design and optimization of three field …eprints.uthm.edu.my/8017/1/zhafir_aizat_husin.pdf ·...
TRANSCRIPT
DESIGN AND OPTIMIZATION OF THREE FIELD EXCITATION FLUX SWITCHING MOTORS
FOR HYBRID ELECTRIC VEHICLES
ZHAFIR AIZAT HUSIN
THESIS SUBMITTED IN PARTIAL FULFILMENT OF THE REQUIREMENT
FOR THE AWARD OF THE DEGREE OF MASTER OF ENGINEERING
FAKULTI KEJURUTERAAN ELEKTRIK DAN ELEKTRONIK
UNIVERSITI TUN HUSSEIN ONN MALAYSIA
2015
CHAPTER 1
INTRODUCTION
1.1 Introduction
Hybrid Electric Vehicles (HEV), by means of merge of an Internal Combustion
Engine (ICE) plus another electric traction motors are mostly consider as the
primarily proficient green vehicles. DC machines, induction machines (IMs), switch
reluctance machines (SRMs), and interior permanent magnet synchronous machines
(IPMSMs) are the four major types of electric machines as potential candidates for
HEV drives as depicted in Figure 1.1. DC motors have been familiar in electric
propulsion because their torque–speed characteristics suit the traction requirements
well and their simple control. In the advanced research, the brushes are replaced with
slippery contacts since the DC motor requires high maintenance mostly because of
the mechanical commutator (brush). Nevertheless, DC motor is unfavorable because
this kind of motor comes out with huge structure, low reliability and low efficiency
[1-3].
IM drive is mainly established machinery between assorted brushless motor
drives. Cage IMs are largely acknowledged as the most potential contestant due to
their ruggedness, consistency, low cost, low maintenance and capability to function
in unreceptive environments [4]. Conversely, IM drives encompass drawbacks for
example low efficiency, high loss, low inverter-usage factor and low power factor
which are more concern for the large power and high power motor and that pressed
them away from the battle of HEVs electric propulsion system [5].
SRMs are familiarly known to have a possible potential for HEV
applications. SRMs have exact benefits for instance rugged and simple configuration,
outstanding torque-speed characteristics, low manufacturing cost and simple control
but several drawbacks for HEV applications outweigh the bonus such as torque
2
ripple and acoustic noise generation. The benefits and drawbacks point out above are
relatively important for drive applications [6-7].
(a) (b)
(c) (d)
Figure 1.1: Four main candidates of electric machine for HEV drive
(a) DC motor (b) IM (C) SRM (d) IPMSM
In proportion as EVs and HEVs got popular, the increase in annual usage of
rare-earth magnet has enlarged not only the price of Neodymium (Nd), but also
Dysprosium (Dy) which was indispensable to afford the rare-earth magnet with high
coercivity as the additives. This would cause severe concerns such as high cost,
security issues and supply shortage. Therefore, continuous research and development
on electric machines with high power density, vigorous rotor structure as well as
with no rare-earth magnet would be very important.
PMSMs are a competitive challenge to other motors for HEV. Famous
automakers like Lexus, Honda and also Toyota have adopted in their HEVs. In
opposition, the use of these motors have a low impact on the efficiency at the high-
3
speed range due to the enhance amount in iron loss as well as risk of magnetic faults
[8]. The only machine that already installed for HEVs is IPMSM where it has
developed to enhance power density of the machine [9-12]. Despite of fine operated
and superior performances, this machine do not miss approached by deficiency for
instance IPMSM now have complex form and configuration that give difficulty to
undertake the process of optimizing the design of this motor. The use of PM will
result in a constant state of flux and cannot be controlled as well a burden because of
expensive rare earth magnet prices. Thus, field excitation flux switching motor
(FEFSM) with a new form has been created as a new candidate that can address these
problems in which the uses of permanent magnet is totally excluded while the field
excitation coil (FEC) is located on the stator [13-14]. The proposed motor has a
simple and easy structure and it is expected to provide much higher power density
and torque [15-17].
1.2 Problem Statement
There are four major types of electric machines currently used in HEV drives namely
DC machine, induction machine (IMs), permanent magnet synchronous machines
(PMSMs) and also switch reluctance machine (SRMs). However, there exist several
drawbacks in each motor such as unstable current, asynchronous speed, high volume
permanent magnet, and noisy. In addition, the cost of permanent magnet (PM) used
in IPMSM is expensive and this would increase the cost of the vehicles. To
overcome the problems, continuous research and development on electric machines
with no or less rare-earth magnet, stable current, synchronous speed and silent would
be very important.
