Download - Butterfly Pendant
-
8/3/2019 Butterfly Pendant
1/22
B u t t e r f l y P e n d a n t
MATERIALS :
Bead with4mm hole
14-gauge dead soft wire, 34" long (copper,sterling, brass, or gold-filled)20-
gauge dead soft wire, 3" longWooden board at least 5" x 5" x
1/4"Finishing nailsPaperMarkerCordor chain with claspTape
T O O L S :
Planishingor ball peen hammerSteel blockWirecuttersRoundnose pliersFlat
nose pliersHammerFile
T E C H N I Q U E S :
Wirework, hammering, making a jig, beadsand wire.R R R R R R R R R R R R R R R R R R R
R R R R R R R R
-
8/3/2019 Butterfly Pendant
2/22
-
8/3/2019 Butterfly Pendant
3/22
-
8/3/2019 Butterfly Pendant
4/22
Step 1:
Lay the bead in the center of a sheet of paper,and trace around the bead.
Remove the bead.Draw a simple line design for the top of thebutterfly
wing. Start drawing at the top of thebead, and end near the center. Keepin mindthat you need a loop in the wire above thebead to pull a chain or
cord through. Try tomake it mimic the eyes of the butterfly. Start atthe
bottom of the bead, and draw a simplecurved line down and then up, to
end near thecenter of the bead. The two halves shouldtouch each other
at some point. Fill in with awidened line where you want the wire to
behammered flat.Trace this design, and flip over to repeat on
theopposite side. Make any adjustments necessary.Bewarethat too
much free floating wire couldaffect the wearability of the pendant.
To make the jig, place the finished drawing on a wooden board, and tape
or glue down. Hammer the finishing nails into the board at all
major turning points of the design. It is only necessary to do this for one
side of the butterfly. Clip the heads of the nails off with a heavy-duty
wire cutter.
Step 2:
Cut two 17" pieces of 14g wire. The length mayvary depending on the
final design. Check tomake sure they both fit in the bead together. If not,
file the bead hole opening larger until both wires fit through the
bead.Begin forging the wire by hammering a teardropshape on the end
of the wire. File the endsmooth.
Step 3:
Hold the teardrop in place with round nosepliers, and bend the wire into
a C shape withthe teardrop sitting flat in the C.
Step 4:
Place the C shape over the pattern, and bendthewire around the nails for
several turns.Butterfly Pendant
Copyright Interweave. Not to be reprinted. All rights reserved.
p a g e 2
publishers of
Step by Step Wire Jewelry
-
8/3/2019 Butterfly Pendant
5/22
-
8/3/2019 Butterfly Pendant
6/22
Step by Step Wire Jewelry
magazine . . . join the online beading community at
www.BeadingDaily.com
Lift the wire off the board, and hammerportions of the wire if necessary
to follow thedesign.
-
8/3/2019 Butterfly Pendant
7/22
Step 5:
Place the wire back on the jig, and bend thewire around the nails until
you reach the loopsabove the bead. Make a loop around the nail.
Step 6:
Hammer the remaining curves of the top of thewing.Step 7:
Repeat Steps 3-6 for the second piece of 14gwire. When forming loops
for the butterfly eyes,make sure you loop them in opposite directionsto
keep the design symmetrical. Straighten outthe remaining wire on each
piece. Use flat nosepliers if necessary to straighten out the wire.Line up
the two pieces next to each other, withthe wings flared out, and pull
both wiresthrough top of the bead.Place thebead andwireon
theboard, and startbending the wire around the nails fromthebottom up. Remove thewirefrom thenails.
Step 8:
Hammer the first curve of the lower portion of thewing.
Butterfly Pendant
Copyright Interweave. Not to be reprinted. All rights reserved.
p a g e 3 Step 4:Hammering the wire to shapeStep 6:Hammering the
wingsStep 5: Looping around the nailStep 7Step 8
-
8/3/2019 Butterfly Pendant
8/22
-
8/3/2019 Butterfly Pendant
9/22
Butterfly Wire Pendant
Download this Document for
FreePrintMobileCollectionsReport Document
-
8/3/2019 Butterfly Pendant
10/22
As promised, I will share with you the tutorial of making this wired bangle. I will split the tutorial into
3 parts. You may want to subscribe the blog post thru email so that you don't miss any post.
This is an interesting wired jewelry project. It shows you pictorial step by step to twist the wires and
come up with the wonderful wired bracelet.
I offer the tutorial in PDF that provide clearer intruction on the respective picture. If you are
interested to buy the eBook at USD3, contact me at diyjewelryclub at gmail dot com.
To make this bangle, you only need simple materials as follow:
Materials
3 pieces of 48cm / 19 inch thick copper wires sized 1mm/ 18 ga.
