Current Calculation - Perfectly Conducting Ground
At fnst let’s assume that the ground is perfectly conducting. Then an image loop can be
considered with the current flowing in the directions indicated in Fig. 13. For simplicity the
loading impedance is assumed to be distributed uniformly along the antenna legs only; the value
of the impedance per unit length ZL is arrived at by using the foIlowing simple approach
z~(co)=N1Z43((D)+N2Z77(CI))
2L(9)
where Z43 and 277 are the impedances of a single ferrite bead for material #43 and material #77,
respectively, presented in Figs. 10 and 11 of Sec. 2.3, and L is the antenna leg given by
(h* + b2)1/2. Additionally, NI and N2 are the total numbers of such beads. Note that the model
assumes that the distribution is along the antenna legs only and not along the base, This
approximation rests on the fact that the base is very close to the ground so that in this model its
current is neutralized by the correspondent image, as shown in Fig. 13, and the loop is reduced to
a rhombus. Furthermore, the load provided by the material #77 beads is effective only at
relatively low frequencies, say below a few MHz, above which the impedance becomes much
smaller than that of material #43. Since the antenna is elecmically small at low lkquency, and
the current does not change significantly along the loop, it does not matter where precisely the
impedance load is located, for the attenuation introduced by the load will be roughly equally
effective at suppressing the flow of cument horn one leg back to the other.
Under the above conditions, it has been shown [4] that for thin loops the Longitudinal current Is
satisfies the following equation
(lo)
26
![Page 27: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/27.jpg)
- ------ ------ ------ -----%, /
\\\\ //”\\\ /“”\ /\ ‘u” \ leg
(a)image
I
S = 2L/
●
s=3L
(5)
Figure 13. Geomerncal rncdel for the antenna describing the direction of the flow of current.(a) both real lmp and image are shown.(b) loop effectively usd in calculations (conrnbution from section on the ground is
ecancelled by its image).
27
![Page 28: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/28.jpg)
where k=2@k is the wave number, s is the arc along the loop starting at x = b, y = O (see Fig. 13),
VOis the source or the image strength in V/m, and
[()2L60.h —
Zc=m
I-601n(kr)L.
2kL<1—-
2kL>1
n
A time dependence e-i~t has been assumed throughout this chapter.
The boundary conditions for this problem are
I~(2L-) = IJ2L+), I~(4L-) = IJO+)
JJ2 ikvo~I~ds = — for both source and image
Zcacrossgap
Introducing
the solution is
{
Ae7(s-L) + Be-Y(s-L)
1S(s) =BeY(S-L)+ Ae-Y(s-L)
with
(X>o,y>o)
(X<o,y>o)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
Such current flows in the direction shown in Fig. 13, which is defined as the positive direction,
The image is obtained by considering the symmetry about the plane z = O.
From Eq. (14) one obtains for the velocity of propagation
28
![Page 29: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/29.jpg)
0 ‘=-cc”s{im’n[u::~;(18)
Since the velocity v is lower than the speed of light in a vacuum, the wavelength Z = v/f is lower
than its correspondent in free space by the same amount. Because the antenna resonances occur
when the length is an integer multiple of the wavelength in the medium, as a consequence of
loading they are shifted to lower frequencies, In fact, for the f~st resonance one obtains
f,= &oOkHz(19)
Without loading it would be
f’r=:” 1.7 MHz4L (20)
3.2 Current Calculation - Lossy Ground Accounted For
A second alternative model was derived by assuming that the cable at the base of the triangle and
ethe earth form a (lossy) transmission line, loaded periodically with ferrite beads, as shown
schematically in Fig. 14. The effect of such transmission line on each antenna leg can be
modeled as one lumped impedance positioned at x = ~b, y = O,resulting horn the cumulativeeffect of the toroids and the length of transmission line, and calculated acording to the recursive
relationship
Z(p + 1) = z(p)+ 277
Z(p – I)coshygv(p) - Zg s~hygv(p)z(p) = Zg
Zg coshygv(p) - Z(P - l)sinhygv(p)
z(o)= o
where v(p) is the separation between two ferrite material #77 beads, p is an integer varying
between 1 and N~2 with v(l)= //2, v(p)= t P>Z ~d
‘g ()=601n ~ Hr
(21)
(22)
7g =ikH
(23)
(24)
29
![Page 30: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/30.jpg)
.
part of antenna lying on the ground
at
/69
earth
Z=o
Figure 14. Model introduced to account for the presence of h real ground and the distributionof low frequency ferrite beads. -(a) “transmission line” formed between antenna coaxial cable and ground, loaded
periodically with #77 ferntes(b) the effect of such section of line is a lumped impedance at the points A,A’.
30
![Page 31: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/31.jpg)
(25)
are the characteristic impedance and propagation constant of the transmission line formed
between the outer conductor of the antenna cable (of radius r) and the lossy gound (ground
conductivity cg), the distance between the two being ~, along the antenna base.
To solve for the current, the differential equation .of Eq. (10) must still be satisfied with
ZL = ‘~~3 and with the following boundary condition, instead of Eq. (12).
(26)Z(N2 / 2) IJO+) = ZTIJO+) = V(C)+)
Z(N2 / 2)I~(2L-) = ZTI~(2L-) = V(2L-)
The solution is formally simkr to Eq. (15), but with A and B replaced by
-ikvor~ ~+2yLAf=w% 1+rLe+2~
● B–A’ ~-z%1=_rL
(27)
(28)
(29)
ZT - Zc“ withrL=— being the reflection coefficient at the end of the legs, as indicated in Fig. 14.ZT + Zc
Note that the image of the antenna legs is still considered in this approximation, and,
additiomdly, the properties of the ground are accounted for in determining the effect of the ferrite
loading along the base.
