1 25 VFS OI 07-A-10, 25 Jul 2011
BY ORDER OF THE COMMANDER 25 VFS OPERATING INSTRUCTION 07-A-10
25th Virtual Fighter Squadron 25 Jul 2011
Combat Operations
A-10C Ground Weapon Employment
COMPLIANCE WITH THIS PUBLICATION IS MANDATORY
______________________________________________________________________________ OPR: 25 VFS, Snoopy Certified by: Raven6
Pages: 58
Distribution: 25 VFS
______________________________________________________________________________
This operating instruction (OI) provides Guidance on Ground Weapon Employment in the A-10
Thunderbolt II.
SUMMARY OF CHANGES
None, Document based on AFTTP 3-3, Combat Aircraft Fundamentals, A-10.
1. PURPOSE: The purpose of this document is to provide guidance and training for ground
weapon employment in the A-10C and will be used within the 25th VFS.
2. INTRODUCTION: The A-10‟s primary mission is close air support (CAS). This OI
provides the fundamental tools to build precise weapons delivery skills essential to CAS:
fundamentals of bomb theory, conventional range patterns and development of tactical delivery
references, computed bomb deliveries, manual bomb deliveries, and forward firing deliveries.
3. Weapons Delivery Terminology. In order to understand the discussion on free-fall weapons
delivery, be familiar with the following terms and definitions: (See Figure 7.1, Bomb Triangle.)
• Aim-off distance (AOD)—A distance beyond the target that is predictable for any weapons
delivery. That distance is the no-wind projected flight path of an aircraft (where the aircraft
would hit the ground if the pilot did not recover) in a dive delivery.
• Aim-off point (AOP)—The point on the ground, long of the target, at which the aircraft must
fly to during the weapon‟s delivery pass. The AOP provides a ground reference to fly the aircraft
to until a track reference can be set.
• Angle of attack (AOA)—The angle between the zero sight line (ZSL) and the relative wind.
• Ballistic trajectory—The path of a munition from release to impact. This trajectory is a result
of release velocity, release angle, release height above the target, gravity, and weapon drag
characteristics.
• Bomb range (BR)—The horizontal distance the bomb will travel over the ground from release
to impact.
• Bomb trail (BT)—The horizontal distance between the aircraft and the bomb impact.
• Combat offset—Adjusting the RAP by a certain distance to correct for a previous miss.
• DB— dive bomb.
• Dive angle—The angle of dive for weapons delivery.
2 25 VFS OI 07-A-10, 25 Jul 2011
• Gun bore line (GBL)—Represents the initial bullet muzzle velocity vector extended to
infinity. This is the depression from the ZSL where the bullets initially come out of the gun. The
A-10 GBL is at 33.7 mils depression. The GBL is sometimes used to approximate the aircraft
vector on roll-out because the total velocity vector (TVV) lags the actual aircraft flight path.
• HADB— high altitude dive bomb.
• HARB— high altitude release bomb.
• HAS— high angle strafe.
• HATR—high angle tactical rocket
• Initial Pipper Placement (IPP)—Angle between the target to the total solution in mils at track
altitude.
• Initial HUD Placement (IHP)—IHP is the angle at track altitude between the ZSL and the
target, in mils. IHP can be derived from the total mil setting and the value for IPP. Total Mils =
IHP + IPP.
• Initial Aim-off Angle (IAA)—IAA is the angle between the AOP and the target at track
altitude.
• Initial Target Placement (ITP)—ITP is the position of the target relative to a pitch ladder at
track altitude.
• LALD—low-angle low drag.
• Mil—A term commonly used by A-10 pilots as an abbreviation for milliradian (1/1,000th of a
radian). Mils are used to measure sight depression or relative positions and sizes of objects as
seen through the HUD. One mil is equal to 1 foot at a range of 1,000 feet, and 1 degree equals
17.45 mils.
• Relative wind—The speed and direction of the air mass relative to the aircraft. It is opposite in
direction to the aircraft‟s velocity vector through the air mass.
• Release aimpoint (RAP)—The wind-corrected point on the ground where the pipper must be
placed at release for the munition to strike the target.
• Release aimpoint extended (RAPE)—The point on the ground on which the aircraft track
reference is set. This point is corrected upwind from the RAP.
• Release altitude—The altitude above the ground at which weapons delivery is accomplished.
• Roll-in Target Placement (RTP)—A cockpit reference used to establish an aim-off angle for
the aircraft.
• Total sight setting (TSS)—The depression from the ZSL to the target at release altitude for the
planned release conditions. Deviations from planned release parameters such as airspeed, dive
angle, altitude, or G-loading will have an effect on the planned total sight setting.
• Track reference—A position or point in the HUD that is used to maintain or correct the
aircraft to the planned wire. Some common track references used in weapons delivery are IHP,
IAA, IPP, and the desired release cue (DRC).
• Tracking—A portion of any dive weapons delivery that is devoted to the final alignment of
aircraft sighting systems with the target. The amount of time associated is referred to as wings-
level or tracking time.
• Zero sight line (ZSL)—A basic reference line extending through the fuselage of the A-10
parallel to the longitudinal axis of the aircraft. All sight depressions are referenced from the ZSL.
3 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.1 Bomb Triangle.
4 Preparation.
4.1. General. Weapons delivery training in the A-10 requires a thorough understanding of
training rules, weapons delivery theory, head-up display (HUD) symbology, aircraft systems
knowledge and basic range layout and administration. (See Figure 7.2, A-10 Air-to-Surface
Weapons Employment Cockpit Interface.)
4 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.2 A-10 Air-to-Surface Weapons Employment Cockpit Interface.
5. Range Administration.
5.1. Range Entry and Exit. Written procedures and guidance can be found in command
directives, applicable supplements, and local directives. Normally, entry to the controlled range
as accomplished from a basic or tactical formation, depending on weather and/or spacing
desired.
5.2. In-Flight Checks. Weapons delivery “in-flight checks” encompass nearly all systems on the
A-10. They include fuel checks, weapons system checks, wind checks, estimated vertical error
(EVE) checks, and a needle/ball check.
5.2.1. Fuel Checks. These are normally initiated and executed on the primary range frequency.
At an absolute minimum, fuel checks are required prior to range entry, once while on the range,
and once upon exiting the range.
NOTE: Be extremely careful not to become distracted and drop them out of the cross-check.
5.2.2. En Route Checklists. There are certain checks that need to be accomplished before
reaching the target area; these are collectively known as a “firepower, emitters, navigation,
communications, and electronic countermeasures” (FENCE) checks. A FENCE check simply
groups the items that need to be covered and is generic to any aircraft. Perform a FENCE check
prior to weapons employment, including weapons switches set for the first pass. For training
missions, do not place the Master Arm to ARM until entering the range and cleared by lead. A
common A-10 acronym is listed in Figure 7.3, FENCE Checks, along with the items covered in
5 25 VFS OI 07-A-10, 25 Jul 2011
a generic FENCE check. The FENCE check is an ongoing process. Start with a pre-takeoff
FENCE check and accomplish another one for each phase of flight. Before arriving at the IP, the
aircraft must be ready for combat. Once in the target area, your focus must be on finding and
attacking the proper target.
5.2.3. Weapons System Checks. The Weapons portion of the FENCE check requires
amplification to correctly set up weapons for employment. Disciplined weapons system checks
are critical to mission success. When directed by the flight lead (FL) perform a Weapons System
Check. Reference Figure 7.4, Common Weapons System Checks, for two common Weapons
System Check acronyms.
5.2.4. Wind Checks. Analyzing winds is critical for accurate and consistent weapons delivery.
Analyze winds by using your EGI readings (i.e., select STR INFO page on EGI) and visual
indications provided by dust or smoke. Winds affect every aspect of the weapons delivery
pattern and should be accounted for in flight.
F-E-N-C-E C-W-L-I-T-T-E-R
F Fire control systems set. Weapon
system checks..
Gun armed. EO power on. Target
identification set.
C Chaff/flare. CMS set to appropriate
settings.
E Electronic warfare systems. CMS
set. W Weapons. Conduct weapons system
checks
N Navigation. EGI, map, and
TACAN ready. Wind checked. L Lights. OFF.
C Communications. Frequencies set, I N/A for DCS A-10C
E Emitters (reduce or select).
TACAN set. External lights OFF. T TACAN. Set to receive only or off.
T Tape. DVADR running.
E ECM as appropriate.
R RWR as briefed.
Figure 7.3 FENCE Checks.
S-P-A-D-E-S A-P-E-S
S Switches Set. A Arm.
P Profile Selected. P Profile, DSMS.
A Altitude Source. E Elevation source.
D DSMS quick-look (for stations and
profile settings). S SOI, SPI.
E Elevation set as briefed.
S SOI and SPI set as briefed.
Figure 7.4 Common Weapons System Checks.
6 25 VFS OI 07-A-10, 25 Jul 2011
5.2.3. Radio Transmissions. Standard and expected radio transmissions while operating on the
conventional range may vary; however, the basics remain the same. (See Figure 7.5,
Conventional Pattern and Methodology, for example radio calls.)
5.2.3.1. All radio transmissions while in the range pattern will be made on the respective range
frequency.
5.2.4. Spacing. Spacing will be established by the Flight Lead. Typical two-ship spacing in the
container pattern is on opposite corners, or “180 out.” For example, when Number One is rolling
in on final, Number Two is turning crosswind to downwind. (See Figure 7.5, Conventional
Pattern and Methodology.) For a four-ship, the standard spacing is one aircraft on each of the
four corners. Establishing a contract for when flight members turn crosswind will aid in
maintaining spacing. Corrections to pattern spacing, for both a two-ship and a four-ship, should
be made on the turn from crosswind to downwind by varying the point at which the turn is made.
Figure 7.5 Conventional Pattern and Methodology.
7 25 VFS OI 07-A-10, 25 Jul 2011
5.2.5. Contingencies. Contingencies that could be encountered on the range must be briefed.
The basic rules apply: maintain aircraft control, climb away from the ground while analyzing the
problem, and call a “KNOCK IT OFF” if required on the range frequency.
5.2.5.1. Lost Sight. The most common contingency is losing sight of one or more flight
members. If blind on the preceding aircraft, immediately request the aircraft position. An
example in a four-ship formation, if Warthog Three loses sight of Two: “DRAGGIN TWO, SAY
POSITION.” Number Two should respond immediately with two‟s position in the conventional
pattern. Number Three then has two responses, “CONTINUE” or “KIO.” The continue call is
made when Number Three picks up a visual on Number Two or determines that there are no
deconfliction problems in the pattern. If positive separation cannot be immediately ensured, then
Number Three should “KIO” (with altitude, as a technique) to ensure safety of flight. It is
important to remember that if a “SAY POSITION” call is made, particularly within a four-ship,
all aircraft must remain silent until the aircraft being addressed responds with its position and the
requesting aircraft confirms the response with “CONTINUE” or “KIO.”
5.2.5.2. Lost Comm. If NORDO on range, then continue to fly the briefed range pattern.
However, on final (DRY) rock wings to indicate to the RCO and fellow flight members of the
NORDO condition. Expect a rejoin followed by RTB. If NORDO with emergency, then rock
wings on final then turn opposite direction to normal range traffic. Expect a rejoin and be
prepared to communicate problems with HEFOE visual signals.
5.2.5.3. Weapon Malfunction. Inform lead of any suspected weapon malfunctions, then follow
local range procedures.
5.2.6. Conventional Pattern. Since much of basic weapons delivery training will be performed
on a conventional range, familiarity with the mechanics of flying the patterns are discussed next.
5.2.6.1. Crosswind. When turning crosswind, be careful not to turn inside the preceding aircraft.
For collision avoidance purposes, it is critical that each aircraft fly their turn from final to
crosswind as briefed by FL. A typical technique for high release altitude deliveries is to turn
crosswind at track altitude. After accomplishing the safe escape maneuver, visually reacquire the
preceding flight member by first clearing the crosswind to downwind corner, then clearing the
downwind to base corner. Additionally, expect the range control officer (RCO, or ranger) to
report the last event score while on crosswind, or making the turn to downwind. Acknowledge
this transmission IAW local guidance and the flight brief.
5.2.6.2. Downwind. All pattern corrections to flight spacing should be made on the turn from
crosswind to downwind. This will minimize variations and adjustments to the base leg turn. Due
to aircraft potentially turning crosswind at different points, the turn from crosswind is the most
dangerous portion of the pattern, and is known as the “coffin corner.” Ensure positive visual
contact with previous flight member to ensure deconfliction. If ever in doubt of the position of
the previous flight member, follow the procedures outlined in paragraph 5.2.5, Contingencies.
The displacement from the target (downwind spacing) is not exact and is typically flown 2 to 3
NM from the target. Downwind displacement should be wide enough to allow for adequate
wings-level time while on the base leg. Plan to be at base altitude no later than when making the
8 25 VFS OI 07-A-10, 25 Jul 2011
turn for the base leg. While on downwind, take the time available to assess the last pass and
prepare for the next one.
