madhya pradesh rural road development ... - image

1

MADHYA PRADESH RURAL ROAD DEVELOPMENT AUTHORITY (AN AGENCY OF PANCHYAT & RURAL DEVELOPMENT DEPARTMENT, GOVT. OF M.P.)

Block-II, 5th Floor, Paryavas Bhawan, Bhopal 462011 (M.P. India)

NIB No. 869 (ADB)

R U R A L C O N N E C T I V I T Y I N V E S T M E N T P R O G R A M M E

DETAILED NOTICE INVITING BIDS (NIB) FOR Providing and Installation of Furniture & ELV

in Six RRNMUs at different locations in Madhya Pradesh under Rural Connectivity Investment

Program (RCIP)

No./12874/22/D-12/RRNMU/2019 Bhopal, Dated: 13/09/2019

India has received a loan from the Asian Development Bank towards the cost of the Rural Connectivity

Investment Program (RCIP) under Pradhan Mantri Gram Sadak Yojana and intends to apply a part of the

proceeds of this loan to eligible payments for the following works under RCIP.

Chief General Manager on behalf of MPRRDA (hereinafter referred to as “Purchaser”) invites online item

rate Bids for Providing and Installation of Furniture & ELV on e –procurement portal

https://www.mptenders.gov.in as given below under RCIP on the terms and conditions of the Bidding

Document.

S.No. Name of Work/

Package No.

Description of Work Quantity Bid

Security (in

Rs.)

Bid

submission

fee (in Rs.)

1 2 3 4 5 6

1. MP-05

RRNMU/BPL/02

Providing and Installation of Furniture including related

allied works and maintenance of same in RRNMU

Buildings at Bhopal.

As per Bill

of Quantity

attached

159000/- 11200/-

2. MP-05

RRNMU/BPL/03

Providing and Installation of ELV system, Gadgets Palm

impression, CCTV, Projectors, Projector Screens etc.

including related allied works and maintenance of same

in RRNMU Buildings at Bhopal.

As per Bill

of Quantity

attached

88000/- 5600/-

3. MP-14

RRNMU/GWL/02



Buildings at Gwalior.

As per Bill

of Quantity

attached

145000/- 11200/-

4. MP-14

RRNMU/GWL/03




in RRNMU Buildings at Gwalior.

As per Bill

of Quantity

attached

69000/- 5600/-

5. MP-17

RRNMU/IND/02



Buildings at Indore.

As per Bill

of Quantity

attached

145000/- 11200/-

6. MP-17

RRNMU/IND/03




in RRNMU Buildings at Indore.

As per Bill

of Quantity

attached

69000/- 5600/-

http://www.mptenders.gov.in/

2

S.No. Name of Work/

Package No.

Description of Work Quantity Bid

Security (in

Rs.)

Bid

submission

fee (in Rs.)

1 2 3 4 5 6

7. MP-32

RRNMU/RW/02



Buildings at Rewa.

As per Bill

of Quantity

attached

145000/- 11200/-

8. MP-32

RRNMU/RW/03




in RRNMU Buildings at Rewa.

As per Bill

of Quantity

attached

69000/- 5600/-

9. MP-33

RRNMU/SG/02



Buildings at Sagar.

As per Bill

of Quantity

attached

145000/- 11200/-

10. MP-33

RRNMU/SG/03




in RRNMU Buildings at Sagar.

As per Bill

of Quantity

attached

69000/- 5600/-

11. MP-43

RRNMU/UJ/02



Buildings at Ujjain.

As per Bill

of Quantity

attached

145000/- 11200/-

12. MP-43

RRNMU/UJ/03




in RRNMU Buildings at Ujjain.

As per Bill

of Quantity

attached

69000/- 5600/-

1 (a) The amount of Bid Security is as given in col. 5 above. Bidders are required to pay Bid

Security online as appearing on e-procurement portal plus service charges through Debit

/Credit Card, Internet Banking, or System generated Bank Challan for NEFT / RTGS

before submission of Bid. Bid Security of disqualified / unsuccessful bidders will be refunded

online in the Bank A/c notified by the bidders at the time of submission of Bids. To avoid last

day rush / breakdown in system contractors are advised to ensure payment of Bid Security

at least one day in advance before the end date of Bid Submission. Department will not be

responsible if contractor fails to pay Bid Security due to Server / Power failure or any other

reason.

1 (b) The bidders are required to submit original affidavit strictly on prescribed form (Annexure

‘A’ of this NIB) affirming correctness of information furnished with the bid to MPRRDA

Head Office at Bhopal upto 16.00 hrs. on 14.10.2019. Scanned Copy of this affidavit is to be

uploaded with the technical bid online. If affidavit is not on prescribed form bidder will be

disqualified at envelope ‘A’ stage. The employer will complete technical evaluation process

on the basis of this scanned copy of affidavit. If original affidavit is not submitted within the

prescribed time line or does not match with the scanned copy uploaded online, financial bid

of such bidder will not be opened and Bid Security will be forfeited.

1(c) Bidders are also required to submit Tender Conditions Acceptance Letter in the form given

as Annexure-E, Letter 0f Financial Bid submission in the form given as Annexure-C and

Manufacturer’s Authorization in the form given as Annexure-D to this NIB. List of

documents to be submitted in the technical bid in given is in Annexure-B, Bill of Quantities

Given in Annexure-F and Access to availibity of Credit facilities in Annexure G.

2. Time allowed for completion of supply is – 45 days including rainy season.

3

3. The Bidding Documents containing detailed terms & conditions will be available for free

download on e-Procurement Portal https://mptenders.gov.in starting from (as given in critical

dates table below)

4. The Bidders intending to participate in this Bidding process are required to follow procedures for

registering on the e-Procurement Portal, setting up of Machine, obtaining a digital certificate and

other procedures specific to the e-procurement. Detailed instruction is provided in Annexure –B of

NIB.

5. Bidders may submit their queries online. Submission of queries through online may start right

after posting of Bidding Documents. Bidders may also submit their queries online on Email ID :

[email protected] date and time for online submission of queries is: (as

given in critical dates table below). Offline queries are not permitted.

5.(a) A pre-bid meeting will be held on 24.09.2019 at 11.30 AM at MPRRDA Head Office with the

bidders or their authorized representatives to clarify issues and to answer questions on any matter

that may be raised at that stage.

6. Start date for online submission of Bids is: (as given in critical dates table below).

7. The deadline for the online submission of Bid is as given in critical dates below.

Summary of critical dates for purchase of Bid document and submission of Bid :

Critical Dates

S. No Stages Date & Time

1 Publishing Date 17-09-2019 from 17:00 hrs

2 Document Download/Sale Start

Date 17-09-2019 from 17:30 hrs

3 Seek Clarification Start Date 18-09-2019 from 11:00 hrs

4 Seek Clarification End Date 20-09-2019 from 17:30 hrs

5 Bid Submission Start Date 26-09-2019 from 17:30 hrs

6 Bid Submission Closing Date 11-10-2019 upto 17:30 hrs

7 Bid Opening Date 15-10-2019 from 11:30 hrs

Note:- 1. Original affidavit is to be submitted upto 16:00 hrs. on 14.10.2019

2. Date of Financial Bid opening will be notified on the e-tender portal after technical

bid evaluation

3. Pre-bid meeting 24.09.2019 at 11.30 AM at MPRRDA Head Office Bhopal.

8. As the online Bids are required to be digitally signed, Bidders may obtain information required to

issuance of a appropriate class Digital Signature Certificate from the Controller of Certifying

Authorities https://mptenders.gov.in or the website of Service Provider of Purchaser’s e-

Procurement system.

9. The undersigned has right to extend the deadline for submission of Bids or cancel the Bidding

process without assigning any reason whatsoever.

https://mptenders.gov.in/

mailto:[email protected]

https://mptenders.gov.in/

4

10. Purchaser shall not accept any responsibility for failures or breakdowns of the electronic

procurement system during the e-tendering process. In case of system failure, malfunction, or

breakdown during the bidding process, an email will be sent to all registered Bidders or a notice

will be published on the Purchaser’s e-Procurement Portal notifying that the system is down/was

down (specifying time and duration) and specifying what changes (if any) this may have on the

deadline for submission of Bids and other critical dates as appropriate. The Purchaser accepts no

responsibility for possible local power or equipment failures and Bidders are strongly advised to

submit their Bids well before the deadline.

11. Even though the bidders meet the qualifying criteria, they are subject to be disqualified if

they have made misleading or false representations in the forms, statements, affidavits and

attachments submitted in proof of the qualification requirements. In addition to

disqualification Bid Security of bidder will also be forfeited.

12. Bidders who are black listed / debarred by MPRRDA or in any other department, for

participation in tenders are not allowed to participate in the tenders unless otherwise

decided by MPRRDA. Bidders whose names appear in the debar list of MPRRDA or any

other department on the last date of submission of bid would be disqualified even if their

names are removed from debar list after that date.

13. For a particular package, if lowest rates offered by two or more bidders are equal, they will

be invited to submit revised rates, in sealed envelopes before taking decision on tender.

14. Place of Bid opening is provided in the Bidding Documents. Result of technical evaluation will be

notified on the Employer’s e-Procurement Portal.

15. After completion of the Technical Bid evaluation, the Financial Bids of those Bidders whose

Technical Bids have been evaluated as substantially responsive will be opened at MPRRDA head

quarter (5th

floor, wing II, Paryavas Bhawan, Arera Hills, Bhopal) on the Date and Time given in

key dates. Any change in date & time will be notified on e-Procurement Portal

16. Experience certificate of satisfactory supply of similar equipments in past three year shall be

acceptable if issued by Government Departments/under taking, bodies and authorities only.

17. Any modification amendments or corrigendum will be displayed only online through e-tender

portal, and not notified in news paper. Bidders are requested to update themselves before

submission of bid.

18. The period of the warranty and maintenance which shall include replacement of defective items /

parts and attending maintenance of equipments and furniture shall be Twenty Four (24) months

after the equipment have been delivered, installed (as the case may be) and accepted by purchaser.

19. Agreement will be executed by consignee General Manager of Concerned RRMNU and payment

will also be released by the consignee.

20. Conditions given in this NIB will prevail over the conditions given in the tender document in so

for as they are inconsistent with the conditions of NIB.

5

21. Other details may be seen in the Bidding document for Providing and Installation of Furniture &

ELV for RRMNUs August 2019.

Chief General Manager

M.P. Rural Road Development Authority

Bhopal

End. No./12875/22/D-12/RRNMU/2019 Bhopal, Dated: 13/09/2019

Copy to:

1. Commissioners Public Relation, Ban Ganga Bhopal.

2. Engineer in Chief Public Works Departments, Satpura Bhawan, Bhopal.

3. Chief Engineer, Public Works Departments, Jabalpur/ Gwalior / Indore/ Bhopal/National Highway /

Bridge.

4. Managing Director Rajya Setu Nigam, Arera Hills, Bhopal.

5. Chief Engineer, Central Public Works Departments, Arera Hills, Bhopal.

6. All Divisional Commissioners

7. All Collectors

8. Chief Executive Officers, Zilla Panchayat (all).

9. Chief General Manager, MPRRDA,

10. General Manager Programme Implementation Units.

11. Manager (IT), MPRRDA, Bhopal.

Chief General Manager

M.P. Rural Road Development Authority

Bhopal

6

Salient Features of NIB Sl.

No. Items

Package

no Details

1. NAME OF WORK MP-05

RRNMU/

BPL/02

Providing and Installation of Furniture including related allied

works and maintenance of same in RRNMU Buildings at

Bhopal.

MP-05

RRNMU/

BPL/03



including related allied works and maintenance of same in

RRNMU Buildings at Bhopal.

MP-14

RRNMU/

GWL/02



Gwalior.

MP-14

RRNMU/

GWL/03




RRNMU Buildings at Gwalior.

MP-17

RRNMU/I

ND/02



Indore.

MP-17

RRNMU/I

ND/03




RRNMU Buildings at Indore.

MP-32

RRNMU/

RW/02



Rewa.

MP-32

RRNMU/

RW/03




RRNMU Buildings at Rewa.

MP-33

RRNMU/S

G/02



Sagar.

MP-33

RRNMU/S

G/03




RRNMU Buildings at Sagar.

MP-43

RRNMU/

UJ/02



Ujjain.

7

MP-43

RRNMU/

UJ/03




RRNMU Buildings at Ujjain.

2. PACKAGE NO. : As above As above

3. ESTIMATED COST :

MP-05 RRNMU/BPL/02 INR 79.35 Lacs

MP-05 RRNMU/BPL/03 INR 44.13 Lacs

MP-14 RRNMU/GWL/02 INR 72.27 Lacs

MP-14 RRNMU/GWL/03 INR 34.62 Lacs

MP-17 RRNMU/IND/02 INR 72.27 Lacs

MP-17 RRNMU/IND/03 INR 34.62 Lacs

MP-32 RRNMU/RW/02 INR 72.27 Lacs

MP-32 RRNMU/RW/03 INR 34.62 Lacs

MP-33 RRNMU/SG/02 INR 72.27 Lacs

MP-33 RRNMU/SG/03 INR 34.62 Lacs

MP-43 RRNMU/UJ/02 INR 72.27 Lacs

MP-43 RRNMU/UJ/03 INR 34.62 Lacs

4. TIME PERIOD OF COMPLETION : For all Packages - 45 Days

5.

DATE OF AVAILABILITY OF BID

DOUCMENT ON e-PROCUREMENT

PORTAL : Date 17.09.2019 at 17.30 onwards

6.

LAST DATE FOR RECEIPT OF

QUERIES, IN WRITING/E-MAIL/e-

PROCUREMENT PORTAL : Date 20.09.2019 at 17:30 Hrs

7.

LAST DATE AND TIME FOR

SUBMISSION OF BIDS/uploading of

bid in E-procurement platform : Date 11.10.2019 at 17:30 Hrs

8. PLACE OF BID SUBMISSION : Online

9. TIME AND DATE OF OPENING OF

BIDS As per NIB

10. PLACE OF OPENING OF Technical

BIDS : Office of General Manager of PIU Concerned

11. PLACE OF OPENING OF Financial

BIDS :

MPRRDA Head Quarter (5th floor, wing II, Paryavas Bhawan,

Arera Hills, Bhopal)

8

To be executed on a Non Judicial stamp paper of Rs. 100/- and notarized

Annexure ‘A’

FORMAT OF AFFIDAVIT

Package no. ………………

Affidavit I…………………………S/o………………………………. Aged……………… years resident of

(address……………………………………………………………………..)

(For and behalf of (Name of firm) …………………………………………………..…..), do here

by and herewith solemnly

affirm / state on oath that: -

1. Information furnished with the Bid for the package no. mentioned above is

correct in all respects to the best of my knowledge and belief .

2. No retired gazetted officer who has retired within last two years is in the

employment with the firm.

3. No near relative is working in the department, (Note: - By the term near relatives

is meant Wife, Husband, Parents and Son, Brother, Sister, Brother-in-law, Father-

in-law, Mother-in-law.)

4. *I hereby certify that I have been authorized by ……………………………

…………..…… ..……………………………………… (the bidder) to sign on his /

their behalf, the bid of the package no. mentioned above.

*Not required in case of proprietorship firm

Bidder has to indicate below his signature that

he is proprietor of the firm.

Deponent

(……………………….)

*Strike out whichever is not applicable

*Proprietor/Partner/Authorized signatory

/ for and on behalf

(Name of Firm)

Verification

I………………………………S/o………………………………. do here by affirm that the

contents submitted in Technical & Financial Bid are true to the best of my knowledge and

belief and are based on my / our record.

Verified that this…………….. Date of …………………20__ at (Place)……………….

Deponent

(……………………………..)

Proprietor/Partner/ Authorized signatory

/ for and on behalf

(Name of Firm)

9

Annexure-B Guidelines for Participating in Tender

(Item Rate)

1. For searching Tenders & Tender Document and procedure for submission of Tenders, Bidders should refer

para-3 of this Annexure. In additions, for Submission of Bid (Financial & Technical Bids) Bidders are

advised to go through guidelines given below:

i) For submission of Financial Bid, BOQ Template (Price Schedule) is available on the portal. This

template must not be modified/ replaced by the bidder. This template may be downloaded and

Name of the Bidder should be filled in the relevant line. Bidder should quote the rates in figures in

column-13 of the BOQ. Amount in words will automatically be worked out by the system. Rates

must be quoted against each item, this may be even Zero. Another BOQ as given an Annexure-III

(A) will also appear online & bidder may view Name of Roads, Length and amount of

maintenance cost.

ii) Bidders are not to make entries in any other column or write any condition etc., If BOQ file is

found to be modified by the bidder the bid will be rejected.

iii) After submission of bid, bidder has to click freeze button. If bidder intends to make any changes in

the bid submitted he will have to go to re-submission options available on the portal. After

modification, the Price Bid will have to be again uploaded and frozen. This can be done by the

bidder any number of times before last date of bid submission. Every time bidder will have to

freeze the bid after submission. After successful submission of bid the bidder will get Bid

submission summary a Proof of Bid Submission.

2. (a) Technical Bid :- Scanned copies of the following documents are to be submitted with the Technical

Bid in the Formats given in Section-3.

Packet: I) Scanned copy of Affidavit on prescribed form as given in Annexure-A,

II) Power of Attorney, PAN, GSTN, Manufactures Authorization.

III) Firm organization details of documents defining legal status with partnership dead.

VI) Audited Account last 5 years, Bank credit certificate Clause-5.1 Section-III,

Litigation history.

V) Details of work/supplies in last 5 years, certificate - similar nature of

work/Supplies.

VI) any other Documents Comprising the Bid as specified in the clause 11 Section I(b)-

Instructions to Bidders.