3.3 Potentials And Fields
Once the current is known one can calculate the vector and scalar potentials everywhere in space
by using
eikwlh I(x’, Y’)- dsx(x, y, z) = ---J
s(30)
31
![Page 32: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/32.jpg)
.
$(x, y,z) = *JP(X’!Y’)- ds
s (31) ●such that io)p = V“ 1. From Eqs. (23) and (24) [7–7’1= (X– X’)2-i-(y – y’)2 i-z2 , where the
primed coordinates indicate the source point and the unprimed coordinates indicate the
observation point, and the integration is performed along the loop (antenna plus image) whose
infinitesimal arc is indicated with X.
From Eqs. (30) and(31) thewlectrornagnetic fields can be obtained as
~=i&-V@
and
S=vxx
For our particular geometry the explicit expressions of the field components are
(32)
(33)
E,24
= icoAV–—av
where v indicates the generic Cartesim component x, y or z and
‘aAy , B = aAx aAy aAxBx=— —, BZ=—– —
az y a2 ax ay
The two Cartesian components of the potential A for the triangular loop are obtained as
‘0 bI (s)(exl + ex2 – ex3 – ex4) dx’Ax(x,y,z) = ---J. s
Po b~ (S)(–exl + f=2Ay(x,y, z) = ~~o ~ – exs + exA) tanfl dx’
where 6 = arctan Mb.
In Eqs, (36) and (37) form= 1,,.,4 it is defined
ex ~ = exp(iksqm ) / sqm
sq~ = (X - nmx’)2 -1-(y - rm[h - x’tan0])2 + 22
(34)
●
(35)
(36)
(37)
(38)
(39)
32
![Page 33: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/33.jpg)
and
{
+1 m=l,3
{
+1 m = 1,2nm =
-1 m=2,4 ‘m= -1 m= 3,4
The derivatives of AX,AY,and @necessary to c~culate ~. (35)
found as
(40)
and(36)have been explicitly
i3AX
{‘v(ik--&)+ex~w(ik -L)Is(s) cIx’” exl —W1 sq2 S42
~v(&-&-ex~EJ(~-~-ex3 —sq3 } (41)
The terms Fmv in Eq, (41) stand for
Flx=Fjx=x-x’
~x=F4x=x+x’
~y=~y=y-h+x’tane
~y=F4y=y+h-x’tan0
(42)
@
Fmz = z Vm
Note that aA ~ / A can be found from Eq. (41) by changing the signs of the products containing
exl and ex4, and multiplying by tan (1.
Concerning the derivative of the scalar potential ~, we found
-ex3 ~ (ik-+)+ex~~ (ik-L)W3 Sqd Sqd } (43)
Alternatively, for the elliptical geomemy, by letting x’ = a COSV’,y’ = a’ sinv’, we obtained
‘0 bIs(s) (exl + exz - ex3Ax(x, y,z) = —J v–exd) l–cos v/~. dx’ (44)
4~ o
‘o bIs(s)(–exl + exz – exs + exd)AY(X,Y,Z) = ---J. :~-”dx’ (45)
Q With the expression in Eq. (39) changed as
33
![Page 34: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/34.jpg)
Wm = (x - nmacosv’)2 + (y – rma’sinv’)2 + Z2
fi’(jk_L)_ex3EN(ik1+exz — - —)- ex~ %lc-1)Sqz Sqz W3 sq3 sq4 sq4 }
In Eq. (42) the following changes need to be made
~x= %x = x-acosv’
F2X= F4X= x + a cosv’
Qy=F2y= y-a’sinv’
~y = F4y = y+a’sinv’
, where v’ is related to the arc lengths of the ellipse by
s(v) = aJ~’2~’ dv’
and <0 = l/~1-(a’/a)2.
34
.
(46)
●
(47)
(48)
(49)
(50)
![Page 35: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/35.jpg)
4.0COMPARISON BETWEEN MEASUREMENTS AND CALCULATIONS
4.1 Available Measurements
This concept was fust demonshated at Kirtland in November 1990, in the triangular geometry,
using the existing Achilles HI poles as support s&uctMe. The scheme of the instmmentation set
up is illustrated in Fig. 5. The signal from the 3577 Network analyzer is transmitted through
coaxial cable and fed fust to a power splitter, then to a 46 dB (nominal) power amplifier and
finally connected to the 7/8” Heliax cable constituting the FFCW illuminator. me output of the
power splitter was connected back to the reference input of the network analyzer via a fiber optic
link. Therefore the reference measurement is the voltage corresponding to the power at the
section immediately after the power splitter. For the elliptical conilguration the power splitter
was placed at the RF output of the network analyzer and therefo~ no fiber optic link was
employed to connect its output back to the network analyzer reference channel.
A representative set of test point coordinates used for the field map of both antenna geometries is
illustrated in Table 1. They are used to establish the comparisons with the values calculated with
the models of Sec. 3. The field sensors were MGL-2, MGL-5 and ACD-4 for the measurements
of B and D, respectively, in the triangular geometry, whereas ACD- 10 sensors were used for the
elliptical geometry, instead of ACD-4S. Additionally, for the triangular configuration, the
current was measured at four symrnernc locations, two along the antenna legs and two along the
base, all quite close to the ground. For practical purposes the coordinates of these points are
&39, O,O)and &l, O,0). An SCP-1 current probe was used for these measurements.