5.2.6.3. Base. Do not adjust the position of the turn from downwind to base leg as it can
adversely affect the weapons delivery parameters on the upcoming pass. Anticipate the turn to
base and lead it using as little G as possible. As a ROT, the base turn radius will be
approximately 3,000 feet. Use known, wind-corrected GEOREFs to start the base turn. Fly a
precise base leg to put the aircraft in the best position to roll in and achieve the planned
parameters (e.g., airspeed, altitude, and dive angle). Approaching the roll-in point, note the
relationship of the target to the canopy rail in order to develop/validate tactical canopy
references.
5.2.6.3.1. Known Ground Track. The base leg must be consistent to get the aircraft on the correct
wire relative to the target. A geographic reference (GEOREF) is a good starting point for finding
the correct base position. The goal is to develop and validate a canopy rail reference on the
conventional range that can be applied to a tactical situation without known ground references.
5.2.6.3.2. Canopy Rail Reference. A-10 pilots should use canopy references based on the initial
target placement (ITP) for the delivery as the primary method to establish a tactical base
position. Although ITP is measured at track altitude, it is an accurate sight picture for target
placement at base position.
5.2.6.4. Final Leg. The final is the weapon delivery portion of the pattern, and clearly “where the
rubber meets the road.” A technique to dissect this complicated maneuver is “Pull, Center, Set.”
This phrase leads an attack pilot through each step of the final leg. The actual cross-check and
procedures used to put the release aimpoint on the target will vary depending on the delivery and
delivery mode.
5.2.6.4.1 Roll-In Timing. For lower angle deliveries (e.g., 30 degrees or less), start with the
target about 20 to 30 degrees in front of the wing line (i.e., 10 or 2 o‟clock position, depending
on direction of roll-in). A technique is to start roll-in when the target is just aft of the canopy
bow. For deliveries greater than 30 degrees, delay the roll-in until the target is approximately
three fists aft of the canopy bow, since most of the turn for these deliveries are made in the
vertical. Consider the winds at pattern altitude and adjust the final roll-in point as necessary (i.e.
if encountering a headwind while on base, delay the roll-in, similar to perch corrections in the
traffic pattern).
5.2.6.4.2. Pull. Mechanically, execute a roll-in by advancing the throttles to MAX, start an
unloaded roll to 80 degrees plus the dive angle, and begin a 2- to 3-G turn (normally the steady
tone). On a conventional range and attempting to validate tactical delivery references, have a
known aim off point for the delivery, and fly the aircraft to the AOP. Don‟t forget to adjust for
winds.
5.2.6.4.3. Roll-In Target Placement (RTP). After developing and validating base canopy rail
references, pilots should develop a roll-in target placement to aid in establishing a proper aim-off
distance for the base position flown. Establishing and using RTP can place the jet on a correct
9 25 VFS OI 07-A-10, 25 Jul 2011
wire using a cockpit reference during roll-in, without the aid of aim off distance markers in a
tactical environment. This allows pilots to correct for small base position errors in a tactical
situation and minimize large track corrections on final.
5.2.6.4. Initial Target Placement. During the roll-in, an opportunity to refine the dive angle
exists by cross-checking the pitch ladders. If using ITP as a roll-in (not track) reference, as the
nose of the aircraft is halfway around the final turn, use the HUD pitch ladders to estimate if the
target will be located at the appropriate angle when the aircraft rolls out. If the expected target
placement in the HUD is less than planned, relax back pressure, decrease bank, and adjust the
AOP longer than planned. The longer the nose is kept up during the turn (sometimes referred to
as “floating” the turn), the steeper the aircraft will be after setting the AOP at track. Likewise, if
the angle in the HUD is greater than expected during the roll-in, increase bank angle and G to
adjust the AOP shorter than planned.
5.2.6.5. Roll-Out (Center). Begin to relax G during the roll-in as the top of the HUD approaches
the target. For computed deliveries, as the HUD pitch ladders approach the edge of the target,
begin an unloaded roll-out. The pitch ladders should bracket the target when the roll-out is
complete. If the target is not centered within the pitch ladders, aggressively make an appropriate
3/9 correction to center the target. If the target is within approximately 30 mils of the CCIP
pipper (just outside of the reticle), place the PBIL through the target and set a track reference.
After roll-out, set the throttle to achieve the planned airspeed at release.
5.2.7. Track References (SET). Regardless of the type of delivery flown (manual or computed) a
track reference must be set. These track references are presented below.
5.2.7.1 DRC. The best track reference that may be used for CCIP WD is the DRC. After using
one of the valid roll-in techniques, set the DRC at track altitude. The DRC continuously
computes and corrects for changes in airspeed, AOA, and G-loading. Setting the DRC corrects
the aircraft flight path toward the expected time of fall driving it toward the “correct wire.”
Because weapons employment mils are based on a specific track altitude and airspeed, a
technique for using the DRC is to set the DRC on the target at track altitude. Setting the DRC in
this manner establishes and refines the AOP for a correct wire, just like setting an IPP does for
manual deliveries. Since the aircraft will accelerate on final, the DRC will track down slightly as
the pipper tracks up during the pass. Set it and forget it. Hold the AOP and do not make a Banana
pass by trying to hold the DRC on the target. Keep the minimum release staple (MRS) in your
cross-check as your abort cue. Since the DRC is continuously computed, it is wind corrected and
valid at all altitudes during the pass. So if unable to set the DRC at Track, a pilot should still set
the DRC as soon as possible.
5.2.7.2 IHP/IPP. IHP is an angular representation (in mils) of the target relative to the ZSL. The
depressible pipper is available in CCIP mode before designation. One technique used is setting
IHP mils in the depressible pipper. In any case, the pilot needs accurate wind information and
then must add/subtract the applicable head/tail wind component. Note that the depressible pipper
does not provide crosswind correction on final. Therefore, it is imperative to center the target
between the pitch ladders, cross check the target abeam the depressible pipper at track altitude,
and continue with a normal track until release. Any HUD reference with a mil depression
10 25 VFS OI 07-A-10, 25 Jul 2011
corresponding to the IHP may also be set abeam the target. These references must be used for
manual weapon‟s delivery if IHP is used as the track reference; however, IPP is the
recommended track reference to use during manual weapon‟s delivery. (See Figure 7.6,
Bombing Triangle—Initial Head-Up Display Placement and Initial Pipper Placement Triangle,
for a visual depiction of this track reference.)
Figure 7.6 Bombing Triangle – IHP and IPP Triangle.
5.2.7.3. IAA. IAA is the planned angle between the AOP and the target at track altitude. (See
Figure 7.7, Bombing Triangle—Initial Target Placement/Initial Aim-Off Angle, for a depiction
of the reference.) Let us look at an example delivery with an IAA of 5 degrees. To set the correct
wire, set the TVV 5 degrees long of the target. Regardless of where the aircraft is in relation to
the planned wire, this will establish the correct wire. When employing manually, IAA must be
corrected for head wind or tailwind. To correct IAA for winds, there are 17.45 mils per degree;
therefore, for each 17 mils of wind correction, add or subtract a degree. For example, with a 10
knot headwind, use a 1.7 mil per knot correction factor for headwind/tailwind and add 1 degree
to IAA (17 mils).
5.2.8. Confirm the Aircraft Parameters. After setting the track reference at track altitude, confirm
aircraft parameters are within abort criteria. Continue to cross check parameters while flying to
the release point.
5.2.9. Pipper Track. Fly smooth, coordinated control inputs on final. During the dive, divide
attention between the movement rate of the pipper and the aircraft‟s parameters. Concentrate on
letting the sight track to the release aim point (RAP). For computed deliveries, utilize the
projected bomb impact line (PBIL) to fly the CCIP pipper to the target or combat offset point.
The CCIP pipper will track quickly to the target. Avoid attempting to slow the pipper down by
11 25 VFS OI 07-A-10, 25 Jul 2011
bunting the aircraft as this can induce release errors. One technique to help a smooth pipper track
is to trim forward one „click‟ for each 10 degrees of planned dive. This can be accomplished on
base, but will cause a heavy stick. Trim through the roll-in, or after setting track.
Figure 7.7 Bombing Triangle—Initial Target Placement/Initial Aim-Off Angle.
5.2.10. Pickle. Release the weapon with the aiming reference on the intended release aim point.
Combat offset can be used to improve subsequent pass accuracy. If a previous delivery was
completed with the aiming reference on the target, and the weapon did not hit the target, perform
a “combat offset.” As a ROT, offset the aimpoint one half the miss distance in the opposite
direction of the previous miss. As an example, if the first weapon impacted 50 meters at 2
o‟clock, on the second pass, release the weapon 25 meters at 8 o‟clock.
5.2.11. Recovery. Start a recovery after ordnance release, reaching the abort cue, or if you lose
SA. For free-fall munitions, the primary concerns during recovery are hitting the ground (or
descending below a desired altitude), delivering a weapon with a time of fall below the minimum
fuze time (a DUD weapon), or being hit by fragmentation from the ordnance employed. The
planned recovery maneuvers for free-fall munitions are the climbing maneuver (CLM) and
turning level turn (TLT) safe escape maneuvers (SEM). As a general rule, for low-altitude
deliveries, 20 degrees or below, execute a TLT SEM, and for deliveries above 20 degrees,
execute a CLM SEM. Computed deliveries use real time safe escape to display an abort cue, and
manual deliveries use an abort altitude.
5.2.12. Execution. It is important to understand that when executing the SEM, it must be
executed immediately after weapons release. Safe escape maneuvers include the climbing SEM,
TLT SEM, and the back-up SEM. Maintaining the minimum aircraft G for the duration of the
maneuver is critical in achieving safe escape or safe separation as appropriate.
12 25 VFS OI 07-A-10, 25 Jul 2011
5.2.12.1. Common Errors. CLM SEM errors include: insufficient G during the recovery,
exceeding 30 degrees of bank prior to 30 degrees nose high, and not completing the maneuver to
30 degrees nose high. TLT SEM errors include: an unloaded roll as the nose approaches the
horizon, excessive nose high or nose low during the turn, rolling out prior to completing 60
degrees of turn, and most importantly, not maintaining G on the aircraft until the TLT SEM is
complete.
5.3. Pop-Up Pattern. The pop-up is an “unmask” maneuver used at low-altitude to visually
acquire the target. It can be used for free-fall, gun, rocket, and Maverick attacks.
The approach (approach course) to the target can be either straight ahead or offset depending on
the desired attack axis to the target. However, the approach course is generally 45 degrees offset
from the final attack heading when employed from a conventional pattern. A 45-degree offset
offers a balance of target acquisition, turning room to reposition for the pull-down, and exposure
to threats. When employed tactically, the goal should be to strive for 3 seconds wings-level time.
The pop-up point will vary depending on the ordnance to be employed. The tasks associated with
each leg of the pop-up pattern are generally the same as the conventional pattern, with the
following exceptions and the pop-up maneuver itself. Review the following pop-up specific
terms while referencing Figure 7.8, Pop-Up Pattern, and Figure 7.9, Pop-Up Pattern Analysis:
• Run-in altitude—The altitude above or below target elevation.
• Approach course—The ground track the aircraft flies until reaching the pop-up point (pull-up
point [PUP]).
• Attack heading—Final attack heading.
• Angle-off (AO)—The angular difference between the approach course and attack heading.
• Pull-up point (PUP)—The point along the approach course at which the pull-up to the climb
angle is initiated. Fly to the target from the PUP.
• PUP angle off nose (AON)—The angular difference between the approach course and a line
directly to the target from the PUP.
• Climb angle—The angle-of-climb that is to be achieved following the initiation of the pop-up.
• Pull-down point (PDP)—The start point for a maneuver to transition from the climbing to the
diving portion of the pop-up delivery.
• Pull-down target placement (PTP)—Sight picture used to initiate pull-down.
• PDP angle off nose (AON)—The angular difference between the approach course and a line
directly to the target from the PDP.
• Apex—Highest altitude the aircraft reaches during the pop-up profile.
• Dive angle—The planned dive angle for weapons delivery.
• Aim-off distance (AOD)—A distance beyond the target that is predictable for any weapons
delivery. That distance is the no-wind projected flight path of an aircraft
(where the aircraft would hit the ground if not recovered) in a dive delivery.
• Tracking—A portion of any dive weapons delivery that is devoted to the final alignment of
aircraft-sighting system with the target.
• Minimum attack perimeter (MAP)—Is a circle centered on the target, which depicts the point at
which target tracking is initiated. Using track altitude as a point on the ground, the distance from
the target to this point is the radius of the circle.
• Release altitude—The altitude above the ground at which weapons delivery is accomplished.
13 25 VFS OI 07-A-10, 25 Jul 2011
• Bomb range—The distance the bomb will travel over the ground from release to impact.
Figure 7.8 Pop-Up Pattern.
14 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.9 Pop-Up Pattern Analysis.