(b) Financial Bid :- In addition to Priced BOQ scanned copy of the letter of Financial Bid is to be

submitted with the Financial Bid in the Format given as Annexure –C of this NIB.

3. Special Instructions to the Contractors/Bidders for the e-submission of the bids online'

through this e-Procurement Portal

1. Bidder should do Online Enrolment in this Portal using the option Click Here to Enroll available in the Home Page. Then the Digital Signature enrollment has to be done with the e-token, after logging into the portal. The e-token may be obtained from one of the Authorized Certifying Authorities such as eMudhraCA/GNFC/IDRBT/MtnlTrustline/ SafeScrpt/TCS.

2. Bidder then logs into the portal giving user id / password chosen during enrollment.

10

3. The e-token that is registered should be used by the' bidder and should not be misused by others.

4. DSC once mapped to an account cannot be remapped to any other account. It can only be inactivated.

5. After downloading / getting the tender schedules, the Bidder should go through them carefully and then submit the documents as per the tender document, otherwise, the bid will be rejected.

6. The BOQ template must not be modified/replaced/renamed by the bidder and the same should be uploaded after filling the relevant Columns, else the bidder is liable to be rejected for that tender. Bidders are allowed to enter the Bidder Name and Values only.

7. Bidder should take into account the corrigendum published before submitting the bids online. 8. Bidder, in advance, should prepare the bid documents to be submitted as indicated in the tender

schedule and they should be in PDF/XLS formats. If there is more than one document, they can be clubbed together.

9. The bidder should read, the terms and conditions and accept the same to proceed further to submit the bids

10. The bidder has to submit the tender document(s) online well in advance before the prescribed time to avoid any delay or problem during the bid submission process.

11. There is no limit on the size of the file uploaded at the server end. However, the upload is decided on the Memory available at the Client System as well as the Network bandwidth available at the client side at that point of time. In order to reduce the file size, bidders are suggested to scan the documents in 75-100 DPI so that the clarity is maintained and also the size of file gets reduced. This will help in quick uploading even at very low bandwidth speed.

12. It is important to note that, the bidder has to click on the Freeze Bid Button, to ensure that he/she completes the Bid Submission Process. Bids which are not frozen are considered as Incomplete/Invalid bids and are not considered for evaluation purposes.

13. The Tender Inviting Authority (TIA) will not be held responsible for any sort of delay or the difficulties faced during the submission of bids online by the bidders due to local issues.

14. The bidder may submit the bid documents online mode only, through this portal. Offline documents will not be handled through this system.

15. At the time of freezing the bid, the e-Procurement system will give a successful bid updation message after uploading all the bid documents submitted and then a bid summary will be shown with the bid no, date & time of submission of the bid with all other relevant details. The documents submitted by the bidders will be digitally signed using the e-token of the bidder and then submitted.

16. After the bid submission, the bid summary has to be printed and kept as an acknowledgement as a token of the submission of the bid. The bid summary will act as a proof of bid submission for a tender floated and will also act as an entry point to participate in the bid opening event.

17. Successful bid submission from the system means, the bids as uploaded by the bidder is received and stored in the system. System does not certify for its correctness.

18. The bidder should see that the bid documents submitted should be free from virus and if the documents could not be opened, due to virus, during tender opening, the bid is liable to be rejected.

19. The time that is displayed from the server clock at the top of the tender Portal, will be valid for all actions of requesting bid submission, bid opening etc., in the e-Procurement portal. The Time followed in this portal is as per Indian Standard Time (IST) which is GMT+5:30. The bidders should adhere to this time during bid submission.

11

20. All the data being entered by the bidders would be encrypted at the client end, and the software

uses PKI encryption techniques to ensure the secrecy of the data. The data entered will not be viewable by unauthorized persons during bid submission and not viewable by anyone until the time of bid opening. Overall, the submitted bid documents become readable only after the tender opening by the authorized individual.

21. During transmission of bid document, the confidentiality of the bids is maintained since the data is transferred over Secured Socket Layer (SSL) with 256 bit encryption technology. Data encryption of sensitive fields is also done.

22. The bidders are requested to submit the bids through online e-Procurement system to the TIA well before the bid submission end date and time (as per Server System Clock).

ASSISTANCE TO BIDDERS

1) Any queries relating to the tender document and the terms and conditions contained therein should be addressed to the Tender Inviting Authority for a tender or the relevant contact person indicated in the tender.

2) Any queries relating to the process of online bid submission or queries relating to MP TENDERS Portal in general may be directed to the 24x7 MP TENDERS Portal Helpdesk.

3) The More information useful for submitting online bids on the MP TENDERS Portal may be

obtained at: https://mptenders.gov.in/nicgep/app

****

https://mptenders.gov.in/nicgep/app

12

Annexure –C

Financial Bid Submission Sheet

Date:

NIB No.:

Invitation for Bid No.:

Alternative No.:

To:

Chief General Manager, MPRRDA Bhopal (M.P.)

We, the undersigned, declare that:

(a) We have examined and have no reservations to the Bidding Document, including Addenda No.: ;

(b) We offer to supply in conformity with the Bidding Document and in accordance with the delivery

schedule specified in the Schedule of Supply, the following Goods and Related Services:

;

(c) The total price of our Bid, excluding any discounts offered in item (d) below is:

;

(d) The discounts offered and the methodology for their application are:

;

(e) Our Bid shall be valid for a period of 90 days from the date fixed for the bid submission deadline in

accordance with the Bidding Document, and it shall remain binding upon us and may be accepted at

any time before the expiration of that period;

(f) If our Bid is accepted, we commit to obtain a Performance Security in the amount of _______percent

of the Contract Price for the due performance of the Contract;

(g) Our firm, including any subcontractors or suppliers for any part of the Contract, have nationalities

from the following eligible countries _____________________________;

(h) We are not participating, as Bidders, in more than one Bid in this bidding process, other than

alternative offers in accordance with the Bidding Document;

(i) Our firm, its affiliates or subsidiaries, including any subcontractors or suppliers for any part of the

Contract, has not been declared ineligible by the ADB;

13

(j) We are not a government owned entity / We are a government owned entity but meet the requirements of

ITB 4.5;

(k) The following commissions, gratuities, or fees have been paid or are to be paid with respect to the bidding

process or execution of the Contract:

Name of Recipient Address Reason Amount

(If none has been paid or is to be paid, indicate “none.”)

(l) We understand that this Bid, together with your written acceptance thereof included in your notification of

award, shall constitute a binding contract between us, until a formal Contract is prepared and executed.

(m) We understand that you are not bound to accept the lowest evaluated bid or any other bid that you may

receive.

(n) We agree to permit ADB or its representative to inspect our accounts and records and other documents

relating to the bid submission and to have them audited by auditors appointed by ADB.

Name

In the capacity of

Signed

Duly authorized to sign the Bid for and on behalf of

Date :-

14

Annexure –D

Manufacturer’s Authorization

Date:

NIB No.:

Invitation for Bid No.:

Alternative No.:

To:

Chief General Manager, MPRRDA Bhopal (M.P.)

WHEREAS___________________________________________________ who are official

manufacturers of ____________________________________________________ having factories at

_______________________________________________________________ do hereby authorize

____________________________________________________ to submit a Bid in relation to the

Invitation for Bids indicated above, the purpose of which is to provide the following Goods,

manufactured by us ______________________________ and to subsequently negotiate and sign the

Contract.

We hereby extend our full guarantee and warranty in accordance with Clause 28 of the General

Conditions of Contract, with respect to the Goods offered by the above firm in reply to this Invitation for

Bids.

Name

In the capacity of:

Signed

Duly authorized to sign the Authorization for and on behalf of

Date

15

Annexure –E

TENDER CONDITION ACCEPTANCE LETTER (To be given by Contractor)

Date: To,

The Chief General Manager MPRRDA, 00 Bhopal (M.P.)

Sub: Acceptance of Terms & Conditions of Tender.

Tender Reference No: (Package No. ………………)

Name of Tender / Work: Providing & Installation OF Furniture/ ELV FOR

RRNMU under Rural Connectivity Investment Program (RCIP ) 1. I/ We have downloaded / obtained the tender document(s) for the above mentioned ‘Tender/Work’ from the web site: www.mptenders.gov.in ______________________________________________________________ ______________________________________________________________ as per your advertisement, given in the above mentioned website(s). 2. I / We hereby certify that I / we have read the entire terms and conditions of the tender documents from Page No. _______ to ______ (including all documents like annexure(s), schedule(s), etc .,), which form part of the contract agreement and I / we shall abide hereby by the terms / conditions / clauses contained therein. 3. The corrigendum(s) issued from time to time by your department/ organisation too have also been taken into consideration, while submitting this acceptance letter. 4. I / We hereby unconditionally accept the tender conditions of above mentioned tender document(s) / corrigendum(s) in its totality / entirety. 5. I / We do hereby declare that our Firm has not been blacklisted/ debarred by any Govt. Department/Public sector undertaking. 6. I / We certify that all information furnished by the our Firm is true & correct and in the event that the information is found to be incorrect/untrue or found violated, then your department/ organisation shall without giving any notice or reason therefore or summarily reject the bid or terminate the contract , without prejudice to any other rights or remedy including the forfeiture of the full said earnest money deposit absolutely.

Yours Faithfully, (Signature of the Bidder, with Official Seal)

16

Annexure-F

Item Rate BOQ Tender Inviting Authority: Madhya Pradesh Rural Road Development Authority , Bhopal

Name of Work: Providing and Installation complete of Furniture including related allied works and maintenance of same in RRNMU Buildings Contract No: MP-05 RRNMU/BPL/02

Name of

the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender.

Bidders are allowed to enter the Bidder Name and Values only )

NUMBER # TEXT # TEXT # NUMBER #

TEXT # NUMBER # NUMBER NUMBER # NUMBER # TEXT #

Sl. No.

Item Description Item Code / Make

Quantity Units BASIC RATE In Figures , including all taxes except GST, To be entered by

the Bidder in Rs. P

GST Amount in INR (on the

amount quoted in

Col. 6), To be entered by

the Bidder in Rs. P

TOTAL AMOUNT With all Taxes, Except GST, in Rs. P

TOTAL AMOUNT With all taxes including GST Taxes Rs. P

Amount in words

1 2 3 4 5 6 7 8 9 10

1 Providing and Installation complete of Furniture including related

allied works and maintenance of same in RRNMU Buildings

1.01 Providing And Placing of BED SIDE TABLE : Body and drawer panels of Bed side table are made of 18 mm thick Prelaminated Particle Board. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding, Side panels are made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trim FIxed on to it. The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich or equivalent. Finish 18 mm thick Prelaminated Particle Board is in Walnut shade. Knock Down construction. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.001 4.000 Nos 0.00 0.00 INR Zero Only

1.02 Providing And Placing of Mobile Pedestal : Under Main Table - Supplying free standing pedestal for office table with dimensions 390 (w) X 440 (d) X 646 (h).Free Standing Full Height Mobile Box Box File. Construction is of Welded Assembled 0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener. 1.2 thk CRCA Top Stiffener & Bottom stiffener. drawer fronts are Metal Front Straight Edge. All Drawers with Double extension precision ball slide 390 wide Pedestals File drawer suitable for storing Fullscape Ezee & Visa files in Depth wise

manner. A4 files in width wise manner For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking is of 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘BoxBoxFile’Pedestal. Top panel Metal Straight Edge Top. the castors are of Swiveling nonlockable Castors mounted below the body shell for Free Standing Full

1.002 5.000 Nos 0.00 0.00 INR Zero Only

17

Height Mobile Pedestal. Fifth roller arrangement mounted below File drawer to avoid toppling of unit when file drawer is pulled out. Finish is of Epoxy Polyester Powder coated to the thickness of 50 microns (+/10). As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.03 Providing And Placing of DRESSING TABLE WITH STOOL : Dressing Table should be made of size - 450W x 440 D x 1710 H mm & Dressing Stool should be made of size - 335 W x 360 D x 450H mm. Panels of Dressing table & Stool should be made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Side panels should be made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims to be fixed on to it. Mirror panel should made of 18 mm thick particle board with 4 mm thick mirror fixed on to it. Supporting pipe used for fixing the mirror frame is to be made of M.S. 25 mm square pipe of thickness 1.2 mm.Stool seat should be made of foam with fabric wrapped on to it. The high quality hardware shall be used like Roller slides, Hinges , minifix, dowels is of make Hettich or equivalent. 18 mm thick Prelaminated Particle Board shall be in Walnut shade finish & knock down condition. Metal pipe should be powder coated in shade Metallic Silver Grey to thickness of 50 microns(+-10). As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.003 2.000 Nos 0.00 0.00 INR Zero Only

1.04 Providing And Placing of Single Bed : The Bed shall be of Size – 2060 L x 1131W x 945 H mm. Bed is constructed around metal frame Metal frame made of M.S. Channels in 1.0mm thickness. Horizontal plinths and bottom plinth are made of 25mm Thick Prelaminated Particle Board. Head Board is made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. Side tail board is made of 18 mm thick Prelaminated Particle Board with importred H.D.F. foil wrapped decorative trims fixed on to it. Mattress panels of bed are made of 18 mm thick Prelaminated Particle Board with all exposed edges banded with 0.8 mm Thick PVC edge banding. Construction – Knock Down. Finish 18 mm thick Prelaminated Particle Board is in Walnut shade. Metal frames are power coated in shade Mat Black to the thickness of 50 microns. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.004 4.000 Nos 0.00 0.00 INR Zero Only

1.05 Providing And Placing DISPLAY RACK : The display rack should be knockdown in construction. Nylon rollers with ball bearing are to be provided for easy tray movement. The inclined retractable tray for display and horizontal metal shelf for storing should be provided. Widthwise stackability should be possible to create bank of racks. The shelf and the retractable tray should be made of 0.8 mm thick CRCA sheet. The sides Steel inserts should be provided in wooden panel for gripping of screws. Total five compartments should be provided. All the metal components should be epoxy powder coated to the thickness of 40-60 microns.

Overall width 900 mm W x 1900 mm H x 400 mm D. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.005 1.000 Nos 0.00 0.00 INR Zero Only

18

1.06 Providing And Placing EXECUTIVE BACK UNIT : The back unit of Size - 1800 x 500 x 750 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.006 1.000 Nos 0.00 0.00 INR Zero Only

1.07 Providing And Placing EXECUTIVE BACK UNIT : The back unit of Size - 1650 x 500 x 1800 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.007 1.000 Nos 0.00 0.00 INR Zero Only

1.08 Providing And Placing of EXECUTIVE MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 2350 x 1150 x 750 with ERU With Pedestal of Size - 1200 x 500 x 750. The primary work surface should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management Secondary work surface ( ERU ) of size - 1200 x 500 x 750 should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening Pedestals are provided with lock for security .As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.008 1.000 Nos 0.00 0.00 INR Zero Only

19

1.09 Providing And Placing of CENTER TABLE for EXECUTIVE Rooms : The table should be of size 1000 W x 600 D x 428 H with Glass top of 08 mm thk tempered and Solid rubber wood legs and frame with MS sheet as bottom shelf. POWDER COATING COLOR & DFT IN MICRONS -40-80 Microns . As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.009 2.000 Nos 0.00 0.00 INR Zero Only

1.1 Providing And Placing of Executive High Back Chair : The High back chair should be made up of 1.2 ±O.1cm. thick hot-pressed plywood and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back is designed with contoured lumber support for extra comfort. The seat has extra thick foam on front edge to give confort to popliteal area. the high back size is 47 cm W x 69.5cm H and the seat size is 47 cm W x 48 cm D. The HR PU foam is moulded with density 45+-2 kg/m cube and hardness load 16 +- 2 kgf as per IS:7888 fof 25% compression. The one piece armrest are injection moulded from black Co Polymer PP. Centre tilt syncro mechanism has 360 degree revolving type, upright position locking, tilt tension adjustment, seat/back ratio of 1:3. The pneumetic height adjustment has an adjustment stroke of 12+- 0.3 cm. Telescopic bellow assy: it is 3 pc telescopic type and injection moulded in black PP. The pedestal is injection moulded in black 33% glass filled Nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal is 66.3 +- 0.5 cm. pitch dia (76.3 +- 1 cm with castors). The twin wheel castors are injection moulded in black nylon. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.010 5.000 Nos 0.00 0.00 INR Zero Only

1.11 Providing And Placing of Mid back chairs : The chair having seat/back assembly made up of 1.2 ±O.1cm. thick hot-pressed plywood measured as per QA method and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back foam to be designed with contoured lumbar support for extra comfort. The seat should have extra thick foam on front edge to give comfort to popliteal area. Back Size should be 47.5 cm. (W) x 58.0 cm. (H) - SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D). The Chair should have HIGH RESILIENCE (HR) POLYURETHANE FOAM.moulded with density =45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression and ARMRESTS which are one-piece injection moulded from black Co. polymer Polypropylene. The chair should have CENTERTILT.SYNCHRO MECHANISM with the following features:• 3600 revolving type.• Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. The Chair shall have PNEUMATIC HEIGHT ADJUSTMENT at stroke of 12.0 ±0.3cm. with TELESCOPIC BELLOW ASSEMBLY with 3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY with injection moulded in black 33% glass-filled.Nylon-66 and fitled with 5.nos. twin wheel castors. The pedestal shall be 66.3 ±O.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.011 36.000 Nos 0.00 0.00 INR Zero Only

20

1.12 Providing And Placing of Visitor Chair Fixed : The chair having SEAT/BACK ASSEMBLY made up of 1.2 ±O.1cm. thick hot-pressed plywood and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat to be extra thick foam on front edge to give comfort to popliteal area. BACK SIZE shall be 47.5 cm. (W) x 58.0 cm. (H)and SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) with HIGH RESILIENCE (HR) POLYURETHANE FOAM to be.moulded with density =45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The ARMRESTS :The one-piece armrests are injection moulded from black Co. polymer Polypropylene. The reading chairs shall have TUBULAR FRAME which is powder coated (OFT 40-60 microns) tubular frame is cantilever type & made of 02.54 ±0.03cm. x 0.2 ±0.016cm.thick. M.S. ER.W. Tube. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.012 30.000 Nos 0.00 0.00 INR Zero Only

1.13 Providing And Placing of Visitor Chair Fixed with Armrest : BACK SIZE - WIDTH (W) : 42.0 CM;DEPTH ; HEIGHT (H) : 26.5 CM . SEAT SIZE (W) : 42.0 CM X 42 CM (D).The HR polyurethane foam should moulded with density = 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The understructure assembly should be cantilever type mainframe of 2.54+/-0.03cm x 0.2+/- 0.016cm thk M.S.E.R.W tube and black powder coated(DFT 40-60 microns). The armrest assembly should be made in twin tube form using 1.58 cm(5/8') x 0.16+/-0.0128 cm thick MSERW tube and black powder coated (DFT 40-60 microns). Chair Dimension shall be 54.0 CM.(W) x 59.5 CM.(D) x 82.5 CM. (H) . As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.013 1.000 Nos 0.00 0.00 INR Zero Only

1.14 Providing And Placing of EXECUTIVE BACK UNIT : The back unit of Size - 2350 x 500 x 750 mm. Top Panel should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Slid e door unit should be made up of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters shall have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.014 1.000 Nos 0.00 0.00 INR Zero Only

21

1.15 Providing And Placing of PREMIUM EXECUTIVE SUITE consist of MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 2100 x 1050 x 750 with ERU with Pedestal of Size - 1200 x 500 x 750.The primary work space should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Secondary Work Unit should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management modesty panel should be made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated pedestal shall be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge.Make - Godrej/ Haworth/ Herman Millar//Wipro//Methodex/durian or Equivalent.