4.2 Antenna Properties And Field Characteristics
4.2.1 Triangular Geometry
The first issue to be addressed is the determination of the radiated power, from the knowledge of
the field levels. In the fwst demonstration test at Kirtland no measurement of antenna input
impedance, or equivalently, input reflection coefficient was made. One can therefore only make
a guess at what the incident power might have been by knowing its value after the power splitter
from the reference measurement V~,and multiplying it by the gain provided by the amplifier.
Assuming that the 10SSalong the cable connecting the amplifier output to the antenna gap is
negligible it turns out that the incident power at low frequency can be estimated to have been Pin
- 5W. At higher frequencies the cable connecting the 3577 to the power splitter introduces
losses and the incident power is reduced to -1 .6W. However the exent of the reflection at the
35
![Page 36: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/36.jpg)
Table 1.
Measured fields
BX BY BZ EX EY EZ
(T) (C/m2)
~ 0,0,0 x~ 0,0,-2~
x
80,0,20 x
u 20,0,20 xE.*2 0,3,20 x x x x x xw3 0,3,40 x x x x x x+
-20,3,20 x x x x x x
Note: (1) (O,O,-2)was used for the triangukr configuration; (O,O,O)was used for theelliptical one
(2) (O,3, 40) was used for the triangular configuration only
(3) the height above the ~ound was 3.3 m instead of 3m for the elliptical configuration
36
![Page 37: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/37.jpg)
antenna gap is not known. To this purpose the mathematical model illustrated in Section 3 can
● be usefully employed to estimate what the radiated power might have been by calculating the
fields at the available test points. Starting with Eq. (15) and in all the following field expressions
it is notal that the current and field levels depend on the value V. of the source strength, which
can be expressed as
[12 Pra~lZil?2 1/2
V.=re{Zi]
(51)
where ~ is the input impedance at the antenna gap and pmd is the transmitted power, also at the
antenna gap. In the absence of any measurements for Zi, this was estimated by using the current
of Eq. (15) itself, i.e. by taking VW and then the parallel combination with the 50 Q resistor was
calculated. By numerically fitting the calculations with a constant value of pmd which gives the
best agreement with the measurements, it was found that abut 0.1 W was actually radiated by
the antenna.
Figures 15 through 20 illustrate the comparison between measurements and calculations, and the
model of Sees. 3.1 and 3.3 is shown to be a good estimator over the entire frequency range of
interest, Note that the current is modeled as though the loop has four legs, two actual ones and
two images, and no portion of it were running along the ground. To calculate the current we
assume that both species of toroids were distributed along the antenna legs resulting in a uniform
impedance per unit length and also that the radiated power is constant, From Fig. 20b one can
see that there is very good agreement up to 100 MHz and beyond that the measured current falls
below the calculated one, perhaps because the radiated power drops. However the discrepancy
might be due to some extent to the measurement set up.
On the other hand the model of Sec. 3.2 for the current does not give an equally good agreement
between measured and caculated fields. For this reason we report, as an example, only the
comparison at the test point (O,3, 20), illustrated in Fig. 21. Various reasons could account for
the discrepancy; for instance it is difficult to specify the line parameters for the section of
transmission line above the ground and, additionally, the inclusion of the image in this case is no
longer completely justified. However, note that the disagreement is not very drastic and is
limited to frequencies below 10 MHz. Above that point the agreement is just as good as with the
other model. It must also be remembered that the measured data are themselves not very reliable
at low frequencies because of the small values of the derivative signals measured by the sensors.
● Such values could be in the noise of the network analyzer.
37
![Page 38: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/38.jpg)
>\
\
lo-io=
lo-ii=
10-12= F
\
10-13 z
Figure 15a.
10-14 # , I ,tI1,1 I I I #,,III I n 1 ,1I,
105 106 17’
Freq (Hz;”
10-9 , v 1 I , , , I n , 1 1 , , 1 1, 1 , 1 u 1 z m
+ ‘\
/b
-..-1 /
10-’0,-
,..,/ ,!,?,,::)”!%,:j~!*.JFreq (Hz\O
Calc.——— —— Mess. “
Triangular Geometry
Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (O,3, 20). The logarithmic fi-equcncyscale emphasizes the low frequencies.
![Page 39: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/39.jpg)
.-l
(0, 3, 20110-12‘ I ‘z(w
0.0 5. OE-I-07 1. OEi-0F3 1. 5E+OB 2.0E+08Freq (Hz)m
‘o-’’r–”-----~
●✎
-4
(0, 3, 20) By (T)10-’1 , , ,
0.0 5.0E+07 1.0E+08 1.5E+08 2.0E+08Freq (Hz)
Calc.—.— —— Mess.
Triangular Geometry
,o-14LJE__.u”’‘x(c’m:)__.1“-1””‘mphmizestietighfiiinci:sComparison between model calculations (Sees. 3.1 and 3.3)and measurements at (O 3 20) The linear frequency scale
0.0 5. OE-I-07 1. OE+OB 1. 5E+08 2. OEi-0f3Freq (Hz)
![Page 40: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/40.jpg)
10-9 L , 1 r a , , , I 1 , , , r 1 9 I m1 n 1 , , 1 , #-
:-fl /,/, nfi
L\ Mf \/
10-10 \ ~ v
L- 11 1
1(-20, 3, 20) B, (T)
\l 1
—
lo-:;&--- ‘ ‘ ‘;$ # t , * I 9 EL 1 , , , , t
lo~ 10—-&0 Freq (Hz)
,O-fi[WV:,;:) ,.BtdT!i,,...,710
Freq (Hz;” .
Calc.———— . Mcas.