5.3.1. SEM and Crosswind. The SEM employed is generally a TLT. Upon completion of the
SEM, establish a climbing vector and complete the turn to crosswind. Remember to check the
crosswind to downwind corner, and then downwind to base corner, for preceding aircraft.
5.3.2. Downwind. The downwind leg can either be parallel to the run-in leg (45 degrees offset
away from the target) or parallel to the final leg. The considerations for actions on downwind are
similar to those in the conventional pattern, except the aircraft will typically be 1,500 to 2,000
feet AGL.
5.3.3. Base. The turn from downwind to base is where the pop-up pattern diverges from the
standard conventional pattern. During the turn to base the aircraft needs to descend and turn to
arrive on the planned range approach course (see local and squadron guidance). Altitude may
vary based on terrain, weather, and pilot low altitude category. Use 10 to 15 degrees nose low
maximum. The G and turn location will depend on the type of Pop-Up pattern to fly (offset or
parallel downwind). Be very careful while descending to pilot low-altitude minimums because it
is very easy to overshoot your altitude and fixate on the target or PUP. One technique is to level
off 200 to 300 feet high and ease the aircraft down to pilot low-altitude minimums during the
approach to the PUP. For pop-ups, gain as much energy as practical prior to the pull-up point. As
a ROT, plan on depleting approximately 15 knots to 30 knots of airspeed while executing the
pop-up attack.
15 25 VFS OI 07-A-10, 25 Jul 2011
5.3.4. The Pop. The actual pop-up is performed referencing the target and varies dependent upon
the ordnance employed. When on a controlled range, there are specific range references that aid
in identifying the pop-up point. These points should be memorized in order to reduce task load
on the range. GEOREFs or EGI ranges are the best method for determining the correct pull-up
point on a conventional range. With permission study, it is possible to plan an attack heading to
fly and identify GEOREFs such as roads, hills, and rivers. The pilot can also reference the
distance from the target in the HUD as a back-up if the coordinates are known for the target and
entered in the active steerpoint. The pop picture must be developed by flying a mechanical
approach course, pull-up and pull down. If the conditions are correct, a baseline sight picture can
be developed for use in a tactical environment. First learn the basics then apply the sight picture
discussion in the following paragraphs to sharpen pop delivery skills.
5.3.4.1. Pull-Up Point. Flying a mechanical pop-up using planned parameters will aid in
developing a sight picture to increase the chance for target acquisition and finding the wire. At
the planned PUP, select MAX power and begin a 3-G wings-level pull (G-suit inflates at 2.5 Gs)
to the desired climb angle. Pull up to 5 degrees higher than the planned delivery dive angle. PUP
distances assume the ground elevation is equal to the target elevation. Increase the PUP distance
by 0.1 NM for every 200 feet below planned altitude (For example, a 500-foot AGL run in could
be only 300 feet above target elevation. In this case, increase the pull up point by 0.1 NM).
5.3.4.2. Target Acquisition. After setting the planned climb angle, focus on acquiring the target.
The typical time to acquire the target from pull-up to pull-down is approximately 5 to 10 seconds
depending on run-in altitude. During the climb, the target will move down and aft in the quarter
panel. An important visual reference is the angle off the nose (AON) to the target at the pull-up
point and pull-down point. Knowing the pull-up/pull-down AONs helps focus the pilots eyes for
target acquisition. Calculate the AON using the following ROT: the pull-up AON is
approximately one-half the planned angle-off and the pull-down point AON is approximately
three-quarters of the planned angle off. For example, a 45-degree angle-off results in the target
starting at the 22 degrees AON at pull-up and moving to 32 degrees of AON at pull-down. These
are the areas that should be scanned during the climb to find the target. Do not confuse angle off
(AO) with angle off the nose (AON).
5.3.4.3. Correct PUP. The correct PUP for a strafe delivery is based upon desired delivery slant
range, desired dive angle, and specific range restrictions. As a ROT, pop-up for a low strafe or
rocket delivery approximately 1 mile prior to the intended release slant range. When the desired
PUP is reached, pull to approximately 5 to 10 degrees nose high and begin a roll and pull to the
target. For most conventional range strafe deliveries, the dive angle will be 5 to 10 degrees nose
low, assuming a 500-foot AGL run-in altitude.
5.3.4.4. Pull-Down Point. This is the point at which the pull-down is initiated. Normally, it will
be done with an unloaded roll followed by a 2- to 4-G pull down to intercept the planned attack
wire. Execute the pull-down as the aircraft approaches the correct pull-down visual reference. A
baseline sight picture for the pull-down point relates the target placement to a known cockpit
reference for bombing deliveries. This point is referred to as PTP (pull-down target placement).
16 25 VFS OI 07-A-10, 25 Jul 2011
5.3.4.5. PTP. The pull down point visual reference is determined using PTP. This is the angle
from the horizon to the target at the planned pull-down point. The IAA can be used as an
approximation of this angle. Since PTP is measured from the horizon it cannot be translated to a
sight picture without a known horizon reference. To calculate the PTP, add the IAA to the known
horizon reference and equate that distance to a canopy reference. The distance between the
center of two grommets (dust covers) is 5 degrees; a visual reference for canopy bow sight
picture measurements.
5.3.4.6. Techniques. This is a baseline starting point and is dependent on factors such as sitting
height and seat adjustment. Using the grommets (dust covers) for this sight picture affords the
pilot both right and left hand roll-in sight pictures. Pilots must determine their specific sight
picture from this starting point. Adjust the pull-down sight pictures for different IAAs as they
change and add the IAA to the horizon reference for the given climb angle. In a fluid tactical
environment with moving targets and inaccurate coordinates, using PTP references will aid
target acquisition while maneuvering to the correct wire.
5.3.6. Roll-In and Track References. The roll-in and track references discussed in the diving
delivery section above still apply.
5.3.6. Final. The final portion is the same as with any diving delivery. Use RTP cockpit
references to aid in establishing a proper aim-off distance for the base position flown. As the
pull-down is completed, the delivery considerations are those of a normal weapons delivery pass.
5.4. Bump-Up Pattern. The Bump-Up maneuver is primarily used to unmask for forward-firing
diving deliveries or level free-fall munitions employment. Like the Pop-Up pattern, it is an
unmask maneuver designed to achieve LOS with the target. When employing a bump-up attack
on the conventional range, crosswind, downwind, and base leg are identical to the rectangular
pattern. Normally, the downwind will be flown at 1,500 to 2,000 feet AGL, necessitating a
descent for the base leg. As in the Pop-Up pattern, the pilot should be cautious when descending
to pilot low-altitude minimums. Use 10 to 15 degrees nose low as a maximum descent rate.
5.4.5.1. Final. On final, the bump-up attack will be executed within ±15 degrees of the final run-
in heading. Instead of using large bank angles and positive G to get the aircraft from a nose-high
attitude to an attack position, the bump-up uses a slight climb to acquire the target followed by a
negative G pushover to intercept planned release altitude. A common error is to level off higher
than planned release altitude which may result in a CCIP consent delivery with a short time on
final. Because the target may be in sight while on a controlled range, this can be simulated by
pulling up approximately 5 degrees nose high, followed by a pushover to reacquire and track the
target. Remember, in the tactical environment the key is to acquire LOS with the target. A
shallow climb farther out may be preferred to a steeper climb close in.
6. Computed Free-Fall Munitions Employment.
6.1. Integrated Flight and Fire Control Computer. Bombing with IFFCC simplifies weapons
delivery significantly. IFFCC provides a CCIP based on the weapon selected in the current
DSMS profile that considers wind, aircraft velocity, AOA, altitude, and attitude. IFFCC provides
17 25 VFS OI 07-A-10, 25 Jul 2011
accurate weapons delivery even though the aircraft may be significantly off planned parameters;
however, weapons effects may be less than desired. Additionally, flying the aircraft through the
planned delivery requires using solid weapons delivery techniques and procedures to include
wind analysis.
6.2. Digital Stores Management System. All delivery specific information that IFFCC needs to
calculate the correct solution is contained in the profiles created during mission planning and
loaded to the DSMS via the DTC. This includes weapon type, delivery mode (CCIP, CCRP),
release mode (Single, Ripple Single), Fuzing (type and time), DTOF, minimum altitude and
desired safe escape maneuver. See Figure 7.10, DSMS Profile Page.
6.2.1. Delivery Modes. Free-fall bomb deliveries and rockets primarily use CCIP mode while
LGBs and IAMs use continuously computed release point (CCRP). It is imperative to know how
the CICU, DSMS, UFC and IFFCC all integrate and function prior to weapons employment.
(See Figure 7.2, IFFCC Air-to-Surface Cockpit Interface, Figure 7.11 IFFCC HUD
Symbology—CCIP).
18 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.10 DSMS Profile Page.
6.3. Altitude Sources. There are three altitude sources for IFFCC WD computations: Radar,
Baro, and Delta. The altitude source is selected on the armament HUD control panel (AHCP).
6.3.1. Radar Mode. Radar mode uses the radar altitude directly below the aircraft as the
height above target for WD computations. This mode is valid only over flat terrain and is
limited to altitudes 5,000 feet AGL and below.
6.3.2. Baro Mode. Baro mode computes a true MSL altitude by starting with the central air data
computer (CADC) barometric altitude adjusted by the Kohlsman altimeter setting (shown on the
cockpit altimeter) and adjusting it for lag, installation error, and nonstandard air temperatures.
The aircraft will take an automatic barometric reference point during takeoff. This function is
referred to as a “Baro update.” At approximately 50 to 60 KIAS, the IFFCC system records the
CADC barometric altitude from the cockpit altimeter. This is the starting point for all subsequent
19 25 VFS OI 07-A-10, 25 Jul 2011
calculations. From this point on, the Baro update consists of barometric data plus the bias
correction based on EGI GPS altitude, provided the EVE is less than 50 feet.
NOTE: Ensure this is accurate by dialing the cockpit altimeter until the HUD altitude reads
touchdown zone elevation prior to takeoff.
Figure 7.11 IFFCC HUD Symbology—CCIP.
6.3.3. Delta Mode. Delta mode, unlike the Baro mode, uses the CADC pressure altitude as a
starting point for computing true MSL altitude and calculates its own nonstandard pressure
correction (Delta) rather than relying on the altimeter setting. To calculate the nonstandard
pressure correction, Delta mode needs a reference altitude. Like Baro, an initial delta update is
accomplished during the takeoff roll and assumes that the cockpit altitude (altitude set in HUD)
is an accurate reading of true MSL altitude at that point. The rest of the process for correcting the
20 25 VFS OI 07-A-10, 25 Jul 2011
pressure/altitude scale is similar to the Baro mode. Remember that the CADC pressure altitude is
not effected by the altimeter setting, so changing the altimeter setting in flight does not affect
Delta mode altitudes. The main benefit of the Delta mode is that the reference altitude may be
changed via a delta update taken closer to the target area so that the corrections are more
accurate for the target air mass. Delta updates received from other A-10s or forecast values from
mission planning can be entered via IFFCC menus.
NOTE: If possible, an inflight Delta should be accomplished at the planned delivery altitude
near the target area.
NOTE: Delta mode is completely independent of the cockpit altimeter setting except for the
initial update on takeoff roll.
6.3.4. Selecting a Mode. Baro provides the most accurate method of WD when EVE is less than
50 feet. This is due to the constant Baro update which consists of barometric data plus the bias
correction based on EGI GPS altitude. If EVE is greater than 50 feet, then Delta provides the
most accurate method of WD. Radar mode may be the preferred mode over flat terrain when the
pilot is sure the terrain elevation below the aircraft at release is the same as the target elevation
and release occurs below 5,000 feet AGL.
6.4. Elevation Sources. IFFCC provides the ability to select from several different elevation
sources through its digital terrain system application software (DTSAS). IFFCC incorporates
Level 1 digital terrain elevation data (DTED) which is loaded into the data transfer cartridge
(DTC). IFFCC provides hot elevation, passive ranging, look-aside ranging, and coordinate
ranging.
Figure 7.12 Delta CAL Submenu.
21 25 VFS OI 07-A-10, 25 Jul 2011
6.4.1. Hot Elevation. In this mode the pilot manually enters a known target elevation into either
the HUD via the UFC or the CDU, which will then transfer the elevation to the HUD. IFFCC
will use this as the only elevation for solution computations.
6.4.2. Passive Ranging (Data Transfer System [DTS]). IFFCC calculates the elevation for the
point on the ground overlaid by the gun and bomb or rocket sights simultaneously. IFFCC then
uses the calculated elevation for solution computation. This only occurs if DTSAS is on and the
pilot selects auto-elevation mode by using the UFC Data and Select switches, or by selecting
auto-elevation mode (referred to as “DTS” by many pilots) as a preference when loading the
DTC. When active, the elevation in the HUD is replaced with “DTS.”
6.4.3. Look-Aside Ranging. IFFCC calculates the elevation for the point on the ground overlaid
by the Maverick reticle or the depressible pipper. This mode is only active in auto-elevation
mode (“DTS” visible in HUD).
