→ The 6kN Pile Fixing must be installed in accordance with this brochure
→ Auckland University Tested Ref. 4613
→ All Subfloor construction must be in accordance with NZS 3604:2011
→ NZS 3604 requires lines of lateral support to floor joists within 300mm of bearer or bracing lines, refer clause 7.1.2
→ Joists deeper than 150mm require solid nogging over cantilever pile
80
20 2080
SCAN FOR INSTALLATION
VIDEOhttps://vimeo.com/117351500
2 x STAINLESS STEEL WIRE DOGS PER SIDE
Free Nail Area
6kN
6kN
CT160 CLEATS H.D.G OR STAINLESS STEEL - 4 PER PILE
3 NAILS INTO BEARER AND JOSIT
2 X 90MM H.D.G or Stainless Steel nails skew driven
4 x 90mm Stainless Steel nails skew driven
2 up into Bearer2 Down into the Pile
SQUARE PILE
CODE PRODUCT FINISH OPTIONS
STANDARD PACK
6KN
- Pile to BearerWire Dogs & NailsSTAINLESS STEEL- Joist to Beaerer
Cleats & NailsHOT DIP GALVANISED
HIGH CORROSION
PACK
6KNH
- Pile to BearerWire Dogs & NailsSTAINLESS STEEL- Joist to Beaerer
Cleats & NailsSTAINLESS STEELCantilever Pile Shown
(on internal bracing line)
www.miteknz.co.nz© Copyright 2020 MiTek Holdings, Inc. All rights reserved. Mar 2020
6kN PILE FIXINGFOR CANTILEVER PILES
AVAILABLE FROM LEADING BUILDERS SUPPLY MERCHANTS THROUGHOUT NEW ZEALAND
www.miteknz.co.nz© Copyright 2020 MiTek Holdings, Inc. All rights reserved Mar 2020
6KN PILE FIXING2 x 90mm H.D.G or Stainless Steel nails skew driven Joist
20mmNail Free area
300 Scarf (max.)
Wire Dogs4 x Stainless
Steel
CT160 Cleats perPile3 x nails per Joist and Bearer
20mmNail Free area
Scarf squarePile face for
Wire Dogs30 3065
4 x 90mm Stainless Steel nails skew driven into Pile. (1 each side)
SQUARE PILE DETAIL
Pile
Round Pile Shown.(140mm min.)
85mm min.
CORROSION HAZARD USE TABLEStandard Pack 6KN- Zones B & C- If Joist to Bearer fixing ABOVE 600mm from ground level
Pile to Bearer fixings Stainless Steel (304). Joist to Bearer fixings Hot Dip Galvanised
HIgh corrosion pack 6KNH- Zone D- All fixings BELOW 600mm from ground level
All items Stainless Steel (304).
6kN Joint Fixing SchedulePILE to BEARER - Wire Dog Staple (4 per joint) Stainless Steel - 4 x 90mm skew nails (1 per face) Stainless Steel
JOIST to BEARER - CT160 Cleats (4 per pile) 160mm long - 3 nails per Cleat into Joist - 3 nails per Cleat in Bearer - 2 skew nails 90mm (1 per side) NAILS - 24 x 45mm 3.55 dia. spiral nails. - 4 x 90mm x 4 dia. St nails (6KN pack only) - 8 x 90mmx 4 dia. St nails (6KNH pack only)
85mm min.
Left Hand Shown
Right Hand Shown
Wire Dogs x 4
CT160LHCT160RH
EXTERNAL BRACING LINE
Wire Dogsbent on site to allow each prong to enter each timber surface at 900
6kN Pile Set Contents4 x Stainless Steel Wire Dogs4 x CT160 Cleats24 x 45mm 3.55 dia Sprial Nails90mm Stainless Steel nails to suit (4-6KN pack / 8-6KNH pack)
