Analytical characterisation of nanoscale zero-valent iron: Amethodological review
Author
Chekli, L, Bayatsarmadi, B, Sekine, R, Sarkar, B, Shen, A Maoz, Scheckel, KG, Skinner, W,Naidu, R, Shon, HK, Lombi, E, Donner, E
Published
2016
Journal Title
Analytica Chimica Acta
DOI
https://doi.org/10.1016/j.aca.2015.10.040
Copyright Statement
© 2016 Elsevier. Licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International Licence (http://creativecommons.org/licenses/by-nc-nd/4.0/)which permits unrestricted, non-commercial use, distribution and reproduction in any medium,providing that the work is properly cited.
Downloaded from
http://hdl.handle.net/10072/382403
Griffith Research Online
https://research-repository.griffith.edu.au
1
Analytical characterisation of nanoscale zero-valent iron: An
illustrated methodological review
L. Chekli, a, b B. Bayatsarmadi, c R. Sekine, d B. Sarkar, b, d A. Maoz Shen, d K.G. Scheckel, e W. Skinner, f
R. Naidu, b, d H.K. Shon a, b E. Lombi, d and E. Donner, b, d
a School of Civil and Environmental Engineering, University of Technology, Sydney, Post Box 129,
Broadway, NSW 2007, Australia.
b CRC CARE, PO Box 486, Salisbury, SA 5106, Australia.
c School of Chemical Engineering, The University of Adelaide, Engineering North Building, Adelaide,
SA 5005, Australia.
d Centre for Environmental Risk Assessment and Remediation, University of South Australia, Building
X, Mawson Lakes Campus, SA 5095, Australia.
e U.S. Environmental Protection Agency, National Risk Management Research Laboratory, Land
Remediation and Pollution Control Division, 5995 Center Hill Avenue, Cincinnati, OH, USA.
f Ian Wark Research Institute, University of South Australia, Building IW, Mawson Lakes Campus, SA
5095, Australia.
*Corresponding author: Email: [email protected]; Phone: (61) 8 8302 6267.
Abstract Zero-valent iron nanoparticles (nZVI) have been widely tested as they are showing significant
promise for environmental remediation. However, many recent studies have demonstrated that
their mobility and reactivity in subsurface environments are significantly affected by their tendency
to aggregate. Both the mobility and reactivity of nZVI mainly depends on properties such as particle
size, surface chemistry and bulk composition. In order to ensure efficient remediation, it is crucial to
accurately assess and understand the implications of these properties before deploying these
materials into contaminated environments. Many analytical techniques are now available to
determine these parameters and this paper provides a critical review of their usefulness and
limitations for nZVI characterisation. These analytical techniques include microscopy and light
scattering techniques for the determination of particle size, size distribution and aggregation state,
and X-ray techniques for the characterisation of surface chemistry and bulk composition. Example
characterisation data derived from commercial nZVI materials is used to further illustrate method
strengths and limitations. Finally, some important challenges with respect to the characterisation of
nZVI in groundwater samples are discussed.
Keywords: zero-valent iron nanoparticles, characterization techniques, particle size, surface
chemistry, bulk composition, groundwater remediation.
2
1 Introduction
In recent years, manufactured nanoparticles (MNPs) have attracted increasing interest for their
potential applications in the treatment of contaminated soil and water. In comparison to traditional
macro- and micro-scale materials, MNPs possess significantly higher surface-to-volume ratios, which
frequently translate into unexpected surface effects and unique beneficial properties. In addition, by
virtue of their small size, MNPs can potentially be used directly in the field for in situ treatment via
injection at almost any location and depth in soil and groundwater systems [1]. Ideally, for this type
of application, MNPs are expected to feature several key properties including: (i) high reactivity for
the removal of targeted contaminants; (ii) high mobility in porous media (i.e. aquifers, soil); (iii) high
reactive longevity after injection and (iv) low toxicity to the biota in the surrounding environment
[1]. These properties are the main drivers when designing MNPs for the purpose of soil and
groundwater remediation. However, it is quite clear that in practice some of these properties are
difficult if not impossible to achieve simultaneously. For instance, high reactivity usually translates to
short longevity, and potentially greater ecotoxicological impact. In addition, these nanoparticles
must also be produced and delivered at a cost that remains sufficiently low to compete with
conventional technologies.
Due to their purportedly low cost, highly reactive surface sites and high in-situ reactivity, the most
widely studied MNPs for environmental remediation are nanoscale zero-valent iron (nZVI) [2-4].
Although most of the lab-scale, pilot-scale and field demonstration studies targeted soil and
groundwater remediation, nZVI has also been successfully applied for the stabilization of biosolids
[5], the removal of phosphorus [6, 7], the decoloration of dyes [8, 9], as a membrane anti-fouling
agent [10] and for the treatment of nuclear waste, explosives and herbicides [11-13].
Many studies suggested a core-shell structure for nZVI [14, 15] as illustrated in
Figure 1. The core consists primarily of zero-valent iron while the mixed valent oxide shell resulted
from the oxidation of the core metallic iron [16]. nZVI materials have been shown to exhibit high
3
reactivity in remediating aquifers contaminated by non-aqueous phase liquids (NAPL) and many
other hazardous compounds [3, 17, 18].
Figure 1
Effectively delivering the nZVI to the contaminant source zone is essential for the success of in situ
nZVI remediation. However, there are currently a number of issues limiting the potential
effectiveness of nZVI for this application. In fact, many laboratory and pilot-scale field studies have
demonstrated that the mobility and reactivity of nZVI are substantially limited in natural porous
systems such as soils and also groundwater aquifers [19-22]. The limited mobility and reactivity can
be explained by three basic mechanisms [23-25]:
• Due to their magnetic properties [26], nZVI particles have a natural tendency to aggregate
which generates significant losses in reactivity and decreases environmental mobility [27];
• As nZVI are prone to surface oxidation, the formation of corrosion product precipitates
(including Fe(OH)2, Fe(OH)3, Fe3O4, Fe2O3, FeOOH, Fe5HO8.4H2O and green rusts)
considerably limit direct Fe0-contaminant interactions [1].
• Due to interaction with the subsurface environment (mainly via attachment to mineral
surfaces and carbonaceous materials or microbial removal), nZVI may rapidly become inert
and relatively immobile [19].
These different factors (i.e. magnetic characteristics, tendency to aggregate, surface oxidation and
interaction with the environment) and related limitations mainly depend on nZVI properties such as
particle size, surface charge, bulk composition and surface chemistry. Furthermore, these properties
change with time due to the reactive nature of the materials. Therefore, it is essential to thoroughly
characterise newly developed products when reporting results in the literature, and also to compare
the characterisation results for commercial products with the manufacturers’ specifications.
Although some studies have previously focused on the characterisation of nZVI [28, 29], it is
increasingly recognised that the characterisation approaches used for MNPs are frequently
4
inadequate and/or underdeveloped. Moreover, multiple and complimentary analytical methods are
needed [30] as the validity and accuracy of some results may be inadequate under some conditions
[31]. The purpose of this review is to present the different analytical tools available to characterise
the different properties of nZVI and to discuss their advantages and limitations. Properties taken into
consideration include particle size, particle charge, bulk composition and surface chemistry.
Examples of characterisation methods of commercial nZVI/ZVI will be also provided. Finally, the
challenges of characterising nZVI in groundwater will be also discussed.
2 Particle size, size distribution and aggregation state analysis
Particle size, size distribution and aggregation state are important parameters to evaluate before
deploying nZVI in the subsurface environment to ensure efficient site remediation. Many studies
have demonstrated that both the reactivity and mobility of metal nanoparticles can be dependent
on particle size [14, 32, 33]. For instance, a recent study by Signorini et al. [34] demonstrated that
the composition of the oxide shell, which significantly impacts on nZVI reactivity [35], is influenced
by the size of the particle. Another important characteristic of nZVI particles that can impact on their
remediation efficiency is their strong tendency to aggregate due to their magnetic properties and
tendency to remain in the most thermodynamically favourable state [36, 37]. Importantly, the
formation of highly aggregated particles will reduce the available reactive surface sites compared to
dispersed nano-sized particles [14].
Several analytical methods are available to measure the particle size, size distribution and
aggregation state of a sample. In the case of nZVI, most published studies rely on one single method;
primarily using transmission electron microscopy (TEM) [14, 38, 39] or a combination of TEM with
one other size-measurement technique [21, 40-44]. However, many recent studies have emphasised
the importance of using a multi-method approach when characterising nanoparticles to ensure the
accuracy of the characterisation data [45, 46]. Analytical methods suitable for providing particle size
data are presented and discussed below, together with some nZVI demonstration data.
5
2.1 Microscopy techniques
Microscopy techniques provide some of the most direct methods for MNP characterisation; enabling
the determination of fundamental parameters such as size, shape and aggregation state by direct
visualisation. Traditional optical microscopes do not offer adequate spatial resolution: they are
diffraction limited (for visible light d ≈ λ/2 ≈ 250 nm), so electron microscopy techniques are
required to examine MNPs at the single particle level. The acquired images can be post-processed to
obtain a number-weighted size distribution of the MNPs that can assist in confirming the results
obtained from other bulk size-measurement techniques (e.g. Dynamic Light Scattering – DLS). As
microscopy methods are effectively single particle counting methods, a large number of particles
need to be analysed in order to acquire statistically representative results. The required number of
particles to be analysed is dependent on the distribution and the desired accuracy [47], but is
typically in the several hundreds to thousands of particles [48, 49]. This can be largely automated by
the use of image processing programs such as ImageJ [50]. However, some manual intervention is
often necessitated by the limited ability of programs to recognise dimers or larger aggregates, even
with the use of various boundary metrics (e.g. circularity). Furthermore, appropriate sample
preparation is critical in determining accurate sizes and distributions from these methods. For the
characterisation of nZVI, the most commonly applied microscopy techniques are TEM [14, 38, 39],
scanning electron microscopy (SEM) [37, 51, 52] and atomic force microscopy (AFM) [53-55].
2.1.1 Transmission electron microscopy (TEM)
Transmission electron microscopy is a single particle characterisation technique that uses an
accelerated beam of electrons to illuminate thin samples (typically <100 nm). In the commonly
applied bright-field TEM, the transmitted electrons produce a 2D projection of the specimen on to
an imaging device such as a charge coupled device (CCD). Due to the short de Broglie wavelength of
the accelerated electrons, TEM can image particles beyond the diffraction limit of light microscopies
and provide direct visual information about size, shape and aggregation state; as well as information
6
about crystallinity and lattice spacing when using high resolution TEM [56-58]. This ability to directly
image nanoscale materials such as nZVI is a powerful advantage over other methods of particle
characterisation such as DLS or FFF, and TEM and its variants have been widely used for nanoparticle
characterisation [28, 59-61]. For example, while DLS can be used to derive the hydrodynamic
diameter of particles (see Section 2.2.1), this technique requires an inherent assumption that the
diffusing “particles” are spherical, which may not necessarily be the case. TEM can offer irrefutable
evidence of the nZVI core shape and aspect ratio that can assist in the appropriate interpretation of
complementary data. It is also important to note that TEM measures the hard particle limits defined
by the iron components (in the case of nZVI), rather than the hydrodynamic diameter which extends
to include the adsorbed organic stabilisers with low TEM contrast. On the other hand, inorganic
surface layers can also be examined, and this may be very useful in examining core-shell structures
of nZVI such as oxide minerals [35, 38, 62] (Figure 2), or palladium used for enhancing nZVI
environmental stability or catalytic reactivity [63].
Figure 2
Other modes of TEM can be used to provide additional physicochemical information about the
samples. For example, dark-field imaging, which produces contrast by electron density differences,
may reveal the individual particles within nZVI agglomerates linked by oxide layers [63, 64] , and
even internal grain structures [59]. X-ray energy dispersive spectroscopy (XEDS) can provide further
details, such as semi-quantitative information about the elemental composition of a collection of
nZVI particles, and can be used to map single particles with scanning TEM (STEM) – XEDS (Figure 3),
which may be valuable in assessing the spatial distribution of bimetallic nZVI dopants, or the
mechanisms of reactions and effectiveness of remediation at the nanoscopic level [38, 61, 63, 65].
One of the advantages of TEM-XEDS is that the thin specimens lead to greater spatial resolution than
that achieved with SEM-XEDS, as the large sub-surface interaction volume can limit the SEM-XEDS
resolution at high voltages (see Section 2.1.2).
7
Figure 3
Sample preparation is one of the challenging aspects of TEM analysis. For the determination of
particle size distributions using TEM, the specimen needs to be thin (typically < 100 nm) and should
ideally consist of well separated monolayers of particles in a uniform focal plane. The microscopes
operate under high vacuum and the samples must be dried prior to analysis. This presents a
challenge due to the high reactivity of nZVI with oxygen under normal atmospheric conditions and
the magnetic properties of nZVI also complicate matters. Furthermore, slow drying processes can
induce aggregation or agglomeration as a result of the increase in absolute particle concentrations
and increased ionic strength. Sample preparation techniques are thus ideally fast (e.g. flash drying)
and should avoid contact with oxygen rich atmospheres by the use of anaerobic chambers or
vacuum desiccators. One approach may be to immobilise nanoparticles on to carbon coated grids
with a functionalised polymer (e.g. poly-L-lysine – see later example for SEM, Figure 4 e), from which
excess sample can be removed prior to drying, and the immobilised fraction bound to the surface
can be dried without the risk of inducing aggregation. There is also need for caution to minimise
damage to the samples from the high energy electrons, which may for example, contrary to
expectation, induce oxidation of the outer layers of nZVI [57, 66]. Therefore, it is recommended that
acquisition parameters be optimised in regions that are close to, but not directly aligned with, the
actual regions of interest. Finally, once prepared, samples should be stored appropriately in a dry,
inert environment (e.g. a vacuum desiccator) and analysed within a short timeframe to minimise
transformation artefacts [67].
2.1.2 Scanning electron microscopy (SEM)
Scanning electron microscopy (SEM) is a technique whereby finely focused electron beams are raster
scanned to image the surface of samples. Rather than imaging the transmitted electrons as in TEM,
SEM utilises electrons that are generated when the beam interacts with the sample surface. Thus, it
is a surface sensitive imaging technique. Three phenomena are routinely used in different modes of
8
analysis: secondary electron (SE) mode, backscattered electron (BSE) mode, and XEDS mode (as in
TEM).
SEM have been used to examine the aggregation state, surface morphology [53, 68, 69] (see also
Figure 4), and spatial distribution of nZVI on solid substrates [69-72], and, less frequently, for size
determination. While SEM is generally more accessible than TEM (i.e. more common in research
laboratories), spatial resolution is poorer in SEM than in TEM, even for SEMs with a field-emission
source (FEG-SEM). This is dependent on several factors such as the acceleration voltage of the beam,
working distance and the atomic number and density of the material. While the best SEMs can
achieve sub-nanometre resolution in SE/BSE modes and resolve sub-100 nm MNPs in X-ray imaging
modes, in practice, accurate size determination with commonly available microscopes using SE
mode is limited to ca. 10 nm and slightly worse for BSE mode. SEM-XEDS images have even higher
limits for accurate sizing due to the large sub-surface interaction volume, which is highly dependent
on the beam energy and sample density (Figure 5). Typically, a beam energy approximately twice
that of the desired X-ray emission line is used. For Fe L-edge emission (6.4 keV) this is 12.8 keV, and
a beam of this energy at a spot size of 1 nm would provide a lateral resolution of ca. 0.5 µm. Besides,
unlike TEM, SEM cannot accurately determine the oxide layer thickness in nZVI, unless for example,
the particles have a thick oxide layer, such as that more commonly found on ZVI microparticles. In
such cases, comparing the BE and BSE images may reveal regions of different electron density
(Figure 4c), or XEDS may be acquired for qualitative element/composition identification.
Figure 4
Figure 5
Sample preparation for SEM is comparatively easier than for TEM because the specimens do not
need to be so thin. However, as with TEM, care is still required in minimising exposure to air, while
ensuring that the samples are dry. Furthermore, they need to be electrically conductive: non-
conductive samples require surface coating via sputtering or evaporative processes to impart surface
conductivity and this may be necessary for samples with high organic stabiliser content.