6.4.4. Coordinate Ranging (CR). To bomb on CR, use HOT elevation and ensure the current
steerpoint while delivering weapons is the target. When enabled in the CDU, CR automatically
returns an elevation when the pilot enters coordinates into a Waypoint on the CDU. If auto-
elevation mode is inactive (numeric elevation visible in the HUD), and the Waypoint under
modification is the active steerpoint in the HUD, the elevation returned by CR will automatically
transfer to the HUD.
6.4.5. Targeting Pod Elevation. When targeting pod (TGP) is initially selected, the HUD
will display „T DTS‟ indicating TGP is selected, but DTS will be used until the laser is actually
fired. After firing the laser, the HUD will display „T XXXX‟ with X representing the elevation
provided by the targeting pod. The IFFCC only accepts the last laser ranging information
received from the pod. If the TGP laser is set to latched mode, the IFFCC elevation will
continuously update as long as the laser is firing. For example, if the TGP LOS has moved to an
area with a significantly different elevation and the laser has not been fired, then IFFCC will use
the potentially incorrect elevation from the last time the laser was fired. Every time the laser has
stopped firing, the “T XXXX” will flash in the HUD to indicate the new elevation has been
accepted.
NOTE: If in CCRP mode and using the TGP as an elevation source, the TGP elevation will be
used by IFFCC, as opposed to the SPI elevation. If the IFFCC elevation source is set to DTS or
HOT elevation, then the SPI elevation will be used.
6.4.6. Selecting the Best Elevation Source. Use auto-elevation mode (DTS) in most cases. On
conventional (known target set) ranges, use HOT. If no elevation is known (pop up target) and
DTS is not functioning, then use TGP laser elevation.
6.5. Computed Free-Fall Sight Application.
6.5.1. Profile. In order for the IFFCC system to compute accurate release displays, the correct
DSMS weapon profile must be selected, delivery parameter data must have been input correctly
22 25 VFS OI 07-A-10, 25 Jul 2011
on the ground, and appropriately selected on downwind. Several techniques exist to ensure that
all necessary data have been input accurately.
6.5.1.1. Base to Roll-In (Pull). Perform the roll-in and Conventional Pattern, and IAW Pop-Up
Pattern.
6.5.1.2. Roll out (Center). Since the center of the pitch ladders show the aircraft‟s path over the
ground in computed HUD modes, centering the pitch ladders over the target result in a smooth
PBIL track through the target. The PBIL guides to the desired release point by predicting the
future position of the bomb along the ground. Begin roll-out as the pitch ladders approach the
target. Since the pitch ladders are wind corrected this will aid in leading a roll out that positions
the aircraft upwind of the release aim point.
6.5.1.3. Track (Set). After roll out, fix any PBIL errors with aggressive corrections while setting
track. The DRC and MRS are displayed on the PBIL to show how the desired time of fall and
abort cue relate to the current aircraft position. “Set” the DRC. Remember at track that ITP is
only an indication of aircraft position, not a track reference.
6.5.1.4. Final. Once track is set, check the parameters and decide if they are within those required
for the delivery. Keep the PBIL on the release aim point and allow the pipper to track to it. As
the pipper reaches the aimpoint, depress the weapon release button and hold it long enough for
the aircraft to release the number of weapons selected. The reticle will flash when enough time
has elapsed for all of the weapons to release. After pickling, perform the appropriate SEM.
6.5.2. Solution Options. There are limitations to when a solution can be displayed in the HUD.
The HUD projection is round, not square. This creates a problem with high crosswind and
deliveries with high mil depressions. The HUD can only display a pipper within a 170-mil radius
of the 140-mil HUD center. Therefore, the center of the HUD, defined at 140 mils of depression,
is the area capable of displaying the maximum amount of crosswind solution (170 mils).
Likewise, the greatest depression available is 310 mils, with no crosswind capability at that
depression. HD munitions are very susceptible to this problem. (See Figure 7.13, Head-Up
Display Field of View Limits/MK 82 AIR.) This figure is based on a 4.5-mil per knot crosswind
correction (found in the delivery parameters in the Battle Book). A delivery requiring 285 mils
can display a solid PBIL out to 20 knots of crosswind (assuming the 4.5 mil/kt correction).
IFFCC provides two options for WD solutions: Manual Release and Consent to Release. These
depend on which mode is selected in the weapons submenu (or on IFFCC preferences in
A/W/E).
6.5.2.1. Manual Release. This option allows the solution to be displayed only if the solution is
within the HUD field of view (FOV). When the computed solution is outside the HUD field of
view, the PBIL is dashed. In this case, when the pilot depresses the weapons release button,
weapons will release IAW the profile, and the pilot cannot accurately deliver weapons.
6.5.2.2. CCIP Consent Release (5 mil & 3/9). The CCIP Consent Release function provides a
CCIP weapons release capability when the CCIP solution is outside the HUD FOV but above
550mils (in level flight).
23 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.13 Head-Up Display Field of View Limits/MK 82 AIR.
6.5.2.2.1. When the CCIP solution is outside the HUD FOV the reticle is clamped to the outer
edge of the HUD (with the clamped pipper 153 mils from HUD center regardless of bank angle).
The PBIL and CCIP reticle are dashed, the analog range bar is removed, and a predesignate time-
to-release numeric (TTRN) is displayed inside the dashed reticle if the time to weapons release is
less than 20 seconds. (See Figure 7.14, Predesignate CCIP Consent Release Symbology.) The
predesignate TTRN is displayed in increments from 0.1 to 9.9 seconds, then 10 to 20 seconds.
24 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.14 Predesignate CCIP Consent Release Symbology.
NOTE: When the solution is within the HUD FOV the solution and symbology will behave
according to „Manual Release‟ regardless of IFFCC consent setting.
6.5.2.2.2. To employ the CCIP consent release function, the clamped CCIP pipper is used as the
aiming reference to designate the intended target. The pilot rolls in and places the CCIP pipper
over the target, and then depresses and holds the Weapons Release button to enter the CCIP
Consent Release function. This causes the PBIL and CCIP bomb reticle to become solid, and the
CCIP consent symbology to be displayed (Figure 7.15, Postdesignate CCIP Consent Release
Symbology). The symbology consists of a steering line, a 10-mil diameter solution cue, and the
TTRN, in whole seconds.
25 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.15 Postdesignate CCIP Consent Release Symbology.
6.5.2.2.2.1. After designation, the aircraft is flown to align the CCIP pipper with the solution cue.
• If “5 MIL” was selected from the MAIN MENU, IFFCC commands release when the CCIP
pipper is within 5 mils and passes the 3/9 line of the solution cue, parallel to HUD Horizontal
Plane (Figure 7.16, CCIP Consent Release Symbology at Release). If the CCIP pipper passes
outside of 5 mils, then the release will not be commanded. (Figure 7.18, Azimuth Error Consent
Release Inhibit.)
26 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.16 CCIP Consent Release Symbology at Release.
• If 3/9 was selected from the “MAIN MENU”, IFFCC commands release when the CCIP pipper
crosses the 3/9 line of the solution cue, parallel to HUD Horizontal Plane), regardless of
horizontal range to the solution. (See Figure 7.17, CCIP Postdesignate 3/9 Delivery.)
• The solution will become invalid prior to IFFCC commanded release (and hence aborted) if the
Weapons Release button is released prior to actual weapon release, or if there is a fault in the
consent system.
NOTE: Rockets are always manual release regardless of IFFCC Consent setting.
NOTE: LGBs/CBU-97 are always 3/9 regardless of IFFCC Consent setting.
27 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.17 CCIP Postdesignate 3/9 Delivery.
6.5.3. Abort Cues. IFFCC calculates and displays an abort cue based on pilot and aircraft data.
6.5.3.1. Real-Time Safe Escape. For free-fall weapons, IFFCC can calculate a minimum TOF for
safe escape based on actual aircraft parameters and planned escape maneuver. IFFCC calculates
safe escape for fuze, frag or Min Alt and displays the MRS and MRC based on the higher of the
three.
6.5.3.2. Selecting NONE. If this SEM is selected in the weapon profile, IFFCC will remove
fragmentation as a consideration for the MRS on GP bombs. Selecting NONE in the CBU-
87/CBU-89/CBU-97 submenus has a slightly different effect on the MRS and MRC than in the
MK 82/MK 84 submenus, as explained below:
• MK 82/MK 84: MRS and MRC does not consider frag and is only based on the values the pilot
enters for Min Alt and Fuze. No consideration is given to safe escape/safe separation.
28 25 VFS OI 07-A-10, 25 Jul 2011
• CBU-87/CBU-89/CBU-97: MRS and MRC represent submunition arming while not
considering frag for an intact canister. Only fuzing and function will be considered, not safe
escape/safe separation.
Figure 7.18 Azimuth Error Consent Release Inhibit.
6.5.3.3. Real-Time Safe Escape Cues. If actual flight parameters are outside the boundaries of
these tables, IFFCC extrapolates from the tables to calculate a RTSE value. To alert the pilot that
IFFCC is extrapolating outside the bounds of RTSE tables, the MRS and MRC will flash. The
29 25 VFS OI 07-A-10, 25 Jul 2011
flashing cues are somewhat subtle and are not always obvious on a cluttered HUD. Flashing
MRS/MRC should have no affect on the delivery.
6.5.3.4. MRS/MRC with MAN REL. IFFCC uses the inputs minimum altitude, fuze time, and
safe escape maneuver to calculate a real time abort cue. IFFCC displays this cue as the MRS and
MRC. The MRS is displayed along the PBIL. The MRC is displayed as a caret on the inside of
the reticle. The MRC position inside the reticle corresponds to the minimum release slant range
for the highest of fuze, frag, or ground. The minimum release point is reached when the analog
range bar meets the caret. This will occur at the same time that the MRS meets the pipper.
IFFCC displays an “X” over the pipper if this situation exists and the pilot should abort the pass.
If the range bar has not met the caret or the staple is above the pipper when the bomb is released,
then the aircraft is outside the minimum slant range computed by IFFCC.
6.5.3.4.1. Valid Solution Indications. When in Manual Release mode, the valid solution indicator
(VSI) appears as a small “x” over either the MRS or the DRC when the IFFCC computer
determines (with the present aircraft parameters, namely airspeed, dive angle, and winds) a
solution will not be available within the HUD FOV prior to passing the respective TOF. This
occurs only when no consent option is selected or available. For high sight depression
parameters, the VSI may appear at roll-out but go away as the aircraft accelerates on final. If the
VSI is present, make a decision based on wind information and accuracy of parameters to
determine whether to continue the pass or abort.
6.5.3.5. MRS/MRC with CCIP Consent. When employing in CCIP Consent Release modes, the
MRS is based upon the true CCIP solution, which is outside the HUD FOV.
7. Weapon Employment
7.1. Rocket Employment.
7.1. Conventional Rocket. This delivery is characterized by short slant ranges and generally
steeper dive angles (30 degrees or more). Because of the shorter slant range, conventional
rockets are more accurate than standoff, tactical, and loft rockets. However, this accuracy is
achieved at the expense of threat standoff.
7.1.1. CCIP Rockets. IFFCC CCIP significantly reduces the difficulty in shooting accurate
rockets. With a rocket profile selected, the PBIL, MRS, DRC, and MRC are removed from the
normal CCIP display. The rocket reticle is not displayed in the HUD unless a solution is
available. Slant range, the critical element in shooting rockets, is constantly computed out to the
kinematic range of the rocket. This information is displayed by the analog ranging bar inside the
reticle, and below the reticle in NM when the slant range exceeds 12,000 feet. In this case, the
analog range bar will be locked at the 12 o‟clock position. On roll-in, place the pipper short of
the target, generally a half reticle short. Trim the aircraft to maintain correct G-loading and allow
the pipper to track to the target. Avoid the tendency to hold the pipper on the target as this will
induce tip off. (See Figure 7.19, CCIP Rocket Reticle.)
30 25 VFS OI 07-A-10, 25 Jul 2011
7.1.2. Manual Rockets. Manual rocket deliveries are similar to manual bomb deliveries. Use a
depressible pipper with either STBY Pipper, HARS, or Guns. Wind corrections are not as large
as for bombs. Linear offset or mil crank may be used to adjust RAP/RAPE for winds. As a rule,
headwind and tailwind corrections are negligible at closer slant ranges (less than 12,000 feet) and
only the crosswind need be considered if a “close” mark is required).
7.1.2.1 Tactical Sight Setting. The tactical sight setting is a manual delivery technique using a set
mil reference to employ manual rockets at several slant ranges. Additionally, it can be used if
wind velocity is not known and/or if there is no time to calculate wind corrections to achieve
specific delivery parameters. With the depressible pipper set to 102 mils and dive angles between
5 to 15 degrees, the top of the reticle should be used as the aiming reference for 9K S/R, the
pipper for 12K S/R and the bottom of the reticle for 15K S/R shots (it can also be set to 90 mils
for a 6/9/12K reference). Crosswind correction must still be applied for accurate delivery
(approximately 0.5 mils per knot). This sight setting can also be used with the standby pipper;
however, realize that standby pipper is 50 mils in diameter vice 25 mils for the depressible
pipper. (See Figure 7.20, Tactical Sight Setting, for additional information.)