Triangular Geometry
lo-ii
10-12 #\
\
lo-~a~ \
io-i4z
Figure 16a. Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (-20, 3, 20). The logarithmic frequency
io-i5!$_ R , I ,11*II t , 1 t ,,t11 scale emphasizes the low frequencies.10 106
Freq (Hz!”
![Page 41: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/41.jpg)
10-10
L- .-2_!L-_-l(-20, 3, 20)10-11
10-9 p—————— , ‘~
10-[
10
1- 4
L-(-20, 3, 20) By (T)10-11 —— ,
$=. 0.0 5.0E+07 1.0E+08 1.5E+08 2.0E+08 0.0 5. OE+07 1. OE+OB 1.5E+OB 2.0E+08Freq (Hz) Freq [Hz)
10-11 —— -——-—- --—--- —--3
10-’
10-’
10-14
40-’5
Calc.~———— — Mcas.
Triangular Geometry ‘
~ .-iw51L-l‘iw”b”‘mphasizesfielOw@uenc’~s
Comparison between model calculations (Sees. 3.1 and 3.3)
(-20, 3, 20) and measurements at (-20, 3, 20). The linear frequency scale
——.— .. . . .0.0 5.0E+07 I. OE+OEI i . 5E+OB 2. OE+OB
Freq (Hz)
![Page 42: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/42.jpg)
“-ii~1- -1
~-+\
10-’2> / \
=\ /
10-13=
10-’4 I , , ,
105
, 1 t 1 , I t f , , t 1 t t 1
106 107 104-P Freq (Hz)N
1- -/
F(-20, 3, 20) D,, (c/m2)
lo-i4&----‘ ‘ “’’”Y
I t , , t , , LI , , , 1 , #
10 106 10Freq (Hz;”
Calc.—.. —— Mess.
Triangular Geometry
Figure 17a. Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (-20, 3, 20). The logarithmic fkquencyscale emphasizes the low frequencies.
Freq (Hz)
![Page 43: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/43.jpg)
.
lo-ii~ I 1
.
L--l(-20, 3, 20) Dz (C/m2)10-14 ,
1- -1
- (-20, 3, 20)10-14 t ‘y “a
0.0 5.0E+07 1.0E+08 1. 5E+OB 2.0 E+O13 0.0 5.0E+07 1.0E+08 1.5 E+O13 2. OE+OB
z Freq (Hz) Freq (Hz)
10-9
F—, -————
>
10-10
lo-iiL , , n
Figure 17b.
Calc.——.—— Mess.
Triangular Geometry
Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (-20, 3, 20). The linear frequency scaleemphasizes the low frequencies.
0.0 5.OE+07 i.0E+08 1.5E+08 2.OE-I-013Freq (Hz)
![Page 44: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/44.jpg)
10-9 , t 1, 1 , I T 10-9 L\
1 T #, , 1I I \ , I ,
-\\ k
\\ 10-10 = J/.— \
10-’0;-+
\
10-” z
(0, 3, 40) Bz (T) (0, 3, 40) By (T)lo-ii , , t,
105I , t I
106
, !7
t , , , 1- lo-i2 ,1OB
1 , ,t I t t t t, ,,1 ! , ,0 t
Freq (Hz!”105
6 b*
10 10* Freq (Hzt”
lo-i’h , 1I 1 1 , t , 4 1 , , Y Calc..———— Mess.
Triangular Geometry
10-” , \
10-’4?
Figure 18a. Comparison between model calculations (Sees. 3.1 arid 3.3)
10-’5and measurements at (O,3, 40). The logarithmic frequency
1ok
* t 1 ,,I1I
106
, , t, ,I t , , , scale emphasizes the low tkquencies.
Freq (Hz~Olob
● ✎ ✎
![Page 45: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/45.jpg)
a-Q
‘0“r——––——- 3
t- -1
I (0, 3, 40) B. (T)L10-121 , , , I
0.0 5.0E+07 1.0 E+OF3 1. 5E+08 2.0E+08b Freq (Hz)
10-’1 —---
r
,
‘7
10-13
3
(0, 3, 40) By (T)10-’2 , t ,
0.0 5.0E+07 1.0E+08 1.5E+08 2.OEFreq (Hz)
Calc.————. Mess.
Triangular Geometry
l___ D1(c/m:] ~ ‘im18b.(0, 3, 40) ~Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (O,3, 40). The linear frequency scale
10-’5emphasizes the low frequencies.,
0.0 5.0E+07 1. 0E+08 1. 5E+O13 2.0 E+Ot3Freq (Hz)
![Page 46: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/46.jpg)
i1- -ir\\
\
i10-9
io-io , 1 t t , , t I I t , , , t 1 , , I , , , I , 1 11
105 106Frea (Hzj”
10-8 ~ , % , 11 I , , I 1 , B , , ,
\
10+ ‘7 I“\
i\
d 1],1 Figure 19a.f
[8, o, -2) B= (T)10-10
J’
, * , * , , II 1 t I * , * 111 # t , t # 1 Lio6 107 Ii?
io-e
r“’’’’”“’’”\\\10-9 z“ \
\
6
10-10t ,
10$
t , t tn[t,( , t # , f
106Fr’eq (Hz)
Calc.——— —— Mess.
Elliptical Geometry
Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (20, O,20), (O,O,20), and (O,O,-2).The logarithmic frequency scale emphasizes the lowfrequencies.
-—Freq (Hz)
![Page 47: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/47.jpg)
●40-8 , , ,
10-9L
o10-8
10-9
0
G10-B
10-9
.0 5.0E+07 1.. OE+O8 1.5E+08 2.0 E+O13 0.0 5.0E+07 1.0E+08 1.5E+08 2.0 E+O13Freq (Hz) Freq (Hz)
———— ,Calc.