1.015 1.000 Nos 0.00 0.00 INR Zero Only

1.16 Providing And Placing of CPU TROLLEY WITH CASTORS : Metal Tray should be made of 1.0 mm thick MS CRCA Sheet and Side support is made Lockable/Non-lockable twin wheel castors are injection molded in Black of 0.8 mm thick MS CRCA Sheet . As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.016 15.000 Nos 0.00 0.00 INR Zero Only

1.17 Providing And Placing of Dining Table : 8 Seater Dining table with overall dimensions of 970mm W x 2100mm L x 750mmH. The Table shall have Glass top and wooden understurture having 12mm tempered Glass with decorative etching work. The Glass top shall be connected with tapered legs with UV disc. These tapered legs are connected with two rectangular metal (SS) bars which hold the lower wooden (MDF) shelf of white cedar colour suspended underneath for storage. The tapered legs provide a sense of lasting stability and draw attention because of the luminous PU finish and the smooth surface. This eight seater dining table shall be preferably in a dark chocolate finish wooden base with a beveled glass tabletop. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.017 1.000 Nos 0.00 0.00 INR Zero Only

22

1.18 Providing And Placing of Dining Chair :The dining chair should be dark chocolate finished upholstered dinning chair is to be simple yet contemporary for the modern dining room. The chair shall feature a green coloured chenille fabric seat supported by slightlybent back legs and straight front legs . The seat back features a cut out taporized shaped on a slightly curved back pannel. it should not only enhances the aesthetic of thechair but also has a functional aspect aas it helps in lifting or holding the chair Size – 560 x 460 x 905 x 470mm . Net Weight (Kg) 7.95 9 (Appro).. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.018 8.000 Nos 0.00 0.00 INR Zero Only

1.19 Providing And Placing of Table for Lab : The table should be of size width 1500mm X depth 750mm X height 728mm worksurface made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Modesty panel made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Rectangular frame of Fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Legs made of Fabricated component in (Epoxy polyester) & other parts of 0.6mm thick CRCA (IS:513), Finish: PowderPowder coat (Epoxy polyester).Pedestal frame assembly made of 1.2mm thick CRCA (IS:513), Finish: Powder coat38mmx25mmx1.2mm thick MS ERW Tube (IS:7138), Finish: Powder Coated coat (Epoxy polyester) with 10 Lever Cam Lock & Injection Moulded Polypropylene Handle with Nylon6 & MS Bolt levellers. Wire carrier made of 0.7mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.019 2.000 Nos 0.00 0.00 INR Zero Only

1.20 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 500 mm W body & 1 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.020 2.000 Nos 0.00 0.00 INR Zero Only

23

1.21 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 NO. 500 W body & 2 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.021 1.000 Nos 0.00 0.00 INR Zero Only

1.22 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 450mm W x 2025mm H x 500mm D. Along with Add on Units of 2 no. 900 W body. As per drawing & specification and directed by Engineer-in-Charge.Make - Godrej/ Haworth/ Herman Millar/Wipro/Methodex/durian or Equivalent.

1.022 2.000 Nos 0.00 0.00 INR Zero Only

1.23 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.023 2.000 Nos 0.00 0.00 INR Zero Only

24

1.24 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 450mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 900 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.024 4.000 Nos 0.00 0.00 INR Zero Only

1.25 Providing And Placing of Modular steel Almirah : The modular steel body almirah with Wooden doors should have base unit of size - 500 W x 2025 H x 500 D mm & Addon body of size - 500 W x 2025 H x 500 D mm.The body shall be aesthetically appealing plain, made from combination of dent resistance 0.5mm & CRCA 0.8 mm. The appealing doors should be compositely made from MDF Honeycomb and decorative laminate withwooden design finish on both sides and all edges shall be edge banded with 2mm thick PVC lipping Hanging rod shall be 1.0mm thick MS ERW oblong tube and legs should be fitted with screw type leveler. All MS sheet metal and metal frame components shall be powder coated with epoxy polyster powder to the thickness of 50-60microns. Both Base & Addon unit should consist of a lockable Drawer unit. High quality hardware should be used like screw, washer, shelf supporters, lock, Door hinges, Bumper etc. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.025 2.000 Nos 0.00 0.00 INR Zero Only

1.26 Providing And Placing of LIBRARY TABLE - 1200 x 900 x 750mm Providing And Placing DESK based modular workstation having Worksurface made of 25 mm thk prelam particle board with flat pvc lipping edge banding. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.026 2.000 Nos 0.00 0.00 INR Zero Only

25

1.27 Providing And Placing of MAIN DESK 1350 x 600 x 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1350 mm w x 600 mm d . As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.027 5.000 Nos 0.00 0.00 INR Zero Only

1.28 Providing And Placing of MAIN TABLE 1500 x 600 x 750 WITH RETURN DESK 900 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d & 900 mm w x 450 mm d. Each workstation to have one no keyboard pullout tray, CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.028 2.000 Nos 0.00 0.00 INR Zero Only

1.29 Providing And Placing of MAIN TABLE 1500 x 750 x 750 WITH RETURN DESK 1350 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 1350 mm w x 450 mm d. Each workstation to have one CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make - Knoll/Godrej/ Haworth/ Steelcase/ Herman Millar or Equivalent.

1.029 1.000 Nos 0.00 0.00 INR Zero Only

26

1.30 Providing And Placing of MAIN TABLE 1500 x 750 x 750 WITH RETURN DESK 900 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 900 mm w x 450 mm d. Each workstation to have 1 no. CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.030 3.000 Nos 0.00 0.00 INR Zero Only

1.31 Providing And Placing of MAIN TABLE 1800 x 750 x 750 WITH RETURN DESK 1350 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 900 mm w x 450 mm d. Each workstation to have 1 no. CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.031 5.000 Nos 0.00 0.00 INR Zero Only

27

1.32 Providing And Placing of EXECUTIVE HIGH BACK CHAIR LEATHERITE. : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The High Back should be of size 47.7 cm(W) x 76.4 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestion mouldedin plastic having 6.0+0.1cm wheel diameter and assembled to pedestal. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.032 4.000 Nos 0.00 0.00 INR Zero Only

1.33 Providing And Placing of MID BACK CHAIR CONFERENCE ROOM CHAIR : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The Mid Back should be of size 47.7 cm(W) x 60.1 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm

1.033 16.000 Nos 0.00 0.00 INR Zero Only

28

for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestion mouldedin plastic having 6.0+0.1cm wheel diameter and assembled to pedestal.As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.34 Providing And Placing of EXECUTIVE VISITOR FIXED CHAIR : The chair should be of size 60.9 (W) x 64.2 (D) 98.2cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through chrome platedhigh pressure die cast connector piece. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.034 29.000 Nos 0.00 0.00 INR Zero Only

1.35 Providing And Placing of 2 Seater Peon Bench : The bench Having Seat Shell to be a welded assembly of seat, back and side frame.

The Seat & Back frame is to be made up of 1.2mm thk CR steel with Oblong perforations. This is to be welded with side frame of size 32mm width x 5mm thk HR steel. The welded assembly is to be powder coated . The seat shall have have front waterfall edge to provide popliteal clearance for comfortable seating. It shall also have buttock suppport curve for comfartable sitting. SEAT Size- 47.8cm W x 44.6cm D. Back Size- 41.6cm W x 23cm H. Understucture:- Shall consist of connecting beam and leg assembly made up of MS ERW oblong tube of size 75mm x50mm x 2mm thk it shall be welded stucture assembly in powder coating which is to be fitted with shoes and levelers in nylon. Connecting beam shall be fitted with snap locking end cap. Armrest: Armrest assembly shall consist of armrest frame and armrest pad. The Armrest frame size shall be 31.7mm x 4.7mm thk HR steel and it should be powder coated. Armrest pad shall be injected moulded in Nylon and is to be fitted on armrest frame. Overall Dimensions 114.5cm W x 63.8cm D x 44.1cm SH x 78.5cm H. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.035 8.000 Nos 0.00 0.00 INR Zero Only

1.36 Providing And Placing of METAL KEY BOARD TRAY WITH MOUSE TRAY : Tray should be made made of 0.9 mm CRCA sheet Grade as per IS - 513. shall bof Make-Godrej or equivalent of size - 350 long x 11.8mm thk Sigle extensiion 230mm ball slide should be made of combination of 1.2/1.5mmthk roll formed CRCA grade. Mouse tray of size 210 x 210 mm should be provided left or right side of tray made from 0.9 mm thk CRCA sheet As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.036 15.000 Nos 0.00 0.00 INR Zero Only

1.37 Providing And Placing of Pillow : Pillow should made of siliconized fibre of and cover should be of Cotton/ Poleyster fabric duely switched Size 17" X 27" As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.037 4.000 Nos 0.00 0.00 INR Zero Only

29

1.38 Providing And Placing of Single Bed QUILTED BONDED FOAM MATTRESS : The mattress should be Of size - 1981 x 914 x 100 mm.The mattress should be made of Bonded foam thickness 10 mm 18 density & the bonded is of 90 density (kg/m3). Quilting should be done on both side of mattress ,top foam quilting should be 20 mm thick of 18 density foam. Bottom foam quilting should be 20 mm thick and of 18 density foam. total thickness of mattress 160mm +/- 5mm. side boarder quilting shall be of 5mm foam of 18 desnisity,edges should to round Fabric beige of 240 (Non Wooven)Atul Textile or equivalent. Guarantee should be 05 years. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.038 4.000 Nos 0.00 0.00 INR Zero Only

1.39 Providing And Placing of Single Seater Executive Sofa : Overall size of 860 W x 905 D x 820 H mm.With Seating Area of Width 450mm. The seat should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The back should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The under structure should be made of 120mm thick hot pressed plywood (moisture resistance & termite proof as per IS : 303) & pinewood of cross section devoide of major knots & surface defects 6 Nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. legs should be made of stainless steel (grade SS 202) tube & plate with plastic end cap. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.039 2.000 Nos 0.00 0.00 INR Zero Only

1.40 Providing And Placing of Three Seater Executive Sofa : Overall size of 2060 W x 905 D x 820 H mm.With Seating Area of Width 450mm. The seat should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric/Leatherite. The back should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The under structure should be made of 120mm thick hot pressed plywood (moisture resistance & termite proof as per IS : 303) & pinewood of cross section devoide of major knots & surface defects 6 Nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. legs should be made of stainless steel (grade SS 202) tube & plate with plastic end cap. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.040 2.000 Nos 0.00 0.00 INR Zero Only

1.41 Providing And Placing of Center Table : Glass Top Rectangular Center Table should be of size - 1120 W x 600 D x 351 H mm. Glass shall be 12+/- 0.3mm thick black tinted toughened glass Uvglued with bushes made in SS 202 grade for fixing with understructure.Understructure should be welded assembly made in SS202grade having Dia 12+/-0.04 asper IS : 1762. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.041 1.000 Nos 0.00 0.00 INR Zero Only

30

1.42 Providing And Placing of Corner Table : Glass Top Corner Table should be of size - 600 W x 600 D x 351 H mm. Glass shall be 12+/- 0.3mm thick black tinted toughened glass Uvglued with bushes made in SS 202 grade for fixing with understructure.Understructure should be welded assembly made in SS202grade having Dia 12+/-0.04 asper IS : 1762. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.042 2.000 Nos 0.00 0.00 INR Zero Only

1.43 Providing And Placing of Sofa Three Seater : The Sofa should be made of Pine Wood and 12 mm Plywood (IS-303, Commercial Plywood) frame, upholstered with PVC upholstery (1 mm thickness, Weight – GSM - 575) in black color. The Slabstock foam used has to be soft for comfort seating. Seat Foam should be32kg/m3 mm with density of 28 Kg/M3. Back Foam thickness to be 45 mm with density of 28 Kg/M3. Webbing material shall be nylone thread of 2mm Rubberwood legs to be fitted of height 50mm & 95mm dia. The three Seater Overall size: 197.0 cm (W) x 93.5 cm (D) x 92.5 cm (H) As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.043 2.000 Nos 0.00 0.00 INR Zero Only

1.44 Providing And Placing of 2 ARC Reception Table : Top should be in Decorative Laminate Clean matt PU finish 18mm thickInside radius 700.0mm Outside radius – 1350.0 mm Depth – 650 mm. Cork shall be Rubberized cork – 18mm thick. Glass shall be Frosted Glass 10mm thick Diamond cut finishing on edges Inside Radius – 1202.5mm Outside radius – 1402.5mm Depth – 200mm *Note: Angle sustained within arc surface should be 60 deg.Modesty Panel MS Perforated sheet Below Worksurface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) Above Worksurface : 0.8mm (Thick) x 260 mm (height) x 1345.0 mm (flat length).Legs should be made of MS tube 1.6 mm thick Diameter 50.8 mm Height 604 mm. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.044 1.000 Nos 0.00 0.00 INR Zero Only

31

1.45 Providing And Placing OF STORAGE UNIT : The HDU storage unit shall be of size 922 (W) x 750 (H) x 460 (D). Construction shall be in knockdown construction of 25mm thk and 18mm thk Pre -Laminated boards with metal cladding of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness. TOP OPTIONS In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre -laminated board whereas 4.0feet and 4.5feet height Storage units are provided with llmm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±10 microns thickness.DOOR & DOOR OPENING - Single door opening for 450 & 600w units whereas two door opening for all other width options(i.e; 650 /750/800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre -laminated boards with decorative laminate on one side and backing laminate on the other side. SHELVING - 1) Height wise adjustible shelf mounting holes provided on side panels for easy interchange of shelf height as required. 2) Fixed shelves along with adjustible shelves provided only in case of 4.0feet & 4.5feet height units. 3) No fixed shelves for 2.5feet height storage units. 4) 1NO. adjustible shelf for 2.5feet/ 4.0feet/ 4.5feet height and 1NO. Fixed shelf for 4.0feet/ 4.5feet height without vertical partition for 450 / 600 / 650 / 750 /800 /900W whereas 2No. adjustible shelves for 2.5feet/4.0feet/ 4.5feet height and 2No. fixed shelves for 4.0feet/ 4.5feet height with vertical partition in between for 950W & above. 5) A4 SIZE BOX FILES(85Wx345Hx285D) can be stored vertically as shown in pages 4 & 5 respectively.6) Uniformly distributed load capacity for each shelf is 40Kg maximum. SKIRTING OPTION -The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50±10 microns thickness. LEVELER - Screw type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. BACK PANELS - Back panels are made of 18mm thick Pre -Laminated boards with options of Decorative laminate as well as Fabric finishes. 2.5 height units consist of single back panel whereas 4.0' height and 4.5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion . LOCKING MECHANISM - 3 -way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE - Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.045 3.000 Nos 0.00 0.00 INR Zero Only

32

1.46 Providing And Placing OF STORAGE UNIT : The HDU storage unit shall be of size 922 (W) x 1190 (H) x 460 (D). Construction shall be in knockdown construction of 25mm thk and 18mm thk Pre -Laminated boards with metal cladding of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness. TOP OPTIONS In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre -laminated board whereas 4.0feet and 4.5feet height Storage units are provided with llmm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±10 microns thickness.DOOR & DOOR OPENING - Single door opening for 450 & 600w units whereas two door opening for all other width options(i.e; 650 /750/800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre -laminated boards with decorative laminate on one side and backing laminate on the other side. SHELVING - 1) Height wise adjustible shelf mounting holes provided on side panels for easy interchange of shelf height as required. 2) Fixed shelves along with adjustible shelves provided only in case of 4.0feet & 4.5feet height units. 3) No fixed shelves for 2.5feet height storage units. 4) 1NO. adjustible shelf for 2.5feet/ 4.0feet/ 4.5feet height and 1NO. Fixed shelf for 4.0feet/ 4.5feet height without vertical partition for 450 / 600 / 650 / 750 /800 /900W whereas 2No. adjustible shelves for 2.5feet/4.0feet/ 4.5feet height and 2No. fixed shelves for 4.0feet/ 4.5feet height with vertical partition in between for 950W & above. 5) A4 SIZE BOX FILES(85Wx345Hx285D) can be stored vertically as shown in pages 4 & 5 respectively.6) Uniformly distributed load capacity for each shelf is 40Kg maximum. SKIRTING OPTION -The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50±10 microns thickness. LEVELER - Screw type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. BACK PANELS - Back panels are made of 18mm thick Pre -Laminated boards with options of Decorative laminate as well as Fabric finishes. 2.5 height units consist of single back panel whereas 4.0' height and 4.5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion . LOCKING MECHANISM - 3 -way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE - Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing. As per drawing & specification and directed by Engineer-in-Charge.Make -/Godrej/ Haworth/ Steelcase/ Herman Millar/Methodex/durian or Equivalent.