Figure 7.19 CCIP Rocket Reticle.
7.1.3. CCRP Rockets. CCRP is a system delivery that will usually be employed at low-altitude to
„loft‟ rockets or medium-altitude for level or shallow deliveries. The RAN replaces the TTRN
31 25 VFS OI 07-A-10, 25 Jul 2011
and displays a “45” numeric seven seconds prior to the target being in range. During a low
altitude run-in, the pilot may perform a 10-, 20-, or 30-degree loft. Start the pull-up when the
RAN equals 10 degrees plus the planned loft angle. For example, for a 20-degree loft, the pilot
starts a pull-up to 20 degrees when the RAN equals 30. During the loft profile, the pilot uses the
same CCRP references discussed previously by applying sufficient G to place the PBRL on the
ASL. MAN REL is the only release mode for rocket deliveries; therefore, the pickle button is
“hot” and the pilot must attempt to release the rockets as close to the center of the Solution Cue
as possible. Remember, this solution is always calculated based on the SPI.
7.1.4. Illumination Rockets. The Mk-257/278 rockets are illumination rockets. These rockets
provide approximately 2 to 3 minutes of illumination. Delivery parameters can vary from lofting
nose high to 30 degrees nose low. Illum rocket solutions target a point over the SPI. The
delivery of M257/278 rockets is restricted to CCRP mode. The “USE CCRP” message will be
displayed in the HUD.
Figure 7.20 Tactical Sight Setting.
7.1.4.1. The MRC and analog range bar are utilized in a unique way with M257/278 rocket
flares. The analog range bar represents the predicted flare ignition height while the MRC
represents the desired flare ignition height to mid-burn. For the rocket flare to attain the menu-
entered desired flare height at mid-burn, vertically maneuver the aircraft to place the analog
range bar on the MRC.
7.1.4.2. If the MRC is inside the analog range bar (Figure 7.21, Rocket Continuously Computed
Release Point Analog Range Bar), push the nose of the aircraft down to position the analog range
bar over the MRC. If the MRC is outside the analog range bar, pull the nose of the aircraft up to
32 25 VFS OI 07-A-10, 25 Jul 2011
position the analog range bar over the MRC. In other words, fly the MRC to the analog range
bar.
7.1.4.3. Once the analog range bar and MRC are coincident, maintain that flight path angle until
release.
7.1.4.4. If launching the selected rocket flare would cause it to hit the ground before parachute
deployment, the PBRL, ASL, Solution Cue, TTRN, analog range bar and MRC will be removed
from the HUD and a dashed “X” will be displayed over the pipper.
CAUTION: The HUD symbology for the rocket CCIP is very similar to the gun CCIP. RKT is
displayed below the rocket reticle to help distinguish the two. Take care to ensure the proper
symbology is being used for the two respective weapons as dangerous miss distances can occur
when using opposing symbology.
Figure 7.21 Rocket Continuously Computed Release Point Analog Range Bar.
33 25 VFS OI 07-A-10, 25 Jul 2011
7.2 Gun Employment. The GAU-8/A is the primary weapon of the A-10. With over 1,150
rounds of 30mm high explosive incendiary (HEI) and armor piercing incendiary (API) rounds,
combined with a sustained rate of fire of 62 rounds per second, the A-10 pilot is provided
unsurpassed staying power and flexibility. The GAU-8/A characteristics of increased standoff,
high accuracy, and sustained firepower make strafe the most reliable and effective method for
the A-10 to deliver firepower against a ground target. Pilot knowledge of proper strafe
techniques and the ability to recognize, analyze, and correct for common pilot errors are critical
for employment.
7.2.1. Gun Characteristics.
7.2.1.1 Clearing Cycle. The GAU-8/A goes through a barrel clearing cycle within 0.5 seconds
after every firing. The goal, when designing the gun, was to have no unfired or “wasted” rounds
in the barrel. Additionally, the gun can detect a broken firing pin (resulting in a live round). The
cockpit gun unsafe light will illuminate if the clearing cycle is not completed in 2.5 seconds. If
two broken firing pins are detected, a gun unsafe indication will result. If the clearing cycle is
interrupted by safing the gun, a gun unsafe indication will result.
7.2.1.2 Cooling Cycle. The cooling cycle was designed to eliminate increased bullet dispersion
due to barrel heating and rotates the barrels under a schedule following trigger release. To cool
the barrel, the GAU-8/A will automatically cycle at 24, 60, 100, and 150 seconds after firing.
The cycle can be interrupted at any point by squeezing the trigger. Barrel cooling also stops
when the master arm or rotate switch is set to the safe position.
7.2.1.3. Dispersion. The GAU-8/A was built with the specifications that 80 percent of the bullets
must fall within a 5-mil diameter of the desired aimpoint and 100 percent must fall within 13
mils. Dispersion, however, does increase as the gun heats up. After six to eight passes of 150
rounds each with only 1.5 minutes between bursts, gun dispersion can increase to 30 mils for 100
percent and 18 to 20 mils for 80 percent of rounds fired. Dive angle does not affect dispersion,
only the bullet footprint.
7.2.1.4. Harmonization. The GAU-8/A is installed such that bullets pass through the 41-mil
depression at 4,000 feet slant range when in 30 degrees of dive with a 36,000-pound aircraft.
7.2.1.5. Rounds Counter. Rounds remaining are displayed in increments of 10 on the
DSMS page, and in the HUD when in GUNS mode. It is set in IFFCC by the weapons load
crew when the gun is loaded.
7.2.2. Parameters. Strafe deliveries for the A-10 are divided into two broad categories: high-
angle and low-angle. Low-angle strafe (LAS) and long range strafe (LRS) are generally
considered any delivery 15 degrees and below, and HAS is usually 30 degrees and above. Two
target strafe (TTS) can be accomplished from either LRS or HAS deliveries. Each specific
delivery has its advantages and disadvantages. In general, strafe parameters are dictated by the
target, the threat, and the weather.
34 25 VFS OI 07-A-10, 25 Jul 2011
7.2.2.1. Low-Angle Strafe. The objective of a LAS delivery is to press into effective kill range
for a hard target (tank). Cease fire on a LAS delivery on soft targets at 2,000 feet and 3,000 feet
on hard targets. When employing manually and assuming firing at 2,000 to 2,500 feet slant
range, the aiming reference is 39 to 40 mils. (See Figure 7.22 Manual Low-Angle Strafe Aiming
Reference.) For LAS passes against hard targets, cease fire no later than 3,000-foot slant range to
avoid breaking the 3/9 plane of any target shot at. If an aircraft breaks the 3/9 plane of a hard
target after employing on it, the aircraft will likely sustain frag/ricochet damage.
Figure 7.22 Manual Low-Angle Strafe Aiming Reference.
7.2.2.2. Long-Range Strafe. The objective of a LRS delivery is to standoff using the excellent
range of the GAU-8/A to kill or immobilize a target. Realize that if attacking a heavily armored
target, the probability of damage (Pd) goes down significantly as the range increases. However, a
mobility kill (M-Kill) may still be likely. Refer to the weapons shop and AFTTP 3-1.A10 for
specific Pd against targets. If attacking personnel, lightly armored targets (e.g., APCs), or soft
skinned vehicles (e.g., trucks and jeeps), this can be an effective delivery. LRS slant range, when
employing on a controlled range, is typically 5,000 to 6,000 feet. (See Figure 7.23, Manual Long
Range Strafe Aiming Reference, for gun cross elevation with the target at 5,000 to 6,000 feet
slant range.) If employing manually, elevate the gun cross to compensate for gravity drop based
on slant range. For low-altitude shots, slant range will very nearly equal ground range.
35 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.23 Manual Long Range Strafe Aiming Reference.
7.2.2. 3. High-Angle Strafe. HAS deliveries are less sensitive to elevation and slant range errors
than low angle deliveries. Because of the increased dive angle, there is increased bullet density,
more vulnerable parts of the target are exposed, and the overall effective target area is increased.
HAS deliveries are used from medium-altitude with dive angles greater than 20 degrees. Avoid
the 15- to 30-degree dive region for hard targets due to limited weapons effects (obliquity angles
may result in ricochet at impact versus penetration). Just as in LRS, the slant range is dependent
upon desired weapons effects and target attacked. If employing manually, specific dive angle,
altitude, and airspeed parameters must be met to hit the target. Similarly, the gun cross will have
to be elevated to compensate for gravity drop at various slant ranges. Reference squadron Battle
Books for specific deliveries and their mil elevations. The correct slant range is acquired when
employing on a conventional range and firing at the desired altitude, while on the planned dive
angle. (See Figure 7.24, Slant Range Estimation Prior to Roll-In, to see how to compute slant
range by referencing the target on the canopy rail.)
7.2.2.4 Two-Target Strafe. TTS is shooting two targets with two separate bursts on the same
pass. When employed in a low-angle delivery, “think” of it as a combination of LRS and LAS—
incorporating the techniques of both. When employing on a controlled range, strafe the nearest
target to the range tower first, then move away from the tower to strafe the second target.
Tactically, strafe in the direction of egress (left to right off right, for example). As a ROT, targets
should be close enough that they are in the confines of the HUD simultaneously when opening
fire on the first target. Shoot long then short if the targets are aligned with the run in axis to avoid
breaking 3/9 with a target.
36 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.24 Slant Range Estimation Prior to Roll-In.
7.2.3. Strafe Symbology.
7.2.3.1. Guns Attack Modes. Air-to-surface guns can be accomplished in GUNS and CCIP
modes. GUNS mode offers CCIP reticle, CCIP guns cross, 4/8/12 reticle, and wind corrected
4,000 foot gun cross. If a fixed sight (wind corrected fixed gun cross or 4/8/12 reticle) is selected
in guns, then in CCIP the 4K wind corrected gun cross will be displayed (when the gun is
armed). In HARS with the GUN ARMed, a fixed, non-wind corrected 4K GUN CROSS is
displayed. No gun cross is available in STANDBY PIPPER.
7.2.3.2. CCIP Gun Reticle. The power-on default sight for the gun is the CCIP gun reticle. The
CCIP is corrected for all factors influencing the bullets after the gun has reached full speed
(approximately 0.5 second). Some of these factors include deceleration, gravity drop, aircraft
angle of attack, gun barrel rotation, and winds. The gun reticle consists of a 1 mil pipper at the
center of a 50-mil circular reticle with range marks at the 12, 3, 6, and 9 o‟clock positions. (See
Figure 7.25, Continuously Computed Impact Point Gun Reticle and Gun Cross.)
37 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.25 Continuously Computed Impact Point Gun Reticle and Gun Cross.
7.2.3.2.1. Analog Range Bar. An analog range bar with a 5-mil tab indicates the slant range to
the CCIP gun solution in thousands of feet. (See Figure 7.26, Analog Range Bar and Range
Numeric.) The analog range bar is located just inside the reticle and moves counter clockwise
from the 12 o‟clock position as slant range to the target decreases. A hash mark at the end of the
analog range bar indicates current slant range in thousands of feet as read from the reticle clock
position. For example, with the hash mark at the 6 o‟clock position, current slant range is 6,000
feet. Slant ranges can be displayed from 0 to 12,000 feet. Outside of 12,000 feet, the range bar
remains fixed at the 12 o‟clock position and an accurate range numeric is presented as long as a
valid solution exists. The 2-digit numeric displays the range in nautical miles beginning at 0.1
and increasing in 0.1 increments to 9.9. The numeric then changes to an integer beginning at 10
and increasing to 99. A pilot option is to display the range numeric in kilometers. In this case, a
“K” will follow the range numeric, and the maximum range that will be displayed is 99K.
Maximum ranges in excess of 6 NM were observed during flight tests of IFFCC. If there is no
solution, the range numeric is removed, the analog range bar is thin, and an X is placed over the
pipper. If the pipper is pointed at a target that exceeds the maximum range that IFFCC can
calculate, the pipper will clamp at the maximum range solution (with an “X” over it) and will
still be roll stabilized and wind-corrected. This aids the pilot in keeping the pipper near the target
for when a solution becomes possible.
38 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.26 Analog Range Bar and Range Numeric.
7.2.3.2.2. CCIP Gun Reticle MTI. The CCIP gun reticle includes two moving target indicators
(MTI). (See Figure 7.27 Continuously Computed Impact Point Gun Reticle Moving Target
Indicator.) The two vertical, 5-mil lines to the left and right of the pipper can be used to estimate
the lead required for a moving target. These lines expand or contract as the slant range and bullet
TOF is changed. The MTI assumes the target is moving perpendicular to the aircraft at a rate of
20 knots. By placing the target under the MTI with the gun pipper in front of the direction of
motion, the target and bullets should arrive at the same point at the same time. Use the MTI to
estimate movement and deliver a burst of sufficient length and dispersion to increase the
probability of a hit.
