CAPTURING PHYSICAL PHENOMENA IN PARTICLE DYNAMICS
SIMULATIONS OF GRANULAR GOUGEEffects of Contact Laws, Particle Size
Distribution, and the 3rd Dimension
Julia K. MorganDepartment of Earth Science
Rice University
(http://terra.rice.edu/department/faculty/~morganj)
MOTIVATION
• Complicated macroscale processes (e.g., fault slip) commonly require phenomenological descriptions.
• Particle dynamics (PD) models, e.g., DEM, allow us to explore fundamental physics of the system - source of phenomenology.
• Controlled lab experiments provide intermediate validation points, bridging gap between PD models and whole earth simulations.
FAULT MECHANICS EXPERIMENTS
• Byerlee’s Law
• Rocks fracture and create gouge
• Slip localizes -> dynamic instabilities
• Rate-state friction – phenomenological, not physics-based.
• We still can’t predict earthquakes Fault structure
DISCRETE ELEMENT METHOD(Cundall and Strack, 1979)
Advantages of DEM:-Allows heterogeneous and discontinuous deformation.
System can evolve through time and space.- Can correlate behavior with physical properties and
mechanical state.-Constitutive behavior is a result, not an assumption.
Use DEM simulations to explore fundamental mechanics of fault gouge
PARTICLE SIZE DISTRIBUTION(Sammis et al., 1986, 1987)
Greater relative abundance of small particles --->
Experimental Configurations
PSD EFFECTS ON STRENGTH
Greater relative abundance of small particles --->
Strength drops to D=1.6 -> Slip weakening mechanism.No means for shear strength recovery.
WHY ARE SHEAR STRENGTHS LOW?Ease of particle rolling in 2D.
• PSD changes during granular shear result in second order decreases in strength, providing a means for slip weakening along fault zones.
• Rolling of particles in 2D system yields unreliable strength estimates.
EFFECT OF PARTICLE ROLLINGNumerically damp or restrict particle rolling
At high interparticle friction, rolling still dominates in 2D.Must fully restrict particle rolling ~ interlocking angular particles.
PARTICLE FRACTURE(Lang, Sparks, and Aharanov, in prep)
PARTICLE FRACTURE(Lang, Sparks, and Aharanov, in prep)
PSD’s for several run pairs, at 18 MPa (black) and 27 MPa (red), at 3 different strains. Systems shown by red-black pairs have experienced the same number of breakage events (25, 50 or 95).
PSD is basically the same for all systems with the same amount of damage, although they have been subjected to different stresses, and significantly different strains.
RATE-STATE FRICTION(e.g., Dieterich, 1979)
Fault friction depends on sliding velocity, V, and system “state”, (t, Dc).
CPU intensive calculation.
TIME-DEPENDENTCONTACT STRENGTHENING
(e.g., Dieterich, 1972; Beeler et al., 1994; Marone, 1998).
Friction depends on duration of contact, t, during static holds; drops to dynamic value
upon slip.
Simpler to implement numerically, and may reproduce rate-state phenomenology.
DEM MODELS W/ CONTACT HEALING
• Velocity-strengthening - steady-state friction.
• Log(time) strengthening - during holds.
• Instantaneous (direct) change in friction.
• Evolution with strain (e.g., Dc).
• Velocity-stepping and slide-hold-slide tests.
• Insight into the micromechanics of gouge that enable these phenomena.
Simple, one-variable dependence produces:
Initial Configuration
Lower Velocity; No Contact Healing
Largely distributed shear
Lower Velocity; w/ Contact Healing
Distributed shear w/ persistent slip planes
Higher Velocity; No Contact Healing
Largely distributed shear
Higher Velocity; w/ Contact Healing
Persistent localized shear strain
Velocity = 1E-3 m/s
Stick-Slip Deformation Mode: Cyclic Elastic Loading, Plastic Yield, and Failure.
Gradual Dilation -> Rapid Contraction.
Contact healing results in higher friction, higher
elastic modulus.
Velocity = 1E-1 m/s
Contact healing results in higher friction, greater
stress drop.
Oscillating Deformation Mode: ~Symmetric loading and unloading.
Undulating volume strain.
STEADY-STATE RESPONSE
Friction, dilation, and percentage of interparticle sliding increase with sliding velocity.
-> Velocity strengthening. Implies stable sliding.
HOLD – 100% Strain
Peak strength and stress drop show negative dependence on velocity.
Peak strength is enhanced. Volume strain is suppressed. Friction, sliding contacts, and volume trends are ~ uncorrelated by 108% strain.
HOLD – 138% Strain
Peak strength shows positive dependence on velocity.
Peak strength is enhanced. Volume strain is suppressed. Friction, sliding contacts, and volume trends are ~ uncorrelated by 143% strain.
Velocity Step-up:
1E-3->1E-2 µm/s1E-3->1E-1 µm/s
Direct increase in friction and % sliding contacts.
Gradual decay in direct effect, to higher steady state values.
-> Velocity Strengthening
Velocity Step-down:1E-1->1E-2 µm/s1E-1->1E-3 µm/s
Direct decrease in friction and % sliding contacts.
Gradual rise in direct effect, to lower steady- state values.
-> Velocity Strengthening
SUMMARY
• Using a simple log-time dependent contact healing law, we are able to reproduce many aspects of observed rate-state friction response.
• Most interesting is that our contacts are purely elastico-frictional – All “plasticity” is contained within granular interactions. What is “state” – geometry and particle packing?
Now for the – ANIMATIONS
(http://terra.rice.edu/department/faculty/~morganj)