9
2.1.3 Scanning probe microscopy (SPM)
Scanning probe microscopy (SPM) is a technique that utilises a sharp tip (i.e. probe) to scan over the
surface of a sample. There are many types of SPM available including for example, atomic force
microscopy (AFM), scanning tunnelling microscopy (STM) and scanning near-field optical microscopy
(SNOM or NSOM); however, the application of SPM to nZVI in the literature is limited. AFM is
capable of providing quantitative information about the particle height (≈ size, if spherical) and
morphology of nZVI [73, 74], and its aggregation state or distribution over a flat surface. Unlike
conventional TEM and SEM, AFM can be conducted under a wider range of conditions (e.g. in
vacuum, liquid or moist conditions, or in other controlled environments), and as it does not involve
the use of high energy electron beams, it could be advantageous in the case of nZVI characterisation
with respect to minimising sample damage and oxidation. For conductive samples, STM can be used
to image the topography at atomic resolution by exploiting the tunnelling current generated
between an electrically biased sharp tip and the sample surface. It has been applied to study the
change in surface profiles after reaction with Cr(III) and Se(IV), where they found that roughness
(protrusions) on the surface had smoothed out as a result of the reaction [75].
However, most of these techniques are less commonly employed as they tend to be more
specialised and therefore are often not available in many laboratories.
2.1.4 Other microscopy methods with potential applications
Several novel method developments have recently been made with potential applications in
nanomaterials analysis. For example, hyperspectral dark-field imaging with the aid of multivariate
classification algorithms [76] were able to provide information on the size, aggregation state, and
composition of Ag, CeO2 and TiO2 nanoparticles when these were analysed in representative
environmental media. This technique may potentially enable the examination of iron-based
nanoparticles in environmental waters, although there may be difficulties arising from the presence
of naturally occurring colloids which may also contain iron. Furthermore, light microscopy has been
10
revolutionalised in the last decade with the advent of super-resolution microscopy (SRM) that offers
spatial resolution surpassing the classical diffraction limit [77-79]. While most of these require
fluorescence labelling that may not be compatible with nZVI, method such as scanning near-field
optical microscopy (SNOM) that do not require labelling may have potential in nZVI imaging. Finally,
helium ion microscopy (HeIM or SHOM), is also an imaging technique that is becoming accessible,
where He ions are used as the probe instead of electrons [80]. This results in improved surface
sensitivity (reduced interaction volume), better spatial resolution (shorter de Broglie λ) and larger
depth of field (lower beam divergence), and has been used to examine the surface deposition
morphologies of nanocluster deposits [81].
2.2 Light scattering techniques
Light scattering techniques are commonly used to determine the size and aggregation behaviour of
nanoparticles in suspensions [82]. The light source can be laser light, X-rays or neutrons and the
choice of the light source will depend on the size range and particle compositions of the sample to
be analysed [32]. Nowadays, dynamic light scattering (DLS) is the most commonly utilised techniques
for sizing nanoparticles [83] as it offers several advantages, such as rapid analysis, simple operations
and minimum perturbation of the samples [84]. Other commonly used light scattering techniques
for the characterisation of MNPs include small angle X-ray scattering (SAXS) which enables the
characterisation of both monodispersed and polydispersed samples, laser-induced breakdown
detection (LIBD), which is able to detect trace amount of NPs in aqueous suspensions, and static light
scattering (SLS), also called multi angle (laser) light scattering (MALS or MALLS) which can provide
valuable information on particle shape factors when combined with DLS [32]. To date, few studies
have reported the use of light scattering techniques to measure the size and aggregation behaviour
of nZVI [21, 22, 26, 40, 43, 85-90]. This is largely due to inherent analytical challenges. The detailed
discussion about light scattering techniques below is limited to DLS, since this is the only light
scattering technique used for characterising nZVI.
11
2.2.1 Characterisation of nZVI using dynamic light scattering
Table 1 summarises results from all of the studies which have used DLS to characterise nZVI and
places particular focus on the reported methods of sample preparation and data processing.
DLS measures the diffusion coefficient of particles by correlating the fluctuations of the scattered
light intensity (i.e. coming from the Brownian motion of the particles and from the fact that
neighbouring particles can have constructive or destructive interference on the scattered light
intensity in a certain direction) over time [32]. The Z-average hydrodynamic diameter can then be
calculated by applying the Stokes-Einstein equation. Detailed information on this method, including
physical principles, mathematical models, and limitations can be found elsewhere [91]. The
limitations of this technique mainly relate to the analysis and interpretation of the data obtained,
especially for polydispersed samples [91]. DLS is known to be very sensitive to larger particles and a
very small number of large particles sedimenting during the analysis (e.g. due to aggregation
processes) can induce biased results [46]. This is mostly due to the strong particle size dependence
of the scattering intensity. In fact, according to the Rayleigh approximation, the intensity of light
scattered by a particle is proportional to the sixth power of its diameter. This causes large particles
to scatter far more light than small particles [92]. Therefore Z-average or intensity values tend to
overweight the contribution of larger particles/aggregates [46]. In addition, for multimodal size
distributions, the conversion of the autocorrelation function to a diffusion coefficient poses a major
mathematical problem (i.e. small variations can give large deviations in the output). For this reason
but also due to the fact that the signal from larger particles dominates over smaller ones, a common
rule is that DLS cannot be applied to samples with polydispersity indices above ~1.5–1.7 [32].
However, in most studies, there is no information regarding the polydispersity index (PDI) of sample;
information that can be extracted from the analysis of DLS results and which can be very useful to
determine the best dispersion strategies to adopt for a specific sample.
12
Previous studies using nZVI have demonstrated that this class of nanoparticle has a great tendency
to aggregate, especially when particles are not surface stabilised (i.e. coated). This often results in
samples having high polydispersity with the presence of substantially large aggregates [19-22, 36,
93]. In order to obtain more accurate and reliable data with DLS, the polydispersity of the sample
can be reduced by using different sample preparation methods and data processing. Sample
preparation methods are documented in Table 1. The most simple and applied sample preparation
method to break down nanoparticle aggregates (i.e. aggregates formed during storage) is sonication
[22, 26, 40, 85, 86, 88]. Different sonication times may be used depending on the aggregation state
of the sample prior to measurement. Honetschlägerová et al. [85] applied different sonication times
and found that above 15 minutes, no further change was observed. Saleh et al. [22] combined
sonication with an ultrasonic probe for 30 minutes and rotator mixing for 72 hours and obtained
fairly stable samples. However, based on the studies presented in Table 1, it is very difficult to reach
a conclusion on the effect of sonication time since there are too many parameters which differ
among these studies. In fact, in some cases, sonication is not the only employed sample preparation
method (e.g. in some studies, samples are diluted prior to measurement) and thus it is difficult to
evaluate which of the applied method has the most impact on sample stabilisation. Moreover, these
studies have used different particle concentration (i.e. from as low as 5 mg L-1 to 2.5 g L-1), different
surface coatings (i.e. bare nZVI, polymer or surfactant stabilised nZVI) and different chemical
conditions (i.e. different pH and ionic strength), which are all known to influence particle
aggregation. This suggests that, for DLS in particular, standard sample preparation protocols need to
be developed with the prospect to combine data from heterogeneous sources into integrated and
harmonized databases.
The particle concentration of the sample is also important and this may need to be adjusted by
dilution. In fact, for charged particles, the electrostatic forces arising between particles can have an
effect on their diffusive behaviour and this effect is concentration dependant, with a maximum
occurring at a point called “gel-formation” [32]. Phenrat et al. [26] tested different nanoparticle
13
concentrations and found that aggregation rate increased with increasing particle concentration.
This issue can generally be overcome by diluting the sample (e.g. with MQ water) but this will affect
the aggregation state of the sample. It is quite clear though that due to the limitations of DLS, this
technique cannot be successfully used to assess primary particle size in commercial nZVI
concentrated products as they are generally too concentrated. Hence, if the purpose of the analysis
is to measure the aggregation behaviour of the sample, then it is more relevant to report the
diffusion coefficient rather than the size, without diluting the sample.
As aggregation of charged particles is also pH-dependant with maximum aggregation occurring at
the point of zero charge (PZC) (i.e. around pH 8 for nZVI [28]), reducing or increasing the pH far away
from the PZC could be one way to form stable dispersions. Kim et al. [88] investigated the
aggregation behaviour of two polymer-coated nZVI materials at two different pH values (pH 6 and
pH 8) and found that aggregation increased with decreasing pH.
Pre-fractionation of the sample can also be used to obtain more accurate characterisation. Phenrat
et al. [86] prepared three different intrinsic particle size distributions by sequential, gentle
sedimentation. They found a bimodal size distribution for unfractionated samples while samples
collected in the supernatant showed a monomodal size distribution with smaller particle size.
Another way to reduce the polydispersity of the sample which has not yet been tested for nZVI is to
couple DLS with a size fractionation technique such as Flow Field-Flow Fractionation (FlFFF). In this
way, more complex characterisation of size fractions can be potentially achieved [94]. To date, only
one study has been reported on the use of this combination for the characterisation of C60
nanoparticles [95].
As discussed previously, the data derived from DLS measurements are intensity-based distributions
or averages which tend to overweight the contribution of larger aggregates and hence overestimate
particle size [46]. Nowadays, mathematical conversion to volume or number distributions are quite
14
often used as they can correct for overestimation to some extent [96]. However, these conversions
should be made only with good knowledge of the particle shapes, polydispersity and relevance of
other key assumptions [97].
It can be clearly seen from the above discussion that many dispersion strategies have been
employed and tested in an attempt to reduce the polydispersity of the studied samples. Results from
Table 1 shows that different dispersion strategies resulted in different findings in terms of size and
sample polydispersity (i.e. monomodal or bimodal size distribution). Because of the various
conditions used in these studies (i.e. different synthesis method, different particle concentration,
different surface coating, different dispersion media), it is very difficult to draw conclusion on the
accuracy of the results and more importantly to compare the results from different studies.
Therefore, a general effort should be made to develop standardised procedures for sample
preparation and dispersion in order to obtain nanoparticle characteristics (e.g. size and dispersion)
that can be easily comparable. Furthermore, the development and synthesis of standard ZVI
nanoparticles from commercial laboratories for the purpose of instrument calibration and validation
of developed analytical methods should be the focus of future research.
Table 1
3 Bulk composition and surface chemistry analysis
Bulk composition and surface chemistry are also important characteristics that need to be rigorously
determined in any nZVI materials during experimentation and before they are deployed into the
environment. In fact, the metallic iron content as well as the composition of the oxide shell at the
time of delivery will have a substantial impact on the nZVI performance [98, 99].
Among different analytical techniques which have been applied to determine these properties, X-ray
diffraction (XRD) [28, 31, 35, 52, 53, 100-107], X-ray adsorption spectroscopy (XAS) [28, 35, 64, 100,
107-109] and X-ray photoelectron spectroscopy (XPS) [16, 28, 31, 35, 70, 101, 102, 104, 106-108,
110-112] are the most common X-ray techniques used to characterise nZVI.
15
3.1 X-ray diffraction (XRD)
X-ray diffraction (XRD) is a simple, versatile, non-destructive and comparatively inexpensive
technique for identifying the phases of crystalline materials. Broad applications include assessment
of percentage crystallinity; identification of fine-grained minerals such as nanoparticles, nano-clays
and mixed layer clays that are difficult to distinguish optically; determination of unit cell dimensions;
and evaluation of sample purity. If the sample is finely ground and homogenised; the bulk
compositional chemistry of the material can be obtained through XRD [35, 100, 103, 106, 113, 114].
The principle of XRD is based on Bragg's Law (nλ = 2d Sin θ; where λ is the wavelength of the X-rays,
n is the order of diffraction, d is the spacing between consecutive parallel planes of a crystal and θ is
the complement of the angle of X-ray incidence) in which monochromatic X-rays constructively
interfere with a crystalline sample and produce diffracted X-rays. More detailed information on this
method can be found elsewhere [115, 116]
Table 2 provides a summary of the different studies which used XRD for nZVI characterisation. nZVI
samples often provide very broad XRD peaks due to the short range order structure (i.e. amorphous
nature) of the iron nano-phases, including the Fe(0) phase [53, 113, 117]. However, a recent study
has found that ultrasound assisted synthesis can provide more crystallinity to Fe(0) [118]. Peak
broadening generally occurs due to surfactant artefacts in surfactant stabilised nZVI samples [37,
119], sample ageing [120] or reactions with contaminants [53, 68, 121-125]. Some polymers (e.g.,
polyacrylic acid, polyvinylpyrrolidone) stabilised nZVI samples may show no XRD peak of iron phases
due to the combination of amorphous and non-crystalline phases and surfactant artefacts [119].
Previous studies focusing on the green synthesis of nZVI also found samples produced with green
methods show no XRD peaks, especially the characteristic peak of zero-valent iron (α-Fe) (i.e. 44.9°
2θ) indicating that the green nZVI are amorphous in nature [126-128]. These results suggested that
XRD may not be suitable for all nZVI products, especially those coated with organic polymers or
produced with green synthesis methods, which is one of the limitations of this approach.
16
For determining the crystal structure and quantifying the different phases, additional advanced
numerical technique such as Rietveld refinement is often required. However, quantification by XRD
is usually not reported because of the uncertainties related with the presence of amorphous and
nano-crystalline materials and this technique is generally employed only for identification of major
crystalline phases. This method can also be applied to indirectly analyse the composition of major
elements (constituting the crystalline phases); however, the sensitivity is much lower than with
other elemental analytical techniques such as inductively coupled plasma mass spectrometry (ICP-
MS). The detection limit of an individual phase present in a mixed material is about 2 – 3 % and this
quantification is limited to well crystalline phases. In most previous studies where XRD was used as
an nZVI characterisation tool, the researchers were confined only to identification of iron phases and
evaluation of crystallinity (Table 2). Iron phases in nZVI samples identified by XRD patterns include
Fe0, ferrihydrite, magnetite (Fe3O4)/maghemite (ɤ-Fe3O4), lepidocrocite (ɤ-FeOOH) and wuestite
(FeO) (Table 2). The presence of Fe0 and oxides and/or hydroxides of iron support the core-shell
structure model of nZVI [64]. The extent of oxides/hydroxides present in an nZVI sample depend on
its synthesis and storing conditions, duration of ageing, presence of other chemical
elements/compounds, etc. (Table 2).
Valuable information about the particle size of a material might be derived from XRD patterns of
crystallites less than about 100 nm in size. These nano crystallites provide appreciable broadening
(FWHM – Full Width at Half Maxima) of the XRD peaks. By entering a corrected peak broadening
value (corrected for instrumental contribution and crystal strain; β) in Scherrer’s equation (D = 0.9
λ/β Cos θ) the average particle size can be estimated. The size can be estimated from a single
diffraction peak if particle stress is absent, but several diffraction peaks should be involved if stress is
present. However, most published studies using XRD for nZVI characterisation have not used this
method for nZVI particle size determination (Table 2), probably because of the ambiguity in the
reasons for peak broadening. Rather TEM, SEM or DLS is more commonly used for this purpose (see
Sections 2.1.1., 2.1.2. and 2.2.1.).
17
Sample oxidation of nZVI can also occur during the XRD run time since a good quality pattern takes
about 40 minutes to obtain when scanning in the range 10o to 90o 2θ with a step size of 0.013o and
around 100 sec per step. Even short exposures to air of one minute or less can significantly affect the
speciation of nZVI [129], therefore an appropriate covering technique should be employed during
sample preparation in order to prevent the oxidation of nZVI during the test period. Also, samples
need to be prepared and stored under anaerobic conditions or an inert atmosphere prior to XRD
analysis.
Table 2
3.2 X-ray photoelectron spectroscopy (XPS)
X-ray photoelectron spectroscopy (XPS) is an ultra-high vacuum, surface sensitive technique in which
a sample is irradiated with X-rays of known energy and the kinetic energies of emitted
photoelectrons and Auger electrons are measured. Elements present are identified by the
characteristic binding energies, of their atomic orbitals, and determined from Equation 1:
h = BE + KE + Eq. (1)
where h is the incident X-ray energy, BE is the photoelectron binding energy, KE the measured
kinetic energy of the emitted photoelectron and is an instrumental work function (energy loss).
Typical X-ray source energies are <2000 eV (K line), with the commonest anodes being Mg (1253.6
eV) and Al (1486.6 eV), with monochromatic Al K sources fitted to high (spectral) resolution
instruments.
