![Page 1: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/1.jpg)
Installation InstructionAL10DB&AL20DBVersion: 1.2
![Page 2: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/2.jpg)
�Installation�Diagram:
Double Latch(Illustrated by the case of AL20DB)
1
B
D
E
FG
A
C
H
C
I
J
K
L
M
![Page 3: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/3.jpg)
A
2
Packing List
F G DNKB C I
HELMJ
HELMJ
56mm 64mm 72mm
25mm 3 5mm 40mm
20mm 30mm 35mm
HELMJ
Mounting hardware package Mounting hardware package Mounting hardware package for door thickness of 30-38mm for door thickness of 39-46mm for door thickness of 47-54mm
Note: To ensure proper functioning of the device only use the mounting hardware package for your door thickness.
![Page 4: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/4.jpg)
Note: Please refer to the above picture to adjust the direction of strike plate F and latch D.
1. Check the door thickness and prepare the corresponding mounting hardware package.
2. Check door opening direction. F
F
F
F
D D
D D
30~38 56 20 10 25
39~46 64 30 10 35
47~54 72 35 10 40
H Spindle Length(mm)
J Screw Length(mm)
M Screw Length(mm)
L Screw Length(mm)
Door Thickness(mm)
3
Door Preparation
Left inward Right inward
Left outward Right outward Standpoint
![Page 5: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/5.jpg)
1) Align the template along the vertical center line of the latch(D) at the desired handle height, and tape it to the door.2) Mark the holes first, and then start drilling.
1.Drill holes on the door. 2.Install the latch (D).
E
center�line�of�the handle
desired�handle height
Installation
4
Note �Installing the mortise(D) on the door : by inserting screws(E).
E
D
![Page 6: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/6.jpg)
3.Install outdoor unit (B) with gasket (C) and spindle (H) on the door.
5
H
BC
3.3 Attach outdoor unit (B) to door by putting it through door holes.
3.2 Insert spindle (H) into the clutch.
3.1 Put gasket (C) on outdoor unit (B).
Right open: Please insert PM3 screw on the R side Left open: Please insert PM3 screw on the L side
![Page 7: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/7.jpg)
4.Install mounting plate (I) with gasket (C) on the door.
J
5.Install indoor unit (K).
M L
6
I C
L
M
BC
J
4.1 P ut m ounting p late (I) o n g asket(C). 4.2 I nserting s crews(J) t o s ecure t he o utdoor u nit.
5.3 Secure indoor unit (K) to outdoor unit (B) by inserting screws (M) and screw (L).
5.1 Connect the indoor unit (K) cable to the o utdoor unit (B). 5.2 Push the cable into the hole.
![Page 8: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/8.jpg)
23mm[29/32"]12
6mm[4�49/64
"]
18.5mm[47/64"]
22mm[55/64"]
3.5mm[9/64"]
88.4mm[3�31/64
"]
6.Insert batteries. 7.Mark and drill holes for the strike.
8. Test the lock by rotating the back handle and using the mechanical Key (A).
Note:1) When the door is locked and the clutch is idle, the front handle can be turned, but the door will remain locked.2) When you are inside the door, turn the handle upward to lock the deadbolt for more security. When you go out, verify your fingerprint first, and then turn the handle up to lock the door for the safety of your property.
6.Insert batteries.
K
7.Mark and drill holes for the strike.
Note:1) When the door is locked and the clutch is idle, the front handle can be turned, but the door will remain locked.2) When you are inside the door, turn the handle upward to lock the deadbolt for more security. When you go out, verify your fingerprint first, and then turn the handle up to lock the door for the safety of your property.
7
E GF
8. Test the lock by rotating the back handle and using the mechanical Key (A).
![Page 9: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/9.jpg)
Change latch (D) direction.
A
How To Use Mechanical Key And Change Handle Direction?
How To Use Key & Changing Handle Direction?
8
Hexagon Screw
N
Hexagon Screw
N
2. �Pull handle away from l ock.
1. Use wrench (N) to remove screw.
3. �Insert �mechanical �key �into �hole� to o� pen t�he d� oor.
2. �Pull handle away from l ock.
3. �Change handle direction and replace.
4. ��Replace the screw on the opposite side.
1. Use wrench (N) to remove screw.
1.Push the switch to the end2.Push the latch bolt into mortise3.Rotate the latch bolt at 180° inside mortise, then loose it.�
Œ
Ž
![Page 10: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/10.jpg)
9
Remarks
1. The default setting of the device allows ANY fingerprint to unlock.
2. Please register at least one administrator for the newly installed lock. Without �administrator, no
registration for any normal user is allowed.
3. The lock is equipped with mechanical keys for manually unlocking. Please keep the mechanical keys in a
safe place.
4. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and
rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. Please replace the battery soon when the lock prompts the voice of low battery.
7. If there is no activity performed on the lock for 10 seconds the fingerprint sensor will go to sleep.
8. For best results, apply clean fingers to the fingerprint sensor.
![Page 11: AL10DB&AL20DB Instalatlion InstructionV1.2-20180522](https://reader030.vdocuments.mx/reader030/viewer/2022012616/619ecb250450b86f3636840c/html5/thumbnails/11.jpg)
www.zkteco.eu
© Copyright 2017. ZKTeco Inc. ZKTeco Logo is a registered trademark of ZKTeco or a related company. All other product and company names mentioned are used for identification purposes only and may be the trademarks of their respective owners. All specifications are subject to change without notice. All rights reserved.