ASKAYNAK by HARRISGas Equipment
Head Mixing Cutting Equipment
Welding&Brazing Equipment
Oxy-Propane/Natural Heating Equipment
Cutting Capacity up to 150 mm
STRONGER
SAFERHead Mixing Technology &
High Work Safety
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.2 3
Designed and manufactured according to ISO 5172.Harris offers torches specifically designed for the best performance possible with each fuel gas:
Equal pressure system with acetylene and alternative fuel:• Head mixing• Equal pressure mixing of oxygen and fuel gas is extremely resistant to backfire • Torch can be used with all fuel gases - just change the tips
Typical “E” Mixer DesignTo thoroughly mix the oxygen and fuel gas, “E” mixer designs rely on equal pressure control of both oxygen and fuel gas Both gases enter the mixing chamber at controlled pressures. “E” mixers allow the end-user greater control of the oxy/fuel ratio. This feature has an advantage in applications where a very carburizing or oxidizing flame is required. Also, because of their higher potential flow rates, “E” mixers are required for high flow heating applications. This design is primarily used with acetylene but can also be used with alternative fuels when positive pressure control of the fuel gas is available.
FUEL GAS
OXYGENOXY / FUEL MIX
FUEL GAS
TYPICAL “E” MIXER DESIGN
Head Mixing Technology
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.2 3
Askaynak by Harris
Head Mixing Cutting Equipment Head Mixing Teachnology ............................................................................................................................ 218Oxy-Acetylene Gas Cutting Equipment ..................................................................................................... 220Oxy-Propane / Natural Gas Cutting Equipment ..................................................................................... 222
Welding&Brazing Equipment Oxy-Acetylene Welding & Brazing Equipment .........................................................................................224Oxy-Propane/Natural Brazing Equipment ................................................................................................ 226Oxy-Gas Welding & Brazing Sets .............................................................................................................. 228
Heating Equipment Oxy-Propane/Natural Gaz Heating Equipment ....................................................................................... 230
Welding HosesHARRIS Welding Hoses ............................................................................................................................... 232
AccessoryGoggles, Wrench, Tip Cleaner for Machine Cutting and Hand CuttingLighter With Flint, Circular Cutting Attachment ..................................................................................... 233
Index
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.2 3
Designed and manufactured according to ISO 5172.Harris offers torches specifically designed for the best performance possible with each fuel gas:
Equal pressure system with acetylene and alternative fuel:• Head mixing• Equal pressure mixing of oxygen and fuel gas is extremely resistant to backfire • Torch can be used with all fuel gases - just change the tips
Typical “E” Mixer DesignTo thoroughly mix the oxygen and fuel gas, “E” mixer designs rely on equal pressure control of both oxygen and fuel gas Both gases enter the mixing chamber at controlled pressures. “E” mixers allow the end-user greater control of the oxy/fuel ratio. This feature has an advantage in applications where a very carburizing or oxidizing flame is required. Also, because of their higher potential flow rates, “E” mixers are required for high flow heating applications. This design is primarily used with acetylene but can also be used with alternative fuels when positive pressure control of the fuel gas is available.
FUEL GAS
OXYGENOXY / FUEL MIX
FUEL GAS