Useful for a wide range of materials and sample types [31, 130], XPS provides elemental
concentration and, for many elements, chemical environment and/or oxidation state information in
the top-most few nanometres of surfaces, whether organic [131] or mineral with inorganic [132] or
organic adsorbates [133]. Surface concentrations of elements, relative to the bulk concentrations,
can give valuable indicators of specific absorption of solution-borne species, while oxidation state
18
may suggest potential impacts of redox changes, re-mobilisation and bioavailability. In the context
of fine particles, the last is extremely important when examining toxicity (e.g. [134]). For particles
such as ZVI, XPS can monitor surface composition and chemistry as a function of time and
environmental exposure [31, 130, 135] (Table 3). Through the use of ion etching of surfaces and/or
examination of photoelectron escape depths, information about the thickness of particle coatings,
contamination or reaction layers may be gleaned [31, 129, 130, 136, 137] (Table 3).
Being an extremely surface sensitive technique, XPS does not provide information on the bulk
chemistry of nZVI particles. Also, for the same reason, it is absolutely imperative that nZVI materials
are maintained under anaerobic condition at all times during sample preparation and transfer into
the instrument as even a brief exposure to oxygen can cause oxidation of the nZVI surface which is
probed by XPS. This is often problematic or impractical unless the XPS loading port can be connected
to an anaerobic chamber.
3.3 X-ray adsorption spectroscopy (XAS)
X-ray adsorption spectroscopy (XAS) uses synchrotron radiation to obtain information about the
oxidation state, identity of nearest neighbours, bond length, coordination number and electronic
configuration of an element of interest in virtually any sample (see [138] for review). Using this
technique the valence and chemical state of Fe on both the particle surface and in the bulk volume
can be determined [28, 35, 106, 108] (Table 3).
One of the most important advantages of this technique is the possibility of speciation analysis in
any sample under almost any environmental condition (without the need of separating the element
of interest through an extraction procedure) [139, 140]. This is a particular advantage in the case of
nZVI as samples can be analysed as slurries (or frozen) or as dry powders as long as they are
mounted in a way that prevents their contact with oxygen. This is easily achievable by sandwiching
19
the sample between two layers of a material such as polyimide, which is virtually transparent to the
X-rays of interest.
On the other hand, the interpretation of XANES/EXAFS spectra can be very intricate and time-
consuming in samples with complex mixture of chemical species, because the spectra obtained
represent the weighted sum of all the species in the analysed volume [141]. Consequently, the
quantification of a very thin layer of oxidised Fe on the surface of nZVI particles, which is easily
detected by XPS, would be difficult to quantify by XAS unless it represented at least a few % of the
total Fe.
Table 3
4 Characterisation of commercial products
To demonstrate some of the advantages and limitations of the major techniques described above
we used them to characterise a number of commercial ZVI/nZVI products. Five different commercial
products with different physicochemical properties, including three powders and two slurries, were
examined. Major physical and chemical properties of the materials reported according to the
manufacturers’ specifications are shown in Table 4.
Table 4
All sample preparation steps for the following analyses were conducted under anaerobic conditions,
and anaerobic conditions were also maintained during analysis as detailed below.
DLS analysis was attempted using a Nicomp 280 instrument. In order to improve the dispersion of
the particles the samples were diluted up to 100 times in degassed milli-Q water and sonicated for
10-75 minutes. The samples were transferred under anaerobic conditions to cuvettes that were
subsequently sealed to prevent oxidation during analysis. Despite the dilution and sonication steps,
sedimentation of particles was visible in all samples during the analysis period. This may have been
prevented by combining different sample preparation methods in addition to dilution and
sonication. For instance, pre-fractionation of the sample to remove the larger aggregates has already
20
proved to be an efficient method to reduce the sample polydispersity [86, 142]. However, this
method would have been ineffective if the sedimentation of particles was caused by the non-surface
stabilisation of the manufactured nZVI, the pH and ionic strength of the solution which are both
known to favour the aggregation (or disaggregation) of nanoparticles or the oxidation of the ZVI
nanoparticles which can cause the formation of large corrosion products (even though the samples
were not in contact with air during sample preparation and analysis). Since DLS measurements are
based on the Brownian motion of the particles, evidence of sedimentation indicated that this widely
used characterisation technique would not produce reliable or reproducible results for these
materials. This stresses the need to develop standard sample preparation protocols for this
instrument which would help in the acquisition of reliable, accurate and comparable data among the
scientific community. These protocols should include essential parameters such as final particle
concentration, solution chemistry (i.e. pH, ionic strength) or the use of surface stabilisers to achieve
the adequate sample polydispersity for DLS analysis.
In order to further investigate the dispersion and morphology of the five commercial products, the
samples were then examined by SEM (FEI Quanta 450 FEG-ESEM operated at 20 kV). All samples
were prepared using ethanol to prevent the oxidation of nZVI/ZVI products during sample
preparation. Figure 6 shows SEM images of 2 commercialised ZVI products (i.e. one powder and one
slurry). It is clear from these images that both samples are highly polydispersed (i.e. from nanoscale
particles to micron scale aggregates) and the aggregates from the slurry sample (Figure 6b) exhibit
an open, porous morphology suggesting that these aggregates were formed under unfavourable
conditions (i.e. the total interaction energy between particles is positive which resulted in high
attachment efficiency).
Figure 6
XRD analysis was conducted in order to assess the relative proportion of ZVI in the materials and the
identity of any other major Fe species or Fe corrosion products. The XRD patterns were obtained,
21
using a PANalytical Empyrean X-ray diffractometer by capping the samples (prepared under
anaerobic conditions) with polyimide film in order to prevent oxidation during the analysis (Figure
7). The thickness of the polyimide film used was 8 µm, (note that thicker, 1 mm, polyimide film
obscured the diffraction region of the sample at 2θ values 10 – 30o).
Figure 7
The XRD quantification results indicated a significant disparity in the contents of ZVI and iron oxide-
hydroxide in the measured samples as compared to the values reported in the manufacturers’
specifications (Table 5). The oxide and hydroxide phases of iron in the samples included magnetite
(Fe3O4) and/or maghemite (ɤ-Fe2O3), lepidocrocite (ɤ-FeOOH) and wüstite (FeO) (Figure 7) [53, 143].
Zero-valent iron is characterised by peaks appearing at 2θ values of 44-45°; 65-66° and 82-85° [14,
15, 28, 39, 100, 101, 103, 113]. We note that the ZVI contents in some samples (P2 & P3) were
remarkably less than that specified in the manufacturers’ reports. This may be partly due to the
difficulty to quantify XRD data for nZVI as reported above or to oxidation of ZVI particles occurring
during storage and transportation. Therefore, alternative method to polyimide film should be tested
to find the best suitable method to prevent nZVI oxidation prior and during XRD analysis.
Table 5
Figure 8 shows the Fe 2p photoelectron emission spectra (Kratos - AXIS Ultra) of the five
commercially-available ZVI particles obtained for this study. Once again, we note that these
materials were prepared in an anaerobic chamber and an anaerobic transfer chamber was used to
transfer the materials into the XPS instrument, thus preventing oxidation of the products prior to
measurement. As can be seen, metallic Fe, Fe(0), was only present in the surface layers of samples
S1 and S2. No Fe(0) was evident on the surfaces of the other three products. The majority of
intensity contributions, however, derive from Fe(II) and Fe(III) associated with oxygen on all sample
surfaces [28, 31, 108, 113, 144, 145], with P1, P2 & P3 all apparently identical in Fe oxidation product
exposure.
22
Figure 8
XAS studies were conducted in quick-scan transmission mode at the Materials Research
Collaborative Access Team (MRCAT) beamline 10-ID, Sector 10, at the Advanced Photon Source of
the Argonne National Laboratory, U.S.A. The storage ring operated at 7 GeV in top-up mode.
Calibration was performed by assigning the first derivative inflection point of the absorption K-edge
of Fe metal (7112 eV), and each sample scan was collected simultaneously with an Fe metal foil. The
collected spectra were analysed using the Athena software program in the computer package
IFEFFIT [146] for data reduction and WinXAS 3.0 [147] for data fitting. The data were converted from
energy to photoelectron momentum (k-space) and weighted by k3 using WinXAS. Linear
combination fitting (LCF) was performed on the data using a dataset of reference spectra including
metallic Fe as well as a number of iron oxy/hydroxides minerals. Furthermore, extended X-ray
absorption fine structure (XANES) spectra were calculated over a typical k-space range with a Bessel
window. Fourier transforms were performed to obtain the radial distribution function in R-space.
Plotted R-space (Å) data are not phase shift corrected. The results of the LCF procedure (Table 6,
Figure 9) indicated that most of the Fe was present in metallic form in samples P1, S1 and S2; with
the remaining Fe in these samples present as magnetite and maghemite. In samples P2 and P3 most
of the Fe was oxidised, with maghemite, magnetite and wuestite dominating the Fe speciation. The
lower Fe(0) content as assessed by XAS in comparison to XRD (Table 4 and 5) are most likely due to
differences between these two techniques. XRD relies on the crystallinity of the phases investigated
(i.e. long-range structure) while XAS probes directly the core structure of the Fe atoms and it is
therefore less dependent on crystallinity. It is likely that the corrosion layer present on the nZVI
materials has a much lower crystallinity than the Fe(0) core. As a result the proportion of Fe(0) could
be overestimated by XRD. As sample P2 has a larger size, the underestimation of the corrosion shell
by XRD is expected to be lower in that case.
Table 6
Figure 9
23
Figure 10 shows the Fourier transformed radial distribution functions (RDFs) of the five samples and
an iron metal foil. The fit data (Table 7) shows the coordination parameters of Fe in the samples.
Metallic Fe is present in each sample and results of the Fe metal foil show the basic parameters
expected for Fe(0) with paths of Fe-Fe1 (CN: 8, R: 2.49Å), Fe-Fe2 (CN: 6, R: 2.87Å), Fe-Fe3 (CN: 12, R:
4.06Å), and Fe-Fe4 (CN: 24, R: 4.76Å), along with multi-scattering paths to accurately fit the
spectrum. The fitting of the Fe metal foil involved fixing the CN of each path determined by ab initio
calculations by FEFF8 and allowing atomic distance to float, resulting in R values close to theoretical
calculations (Fe-Fe1 – 2.4855 Å; Fe-Fe2 – 2.8700 Å; Fe-Fe3 – 4.0588 Å; and Fe-Fe4 – 4.7594 Å).
Despite LCF results indicating minor portions of Fe-III (oxy)hydroxides in samples P1, S1, and S2, the
EXAFS fitting was unable to accurately fit components for Fe-III (oxy)hydroxides. The transformed
RDFs represent the average of all signals in a given sample, which may inhibit identification of some
low quantity phases. The results for samples P1, S1, and S2 indicate the presence of Fe(0) as the
primary phase with CN and R values representative of the Fe metal foil and ab initio data noted
above. Samples P2 and P3 added complexity to the fitting process with the presence of oxidized iron
minerals. The LCF results of P2 indicate the presence of Fe(III) oxide minerals and Fe(0). The
components of Fe(0) metal in P2 (Fe-Fe1; Fe-Fe2; Fe-Fe3; and Fe-Fe4) align well with parameters of
the iron metal foil results. The Fe(III) mineral components of P2 yield an Fe-III-O path with CN of 6 at
1.94 Å and an Fe-Fe2 Oxide path with CN of 6 at 2.94 Å (Table 7). These fit parameters for the Fe(III)
mineral components in P2 align well with ab initio calculation for LCF determined minerals of
magnetite (FeIII-O – CN: 6, R: 2.00 Å; Fe-Fe2 Oxide – CN: 6, R: 2.89 Å), maghemite (Fe-III-O – CN: 6, R:
2.08 Å; Fe-Fe2 Oxide – CN: 6, R: 2.94 Å), and lepidocrocite (Fe-III-O – CN: 6, R: 1.99 Å; Fe-Fe2 Oxide –
CN: 6, R: 3.04 Å). The LCF results for P3 indicate the presence of wuestite (Fe-II-O) in addition to
Fe(III) oxide minerals and Fe(0). EXAFS fitting results (Table 7) for P3 demonstrate an additional path
of Fe-II-O with a CN of 6 at 2.19 Å relative to P2, which supports the presence of wuestite (Fe-II-O –
CN: 6, R: 2.15 Å). However, the Fe-Fe2 Oxide R value is larger than the 3.24 Å Fe-Fe bond distance in
wuestite and larger than the average second shell Fe-Fe distance of the oxidize Fe minerals
24
determined by LCF for P3 (magnetite, maghemite, and wuestite). Overall, the EXAFS fitting results
(Table 7) support the LCF information (Table 6) as well as visual evidence in Figure 10 where P1, S1,
and S2 possess similar RDFs to the Fe metal foil. The Fe metal foil peaks are observable in P2 in
addition to peaks associated with Fe-III (oxy)hydroxides. For P3, the Fe metal foil peaks are less
obvious and the presence of wuestite yields an RDF that is different than that of the other four
samples.
Figure 10
Table 7
These results indicate that in all cases the content of Fe(0) present in the materials was less than
that reported by the manufacturers. However, in three cases (P1, S1 and S2) both XRD and XAS
analysis showed that metallic Fe comprised the large majority of the materials with the rest
composed of magnetite, maghemite and lepidocrocite. In the case of the S1 and S2 materials, XPS
analysis showed that Fe(0) was present on the surface of the particles, while in the case of P1 the
lack of a peak indicative of Fe(0) indicates that a continuous shell of oxidised Fe was present. In the
case of P2 and P3, all techniques showed that oxidised forms of Fe were dominant both on the
surface and in the core of the particles. This characterisation study clearly demonstrates the
complementarity of the techniques employed, and shows the importance of a thorough
characterisation not only for laboratory experiments but also in the context of understanding the
performance and characteristics of commercial materials proposed for use in field applications.
5 Analytical challenges for characterizing nZVI in real groundwater samples
To date, most nZVI studies have focused on the characterisation of freshly synthesised
nanomaterials in simple matrices. However, the high reactivity of nZVI particles makes them highly
dynamic in complex environmental systems such as groundwater [148]. Understanding their
behaviour under environmental conditions is crucial for determining their long-term environmental
fate and performance once they are injected into contaminated groundwaters. Furthermore,
25
because of the large quantity of nZVI required for injection in remediation applications, risk
assessment of these materials needs to be conducted, and this requires the measurement of nZVI in
groundwaters.
At present, the direct measurement of engineered nanoparticles (ENPs) in the environment is still
limited by significant analytical challenges [149]. In fact, the different characterisation methods
described in this review can provide accurate information for “as-manufactured” nanoparticles in
simple matrices but they all present significant limitations when it comes to the detection and
quantification of ENPs in more complex samples [30].
Various analytical techniques and experimental methods have been tested to predict the behaviour
(i.e. aggregation/sedimentation/deposition, mobility and reactivity) of nZVI in groundwater. Some
examples are given in Table 8Error! Reference source not found.. One simple approach consists of
studying the individual or combined effects of different physical and chemical groundwater
components (e.g. effect of a single electrolyte, pH, organic matter concentration etc.) in order to
understand how these different factors can affect the mobility and reactivity of nZVI (e.g. [40, 150-
156]). These studies have found that increasing the ionic strength of the solution will increase both
particle aggregation (ref) and particle deposition onto soil grains (ref). However, in some of these
studies, the tested electrolyte concentrations were much higher than the ones found in
groundwater so the relevance of the data is questionable. The influence of humic acid concentration
was also investigated and was found to enhance the stability of nZVI by reducing its aggregation and
sedimentation (ref). In these studies, particle size was often measured by light scattering techniques
(i.e. LLS or DLS); however, as discussed in section 2.2., the presence of large aggregates in the
sample significantly affect the accuracy of the data. For this reason, Yin et al. (ref) only measured the
particle size after 30 minutes (i.e. only the size of the particles remaining in suspension was
measured). However, no information was provided on the sedimented particles (e.g. mass fraction).
Tiraferri et al. (ref) and Dong and Lo (ref) coupled DLS measurements with UV-Vis
26
spectrophotometer to investigate the sedimentation regime of the particles. These studies
demonstrated a two-phase aggregation/sedimentation regime with rapid sedimentation of large
aggregates followed by slow aggregation/sedimentation of the remaining particles in suspension.
Particle deposition was analysed by atomic absorption spectroscopy (AAS) which was used to
determine the concentration of iron in the effluent samples during column experiment studies (ref).
