DELTA^Q
SALES AND
APPLICATION
DELTA^Q
DELTA^Q
DELTA^Q
DELTA^Q
DELTA^Q
DELTA^Q
DELTA^Q
DELTA^Q
AP40 SERIES
AXIAL PISTON PUMPS Plant Location and Mailing Address
14233 West Road
Houston, Texas 77041
Website: www.deltaq.com
Email: [email protected]
Phone: (281) 807-1840 or (800) 650-3110
Fax: (281) 807-4457
AP 40 B 1 B 4 C 2 R 100
40 D Remote Load sense w/170 psi standby (4)
38 CA
35 M
30 CB
27 CC
25 PA
16 PB
Q
B R
T
1 W
2
3
4 1
5
2
6
7 3
8
17 6
18
19 7
20
21
10
B
C
13
1
4
5 R
9 L
A
B
C
CAY
CAX
* Red Denotes New Parts
SAE "C" Spline
SAE "C" Keyed - SAE "A" Spline rear drive
Short Differential (50 psi)
Torque Limiter (use with 'T' control)
ADAPTER: (Mounting)
(Use #3 cover and "B" flange)
SAE "BB" Spline - SAE "A" Spline rear drive
SAE "C" Keyed - SAE "BB" Spline rear drive
SAE "C" Keyed
SAE "BB" Spline
2 Spool CAY except w/Bypass (1 or 4)
Load Sense w/170 psi min standby (4)
NOTE: Standard Setting for Compensator is 2500 psi,
unless otherwise notated on order.
2 Spool Adj Press Comp & Adj Load Sense(1 or 4)
Pressure Settings
Assigned by factory for special variations
ROTATION: (viewed from shaft)
5
Counterclockwise
Dual Pressure Compensator (1 or 4)
Pressure Compensator (1 or 4)
Clockwise
Flow Limiter
VARIATION CODECONTROLS: (Required Construction in parenthesis)
MODEL/DISPL:
SAE "B" Spline
SHAFTS:
CONTROLS, cont'd:
2.7 Cubic Inch
2.5 Cubic Inch
Adj. Load Sense, Adj Press Comp (1 or4)
3.8 Cubic Inch
Loading 24 VDC (1 or 4)
Same as #3 with Min/Max vol. stop adj
COVERS:
REAR PORT, 4 Bolt Flange
Same as #3 except with rear drive SAE "B" drive
SIDE PORT, SAE 4-bolt flange code 61
Same as #2 with Min/Max vol. stop adj
Note: Use with shafts 17, 18, 19, 20 or 21
(Use #3 cover and "C" flange)
(Use #3 cover and "C" flange)
Shafts with rear drives:
SAE "C" Spline - SAE "A" Spline rear drive
Long Differential (350 psi)
SAE "BB" Spline - SAE "B" Spline rear drive
SAE "C" Keyed - SAE "B" Spline rear drive
CONSTRUCTION:
SAE "B" two bolt
1.6 Cubic Inch
3.0 Cubic Inch
3.5 Cubic Inch
Torque Limiter w/ Press Comp (5)
Standard Design with reduced noise level
SERIES:
Un-Loading 24 VDC (1 or 4)
Un-Loading 12 VDC (1 or 4)
Cover Plate
Loading 12 VDC (1 or 4)
Inlet 1 1/2" OD Flange per SAE J518C Code 61
REAR PORT, SAE O-Ring Ports
Inlet 1-7/8-12UN-2B(#24), Outlet 1-5/16-12UN-2B(#16)
Outlet 1" OD Flange per SAE J518C Code 61
Inlet 1 1/2" OD Flange per SAE J518C Code 61
Note: Rear "A" pad not available
Same as #10, except with Min/Max Vol Stops Adj.
Outlet 1" OD Flange per SAE J518C Code 61
(Use #3 cover and "B" flange)
SAE "C" two & four bolt
SAE "C" Spline - SAE "B" Spline rear drive
SAE "C" Spline - SAE "BB" Spline rear drive
SAE "B" Spline - SAE "A" Spline rear drive
Torque Limiter w/ Load Sense (5)
Flow Limiter
Load Sense w/350 psi min standby (4)
Note: Rear "A" pad not available
4.0 Cubic Inch ( 65.5cc)
ADJ. 2 SPOOL CONTROL