.—— .— Mess.
Triangular Geometry
J%d”.* * . % J.*h~*@*Jt#f v%4*b+,;
iT
.
Figure 19b. Comparison between model calculations (Sees. 3.1 and 3.3)
(00 01-21 Bz (T)and measurements at (20, O,20), (O,O,20), and (O,O,-20).The linear Iiequency scale emphasizes the low frequencies.
10-10 I 1 I
0.0 5. OE+07 1, OE+O13 1. 5E+OEI 2. OE+08Freq (Hz)
![Page 48: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/48.jpg)
.bm
1
0° I 1 I I 11I I I 1 1 i I I 1I 11 1 i I 1I I 1 I
calculation
;N’
mess. at (fl, 20, O)
‘\
.<+==--
\ \
o–1
Current at (*1, 20, O) (A)
o–2 I I 1 I I I I I I I I I 1 I I 1 { I I r I 1! I 1I105 106 107 10°
Freq (1---Iz)Figure20a. Comparison between model calculations (Sees. 3.1 and 3.3)
andmeasurements at(l,20,0). ‘l%elogarithmi cfrequencyscale emphasizes the low frequencies.
![Page 49: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/49.jpg)
10-2
I I I
mess. at (-1, 20, O) -
\
\\
Imess. at (+1, 20, O)
Current at (*1, 20, O) (A)
1 I I
0.0 5.0E+07 1.0E+08
Freq (Hz)1. 5E+08 2.0E+08
Figure 20b. Comparison between model calculations (Sees. 3.1 and 3.3)andmeasurements at(l,20,0). l’helinea rfrequencyscaleemphasizes the high frequencies.
![Page 50: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/50.jpg)
Wo
10-8 g , , ‘
10-g
- “\,’10-’0 .
lo-i’ .E
1 (o, 3, 20) az (T)lo -~— ‘lo-i2
n I # 1mt*1 1 t , ,,11
Iof 10bFreq (tiz)
‘O-’F------‘mt-
lo-i2=
.
‘\___--”-.
)’/10-’3 : 1/\l
/
\1
()(3, 20) Dx (C/m2)lo-i4 [ 1 I cI , *,I I 1 , , t %t,I
10s 106Freq (Hz!”
10-9
10-’0
lo-ii
I (0, 3, 20)10-12 -+’- ~ 5Y’T d
10Freq (Hzj”
Calc.——— —— Mess.
Triangular Geometry
Figure 21a. Comparison between model calculations (Sees. 3.2 and 3.3)and measurements at (O,3, 20). The logarithmic fi-equencyscale emphasizes the low fkquencies.
![Page 51: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/51.jpg)
,.-12- ‘z ‘T)t .-!--.-l0.0 5. OE+07 i.oE+08 1. 5E+OE 2. OE+OEI
U-I+ Freq (Hz)
@%----1
L -1
lo-ii
Lt-(0, 3, 20) By (T)io-i2
0.0 5. OE+07 1. OE+08 1. 5E+OF3 2.OEFreq (Hz)
Calc..—. —— Mess.
Triangular Geometry
+-OH
L * --_-_lFigure 21b. Comparison between model calculations (Sees. 3.2 and 3.3)
(0, 3, 20) Dx (C/m2)and measurements (O,3, 20). The linear fkequency scale
10-’4emphasizes the high frequencies.
0.0 5. OE+07 ~.0E+Ot3 1. 5E+08 2. OE-I-09Freq (Hz)
![Page 52: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/52.jpg)
Itis pointed out that the antenna response is quite smooth at points on (or very near) the ground,
as shown in Fig. 19, excluding the small residual resonant behavior exhibited at frequencies
below 10 MHz. This is caused by the limitations of the ferrite loading to provide for a complete
damping of the fmt few resonances. On the other hand, at points above the ground both
measurements and calculations exhibit an interference pattern with repetitions of broad maxima
and sharp nulls, whose location and periodicity, in frequency, depend on the coordinates of the
test point itself. To explain such behavior for the point (O,3, 20), chosen as an example, one can
refer to the sketch of Fig. 22 which illustrates the paths of interference between a plane wave
originating at the source (O,20, O)and propagating towards P in the direction identified by &
and a plane ave originating at the image point (O,-20, O),and propagating along the direction
given by kimw Note that the plane of the figure is perpendicular to that containing the antenna
and passes through its center. The path difference A between the two rays is, for this specific
case, 4.23 m. Such length becomes equal to one half of a wavelength in air at a frequency very
close to 35 MHz. Hence, considering that the electromagnetic field components at the source
and image are related in the following way
DXsource= -Dx image
BYsource= -BY image
BZsource= Bz image
it is clear that DXand B~ start off with 180° phase difference between source and image, whereas
Bz has the same phase, At a frequency very close to 35 MHz an additional 180° is added and so
there is a constructive interference (maximum) for DXand BYand a destructive interference for
Bz, resulting in a minimum. The period of repetition of the pattern is --70 MHz, which
corresponds to A being equal to one wavelength.