TYPICAL “E” MIXER DESIGN
Head Mixing Technology
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.2 3
Askaynak by Harris
Head Mixing Cutting Equipment Head Mixing Teachnology ............................................................................................................................ 218Oxy-Acetylene Gas Cutting Equipment ..................................................................................................... 220Oxy-Propane / Natural Gas Cutting Equipment ..................................................................................... 222
Welding&Brazing Equipment Oxy-Acetylene Welding & Brazing Equipment .........................................................................................224Oxy-Propane/Natural Brazing Equipment ................................................................................................ 226Oxy-Gas Welding & Brazing Sets .............................................................................................................. 228
Heating Equipment Oxy-Propane/Natural Gaz Heating Equipment ....................................................................................... 230
Welding HosesHARRIS Welding Hoses ............................................................................................................................... 232
AccessoryGoggles, Wrench, Tip Cleaner for Machine Cutting and Hand CuttingLighter With Flint, Circular Cutting Attachment ..................................................................................... 233
Index
219Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.4 5
82HC552D
Product Number Angle (Right-Left) Max. Cutting Diameter
82HC552D 30˚ 600 mm
MODEL-552D CIRCULAR CUTTING ATTACHMENT
Product Number Plate Thickness (mm) Oxygen (bar) Acetylene (bar)
82HC5521A 3-25 2,5-4 0,3
82HC5522A 25-75 4-5 0,3
82HC5523A 75-150 5-6 0,3
82HC552AT 3-150
MODEL-552A OXY-ACETYLENE CUTTING TIPS
Acetylene Cutting Tips Set (3 sizes)
Product Number Plate Thickness Fuel Gases
82HC552 3-150 mm Acetylen - Propane - Natural Gas
MODEL-552 CUTTING ATTACHMENT
82HC5521A3-25 mm
82HC552
82HC5522A25-75 mm
82HC5523A75-150 mm
CUTTINGCAPACITYCUTTINGCAPACITY
150mm
150mm
Oxy-Acetylene Gas Cutting Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.4 5
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
Product Number
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552AT 3-150 mm Acetylene Cutting Tips Set (3 sizes)
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552AT 3-150 mm Acetylene Cutting Tips Set (3 sizes)
82HC552D Circular cutting attachment
MODEL-553A OXY-ACETYLENE CUTTING SETS
82HC553A
82HC553AD
Set Content
82HC551
G 1/4”
G 3/8” Left
82HC553A
82HC553AD
+
220Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.4 5
82HC552D
Product Number Angle (Right-Left) Max. Cutting Diameter
82HC552D 30˚ 600 mm
MODEL-552D CIRCULAR CUTTING ATTACHMENT
Product Number Plate Thickness (mm) Oxygen (bar) Acetylene (bar)
82HC5521A 3-25 2,5-4 0,3
82HC5522A 25-75 4-5 0,3
82HC5523A 75-150 5-6 0,3
82HC552AT 3-150
MODEL-552A OXY-ACETYLENE CUTTING TIPS
Acetylene Cutting Tips Set (3 sizes)
Product Number Plate Thickness Fuel Gases
82HC552 3-150 mm Acetylen - Propane - Natural Gas
MODEL-552 CUTTING ATTACHMENT
82HC5521A3-25 mm
82HC552
82HC5522A25-75 mm
82HC5523A75-150 mm
CUTTINGCAPACITYCUTTINGCAPACITY
150mm
150mm
Oxy-Acetylene Gas Cutting Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.4 5
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
Product Number
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552AT 3-150 mm Acetylene Cutting Tips Set (3 sizes)
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552AT 3-150 mm Acetylene Cutting Tips Set (3 sizes)
82HC552D Circular cutting attachment
MODEL-553A OXY-ACETYLENE CUTTING SETS
82HC553A
82HC553AD
Set Content
82HC551
G 1/4”
G 3/8” Left
82HC553A
82HC553AD
+
221Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.6 7
82HC552D
82HC5524
Product Number Plate Thickness Fuel Gases