Thin copper wires sized 0.4mm/ 26 ga.
5 round beads measuring 1.5cm in diameter.
Tools Needed
Round nose pliers
Flat nose pliersWire Cutter
Step 1:Cut out 3 pieces of wires approximately 48cm/ 19 inch long.
Step 2
Bend each wire to oval shape at the middle of the wire.
The bracelet is about 2.2cm wide. For the outer wire, you will need to leave the spacing between the
top and bottom to be 2.2cm wide.
-
8/3/2019 Butterfly Pendant
11/22
Step 3
For the middle and inner wires, the spacing between the top and bottom wires is approximately
1.8cm and 1.5cm respectively.
Place the 3 wires side by side as shown in the picture.
We shall name the wires from 1 to 6 as shown in the picture. Throughout the tutorial, I will indicae
the number of the wires as per sequence in this picture for easy reference.
Step 4
Bend the inner wires upward at approximately 4cm (1.5inch) from the left side of the outer wires.
Cut approximately 6cm (2.5inch) of thin wires (26ga). At the area where the inner wires is bend, wrap
the thick wires with the thin wire.
-
8/3/2019 Butterfly Pendant
12/22
Part 2 to be continued in next post!
This is part 2 of the Free Form Wired Bangle Tutorial:
Step 5:
Wrap the wires around 4 times. Cut off excess wires. You have completed the 1st joint for the bangle.
Step 6:
-
8/3/2019 Butterfly Pendant
13/22
Thread in a 1.5cm of round bead into the wire numbered 3.
Step 7:
Pull it nearer to the 1st joint.
Step 8:
Now shape the wires numbered 2 and 4 around the bead. Wires 2, 3 and 4 will join at the other end
of the bead. Get ready with a 6cm of thin wires.
-
8/3/2019 Butterfly Pendant
14/22
Step 9
Cut off excess wires once the 2nd joint is completed. Wrap the thin wires around the joint 4 times.
Step 10
Now thread in another 1.5cm round bead through wire numbered 5.
-
8/3/2019 Butterfly Pendant
15/22
Step 11
Shape the wires around the bead. Wires numbered 3, 4, 5 & 6 will be joining at the end of the bead.
Get a 6cm thin wires to wrap around the wires 4 times. You have completed wrapping the 3rd joint.
Step 12
Now thread in the 3rd 1.5cm round bead through the wire numbered 3.
-
8/3/2019 Butterfly Pendant
16/22
I offer the tutorial in PDF that provide clearer intruction on the respective picture. If you are
interested to buy the eBook at USD3, contact me at diyjewelryclub at gmail dot com.
Part 3 to be continued in my next post.
Don't miss a post! Subscribe to Handmade Jewelry Club by Email FREE
Feel free to distribute the content of the post. However, you must give credit by providing a link back
to http://www.handmade-jewelry-club.com/Step 13
Join wires numbered 1, 2, 3 and 4 at the end of the bead and wrap them with a thin wires 4 times.
Step 14
Thread in the 4th 1.5cm round bead into the wire numbered 2.
-
8/3/2019 Butterfly Pendant
17/22
Step 15
Join the wires numbered 1, 2, 3 & 4 at the end of the 4th bead with a thin wire.
Step 16
Wrap around 4 times at the 5th joint.
Step 17
Thread in the 5th bead into the wires numbered 3.
-
8/3/2019 Butterfly Pendant
18/22
Step 18
Join wires numbered 3,4,5 at the end of the bead by using a thin wire
Step 19
Wrap around the wires 4 times to form the 6th joint.
-
8/3/2019 Butterfly Pendant
19/22
Step 20
Make a loop at the end of each wire. To do so, hold the end of the wires using round nose pliers and
turn it inward towards your body using your wrist.
-
8/3/2019 Butterfly Pendant
20/22
Step 21
Wrap around wires numbered 1, 2, 3 and 4 using a thin wire.
You have completed with the bangle. If you like, you can decorate the bangle with some spirals. Just
follow the steps below:
Cut approximately 13cm or 5 inch of thin wires. Find a place at the bangle where you would like to
add more spirals. Wrap around this location using the thin wires.
-
8/3/2019 Butterfly Pendant
21/22
Step 22
At both ends of the wires, make spirals.
-
8/3/2019 Butterfly Pendant
22/22
I offer the tutorial in PDF format that provides clearer reference on the respective pictures. If you are
interested to buy the eBook at USD3, contact me at diyjewelryclub at gmail dot com.
Don't miss a post! Subscribe to Handmade Jewelry Club by Email FREE
Feel free to distribute the content of the post. Just give us a credit by providing a link back to
http://www.handmade-jewelry-club.com/