7.2.3.3. CCIP Gun Cross. (See Figure 7.25 Continuously Computed Impact Point Gun Reticle
and Gun Cross.) The IFFCC CCIP gun cross displays the same computed impact point as the
CCIP gun reticle, using more compact symbology. The MRC functions identically to the reticle
MRC. The gun cross consists of a 2-mil pipper and a 4-mil gap, and each line segment of the
cross is 5 mils long making the cross a total of 20 mils across. The horizontal line at the top of
the cross helps to distinguish it from a non-computed gun sight. The horizontal bar will not be
present, no range numeric will be shown, and the cross will have an X through it if a solution is
not available due to lack of altitude source or a solution outside of the HUD FOV, similar to the
CCIP gun reticle.
39 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.25 Continuously Computed Impact Point Gun Reticle and Gun Cross.
7.2.3.4. Minimum Range Symbology for Guns. A minimum range caret (MRC) is available in
Guns and CCIP modes for the CCIP reticle and gun cross. This gun MRC defines a minimum
recovery altitude that is calculated using the minimum altitude entered in the IFFCC 30 MM
submenu. This caret also provides a time-to-go indication before aircraft recovery from guns
pass must begin (four Gs in 2 seconds WINGS LEVEL is the assumed recovery). (See Figure
7.26, Minimum Range Cue.) If the min alt is set to what is in the Battle Book, then the recover
MUST be a 4G WINGS LEVEL pull to the horizon to recover at or above the min alt. Reference
the squadron battle book for „pads‟ to add to the min alt setting to allow for a typical „climbing
safe escape‟-like maneuver that allows up to 30 degrees of bank during the 4G pull to the
horizon.
• The caret is clamped vertically next to the top of the 12 o‟clock tick when there are 5 seconds
or more until recovery must begin. The caret begins descending vertically when the time-to-go to
the minimum recovery altitude (at current rate and angle of descent) decreases below 5 seconds.
• When the aircraft is less than 5 seconds above the minimum recovery altitude (at current rate
and angle of descent), the caret will be displayed below the top of the 12 o‟clock tick and above
the 3 o‟clock tick.
• When the aircraft is at the minimum recovery altitude, the caret will be next to the 3 o‟clock
tick.
• When the aircraft is less than 5 seconds past (or below) the minimum recovery altitude (at
current rate and angle of descent), the caret will be displayed below the 3 o‟clock tick and above
the bottom of the 6 o‟clock tick.
• The caret will be clamped at the 6 o‟clock tick when the aircraft is 5 seconds or more below the
minimum recovery altitude.
40 25 VFS OI 07-A-10, 25 Jul 2011
• Setting the minimum altitude in the 30 MM submenu to 0 feet deselects the gun CCIP
minimum range cue display.
Figure 7.26 Minimum Range Cue.
7.2.3.5. 4/8/12 Gun Reticle. Toggling the SEL rocker on the UFC or cycling DMS L/R with
HUD-SOI will display the 4/8/12 gun reticle. IFFCC corrects for crosswinds and the pilot
elevates the sights for slant range. The 4/8/12 gun reticle displays three wind-corrected fixed-
range pippers representing 4,000, 8,000, and 12,000 feet slant range solutions; the analog range
bar is not present. (See Figure 7.27, 4/8/12 Gun Reticle and 4,000 Foot Wind-Corrected Gun
Cross, for more information.)
7.2.3.6. Wind Corrected Gun Cross. The wind-corrected gun sight (WCGS) is similar in
appearance to the CCIP gun cross, except it has no horizontal bar at the top and no range
numeric. The WCGS is a cross set at 41 mils. Elevation of the gun sight for targets inside or
41 25 VFS OI 07-A-10, 25 Jul 2011
beyond 4,000 feet slant range have to be estimated by the pilot. Like the 4/8/12 gun reticle, this
sight is useful when target elevation information is unavailable.
Figure 7.27 4/8/12 Gun Reticle and 4,000 Foot Wind-Corrected Gun Cross
7.2.4. Manual Strafe Deliveries. When employing the GAU-8/A manually, elevate the sight for
slant range and correct upwind for crosswind.
7.2.4.1. Sight Settings. There are several sight settings for GAU-8/A manual strafe deliveries:
Standby Pipper, HARS fixed gun cross, Wind Corrected 4k Gun Cross, and the 4/8/12 Reticle.
When using the standby pipper, set the appropriate mils for the estimated slant range while
offsetting for estimated winds.
42 25 VFS OI 07-A-10, 25 Jul 2011
7.2.4.2. Elevate for Slant Range. Elevate the sight for the estimated slant range while offsetting
for estimated winds. When using the wind corrected 4K gun cross, only elevate for slant range.
See the Battle Book for elevation techniques based on delivery (4/6/9K strafe) and sight settings
for HAS. When using the 4/8/12 reticle, there are three pippers inside one reticle to aid
estimating elevation. The top pipper of the 3 is the 4K pipper and is fixed at 41 mils.
7.2.4.3. Wind Corrections. Strafe wind correction presents a similar problem to that encountered
in the delivery of any other type of conventional ordnance. Elevate the gun cross for a headwind
and depress for a tailwind. For crosswinds, there are two basic methods to correct for wind once
on final: drift/crab or bank.
7.2.4.3.1. The drift method involves using an upwind roll-in point and AOP. Once rolled out on
final, the wind will “drift” the aircraft into its firing position. The same effect can be achieved
utilizing the crab method into the wind. Realize that the release aimpoint in both cases will be the
same. Neither drift nor crab has an advantage over the bank method other than firing with wings-
level. For direct crosswinds, the standard correction factors are: 0.5.mil per knot of crosswind for
most slant ranges or 1-foot per knot of crosswind for every 2,000 feet of slant range. For
example, for a 15-knot crosswind at 4,000 feet slant range, place the gun cross 7.5 mils or 30 feet
upwind of the target and fire. (See Figure 7.28, Manual Strafe Techniques, for more
information.)
7.2.4.3.2. Figure 7.29, Velocity Vector and Crab and Drift Aimpoints, illustrates a technique
using a gun cross to TVV ratio against crosswinds to determine the aimpoint when employing
with the OPT-C gun cross. As a ROT, use 1:6 ratio against armor (up to 4,000 foot slant range),
use 1:4 ratio for long-range strafe (4,000 to 10,000 feet), and use 1:2 ratio for very long-range
strafe (slant range greater than 10,000 feet). Mil dispersion will compensate for these ROTs. For
example, a 4,000 foot slant range requires the pilot to place the target one sixth the distance from
the gun cross towards the TVV.
43 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.28 Manual Strafe Techniques, for more information.
44 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.29 Velocity Vector and Crab and Drift Aimpoints.
7.2.4.3.3. In a strong crosswind, a drifting or crabbing attack will require a considerable offset
aimpoint. Avoid using the rudder, uncoordinated flight will cause a lateral trajectory shift error.
(See Figure 7.30, Trajectory Shift Error.) Due to bullet velocity and low trajectory angles,
headwind and tailwind corrections are minimal in low-angle and long-range strafe (unless they
are very strong). High-angle strafe corrections, using the drift or crab method, are the same as for
low-angle deliveries. However, during high-angle strafe, headwinds and tailwinds are much
more of a factor both for the ground track and the AOP. A ROT for 30 degrees or greater is to
use 0.5 mil for every knot of direct headwind or tailwind.
7.2.4.3.4 For LAS/LRS using the bank strafe method, the aircraft drift is countered by banking
into the wind. Keep the no crosswind aiming reference for the slant range to be used on the target
with bank, and shoot at the appropriate slant range. Since the wind drift has been canceled by
bank, the aircraft is flying straight at the target and is pointed at the target. It is similar to flying a
wing low approach to the runway. Banked strafe is only valid for crosswinds up to 15 knots
and/or slant ranges up to 8,000 feet. (See Figure 7.28, Manual Strafe Techniques, for further
information.)
45 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.30 Trajectory Shift Error.
7.2.4.3.5. Mil Sizing a Target. Because a mil in the HUD is a fixed size, it is possible to estimate
the range to a target if the size of the target is known. A standard conventional range strafe rag is
16 feet. The standard chassis of most former Soviet Union equipment (e.g., tank, APC, or self-
propelled gun) is approximately 20 feet in length, 10 feet in width, and 10 feet in height. The mil
size of a target is simple. See the formula below. This leads to the slant range per mil relationship
presented in Figure 7.31, Slant Range/Milliradian Relationship, and must be determined for both
head/tail and beam aspects. The aspect must be determined prior to release, and mil relationship
used to determine slant range and appropriate aimpoint (i.e., for the standard Soviet tank and
4,000 feet slant range, it would be 5 mils on the beam and 2.5 mils head/tail).
46 25 VFS OI 07-A-10, 25 Jul 2011
Figure 7.31 Slant Range/Milliradian Relationship.
7.2.4.4. Common Strafe Errors. These include aimpoint and tracking error, slant range estimation
error, and uncoordinated flight error.
47 25 VFS OI 07-A-10, 25 Jul 2011
7.2.4.4.1. Aimpoint and Tracking Error. The most common pilot-delivery error in strafe is the
failure to place and maintain the aiming reference on the target and not obeying the cardinal rule
of track-shoot-track. This error is applicable for both fixed gun sight and computed gunnery.
7.2.4.4.2. Slant Range Estimation Error. The second most prevalent error with non-computed
gunnery is firing at the incorrect slant range for the given mil setting. The reverse of this is
equally true—using the wrong mil setting at a known slant range. Pilots must know the mil
depressions necessary to hit a target at various slant ranges.
7.2.4.4.3. Uncoordinated Flight. This could be caused by a rudder input or by the rudder being
incorrectly trimmed (e.g., needle/ball not centered). When stepping on the left rudder, the nose
(and aiming reference) will swing left, but the flight path of the aircraft will not change
immediately. The bullets will hit between the aiming reference and the flight path. The exact
impact point depends on airspeed and bullet velocity, but in the A-10 it is approximately one-
sixth of the way from the gun cross to the velocity vector.
7.2.4.5 Shooting Combat Mix (CM). HEI has a lighter, faster muzzle velocity initially but due to
higher drag, does not carry speed as long as API. Consequently, at long ranges HEI will land
shorter than API. Since the CM setting for bullet type optimizes the CCIP sight for API, notice
that HEI impacts short at long ranges. The API will be on target and slightly later than the HEI
impacts. This divergence becomes prevalent at slant ranges greater than 12,000 feet in dives of
30 degrees or less; greater than 15,000 feet S/R for 45 degrees of dive and almost negligible in
60-degree HAS. See Figure 7.32, CCIP Gun Reticle with Combat Mix Selected.
Figure 7.32 CCIP Gun Reticle with Combat Mix Selected.
48 25 VFS OI 07-A-10, 25 Jul 2011
7.2.4.6. Precision Attitude Control (PAC). When the gun is fired, aircraft vibration, wind
variations, and other factors can cause errors in pipper placement that are beyond the pilot‟s
ability to see or control through stick inputs. While these errors are small, they are more than
enough to cause increased bullet dispersion and a complete miss. IFFCC compensates for these
errors through the PAC system.
7.2.4.6.1. PAC Arming. The PAC system is available whenever the EAC is armed, the Gun
switch is set to PAC ARM, the Master Arm switch is in ARM or Train, and the air refueling door
is closed. PAC is available in both Guns and CCIP/CCRP. PAC-1 is engaged when the gun
trigger is pulled to the first detent and PAC-2 is engaged at the second detent.
7.2.4.7. Bullets at Target Altitude. IFFCC also incorporates a valuable training tool for feedback
on dry strafe passes. The bullets at target altitude (BATA) is a small flashing circle that appears
in the HUD at the point on the ground where the IFFCC computer predicts the bullets will
impact. This estimation is based on aircraft altitude above the target and bullet TOF for the
calculated slant range. The BATA appears, after the gun trigger is depressed, at the end of the
first bullet‟s TOF expiration when Master Arm is not
safe.
7.2.4.8. Strafe Delivery Techniques.
7.2.4.8.1. During roll-in, set the sight just short of the target and evaluate the slant range.
Approaching the desired slant range (determined by IFFCC cues, ground references, or apparent
target size), pull the pipper up to the target, and track the target. Smoothly squeeze the trigger to
PAC-1, continuing to track the target. Squeeze the trigger to PAC-2 to shoot.
7.2.4.8.2. A cardinal rule for strafe is to “track-shoot-track.” If the pipper was on the target
before and after firing, it probably was on during firing. Rolling in, set the gun sight to the
appropriate aiming reference, stabilize it, and pull to first detent (“track”), smoothly pull the
trigger to the second detent (“shoot”), continue the track momentarily (track), then recover.
• Look at the target when tracking and firing, not at the gun cross.
• Shoot a 2-second burst for tactical situations.