82HC552 3-150 mm Acetylene - Propane - Natural Gas
MODEL-552 CUTTING ATTACHMENT
82HC552
3-150 mm
Product Number Plate Thickness (mm) Oxygen (bar) Fuel Gases (bar)
82HC5521P 3-25 2,5-4 0,3
82HC5522P 25-75 4-5 0,3
82HC5523P 75-150 5-6 0,3
82HC5524 3-150
82HC552PT 3-150
Cooper Shell
Propane / Natural Gas Cutting Tips (3 sizes+Cooper Shell)
MODEL-552P OXY-PROPANE / NATURAL GAS CUTTING TIPS
82HC5521P 82HC5522P 82HC5523P3-25 mm 25-75 mm 75-150 mm
Product Number Angle (Right-Left) Max. Cutting Diameter
82HC552D 30˚ 600 mm
MODEL-552D CIRCULAR CUTTING ATTACHMENT
CUTTINGCAPACITYCUTTINGCAPACITY
150mm
150mm
Oxy-Propane / Natural Gas Cutting Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.6 7
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
82HC551
G 1/4”
G 3/8” Left
Product Number
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552PT 3-150 mm Propane / Natural Gas Cutting Tips (3 Sizes)
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552PT 3-150 mm Propane / Natural Gas Cutting Tips (3 Sizes)
82HC552D 3-150 mm Propane / Natural Gas Cutting Tips (3 Sizes)
MODEL-553P OXY-PROPANE / NATURAL GAS CUTTING SETS
82HC553P
82HC553PD
Set Contents
82HC553P
82HC553PD
+
222Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.6 7
82HC552D
82HC5524
Product Number Plate Thickness Fuel Gases
82HC552 3-150 mm Acetylene - Propane - Natural Gas
MODEL-552 CUTTING ATTACHMENT
82HC552
3-150 mm
Product Number Plate Thickness (mm) Oxygen (bar) Fuel Gases (bar)
82HC5521P 3-25 2,5-4 0,3
82HC5522P 25-75 4-5 0,3
82HC5523P 75-150 5-6 0,3
82HC5524 3-150
82HC552PT 3-150
Cooper Shell
Propane / Natural Gas Cutting Tips (3 sizes+Cooper Shell)
MODEL-552P OXY-PROPANE / NATURAL GAS CUTTING TIPS
82HC5521P 82HC5522P 82HC5523P3-25 mm 25-75 mm 75-150 mm
Product Number Angle (Right-Left) Max. Cutting Diameter
82HC552D 30˚ 600 mm
MODEL-552D CIRCULAR CUTTING ATTACHMENT
CUTTINGCAPACITYCUTTINGCAPACITY
150mm
150mm
Oxy-Propane / Natural Gas Cutting Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.6 7
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
82HC551
G 1/4”
G 3/8” Left
Product Number
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552PT 3-150 mm Propane / Natural Gas Cutting Tips (3 Sizes)
82HC551 Model-551 Handle
82HC552 Model-552 Cutting Attachment
82HC552PT 3-150 mm Propane / Natural Gas Cutting Tips (3 Sizes)
82HC552D 3-150 mm Propane / Natural Gas Cutting Tips (3 Sizes)
MODEL-553P OXY-PROPANE / NATURAL GAS CUTTING SETS
82HC553P
82HC553PD
Set Contents
82HC553P
82HC553PD
+
223Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.8 9
Product Number Plate Thickness
82HC554M1 0,2 - 20 mm (M1 Type Mixer)
82HC554M2 20 - 50 mm (M2 Type Mixer)
MODEL-554M WELDING MIXER
Product Number Plate Thickness(mm)
Oxygen(bar)
Acetylene(bar)
82HC554A0 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8
82HC554A1 0,5 - 1 0,3 - 0,8 0,3 - 0,8
82HC554A3 1 - 2 0,3 - 0,8 0,3 - 0,8
82HC554A5 2 - 4 0,3 - 0,8 0,3 - 0,8
82HC554A6 4 - 6 0,3 - 0,8 0,3 - 0,8
82HC554A8 6 - 9 0,3 - 0,8 0,3 - 0,8
82HC554A9 9 - 14 0,3 - 0,8 0,3 - 0,8
82HC554A10 14 - 20 0,3 - 0,8 0,3 - 0,8
82HC554A13 20 - 30 0,3 - 0,8 0,3 - 0,8
82HC554A15 30 - 50 0,3 - 0,8 0,3 - 0,8
MODEL-554 OXY-ACETYLENE WELDING & BRAZING TIPS
82HC554M2
82HC554M1
82HC554A1
82HC554A5
82HC554A8
82HC554A10
82HC554A3
82HC554A6
82HC554A9
82HC554A13
82HC554A15
82HC554A00,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
Oxy-Acetylene Welding & Brazing Tips Design Detail
Oxy-Acetylene Welding & Brazing Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.8 9
82HC551
Product Number ConnectionDiameter
Oxygen Thread
ThreadFuel Gas
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
Product Number Plate Thickness(mm)
Oxygen (bar)
Acetylen(bar) Products
82HC5541 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A0 Tip
82HC5542 0,5 - 1 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A1 Tip
82HC5543 1 - 2 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A3 Tip