As one of the candidates a new structures of field excitation flux switching
motor (FEFSM) in which the use of PM is totally excluded and DC FEC is used as
main flux source. In this research, feasibility studies on FEFSM based on 2D-FEA
are examined and the proposed motor weight to be designed is less than 35kg,
resulting in that the proposed FEFSM promises to attain the maximum power density
better when compared to that existing IPMSM.
4
1.3 Objectives
The objectives of this research are:
(i) To design and investigate the operating principle of Three Phase and Single
Phase Field Excitation Flux Switching Motors (FEFSMs) as an alternative
candidate of non-PM machine.
(ii) To analyze various rotor pole configurations for Three Phase and Single Phase
FEFSMs.
(iii) To evaluate the performances of the improved Three Phase and Single Phase
FEFSMs for HEV drives.
1.4 Methodology
Commercial FEA package, JMAG-Designer ver.13.1, released by Japan Research
Institute (JRI) is used as 2D-FEA solver in this research. Various slot pole
combination of FEFSMs are designed, improved and analyzed to meet the
requirements of conventional HEVs. The general work flow of research methodology
is depicted in Figure 1.2 and details are explained as in Chapter 3.
Start
Design & OP
Various slot pole
analysis
Valid?
Yes
No
Yes
No
No
End
Yes
Valid?
Valid?
Deterministic
Optimization Method
Analysis
Part 1
Part 2
Part 3
Figure 1.2: General work flow of research methodology
5
1.5 Scope of work
The scope of work is only simulation assessment and divided into three parts based
on the objectives are listed as follows:
(i) The design restrictions, target specifications and parameters of the proposed
FEFSMs for HEV applications are listed in Table 1.1 are identical with
existing IPMSM used in Lexus RX400h [12-13]. The electrical restrictions
related with the inverter such as maximum 650V, 375V DC bus voltage and
maximum 360A, inverter current are set for three phase and single phase,
respectively. Assuming water jacket system is employed as the cooling
system for the machine, the limit of the current density is set to the maximum
30Arms/mm2 for armature winding and 30A/mm
2 for FEC, respectively. The
outer diameter, the motor stack length, the shaft radius and the air gap of the
main part of the machine design being 264mm, 70mm, 30mm and 0.8mm
respectively. Initially, coil arrangement test is done to investigate the
operating principle of FEFSMs according to conventional three phase and
single phase system, respectively.
Table 1.1: Design Restrictions and Specifications of FEFSMs [12-13]
Items IPMSM 3ϕ FEFSM 1ϕ FEFSM
Max. DC-bus voltage inverter (V) 650 650 375
Max. inverter current (Arms) 360 360 360
Max. current density in armature winding, JA (Arms/mm2) 30 30 30
Max. current density in excitation winding, JE (A/mm2) NA 30 30
Stator outer diameter (mm) 264 264 264
Motor stack length (mm) 70 70 70
PM weight (kg) 1.1 0 0
Air gap length (mm) 0.8 0.8 0.8
Maximum speed (r/min) 12,400 >12,400 >12,400
Maximum torque (Nm) 333 >210 >70
Maximum power (kW) 123 >123 >41
Machine weight (kg) 35 <35 <35
Power density (kW/kg) 3.5 >3.5 >1.17
(ii) The performances of FEFSMs for three phase and single phase at various
rotor poles are analyzed at open circuit condition and short circuit condition
such as coil test, flux linkage, induced voltage, cogging torque, toque and
power.
6
(iii) The best selected slot pole combination such as 12S-14P, 8S-4P and 8S-8P
are improved and optimized by using deterministic optimization method until
the targeted torque more than 210Nm (three phase) and 70Nm (single phase)
while power more than 123kW (three phase) and 41kW (single phase),
respectively are achieved.
1.6 Thesis outlines
This thesis deals with the design studies on field excitation flux switching motor
(FEFSM) for HEV applications. The thesis is divided into 5 chapters and the
summary of each chapter are listed as follows:
(i) Chapter 2: Review on Flux Switching Motor (FSM)
The second chapter describes some introduction and classifications of FSM
including the example of FEFSM, the operating principle and the proposed
FEFSM for HEV applications.