1.046 1.000 Nos 0.00 0.00 INR Zero Only

1.47 Providing And Placing of Slotted Angle Rack : The Slotted Angle racks should be of size - 1829H x 905W x 448D mm having 6 shelves with 6 bend Panel 1mm thick. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.047 6.000 Nos 0.00 0.00 INR Zero Only

33

1.48 Providing And Placing of 18 SEATER Conference Table : The modular Conference Table should have Top thickness 31.6 (18mm + 12mm + 0.6 mm DL(both sides) + 0.4mm Membrane) Edge profile Waterfall Edge 10mm radius on top edge and 5mm at bottom.Single seater 760 W x 600 D, Two seater 1360 W x 600 D Half Round (2 Seater) R 713, Quarter Round (1 Seater) R 713. Legs Made from 25mm PPB having a straight profile with half round edges and clad with 0.6mm thick Post Forming laminate. Overall thickness of leg is 26.2mm. Modesty Panel Made from PLT (Prelaminated Twin) boards of 18mm thick. Wire carrier Made from 0.6mm thick CRCA painted. Wire cover Made of 12mm thk. MDF Painted all over, Substrate MDF. Skin PVC Membrane foil (0.4mm thk) clad on the substrate MDF using PU glue for better adhesion. This foil is pre-coated with layer of polyurethane for better scratch resistance.Sizes to be as per the site measurements and layout. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.048 1.000 Nos 0.00 0.00 INR Zero Only

1.49 Providing And Placing OF STORAGE UNIT : It should have multi bend construction with interlocking design and full length over lapping doors and sides. It should have three way bolting mechanism. All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50-60 dry film thickness. The CRCA steel sheet used for the body is of 20 SWG / guage, as per IS-513 1994. It has 5 shelves made of 22 SWG / guage CRCA steel sheet. It has six lever Mazak Zinc Plated Godrej or equivalent Lock. It has scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It sustains salt spray test of 1000 hrs. as per IS 101. It should have 4 shelves made of 0.8 mm thick CRCA steel sheet. It should have six lever Mazak Zinc Plated Godrej or equivalent Lock. It should sustain salt spray test of 1000 hrs. as per IS 101. Overall size: 198.0 cm (H) x 91.5 cm (W) x 48.5S cm (D). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.049 5.000 Nos 0.00 0.00 INR Zero Only

1.50 Providing And Placing of Office Table : The table is of size 1365 mm (W) x 680 mm (D) x 735 mm (H). The top of table is to be made of 18 mm thick pre-laminated plain particle board. All the edges of the top are duly sealed using 2 mm thick Doelleken beading, fixed by using Jowart/ Klibert glue. Understructure is made in form of ‘C’ frame made of 0.9 mm thk. powder coated CRCA MS Sheet o. The tubular frame is to be made of MS ERW round tubes dia 25.4 mm x 1.2 mm thk. Drawer Unit (Three Drawer + Two Drawer unit) : The shell of the drawer unit is to be made of 0.8 mm thick CRCA MS sheet. The drawer tray is made of 0.6 mm thick CRCA sheet and the drawer front is made of 0.8 mm thick CRCA sheet. Drawer slides are based on friction slides of 1.2 mm thick CRCA sheet. It should have 6 lever brass lock. The handles of drawer are made of ABS plastic.As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.050 1.000 Nos 0.00 0.00 INR Zero Only

34

1.51 Providing And Placing of VISITOR CHAIR FIXED : The chair should be of size 60.9 (W) x 64.3 (D) 99.5cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through powder coated (DFT 40 -60 microns) high pressure die cast connector piece. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.051 10.000 Nos 0.00 0.00 INR Zero Only

1.52 Providing And Placing of full Height Sliding Door Storage Unit : The Full Height Sliding Door Storage Unit should be of size 1830 x 900 x 450 mm It should have Rigid Knock-down construction with press fit riveted design, made from 0.8 mm Prime Quality CRCA steel. Two sliding doors should be provided. It should have snap on type aesthetically appealing die cast 5 lever cam lock and plastic flush recessed handles. Full height sliding doors with top hanging arrangement to prevent derailment and 2 plastic rollers having steel ball bearings. The shelves should be height wise adjustable, with UDL capacity of 80 Kgs. for full length and 40 Kgs. for half shelf. The top should be made of 25 mm thick PLB with 2 mm thick PVC edge banding. .All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50 microns dry film thickness. The CRCA steel sheet used should be 0.6 mm thick as per IS-513 1994. It should have scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It should sustain salt spray test of 1000 hrs. as IS 101. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.052 7.000 Nos 0.00 0.00 INR Zero Only

1.53 Providing And Placing of Media Unit : The media unit should be of size 1200 Wx 398 D x 500 H mm. All the body panels should be made of 18mm thick plelaminated particle board IS : 12823 Class E1,all exposed deges are to be edge banded with 2 mm thick PVC edge banding glue with hot melt EVA glue. Drawers are to be made of 18 mm thick prelaminated particle board IS 12823 high quality hardware to be used like KD fittings, wooden dowels is of Hettich make. 18 mm particle board shall be in CINCINNATI WALNUT Shade. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.053 2.000 Nos 0.00 0.00 INR Zero Only

35

1.54 Providing And Placing of RECTANGULAR WORKSTATION / Linear Workstation of Size: 900mm(W) x 600mm(D) with 3 Drawer Metal Pedestal , keyboard and cpu trolley : Supply of workstations in panel based modular partition system of 1200mm Height And overall thickness shall be 52.4mm. Bottom tiles should be metal/laminate, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.054 10.000 Nos 0.00 0.00 INR Zero Only

1.55 Providing And Placing of RECTANGULAR WORKSTATION / Linear Workstation of Size: 750mm(W) x 600mm(D) with 3 Drawer Metal Pedestal , keyboard and cpu trolley : Supply of workstations in panel based modular partition system of 1200mm Height And overall thickness shall be 52.4mm. Bottom tiles should be metal/laminate, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together. As per drawing & specification and directed by Engineer-in-Charge.Make - Godrej/ Haworth/ Herman Millar/Methodex/durian or Equivalent.

1.055 1.000 Nos 0.00 0.00 INR Zero Only

36

1.56 Providing And Placing of PENTAGONAL Workstation of size- 1350mm(W1) x 600mm(D1) X 1200mm(W2) x 600mm(D2) X 750mm(H) with pedestal , keyboard and cpu trolley : Supply of Workstations in Panel based modular Partition system of 1200mm HEIGHT And overall thickness shall be 52.4mm. Bottom tiles should be metal, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together.Finish: coated with average 50 to 60 micron thicknedd of epoxy powder coating.Work surface shall be made up of 25 mm Pre Laminated finishes. It should be finished with PVC edge bending. The work surface shall be provided with circular cut out of Dia.65mm. Work surface mounted with help of bracket and holder bracket. work surface bracket mounted on to the horizontal extrusion. it is made from 2.0 mm thick CRCA grade D sheet. all the work surface mounted on the brackets through round phillip head diameter 4 mm X 19 length having finish zinc plate. holder bracket made from 2.0 mm thick CRCA grade D sheet. it is slid in between end trim & vertical extrusion & mounted on work surface bracket with the help of pop rivet.for passing of wires. These cut outs shall be provided with ABS covers. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.056 6.000 Nos 0.00 0.00 INR Zero Only

37

1.57 Providing And Placing of PENTAGONAL Workstation of size- 1350mm(W1) x 600mm(D1) X 1350mm(W2) x 600mm(D2) X 750mm(H) with pedestal , keyboard and cpu trolley : Supply of Workstations in Panel based modular Partition system of 1200mm HEIGHT And overall thickness shall be 52.4mm. Bottom tiles should be metal, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together.Finish: coated with average 50 to 60 micron thicknedd of epoxy powder coating.Work surface shall be made up of 25 mm Pre Laminated finishes. It should be finished with PVC edge bending. The work surface shall be provided with circular cut out of Dia.65mm. Work surface mounted with help of bracket and holder bracket. work surface bracket mounted on to the horizontal extrusion. it is made from 2.0 mm thick CRCA grade D sheet. all the work surface mounted on the brackets through round phillip head diameter 4 mm X 19 length having finish zinc plate. holder bracket made from 2.0 mm thick CRCA grade D sheet. it is slid in between end trim & vertical extrusion & mounted on work surface bracket with the help of pop rivet.for passing of wires. These cut outs shall be provided with ABS covers. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.057 1.000 Nos 0.00 0.00 INR Zero Only

1.58 Providing And Placing of Faculty Table : The premium wooden desk which comprises of Work Top , side panels and modesty panels and a free standing padestal. The dimension of the table should be 1500mm (L) X 750mm (W) X 740mm (D). The entire desk unit should be assembled with a suitable knock down fitings and hardware also each side panel shall be provided with cutout or laying cables for the moniter and other computer accessories. The worktop and side panel should be made rom 25 mm thick prelaminated partical board and the edges must be sealed with 2 mm thick PVC edge band all around. the side panel should have two glide screws each for labeling of the desk. Modesty panel must be made from 18 mm thick prelaminated partical board with edges sealed upto 0.8 mm thick PVC edge band all around. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.058 2.000 Nos 0.00 0.00 INR Zero Only

38

1.59 Providing And Placing of Optimizer : The Single Bay Optimiser should consist of Main Body: Rigid Knock Down construction made out of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Each body block (SS/SL/TM) building to consist of 1 Main unit & then Add-on units (0, 1,2,3,4 - depending on no. of bays 1, 2, 3, 4 & 5). Each unit to have 5 loading levels formed by 4 nos. adjustable shelves. Body units are bolted to undercarriage. Height from ground is 2080 mm (1980 body + 65 undercarriage + 35 channel Finish : The bodies including shelves should be given antirust surface treatment & to be powder coated with epoxy polyester powder, involving an 8 step treatment consisting of Hot water rinse, Knock of degreasing, degreasing, cold water rinse, phosphating, cold water rinse, and passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. The testing of paint to be done for various physical & chemical properties as per IS: 101. The material to be then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Shelf: To be made of 0.8 thk CRCA steel conforming to IS: 513 Gr.D or DD. Its max load bearing capacity to be 80 Kg uniformly distributed per shelf for P1 Type of Configuration. Shelves to be mounted on support brackets & shelf level should be adjustable at approx. 25.4 pitches. There should be 4 adjustable shelves per body giving 5 loading levels, if no Cradle pair is provided. Undercarriage: The Undercarriage to be a welded frame made of HR sheet 3.15 mm thk conforming to IS:10748 suitably fabricated to take the loads based on configuration. The undercarriage, after pre-treatment, to be coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 40 microns. Centralized Locking : Centralized locking arrangement to be provided through Locking Stiffener mounted onto back of the Last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock to be of Godrej or equivalent make & placed at suitable height. The arrangement should not occupy space more than 90.0 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. After the unit is moved, before entering into aisle for accessing, this knob shall be rotated to lock position. End stoppers to be provided at the end of channels to prevent derailment. Door Locking / handle: Hinged doors to have Recessed Die cast Handle cum lock giving 3 way locking through a lever & shooting bolts. While Sliding doors should have a die cast lock & separate plastic snap-on handles. Guide Channels consisting of ‘J’ section 2 mm thk HR sheet & 25 mm Square bright bar – both connected by screws. Label Holder to be made from 2 mm thk clear transparent Acrylic sheet & having outer dimension of 155 mm X 106 mm All the nuts & bolts to be galvanized / blackodized / Zn Plated. The Push Pull Type Single Bay Optimiser set should contain 1 no. SL Body of Size - 915mmW x 457mmD x 2080H mm, 1 no. SS Body of Size - 915mmW x 457mmD x 2080H mm, 2 no. TD of Size - 915mmW x 762mmD x 2080H mm. with 15 Feet Length Channels. Design as per Layout. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.059 1.000 Nos 0.00 0.00 INR Zero Only

39

1.60 Providing And Placing of Training room chair with desklet & Arms: SEAT / BACK: The seat sub-assembly is made up of 1.2±0.1cm thk Plywood measured as per QA method described in OCP-QLTA-P14-18 upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and this feature can be used while, cking the chairs horizontally. The back sub-assembly is made up of injection-moulded, inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom area is designed to give comfort to lower back. The back flexing features allows the back to tilt by 9°±2° to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies are fixed to the tubular structure. BACK SIZE: 45 .2cm (W) X 44.6cm (H) SEAT SIZE: ,47.0cm (W) X 50.0cm (D) TUBULAR FRAME STRUCTURE: The powder-coated 4 leg structure is made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R,W. Tube front and rear leg welded along with connecting tube made of 1.9 ±0.02cm dia x 0.2 ±0.016cA1 thk` M.S. E.R.W. Tube to form the tubular frame assembly. The legs are provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use. The chairs can be stacked horizontally when not in use. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 70 ±8 kg/m3 and Hardness load for Seat 16 ± 2 kgf and Hardness load for back 12 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The armrest structure is made up of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube welded to the Tubular Frame structure and having a scratch-resistant ABS Arm top. FULL DESKLET: The Full Desklet assembly is Flip-up type and is made up of extension tube of 1.9 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant ABS desklet top is fixed and covered on bottom side with a bottom cover. BRAKE-LOADED CASTORS: The brake-loaded castors are assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load is applied (while in use) to give a stable feel. The twin wheel castors are injection molded in black Polypropylene. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon +30% GF. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent..

1.060 100.000 Nos 0.00 0.00 INR Zero Only

Total in Figures

0.00 0.00 INR Zero Only

Quoted Rate in Words

INR Zero Only

40

Annexure-F


Providing and Installation complete of Furniture including related allied works and maintenance of same in RRNMU Buildings

Contract No: MP-14 RRNMU/GWL/02, MP-17 RRNMU/IND/02, MP-32 RRNMU/RW/02, MP-33 RRNMU/SG/02, MP-43 RRNMU/UJ/02

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are

allowed to enter the Bidder Name and Values only )



Sl. No.


Quantity Units BASIC RATE In Figures , including all taxes except GST, To be

entered by the Bidder in Rs. P


amount quoted in

Col. 6), To be entered by

the Bidder in Rs. P



Amount in words

1 2 3 4 5 6 7 8 9 10

1 Providing and Installation complete of Furniture including

related allied works and maintenance of same in RRNMU

Buildings

1.01 Providing And Placing of BED SIDE TABLE : Body and drawer panels of Bed side table are made of 18 mm thick Prelaminated Particle Board. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding, Side panels are made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trim FIxed on to it. The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich or equipment . Finish 18 mm thick Prelaminated Particle Board is in Walnut shade. Knock Down construction. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.001 4.000 Nos 0.00 0.00 INR Zero Only

1.02 Providing And Placing of Mobile Pedestal : Under Main Table - Supplying free standing pedestal for office table with dimensions 390 (w) X 440 (d) X 646 (h).Free Standing Full Height Mobile Box Box File. Construction is of Welded Assembled 0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener. 1.2 thk CRCA Top Stiffener & Bottom stiffener. drawer fronts are Metal Front Straight Edge. All Drawers with Double extension precision ball slide 390 wide Pedestals File drawer suitable for storing Fullscape Ezee & Visa files in Depth wise manner. A4 files in width wise manner For Drawer pulling, side wise tapered

1.002 5.000 Nos 0.00 0.00 INR Zero Only

41

recess provided in shell behind Drawer Fronts. Locking is of 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘BoxBoxFile’Pedestal. Top panel Metal Straight Edge Top. the castors are of Swiveling nonlockable Castors mounted below the body shell for Free Standing Full Height Mobile Pedestal. Fifth roller arrangement mounted below File drawer to avoid toppling of unit when file drawer is pulled out. Finish is of Epoxy Polyester Powder coated to the thickness of 50 microns (+/10). As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.03 Providing And Placing of DRESSING TABLE WITH STOOL : Dressing Table should be made of size - 450W x 440 D x 1710 H mm & Dressing Stool should be made of size - 335 W x 360 D x 450H mm. Panels of Dressing table & Stool should be made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Side panels should be made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims to be fixed on to it. Mirror panel should made of 18 mm thick particle board with 4 mm thick mirror fixed on to it. Supporting pipe used for fixing the mirror frame is to be made of M.S. 25 mm square pipe of thickness 1.2 mm.Stool seat should be made of foam with fabric wrapped on to it. The high quality hardware shall be used like Roller slides, Hinges , minifix, dowels is of make Hettich or equipment. 18 mm thick Prelaminated Particle Board shall be in Walnut shade finish & knock down condition. Metal pipe should be powder coated in shade Metallic Silver Grey to thickness of 50 microns(+-10). As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.003 2.000 Nos 0.00 0.00 INR Zero Only

1.04 Providing And Placing of Single Bed : The Bed shall be of Size – 2060 L x 1131W x 945 H mm. Bed is constructed around metal frame Metal frame made of M.S. Channels in 1.0mm thickness. Horizontal plinths and bottom plinth are made of 25mm Thick Prelaminated Particle Board. Head Board is made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. Side tail board is made of 18 mm thick Prelaminated Particle Board with importred H.D.F. foil wrapped decorative trims fixed on to it. Mattress panels of bed are made of 18 mm thick Prelaminated Particle Board with all exposed edges banded with 0.8 mm Thick PVC edge banding. Construction – Knock Down. Finish 18 mm thick Prelaminated Particle Board is in Walnut shade. Metal frames are power coated in shade Mat Black to the thickness of 50 microns. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.004 4.000 Nos 0.00 0.00 INR Zero Only

1.05 Providing And Placing DISPLAY RACK : The display rack should be knockdown in construction. Nylon rollers with ball bearing are to be provided for easy tray movement. The inclined retractable tray for display and horizontal metal shelf for storing should be provided. Widthwise stackability should be possible to create bank of racks. The shelf and the retractable tray should be made of 0.8 mm thick CRCA sheet. The sides Steel inserts should be provided in wooden panel

1.005 1.000 Nos 0.00 0.00 INR Zero Only

42

for gripping of screws. Total five compartments should be provided. All the metal components should be epoxy powder coated to the thickness of 40-60 microns. Overall width 900 mm W x 1900 mm H x 400 mm D. As per drawing & specification and directed by Engineer-in-Charge. Make - Knoll/Godrej/ Haworth/ Steelcase/ Herman Millar//WiproMethodex/durian or Equivalent.