82HC5544 2 - 4 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A5 Tip
82HC5545 4 - 6 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A6 Tip
82HC5546 6 - 9 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A8 Tip
82HC5547 9 - 14 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer+ 82HC554A9 Tip
82HC5548 14 - 20 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A10 Tip
82HC5549 20 - 30 0,3 - 0,8 0,3 - 0,8 82HC554M2 Mixer + 82HC554A13 Tip
82HC55410 30 - 50 0,3 - 0,8 0,3 - 0,8 82HC554M2 Mikser + 82HC554A15 Tip
MODEL-554 OXY-ACETYLENE BRAZING ASSEMBLIES
G 1/4”
G 3/8” Left
82HC5542
82HC5544
82HC5546
82HC5548
82HC5543
82HC5545
82HC5547
82HC5549
82HC55410
82HC55410,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
224Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.8 9
Product Number Plate Thickness
82HC554M1 0,2 - 20 mm (M1 Type Mixer)
82HC554M2 20 - 50 mm (M2 Type Mixer)
MODEL-554M WELDING MIXER
Product Number Plate Thickness(mm)
Oxygen(bar)
Acetylene(bar)
82HC554A0 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8
82HC554A1 0,5 - 1 0,3 - 0,8 0,3 - 0,8
82HC554A3 1 - 2 0,3 - 0,8 0,3 - 0,8
82HC554A5 2 - 4 0,3 - 0,8 0,3 - 0,8
82HC554A6 4 - 6 0,3 - 0,8 0,3 - 0,8
82HC554A8 6 - 9 0,3 - 0,8 0,3 - 0,8
82HC554A9 9 - 14 0,3 - 0,8 0,3 - 0,8
82HC554A10 14 - 20 0,3 - 0,8 0,3 - 0,8
82HC554A13 20 - 30 0,3 - 0,8 0,3 - 0,8
82HC554A15 30 - 50 0,3 - 0,8 0,3 - 0,8
MODEL-554 OXY-ACETYLENE WELDING & BRAZING TIPS
82HC554M2
82HC554M1
82HC554A1
82HC554A5
82HC554A8
82HC554A10
82HC554A3
82HC554A6
82HC554A9
82HC554A13
82HC554A15
82HC554A00,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
Oxy-Acetylene Welding & Brazing Tips Design Detail
Oxy-Acetylene Welding & Brazing Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.8 9
82HC551
Product Number ConnectionDiameter
Oxygen Thread
ThreadFuel Gas
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
Product Number Plate Thickness(mm)
Oxygen (bar)
Acetylen(bar) Products
82HC5541 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A0 Tip
82HC5542 0,5 - 1 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A1 Tip
82HC5543 1 - 2 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A3 Tip
82HC5544 2 - 4 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A5 Tip
82HC5545 4 - 6 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A6 Tip
82HC5546 6 - 9 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A8 Tip
82HC5547 9 - 14 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer+ 82HC554A9 Tip
82HC5548 14 - 20 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC554A10 Tip
82HC5549 20 - 30 0,3 - 0,8 0,3 - 0,8 82HC554M2 Mixer + 82HC554A13 Tip
82HC55410 30 - 50 0,3 - 0,8 0,3 - 0,8 82HC554M2 Mikser + 82HC554A15 Tip
MODEL-554 OXY-ACETYLENE BRAZING ASSEMBLIES
G 1/4”
G 3/8” Left
82HC5542
82HC5544
82HC5546
82HC5548
82HC5543
82HC5545
82HC5547
82HC5549
82HC55410
82HC55410,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
225Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.10 11
Product Number Plate Thickness
82HC554M1 0,2 - 20 mm (M1 Type Mixer)
82HC554M2 20 - 50 mm (M2 Type Mixer)
MODEL-554M WELDING MIXER
Product Number Plate Thickness(mm)
Oxygen(bar)
Propane / Natural Gas(bar)
82HC555P0 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8
82HC555P1 0,5 - 1 0,3 - 0,8 0,3 - 0,8
82HC555P3 1 - 2 0,3 - 0,8 0,3 - 0,8
82HC555P5 2 - 4 0,3 - 0,8 0,3 - 0,8
82HC555P6 4 - 6 0,3 - 0,8 0,3 - 0,8
82HC555P8 6 - 9 0,3 - 0,8 0,3 - 0,8
82HC555P9 9 - 14 0,3 - 0,8 0,3 - 0,8
82HC555P10 14 - 20 0,3 - 0,8 0,3 - 0,8
82HC555P13 20 - 30 0,3 - 1 0,3 - 1
82HC555P15 30 - 50 0,3 - 1 0,3 - 1
MODEL-555 PROPANE / NATURAL GAS BRAZING TIPS
Askaynak by Harris product range offers its users the ability of performing brazing with Propane gas. Especially in oxy-gas equipment market it is seen that acetylene gas with proper soldering torches and nozzles are used for brazing with propane gas. Model-555 brazing torches included in Askaynak by Harris product range are specially designed for enabling brazing with propane gas.