It is stressed that the fields presented here are total fields, i.e. they include incident and ground
reflected components. To fairly evaluate the antenna characteristics, one should look at incident
fields only. In fact, the knowledge of the incident field is needed to perform an extrapolation
process of the responses induced inside a system by some kind of threat, since threat fields are
usually defined as incident fields. Therefore, simulators such as the antenna under investigation
here should be designed and evaluated for their ability to generate an incident field which is as
close as possibIe to that of a uniform plane wave in a predefine volume. To this effect we
evaluated the incident field at the point (O,3, 20) by not including the ground reflected
contribution in our model and the results are presented in Fig. 23. Itis shown that the
interference pattern has been eliminated, as expected, and only the effect of the fust few antenna
resonances is visible. At frequencies above 10 MHz the field is flat since all the resonances at
52
![Page 53: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/53.jpg)
c.7-ti
AIY
B
26.24 m
(0,3,20)
4-Z 4
30.47 m
Figure 22. Scheme of interference of incident and reflected field components at (O,3, 20).
![Page 54: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/54.jpg)
10-9
10-”k[0, 3, 201 B, (T)
lo-i2 , t 1 t , I 1I J , , ,*I , , , , ,m 105 10 10b.b Freq (Hz!”
lo-i’~ ,, , I , I , , I , , I Y
(o, 3, 20] Dx (C/m2)io-i4
10s
* , , *, ,I 1 , ,, I t , ,t,A
1067
#
10Freq (Hzj”
t
(o, 3, 20) By (T)Io-ti
10*, , * , , , ,#[ , , t
106I # , , ,
12Freq (Hz~O
Figure 23a.
Calc.——— —. Mcas,
Comparison between measured total field and calculatedincident field at (O,3, 20). The logarithmic frequency scaleemphasizes the low frequencies.
![Page 55: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/55.jpg)
10-’E-----------%
m 0.0 5.0E+07 1.0E+08 1. 5Ei-OB 2. OEi-08Freq [Hz)
a .
,o-J.__!_v2E!_‘y ‘T’ ,
~Figure 23b.
(o, 3, 20) Dx (C/m2 )lo-i4’ , * t
0-0 5. OE+07 1. OE+Of3 1.5 E+Of3 2.0E+08Freq (Hz)
— —
0.0 5.0E+07 1.0E+Of3 i.5E+08 2.OE+OBFreq (Hz)
Calc.——— —— Mess.
Comparison bctwccn measured total field and calculatedincident field at (O,3, 20). TIE linear frequency scaleemphasizes the high fivqucncics.
![Page 56: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/56.jpg)
high frequencies are completely damped by the ferrite load. Note that the incident DXand BYat
frequencies below 10 MHz are higher than the total fields, whereas Bz is lower (in the same
frequency range) consistently with the model of interference and the sign relationship described
in the paragraph above,
4.2.2Elliptical Geometry
For the elliptical geometry the input impedance was obtained through measurements of the
reflection coefficient at the section where the coaxial cable is cut open. Since the network
analyzer measures the reflection coefficient at an internal instrument interface, to obtain the
value at the desired antenna gap one needs to take, in addition, a measurement of the portion of
cable between the instrument and the wanted interface, configured as an open circuit. The ratio
of reflection coefficients thus transfers the measurement to the antema gap.
Two configurations were considred; in the fiist one the antenna leg fed by the network analyzer
had its inner conductor directly attached to the outer conductor of the second leg at the gap, in the
second configuration a resistor was added between the center and outer conductor of the antenna
fmt leg to reduce the mismatch. The resulting input impedance for both cases is illustrated in
Figs. 24-25. Note the behavior of the impedance in the case there is no resistor: due to the
resonances of the loop (the fust appem around 450 kHz) the impedance varies substantially,
particularly around 1 MHz. This is attributed to the characteristic of the #77 material ferrite
toroids which exhibit a resonance at around 1 MHz that coincides with a loop resonance. The
impedance gradually decays above 10 MHz, and the rate of decay changes with ferrite loading.
It appears clear that when a 50 Q resistor is added in pamllel, the overall input impedance is
lowered at frequencies below 50 MHz, while above the parallel arrangement introduces a
resonance around 100 MHz. In this case the total impedance becomes inductive at high
frequencies, whereas in the absence of the parallel resistor the impedance was slightly capacitive.
EvidentIy the 50 Q resistor is not just a pure resistor at high frequencies but has some reactance
as well. In fact, by modeling the 50 Q resistor at high frequencies as an impedance RI + jcoL1,
and placing this in parallel with the antenna impedance R + l/jcoC, it can easily be shown that
there is a value of frequency at which resonance occurs, i.e. the imaginary part of the total
impedance is zero. Such value is
(52)
56
![Page 57: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/57.jpg)
G 103
224anscsil 50X (i+sii) / w-sii)’
k “’’”’’” “m’”’’’” “’’””’u’ “’”7Magnitude
,02 ~io5 106 107 ion 10sm
2BO0.0
i400.o
c 0.0
-i400.0
-2000.0
1(
Frea [Hz)
I I I n
1 i , c , 1 .,..1 I
f
Lull , , , u
io67 106 i
Fre~” (Hz)
98.0
49.0
0.0
-49.0
-98.01(
6.E+03
3000.0
q 0.0
/
-3000.0
1 1 I TT
Phase in Deg.
v
* # , , * ,**1 , # , * ,,s1 * , ,,, ,1 , ,&J\ 106 7 ioa io”
fre~” (Hz)
-6.Ei-03 , , UJll , # ~~.t , , , s*t , ,i-j
ios 106 107 ion iogFrea [Hz)
Figure 24. Input impedance for loop of elliptical geometry (Fig. 7). No matching resistor used here (Baseline configuration).