1.06 Providing And Placing EXECUTIVE BACK UNIT : The back unit of Size - 1800 x 500 x 750 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.006 1.000 Nos 0.00 0.00 INR Zero Only

1.07 Providing And Placing EXECUTIVE BACK UNIT : The back unit of Size - 1650 x 500 x 1800 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.007 1.000 Nos 0.00 0.00 INR Zero Only

43

1.08 Providing And Placing of EXECUTIVE MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 2350 x 1150 x 750 with ERU With Pedestal of Size - 1200 x 500 x 750. The primary work surface should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management Secondary work surface ( ERU ) of size - 1200 x 500 x 750 should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening Pedestals are provided with lock for security .As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.008 1.000 Nos 0.00 0.00 INR Zero Only

1.09 Providing And Placing of CENTER TABLE for EXECUTIVE Rooms : The table should be of size 1000 W x 600 D x 428 H with Glass top of 08 mm thk tempered and Solid rubber wood legs and frame with MS sheet as bottom shelf. POWDER COATING COLOR & DFT IN MICRONS -40-80 Microns . As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.009 2.000 Nos 0.00 0.00 INR Zero Only

1.1 Providing And Placing of Executive High Back Chair : The High back chair should be made up of 1.2 ±O.1cm. thick hot-pressed plywood and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back is designed with contoured lumber support for extra comfort. The seat has extra thick foam on front edge to give confort to popliteal area. the high back size is 47 cm W x 69.5cm H and the seat size is 47 cm W x 48 cm D. The HR PU foam is moulded with density 45+-2 kg/m cube and hardness load 16 +- 2 kgf as per IS:7888 fof 25% compression. The one piece armrest are injection moulded from black Co Polymer PP. Centre tilt syncro mechanism has 360 degree revolving type, upright position locking, tilt tension adjustment, seat/back ratio of 1:3. The pneumetic height adjustment has an adjustment stroke of 12+- 0.3 cm. Telescopic bellow assy: it is 3 pc telescopic type and injection moulded in black PP. The pedestal is injection moulded in black 33% glass filled Nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal is 66.3 +- 0.5 cm. pitch dia (76.3 +- 1 cm with castors). The twin wheel castors are injection moulded in black nylon. As per drawing & specification and directed by Engineer-in-Charge. Make - Godrej/ Haworth/ Herman Millar//WiproMethodex/durian or Equivalent.

1.010 5.000 Nos 0.00 0.00 INR Zero Only

44

1.11 Providing And Placing of Mid back chairs : The chair having seat/back assembly made up of 1.2 ±O.1cm. thick hot-pressed plywood measured as per QA method and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back foam to be designed with contoured lumbar support for extra comfort. The seat should have extra thick foam on front edge to give comfort to popliteal area. Back Size should be 47.5 cm. (W) x 58.0 cm. (H) - SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D). The Chair should have HIGH RESILIENCE (HR) POLYURETHANE FOAM.moulded with density =45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression and ARMRESTS which are one-piece injection moulded from black Co. polymer Polypropylene. The chair should have CENTERTILT.SYNCHRO MECHANISM with the following features:• 3600 revolving type.• Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. The Chair shall have PNEUMATIC HEIGHT ADJUSTMENT at stroke of 12.0 ±0.3cm. with TELESCOPIC BELLOW ASSEMBLY with 3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY with injection moulded in black 33% glass-filled.Nylon-66 and fitled with 5.nos. twin wheel castors. The pedestal shall be 66.3 ±O.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.011 36.000 Nos 0.00 0.00 INR Zero Only

1.12 Providing And Placing of Visitor Chair Fixed : The chair having SEAT/BACK ASSEMBLY made up of 1.2 ±O.1cm. thick hot-pressed plywood and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat to be extra thick foam on front edge to give comfort to popliteal area. BACK SIZE shall be 47.5 cm. (W) x 58.0 cm. (H)and SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) with HIGH RESILIENCE (HR) POLYURETHANE FOAM to be.moulded with density =45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The ARMRESTS :The one-piece armrests are injection moulded from black Co. polymer Polypropylene. The reading chairs shall have TUBULAR FRAME which is powder coated (OFT 40-60 microns) tubular frame is cantilever type & made of 02.54 ±0.03cm. x 0.2 ±0.016cm.thick. M.S. ER.W. Tube. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.012 30.000 Nos 0.00 0.00 INR Zero Only

45

1.13 Providing And Placing of Visitor Chair Fixed with Armrest : BACK SIZE - WIDTH (W) : 42.0 CM;DEPTH ; HEIGHT (H) : 26.5 CM . SEAT SIZE (W) : 42.0 CM X 42 CM (D).The HR polyurethane foam should moulded with density = 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The understructure assembly should be cantilever type mainframe of 2.54+/-0.03cm x 0.2+/- 0.016cm thk M.S.E.R.W tube and black powder coated(DFT 40-60 microns). The armrest assembly should be made in twin tube form using 1.58 cm(5/8') x 0.16+/-0.0128 cm thick MSERW tube and black powder coated (DFT 40-60 microns). Chair Dimension shall be 54.0 CM.(W) x 59.5 CM.(D) x 82.5 CM. (H) . As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.013 1.000 Nos 0.00 0.00 INR Zero Only

1.14 Providing And Placing of EXECUTIVE BACK UNIT : The back unit of Size - 2350 x 500 x 750 mm. Top Panel should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Slid e door unit should be made up of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters shall have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.014 1.000 Nos 0.00 0.00 INR Zero Only

46

1.15 Providing And Placing of PREMIUM EXECUTIVE SUITE consist of MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 2100 x 1050 x 750 with ERU with Pedestal of Size - 1200 x 500 x 750.The primary work space should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Secondary Work Unit should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management modesty panel should be made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated pedestal shall be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.015 1.000 Nos 0.00 0.00 INR Zero Only

1.16 Providing And Placing of CPU TROLLEY WITH CASTORS : Metal Tray should be made of 1.0 mm thick MS CRCA Sheet and Side support is made Lockable/Non-lockable twin wheel castors are injection molded in Black of 0.8 mm thick MS CRCA Sheet . As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.016 15.000 Nos 0.00 0.00 INR Zero Only

1.17 Providing And Placing of Dining Table : 8 Seater Dining table with overall dimensions of 970mm W x 2100mm L x 750mmH. The Table shall have Glass top and wooden understurture having 12mm tempered Glass with decorative etching work. The Glass top shall be connected with tapered legs with UV disc. These tapered legs are connected with two rectangular metal (SS) bars which hold the lower wooden (MDF) shelf of white cedar colour suspended underneath for storage. The tapered legs provide a sense of lasting stability and draw attention because of the luminous PU finish and the smooth surface. This eight seater dining table shall be preferably in a dark chocolate finish wooden base with a beveled glass tabletop. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.017 1.000 Nos 0.00 0.00 INR Zero Only

47

1.18 Providing And Placing of Dining Chair :The dining chair should be dark chocolate finished upholstered dinning chair is to be simple yet contemporary for the modern dining room. The chair shall feature a green coloured chenille fabric seat supported by slightlybent back legs and straight front legs . The seat back features a cut out taporized shaped on a slightly curved back pannel. it should not only enhances the aesthetic of thechair but also has a functional aspect aas it helps in lifting or holding the chair Size – 560 x 460 x 905 x 470mm . Net Weight (Kg) 7.95 ( Appro.). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.018 8.000 Nos 0.00 0.00 INR Zero Only

1.19 Providing And Placing of Table for Lab : The table should be of size width 1500mm X depth 750mm X height 728mm worksurface made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Modesty panel made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Rectangular frame of Fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Legs made of Fabricated component in (Epoxy polyester) & other parts of 0.6mm thick CRCA (IS:513), Finish: PowderPowder coat (Epoxy polyester).Pedestal frame assembly made of 1.2mm thick CRCA (IS:513), Finish: Powder coat38mmx25mmx1.2mm thick MS ERW Tube (IS:7138), Finish: Powder Coated coat (Epoxy polyester) with 10 Lever Cam Lock & Injection Moulded Polypropylene Handle with Nylon6 & MS Bolt levellers. Wire carrier made of 0.7mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.019 4.000 Nos 0.00 0.00 INR Zero Only

1.20 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 500 mm W body & 1 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.020 2.000 Nos 0.00 0.00 INR Zero Only

48

1.21 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 NO. 500 W body & 2 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.021 1.000 Nos 0.00 0.00 INR Zero Only

1.22 Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 450mm W x 2025mm H x 500mm D. Along with Add on Units of 2 no. 900 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.022 2.000 Nos 0.00 0.00 INR Zero Only


1.023 2.000 Nos 0.00 0.00 INR Zero Only

49


1.024 4.000 Nos 0.00 0.00 INR Zero Only

1.25 roviding And Placing of Modular steel Almirah : The modular steel body almirah with Wooden doors should have base unit of size - 500 W x 2025 H x 500 D mm & Addon body of size - 500 W x 2025 H x 500 D mm.The body shall be aesthetically appealing plain, made from combination of dent resistance 0.5mm & CRCA 0.8 mm. The appealing doors should be compositely made from MDF Honeycomb and decorative laminate withwooden design finish on both sides and all edges shall be edge banded with 2mm thick PVC lipping Hanging rod shall be 1.0mm thick MS ERW oblong tube and legs should be fitted with screw type leveler. All MS sheet metal and metal frame components shall be powder coated with epoxy polyster powder to the thickness of 50-60microns. Both Base & Addon unit should consist of a lockable Drawer unit. High quality hardware should be used like screw, washer, shelf supporters, lock, Door hinges, Bumper etc. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.025 2.000 Nos 0.00 0.00 INR Zero Only

1.26 Providing And Placing of LIBRARY TABLE - 1200 x 900 x 750mm Providing And Placing DESK based modular workstation having Worksurface made of 25 mm thk prelam particle board with flat pvc lipping edge banding. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.026 2.000 Nos 0.00 0.00 INR Zero Only

50

1.27 Providing And Placing of MAIN DESK 1350 x 600 x 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1350 mm w x 600 mm d . As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.027 5.000 Nos 0.00 0.00 INR Zero Only

1.28 Providing And Placing of MAIN TABLE 1500 x 600 x 750 WITH RETURN DESK 900 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d & 900 mm w x 450 mm d. Each workstation to have one no keyboard pullout tray, CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.028 2.000 Nos 0.00 0.00 INR Zero Only

51

1.29 Providing And Placing of MAIN TABLE 1500 x 750 x 750 WITH RETURN DESK 1350 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 1350 mm w x 450 mm d. Each workstation to have one CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.029 1.000 Nos 0.00 0.00 INR Zero Only

1.30 Providing And Placing of MAIN TABLE 1500 x 750 x 750 WITH RETURN DESK 900 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 900 mm w x 450 mm d. Each workstation to have 1 no. CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.030 3.000 Nos 0.00 0.00 INR Zero Only

52

1.31 Providing And Placing of MAIN TABLE 1800 x 750 x 750 WITH RETURN DESK 1350 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 900 mm w x 450 mm d. Each workstation to have 1 no. CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.031 5.000 Nos 0.00 0.00 INR Zero Only

53

1.32 Providing And Placing of EXECUTIVE HIGH BACK CHAIR LEATHERITE. : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The High Back should be of size 47.7 cm(W) x 76.4 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestion mouldedin plastic having 6.0+0.1cm wheel diameter and assembled to pedestal. As per drawing & specification and directed by Engineer-in-Charge.Make - Godrej/ Haworth/ Herman MillarMethodex/durian or Equivalent.

1.032 4.000 Nos 0.00 0.00 INR Zero Only

54

1.33 Providing And Placing of MID BACK CHAIR CONFERENCE ROOM CHAIR : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The Mid Back should be of size 47.7 cm(W) x 60.1 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestion mouldedin plastic having 6.0+0.1cm wheel diameter and assembled to pedestal.As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.033 16.000 Nos 0.00 0.00 INR Zero Only

1.34 Providing And Placing of EXECUTIVE VISITOR FIXED CHAIR : The chair should be of size 60.9 (W) x 64.2 (D) 98.2cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through chrome platedhigh pressure die cast connector piece. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.034 29.000 Nos 0.00 0.00 INR Zero Only

55

1.35 Providing And Placing of 2 Seater Peon Bench : The bench Having Seat Shell to be a welded assembly of seat, back and side frame. The Seat & Back frame is to be made up of 1.2mm thk CR steel with Oblong perforations. This is to be welded with side frame of size 32mm width x 5mm thk HR steel. The welded assembly is to be powder coated . The seat shall have have front waterfall edge to provide popliteal clearance for comfortable seating. It shall also have buttock suppport curve for comfartable sitting. SEAT Size- 47.8cm W x 44.6cm D. Back Size- 41.6cm W x 23cm H. Understucture:- Shall consist of connecting beam and leg assembly made up of MS ERW oblong tube of size 75mm x50mm x 2mm thk it shall be welded stucture assembly in powder coating which is to be fitted with shoes and levelers in nylon. Connecting beam shall be fitted with snap locking end cap. Armrest: Armrest assembly shall consist of armrest frame and armrest pad. The Armrest frame size shall be 31.7mm x 4.7mm thk HR steel and it should be powder coated. Armrest pad shall be injected moulded in Nylon and is to be fitted on armrest frame. Overall Dimensions 114.5cm W x 63.8cm D x 44.1cm SH x 78.5cm H. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.035 8.000 Nos 0.00 0.00 INR Zero Only

1.36 Providing And Placing of METAL KEY BOARD TRAY WITH MOUSE TRAY : Tray should be made made of 0.9 mm CRCA sheet Grade as per IS - 513. shall bof Make-Godrej or equipment of size - 350 long x 11.8mm thk Sigle extensiion 230mm ball slide should be made of combination of 1.2/1.5mmthk roll formed CRCA grade. Mouse tray of size 210 x 210 mm should be provided left or right side of tray made from 0.9 mm thk CRCA sheet As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.036 15.000 Nos 0.00 0.00 INR Zero Only

1.37 Providing And Placing of Pillow : Pillow should made of siliconized fibre of and cover should be of Cotton/ Poleyster fabric duely switched Size 17" X 27" As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.037 4.000 Nos 0.00 0.00 INR Zero Only

1.38 Providing And Placing of Single Bed QUILTED BONDED FOAM MATTRESS : The mattress should be Of size - 1981 x 914 x 100 mm.The mattress should be made of Bonded foam thickness 10 mm 18 density & the bonded is of 90 density (kg/m3). Quilting should be done on both side of mattress ,top foam quilting should be 20 mm thick of 18 density foam. Bottom foam quilting should be 20 mm thick and of 18 density foam. total thickness of mattress 160mm +/- 5mm. side boarder quilting shall be of 5mm foam of 18 desnisity,edges should to round Fabric beige of 240 (Non Wooven)Atul Textile or equipment. Guarantee should be 05 years. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.038 4.000 Nos 0.00 0.00 INR Zero Only

56

1.39 Providing And Placing of Single Seater Executive Sofa : Overall size of 860 W x 905 D x 820 H mm.With Seating Area of Width 450mm. The seat should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The back should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The under structure should be made of 120mm thick hot pressed plywood (moisture resistance & termite proof as per IS : 303) & pinewood of cross section devoide of major knots & surface defects 6 Nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. legs should be made of stainless steel (grade SS 202) tube & plate with plastic end cap. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.039 2.000 Nos 0.00 0.00 INR Zero Only

1.40 Providing And Placing of Three Seater Executive Sofa : Overall size of 2060 W x 905 D x 820 H mm.With Seating Area of Width 450mm. The seat should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric/Leatherite. The back should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The under structure should be made of 120mm thick hot pressed plywood (moisture resistance & termite proof as per IS : 303) & pinewood of cross section devoide of major knots & surface defects 6 Nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. legs should be made of stainless steel (grade SS 202) tube & plate with plastic end cap. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.040 2.000 Nos 0.00 0.00 INR Zero Only

1.41 Providing And Placing of Center Table : Glass Top Rectangular Center Table should be of size - 1120 W x 600 D x 351 H mm. Glass shall be 12+/- 0.3mm thick black tinted toughened glass Uvglued with bushes made in SS 202 grade for fixing with understructure.Understructure should be welded assembly made in SS202grade having Dia 12+/-0.04 asper IS : 1762. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.041 1.000 Nos 0.00 0.00 INR Zero Only