82HC554M2
82HC554M1
82HC555P1
82HC555P5
82HC555P8
82HC555P10
82HC555P3
82HC555P6
82HC555P9
82HC555P13
82HC555P15
82HC555P00,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
Oxy-Propane / Natural Gas (LPG) Brazing Tips Design
Detail
Oxy-Propane / Natural Gas Brazing Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.10 11
82HC551
Product Number Plate Thickness(mm)
Oxygen(bar)
Propane / Natural Gas(bar) Products
82HC5551 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P0 Tip
82HC5552 0,5 - 1 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P1 Tip
82HC5553 1 - 2 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P3 Tip
82HC5554 2 - 4 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P5 Tip
82HC5555 4 - 6 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P6 Tip
82HC5556 6 - 9 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P8 Tip
82HC5557 9 - 14 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer+ 82HC555P9 Tip
82HC5558 14 - 20 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P10 Tip
82HC5559 20 - 30 0,3 - 1 0,3 - 1 82HC554M2 Mixer + 82HC555P13 Tip
82HC55510 30 - 50 0,3 - 1 0,3 - 1 82HC554M2 Mixer + 82HC555P15 Tip
MODEL-555 PROPANE / NATURAL GAS BRAZING ASSEMBLIES ( Mixer + Tip )
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
G 1/4”
G 3/8” Left
82HC5552
82HC5554
82HC5556
82HC5558
82HC5553
82HC5555
82HC5557
82HC5559
82HC55510
82HC55510,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
226Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.10 11
Product Number Plate Thickness
82HC554M1 0,2 - 20 mm (M1 Type Mixer)
82HC554M2 20 - 50 mm (M2 Type Mixer)
MODEL-554M WELDING MIXER
Product Number Plate Thickness(mm)
Oxygen(bar)
Propane / Natural Gas(bar)
82HC555P0 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8
82HC555P1 0,5 - 1 0,3 - 0,8 0,3 - 0,8
82HC555P3 1 - 2 0,3 - 0,8 0,3 - 0,8
82HC555P5 2 - 4 0,3 - 0,8 0,3 - 0,8
82HC555P6 4 - 6 0,3 - 0,8 0,3 - 0,8
82HC555P8 6 - 9 0,3 - 0,8 0,3 - 0,8
82HC555P9 9 - 14 0,3 - 0,8 0,3 - 0,8
82HC555P10 14 - 20 0,3 - 0,8 0,3 - 0,8
82HC555P13 20 - 30 0,3 - 1 0,3 - 1
82HC555P15 30 - 50 0,3 - 1 0,3 - 1
MODEL-555 PROPANE / NATURAL GAS BRAZING TIPS
Askaynak by Harris product range offers its users the ability of performing brazing with Propane gas. Especially in oxy-gas equipment market it is seen that acetylene gas with proper soldering torches and nozzles are used for brazing with propane gas. Model-555 brazing torches included in Askaynak by Harris product range are specially designed for enabling brazing with propane gas.
82HC554M2
82HC554M1
82HC555P1
82HC555P5
82HC555P8
82HC555P10
82HC555P3
82HC555P6
82HC555P9
82HC555P13
82HC555P15
82HC555P00,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
Oxy-Propane / Natural Gas (LPG) Brazing Tips Design
Detail
Oxy-Propane / Natural Gas Brazing Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.10 11
82HC551
Product Number Plate Thickness(mm)
Oxygen(bar)
Propane / Natural Gas(bar) Products
82HC5551 0,2 - 0,5 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P0 Tip
82HC5552 0,5 - 1 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P1 Tip
82HC5553 1 - 2 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P3 Tip
82HC5554 2 - 4 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P5 Tip
82HC5555 4 - 6 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P6 Tip
82HC5556 6 - 9 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P8 Tip
82HC5557 9 - 14 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer+ 82HC555P9 Tip
82HC5558 14 - 20 0,3 - 0,8 0,3 - 0,8 82HC554M1 Mixer + 82HC555P10 Tip
82HC5559 20 - 30 0,3 - 1 0,3 - 1 82HC554M2 Mixer + 82HC555P13 Tip
82HC55510 30 - 50 0,3 - 1 0,3 - 1 82HC554M2 Mixer + 82HC555P15 Tip
MODEL-555 PROPANE / NATURAL GAS BRAZING ASSEMBLIES ( Mixer + Tip )
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
G 1/4”