SEM/EDS were also employed to confirm the attachment of nZVI onto soil grains (ref). The oxidation
of nZVI over time (i.e. in different synthetic media) was also investigated since it was shown to also
affect the particle aggregation. Different techniques were tested to determine the oxidation state of
nZVI; which includes colorimeter (ref) and XRD coupled with TEM (ref).These studies confirmed the
development of corrosion products over time when nZVI is aged in different electrolyte solutions.
These data were well-correlated with particle size and particle sedimentation measurements, which
demonstrates the effectiveness and the need to develop multi-methods approach for nanoparticle
characterisation.
The results from these studies are generally easily reproducible and can help in gaining quantitative
data but they are only valid for the limited conditions examined in the experiments and cannot
necessarily be extrapolated to predict behaviour in natural systems. A more realistic approach
would be to investigate the behaviour of nZVI directly in natural groundwater samples. However,
further research in this area is required, partly because this type of investigation faces significant
analytical challenges.
Various field-scale studies of nZVI injection have been reported in the literature [3, 20, 157-162] but
due to a lack of appropriate analytical methods that can directly measure and detect nZVI on site,
most field studies have relied on indirect methods to quantify nZVI transport and reactivity. For
instance, both a decrease in ORP and a change in solution pH are widely reported upon nZVI
injection, and this is seen as evidence of the presence of nZVI and its mobility. However, a recent
study [163] showed that the interpretation from ORP measurements is quite complex as the
27
response of ORP electrodes to nZVI suspensions is not linearly correlated to nZVI concentration. For
instance, at low nZVI concentration (< 50 mg/L), the measured ORP likely represents a mixed
potential including the contributions from nZVI, dissolved Fe2+ and H2. ORP changes have also been
reported as an indicator of nZVI reactivity. Elliot and Zhang [3] reported a good correlation between
TCE degradation and ORP reduction at the closest monitoring well from the injection point.
However, this correlation was less obvious at monitoring wells located further away from the
injection point, where a lag period of one to several days was observed between the ORP reduction
and TCE decline. To circumvent the limitations of individual methods, Johnson et al. [162] utilised a
number of complimentary techniques to ensure that nZVI transport and reactivity were adequately
characterised. They developed a spectrophotometric method combining visual inspection (i.e.
change in colour), UV-vis absorbance measurements and the use of a tracer to directly quantify the
transport of nZVI as well as to detect any flow changes during the injection. They concluded that the
use of indirect indicators such as ORP, DO or pH is only relevant when they are used to supplement
direct characterisation methods.
Table 8
28
6 Conclusions
A thorough understanding of nZVI remediation potential, transport and fate in the environment can
only be achieved by ensuring that experimental results are always reported in conjunction with
appropriate and detailed nZVI characterisation data. This requirement is not limited to experimental
and laboratory work but extends to pilot and field scale remediation efforts. A large number of
analytical techniques can be employed to interrogate the physico-chemical characteristics of these
materials. To some extent the choice of the combination of techniques will depend on availability
but should cover key characteristics. Taking this into consideration, DLS for sizing, SEM for
morphology and ICP-MS for elemental purity are most likely available at the majority of modern
laboratories. Bulk mineralogical composition and surface chemistry analysis require costly
instruments that may not be readily available even though access to XRD facilities is often possible.
In any case, but care must be taken to handle nZVI appropriately to prevent oxidation and sample
transformation during preparation and analysis. The protocols to ensure preservation of the nZVI
materials will depend on the analytical technique considered and may vary from sealing the DLS vials
prior to removing the samples from an anaerobic chamber to ensuring that transfer into
spectroscopic instruments occurs through the use of appropriate transfer chambers.
Another issue to consider is that while for other nanoparticles certified reference materials are
available, this is not the case for nZVI. In the short term, and as a minimum, standard reference
materials already available for other classes of nanoparticles (such as Au nanoparticles) should be
used for quality control but ultimately the availability of nZVI certified reference materials is
required in order to confidently compare results from different laboratories.
While the techniques listed above, especially when used in combination, can provide a thorough
characterisation of nZVI materials, the detection, quantification and characterisation of nZVI and
nZVI-derived materials in the environment continue to pose considerable challenges that should be
the focus of future research efforts.
29
As most of the existing analytical techniques are mainly applicable for to the characterisation of
pristine or “as-manufactured” nanoparticles, there is a need to develop standard protocols for the
characterisation of nZVI in different environmental media with detailed procedure on sample
preparation, instrumentation, key measurement parameters as well as data analysis. This has been
already implemented for other nanoparticles such as carbon nanotubes [164, 165]. These methods
will also need to be validated through interlaboratory comparisons and then adopted by the
nanoscience community. This will facilitate data comparison between different laboratories.
30
Reference
1. R.A. Crane and T.B. Scott, Nanoscale zero-valent iron: Future prospects for an emerging water treatment technology, J. Hazard. Mater. 211-212 (2012) 112-125.
2. C.B. Wang and W.X. Zhang, Synthesizing nanoscale iron particles for rapid and complete dechlorination of TCE and PCBs, Environ. Sci. Technol. 31 (1997) 2154-2156.
3. D.W. Elliott and W.X. Zhang, Field assessment of nanoscale bimetallic particles for groundwater treatment, Environ. Sci. Technol. 35 (2001) 4922-4926.
4. W.X. Zhang, Nanoscale iron particles for environmental remediation: An overview, J. Nanopart. Res. 5 (2003) 323-332.
5. X.Q. Li, D.G. Brown, and W.X. Zhang, Stabilization of biosolids with nanoscale zero-valent iron (nZVI), J. Nanopart. Res. 9 (2007) 233-243.
6. H. Liu, T. Chen, X. Zou, Q. Xie, C. Qing, D. Chen, and R.L. Frost, Removal of phosphorus using NZVI derived from reducing natural goethite, Chem. Eng. J. 234 (2013) 80-87.
7. Z. Wen, Y. Zhang, and C. Dai, Removal of phosphate from aqueous solution using nanoscale zerovalent iron (nZVI), Colloids Surf., A 457 (2014) 433-440.
8. W.J. Epolito, H. Yang, L.A. Bottomley, and S.G. Pavlostathis, Kinetics of zero-valent iron reductive transformation of the anthraquinone dye Reactive Blue 4, J. Hazard. Mater. 160 (2008) 594-600.
9. J. Fan, Y. Guo, J. Wang, and M. Fan, Rapid decolorization of azo dye methyl orange in aqueous solution by nanoscale zerovalent iron particles, J. Hazard. Mater. 166 (2009) 904-910.
10. B. Ma, W. Yu, W.A. Jefferson, H. Liu, and J. Qu, Modification of ultrafiltration membrane with nanoscale zerovalent iron layers for humic acid fouling reduction, Water Res. 71 (2015) 140-149.
11. J.G. Darab, A.B. Amonette, D.S. Burke, R.D. Orr, S.M. Ponder, B. Schrick, T.E. Mallouk, W.W. Lukens, D.L. Caulder, and D.K. Shuh, Removal of pertechnetate from simulated nuclear waste streams using supported zerovalent iron, Chem. Mater. 19 (2007) 5703-5713.
12. G. Naja, A. Halasz, S. Thiboutot, G. Ampleman, and J. Hawari, Degradation of hexahydro-1, 3, 5-trinitro-1, 3, 5-triazine (RDX) using zerovalent iron nanoparticles, Environ. Sci. Technol. 42 (2008) 4364-4370.
13. G. Kim, W. Jeong, and S. Choe, Dechlorination of atrazine using zero-valent iron (Fe0) under neutral pH conditions, J. Hazard. Mater. 155 (2008) 502-506.
14. J.T. Nurmi, P.G. Tratnyek, V. Sarathy, D.R. Baer, J.E. Amonette, K. Pecher, C. Wang, J.C. Linehan, D.W. Matson, R.L. Penn, and M.D. Driessen, Characterization and properties of metallic iron nanoparticles: Spectroscopy, electrochemistry, and kinetics, Environ. Sci. Technol. 39 (2005) 1221-1230.
15. Y. Liu, H. Choi, D. Dionysiou, and G.V. Lowry, Trichloroethene hydrodechlorination in water by highly disordered monometallic nanoiron, Chem. Mater. 17 (2005) 5315-5322.
16. X.Q. Li, D.W. Elliott, and W.X. Zhang, Zero-valent iron nanoparticles for abatement of environmental pollutants: Materials and engineering aspects, Crit. Rev. Solid State Mater. Sci. 31 (2006) 111-122.
17. A.B. Cundy, L. Hopkinson, and R.L.D. Whitby, Use of iron-based technologies in contaminated land and groundwater remediation: A review, Sci. Total Environ. 400 (2008) 42-51.
18. B. Geng, Z. Jin, T. Li, and X. Qi, Preparation of chitosan-stabilized Fe0 nanoparticles for removal of hexavalent chromium in water, Sci. Total Environ. 407 (2009) 4994-5000.
19. B. Schrick, B.W. Hydutsky, J.L. Blough, and T.E. Mallouk, Delivery vehicles for zerovalent metal nanoparticles in soil and groundwater, Chem. Mater. 16 (2004) 2187-2193.
31
20. J. Quinn, C. Geiger, C. Clausen, K. Brooks, C. Coon, S. O'Hara, T. Krug, D. Major, W.S. Yoon, A. Gavaskar, and T. Holdsworth, Field demonstration of DNAPL dehalogenation using emulsified zero-valent iron, Environ. Sci. Technol. 39 (2005) 1309-1318.
21. F. He and D. Zhao, Manipulating the size and dispersibility of zerovalent iron nanoparticles by use of carboxymethyl cellulose stabilizers, Environ. Sci. Technol. 41 (2007) 6216-6221.
22. N. Saleh, K. Sirk, Y. Liu, T. Phenrat, B. Dufour, K. Matyjaszewski, R.D. Tilton, and G.V. Lowry, Surface modifications enhance nanoiron transport and NAPL targeting in saturated porous media, Environ. Eng. Sci. 24 (2007) 45-57.
23. M. Elimelech, X. Jia, J. Gregory, and R.A. Williams, in Particle deposition and aggregation: measurement, modelling and simulation 1998, Butterworth-Heinemann Woburn, Massachusetts p. 440.
24. S.R. Kanel, R.R. Goswami, T.P. Clement, M.O. Barnett, and D. Zhao, Two dimensional transport characteristics of surface stabilized zero-valent iron nanoparticles in porous media, Environ. Sci. Technol. 42 (2008) 896-900.
25. T.B. Scott, Inorganic nanoparticles for remediation in Inorganic Nanoparticles: Synthesis, Applications, and Perspectives C. Altavilla and E. Ciliberto, Editors. 2011, CRC Press Boca Raton, FL p. 393-441
26. T. Phenrat, N. Saleh, K. Sirk, R.D. Tilton, and G.V. Lowry, Aggregation and sedimentation of aqueous nanoscale zerovalent iron dispersions, Environ. Sci. Technol. 41 (2007) 284-290.
27. J. Theron, J. Walker, and T. Cloete, Nanotechnology and water treatment: applications and emerging opportunities, Crit. Rev. Microbiol. 34 (2008) 43-69.
28. Y.P. Sun, X.Q. Li, J. Cao, W.X. Zhang, and H.P. Wang, Characterization of zero-valent iron nanoparticles, Adv. Colloid Interface Sci. 120 (2006) 47-56.
29. L. Li, M. Fan, R.C. Brown, J. Van Leeuwen, J. Wang, W. Wang, Y. Song, and P. Zhang, Synthesis, properties, and environmental applications of nanoscale iron-based materials: A review, Crit. Rev. Env. Sci. Technol. 36 (2006) 405-431.
30. F. von der Kammer, P.L. Ferguson, P.A. Holden, A. Masion, K.R. Rogers, S.J. Klaine, A.A. Koelmans, N. Horne, and J.M. Unrine, Analysis of engineered nanomaterials in complex matrices (environment and biota): General considerations and conceptual case studies, Environ. Toxicol. Chem. 31 (2012) 32-49.
31. D.R. Baer, D.J. Gaspar, P. Nachimuthu, S.D. Techane, and D.G. Castner, Application of surface chemical analysis tools for characterization of nanoparticles, Anal Bioanal Chem 396 (2010) 983-1002.
32. M. Hassellöv, J.W. Readman, J.F. Ranville, and K. Tiede, Nanoparticle analysis and characterization methodologies in environmental risk assessment of engineered nanoparticles, Ecotoxicol. 17 (2008) 344-361.
33. P. Christian, F. Von der Kammer, M. Baalousha, and T. Hofmann, Nanoparticles: structure, properties, preparation and behaviour in environmental media, Ecotoxicol. 17 (2008) 326-343.
34. L. Signorini, L. Pasquini, L. Savini, R. Carboni, F. Boscherini, E. Bonetti, A. Giglia, M. Pedio, N. Mahne, and S. Nannarone, Size-dependent oxidation in iron/iron oxide core-shell nanoparticles, Phys. Rev. B 68 (2003) 195423.
35. H.S. Kim, J.Y. Ahn, K.Y. Hwang, I.K. Kim, and I. Hwang, Atmospherically stable nanoscale zero-valent iron particles formed under controlled air contact: characteristics and reactivity, Environ. Sci. Technol. 44 (2010) 1760-1766.
36. N. Saleh, T. Phenrat, K. Sirk, B. Dufour, J. Ok, T. Sarbu, K. Matyjaszewski, R.D. Tilton, and G.V. Lowry, Adsorbed triblock copolymers deliver reactive iron nanoparticles to the oil/water interface, Nano Lett. 5 (2005) 2489-2494.
37. S.R. Kanel, D. Nepal, B. Manning, and H. Choi, Transport of surface-modified iron nanoparticle in porous media and application to arsenic (III) remediation, J. Nanopart. Res. 9 (2007) 725-735.
32
38. W. Yan, A.A. Herzing, C.J. Kiely, and W.X. Zhang, Nanoscale zero-valent iron (nZVI): Aspects of the core-shell structure and reactions with inorganic species in water, J. Contam. Hydrol. 118 (2010) 96-104.
39. A.B.M. Giasuddin, S.R. Kanel, and H. Choi, Adsorption of humic acid onto nanoscale zerovalent iron and its effect on arsenic removal, Environ. Sci. Technol. 41 (2007) 2022-2027.
40. A. Tiraferri, K.L. Chen, R. Sethi, and M. Elimelech, Reduced aggregation and sedimentation of zero-valent iron nanoparticles in the presence of guar gum, J. Colloid Interface Sci. 324 (2008) 71-79.
41. Y.H. Lin, H.H. Tseng, M.Y. Wey, and M.D. Lin, Characteristics of two types of stabilized nano zero-valent iron and transport in porous media, Sci. Total Environ. 408 (2010) 2260-2267.
42. Y.H. Hwang, D.G. Kim, and H.S. Shin, Effects of synthesis conditions on the characteristics and reactivity of nano scale zero valent iron, Appl. Catal., B 105 (2011) 144-150.
43. F. He, D. Zhao, J. Liu, and C.B. Roberts, Stabilization of Fe - Pd nanoparticles with sodium carboxymethyl cellulose for enhanced transport and dechlorination of trichloroethylene in soil and groundwater, Ind. Eng. Chem. Res. 46 (2007) 29-34.
44. C.M. Cirtiu, T. Raychoudhury, S. Ghoshal, and A. Moores, Systematic comparison of the size, surface characteristics and colloidal stability of zero valent iron nanoparticles pre- and post-grafted with common polymers, Colloids Surf., A 390 (2011) 95-104.
45. J.R. Lead and K.J. Wilkinson, Aquatic colloids and nanoparticles: current knowledge and future trends, Environ. Chem. 3 (2006) 159-171.
46. R.F. Domingos, M.A. Baalousha, Y. Ju-Nam, M.M. Reid, N. Tufenkji, J.R. Lead, G.G. Leppard, and K.J. Wilkinson, Characterizing manufactured nanoparticles in the environment: multimethod determination of particle sizes, Environ Sci Technol 43 (2009) 7277-7284.
47. A. Jillavenkatesa, S.J. Dapkunas, and L.-S.H. Lum, Special Publication 960-1: Partice Size Characterisation in NIST Recommended Practice Guide (2001) National Institute of Standards and Technology.