1.42 Providing And Placing of Corner Table : Glass Top Corner Table should be of size - 600 W x 600 D x 351 H mm. Glass shall be 12+/- 0.3mm thick black tinted toughened glass Uvglued with bushes made in SS 202 grade for fixing with understructure.Understructure should be welded assembly made in SS202grade having Dia 12+/-0.04 asper IS : 1762. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.042 2.000 Nos 0.00 0.00 INR Zero Only

57

1.43 Providing And Placing of Sofa Three Seater : The Sofa should be made of Pine Wood and 12 mm Plywood (IS-303, Commercial Plywood) frame, upholstered with PVC upholstery (1 mm thickness, Weight – GSM - 575) in black color. The Slabstock foam used has to be soft for comfort seating. Seat Foam should be32kg/m3 mm with density of 28 Kg/M3. Back Foam thickness to be 45 mm with density of 28 Kg/M3. Webbing material shall be nylone thread of 2mm Rubberwood legs to be fitted of height 50mm & 95mm dia. The three Seater Overall size: 197.0 cm (W) x 93.5 cm (D) x 92.5 cm (H) As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.043 2.000 Nos 0.00 0.00 INR Zero Only

1.44 Providing And Placing of 2 ARC Reception Table : Top should be in Decorative Laminate Clean matt PU finish 18mm thickInside radius 700.0mm Outside radius – 1350.0 mm Depth – 650 mm. Cork shall be Rubberized cork – 18mm thick. Glass shall be Frosted Glass 10mm thick Diamond cut finishing on edges Inside Radius – 1202.5mm Outside radius – 1402.5mm Depth – 200mm *Note: Angle sustained within arc surface should be 60 deg.Modesty Panel MS Perforated sheet Below Worksurface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) Above Worksurface : 0.8mm (Thick) x 260 mm (height) x 1345.0 mm (flat length).Legs should be made of MS tube 1.6 mm thick Diameter 50.8 mm Height 604 mm. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.044 1.000 Nos 0.00 0.00 INR Zero Only

58

1.45 Providing And Placing OF STORAGE UNIT : The HDU storage unit shall be of size 922 (W) x 750 (H) x 460 (D). Construction shall be in knockdown construction of 25mm thk and 18mm thk Pre -Laminated boards with metal cladding of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness. TOP OPTIONS In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre -laminated board whereas 4.0feet and 4.5feet height Storage units are provided with llmm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±10 microns thickness.DOOR & DOOR OPENING - Single door opening for 450 & 600w units whereas two door opening for all other width options(i.e; 650 /750/800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre -laminated boards with decorative laminate on one side and backing laminate on the other side. SHELVING - 1) Height wise adjustible shelf mounting holes provided on side panels for easy interchange of shelf height as required. 2) Fixed shelves along with adjustible shelves provided only in case of 4.0feet & 4.5feet height units. 3) No fixed shelves for 2.5feet height storage units. 4) 1NO. adjustible shelf for 2.5feet/ 4.0feet/ 4.5feet height and 1NO. Fixed shelf for 4.0feet/ 4.5feet height without vertical partition for 450 / 600 / 650 / 750 /800 /900W whereas 2No. adjustible shelves for 2.5feet/4.0feet/ 4.5feet height and 2No. fixed shelves for 4.0feet/ 4.5feet height with vertical partition in between for 950W & above. 5) A4 SIZE BOX FILES(85Wx345Hx285D) can be stored vertically as shown in pages 4 & 5 respectively.6) Uniformly distributed load capacity for each shelf is 40Kg maximum. SKIRTING OPTION -The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50±10 microns thickness. LEVELER - Screw type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. BACK PANELS - Back panels are made of 18mm thick Pre -Laminated boards with options of Decorative laminate as well as Fabric finishes. 2.5 height units consist of single back panel whereas 4.0' height and 4.5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion . LOCKING MECHANISM - 3 -way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE - Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.045 3.000 Nos 0.00 0.00 INR Zero Only

59

1.46 Providing And Placing OF STORAGE UNIT : The HDU storage unit shall be of size 922 (W) x 1190 (H) x 460 (D). Construction shall be in knockdown construction of 25mm thk and 18mm thk Pre -Laminated boards with metal cladding of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness. TOP OPTIONS In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre -laminated board whereas 4.0feet and 4.5feet height Storage units are provided with llmm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±10 microns thickness.DOOR & DOOR OPENING - Single door opening for 450 & 600w units whereas two door opening for all other width options(i.e; 650 /750/800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre -laminated boards with decorative laminate on one side and backing laminate on the other side. SHELVING - 1) Height wise adjustible shelf mounting holes provided on side panels for easy interchange of shelf height as required. 2) Fixed shelves along with adjustible shelves provided only in case of 4.0feet & 4.5feet height units. 3) No fixed shelves for 2.5feet height storage units. 4) 1NO. adjustible shelf for 2.5feet/ 4.0feet/ 4.5feet height and 1NO. Fixed shelf for 4.0feet/ 4.5feet height without vertical partition for 450 / 600 / 650 / 750 /800 /900W whereas 2No. adjustible shelves for 2.5feet/4.0feet/ 4.5feet height and 2No. fixed shelves for 4.0feet/ 4.5feet height with vertical partition in between for 950W & above. 5) A4 SIZE BOX FILES(85Wx345Hx285D) can be stored vertically as shown in pages 4 & 5 respectively.6) Uniformly distributed load capacity for each shelf is 40Kg maximum. SKIRTING OPTION -The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50±10 microns thickness. LEVELER - Screw type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. BACK PANELS - Back panels are made of 18mm thick Pre -Laminated boards with options of Decorative laminate as well as Fabric finishes. 2.5 height units consist of single back panel whereas 4.0' height and 4.5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion . LOCKING MECHANISM - 3 -way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE - Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing. As per drawing & specification and directed by Engineer-in-Charge.Make - Knoll/Godrej/ Haworth/ Steelcase/ Herman Millar or Equivalent.

1.046 1.000 Nos 0.00 0.00 INR Zero Only

1.47 Providing And Placing of Slotted Angle Rack : The Slotted Angle racks should be of size - 1829H x 905W x 448D mm having 6 shelves with 6 bend Panel 1mm thick. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.047 6.000 Nos 0.00 0.00 INR Zero Only

60

1.48 Providing And Placing of 18 SEATER Conference Table : The modular Conference Table should have Top thickness 31.6 (18mm + 12mm + 0.6 mm DL(both sides) + 0.4mm Membrane) Edge profile Waterfall Edge 10mm radius on top edge and 5mm at bottom.Single seater 760 W x 600 D, Two seater 1360 W x 600 D Half Round (2 Seater) R 713, Quarter Round (1 Seater) R 713. Legs Made from 25mm PPB having a straight profile with half round edges and clad with 0.6mm thick Post Forming laminate. Overall thickness of leg is 26.2mm. Modesty Panel Made from PLT (Prelaminated Twin) boards of 18mm thick. Wire carrier Made from 0.6mm thick CRCA painted. Wire cover Made of 12mm thk. MDF Painted all over, Substrate MDF. Skin PVC Membrane foil (0.4mm thk) clad on the substrate MDF using PU glue for better adhesion. This foil is pre-coated with layer of polyurethane for better scratch resistance.Sizes to be as per the site measurements and layout. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.048 1.000 Nos 0.00 0.00 INR Zero Only

1.49 Providing And Placing OF STORAGE UNIT : It should have multi bend construction with interlocking design and full length over lapping doors and sides. It should have three way bolting mechanism. All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50-60 dry film thickness. The CRCA steel sheet used for the body is of 20 SWG / guage, as per IS-513 1994. It has 5 shelves made of 22 SWG / guage CRCA steel sheet. It has six lever Mazak Zinc Plated Godrej or equipment Lock. It has scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It sustains salt spray test of 1000 hrs. as per IS 101. It should have 4 shelves made of 0.8 mm thick CRCA steel sheet. It should have six lever Mazak Zinc Plated Godrej or equipment Lock. It should sustain salt spray test of 1000 hrs. as per IS 101. Overall size: 198.0 cm (H) x 91.5 cm (W) x 48.5S cm (D). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.049 6.000 Nos 0.00 0.00 INR Zero Only

1.50 Providing And Placing of Office Table : The table is of size 1365 mm (W) x 680 mm (D) x 735 mm (H). The top of table is to be made of 18 mm thick pre-laminated plain particle board. All the edges of the top are duly sealed using 2 mm thick Doelleken beading, fixed by using Jowart/ Klibert glue. Understructure is made in form of ‘C’ frame made of 0.9 mm thk. powder coated CRCA MS Sheet o. The tubular frame is to be made of MS ERW round tubes dia 25.4 mm x 1.2 mm thk. Drawer Unit (Three Drawer + Two Drawer unit) : The shell of the drawer unit is to be made of 0.8 mm thick CRCA MS sheet. The drawer tray is made of 0.6 mm thick CRCA sheet and the drawer front is made of 0.8 mm thick CRCA sheet. Drawer slides are based on friction slides of 1.2 mm thick CRCA sheet. It should have 6 lever brass lock. The handles of drawer are made of ABS plastic.As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.050 1.000 Nos 0.00 0.00 INR Zero Only

61

1.51 Providing And Placing of VISITOR CHAIR FIXED : The chair should be of size 60.9 (W) x 64.3 (D) 99.5cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through powder coated (DFT 40 -60 microns) high pressure die cast connector piece. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.051 10.000 Nos 0.00 0.00 INR Zero Only

1.52 Providing And Placing of full Height Sliding Door Storage Unit : The Full Height Sliding Door Storage Unit should be of size 1830 x 900 x 450 mm It should have Rigid Knock-down construction with press fit riveted design, made from 0.8 mm Prime Quality CRCA steel. Two sliding doors should be provided. It should have snap on type aesthetically appealing die cast 5 lever cam lock and plastic flush recessed handles. Full height sliding doors with top hanging arrangement to prevent derailment and 2 plastic rollers having steel ball bearings. The shelves should be height wise adjustable, with UDL capacity of 80 Kgs. for full length and 40 Kgs. for half shelf. The top should be made of 25 mm thick PLB with 2 mm thick PVC edge banding. .All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50 microns dry film thickness. The CRCA steel sheet used should be 0.6 mm thick as per IS-513 1994. It should have scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It should sustain salt spray test of 1000 hrs. as IS 101. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.052 7.000 Nos 0.00 0.00 INR Zero Only

1.53 Providing And Placing of Media Unit : The media unit should be of size 1200 Wx 398 D x 500 H mm. All the body panels should be made of 18mm thick plelaminated particle board IS : 12823 Class E1,all exposed deges are to be edge banded with 2 mm thick PVC edge banding glue with hot melt EVA glue. Drawers are to be made of 18 mm thick prelaminated particle board IS 12823 high quality hardware to be used like KD fittings, wooden dowels is of Hettich make. 18 mm particle board shall be in CINCINNATI WALNUT Shade. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.053 2.000 Nos 0.00 0.00 INR Zero Only

62

1.54 Providing And Placing of RECTANGULAR WORKSTATION / Linear Workstation of Size: 900mm(W) x 600mm(D) with 3 Drawer Metal Pedestal , keyboard and cpu trolley : Supply of workstations in panel based modular partition system of 1200mm Height And overall thickness shall be 52.4mm. Bottom tiles should be metal/laminate, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.054 10.000 Nos 0.00 0.00 INR Zero Only

63

1.55 Providing And Placing of RECTANGULAR WORKSTATION / Linear Workstation of Size: 750mm(W) x 600mm(D) with 3 Drawer Metal Pedestal , keyboard and cpu trolley : Supply of workstations in panel based modular partition system of 1200mm Height And overall thickness shall be 52.4mm. Bottom tiles should be metal/laminate, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.055 1.000 Nos 0.00 0.00 INR Zero Only

64

1.56 Providing And Placing of PENTAGONAL Workstation of size- 1350mm(W1) x 600mm(D1) X 1200mm(W2) x 600mm(D2) X 750mm(H) with pedestal , keyboard and cpu trolley : Supply of Workstations in Panel based modular Partition system of 1200mm HEIGHT And overall thickness shall be 52.4mm. Bottom tiles should be metal, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together.Finish: coated with average 50 to 60 micron thicknedd of epoxy powder coating.Work surface shall be made up of 25 mm Pre Laminated finishes. It should be finished with PVC edge bending. The work surface shall be provided with circular cut out of Dia.65mm. Work surface mounted with help of bracket and holder bracket. work surface bracket mounted on to the horizontal extrusion. it is made from 2.0 mm thick CRCA grade D sheet. all the work surface mounted on the brackets through round phillip head diameter 4 mm X 19 length having finish zinc plate. holder bracket made from 2.0 mm thick CRCA grade D sheet. it is slid in between end trim & vertical extrusion & mounted on work surface bracket with the help of pop rivet.for passing of wires. These cut outs shall be provided with ABS covers. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.056 6.000 Nos 0.00 0.00 INR Zero Only

65

1.57 Providing And Placing of PENTAGONAL Workstation of size- 1350mm(W1) x 600mm(D1) X 1350mm(W2) x 600mm(D2) X 750mm(H) with pedestal , keyboard and cpu trolley : Supply of Workstations in Panel based modular Partition system of 1200mm HEIGHT And overall thickness shall be 52.4mm. Bottom tiles should be metal, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together.Finish: coated with average 50 to 60 micron thicknedd of epoxy powder coating.Work surface shall be made up of 25 mm Pre Laminated finishes. It should be finished with PVC edge bending. The work surface shall be provided with circular cut out of Dia.65mm. Work surface mounted with help of bracket and holder bracket. work surface bracket mounted on to the horizontal extrusion. it is made from 2.0 mm thick CRCA grade D sheet. all the work surface mounted on the brackets through round phillip head diameter 4 mm X 19 length having finish zinc plate. holder bracket made from 2.0 mm thick CRCA grade D sheet. it is slid in between end trim & vertical extrusion & mounted on work surface bracket with the help of pop rivet.for passing of wires. These cut outs shall be provided with ABS covers. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.057 1.000 Nos 0.00 0.00 INR Zero Only

1.58 Providing And Placing of Faculty Table : The premium wooden desk which comprises of Work Top , side panels and modesty panels and a free standing padestal. The dimension of the table should be 1500mm (L) X 750mm (W) X 740mm (D). The entire desk unit should be assembled with a suitable knock down fitings and hardware also each side panel shall be provided with cutout or laying cables for the moniter and other computer accessories. The worktop and side panel should be made rom 25 mm thick prelaminated partical board and the edges must be sealed with 2 mm thick PVC edge band all around. the side panel should have two glide screws each for labeling of the desk. Modesty panel must be made from 18 mm thick prelaminated partical board with edges sealed upto 0.8 mm thick PVC edge band all around. As per drawing & specification and directed by Engineer-in-

1.058 1.000 Nos 0.00 0.00 INR Zero Only

66

Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.59 Providing And Placing of Optimizer : The Single Bay Optimiser should consist of Main Body: Rigid Knock Down construction made out of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Each body block (SS/SL/TM) building to consist of 1 Main unit & then Add-on units (0, 1,2,3,4 - depending on no. of bays 1, 2, 3, 4 & 5). Each unit to have 5 loading levels formed by 4 nos. adjustable shelves. Body units are bolted to undercarriage. Height from ground is 2080 mm (1980 body + 65 undercarriage + 35 channel Finish : The bodies including shelves should be given antirust surface treatment & to be powder coated with epoxy polyester powder, involving an 8 step treatment consisting of Hot water rinse, Knock of degreasing, degreasing, cold water rinse, phosphating, cold water rinse, and passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. The testing of paint to be done for various physical & chemical properties as per IS: 101. The material to be then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Shelf: To be made of 0.8 thk CRCA steel conforming to IS: 513 Gr.D or DD. Its max load bearing capacity to be 80 Kg uniformly distributed per shelf for P1 Type of Configuration. Shelves to be mounted on support brackets & shelf level should be adjustable at approx. 25.4 pitches. There should be 4 adjustable shelves per body giving 5 loading levels, if no Cradle pair is provided. Undercarriage: The Undercarriage to be a welded frame made of HR sheet 3.15 mm thk conforming to IS:10748 suitably fabricated to take the loads based on configuration. The undercarriage, after pre-treatment, to be coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 40 microns. Centralized Locking : Centralized locking arrangement to be provided through Locking Stiffener mounted onto back of the Last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock to be of Godrej or equipment make & placed at suitable height. The arrangement should not occupy space more than 90.0 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. After the unit is moved, before entering into aisle for accessing, this knob shall be rotated to lock position. End stoppers to be provided at the end of channels to prevent derailment. Door Locking / handle: Hinged doors to have Recessed Die cast Handle cum lock giving 3 way locking through a lever & shooting bolts. While Sliding doors should have a die cast lock & separate plastic snap-on handles. Guide Channels consisting of ‘J’ section 2 mm thk HR sheet & 25 mm Square bright bar – both connected by screws. Label Holder to be made from 2 mm thk clear transparent Acrylic sheet & having outer dimension of 155 mm X 106 mm All the nuts & bolts to be galvanized / blackodized / Zn Plated. The Push Pull Type Single Bay Optimiser set should contain 1 no. SL Body of Size - 915mmW x 457mmD x 2080H mm, 1 no. SS Body of Size - 915mmW x 457mmD x 2080H mm, 2 no. TD of Size -

1.059 1.000 Nos 0.00 0.00 INR Zero Only

67

915mmW x 762mmD x 2080H mm. with 15 Feet Length Channels. Design as per Layout. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.60 Providing And Placing of Training room chair with desklet & Arms: SEAT / BACK: The seat sub-assembly is made up of 1.2±0.1cm thk Plywood measured as per QA method described in OCP-QLTA-P14-18 upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and this feature can be used while, cking the chairs horizontally. The back sub-assembly is made up of injection-moulded, inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom area is designed to give comfort to lower back. The back flexing features allows the back to tilt by 9°±2° to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies are fixed to the tubular structure. BACK SIZE: 45 .2cm (W) X 44.6cm (H) SEAT SIZE: ,47.0cm (W) X 50.0cm (D) TUBULAR FRAME STRUCTURE: The powder-coated 4 leg structure is made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R,W. Tube front and rear leg welded along with connecting tube made of 1.9 ±0.02cm dia x 0.2 ±0.016cA1 thk` M.S. E.R.W. Tube to form the tubular frame assembly. The legs are provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use. The chairs can be stacked horizontally when not in use. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 70 ±8 kg/m3 and Hardness load for Seat 16 ± 2 kgf and Hardness load for back 12 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The armrest structure is made up of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube welded to the Tubular Frame structure and having a scratch-resistant ABS Arm top. FULL DESKLET: The Full Desklet assembly is Flip-up type and is made up of extension tube of 1.9 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant ABS desklet top is fixed and covered on bottom side with a bottom cover. BRAKE-LOADED CASTORS: The brake-loaded castors are assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load is applied (while in use) to give a stable feel. The twin wheel castors are injection molded in black Polypropylene. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon +30% GF. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

1.060 40.000 Nos 0.00 0.00 INR Zero Only

Total in Figures



INR Zero Only

68

Annexure-F

Item Rate BOQ Tender Inviting Authority : Madhya Pradesh Rural Road Development Authority , Bhopal

Name of Work : Providing and Installation complete of ELV system, Gadgets Palm impression, CCTV, Projectors, Projector Screens etc. including related allied works and maintenance of same in RRNMU Building BHOPAL.