7.2.4.8.3. Combat Offset. Whatever the error from the first attack, learn from that and make a
correction (combat offset).
7.3. Maverick. The AGM-65 Maverick missile is a precise, guided, standoff missile. (See
Figure 7.33, AGM-65D Maverick Missile.) Its accuracy, effective warhead, standoff parameters,
and relative ease of employment can optimize both target destruction and aircraft survivability.
The B/H/K-model Mavericks are the electro-optical (EO) version which uses dark and light
contrast to lock onto targets. The D/G models are infrared (IR) and use heat signatures for target
acquisition. Both Maverick models may also be used in conjunction with other weapons to
enhance delivery capabilities of those weapons. The AGM-65D and G models are also extremely
useful for night target search when a targeting pod is not available. With the current LAU-117,
two Mavericks will be the standard loadout. If LAU-88s are used, a standard loadout of up to six
49 25 VFS OI 07-A-10, 25 Jul 2011
Mavericks is possible. For a more detailed discussion on specific Mavericks, see the AGM-65A
TV Maverick Operations supplement, the AGM-65B TV Maverick Operations supplement, the
AGM-65D Maverick Operations supplement; the AGM-65 G/G2 Maverick Operations
supplement, and the AGM-65 H/K Maverick Operations Supplement.
Figure 7.33 AGM-65D Maverick Missile.
7.3.1. Mission Planning. Successful Maverick employment requires thorough mission planning.
There are many factors that may be known and planned for such as target, weather and threats in
order to determine the appropriate polarity and first lock opportunity slant range.
7.3.1.1. Important target information includes the following:
7.3.1.1.1. Type Target. Know what types of targets are expected for Maverick employment. Be
ready to identify them (tank versus truck) in the MAV MFCD, based on size and shape. The size
and relative shape will also effect the maximum planned launch envelope based on lock logic for
each type of Maverick.
7.3.1.1.2. Target Expectations. Know if the targets are parked or running to aid in polarity
decisions for IR Mavericks. For EO Mavericks, ask intel if the enemy is known to use
Camouflage and Deception to minimize target ID mistakes.
7.3.1.1.3. Target Area Restrictions. Be familiar with planned fire coordination measures, factor
terrain, and threats that might drive specific attack axes. If the enemy is on the move, ask intel in
what direction movement is likely to plan attacks along the movement axis (versus
perpendicular).
50 25 VFS OI 07-A-10, 25 Jul 2011
7.3.1.2. Important weather information includes the following:
7.3.1.2.1. Target area cloud cover. Cloud cover could drive lower altitude employment. Cloud
cover can also reduce shadows and target area heating. Knowing how high the clouds are will be
a consideration when firing missiles with G-bias, as the Mav will lose track if it enters the
clouds.
7.3.1.2.2. Sun Azimuth/Elevation. Sun angle will determine how large the shadows are in
relation to the targets and in what direction the shadows are located. For EO employment
shadows can cause lock logic difficulties. For IR employment, sun direction (and time of day)
has an effect on which side of the target will likely be identifiable in the MAV page.
7.3.1.3. The following Maverick numbers are important to know:
• Time limits: 3-minute EO warm-up; 15 minutes maximum on ground; 3-minute video on per
pass for B-models; 30 minutes video total for each missile per mission; 60 minutes total for EO
power ON; and 45 seconds between passes for missile realignment (B-model only—missile
should not be called up during this time).
• 30 x 30 x 30 Rule: 30 degrees maximum bank angle at lock-on; 30 degrees per second roll rate
at launch; and 30 degrees maximum bank angle change lock-on to launch.
• Launch Envelopes: minimum altitudes are 300 feet AGL for EO and 150 feet AGL for IR; 60-
degree maximum dive angle; G-limits equal +0.5 to +3.0; minimum range equals 10 x KTAS (25
x KTAS for G/G2-model); and TOF equals 1,000 feet per second (3 NM launch equals
approximately 18 seconds). To achieve maximum range launches at lower altitudes, bank angle
at lock should be less than 10 degrees. Each degree of bank will result in 1 percent loss of range.
7.3.1.4. G-Bias. When launched, the missile will initially climb to extend its range. This climb is
referred to as G-Bias. The amount of this climb is based on distance from target when launch
occurs. Firing inside of 12,000 feet slant range minimizes the G-bias.
7.3.2. Target Acquisition and Lock Logic.
7.3.2.1. The “Keyhole.” In order to achieve the “good lock logic” in a D/G/G2/H/K-model
Maverick, the missile seeker must be within the launch window. (See Figure 7.34, D/G
Maverick “Keyhole.”) The launch window is sometimes referred to as “The Keyhole.” This
launch window is one of several considerations to satisfy good lock logic. If the target is inside
these limits, the pointing cross will become steady. If not, the point cross will flash. These limits
are 10 degrees (radius) around the longitudinal axis of the missile and 15 degrees down from the
center. The H/K models have a 10 degree radius keyhole which is not pictured in Figure 7.34,
D/G Maverick “Keyhole.” The B model of the Maverick does not have a “keyhole.”
7.3.2.2. B-Model Lock Logic. A good lock-on for the B-model is indicated when the four white
dots depicting the background gates bound the target and the pointing cross is steady. Lock-on to
a target that is too low in contrast or too small to survive missile launch transients (less than 1/2
the tracking window) is sometimes possible, but the pointing cross and scene magnifiers will
51 25 VFS OI 07-A-10, 25 Jul 2011
flash if the target is too small, or the angle of the missile seeker head from the boresight exceeds
missile limits.
Figure 7.34 D/G Maverick ―Keyhole.‖
7.3.3. Contrast Modes. Look at the target and try to determine which of the following contrast
modes the Maverick will need for a successful lock-on (this should reduce switchology on final).
If tracking the target with an ATP, note the polarity (in charge-coupled devise [CCD] or forward
looking infrared [FLIR]) to determine the polarity for the Maverick to minimize one more switch
change on final.
7.3.3.1. EO Mavericks. For targets which are lighter than the background, select AFT on the boat
switch (polarity switch). For targets which are darker than the background, select forward.
7.3.3.2. IR Mavericks. Is the target hotter or colder than the background? If it is hotter, then the
boat switch should be aft. If it is colder than the background, the switch should be forward.
7.3.3.2.1. Detectable, IR heat signatures result from heating (i.e., friction, solar, or chemical) or
from basic IR properties of materials. Target aspect may either reveal or mask the heat source.
Detection of non-operating targets or of heavy armored targets that have been operating for only
a short time (i.e., slow heat build-up) will depend on the solar heating cycle and the target‟s
specific background temperature. Generally, at night, vegetation cools faster than metal objects,
and conversely, in early morning, vegetation heats up faster than these same objects. There are
many obscurants that will affect IR heat signatures. Besides humidity and precipitation, other
factors which can reduce the apparent temperature difference between a target and its
background include:
52 25 VFS OI 07-A-10, 25 Jul 2011
• High winds.
• Calm water surfaces.
• Dry ground.
• Scattered or broken cloud cover which can vary thermal heating.
• Bare spots on a blanket of snow.
7.3.4. Employment. Ensure a Maverick profile is selected so the missile will fire (Mav will not
fire in sensor mode). To get video, either select the MAV page, or use CHINA HAT-
FWD/SHORT with the MAV profile called up and HUD SOI to automatically switch the MFCD
to Maverick video and make it SOI.
NOTE: Either way, ensure the MFCD is bounded by the green square (MAV is SOI) to prevent
switch errors and/or a dry pass prior to exposure to threats.
7.3.4.1. Roll-In. Pull the Maverick symbol to the target. Ensure that the Maverick symbol has a
chance to stabilize over the target. A good technique is to roll-in in wide field of view (WFOV)
(if available) so that the target area is discernible. In WFOV, at typical employment ranges, the
scene in the MAV should correlate to the features in the MAV SYMBOL on the HUD. Tactical
reference points (e.g., roads, runways) will help funnel the pilot to the target area. Stabilize the
Mav scene: press and hold DMS-FWD/LONG to space stabilize, TMS-AFT/SHORT to ground
stabilize, or CHINA HAT-FWD/LONG to SLAVE TO SPI. Compare the scene to expectations
from visual indications, ATP use, target description, and mission planning. Once the target area
is located and in the center of the MAV page select NFOV.
7.3.4.2. Locking On.
7.3.4.2.1. With a A/B-model Maverick, release the Slew switch and Space Stabilize switch. If the
missile stays locked on, confirm proper mil sizing, a steady pointing cross and confirm positive
target identification. If these criteria are met, the missile is ready for launch. If the target does not
lockup, continue to slew Maverick to target trying for good lock until the pass must be aborted.
7.3.4.2.2. With a D/G/G2/H/K missile, the switchology is almost the same. The biggest
difference is in the WFOV versus NFOV. One technique is to roll-in and acquire the target in
WFOV. WFOV will allow more of the target area to be seen and to help assess target array.
Once acquired, space stabilize (holding the DMS-FWD/LONG while changing the FOV prevents
the missile from returning to the boresight position) and go to NFOV by pushing CHINA HAT-
FWD/SHORT. Once in NFOV, lock target. Another technique is to roll-in and acquire the target
in NFOV. This improves contrast and allows target locks faster and at greater ranges than
WFOV when familiar with the target area, array, or using an ATP to aid in acquisition.
7.3.4.2.3. With a G/K/H/K-model Maverick in Force Correlate mode (i.e., boat switch in the
center position prior to commanding lock), the missile will lock onto specified area. Point the
crosshairs to the target and release the slew switch. The crosshairs will close, creating solid
crosshairs in both the horizontal and vertical axis on the aimpoint in the center of the screen. The
scene must have some contrast to establish a lock, and the pointing cross will indicate when good
lock logic criteria has been met. Do not use on moving or point targets.
53 25 VFS OI 07-A-10, 25 Jul 2011
7.3.4.3. Firing. Ensure the pointing cross is steady for at least 1 second before firing. A flashing
pointing cross indicates that the missile may lose lock at or after launch. The pointing cross will
flash with a D/G/G2/H/K-model if:
• The temperature difference (delta T) between target and background is insufficient (scene
bounding for H/K Mavericks).
• Target size is too small.
• Seeker head exceeds launch angle criteria.
• If there is not a steady cross but the target is locked up, the missile may be out of gimbal limits;
so fly the Maverick towards the flashing cross. For example, if the cross is flashing in the bottom
right of the MAV page, make a right-hand descent; to put the cross within the “keyhole.”
7.3.4.4. Time on Final Considerations. Getting consumed with trying to lockup the target is a
very common problem. Consider time on final to avoid threats, ground impact, and unnecessary
exposure. The flight lead will establish the time of final criteria. Many use 10 seconds for
medium- and high-altitude employment. Set the altitude alert to give a pull off cue on a
Maverick pass.
7.3.4.5. Safe Escape Maneuver. The only SEM for Mavericks is to stop the rate of descent and
climb back out of the threats, if medium altitude, or remask when low altitude. Do not shoot the
Maverick within the minimum safe launch distance:
• For AGM-65B/D/H, 10 x TAS = Abort slant range (typically 300 knots, so 3,000 feet).
• For AGM-65G/K, use 25 x TAS = Abort slant range (7,500 feet).
7.3.4.6. Desired Launch Zone (DLZ). A Maverick desired launch zone is displayed in the HUD
for AGM-65D/G,G2/H/K model Mavericks when NOT in sensor mode. It will also be displayed
in the MAV page when NOT in the sensor mode. The DLZ is not available for B model
Mavericks. It is critical that the correct type of Maverick is loaded in DSMS for an accurate DLZ
display.
7.3.4.7. Non-IFFCC Considerations. The Maverick is one weapon where the loss of IFFCC does
not dramatically affect the delivery process. Losing IFFCC causes two major changes.
7.3.4.7.1. The Maverick reticle will not come up on the HUD. With the loss of the reticle, slant
range information will also be lost.
7.3.4.7.2 For a boresight reference, use the depressible pipper. Dial in the proper mil reference
for where the missile was boresighted. As with the EO Maverick, a picture should be drawn on
the canopy to represent the target-to-pipper relationship. This technique will help expedite target
lock-ons.
7.3.5. Medium Altitude Employment. Employing the Maverick from medium-altitude has
many advantages. Target acquisition is easier from higher altitudes. These higher altitudes may
also allow the pilot to avoid flying into certain threat envelopes. Some key points to consider
54 25 VFS OI 07-A-10, 25 Jul 2011
when employing from medium-altitude include establishing base distance and altitude, and target
acquisition.
7.3.5.1. Base Distance. Establish base distance and altitude based on the planned slant range for
release. Consider the minimum altitude for recovery. See the Battle Book for base parameters
and slant ranges.
7.3.6. Low-Altitude Employment. Employing the Maverick from low-altitude is very similar to
medium-altitude with a few significant differences. One threat is the ground; its Pk is very large.
Budget time spent inside the cockpit and give priority to flying the aircraft. The bottom line is do
not get so consumed in shooting the missile that you hit the ground.