48. C. Singh, S. Friedrichs, M. Levin, R. Birkedal, K.A. Jensen, G. Pojana, W. Wohlleben, S. Schulte, K. Wiench, T. Turney, O. Koulaeva, D. Marshall, K. Hund-Rinke, W. Kördel, E. Van Doren, P.-J. De Temmerman, M. Abi Daoud Francisco, J. Mast, N. Gibson, R. Koeber, T. Linsinger, and C.L. Klein, Zinc Oxide NM-110, NM-111, NM-112, NM-113 Characterisation and Test Item Preparation in NM-Series of Representative Manufactured Nanomaterials (2011) JRS Institute for Reference Materials and Measurements.
49. C.L. Klein, Comero, B. Stahlmecke, J. Romazanov, T.A.J. Kuhlbusch, E. Van Doren, P.-J. De Temmerman, J. Mast, P. Wick, H.F. Krug, G. Locoro, K. Hund-Rinke, W. Kördel, S. Friedrichs, G. Maier, J. Werner, T. Linsinger, and B.M. Gawlik, NM-300 Silver Characterisation, Stability, Homogeneity in NM-Series of Representative Manufactured Nanomaterials (2011) JRS Institute for Health and Consumer Protection.
50. W.S. Rasband, ImageJ, 1997-2012, U.S. National Institutes of Health: Bethesda, Maryland, USA.
51. R. Yuvakkumar, V. Elango, V. Rajendran, and N. Kannan, Preparation and characterization of zero valent Iron nanoparticles, Dig. J. Nano. Biost. 6 (2011) 1771-1776.
52. L.N. Shi, Y.M. Lin, X. Zhang, and Z.L. Chen, Synthesis, characterization and kinetics of bentonite supported nZVI for the removal of Cr(VI) from aqueous solution, Chem. Eng. J. 171 (2011) 612-617.
53. S.R. Kanel, B. Manning, L. Charlet, and H. Choi, Removal of arsenic (III) from groundwater by nanoscale zero-valent iron, Environ. Sci. Technol. 39 (2005) 1291-1298.
54. H.C. Choi, A.B.M. Giasuddin, and S.R. Kanel, Method of synthesizing air-stable zero-valent iron nanoparticles at room temperature and applications, 2007, Google Patents.
55. J. WooáLee and S. BináKim, Enhanced Cr(VI) removal using iron nanoparticle decorated graphene, Nanoscale 3 (2011) 3583-3585.
33
56. C.M. Wang, D.R. Baer, J.E. Amonette, M.H. Engelhard, Y. Qiang, and J. Antony, Morphology and oxide shell structure of iron nanoparticles grown by sputter-gas-aggregation, Nanotechnol. 18 (2007) 255603.
57. C.M. Wang, D.R. Baer, J.E. Amonette, M.H. Engelhard, J. Antony, and Y. Qiang, Electron beam-induced thickening of the protective oxide layer around Fe nanoparticles, Ultramicroscopy 108 (2007) 43-51.
58. H.G. Cha, Y.H. Kim, C.W. Kim, and Y.S. Kang, Preparation of aqueous dispersion of colloidal α-Fe nanoparticle by phase transfer, Sens. Actuators, B 126 (2007) 221-225.
59. J.T. Nurmi, P.G. Tratnyek, V. Sarathy, D.R. Baer, J.E. Amonette, K. Pecher, C. Wang, J.C. Linehan, D.W. Matson, R.L. Penn, and M.D. Driessen, Characterization and Properties of Metallic Iron Nanoparticles: Spectroscopy, Electrochemistry, and Kinetics, Environ Sci Technol 39 (2004) 1221-1230.
60. C. Wang, D.R. Baer, J.E. Amonette, M.H. Engelhard, J. Antony, and Y. Qiang, Morphology and Electronic Structure of the Oxide Shell on the Surface of Iron Nanoparticles, J Am Chem Soc 131 (2009) 8824-8832.
61. Q. Wang, S. Lee, and H. Choi, Aging study on the structure of Fe0-nanoparticles: stabilization, characterization, and reactivity, The J. Phy. Chem., C 114 (2010) 2027-2033.
62. J.E. Martin, A.A. Herzing, W. Yan, X.Q. Li, B.E. Koel, C.J. Kiely, and W.X. Zhang, Determination of the oxide layer thickness in core-shell zerovalent iron nanoparticles, Langmuir 24 (2008) 4329-4334.
63. W. Yan, A.A. Herzing, X.Q. Li, C.J. Kiely, and W.X. Zhang, Structural evolution of Pd-doped nanoscale zero-valent iron (nZVI) in aqueous media and implications for particle aging and reactivity, Environ. Sci. Technol. 44 (2010) 4288-4294.
64. W. Yan, R. Vasic, A.I. Frenkel, and B.E. Koel, Intraparticle reduction of arsenite (As (III)) by nanoscale zerovalent iron (nZVI) investigated with in situ X-ray absorption spectroscopy, Environ. Sci. Technol. 46 (2012) 7018-7026.
65. L. Ling and W.X. Zhang, Reactions of nanoscale zero-valent iron with Ni (II): three-dimensional tomography of the “hollow out” effect in a single nanoparticle, Environ. Sci. Technol. Lett. 1 (2014) 209-213.
66. A.H. Latham and M.E. Williams, Transmission Electron Microscope-Induced Structural Evolution in Amorphous Fe, Co, and Ni Oxide Nanoparticles, Langmuir 24 (2008) 14195-14202.
67. R.D. Glover, J.M. Miller, and J.E. Hutchison, Generation of Metal Nanoparticles from Silver and Copper Objects: Nanoparticle Dynamics on Surfaces and Potential Sources of Nanoparticles in the Environment, ACS Nano 5 (2011) 8950-8957.
68. S.R. Kanel, J.M. Greneche, and H. Choi, Arsenic (V) removal from groundwater using nano scale zero-valent iron as a colloidal reactive barrier material, Environ. Sci. Technol. 40 (2006) 2045-2050.
69. J. Su, S. Lin, Z. Chen, M. Megharaj, and R. Naidu, Dechlorination of p-chlorophenol from aqueous solution using bentonite supported Fe/Pd nanoparticles: Synthesis, characterization and kinetics, Desalination 280 (2011) 167-173.
70. Ç. Üzüm, T. Shahwan, A.E. Eroğlu, K.R. Hallam, T.B. Scott, and I. Lieberwirth, Synthesis and characterization of kaolinite-supported zero-valent iron nanoparticles and their application for the removal of aqueous Cu 2+ and Co 2+ ions, Appl. Clay Sci. 43 (2009) 172-181.
71. X. Wu, Q. Yang, D. Xu, Y. Zhong, K. Luo, X. Li, H. Chen, and G. Zeng, Simultaneous adsorption/reduction of bromate by nanoscale zerovalent iron supported on modified activated carbon, Ind. Eng. Chem. Res. 52 (2013) 12574-12581.
72. A.N. Bezbaruah, S. Krajangpan, B.J. Chisholm, E. Khan, and J.J.E. Bermudez, Entrapment of iron nanoparticles in calcium alginate beads for groundwater remediation applications, J. Hazard. Mater. 166 (2009) 1339-1343.
34
73. S.C.G. Kiruba Daniel, G. Vinothini, N. Subramanian, K. Nehru, and M. Sivakumar, Biosynthesis of Cu, ZVI, and Ag nanoparticles using Dodonaea viscosa extract for antibacterial activity against human pathogens, J. Nanopart. Res. 15 (2012) 1-10.
74. Y.-T. Lin, C.-H. Weng, and F.-Y. Chen, Effective removal of AB24 dye by nano/micro-size zero-valent iron, Sep. Purif. Technol. 64 (2008) 26-30.
75. S.R. Qiu, H.F. Lai, M.J. Roberson, M.L. Hunt, C. Amrhein, L.C. Giancarlo, G.W. Flynn, and J.A. Yarmoff, Removal of Contaminants from Aqueous Solution by Reaction with Iron Surfaces, Langmuir 16 (2000) 2230-2236.
76. A.R. Badireddy, M.R. Wiesner, and J. Liu, Detection, characterization, and abundance of engineered nanoparticles in complex waters by hyperspectral imagery with enhanced darkfield microscopy, Environ. Sci. Technol. 46 (2012) 10081-10088.
77. M.G. Gustafsson, Surpassing the lateral resolution limit by a factor of two using structured illumination microscopy, J. Microsc. 198 (2000) 82-87.
78. D. Baddeley, C. Batram, Y. Weiland, C. Cremer, and U.J. Birk, Nanostructure analysis using spatially modulated illumination microscopy, Nat. Protoc. 2 (2007) 2640-2646.
79. M.J. Rust, M. Bates, and X. Zhuang, Sub-diffraction-limit imaging by stochastic optical reconstruction microscopy (STORM), Nat. Methods 3 (2006) 793-796.
80. B. Ward, J.A. Notte, and N. Economou, Helium ion microscope: A new tool for nanoscale microscopy and metrology, J. Vac. Sci. Technol., B 24 (2006) 2871-2874.
81. M. Kaur, J.S. McCloy, W. Jiang, Q. Yao, and Y. Qiang, Size dependence of inter-and intracluster interactions in core–shell iron–iron oxide nanoclusters, The J. Phy. Chem., C 116 (2012) 12875-12885.
82. P. Schurtenberger and M.E. Newman, Characterization of biological and environmental particles using static and dynamic light scattering, Environ. Part. 2 (1993) 37-115.
83. M. Farré, J. Sanchís, and D. Barceló, Analysis and assessment of the occurrence, the fate and the behavior of nanomaterials in the environment, TrAC, Trends Anal. Chem. 30 (2011) 517-527.
84. A. Ledin, S. Karlsson, A. Düker, and B. Allard, Measurements< i> in situ</i> of concentration and size distribution of colloidal matter in deep groundwaters by photon correlation spectroscopy, Water Res. 28 (1994) 1539-1545.
85. L. Honetschlagerova, P. Janouskovcova, and Z. Soffer, NANOSCALE ZERO VALENT IRON COATING FOR SUBSURFACE APPLICATION, in Nanocon 20122012: Brno, Czech Republic.
86. T. Phenrat, H.J. Kim, F. Fagerlund, T. Illangasekare, R.D. Tilton, and G.V. Lowry, Particle size distribution, concentration, and magnetic attraction affect transport of polymer-modified Fe0 nanoparticles in sand columns, Environ. Sci. Technol. 43 (2009) 5079-5085.
87. Y.H. Shih, C.Y. Hsu, and Y.F. Su, Reduction of hexachlorobenzene by nanoscale zero-valent iron: kinetics, pH effect, and degradation mechanism, Sep. Purif. Technol. 76 (2011) 268-274.
88. H.J. Kim, T. Phenrat, R.D. Tilton, and G.V. Lowry, Effect of kaolinite, silica fines and pH on transport of polymer-modified zero valent iron nano-particles in heterogeneous porous media, J. Colloid Interface Sci. 370 (2012) 1-10.
89. J. Fatisson, S. Ghoshal, and N. Tufenkji, Deposition of carboxymethylcellulose-coated zero-valent iron nanoparticles onto silica: Roles of solution chemistry and organic molecules, Langmuir 26 (2010) 12832-12840.
90. C.M. Kocur, D.M. O'Carroll, and B.E. Sleep, Impact of nZVI stability on mobility in porous media, J. Contam. Hydrol. (2012)
91. M. Filella, J. Zhang, M.E. Newman, and J. Buffle, Analytical applications of photon correlation spectroscopy for size distribution measurements of natural colloidal suspensions: capabilities and limitations, Colloids Surf., A 120 (1997) 27-46.
92. P.C. Hiemenz and R. Rajagopalan, Principles of Colloid and Surface Chemistry, revised and expanded. Vol. 14. 1997: CRC Press.
35
93. S.M. Ponder, J.G. Darab, and T.E. Mallouk, Remediation of Cr(VI) and Pb(II) aqueous solutions using supported, nanoscale zero-valent iron, Environ. Sci. Technol. 34 (2000) 2564-2569.
94. H. Weinberg, A. Galyean, and M. Leopold, Evaluating engineered nanoparticles in natural waters, TrAC, Trends Anal. Chem. 30 (2011) 72-83.
95. C.W. Isaacson and D. Bouchard, Asymmetric flow field flow fractionation of aqueous C60 nanoparticles with size determination by dynamic light scattering and quantification by liquid chromatography atmospheric pressure photo-ionization mass spectrometry, J. Chromatogr. A 1217 (2010) 1506-1512.
96. L.H. Hanus and H.J. Ploehn, Conversion of intensity-averaged photon correlation spectroscopy measurements to number-averaged particle size distributions. 1. Theoretical development, Langmuir 15 (1999) 3091-3100.
97. R. Finsy, Particle sizing by quasi-elastic light scattering, Adv. Colloid Interface Sci. 52 (1994) 79-143.
98. D. O’Carroll, B. Sleep, M. Krol, H. Boparai, and C. Kocur, Nanoscale zero valent iron and bimetallic particles for contaminated site remediation, AdWR (2012)
99. K.D. Grieger, A. Fjordboge, N.B. Hartmann, E. Eriksson, P.L. Bjerg, and A. Baun, Environmental benefits and risks of zero-valent iron nanoparticles (nZVI) for in situ remediation: Risk mitigation or trade-off?, J. Contam. Hydrol. 118 (2010) 165-183.
100. K.S. Lin, N.B. Chang, and T.D. Chuang, Fine structure characterization of zero-valent iron nanoparticles for decontamination of nitrites and nitrates in wastewater and groundwater, Sci. Technol. Adv. Mater. 9 (2008) 025015.
101. Y. Xi, M. Mallavarapu, and R. Naidu, Reduction and adsorption of Pb2+ in aqueous solution by nano-zero-valent iron—a SEM, TEM and XPS study, Mater. Res. Bull. 45 (2010) 1361-1367.
102. M. Dickinson and T.B. Scott, The application of zero-valent iron nanoparticles for the remediation of a uranium-contaminated waste effluent, J. Hazard. Mater. 178 (2010) 171-179.
103. Q. Wang, S. Snyder, J. Kim, and H. Choi, Aqueous ethanol modified nanoscale zerovalent iron in bromate reduction: synthesis, characterization, and reactivity, Environ. Sci. Technol. 43 (2009) 3292-3299.
104. S. Li, W. Yan, and W.X. Zhang, Solvent-free production of nanoscale zero-valent iron (nZVI) with precision milling, Green Chem. 11 (2009) 1618-1626.
105. T. Zheng, J. Zhan, J. He, C. Day, Y. Lu, G.L. McPherson, G. Piringer, and V.T. John, Reactivity Characteristics of Nanoscale Zerovalent Iron−Silica Composites for Trichloroethylene Remediation, Environ Sci Technol 42 (2008) 4494-4499.
106. J.T. Nurmi, P.G. Tratnyek, V. Sarathy, D.R. Baer, J.E. Amonette, K. Pecher, C. Wang, J.C. Linehan, D.W. Matson, and R.L. Penn, Characterization and properties of metallic iron nanoparticles: spectroscopy, electrochemistry, and kinetics, Environmental Science & Technology 39 (2005) 1221-1230.
107. S.M. Ponder, J.G. Darab, J. Bucher, D. Caulder, I. Craig, L. Davis, N. Edelstein, W. Lukens, H. Nitsche, L. Rao, D.K. Shuh, and T.E. Mallouk, Surface Chemistry and Electrochemistry of Supported Zerovalent Iron Nanoparticles in the Remediation of Aqueous Metal Contaminants, Chem. Mater. 13 (2001) 479-486.
108. J. Leveneur, G.I. Waterhouse, J. Kennedy, J.B. Metson, and D.R. Mitchell, Nucleation and growth of Fe nanoparticles in SiO2: a TEM, XPS, and Fe L-edge XANES investigation, The J. Phy. Chem., C 115 (2011) 20978-20985.
109. B.C. Reinsch, B. Forsberg, R.L. Penn, C.S. Kim, and G.V. Lowry, Chemical Transformations during Aging of Zerovalent Iron Nanoparticles in the Presence of Common Groundwater Dissolved Constituents, Environ Sci Technol 44 (2010) 3455-3461.
36
110. W. Yan, A.A. Herzing, C.J. Kiely, and W. Zhang, Nanoscale zero-valent iron (nZVI): Aspects of the core-shell structure and reactions with inorganic species in water, J. Contam. Hydrol. 118 (2010) 96-104.
111. Y.P. Sun, X.Q. Li, W.X. Zhang, and H.P. Wang, A method for the preparation of stable dispersion of zero-valent iron nanoparticles, Colloids Surf., A 308 (2007) 60-66.