![Page 58: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/58.jpg)
u-lm
G
103
102
223an50sli 50*(i+sll)/(1-sll)
1- 9 I I -
Magnitude
~
105 106 10° 109Fre;” (Hz)
GI
200.0
100.0
-100.0
-200.0Ic
ITReal
1 r.,,., 1 m
t , t * , ,.1 , tI 1 , UJ
10= 7 ion 1’Fre:O (Hz)
1
74.0
37.0
W3ogan 0,0
%
-37.0
GI
75.0
1 -+W..., m l-n
Phase in Deg.
, ,..1 ,
I 9..LUL * t105 7 10° 109
Fre~” (Hz)
Imag150.01
[
h-_:7 “’”.
-150.0 .~105 105
7 ion 109Fre~O (Hz)
Figure 25. Antenna input impedance when a 50 Q resistor is placed in parallel, according to Fig. 7. (Baseline configuration, elliptical
![Page 59: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/59.jpg)
‘
i This problem can be mitigated by using shorter lead lengths or a parallel combination of
e esistors.
The comparisons for the semi elliptical loop are reported in Figs, 26-29, and the chosen set of
measured points closely resembles that used for the triangular shape. The overall agreement
between measurements and calculations is very similar to that obtained for the other geometry
and similar considerations can be made to explain the features of the fields,
59
![Page 60: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/60.jpg)
10-9r‘“”—-”~
10-12
10-i3 ~,
\\
/
10-14
3
= (o, 3.3, 20) Dx (C/m2 )10-i5 I , t I , f , , , 1 , , , , , I t —-L--L. J
105 10= 107 10°
io-g
E_‘ “’’’’” ‘“m
t (0s 3.31 20) By (T)’12L
10 ———————J—JJ.J..JQL——~~
1.05 106 107 108Frea (Hz)
Calc.————— Mcas. ‘
Elliptical Geometry
Figure 26a. Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (O,3.3, 20). The logarithmic frequencyscale emphasizes the low frequencies.
![Page 61: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/61.jpg)
FL u —.——
?---.—_—T____ —-——-—--
=1
t_(0, 3.3, 20) B= (T)
-i.210 —_–_.-._-L_—— —..-.t 10.0
1
●✎
.LU
F——., “—————-–—~—----
t 7
10-10
10–ii
.—.5.00E+07 1.00 E+Of3 1. 50E+08 2. 00E+08
L(0, 3.3, 20) By (T)10-12
.—-.--.--L----- —- —.__L__________ t _ A
Frea [Hz)o-l+ 10-11
E
—–—--—-—.—---—___________ , .-—...--—.—— ———-.
11- -i
10-12
10-i3
~o-14
Figure 26b.i-
lo-J_Eu!iY!-_ ~ ‘x“’m’)d
0.0 5.00E+07 1.00E+08 1.50 E+OEI 2.00 E-I-09
Calc.————— Mcas.
Elliptical Geometry
Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (O,3.3, 20). The linear frequency scaleemphasizes the high frequencies.
0.0 5.00E+07 i . 00 E-I-013 i.50E+O13 2.00 E+Of3Frea [Hz)
![Page 62: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/62.jpg)
1o-g
[ ‘“’’’’”‘“’’’’”\ 7-lo \
10
10-11 \l
I
- (-2o, 3.3, 20) B, (T)10-!.2———~A~--- 1 t-
105 106 f.07 IoemP.) Frea (Hz)
10 -11
F----l—-~-~”—— ‘ ‘ ‘ ‘ ‘ ‘
I .-410-12
(’b10-f.3‘
// A~%wq\ \/\ 0=---\ I
10-14 \gf
/’10-1.5
t , 1 ~J: (-20, 3.3, 20) Dx (C/m2)
10-i6105 105 107 10B
Frea (Hz)
10-9
r’ “’’’’”‘“’’’’”‘‘7\
\\\\
10-io
l\\ f
‘\ //\
\,/ J,Q-iiid~fJ‘1{\
# ., ) By (T)———L——A—
io5 106 107 108Frea (Hz)
CalC.————— Mcas.
Figure 27a,
Elliptical Geometry
Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (-20, 3.3, 20). The logarithmicfrequency scale emphasizes the low frequencies.
.
![Page 63: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/63.jpg)
.
mw
m e10-g
T.———--——-—————
110-9 ------------r ——l—————
—— .—-.-—,
1-ii-’ I
~ (-20, 3.3, 20) Bz (T)10–12L–––—L______ —.~~. -l
0.0Frea [Hz)
-if10 -–—-.—----.-—
E--r--. —---——..__ ———-._-..—
7
1- -4
●✞✎
5. OOE+-07 1.00E+08 1. 50E+08 2.00E+08 O .0
10-i5
L “i
Figure 27b.
(-20, 3.3, 20) Dx (C/m2)~o-i6 ..~ —.—...—...~———L—.—. . . .
5.00E+07 1,00E+08 1
Frea (Hz)
Calc.————- Mess.
Elliptical Geometry
50E+08 2.00 E-I-08
between model calculations (Sees. 3.1 ~d 3.3)Comparisonand measurements at (-20, 3.3, 20). The linear frequencyscale emphasizes the low frequencies.
0.0 5.00E+07 1. 00 E+Of3 1. 50E+08 2. OOE+08Frea (Hz)
![Page 64: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/64.jpg)
10-i2I_ 1 1 * , 1, I 1 1 , , 1 1 ,
I “~
LIIII1lII 11[ t ~~~~~~~(-20, 3.3, 20) Dz (C/m2)
10-i5105 io6 to’ 108
m-P Frea (Hz)
t -4
L ~~~~~~~~Iltr[ltttu(-20, 3.3, 20) Dy (C/m210-15
105 106 107 10°Frea [Hz)
Calc._—— —— Mcas.