Contract No: MP-05 RRNMU/BPL/03


PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders

are allowed to enter the Bidder Name and Values only )


TEXT # NUMBER # NUMBER NUMBER #

NUMBER #

TEXT #

Sl. No.


Quantity Units BASIC RATE In Figures , including all taxes except GST, To be entered by

the Bidder in Rs. P


amount quoted in Col. 6), To be entered by the

Bidder in Rs. P



Amount in words

1 2 3 4 5 6 7 8 9 10

1 Providing and Installation complete of ELV system, Gadgets Palm

impression, CCTV, Projectors, Projector Screens etc. including related

allied works and maintenance of same in RRNMU Building BHOPAL.

1.01 Providing, fixing,installation and commissioning of DLP Projector with , 4,500 lumens, 16:10 Native, 16:9 and 4:3 Compatible, Contrast Ratio 20,000:1, WXGA resolution,Single 0.65″ WXGA DC3 DMD chip DLP Technology,Displayable Colors -1.07 billion,Audio -10W speaker,Inputs -HDMI v1.4a, two VGA-in,composite video, two audio-in, VESA 3D Sync port, RS-232C, RJ45 & mini USB-B,Keystone Correction -± 40° Vertical,Outputs -VGA out, audio out, (3.5mm) etc.complete, as per the direction of engineer incharge. Make : EPSON/Optoma / Infocus or Equivalent.

1.001 3.000 Each 0.00 0.00 INR Zero Only

1.02 Providing, fixing,installation and commissioning of Motorized lift for projector ,Projector lift is powered by strong tubular motors,loading capacity 20 KG,voltage 220V,come complete with spider projector bracket suitable for all projectors,RF remote control.etc.complete, as per the direction of engineer incharge. Make :SUVIRA/LIBARTY/ LOGIC /AV Space or Equivalent.


1.03 Providing,fixing,installation and commissioning of Motorized Projection Screen with RF Remote Control Type – Motorized Size(HxW) – 8 feet X10 feet ,wide angle vision,black masking border to get best image quality,inbuilt electric motor 220V. etc.complete, as per the direction of engineer incharge. Make : Star Screen / Liberty/SUVIRA/AV Space or Equivalent.


69

1.04 Providing,fixing,installation and commissioning of Dual Channel Power Amplifier 2 X 120 Watts @ 100V / 4 Ω, Bridge Mode 1 X 240 Watts @ 100V / 8 Ω , Class D Amp Topology , Convection Cool, 1 U 19" Rackmount etc.complete, as per the direction of engineer incharge. Make : Bose /APART/ Martin Audio / L-Acoustic/Ahuja/Sony or Equivalent.


1.05 Providing,fixing,installation and commissioning of Design cabinet speaker, 5.25" coated paper cone woofer + 1" silk dome tweeter, 100v/30Watts or 16Ω/80Watts,etc.complete, as per the direction of engineer incharge. Make : Bose /APART/ Martin Audio / L-Acoustic/Ahuja or Equivalent.


1.06 Providing,fixing,installation and commissioning of Audio DSP having

balanced mic inputs, 2 balanced Mic/Line inputs and 1 stereo unbalanced input, 1 stereo and 2 mono outputs,2-channel USB audio interface for soft codec, integration or playback from computer,Full digital processing on inputs and outputs,8 x 3 audio routing matrix,6-channel Smart Mix (gate or gain sharing),etc.complete, as per the direction of engineer incharge. Make : Sennheiser/Audio technica/Extron or Equivalent

1.006 1.000 Each 0.00 0.00 INR Zero

Only

1.07 Providing,fixing,installation and commissioning of Wireless handheld microphone set , Up to 12 compatible channels, External antennas, True diversity receiver with metal housing, Automatic frequency management , AF frequency response, 80-14,000 Hz, Switching bandwidth up to 24 MHz, Operating time approx. 10 hrs,Pick-up pattern cardioid etc.complete, as per the direction of engineer incharge. Make : AKG / Sennheiser/Shure / EV or Equivalent.


1.08 Providing,fixing,installation and commissioning of short microphone stand as per the direction of engineer incharge. Make : Ahuja/K&M/AVSpace or Equivalent.


1.09 Providing,fixing,installation and commissioning of Wireless Lavalier microphone set, Up to 12 compatible channels, External antennas, True diversity receiver with metal housing, Automatic frequency management , AF frequency response, 50 to 16,000 Hz, Switching bandwidth up to 24 MHz, Operating time approx. 10 hrs,Pick-up pattern omnidirectional etc.complete, as per the direction of engineer incharge. Make : AKG / Sennheiser/Shure / EV or Equivalent.


1.1 Providing,fixing,installation and commissioning of 65" touch LED display;Panel resolution 1920x1080p;contrast ratio 5000:1,aspect ratio 16:9,brightness 500cd/m2,lifetime -minimum 80000 hours,viewing angle 178 degrees,16.7 M colours,Wireless mirroring,free annotating software,10 point infrared touch technology,stylus set,USB Screen Projection Dongle,Inputs-DisplayPort, Touch USB,HDMI x 2, VGA, Audio In, USB 3.0 x 2, AV In, YPbPr, SD Card,RS 232,Output-AV Out, Audio Out, SPDI,OPERATING HUMIDITY 10% to 80%,OPERATING TEMPERATURE 0°C to 50°C,CPU ARM Quad-core Cortex-A53 1.4GHz ,USB 3.0 x 2, USB 2.0 x3,LAN 10/100 Ethernet,WI-FI 802.11b/g/n/ac,OSAndroid 5.0.1 complete with all accessories as required. as per the direction of engineer incharge. Make : Christie/Newline/Allsee Technologies/Barco or Equivalent.


1.11 Providing,fixing,installation and commissioning of Indigeneous Digital Lectern in Metallic Frame : Providing & Fixing of Built-in 19” Interactive Panel with motorized tilting, 1xGooseneck Microphone, Top Control Panel VGA, HDMI, USB x 2, Power, VGA Switcher connectivity, built-in 19" Rack for amplifier,CPU. etc.complete, as per the direction of engineer incharge.


70

Make : UNI / Tecom / Peoplelink/AVSPACE or Equivalent.

1.12 Providing,fixing,installation and commissioning of video conference system with 9 party (1+8) MCU, 12X optical zoom camera,Wi-Fi, Bluetooth, SIP / VoIP & H.323, Android based supporting Skype,VC Recording feature,minimum 3 HDMI Display out,Presentation sharing etc complete, as per the direction of engineer incharge. Make : Polycom/Grandstream/Cisco or Equivalent.


1.13 Providing,fixing,installation and commissioning of hidden Connection Box, Mechanical Locking Device, Smooth Pneumatic Support Structure, VGA with Audio, HDMI, Network / Telephone, Power , Neat & elegant topside, Input voltage: 110V-220V / 50-60Hx, RCA, 3.5 mm Audio Jack, USB, Surface Mountable Enclosure for Cables etc.complete, as per the direction of engineer incharge. Make : Extron/Crestron/AV Space or Equivalent.


1.14 Providing,fixing,installation and commissioning of AV equipment rack 12U complete, as per the direction of engineer incharge. Make : Comrack/INET/AV Space or Equivalent.


1.15 Providing,fixing,installation and commissioning of 2-core loudspeaker cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.015 300.000 Mtr 0.00 0.00 INR Zero Only

1.16 Providing,fixing,installation and commissioning of 2-core Mic Cable.etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.016 200.000 Mtr 0.00 0.00 INR Zero Only

1.17 Providing,fixing,installation and commissioning of RGB Cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.017 100.000 Mtr 0.00 0.00 INR Zero Only

1.18 Providing,fixing,installation and commissioning of 20 mtr HDMI Cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.






1.21 Providing,fixing,installation and commissioning of Lan CAT6 cable etc.complete, as per the direction of engineer incharge. Make : Dlink/Panduit/AMP or Equivalent

1.021 1.000 set 0.00 0.00 INR Zero Only

1.22 Providing,fixing,installation and commissioning of Interconnect cables,connectors including accessories, booster , couplers etc. complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.022 1.000 set 0.00 0.00 INR Zero Only

1.23 Providing,fixing,installation and commissioning of RCU 8 Relay Switch + 8 Digital Input, 8 Channel operate separately. Manual Operation enebled.Bus protocol. RCU 8 Relay switch (1 master 20A, 7*relay 10A , 1* 0-10V, 8 Digital inputs). Bus Voltage: 12-32V DC. Protection: Reverse Polarity Protection. as per the direction of engineer incharge. Make: TIS/GM/iCASA or Equivalent.


71

1.24 Providing,fixing,installation and commissioning of DALI 64 Channel Controller Standard DALI connections. Ports: Max 12 no of units. 12 no of Programmabe addresses. 16 group. 16 scenes. Ports-Standard DALI connection Numbers of units max 12 units.as per the direction of engineer incharge. Make: TIS/GM/iCASA or Equivalent.


1.25 Providing,fixing,installation and commissioning of DALI 4 Ch 8 Amp /4 * 700ma, Driver Manual /automatically DALI address setting. DALI address digital indicate.Four channels with four different addresses,4 channels work separately. Compatible with SR-2400TL,SR-2400TG,SR 2400TS,SR-2400LC,SR-2400GC,SR-2400SC and any good quality.as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.26 Providing,fixing,installation and commissioning of 6 Channel Leading Edge Dimmer with 2 Amp each channel. 12to 32 Volt dc. 6 internal fuses. Reverse polarity protection. Manually programmable. 6 channel controlled separately , 12 scenarios, ABS Anti fire material. Manually ON/OFF and Programming. Heat Sink-Aluminum alloy with straight fin. as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.27 Providing,fixing,installation and commissioning of IR Emitter Used to control TV, DVD, etc by sending Infrared code throw the IR probe, Current Sensor up to 2 Amps.Internal logic for judging the Appliances ON or OFF.. Can save up to 250 codes. UL USA certified terminal, ICs and PCB. as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.28 Providing,fixing,installation and commissioning of IR sensor with PIR motion sensor, Light intensity sensor, Infrared control, 2 digital inputs, 12 volt outputs, 32 logic lines, used for saving energy, AV control security and automation.as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.29 Providing,fixing,installation and commissioning of IP Port with RS232, RS485 Ports used for programming , controlling 3rd party device, and to connect free IOS IPhone I pad and android free application. as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.30 Providing,fixing,installation and commissioning of touch panel with TFT screen 4.3". Controls minimum 18 point to point circuits in

each room. Has a AC page.Can control TV and DTH. Has a moods page to plan scenarios. Can be programmed by hand.as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent


1.31 Providing,fixing,installation and commissioning of Wifi IR Eitter with 2 digital inputs.as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.32 Providing,fixing,installation and commissioning of Bus Couplar Need to be connected behind the panel to make it work with additional 3 digital inputs and 12 Volt output.as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.33 Providing,fixing,installation and commissioning of Wifi to Bus Convertor as per the direction of engineer incharge.. Make:TIS/GM/iCASA or Equivalent.


72

1.34 Providing,fixing,installation and commissioning of timer module with built in time clock with central.DTS day time adjustment. Logic Lines: Total 960 logic lines: 240 Tables, each 4 Logic lines. Logic Commands: Simplified logic commands like: (if, or, nand, nor +255 Flags) - Upgrade IO : 1 x mini USB port (to connect to special programming board) - Operation Protection : Polarity Protection • BUS Short Circuit Protection - TIS BUS DC Supply : 24VDC with flexible tolerance between 8-32VDC. - Power consumption: 15mA. as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.35 Providing,fixing,installation and commissioning of Din rail Power supply 24 Volt DC 1.5 Amps t give all Devices its 24 volt power as per the direction of engineer incharge.. Make:TIS/GM/iCASA or Equivalent.


1.36 Providing,fixing,installation and commissioning of Compliant with standards: FBI IAFIS-IQS Appendix F, ANSI-NIST - Resolution: 500 dpi (horizontal and vertical) - Dimension (L*W*H): 14x12.5x15.1cm (5.5x4.9x5.9”) - Slap print size 7,8 x 8,8cm (3.1 x 3.5”) - Rolled print size 3,8 x 4cm (1.5x1.6”) - Weight 1.9kg (4.18 lb) - EMC/Safety standards: CE, FCC - RoHS compliant - The terminal has a MTBF in excess of 50,000 hours etc.complete, as per the direction of engineer incharge. Make :Morpho/MANTRA/ESSL or Equivalent.


1.37 Providing, fixing,installation and commissioning of minimum 5MP fixed dome camera,Image Sensor 1/2.8″ Progressive Scan CMOS,Min. Illumination Color: [email protected] and B/W: 0Lux with IR on,Lens [email protected],WDR (Wide Dynamic Range) 120dB Super WDR,IR Distance 25 Meters ,Primary Stream Video 20fps@(2592x1944), 30fps@(1920x1080, 1280x960, 1280x720, 704x576),Video Compression H.265+/H.265(HEVC)/H.264+/H.264/MJPEG,1*RJ45 10M/100M Ethernet Port as per the direction of engineer incharge. Make : Axis /Milestone/Bosch or Equivalent..


1.38 Providing,fixing,installation and commissioning of minimum 32channel NVR ,Dual Stream Support, Recording Resolution 12MP/8MP/6MP/5MP/4MP/3MP/1080P/UXGA/720P/D1/VGA/CIF/QCIF,HDMI Output 2-CH, Resolution: 3840x2160/60Hz(HDMI1 Only), 3840x2160/30Hz(HDMI1 Only), 1920x1080/60Hz, 1920x1080/50Hz, 1280x1024/60Hz,1280x720/60Hz, 1024x768/60Hz HDMI Supports Audio Output,VGA Output 2-CH, Resolution: 1920x1080/60Hz, 1920x1080/50Hz, 1280x1024/60Hz, 1280x720/60Hz, 1024x768/60Hz,Video Compression H.265+/H.265(HEVC)/H.264+/H.264,Audio Compression G.711/AAC,Storage: 8*SATA HDD (3.5”), 1*eSATA, Up to 10TB capacity for each HDD,Recording type with Continuous, Motion Detection, Alarm, Smart Event, Event (Motion Detection, Alarm, Smart Event).2*RJ45 100M/1000M Network ports .The NVR should be of same make as of cameras as per the direction of engineer incharge.. Make : Axis /Milestone/Bosch /or Equivalent.


73

1.39 Providing,fixing,installation and commissioning of4 TB storage device as per the direction of engineer incharge. Make : SEAGATE/WD/SAMSUNG or Equivalent.


1.40 Providing,fixing,installation and commissioning of 4 pair PVC insulated copper conductor un-armoured Cat-6 computer cable FR in existing surface / concealed steel / PVC conduit / Casing-N-Capping as required.complete, as per the direction of engineer incharge. Make : D-LINK /INTEX/ FINOLEX or Equivalent.

1.040 1000.000 Meter 0.00 0.00 INR Zero Only

1.41 Providing,fixing,installation and commissioning of HDMI Cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.


1.42 Providing,fixing,installation and commissioning of POE switch as per the direction of engineer incharge.. MAKE :Dlink/Cisco/Netgear or Equivalent.


1.43 Providing,fixing,installation and commissioning of 55 " display,Resolution 1920x1080,Aspect Ratio 16:9,Brightness (cd/m2)450,Colour 16.7M,Viewing Angle 178°,Contrast Ratio 4000:1,Video HDMI, VGA, BNC,Control RS-232,Speaker Type 5W, 8Ω (x2),Operating Temperature 0°C to 50°C complete with all accessories as required as per the direction of engineer incharge.. MAKE :Christie/Newline/Allsee Technologies/or Equivalent.


1.44 Providing, fixing,installation and commissioning of Ceiling mount for projector .etc.complete, as per the direction of engineer incharge. Make :NB/AVC/ LOGIC /AV Space or Equivalent.


1.45 Providing,fixing,installation and commissioning of Mixing amplifier 240W @ 100V / 70V /4Ω, 2 mic / line inputs, 4 Music Input, 4-level priority, 24VDC Output for priority over-ride , blackcomplete, as per the direction of engineer incharge. Make : Bose /APART/ Martin Audio / L-Acoustic or Equivalent.