112. Y. Liu and B. Yan, Characterizing the surface chemistry of nanoparticles: an analogy to solid-phase synthesis samples, Comb. Chem. High Throughput Screening 14 (2011) 191-197.
113. Q. Wang, S. Kanel, H. Park, A. Ryu, and H. Choi, Controllable synthesis, characterization, and magnetic properties of nanoscale zerovalent iron with specific high Brunauer–Emmett–Teller surface area, J Nanopart Res 11 (2009) 749-755.
114. L.S. Wang and R.Y. Hong, Synthesis, Surface Modification and Characterisation of Nanoparticles, in Advances in Nanocomposites - Synthesis, Characterization and Industrial Applications, D.B. Reddy, Editor 2011.
115. B.E. Warren, X-ray Diffraction1969: Courier Corporation. 116. H.P. Klug and L.E. Alexander, X-ray diffraction procedures, (1954) 117. Z. Fang, J. Chen, X. Qiu, X. Qiu, W. Cheng, and L. Zhu, Effective removal of antibiotic
metronidazole from water by nanoscale zero-valent iron particles, Desalination 268 (2011) 60-67.
118. M.R. Jamei, M.R. Khosravi, and B. Anvaripour, A novel ultrasound assisted method in synthesis of NZVI particles, Ultrason. Sonochem. 21 (2014) 226-233.
119. A.R. Esfahani, A.F. Firouzi, G. Sayyad, and A. Kiasat, Transport and retention of polymer-stabilized zero-valent iron nanoparticles in saturated porous media: Effects of initial particle concentration and ionic strength, J. Ind. Eng. Chem. 20 (2013) 2671-2679.
120. D. Karabelli, C.a.r. Üzüm, T. Shahwan, A.E. Eroglu, T.B. Scott, K.R. Hallam, and I. Lieberwirth, Batch removal of aqueous Cu2+ ions using nanoparticles of zero-valent iron: a study of the capacity and mechanism of uptake, Ind. Eng. Chem. Res. 47 (2008) 4758-4764.
121. Y.C. Lee, C.W. Kim, J.Y. Lee, H.J. Shin, and J.W. Yang, Characterization of nanoscale zero valent iron modified by nonionic surfactant for trichloroethylene removal in the presence of humic acid: A research note, Desalin. Water Treat. 10 (2009) 33-38.
122. S.N. Zhu, G.H. Liu, Z. Ye, Q. Zhao, and Y. Xu, Reduction of dinitrotoluene sulfonates in TNT red water using nanoscale zerovalent iron particles, Environ. Sci. Pollut. Res. 19 (2012) 2372-2380.
123. C. He, J. Yang, L. Zhu, Q. Zhang, W. Liao, S. Liu, Y. Liao, M.A. Asi, and D. Shu, pH-dependent degradation of acid orange II by zero-valent iron in presence of oxygen, Sep. Purif. Technol. 117 (2013) 59-68.
124. H. Dong, X. Guan, and I.M. Lo, Fate of As (V)-treated nano zero-valent iron: determination of arsenic desorption potential under varying environmental conditions by phosphate extraction, Water Res. 46 (2012) 4071-4080.
125. Ç. Üzüm, T. Shahwan, A. Eroğlu, I. Lieberwirth, T. Scott, and K. Hallam, Application of zero-valent iron nanoparticles for the removal of aqueous Co2+ ions under various experimental conditions, Chem. Eng. J. 144 (2008) 213-220.
126. S. Machado, J.G. Pacheco, H.P.A. Nouws, J.T. Albergaria, and C. Delerue-Matos, Characterization of green zero-valent iron nanoparticles produced with tree leaf extracts, Sci. Total Environ. 533 (2015) 76-81.
127. E.C. Njagi, H. Huang, L. Stafford, H. Genuino, H.M. Galindo, J.B. Collins, G.E. Hoag, and S.L. Suib, Biosynthesis of iron and silver nanoparticles at room temperature using aqueous sorghum bran extracts, Langmuir 27 (2011) 264-271.
128. T. Shahwan, S. Abu Sirriah, M. Nairat, E. Boyaci, A.E. Eroĝlu, T.B. Scott, and K.R. Hallam, Green synthesis of iron nanoparticles and their application as a Fenton-like catalyst for the degradation of aqueous cationic and anionic dyes, Chem. Eng. J. 172 (2011) 258-266.
37
129. D.R. Baer, J.E. Amonette, M.H. Engelhard, D.J. Gaspar, A.S. Karakoti, S. Kuchibhatla, P. Nachimuthu, J.T. Nurmi, Y. Qiang, V. Sarathy, S. Seal, A. Sharma, P.G. Tratnyek, and C.M. Wang, Characterization challenges for nanomaterials, Surf. Interface Anal. 40 (2008) 529-537.
130. D.R. Baer and M.H. Engelhard, XPS analysis of nanostructured materials and biological surfaces, J. Electron. Spectrosc. Relat. Phenom. 178–179 (2010) 415-432.
131. I.M. Kempson, W.M. Skinner, and P. Kirkbride, Calcium distributions in human hair by ToF-SIMS, Biochim. Biophys. Acta-General Subjects 1624 (2003) 1-5.
132. S.R. Grano, M. Sollaart, W. Skinner, C.A. Prestidge, and J. Ralston, Surface modifications in the chalcopyrite-sulphite ion system. I. collectorless flotation, XPS and dissolution study, Int. J. Miner. Process. 50 (1997) 1-26.
133. S.R. Grano, H. Cnossen, W. Skinner, C.A. Prestidge, and J. Ralston, Surface modifications in the chalcopyrite-sulphite ion system, II. Dithiophosphate collector adsorption study, Int. J. Miner. Process. 50 (1997) 27-45.
134. A.S. Karakoti, L.L. Hench, and S. Seal, The potential toxicity of nanomaterials—The role of surfaces, JOM 58 (2006) 77-82.
135. N.H. Turner, B.I. Dunlap, and R.J. Colton, Surface analysis: x-ray photoelectron spectroscopy, Auger electron spectroscopy and secondary ion mass spectrometry, Anal. Chem. 56 (1984) 373R-416R.
136. D.R. Baer, P.G. Tratnyek, Y. Qiang, J.E. Amonette, J. Linehan, V. Sarathy, J.T. Nurmi, C. Wang, and J. Anthony, Synthesis, Characterisation, and properties of zero-valent iron nanoparticles, in Environmental applications of nanomaterials; synthesis, sorbents and sensors, G.E. Fryxell and G. Cao, Editors. 2012, Imperial College Press: London.
137. A.M. Venezia, X-ray photoelectron spectroscopy (XPS) for catalysts characterization, Catal. Today 77 (2003) 359-370.
138. M. Grafe, E. Donner, R.N. Collins, and E. Lombi, Speciation of metal(loid)s in environmental samples by X-ray absorption spectroscopy: A critical review, Anal. Chim. Acta 822 (2014) 22.
139. J. Prietzel, J. Thieme, K. Eusterhues, and D. Eichert, Iron speciation in soils and soil aggregates by synchrotron-based X-ray microspectroscopy (XANES,μ-XANES), Eur. J. Soil Sci. 58 (2007) 1027-1041.
140. J. Feldmann, P. Salaün, and E. Lombi, Critical review perspective: elemental speciation analysis methods in environmental chemistry–moving towards methodological integration, Environ. Chem. 6 (2009) 275-289.
141. E. Lombi and J. Susini, Synchrotron-based techniques for plant and soil science: opportunities, challenges and future perspectives, Plant Soil 320 (2009) 1-35.
142. T. Phenrat, N. Saleh, K. Sirk, R.D. Tilton, and G.V. Lowry, Aggregation and sedimentation of aqueous nanoscale zerovalent iron dispersions, Environ. Sci. Technol. 41 (2007) 284-290.
143. L.F. Greenlee, J.D. Torrey, R.L. Amaro, and J.M. Shaw, Kinetics of Zero Valent Iron Nanoparticle Oxidation in Oxygenated Water, Environ Sci Technol 46 (2012) 12913-12920.
144. G.C. Allen, M.T. Curtis, A.J. Hooper, and P.M. Tucker, X-Ray photoelectron spectroscopy of iron-oxygen systems, J. Chem. Soc., Dalton Trans. 0 (1974) 1525-1530.
145. J.N. Fiedor, W.D. Bostick, R.J. Jarabek, and J. Farrell, Understanding the Mechanism of Uranium Removal from Groundwater by Zero-Valent Iron Using X-ray Photoelectron Spectroscopy, Environ Sci Technol 32 (1998) 1466-1473.
146. B. Ravel and M. Newville, ATHENA, ARTEMIS, HEPHAESTUS: data analysis for x-ray absorption spectroscopy using IFEFFIT., J. Synchrotron Radiat. 12 (2005) 537-541.
147. T. Ressler, WinXAS: a program for X-ray absorption spectroscopy data analysis under MS-Windows, J. Synchrotron Radiat. 5 (1998) 118-122.
148. G.V. Lowry, K.B. Gregory, S.C. Apte, and J.R. Lead, Transformations of nanomaterials in the environment, Environ Sci Technol 46 (2012) 6893-6899.
38
149. F. Gottschalk, T. Sonderer, R.W. Scholz, and B. Nowack, Possibilities and limitations of modeling environmental exposure to engineered nanomaterials by probabilistic material flow analysis, Environ. Toxicol. Chem. 29 (2010) 1036-1048.
150. H. Dong and I. Lo, Influence of humic acid on the colloidal stability of surface-modified nano zero-valent iron, Water Res. 47 (2013) 419-427.
151. A.R. Esfahani, A.F. Firouzi, G. Sayyad, and A. Kiasat, Transport and retention of polymer-stabilized zero-valent iron nanoparticles in saturated porous media: Effects of initial particle concentration and ionic strength, J. Ind. Eng. Chem. (2013)
152. R.L. Johnson, G.O.B. Johnson, J.T. Nurmi, and P.G. Tratnyek, Natural organic matter enhanced mobility of nano zerovalent iron, Environ. Sci. Technol. 43 (2009) 5455-5460.
153. T. Raychoudhury, N. Tufenkji, and S. Ghoshal, Aggregation and deposition kinetics of carboxymethyl cellulose-modified zero-valent iron nanoparticles in porous media, Water Res. 46 (2012) 1735-1744.
154. Y. Xie and D.M. Cwiertny, Influence of anionic cosolutes and pH on nanoscale zerovalent iron longevity: time scales and mechanisms of reactivity loss toward 1, 1, 1, 2-tetrachloroethane and Cr (VI), Environ. Sci. Technol. 46 (2012) 8365-8373.
155. K. Yin, I. Lo, H. Dong, P. Rao, and M.S. Mak, Lab-scale simulation of the fate and transport of nano zero-valent iron in subsurface environments: Aggregation, sedimentation, and contaminant desorption, J. Hazard. Mater. 227 (2012) 118-125.
156. A.S. Adeleye, A.A. Keller, R.J. Miller, and H.S. Lenihan, Persistence of commercial nanoscaled zero-valent iron (nZVI) and by-products, J. Nanopart. Res. 15 (2013)
157. K.W. Henn and D.W. Waddill, Utilization of nanoscale zero-valent iron for source remediation: A case study, Rem. J. 16 (2006) 57-77.
158. Y.T. Wei, S.C. Wu, C.M. Chou, C.H. Che, S.M. Tsai, and H.L. Lien, Influence of nanoscale zero-valent iron on geochemical properties of groundwater and vinyl chloride degradation: a field case study, Water Res. 44 (2010) 131-140.
159. F. He, D. Zhao, and C. Paul, Field assessment of carboxymethyl cellulose stabilized iron nanoparticles for in situ destruction of chlorinated solvents in source zones, Water Res. 44 (2010) 2360-2370.
160. P. Bennett, F. He, D. Zhao, B. Aiken, and L. Feldman, In situ testing of metallic iron nanoparticle mobility and reactivity in a shallow granular aquifer, J. Contam. Hydrol. 116 (2010) 35-46.
161. C.M. Kocur, A.I. Chowdhury, N. Sakulchaicharoen, H.K. Boparai, K.P. Weber, P. Sharma, M.M. Krol, L.M. Austrins, C. Peace, and B.E. Sleep, Characterization of nZVI mobility in a field scale test, Environ. Sci. Technol. (2014)
162. R.L. Johnson, J.T. Nurmi, G.S. O’Brien Johnson, D. Fan, R.L. O’Brien Johnson, Z. Shi, A.J. Salter-Blanc, P.G. Tratnyek, and G.V. Lowry, Field-scale transport and transformation of carboxymethylcellulose-stabilized nano zero-valent iron, Environ. Sci. Technol. 47 (2013) 1573-1580.
163. Z. Shi, J.T. Nurmi, and P.G. Tratnyek, Effects of nano zero-valent iron on oxidation− reduction potential, Environ. Sci. Technol. 45 (2011) 1586-1592.
164. S. Arepalli, P. Nikolaev, O. Gorelik, V.G. Hadjiev, W. Holmes, B. Files, and L. Yowell, Protocol for the characterization of single-wall carbon nanotube material quality, Carbon 42 (2004) 1783-1791.
165. J. Decker, A.H. Walker, K. Bosnick, C. Clifford, L. Dai, J. Fagan, S. Hooker, Z. Jakubek, C. Kingston, and J. Makar, Sample preparation protocols for realization of reproducible characterization of single-wall carbon nanotubes, Metrologia 46 (2009) 682.
166. Y. Xie and D.M. Cwiertny, Use of dithionite to extend the reactive lifetime of nanoscale zero-valent iron treatment systems, Environ. Sci. Technol. 44 (2010) 8649-8655.
39
167. H. Dong, X. Guan, and I.M.C. Lo, Fate of As(V)-treated nano zero-valent iron: Determination of arsenic desorption potential under varying environmental conditions by phosphate extraction, Water Res. 46 (2012) 4071-4080.
168. T. Rojas, J. Sanchez-Lopez, J. Greneche, A. Conde, and A. Fernandez, Characterization of oxygen passivated iron nanoparticles and thermal evolution to γ-Fe2O3, Journal of materials science 39 (2004) 4877-4885.
169. Y. Zhang, Y. Su, X. Zhou, C. Dai, and A.A. Keller, A new insight on the core–shell structure of zerovalent iron nanoparticles and its application for Pb (II) sequestration, J. Hazard. Mater. 263 (2013) 685-693.
170. D.R. Baer and M.H. Engelhard, XPS analysis of nanostructured materials and biological surfaces, J. Electron. Spectrosc. Relat. Phenom. 178 (2010) 415-432.
171. Q. Wang, S.R. Kanel, H. Park, A. Ryu, and H. Choi, Controllable synthesis, characterization, and magnetic properties of nanoscale zerovalent iron with specific high Brunauer–Emmett–Teller surface area, J. Nanopart. Res. 11 (2009) 749-755.
172. A. Liu, J. Liu, B. Pan, and W.-x. Zhang, Formation of lepidocrocite (γ-FeOOH) from oxidation of nanoscale zero-valent iron (nZVI) in oxygenated water, Rsc Advances 4 (2014) 57377-57382.
173. D. Drouin, A.R. Couture, D. Joly, X. Tastet, V. Aimez, and R. Gauvin, CASINO V2. 42-A fast and easy-to-use modeling tool for scanning electron microscopy and microanalysis users, Scanning 29 (2007) 92-101.
40
List of Tables:
Table 1: Summary of studies that have used DLS for nZVI characterisation.
Table 2: Summary of studies that have used XRD for nZVI characterisation.
Table 3: Examples of studies that have used XPS and XAS for nZVI characterisation.
Table 4: Physical and chemical properties of commercial nZVI/ZVI products as reported by the
manufacturers.
Table 5: Iron content of the 5 commercial nZVI/ZVI products: Comparison between the
manufacturers’ data and XRD analysis.
Table 6: Linear combination fitting of the XAS data for the 5 commercial nZVI/ZVI products tested.
Species proportions are presented as percentages. Goodness of fit is indicated by the χ2 value.
Table 7: Coordination parameters of Fe in the samples.
Table 8: Examples of characterisation studies investigating the behaviour of nZVI in different
aqueous media.
41
Table 1: Summary of the different studies that have used DLS to characterise nZVI.
nZVI source Coating
material(s)
Sample preparation before
measurement Concentration
Type of size average
Hydrodynamic diameter (nm) Observations Ref.
NANOFER 25 provided by
NANOIRON Ltd.