G 3/8” Left
82HC5552
82HC5554
82HC5556
82HC5558
82HC5553
82HC5555
82HC5557
82HC5559
82HC55510
82HC55510,2 - 0,5 mm
1 - 2 mm
4 - 6 mm
9 - 14 mm
20 - 30 mm
0,5 - 1 mm
2 - 4 mm
6 - 9 mm
14 - 20 mm
30 - 50 mm
227Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.12 13
Product Number
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC554A1 0,5 - 1 mm Welding & Brazing Tips
82HC55411 82HC554A3 1 - 2 mm Welding & Brazing Tips
82HC554A5 2 - 4 mm Welding & Brazing Tips
82HC554A6 4 - 6 mm Welding & Brazing Tips
82HC554A8 6 - 9 mm Welding & Brazing Tips
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC55412 82HC554A1 0,5 - 1 mm Welding & Brazing Tips
82HC554A3 1 - 2 mm Welding & Brazing Tips
82HC554A5 2 - 4 mm Welding & Brazing Tips
MODEL-554 OXY-ACETYLENE WELDING & BRAZING SETSSet Contents
82HC55411 82HC55412
Oxy-Acetylene Welding & Brazing Sets
Oxy-Gas Welding & Brazing Sets
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.12 13
Product Number
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC555P1 0,5 - 1 mm Brazing Tips
82HC55511 82HC555P3 1 - 2 mm Brazing Tips
82HC555P5 2 - 4 mm Brazing Tips
82HC555P6 4 - 6 mm Brazing Tips
82HC555P8 6 - 9 mm Brazing Tips
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC55512 82HC555P1 0,5 - 1 mm Brazing Tips
82HC555P3 1 - 2 mm Brazing Tips
82HC555P5 2 - 4 mm Brazing Tips
MODEL-555 OXY-PROPANE / NATURAL GAS BRAZING SETSSet Contents
82HC55511 82HC55512
Oxy-Propane / Natural Gas Brazing Sets
Oxy-Gas Welding & Brazing Sets
228Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.12 13
Product Number
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC554A1 0,5 - 1 mm Welding & Brazing Tips
82HC55411 82HC554A3 1 - 2 mm Welding & Brazing Tips
82HC554A5 2 - 4 mm Welding & Brazing Tips
82HC554A6 4 - 6 mm Welding & Brazing Tips
82HC554A8 6 - 9 mm Welding & Brazing Tips
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC55412 82HC554A1 0,5 - 1 mm Welding & Brazing Tips
82HC554A3 1 - 2 mm Welding & Brazing Tips
82HC554A5 2 - 4 mm Welding & Brazing Tips
MODEL-554 OXY-ACETYLENE WELDING & BRAZING SETSSet Contents
82HC55411 82HC55412
Oxy-Acetylene Welding & Brazing Sets
Oxy-Gas Welding & Brazing Sets
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.12 13
Product Number
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC555P1 0,5 - 1 mm Brazing Tips
82HC55511 82HC555P3 1 - 2 mm Brazing Tips
82HC555P5 2 - 4 mm Brazing Tips
82HC555P6 4 - 6 mm Brazing Tips
82HC555P8 6 - 9 mm Brazing Tips
82HC551 Model-551 Handle
82MC554M1 Mixer (M1)
82HC55512 82HC555P1 0,5 - 1 mm Brazing Tips
82HC555P3 1 - 2 mm Brazing Tips
82HC555P5 2 - 4 mm Brazing Tips
MODEL-555 OXY-PROPANE / NATURAL GAS BRAZING SETSSet Contents
82HC55511 82HC55512
Oxy-Propane / Natural Gas Brazing Sets
Oxy-Gas Welding & Brazing Sets
229Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.14 15
Product Number Product Description
82HC556M Heating Mixer (M)
82HC2357-3 Heating Adapter
HEATING MIXER and ADAPTER
82HC2357-3
82HC556M
82HC5562
82HC5564
82HC5563
82HC5565
82HC5561
420 mm
600 mm
420 mm
490 mm
670 mm
82HC556T3 82HC556T582HC556T282HC556T1 82HC556T4
T1 T2 T3 T4 T5
Oxy-Propane/Natural Gas Heating Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.14 15
Product Number Description Oxygen (bar)
Propane / Natural Gas(bar)
82HC556T1 T1 Tip 1 - 2 0,5
82HC556T2 T2 Tip 2 - 3 0,5
82HC556T3 T3 Tip 2 - 5 1
82HC556T4 T4 Tip 3 - 6 1
82HC556T5 T5 Tip 4 - 8 1 - 2
MODEL-556T OXY-PROPANE / NATURAL GAS HEATING TIPS
Product Number Length(mm)
Oxygen(bar) Propane / Natural Gas (bar)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55642 Heating Tube
82HC556T1 Heating Tip (T1)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55642 Heating Tube
82HC556T2 Heating Tip (T2)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55649 Heating Tube