Elliptical Geometry
Figure 28a. Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (-20, 3.3, 20). The logarithmicfrequency scale emphasizes the low frequencies.
![Page 65: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/65.jpg)
●✌✎
.AU
10-i
10-i
10-i
0.0
. —— ... ..—..-———7—----- — ——----nq
1
(-20, 3.3, 20) D, (C/m2) 1
‘“ E–—------——”—’—’——..—.— — ---—
--3
L I __.._Ll(--20, 3.3, 20) Dy (C/m2)-1510 —.--– _J__.____.__——l_ .—_..—5.00E+07 1.00E-I-08 1.50E+08 2.00E+06
—–-..~-._—~——— ——–. --l5. OOE+07 1.00E+08 1.50 Ei-0i3 2.00 E-I-09 O .0
0-lm Frea (Hz)
10-9-- ———————— —.———.-..——— -–-—-—r—---------y
Frea (Hz)
Calc.————— Mess.
Elliptical Geometry
L(-20, 3.3, 20) 6X (T). i-1210 - .~—-l——. , .–__.i
Figure 28b. Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (-20, 3.3, 20). The linear frequencyscale emphasizes the low frequencies.
0.0 5.00E+07 i.00E+OEi 1.50E-I-08 2.00E-!-09Frea -(Hz)
![Page 66: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/66.jpg)
10-0
10-g
t 1L -1
I I
L(20, 0, 20) ‘ 1Bz (T) , ,,,,,,110 -io L._.~~
105 106 107 108‘a0’) Frea (Hz)
10-7
10-8
10-9
L [0, 0, o) Bz (T)10 -fo
.~ , t , , , 1 t 1 t , , t , I ,
105 106 107 108
10-8- , ,,1 I “~— 1 , , 1-
L-\
\\
\10-9-
l]
(0, 0, 20) Bz (T) j~o-iol , t , 1 , t 1 , t , t , , , 1 , , , 0
105 106 107 108Frea (Hz)
CAL-——. . Mcas.
Elliptical Geommy
Figure 29a. Comparison between model calculations (Sees. 3.1 and 3.3)and measurements at (20, O,20), (O,O,20), and (O,O,O). Thelogarithmic frequency scale emphasizes the low frequencies.
Frea (Hz)
a“., .
![Page 67: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/67.jpg)
L9
0 0 0 01 1rn Al
-11111 1 I i 111100
u-l
“o0ry
-n$7l-un-
.-0XoNIT--i-
0m
*in0m;m
ml“o0$1
~
6 0
“o
0
0 u-l
00m0
-0Xoly~UI
0m
N
0 0 0.l!
0
0II1II
u-i
-L
m0+-0XoNm-+ oal
ulom
&m
●m
![Page 68: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/68.jpg)
I
i
5.0DESIGNIMPROVEMENTS
The current choice of ferrite load provides a reasonable damping of the unwanted antenna
resonances but has drawbacks, particuhrly at low frequency, In fact the frequency dependent
ferrite impedance is very small at low frequencies because the inductance is very small and does
not provide sufficient load, since the ferrites are designed as low pass filters. Furthermore, the
impedance varies with frequency and is not completely controllable. Ideally, one would like to
have a constant resistance along the antenna, according to the discussion presented in Sec. 1
where an approach is outlined to accomplish”this goal. However materiaIs other than ferrites
must be used as magnetic cores so that at all frequencies of interest the core impedance is much
larger than that of the constant resistor which is inductively coupled to the antenna cable through
the core. Suitable materials have recently been identified and future efforts will be devoted to
improve the existing illuminator concept with a conholkxl resistive loading.
68
![Page 69: CLEARED - University of New Mexico](https://reader031.vdocuments.mx/reader031/viewer/2022020622/61ed617d9c38e53be40563b7/html5/thumbnails/69.jpg)
REFERENCES
[2]
[3]
[4]
[5]
[6]
[7]
[8]
●[9]
Zuffada, C. Yang, F.C. and Wong, I.: “On the Thin Toroidal And Elliptical Antennas,”Sensor and Simulation Note 315, January 1989. Also “Currents and Fields of ThinCircular And Elliptical Loops,” IEEE Transactions on EMC, Vol. 33, No.2, May 1991.
Baum, C.E. and Chang, H.: “Fields at The Center of a Full Circular TORUS And aVertically Oriented TORUS on a Perfectly Conducting Earth,” Sensor and SimulationNote 160, December 1972.
Baum, C.E,, Prather, W.D, and McLemore, D.P.: “Topology For Transmitting Low-Level Signals From Ground Level to Antenna Excitation Position in Hybrid EMPSimulators,” Sensor and Simulation Note 333, September 1991.
Baum, C,E.: “An Aniso~ophic Medium For High Wave Impedance,” Measurement Note39, May 1991.
Misner, C.W., Theme, K.S. and Wheeler: Gravitation, W.H. Freeman and Co., SanFrancisco, 1973.
Baum, C,E.: “A Spiral-Transmission-Line Technique For Detecting Slot Apetiures inShield Enclosures,” Measurement Note 37, December 1987.
Baum, C,E,: “Some Electromagnetic Considerations For a Rocket P1atfotm ForElec~omagnetic Sensors,” Sensor and Simulation Note 56, June 1968.
Baum, C.E.: “Some Considerations For Inductive Current Sensors,” Sensor AndSimulation Note 59, July 1968.
Darras, D., Zuffada, C., Marin, L. and Cheung, C.: “Achilles III Simulator FacilityDescription And Field-Map Set Up,” Achilles Memo 10, May 1988,
69