Tetraethyl orthosilicate (TEOS)-PVP
Samples were sonicated for different
time periods Not specified Not specified ~ 300
No further effect of sonication when
applied for more than 15 minutes
[85]
Reactive nanoscale iron particle (RNIP) provided by Toda
Kyogo
PSS (3 different PSS-coated nZVI were prepared)
Solution was pre-fractionated and then diluted in DI water and
sonicated for 3 minutes
5 mg L-1
Volume weighted
1 45.6 (6%)/328 (94%)
Bimodal size distribution was
observed for samples containing larger
aggregates. Number weighted data reached
lower particle size.
[86]
2 25 (40%)/367 (60%)
3 24 (100%)
Number weighted
1 26 (98%)/263 (2%)
2 15 (100%)
3 16 (100%)
Bare and sodium polyaspartate-coated reactive nanoscale iron
particle (RNIP and MRNIP) provided by
Toda Kyogo
PMAA-PMMA-PSS triblock
copolymers or SDBS
surfactant
Solution was sonicated with ultrasonic probe
for 30 minutes and then rotated at 30 rpm with an end-over-end rotator for at least 72
hours before measurements
30 mg L-1 Intensity weighted
Bare RNIP 146 ± 4
Larger size than the average primary
particle size determined from TEM
measurements
[22]
MRNIP 66 ± 3 Stable
SDBS-RNIP 36/220
Bimodal size distribution was
observed due to the presence of SDBS
micelles
Polymer-RNIP 1 212 ± 21 Stable
Polymer-RNIP 2 178 ± 11 Stable
42
Bare and sodium polyaspartate-coated reactive nanoscale iron
particle (RNIP and MRNIP) provided by
Toda Kyogo
PMAA-PMMA-PSS
Samples were sonicated in a water
bath for 5 minutes just prior to measurement
300 mg L-1 in 1 mM NaHCO3 and
10 mM NaCl
Intensity weighted
MRNIP 1100 (pH 8)/ 2000 (pH 6)
Aggregation increased with decreasing pH
[88]
Polymer-RNIP
1000 (pH 8)/ 1500 (pH 6)
Reactive nanoscale iron particle (RNIP) provided by Toda
Kyogo
None
Each samples were sonicated for 1 minute prior to measurement
(N.B. the stock solution was pre-
settled for 5 minutes to remove the largest particles (i.e. > 2 μm))
2 mg L-1
Intensity weighted
RNIP
125 after 10 minutes
Aggregation rate increased with
increasing particle concentration
[26]
60 mg L-1 1200 after 10 minutes and reached 20-
70 µm after 30 minutes
Bare and sodium polyaspartate-coated reactive nanoscale iron
particle (RNIP and MRNIP) provided by
Toda Kyogo
Guar gum
Each samples were sonicated for 30 minutes prior to
measurement
231 mg L-1
Intensity weighted
MRNIP 375.4 ± 19.2
Guar gum effectively reduced the
aggregation of RNIP [40]
231 mg L-1 RNIP and 0.5 g L-1 guar
gum
Guar gum-RNIP
162.8 ± 5.7
Lab-made using the sodium
borohydride reduction method
None Not specified Not specified Intensity weighted
67 - [87]
43
Lab-made using the sodium
borohydride reduction method
Carboxymethyl cellulose (CMC)
at different CMC/Fe2+
molar ratio
Measured as prepared
0.1 g L-1 Volume
weighted
CMC/Fe2+: 0.0062
> 3 μm (92.4%)
Large aggregates observed as the ratio CMC/Fe2+ was too low
to stabilise the particles
[21]
CMC/Fe2+: 0.0124
18.6 (81%)/ 161 (5.1%)/ 1460 (13.9%)
Trimodal size distribution
CMC/Fe2+: 0.0186
17.6 (89.5%) -
CMC/Fe2+: 0.0248
15.3 (90.3%) -
1 g L-1 Volume
weighted
CMC/Fe2+: 0.0025
37.2 (45%) CMC is more effective
at higher iron concentration as
nucleation of Fe atoms is accelerated at elevated reagent
concentrations (i.e. Fe2+)
CMC/Fe2+: 0.0031
22.8 (84%)
CMC/Fe2+: 0.0050
19.6 (89.9%)
Carboxymethyl cellulose (CMC)
used a stabiliser to
prepare Fe-Pd nanoparticles
Measured as prepared 0.1 g L-1 Number
weighted
CMC-stabilised Fe-Pd
nanoparticles 17.2 ± 3.2
Good agreement observed among TEM
and DLS measurements [43]
Carboxymethyl cellulose (CMC)
Samples were vortex mixed for 30 seconds prior to measurement
150 mg L-1 Intensity weighted
Bare nZVI ~ 400 - [89]
CMC-nZVI 135 -
Carboxymethyl cellulose (CMC)
Measured as prepared
0.1 g L-1 (0.2 wt.% CMC) Intensity
weighted
0.1 g L-1 61 to 123 (after 1 h) -
[90] 2.5 g L-1 (0.8 wt.%
CMC) 2.5 g L-1 25 to 109 (after 1 h) -
44
Table 2: Summary of different studies that have used XRD for nZVI characterisation.
nZVI source Experimental
conditions/sample preparation Fe-phases identified Other observation Ref.
Lab made nZVI from FeCl3 through borohydride reduction
nZVI particles (2 -5 g L-1) reacted with an aqueous As(III) solution
(1.33 mM) for 24 h; powder diffraction in ambient air
Fe0 and ferrihydrite
No significant change in core–shell configuration due to reaction with As
(III); surface of nZVI particles was decorated with loose debris of
ferrihydrite; grain size of Fe0 core 1 nm
[64]
nZVI (RNIP-10DS) purchased from Toda Kogyo Corp., Japan
Pristine nZVI particles reacted with air under controlled exposure (4 to
50 mL min-1 for 24 h) or rapid atmosphere exposure for 5 min; powder diffraction in ambient air
Fe0, magnetite (Fe3O4) and maghemite (ɤ-Fe3O4)
Intensities of the Fe0 peaks for the modified particles were weaker than
those for pristine nZVI particles due to transformation of Fe0 to magnetite and
maghemite
[35]
Lab made nZVI from FeCl3 through borohydride reduction
nZVI particles synthesised under aqueous ethanol conditions (0, 30,
70, 90, and 100% by volume); powder diffraction in ambient air
Fe0, iron oxides (magnetite and maghemite) and iron hydroxides
(lepidocrocite, bernalite, akaganéite, and goethite)
Increasing ethanol concentrations provided gradually decreasing particle
sizes (20 – 50 nm in no ethanol, 10 – 30 nm in 30% ethanol, 10 – 20 nm in 70%
ethanol, 5 – 20 nm in 90% ethanol and 2 – 5 nm in 100% ethanol) and irregular
amorphous structure
[103]
nZVI purchased from Nanostructured and Amorphous
Materials, Inc. (Houston, TX)
nZVI reacted with dithionite (0.2, 0.9, 1.8 and 3.7 g dithionite g-1 of
nZVI); powder diffraction in ambient air
Fe0, lepidocrocite and magnetite High dithionite concentration caused
green rust formation [166]
Lab made nZVI from FeCl3 through borohydride reduction
nZVI synthesised in aqueous ethanol solutions (70 or 90% ethanol by volume); powder
diffraction in ambient air
Fe0 and iron oxides Appearance of broad α-Fe0 peak due to
short range order structure (amorphous) [113]
Lab made nZVI from FeCl3 through borohydride reduction
Surfactant (Tween®80) modified nZVI (2 mg) reacted with
trichloroethylene (TCE) (20 mL of 29 mg L-1); powder diffraction in
ambient air
Fe0 and γ-Fe2O3 Reaction with TCE caused disappearance of Fe0 peak and prominence of γ-Fe2O3
peak [121]
45
Lab made nZVI from FeCl2 through borohydride reduction
nZVI particles sprinkled on to adhesive carbon tapes supported on metallic disks
Fe0, Fe3O4 and γ-Fe2O3 Fresh nZVI provided prominent Fe0 peak,
oxide peaks dominated with ageing of the sample
[120]
Lab made nZVI from FeCl3 through borohydride reduction and
commercial nZVI product from Kanto Chemical Co., Inc., Japan
nZVI (50 g L-1) reacted with As (III) (100 mg L-1) in 0.01 M NaCl for 1 –
60 days; powder diffraction in ambient air
Fe0, magnetite/maghemite (Fe3O4/ɤ-Fe2O3), lepidocrocite (ɤ-
FeOOH)
Reactions provided a mixture of amorphous Fe-oxide/hydroxide (Fe (II)
and Fe (III)) as the corrosion products of nZVI; crystalline magnetite and
lepidocrocite replaced amorphous phases over 2 months period
[53]
Lab made nZVI from FeSO4 through borohydride reduction
facilitated by dispersant polyvinylpyrrolidone
Powder diffraction in ambient air Fe0 Only evidence of Fe0 formation shown;
broad Fe0 peak appeared due to amorphous structure
[117]
Lab made nZVI from FeSO4 through borohydride reduction
nZVI (20 g L-1) reacted with trinitrotoluene (TNT) (around 3 g L-
1) for 1 h; powder diffraction in ambient air
Fe0 and magnetite/maghemite (Fe3O4/ɤ-Fe2O3)
nZVI corrosion products consisted a mixture of Fe3O4 and ɤ-Fe2O3
[122]
nZVI purchased from Tianjin Kermel Chemical Co., Ltd., China
nZVI (3 g L-1) reacted with acid orange II (100 mg L-1) at pH 3.0, 7.0
and 11.0; powder diffraction in ambient air
Fe0 and lepidocrocite Ferric hydroxides (lepidocrocite –
FeOOH) formed on the surface of the reacted nZVI powder
[123]
Lab made nZVI from FeSO4 through borohydride reduction
nZVI stabilised with polyacrylic acid and polyvinylpyrrolidone; powder
diffraction in ambient air Fe0, FeOOH and FeO
Polymer stabilised nZVI showed no iron peak due to amorphous and non-
crystalline nature [119]
nZVI (Nanofer 25 and Nanofer 25S) purchased from NANOIRON® Company, Czech Republic, EU
Nanofer 25 (150 mg L-1) reacted with As (V) (5 mg L-1) at pH 5 and 9 for 90 min and aged for 30 and 60
days; powder diffraction in ambient air after freeze drying
Fe0, magnetite/maghemite, lepidocrocite, hematite in Nanofer 25; not quantified; no obvious peak for iron oxide appeared in the XRD
profile of Nanofer 25S
Hematite formed at pH 5, but not at pH 9; lepidocrocite and
magnetite/maghemite were the main corrosion products after 30 days,
whereas lepidocrocite predominated after 60 days
[167]
Lab made nZVI from FeCl3 through borohydride reduction
nZVI (50 g L-1in 0.01 M NaCl at pH 7) reacted As (V) (100 mg L-1) for 7,
30, 60 and 90 days; powder diffraction in ambient air
Fe0, magnetite/maghemite, lepidocrocite
Appearance of magnetite/maghemite and lepidocrocite and appearance of
amorphous region in the expense of Fe0 peak after 7 days of ageing; sharp
crystalline peaks of lepidocrocite and magnetite/
maghemite appeared after 30 days; lepidocrocite disappeared after 60 days
onwards
[68]
46
Lab made nZVI from FeCl3 through borohydride reduction
Surfactant (Tween 20) stabilised nZVI; powder diffraction in ambient
air Fe0; no other peak identified
Surfactant stabilised nZVI showed peak broadening due to surfactant artefact
[37]
Lab made nZVI by evaporation of Fe in tungsten (W) boat at 1773o K
under He environment (133 Pa)
nZVI treated under different residual vacuum pressures and temperatures; powder diffraction in ambient air
Fe0, γ-Fe2O3 and/or Fe3O4
Presence of oxide species at the surface of the passivated nanocrystalline
powders [168]
Lab made nZVI from FeCl3 through borohydride reduction
Powder diffraction of ethanol stored sample in ambient air
Fe0 and FeO Broad peak due to amorphous Fe0 and
sharp peak due to crystalline FeO observed
[28]
Lab made nZVI from FeCl2 through borohydride reduction
Powder diffraction in ambient air Fe0, hematite and magnetite
Freshly prepared sample showed only Fe0 peak; oxides peak appear after 2
months of ageing; oxides could not be quantified due to limitation of detection
limit
[125]
Lab made nZVI from FeSO4 through borohydride reduction
with ultrasound assistance Powder diffraction in ambient air Fe0 and FeO
Ultrasound assisted synthesis provided more crystallinity to Fe0
[118]
Lab made nZVI from FeCl3 through borohydride reduction
Powder diffraction in ambient air Fe0
Fresh nZVI with high reductive and adsorptive activity has low crystallinity
of the metal phase and highly disordered iron oxides
[169]
47
Table 3: Examples of studies that have used XPS and XAS for nZVI characterisation.
nZVI source Sample storage/preparation
before measurement Surface chemistry analysis Other observation(s) Ref.
Lab-made using the sodium borohydride
reduction method
After synthesis, sample was diluted with ethanol to prevent particle
from oxidation. For XPS, the sample was dried in a nitrogen-purged
hood at room temperature. Sample preparation for XANES is not
specified
XPS results showed no major changes when sample was aged for 24 hours. The
surface of nZVI consisted of a layer of iron oxides, likely in the FeO form and the
presence of Fe0 was also detected. XANES results of aged particles (i.e. 3
weeks) suggested that the material was composed by 44% of Fe0 and 56% of FeO.
No Fe(III) was observed.
Results from both XPS and XANES confirmed the core-shell structure of nZVI. However, no information on sample preparation for XANES
was provided. Besides, the results obtained with the different instruments are not
comparable since the samples being analysed were different (i.e. different sample preparation, different sample age)
[28]
Reactive nanoscale iron particle (RNIP) provided by
Toda Kyogo
Shell-modified nZVI were prepared by purging air to the particles at
different rates (i.e. 4 to 50 mL min-1 for 24 h) while rapidly oxidised
nZVI were exposed to the atmosphere for 5 min.
XPS results indicate that Fe3O4 and FeOOH are the major shell components of the
"shell-modified nZVI". However, results for the rapidly oxidised nZVI showed no peak
for FeOOH suggesting rapid oxidation favours the formation of iron oxides rather
than iron oxyhydroxides. XANES results confirmed XPS results and
showed more detailed composition of the shell layer of rapidly oxidized nZVI (i.e. FeO;
Fe3O4; α-Fe2O3; β-Fe2O3).
Shell-modified particles were quite resistant to oxidation (upon exposure to atmosphere or
water) and showed very good performance for the degradation of TCE (i.e. 78% of those of
pristine nZVI)
[35]
Reactive nanoscale iron particle (RNIP) provided by Toda Kyogo (FeH2) and lab-
made using the sodium borohydride reduction
method (FeBH)
Samples were prepared in an anaerobic chamber and transferred
into the instrument without exposure to air via a N2-purged
glovebag.
XPS results showed that the FeH2 surfaces were composed mainly of Fe and O (Fe/O ratio of 1.15) with small amounts of S, Na
and Ca while the surfaces of FeBH contained less Fe and S but more B (from the
synthesis chemicals) and a lower Fe/O ratio.
The Fe 2p XPS results showed Fe0 and iron oxides peaks for both materials but the ratios
of Fe2+ and Fe3+ were not quantified. Since XPS is sensitive to the outer 3-5 nm of the nanoparticles, the Fe0 peak in the XPS
spectra confirmed that the shell thickness is less than a few nanometers.
[14]
48
Reactive nanoscale iron particle (RNIP) provided by
Toda Kyogo
Samples were either analysed as-received, exposed to DI water for
24 h or exposed to DI water containing 20 mg L-1 natural
organic matter (NOM) for 24 h
XPS results showed that the oxide shell of the "as-received" nZVI was mainly
composed of Fe(III) while after exposure to DI water and NOM, an Fe(II) component is formed. Results also showed the presence of C and O in the surface of nZVI samples
exposed to NOM which increased the O to Fe ratio.
Authors indicated that it is possible to estimate the thickness of a carbon overlayer on the particles (i.e. due to the presence of NOM)
using two different approaches (put references).
[152, 170]
Lab-made using the sodium borohydride
reduction method
nZVI synthesised in aqueous ethanol solutions (70 or 90%
ethanol by volume). After synthesis, samples were washed with ethanol solution to remove
any by-products from the synthesis then centrifuged, freeze dried and finally transferred to an anaerobic
chamber to be grounded into powdered state before analysis.