7.3.6.1. A good ROT to use for low-altitude Maverick employment is two slews maximum, then
come off the pass. Altitude alert should be used to provide minimum altitude abort cues. Another
common ROT is no more than 10 seconds on final.
7.3.6.2. The key to success is knowing when, and from where, to unmask from the low-altitude
regime in order to acquire and shoot the target. Take all factors into consideration to establish
this unmask point.
7.3.6.3. Unmask ranges should be established in the brief by the flight lead, but may change in
flight due to actual TDA. Some basic ROTs for unmasking are:
7.3.6.3.1. Target Identification Range. Target identification range is the range where the
boresight can be put on the desired target or target area. This range varies with the means of
target identification used such as targeting pod, FAC mark, or pilot-acquired visual contact with
small point targets. In-flight visibility and other environmental factors play a part in this range.
Do not unmask until the boresight is on a confirmed target/target area.
7.4. Laser Guided Bomb Employment. Laser Guided Bombs such as GBU-12s and GBU-10s
are normally delivered from level/toss CCRP deliveries much like general purpose bombs. In
certain tactical situations, it is also feasible to deliver LGBs from a diving CCIP delivery. The
obvious difference when employing laser-guided bombs is that they require laser energy to guide
to the target. This laser spot is normally provided by either the employing aircraft‟s targeting pod
(known as „Self Lase‟) or by a pod from another aircraft such as the flight lead or wingman
(referred to as „Buddy Lase‟). Laser spots can also be provided by other airborne platforms such
as UAVs, helicopters and AC-130 gunships as well as ground forces using hand-held laser
designators. The general steps for employing an LGB are listed below.
7.4.1. GBU Laser Codes. Laser Codes are normally briefed by the flight lead or are written in
the squadron standards. During the weapons preflight, ensure all LGBs are set to the correct
code. Notify maintenance personnel if there are discrepancies.
7.4.2. Employment.
55 25 VFS OI 07-A-10, 25 Jul 2011
7.4.2..1 CCRP always targets the SPI. In the target area, enter the target coordinates in a
steerpoint and ensure this steerpoint is the current steerpoint in the HUD and also the SPI. A
technique for all CCRP deliveries once the target steerpoint is in the HUD is to TMS-
AFT/LONG to ensure the SPI is set the current steerpoint. Additionally, the SPI type is displayed
in the lower-left corner of the HUD steer point (STPT) and well as the DSMS Status Page. The
DSMS Status Page also displays the SPI coordinates and elevation and these can be compared to
the appropriate target waypoint page on the CDU.
7.4.2.2. Select the appropriate LGB weapons profile using the DMS switch and ensure the
correct stations are armed using the DSMS Quicklook (COOLIE-DOWN/LONG). If the LGB
profile is set to CCRP, the HUD Mode will automatically change to CCRP when the profile is
selected.
7.4.2.3. Confirm that the targeting pod has the correct laser code set. If the TGP laser code is
different from the code set on the weapon in the DSMS Inventory, a caution advisory will be
provided, however, weapon release will not be inhibited. Ensure the TGP is at the correct target
location by either AREA or POINT tracking the desired DMPI or SLAVING to the target
steerpoint.
7.4.2.4. Turn the aircraft towards the target using steering symbols in the HUD (SPI Locator
Line, captains bars). An additional technique is to roll in a slight dive to confirm the location of
the target symbol in the HUD FOV and then pull to wings level.
7.4.2.5. Align the PBRL with the ASL and when the TTRN reads 5 seconds, hold the pickle
button down until the weapon is released. CCRP Consent Option is always „3/9‟ Mode for
LGBs.
7.4.2.6. Buddy Lase. After weapons release, maneuver the aircraft in accordance with the briefed
geometry.
7.4.2.7. Self Lase. After weapons release, check away approximately 45 to 60 degrees in order to
maintain visual and standoff from the target. Normally check left if the targeting pod is loaded
on station 10 to minimize TGP masking. Once rolled out, refine the TGP aimpoint and fire the
laser until weapon impact. Weapon time-of-fall is displayed on the left side of the HUD and in
the lower-right corner of the TGP display.
7.4.2.7.1. It is critical that the laser aimpoint be corrected for winds, specifically the winds
between the surface and 4,000 feet AGL, as these have the most effect on the bomb. Adjust the
laser aimpoint one foot upwind per knot of wind in this regime. High surface winds may require
a laser aimpoint that is completely off the target.
7.4.2.7.2 Laser Guided Bombs require an absolute minimum of 8 seconds of guide time. Guide
times less than this may result in the bomb not hitting the desired point.
7.4.2.8 Common Errors. The following lists common errors encountered when employing LGBs:
56 25 VFS OI 07-A-10, 25 Jul 2011
• Inadvertent HOTAS error that causes TGP laser type to change from laser to IR Marker.
Additionally, LGBs will not guide on the Sniper‟s training laser.
• Not having the TGP on the correct DMPI at release, causing endgame TGP adjustments with a
weapon in the air resulting in a moving laser spot, which will cause the bomb to deplete energy,
for a guide time below the minimum of 8 seconds.
• Not correcting the laser spot for winds.
• Other aircraft firing a laser with the same code into the target area during someone else‟s self
lase attack. This can cause the LGB to guide on the wrong laser.
7.5. Inertially Aided Munitions Employment. . Inertially Aided Munitions include Joint Direct
Attack Munitions such as GBU-38s and GBU-31s as well as Wind Corrected Munitions
Dispensers such as CBU-103. These weapons guide to specific coordinates that can be generated
using aircraft sensors or provided in mission planning. The advantages of these weapons include
relatively large release windows known as Launch Acceptability Regions (LARs) that provide
significant standoff and they can be delivered through the weather. These weapons are employed
using level/toss deliveries in CCRP Mode. However, CCRP symbology for these weapons is
different than laser-guided and GP bombs.
7.5.1. Joint Direct Attack Munitions. The 500-pound GBU-38 and 2000-pound GBU-31
JDAMs are extremely versatile and accurate weapons that can be used against a variety of
targets, especially with the flexibility of cockpit selectable impact, delayed or proximity fuzing
with a FMU-152 Joint Programmable Fuze. The JDAM is a coordinate-seeking weapon and the
coordinates it guides to is the aircraft SPI. When the pickle button is depressed in a JDAM
attack, the current SPI coordinates are sent to the JDAM and the JDAM guides to those
coordinates after release.
7.5.1.1. JDAM Release Sequence. A JDAM contains both an inertial measurement unit (IMU),
much like an INS as well as a GPS. The weapon does not acquire GPS until after release, but the
weapon IMU is aligned to the aircraft EGI. When the pickle button is depressed and the aircraft
SPI coordinates are passed to the weapon, the following steps occur:
7.5.1.1.1. When the weapon is released from the aircraft, its own position is known based on its
internal IMU. It then begins guidance to the target coordinates.
7.5.1.1.2. The weapon searches for GPS satellites and acquires a 3D GPS solution. If the weapon
does not receive a GPS signal, it will guide to the target using only its IMU.
7.5.1.1.3. The weapon will attempt to achieve the desired impact angle and azimuth for hitting
the target (see below). The weapon will sacrifice these parameters in order to hit the target.
7.5.1.2 Relative Targeting. The JDAM has two modes of operation: bomb on coordinate (BOC)
and relative targeting (RT). In BOC mode, the weapon attempts to guide to the exact coordinates
that were passed to it. In RT mode, the JDAM attempts to correct for any errors in its actual
location caused by errors present in the navigation solution of the aircraft. When the weapon
acquires GPS, it compares what it thinks its location is, derived by its own IMU (which was
derived from the aircraft EGI) to the “true location” that the GPS receiver tells it. If there is a
57 25 VFS OI 07-A-10, 25 Jul 2011
difference, the weapon will offset its aimpoint from the passed target coordinates the same
amount. This is because the same platform that told the JDAM where it was in space (the aircraft
EGI) also generated the target coordinates. In the A-10C, which of these modes to use is
automatically determined by the CICU. If the target coordinates were generated by the aircraft,
such as a TGP mark or a target designation cue (TDC) designation, RT mode will be enabled and
„RT‟ will be displayed in the HUD. There are two instances where BOC mode will be used: if
the SPI is a steerpoint with preplanned or hand-entered coordinates loaded into or if a hooked
datalink symbol on the TAD is the SPI. In the former, the target coordinates may be mensurated
coordinates received during mission planning or received over the radio from a joint terminal
attack controller (JTAC). In the latter, another aircraft may broadcast a SADL J12.6 target
sorting message that contain the appropriate coordinates. In neither case is the EGI in the
employing aircraft the “source” of the coordinates and the JDAM will use BOC Mode and
guide to those coordinates without correcting for any location error.
7.5.1.3. Weapon Employment. JDAM employment consists of acquiring target coordinates,
ensuring the SPI reflects those coordinates and maneuvering the aircraft to the weapon LAR for
release. However, there are some significant factors to consider.
7.5.1.3.1. JDAMs are coordinate-seeking weapons, hence the most important element for
successful employment is generating as accurate coordinates as possible. The difference between
coordinates generated by an aircraft sensor such as the targeting pod and the actual target
location is known as target location error (TLE).
7.5.1.3.2. JDAMs always target the SPI. As with other CCRP deliveries, ensuring the aircraft
SPI reflects the desired target is absolutely critical. As with LGBs, the target coordinates should
be input in a steerpoint and then that steerpoint should be the current steerpoint in the HUD.
There are numerous ways to acquire target coordinates, but the end result should be the same -
coordinates in a steerpoint that is the SPI:
• Lase the target with the TGP, take a mark via TMS-RIGHT/SHORT and then copy this mark to
next available steerpoint and label in accordance with the briefed contract.
• If the employing aircraft does not have an operable TGP, a flight member can generate
coordinates with a TGP and pass via a J12.6 SADL Message. The pilot then hooks the Donor
SPI, copies to a empty steerpoint and renames the point.
• If SADL is inoperable, the generating aircraft can pass coordinates via voice and then be hand-
entered into a steerpoint.
7.5.1.3.3. A JDAM-specific FENCE check is the STAIR check, as described in Figure 7.35,
JDAM STAIR Check.
S Steerpoint Ensure target steerpoint is current/in the HUD
T TMS-AFT/LONG Resets SPI to current Steerpoint
A SLAVE ALL Slave all sensors to SPI
I IAM Profile Correct JDAM Profile selected
R Readback Confirm/Readback SPI coordinates on DSMS Status Page
Figure 7.35 JDAM STAIR Check
58 25 VFS OI 07-A-10, 25 Jul 2011
7.5.1.3.4. Once the target steerpoint has been defined and confirmed, maneuver the aircraft to
place the aircraft in the LAR. This is easily accomplished by turning towards the target steerpoint
and centering the captains bars. The left side of the HUD will show the DLZ and if outside the
LAR, the timer will indicate time until max range for the LAR is reached. Once in the LAR, the
HUD will display MAN REL and the timer will change to a predicted time-of-fall. Different
tactical scenarios will dictate where in the LAR to actually release the weapon.
• For normal releases, a release range for a specific set of parameters should be calculated and
then corrected for winds. Once the Range Numeric next to the caret reads 2.3 NM, release the
weapon.
• A less accurate technique for release in order to achieve desired impact angle is to release at
briefed percentage of the LAR, such as 50 percent. When the caret reaches halfway down the
staple, release the weapon. These percentage ROTs may not be valid at all altitudes.
• The JDAM can be released at max range in order to maintain standoff from a collocated threat
or if dropping a JDAM in proximity mode where minimizing elevation error with a 90-degree
impact angle is not desired or required.
CAUTION: The JDAM release sequence can take up to 1.5 seconds to complete, from pickle to
weapon release, due to the fact that at pickle the CICU sends the SPI coordinates to the bomb,
the JDAM repeats those coordinates back and when the CICU verifies that they are the same,
sends the release signal to the JDAM station. If the pickle button is released during this
sequence, it can result in a hung weapon that cannot be released. Hold the pickle button down
until the HUD and/or DSMS indicate that weapon release sequence is complete.
NOTE: JDAMs cannot be released ballistically, unguided or by using a CCIP pipper.
7.5.2. Wind Corrected Munitions Dispensers. WCMD weapons such as CBU-103 and CBU-
104 are delivered using the same HUD symbology and techniques as JDAMs. There are two
significant differences between JDAMs and WCMD.
7.5.2.1. WCMD contains an INS only and does not use GPS.
7.5.2.2. Unlike JDAMs, WCMD can be delivered unguided and they act just like their
conventional counterparts (CBU-87 and CBU-89). Conventional DSMS profiles can be loaded in
additional to the normal guided profiles. In order to drop WCMD in a conventional mode
navigate to the specific 1760 station carrying the CBU on the STAT page and turn it off. Then
select the desired conventional profile and deliver the weapon in either CCRP mode, using the
same CCRP HUD symbology as GP and laser-guided bombs, or by using a CCIP pipper.