82HC556T3 Heating Tip (T3)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55660 Heating Tube
82HC556T4 Heating Tip (T4)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55667 Heating Tube
82HC556T5 Heating Tip (T5)
MODEL-556 OXY-PROPANE / NATURAL GAS HEATING ASSAMBLIES
82HC5561 420 1 - 2 0,5
82HC5563 490 2 - 5 1
82HC5562 420 2 - 3 0,5
82HC5564 600 3 - 6 1
82HC5565 670 4 - 8 1 - 2
Products
82HC551
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
G 1/4”
G 3/8” Left
230Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.14 15
Product Number Product Description
82HC556M Heating Mixer (M)
82HC2357-3 Heating Adapter
HEATING MIXER and ADAPTER
82HC2357-3
82HC556M
82HC5562
82HC5564
82HC5563
82HC5565
82HC5561
420 mm
600 mm
420 mm
490 mm
670 mm
82HC556T3 82HC556T582HC556T282HC556T1 82HC556T4
T1 T2 T3 T4 T5
Oxy-Propane/Natural Gas Heating Equipment
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.14 15
Product Number Description Oxygen (bar)
Propane / Natural Gas(bar)
82HC556T1 T1 Tip 1 - 2 0,5
82HC556T2 T2 Tip 2 - 3 0,5
82HC556T3 T3 Tip 2 - 5 1
82HC556T4 T4 Tip 3 - 6 1
82HC556T5 T5 Tip 4 - 8 1 - 2
MODEL-556T OXY-PROPANE / NATURAL GAS HEATING TIPS
Product Number Length(mm)
Oxygen(bar) Propane / Natural Gas (bar)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55642 Heating Tube
82HC556T1 Heating Tip (T1)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55642 Heating Tube
82HC556T2 Heating Tip (T2)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55649 Heating Tube
82HC556T3 Heating Tip (T3)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55660 Heating Tube
82HC556T4 Heating Tip (T4)
82HC556M Heating Mixer
82HC2357-3 Heating Adapter
82HC55667 Heating Tube
82HC556T5 Heating Tip (T5)
MODEL-556 OXY-PROPANE / NATURAL GAS HEATING ASSAMBLIES
82HC5561 420 1 - 2 0,5
82HC5563 490 2 - 5 1
82HC5562 420 2 - 3 0,5
82HC5564 600 3 - 6 1
82HC5565 670 4 - 8 1 - 2
Products
82HC551
Product Number ConnectionDiameter
OxygenThread
Fuel GasThread
82HC551 Ø 16 mm G 1/4" G 3/8" Left
MODEL-551 HANDLE
G 1/4”
G 3/8” Left
231Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.16 17
Oxy-Welding Hose
HARRIS Twin Oxy-Welding Hose
In applications performed with oxy-gas equipment, although usage of twin oxy-welding hoses is necessary, unfortunately mostly it is seen that operators prefer air hoses.
While the material of air hoses is polyvinyl chloride, twin oxy-welding hoses are manufactured from rubber. Tiny hot work pieces/sparks falling on to the air hoses nestle into the hose by rapidly melting down the PVC. In this situation, tiny hot work pieces/sparks that reach the gas within the hose may cause fire or explosion. In synthetic rubber welding hoses, tiny hot work pieces/sparks falling on to the hose drop down by slipping over the hose where they contact. Thus, in case of any danger, twin oxy-welding hoses minimize explosion risk as well as save time for the operator to take necessary precautions against danger. Therefore, usage of twin oxy-welding hose in oxy-gas systems is highly important in terms of occupational safety.
Welding hoses consist of two adherent hoses. One of these hoses is in blue color that indicates oxygen gas. Other’s color varies depending on the type of fuel gas. In Harris twin oxy- welding hoses the color of fuel gas hose is orange for propane/LPG and natural gas and red for acetylene gas. Thanks to this color difference, you can easily determine the gas which the operator works with.
Turkish Standards Institution has been certifying twin oxy-welding hoses according to EN ISO 3821 as of 07.18.2013. Harris twin oxy-gas welding hoses are also manufactured according to EN ISO 3821. Twin oxy-gas welding hoses used in oxy-gas systems of all manufacturing facilities that are audited within the framework of 6331 numbered occupational safety law are required to be in conformity with EN ISO 3821.