1.46 Providing,fixing,installation and commissioning of 6.5" design cabinet loudspeaker, 100v/60Watts or 16ohm/150Watts, Clickmount wall bracket and safety chain included, etc.complete, as per the direction of engineer incharge. Make : Bose /APART/ Martin Audio / L-Acoustic or Equivalent..


1.47 Providing,fixing,installation and commissioning of Wireless Lapel microphone with bodypack transmitter and cardioid clip-on microphonecomplete, True diversity half-rack receiver in a full-metal housing with intuitive LCD display,Up to 20 compatible channels,Up to 42 MHz bandwidth with 1680 selectable frequencies,Transmission Range: up to 100 meters / 300 feet,High RF output power (up to 30 mW) etc complete as per the direction of engineer incharge. Make : AKG / Sennheiser/Shure / EV or Equivalent.


1.48 Providing,fixing,installation and commissioning of wall mount/flush mount signal plate with HDMI and VGA connectivity with backbox arrangement etc.complete, as per the direction of engineer incharge. Make : Extron/Crestron/AV Space or Equivalent


1.49 Providing,fixing,installation and commissioning of AV equipment rack 4 U complete, as per the direction of engineer incharge. Make : Comrack/INET/AV Space or Equivalent.



1.050 2.000 set 0.00 0.00 INR Zero Only

Total in Figures



INR Zero Only

74

Annexure-F


Name of Work: Providing and Installation complete of ELV system, Gadgets Palm impression, CCTV, Projectors, Projector Screens etc. including related allied works and maintenance of same in RRNMU Building.

Contract No: MP-14 RRNMU/GWL/03, MP-17 RRNMU/IND/03, MP-32 RRNMU/RW/03, MP-33 RRNMU/SG/03, MP-43 RRNMU/UJ/03


PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders

are allowed to enter the Bidder Name and Values only )



Sl. No.


Quantity Units BASIC RATE In Figures ,

including all taxes except GST, To be

entered by the Bidder in Rs. P


amount quoted in Col. 6), To be entered by the

Bidder in Rs. P



Amount in words

1 2 3 4 5 6 7 8 9 10

1 Providing and Installation complete of ELV system, Gadgets

Palm impression, CCTV, Projectors, Projector Screens etc.


RRNMU Building.

1.01 Providing, fixing,installation and commissioning of DLP Projector with , 4,500 lumens, 16:10 Native, 16:9 and 4:3 Compatible, Contrast Ratio 20,000:1, WXGA resolution,Single 0.65″ WXGA DC3 DMD chip DLP Technology,Displayable Colors -1.07 billion,Audio -10W speaker,Inputs -HDMI v1.4a, two VGA-in,composite video, two audio-in, VESA 3D Sync port, RS-232C, RJ45 & mini USB-B,Keystone Correction -± 40° Vertical,Outputs -VGA out, audio out, (3.5mm) etc.complete, as per the direction of engineer incharge. Make : EPSON/Optoma / Infocus or Equivalent.


1.02 Providing, fixing,installation and commissioning of Motorized lift for projector ,Projector lift is powered by strong tubular motors,loading capacity 20 KG,voltage 220V,come complete with spider projector bracket suitable for all projectors,RF remote control.etc.complete, as per the direction of engineer incharge. Make :SUVIRA/LIBARTY/ LOGIC /AV Space or Equivalent.


75

1.03 Providing,fixing,installation and commissioning of Motorized Projection Screen with RF Remote Control Type – Motorized Size(HxW) – 8 feet X10 feet ,wide angle vision,black masking border to get best image quality,inbuilt electric motor 220V. etc.complete, as per the direction of engineer incharge. Make : Star Screen / Liberty/SUVIRA/AV Space or Equivalent.


1.04 Providing,fixing,installation and commissioning of Dual Channel Power Amplifier 2 X 120 Watts @ 100V / 4 Ω, Bridge Mode 1 X 240 Watts @ 100V / 8 Ω , Class D Amp Topology , Convection Cool, 1 U 19" Rackmount etc.complete, as per the direction of engineer incharge. Make : Bose /APART/ Martin Audio / L-Acoustic/Ahuja/Sony or Equivalent.


1.05 Providing,fixing,installation and commissioning of Design cabinet speaker, 5.25" coated paper cone woofer + 1" silk dome tweeter, 100v/30Watts or 16Ω/80Watts,etc.complete, as per the direction of engineer incharge. Make : Bose /APART/ Martin Audio / L-Acoustic/Ahuja or Equivalent.


1.06 Providing,fixing,installation and commissioning of Audio DSP having balanced mic inputs, 2 balanced Mic/Line inputs and 1 stereo unbalanced input, 1 stereo and 2 mono outputs,2-channel USB audio interface for soft codec, integration or playback from computer,Full digital processing on inputs and outputs,8 x 3 audio routing matrix,6-channel Smart Mix (gate or gain sharing),etc.complete, as per the direction of engineer incharge. Make : Sennheiser/Audio technica/Extron or Equivalent hnica/Extron or Eq


1.07 Providing,fixing,installation and commissioning of Wireless handheld microphone set , Up to 12 compatible channels, External antennas, True diversity receiver with metal housing, Automatic frequency management , AF frequency response, 80-14,000 Hz, Switching bandwidth up to 24 MHz, Operating time approx. 10 hrs,Pick-up pattern cardioid etc.complete, as per the direction of engineer incharge. Make : AKG / Sennheiser/Shure / EV or Equivalent.


1.08 Providing,fixing,installation and commissioning of short microphone stand , as per the direction of engineer incharge. Make : Ahuja/K&M/AVSpace or Equivalent.


1.09 Providing,fixing,installation and commissioning of Wireless Lavalier microphone set, Up to 12 compatible channels, External antennas, True diversity receiver with metal housing, Automatic frequency management , AF frequency response, 50 to 16,000 Hz, Switching bandwidth up to 24 MHz, Operating time approx. 10 hrs,Pick-up pattern omnidirectional etc.complete, as per the direction of engineer incharge. Make : AKG / Sennheiser/Shure / EV or Equivalent.


76

1.1 Providing,fixing,installation and commissioning of 65" touch LED display;Panel resolution 1920x1080p;contrast ratio 5000:1,aspect ratio 16:9,brightness 500cd/m2,lifetime -minimum 80000 hours,viewing angle 178 degrees,16.7 M colours,Wireless mirroring,free annotating software,10 point infrared touch technology,stylus set,USB Screen Projection Dongle,Inputs-DisplayPort, Touch USB,HDMI x 2, VGA, Audio In, USB 3.0 x 2, AV In, YPbPr, SD Card,RS 232,Output-AV Out, Audio Out, SPDI,OPERATING HUMIDITY 10% to 80%,OPERATING TEMPERATURE 0°C to 50°C,CPU ARM Quad-core Cortex-A53 1.4GHz ,USB 3.0 x 2, USB 2.0 x3,LAN 10/100 Ethernet,WI-FI 802.11b/g/n/ac,OSAndroid 5.0.1 complete with all accessories as required. , as per the direction of engineer incharge. Make : Christie/Newline/Allsee Technologies/Barco or Equivalent.


1.11 Providing,fixing,installation and commissioning of Indigeneous Digital Lectern in Metallic Frame : Providing & Fixing of Built-in 19” Interactive Panel with motorized tilting, 1xGooseneck Microphone, Top Control Panel VGA, HDMI, USB x 2, Power, VGA Switcher connectivity, built-in 19" Rack for amplifier,CPU. etc.complete, as per the direction of engineer incharge. Make : UNI / Tecom / Peoplelink/AVSPACE or Equivalent.


1.12 Providing,fixing,installation and commissioning of video conference system with 9 party (1+8) MCU, 12X optical

zoom camera,Wi-Fi, Bluetooth, SIP / VoIP & H.323, Android based supporting Skype,VC Recording feature,minimum 3 HDMI Display out,Presentation sharing etc complete, as per the direction of engineer incharge. Make : Polycom/Grandstream/Cisco or Equivalent.


1.13 Providing,fixing,installation and commissioning of hidden Connection Box, Mechanical Locking Device, Smooth Pneumatic Support Structure, VGA with Audio, HDMI, Network / Telephone, Power , Neat & elegant topside, Input voltage: 110V-220V / 50-60Hx, RCA, 3.5 mm Audio Jack, USB, Surface Mountable Enclosure for Cables etc.complete, as per the direction of engineer incharge. Make : Extron/Crestron/AV Space or Equivalent.


1.14 Providing,fixing,installation and commissioning of AV equipment rack 12U complete, as per the direction of engineer incharge. Make : Comrack/INET/AV Space or Equivalent.


1.15 Providing,fixing,installation and commissioning of 2-core loudspeaker cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.015 100.000 Mtr 0.00 0.00 INR Zero Only

1.16 Providing,fixing,installation and commissioning of 2-core Mic Cable.etc.complete, as per the direction of engineer incharge.Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.016 100.000 Mtr 0.00 0.00 INR Zero Only

1.17 Providing,fixing,installation and commissioning of RGB Cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.

1.017 100.000 Mtr 0.00 0.00 INR Zero Only



77





1.21 Providing,fixing,installation and commissioning of Lan CAT6 cable etc.complete, as per the direction of engineer incharge. Make : Dlink/Panduit/AMP or Equivalent

1.021 1.000 set 0.00 0.00 INR Zero Only


1.022 1.000 set 0.00 0.00 INR Zero Only

1.23 Providing,fixing,installation and commissioning of RCU 8 Relay Switch + 8 Digital Input, 8 Channel operate separately. Manual Operation enebled.Bus protocol. RCU 8 Relay switch (1 master 20A, 7*relay 10A , 1* 0-10V, 8 Digital inputs). Bus Voltage: 12-32V DC. Protection: Reverse Polarity Protection , as per the direction of engineer incharge. . Make: TIS/GM/iCASA or Equivalent.


1.24 Providing,fixing,installation and commissioning of DALI 64 Channel Controller Standard DALI connections. Ports: Max 12 no of units. 12 no of Programmabe addresses. 16 group. 16 scenes. Ports-Standard DALI connection Numbers of units max 12 units, as per the direction of engineer incharge. . Make: TIS/GM/iCASA or Equivalent.


1.25 Providing,fixing,installation and commissioning of DALI 4 Ch 8 Amp /4 * 700ma, Driver Manual /automatically DALI address setting. DALI address digital indicate.Four channels with four different addresses,4 channels work separately. Compatible with SR-2400TL,SR-2400TG,SR 2400TS,SR-2400LC,SR-2400GC,SR-2400SC and any good quality , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


1.26 Providing,fixing,installation and commissioning of 6 Channel Leading Edge Dimmer with 2 Amp each channel. 12to 32 Volt dc. 6 internal fuses. Reverse polarity protection. Manually programmable. 6 channel controlled separately , 12 scenarios, ABS Anti fire material. Manually ON/OFF and Programming. Heat Sink-Aluminum alloy with straight fin , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


1.27 Providing,fixing,installation and commissioning of IR Emitter Used to control TV, DVD, etc by sending Infrared code throw the IR probe, Current Sensor up to 2 Amps.Internal logic for judging the Appliances ON or OFF.. Can save up to 250 codes. UL USA certified terminal, ICs

and PCB , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


78

1.28 Providing,fixing,installation and commissioning of IR sensor with PIR motion sensor, Light intensity sensor, Infrared control, 2 digital inputs, 12 volt outputs, 32 logic lines, used for saving energy, AV control security and automation , as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.29 Providing,fixing,installation and commissioning of IP Port with RS232, RS485 Ports used for programming , controlling 3rd party device, and to connect free IOS IPhone I pad and android free application , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


1.30 Providing,fixing,installation and commissioning of touch panel with TFT screen 4.3". Controls minimum 18 point to point circuits in each room. Has a AC page.Can control TV and DTH. Has a moods page to plan scenarios. Can be programmed by hand , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent


1.31 Providing,fixing,installation and commissioning of Wifi IR Eitter with 2 digital inputs , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


1.32 Providing,fixing,installation and commissioning of Bus Couplar Need to be connected behind the panel to make it work with additional 3 digital inputs and 12 Volt output , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


1.33 Providing,fixing,installation and commissioning of Wifi to Bus Convertor , as per the direction of engineer incharge. . Make:TIS/GM/iCASA or Equivalent.


1.34 Providing,fixing,installation and commissioning of timer module with built in time clock with central.DTS day time adjustment. Logic Lines: Total 960 logic lines: 240 Tables, each 4 Logic lines. Logic Commands: Simplified logic commands like: (if, or, nand, nor +255 Flags) - Upgrade IO : 1 x mini USB port (to connect to special programming board) - Operation Protection : Polarity Protection • BUS Short Circuit Protection - TIS BUS DC Supply : 24VDC with flexible tolerance between 8-32VDC. - Power consumption: 15mA. , as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


1.35 Providing,fixing,installation and commissioning of Din rail Power supply 24 Volt DC 1.5 Amps t give all Devices its 24 volt power. as per the direction of engineer incharge. Make:TIS/GM/iCASA or Equivalent.


79

1.36 Providing,fixing,installation and commissioning of Compliant with standards: FBI IAFIS-IQS Appendix F, ANSI-NIST - Resolution: 500 dpi (horizontal and vertical) - Dimension (L*W*H): 14x12.5x15.1cm (5.5x4.9x5.9”) - Slap print size 7,8 x 8,8cm (3.1 x 3.5”) - Rolled print size 3,8 x 4cm (1.5x1.6”) - Weight 1.9kg (4.18 lb) - EMC/Safety standards: CE, FCC - RoHS compliant - The terminal has a MTBF in excess of 50,000 hours etc.complete, as per the direction of engineer incharge Make :Morpho/MANTRA/ESSL or Equivalent.


1.37 Providing, fixing,installation and commissioning of minimum 5MP fixed dome camera,Image Sensor 1/2.8″ Progressive Scan CMOS,Min. Illumination Color: [email protected] and B/W: 0Lux with IR on,Lens [email protected],WDR (Wide Dynamic Range) 120dB Super WDR,IR Distance 25 Meters ,Primary Stream Video 20fps@(2592x1944), 30fps@(1920x1080, 1280x960, 1280x720, 704x576),Video Compression H.265+/H.265(HEVC)/H.264+/H.264/MJPEG,1*RJ45 10M/100M Ethernet Port as per the direction of engineer incharge. Make : Axis /Milestone/Bosch or Equivalent..


1.38 Providing,fixing,installation and commissioning of minimum 32channel NVR ,Dual Stream Support, Recording Resolution 12MP/8MP/6MP/5MP/4MP/3MP/1080P/UXGA/720P/D1/VGA/CIF/QCIF,HDMI Output 2-CH, Resolution: 3840x2160/60Hz(HDMI1 Only), 3840x2160/30Hz(HDMI1 Only), 1920x1080/60Hz, 1920x1080/50Hz, 1280x1024/60Hz,1280x720/60Hz, 1024x768/60Hz HDMI Supports Audio Output,VGA Output 2-CH, Resolution: 1920x1080/60Hz, 1920x1080/50Hz, 1280x1024/60Hz, 1280x720/60Hz, 1024x768/60Hz,Video Compression H.265+/H.265(HEVC)/H.264+/H.264,Audio Compression G.711/AAC,Storage: 8*SATA HDD (3.5”), 1*eSATA, Up to 10TB capacity for each HDD,Recording type with Continuous, Motion Detection, Alarm, Smart Event, Event (Motion Detection, Alarm, Smart Event).2*RJ45 100M/1000M Network ports .The NVR should be of same make as of cameras as per the direction of engineer incharge. .Make : Axis /Milestone/Bosch /or Equivalent.


1.39 Providing,fixing,installation and commissioning of4 TB storage device as per the direction of engineer incharge. Make : SEAGATE/WD/SAMSUNG or Equivalent.


1.40 Providing,fixing,installation and commissioning of 4 pair PVC insulated copper conductor un-armoured Cat-6 computer cable FR in existing surface / concealed steel / PVC conduit / Casing-N-Capping as required.complete, as per the direction of engineer incharge. Make : D-LINK /INTEX/ FINOLEX or Equivalent.

1.040 1000.000 Meter 0.00 0.00 INR Zero Only

1.41 Providing,fixing,installation and commissioning of HDMI Cable etc.complete, as per the direction of engineer incharge. Make : Klotz / Belden / Kramer/Falcon or Equivalent.


80

1.42 Providing,fixing,installation and commissioning of POE switch as per the direction of engineer incharge. . MAKE :Dlink/Cisco/Netgear or Equivalent.


1.43 Providing,fixing,installation and commissioning of 55 " display,Resolution 1920x1080,Aspect Ratio 16:9,Brightness (cd/m2)450,Colour 16.7M,Viewing Angle 178°,Contrast Ratio 4000:1,Video HDMI, VGA, BNC,Control RS-232,Speaker Type 5W, 8Ω (x2),Operating Temperature 0°C to 50°C complete with all accessories as required as per the direction of engineer incharge. . MAKE :Christie/Newline/Allsee Technologies/or Equivalent.


Total in Figures



INR Zero Only

81

Annexure G

SAMPLE FORMAT FOR EVIDENCE OF ACCESS TO OR AVAILABILITY OF CREDIT

FACILITIES

BANK CERTIFICATE

Package No. ………………….

This is to certify that M/s …………………is a reputed company with a good financial standing.

If the contract for the work, namely…………………Package No.------------ is awarded to the

above firm, we shall be able to provide overdraft/credit facilities to the extent of

Rs………………..…to meet their working capital requirements for executing the above Contract.

Signature of Senior Bank Manager…………………….

Name of the senior Bank Manager………………..

Address of the Bank……………………………

Stamp of the Bank

Note : Certificate should be on the letter head of the Bank and phone, fax and e-mail address should

be written clearly.