XPS results indicated that the oxide shell is mainly composed of γ-Fe2O3 or Fe3O4 (i.e. feature peaks at 531.0 710.9 and 724.4 eV) while a peak at around 706.7 eV revealed
the presence of Fe0.
No further discussion on XPS results was provided.
[171]
Lab-made using the sodium borohydride
reduction method
Fresh synthesised samples were stored in 95% ethanol solution at
4°C prior to use.
XPS results indicated that Hg(II) was sequestrated via chemical reduction to
elemental mercury. For Zn(II), the removal by nZVI was achieved via sorption to the
iron oxide shell followed by zinc hydroxide precipitation. Finally, hydrogen sulfide was
immobilized on the surface of nZVI (i.e. oxide shell) as disulfide (S2
2−) and monosulfide (S2−) species.
XPS results highlighted the various reactive pathways (i.e. reduction, sorption, surface
mineralization) between nZVI (i.e. Fe0 core and iron oxide shell) and targeted contaminants
demonstrating the multiple functional properties of nZVI.
[38]
49
Lab-made using the sodium borohydride
reduction method
Fresh synthesised samples were exposed to oxygen and water for
72 h prior to analysis.
XPS results showed that the surface of the 72 h exposed nZVI was mainly composed of iron oxides and hydroxides. A peak at 711 eV revealed the presence of Fe2O3, Fe3O4, Fe(OH)3 or FeOOH while a peak at 725 eV
suggested the presence of ferric oxides (Fe(III)). Further analysis (i.e. O 1s survey scans) revealed that FeOOH was the main
component of oxidised nZVI.
The combination of XRD, XPS and Raman spectra analysis allowed the accurate
determination of the final corrosion products of oxidised nZVI.
[172]
Lab-made using the sodium borohydride
reduction method
nZVI was exposed to an anoxic As(III) solution (i.e. 1.33 mM) for 22
h before analysis.
Time-dependent in-situ XAS analysis of the arsenic core level showed that As(III)
species go through two distinct transformation stages after adsorption on
the nZVI oxide shell surface: (1) Breaking of the As-O bonds at the particle surface and
(2) Reduction to elemental As and diffusion across the oxide layer to form an
intermetallic phase with the Fe0 core.
Extended EXAFS analysis (i.e. performed at different Fe/As ratio) revealed an
accumulation of partially reduced arsenic at the core/shell interface at large arsenic
content.
[64]
Reactive nanoscale iron particle (RNIP) provided by
Toda Kyogo
nZVI was aged in synthetic groundwater (i.e. exposed to
common groundwater anions or to dissolved oxygen) over 6 months
prior to analysis.
XANES and EXAFS results showed that after 1 month, the different anions inhibited the oxidation of nZVI to varying degrees while after 6 months aging, the oxidation states of nZVI exposed to different anions were very similar except for nitrate which was
able to completely inhibit the oxidation of nZVI, even after 6 months. However, nZVI exposed to water saturated with dissolved oxygen showed a rapid loss of Fe0 within
24 h of exposure.
Linear least-squares combination fitting of the EXAFS spectra indicated that, after 1 month, the system was mainly composed of Fe0 and
Fe3O4 while after 6 months, additional species (i.e. which depends on the anions to which
nZVI was exposed) such as vivianite and iron sulfate species were identified. Results for the nZVI exposed to dissolved oxygen showed the presence of magnetite and maghemite within
the oxide layer.
[109]
50
Table 4: Physical and chemical properties of commercial ZVI products as reported by the manufacturers.
N# Form Colour Fe
content (%)
Solid content (%)
Melting Point (°C)
Density (g cm-3)
Particle Size (µm)
Sold as nZVI
P1 Powder Black 98 100 1536 7.87 0.1-0.25 Yes P2 Powder Dark grey 95.5 100 1536 7.8 70-80 No P3 Powder Dark grey 99 100 1536 7.87 5-50 No S1 Slurry Black 20 20 N/A 1.15-1.25 <0.1 Yes S2 Slurry Black 20 20 N/A 1.15-1.25 <0.1 Yes
Table 5: Iron content of the 5 commercial nZVI/ZVI products: Comparison between the manufacturers’ data and XRD analysis.
Commercial nZVI
Form Fe(0) as per
manufacturer
Iron content analysed using XRD
Zero-valent Iron Iron
oxides/hydroxides (Fe(II), Fe (III))
P1 Powder 98 92 8
P2 Powder 95.5 47 53
P3 Powder 99 34 66
S1 Slurry 100 98 2
S2 Slurry 100 91 9
Table 6: Linear combination fitting of the XAS data for the 5 commercial nZVI/ZVI products tested. Species proportions are presented as percentages. Goodness of fit is indicated by the χ2 value.
Commercial nZVI
Fe(0) Magnetite Maghemite Lepidocrocite Wuestite χ2
P1 79 12 9 0.0001 P2 49 15 36 0.0005 P3 24 28 8 40 0.0040 S1 85 15 0.0001 S2 76 8 8 8 0.0001
51
Table 7: Coordination parameters of Fe in the samples.
Sample Energy shift
Shell Coordination
Number Interatomic bond
distance Debye-Waller
factor Error
DE (eV) CN R (Å) s2 R2
P1 2.87 Fe-Fe1 8 2.49 0.007 4.26
Fe-Fe2 6 2.84 0.012 Fe-Fe3 12 4.10 0.011 Fe-Fe4 24 4.79 0.007
P2 1.19 FeIII-O1 6 1.94 0.013 4.75
Fe-Fe1 8 2.55 0.015 Fe-Fe2 Metal 6 2.79 0.002 Fe-Fe2 Oxide 6 2.94 0.003 Fe-Fe3 12 4.04 0.013 Fe-Fe4 24 4.73 0.017
P3 1.44 FeIII-O1 6 1.97 0.018 5.76
FeII-O1 6 2.19 0.002 Fe-Fe1 8 2.51 0.015 Fe-Fe2 Metal 6 2.72 0.016 Fe-Fe2 Oxide 6 3.32 0.021 Fe-Fe3 12 3.99 0.020 Fe-Fe4 24 4.83 0.030
S1 1.91 Fe-Fe1 8 2.49 0.006 5.47
Fe-Fe2 6 2.83 0.010 Fe-Fe3 12 4.10 0.010 Fe-Fe4 24 4.77 0.007
S2 2.02 Fe-Fe1 8 2.49 0.006 4.16
Fe-Fe2 6 2.84 0.012 Fe-Fe3 12 4.10 0.011 Fe-Fe4 24 4.78 0.007
Fe Metal 1.02 Fe-Fe1 8 2.49 0.003 2.37
Fe-Fe2 6 2.87 0.004 Fe-Fe3 12 4.06 0.005 Fe-Fe4 24 4.76 0.005
52
Table 8: Examples of characterisation studies investigating the behaviour of nZVI in different aqueous media.
nZVI source nZVI
concentration Environmental media Analytical methods Observation(s) Ref.
One lab-made nZVI using the sodium borohydride reduction method and 2
commercial nZVI provided by NANOIRON Ltd. (NANOFER
25 and 25S)
150 mg L-1
pH 8.5, 1-50 mg NaCl L-1 for aggregation study; Synthetic groundwater with different concentration of humic acid for As/Cr desorption study
Laser Light Scattering (LLS) for aggregation study;
Atomic Absorption Spectroscopy (AAS) for
desorption study
Slight variations in particle size with increased ionic strength. Authors explained that the size measured by LLS is the size of the particles remaining in suspension (i.e. first measurement was only taken after 30 minutes) (rest of the particles sedimented in the cuvette). No information on the sedimented particles were provided (e.g. mass fraction). nZVI was found to deposit faster in the presence of Cr and As which was attributed to the precipitation of Cr/As onto the nZVI surface. Desorption of both Cr and As was observed in the presence of typical groundwater conditions and was more pronounced for As.
[155]
Bare and guar gum-coated reactive nanoscale iron
particle (RNIP) (Bare RNIP were provided by Toda
Kyogo)
150 mg L-1 for aggregation
study and 385 mg L-1 for
sedimentation study
pH 7.0, 10 mM NaCl, 0.5 M NaCl and 3 mM CaCl2 for
aggregation study; pH 7.0, 100 mM NaCl and 3 mM CaCl2 for sedimentation
study
Dynamic light scattering (DLS) for aggregation study; UV-vis spectrophotometer
for sedimentation study
During aggregation study, sedimentation of the larger aggregates (sedimentation rate of 0.27 mm min-1 calculated by the authors) likely affected the DLS measurement. Results from DLS and UV-vis measurements are not comparable since different concentrations were used. The electrolyte concentrations tested in this study were much higher than the ones found in groundwater.
[40]
NANOFER 25S (PAA-coated nZVI) from NANOIRON Ltd. and Starch and Tween 20
coated nZVIs prepared in lab from commercial nZVI
NANOFER 25 (NANOIRON Ltd)
100 mg L-1
0-20 mg HA L-1 for aggregation study; 0-10 mg
HA L-1 for sedimentation study
DLS for aggregation study; UV-vis spectrophotometer
for sedimentation study
Both aggregation and sedimentation studies showed enhanced stability of nZVI at higher HA concentration. A two-phase aggregation/sedimentation regime was observed with rapid sedimentation of large aggregates in the first few minutes followed by slow aggregation/sedimentation with time of the remaining particles in suspension.
[150]
NANOFER STAR, NANOFER 25S and NANOFER 25SS
provided by NANOIRON Ltd. 3 g L-1
The three commercial products were aged for 28
days in NanoPure water, 10 mM CaCl2, 100 mM CaCl2
and one groundwater sample under both
anaerobic and aerobic conditions for each media
Inductively coupled plasma atomic emission
spectroscopy (ICP-AES) for total iron concentration;
DLS for particle size; Colorimeter to determine
the ferrous ion concentration; Oxidation-Reduction potential (ORP) measured with a portable
meter
A decrease in particles/aggregates size was observed in the supernatant over time. DLS only measured the smaller particles remaining in suspension while the larger aggregates quickly sedimented in the measurement cell. Reduction in particle size was also explained by the rapid oxidation of nZVI particles. Particles/Aggregates size as large as 7 µm was reported in this study which is far beyond the limit of detection of DLS (i.e. 5 µm).
[156]
53
Commercial nZVI powder provided by Nanostructured and Amorphous Materials,
Inc.
2 g L-1
nZVI suspensions were aged for 1 month in 5, 25 and 100 mN Cl-, SO4
2- and ClO4- and
in 5 and 25 mN HCO3- and
NO3-
X-ray diffraction (XRD) and Transmission electron microscopy (TEM) for
mineralogy study
Both XRD and TEM results confirmed the development of corrosion products in aged samples with the formation of magnetite, carbonate green rust and iron carbonate hydroxide which resulted in decreasing the reactivity of nZVI toward different contaminants.
[154]
Lab-made CMC-nZVI using the sodium borohydride
reduction method 200 mg L-1
0.1 mM and 10 mM NaHCO3
for transport and deposition study
AAS for Fe concentration in the effluent samples
Increased ionic strength enhanced particle deposition of CMC-nZVI. [153]
Lab-made PVP and PAA stabilised nZVI using the
sodium borohydride reduction method
200 mg L-1 pH 7.5; 1, 10 and 100 mM
NaCl
Scanning Electron Microscope (SEM) and
Energy Dispersive X-Ray Spectrometer (EDS) to
determine the deposition mechanism of nZVI and
AAS for Fe concentration in the effluent samples
Increased ionic strength enhanced aggregation and particle deposition of both polymer stabilised nZVI. SEM-EDS results confirmed the attachment of nZVI aggregates onto the sand grains.
[151]
Lab-made Pd/nZVI using the sodium borohydride reduction method
1.7 kg injected over a 2-day
period
Real field scale study in a TCE-contaminated site (Trenton, New Jersey)
ORP and pH measured on site with a portable meter;
Certified analytical laboratory using US EPA standard protocols for
total and dissolved iron, TCE and its daughter
compounds concentration
The TCE reduction observed on site correlated well with the change in ORP at the monitoring location close to the injection well. The correlation was less obvious for the monitoring points located further where a lag period of one to several days was observed between the ORP and TCE decline.
[3]
Lab-made CMC-nZVI using the sodium borohydride
reduction method 900 mg Fe L-1
Field-scale study in a model aquifer
Multi-method approach to monitor the total and
dissolved iron, dissolved oxygen (DO), specific
conductance, pH, ORP
Total unoxidized nZVI was only transported in the first meter and less than 2% of the total injected nZVI reached this distance. Conventional indicators used in field scale studies such as DO, ORP and pH may not necessarily measure the presence of nZVI.
[162]
On-site synthesis of CMC-nZVI using the sodium borohydride reduction
method
1 g L-1 Real field-scale study
(Sarnia, Ontario)
Inductively coupled plasma-optical emission
spectroscopy (ICP-OES) for total iron concentration;
TEM and EDS to characterise the change in
nZVI before and after injection
After 10 days, only 1% of the total injected nZVI was detected from the monitoring well (1 m from injection well) which most likely indicated the deposition of particles on the subsurface porous medium. Measurements of total iron concentration after 48h is believed to be related to dissolved iron in low concentration rather than mobile iron nanoparticles. TEM-EDS measurements showed no morphological changes between the injected particles and the ones recovered from the monitoring well.
[161]
54
List of Figure captions:
Figure 1: The core-shell model of zero-valent iron nanoparticles (adapted from [16]). The core is
made of metallic iron while the shell consists mostly of iron oxides and hydroxides. Thus ZVI
nanoparticles exhibit characteristics of both iron oxides (e.g., as a sorbent) and metallic iron (e.g., as
a reductant).
Figure 2: Bright-field TEM images of a) a single nZVI, b) an aggregate of nZVI and c) TEM image
showing the oxide layer at the surface of an nZVI. [a) and b): Reprinted with permission from ref.
[28] Copyright 2006 Elsevier; c): Reprinted with permission from ref. [62], Copyright 2008 American
Chemical Society]
Figure 3: Top: High-angle annular dark field (HAADF) images of a) fresh ZVI nanoparticle and b) fresh
Fe/Pd bimetallic nanoparticle; Bottom: Corresponding TEM-XEDS intensity map of a) Fe, b) O and c)
Pd in fresh Fe/Pd bimetallic nanoparticles; d) a false colour image of the three components
overlayed. [Reprinted with permission from ref. [63] Copyright 2010 American Chemical Society]
Figure 4: Examples of SEM images of a commercialised sample of ZVI at pH 2: a microparticle imaged
in a) SE mode clearly showing the surface features, b) imaged in BSE mode showing less contrast in
the core, c) an overlay of SE and BSE, suggestive of a lower density surface layer such as a stabiliser
or an oxide layer; d) aggregated nZVI sample; e) nZVI particles isolated for size determination by
adsorbing them onto a poly-L-lysine coated graphite substrate. (FEI Quanta 450 ESEM with FEG
source under high vacuum; a) – c) HV = 20 kV, d) HV = 15 kV, e) HV = 30 kV; WD = 5-10 mm).
Figure 5: Simulated sub-surface trajectories (that collectively map the interaction volume) of 100
electrons from a 10 nm beam of a) 20 kV on Fe, b) 5 kV on Fe2O3, and c) 20 kV on Fe2O3 (Monte Carlo
simulations performed using the CASINO program [173]).
Figure 6: Examples of SEM images of commercialised ZVI samples at pH 2.
Figure 7: XRD patterns of commercial ZVI/nZVI particles. Numbers indicate characteristic iron phase
peaks as follows; 1 = ZVI (Fe), 2 = magnetite (Fe3O4) and/or maghemite (ɤ-Fe2O3), 3 = lepidocrocite
(ɤ-FeOOH), 4 = wuestite (FeO).
Figure 8: Fe 2p XPS analysis of commercialised ZVI particles.
Figure 9: Normalised Fe K-edge k3-weighted EXAFS of the 5 commercial nZVI/ZVI products tested.
Dotted lines show the best 4-component linear combination fit of reference spectra as documented
in Table 5.
Figure 10: Fourier transformed radial distribution functions (RDFs) of the five samples and an iron
metal foil. The black lines in Figure X represent the sample data and the red dotted curves represent
the non-linear fitting results of the EXAFS data.
55
Figure 1
56
Figure 2
57
Figure 3
58
Figure 4
Figure 5
59
Figure 6
60
Figure 7
Figure 8
61
Figure 9
Figure 10