82HCTA8X882HCTA8X6 82HCTA8X8LP
Product Number Hose Diameter
82HCTA8X8 8 mm
82HCTA6X6 6 mm
OXY-ACETYLENE TWIN HOSEProduct Number Hose Diameter
82HCTA8X8LP 8 mm
OXY-PROPANE / NATURAL GAS TWIN HOSE
Burned into flameHARRIS Twin Oxy-welding hose
Burned into flame Air Hose HARRIS Oxy-Propane/Natural Gas Twin Hose
HARRIS Oxy-Acetylene Twin Hose
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.16 17
Accessory
82HC552D
82HC26SL
82HCE9
82HCAPS010
82HCC9
82HCI62X
82HC26L Inclined cutting for welding groove ( 30° Right-Left ) Circular cutting (Diameter 600 mm)4 mm plate thickness, high strengthChrome plateBrass wheel seats and special design for continous rolling
Product Number Description
82HCE9 For Machine Cutting Tips
Product Number Description
82HCC9 For Cutting and Welding&Brazing Tips
Product Number Angle (Right-Left) Max. Cutting Diameter
82H552D 30˚ 600 mm
TIP CLEANER FOR MACHINE CUTTING TIP TIP CLEANIN HAND CUTTING TIP
CIRCULAR CUTTING ATTACHMENTProduct Number Description
82HC26SL Lighter for oxy-gas systems
82HC26L Flints (5 pcs)
LIGHTER WITH FLINT
Product Number Description
82HCI62X Wrench for nuts
WRENCH
Product Number Description
82HCAPS010 Goggles for oxy-gas systems
GOGGLES
HARRIS Welding Accessory
Oxy-Welding Hose
232Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.16 17
Oxy-Welding Hose
HARRIS Twin Oxy-Welding Hose
In applications performed with oxy-gas equipment, although usage of twin oxy-welding hoses is necessary, unfortunately mostly it is seen that operators prefer air hoses.
While the material of air hoses is polyvinyl chloride, twin oxy-welding hoses are manufactured from rubber. Tiny hot work pieces/sparks falling on to the air hoses nestle into the hose by rapidly melting down the PVC. In this situation, tiny hot work pieces/sparks that reach the gas within the hose may cause fire or explosion. In synthetic rubber welding hoses, tiny hot work pieces/sparks falling on to the hose drop down by slipping over the hose where they contact. Thus, in case of any danger, twin oxy-welding hoses minimize explosion risk as well as save time for the operator to take necessary precautions against danger. Therefore, usage of twin oxy-welding hose in oxy-gas systems is highly important in terms of occupational safety.
Welding hoses consist of two adherent hoses. One of these hoses is in blue color that indicates oxygen gas. Other’s color varies depending on the type of fuel gas. In Harris twin oxy- welding hoses the color of fuel gas hose is orange for propane/LPG and natural gas and red for acetylene gas. Thanks to this color difference, you can easily determine the gas which the operator works with.
Turkish Standards Institution has been certifying twin oxy-welding hoses according to EN ISO 3821 as of 07.18.2013. Harris twin oxy-gas welding hoses are also manufactured according to EN ISO 3821. Twin oxy-gas welding hoses used in oxy-gas systems of all manufacturing facilities that are audited within the framework of 6331 numbered occupational safety law are required to be in conformity with EN ISO 3821.
82HCTA8X882HCTA8X6 82HCTA8X8LP
Product Number Hose Diameter
82HCTA8X8 8 mm
82HCTA6X6 6 mm
OXY-ACETYLENE TWIN HOSEProduct Number Hose Diameter
82HCTA8X8LP 8 mm
OXY-PROPANE / NATURAL GAS TWIN HOSE
Burned into flameHARRIS Twin Oxy-welding hose
Burned into flame Air Hose HARRIS Oxy-Propane/Natural Gas Twin Hose
HARRIS Oxy-Acetylene Twin Hose
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.16 17
Accessory
82HC552D
82HC26SL
82HCE9
82HCAPS010
82HCC9
82HCI62X
82HC26L Inclined cutting for welding groove ( 30° Right-Left ) Circular cutting (Diameter 600 mm)4 mm plate thickness, high strengthChrome plateBrass wheel seats and special design for continous rolling
Product Number Description
82HCE9 For Machine Cutting Tips
Product Number Description
82HCC9 For Cutting and Welding&Brazing Tips
Product Number Angle (Right-Left) Max. Cutting Diameter
82H552D 30˚ 600 mm
TIP CLEANER FOR MACHINE CUTTING TIP TIP CLEANIN HAND CUTTING TIP
CIRCULAR CUTTING ATTACHMENTProduct Number Description
82HC26SL Lighter for oxy-gas systems
82HC26L Flints (5 pcs)
LIGHTER WITH FLINT
Product Number Description
82HCI62X Wrench for nuts
WRENCH
Product Number Description
82HCAPS010 Goggles for oxy-gas systems
GOGGLES
HARRIS Welding Accessory
Oxy-Welding Hose
233Liability: All information in this catalog is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes: Consult information on Welding Safety Sheet, available upon request.
Liability : All information in this data sheet is based on the best available knowledge, is subject to change without notice and can only be considered as suitable for general guidance. Fumes : Consult information on Welding Safety Sheet, available upon request.18
Notes
234