(ii) Chapter 3: Design of FEFSM for HEV applications
The third chapter describes the design restrictions & specifications of the
proposed FEFSM with similar restriction and specifications of IPMSM used in
HEV are examined using commercial 2D-FEA, JMAG-Studio ver. 13.1,
released by JSOL Corporation. Some equations are listed to find the suitable
slot pole combinations, to set the end time and also frequency for each
combinations, respectively.
(iii) Chapter 4: Performances analysis of FEFSMs
This chapter is divided into three parts. The operating principle and the initial
design configuration are explained in Part 1. Part 2 expained the performances
at various slot pole combinations of three phase and single phase, respectively.
Since the initial performances of output torque and power are far from the
target requirements of 210Nm, 123kW for three phase and 70Nm, 41kW for
single phase, design improvements using “deterministic optimization method”
to treat several design parameters for 12S-14P, 8S-4P and 8S-8P are conducted
until the target performances are achieved. The comparison between the initial
and final design of FEFSMs are discussed in Part 3. The improved design not
7
only successfully achieved the target performances with much higher power
and torque density, but also obtained much higher mechanical strength which is
strong enough to operate at maximum speed of 20,000r/min.
(iv) Chapter 5: Conclusion
The final chapter describes and concludes the summary of the research and
pointed out some future works for design improvements. As an example, the
size of the motor could be reduced to decrease the weight of the machine, thus
increase the power density.
CHAPTER 2
LITERATURE REVIEW
2.1 Introduction to Electric Motor
An electric motor is a device that converts electrical energy into mechanical energy.
Electric motors can be divided into two types which are alternating current (AC)
electric motors and direct current (DC) electric motors as been demonstrated by the
British scientist Michael Faraday in 1821 [18]. Electric motors always associate with
involving rotating coils which are driven by the magnetic force. This force is
produced by a reaction between magnetic field and magnetic current.
Apparently the difference between DC motor and AC motor is AC motors are
powered from alternating current (AC) while DC motors are powered from direct
current (DC), such as batteries, DC power supplies or an AC-to-DC power converter.
Since DC motor’s wound field is constructed with brushes and commutator. The
cost, speed limit and less life expectancy is difficult to overcome.
DC motor should be widely accepted for HEV drives because they can use a
battery as a DC supply as it have an advantage of simple control principle but the
problem which is caused by commutator and brush, make them less reliable and
unsuitable for maintenance-free drives. In contrast, AC induction motors do not use
brushes. They are very rugged and have long life expectancies. Furthermore, the
basic difference between DC and AC motor is speed control. The speed of a DC
motor and AC motor is controlled by varying the armature winding’s current and by
varying the frequency, respectively [19].
AC electric motor can be classified as induction motors (IMs), synchronous
motors (SMs), and switch reluctance motors (SRMs). IM is well suited to
applications requiring constant speed operation. It is made up of the stator, or
stationary winding, and the rotor. It is called “IMs” because the rotor voltage is
induced in the rotor windings instead of physically connected by wires.
9
Furthermore, it is built without the main DC field circuit at all. The distinguishing
feature of IMs is that no DC field current is required to run the motor. It operates on
the basis of interaction of induced rotor currents and the air gap field [20].
The first reference to the term SRMs was made by Nasarin 1969 and the term
became popular from 1980s onwards, through the efforts of the first commercial
exploiters of the technology, Switched Reluctance Drives Ltd. SRMs does not
contain any permanent magnet and the operation of the stator is the same as
brushless DC motor while the rotor is only consist only of laminating iron. The
operation of the SRM where the salient poles tend to align to minimize reluctance in
normal operation leads to high normal forces acting on the stator structure.
Harmonics of these normal forces will resonates the natural frequency resonant
modes of the stator structure thus producing acoustic noise [21].
SMs are AC motors that have a field circuit supplied by an external DC
source. The stator has electromagnets results in the creation of magnetic field which
rotates in time with the oscillations of the line current [20]. SMs can be classified as
permanent magnet (PMSMs), field excitation (FESMs), hybrid excitation (HESM)
and flux switching motor (FSM). FSM can be further classified as permanent magnet
(PM), field excitation (FE) and hybrid excitation (HE). Figure 2.1 illustrates the
classification of main types of Electric Motors.
Figure 2.1: The Classification of the main types of Electric Motors
Electric motor
DC motor AC motor
Induction motor (IM)
Synchronous motor (SM)
Permanent magnet (PM)
Field excitation
(FE)
Hybrid Excitation
(HE)
Flux Switching Motor (FSM)
PMFSM FEFSM HEFSM
Switched reluctance motor (SRM)
10
2.2 Review on electric motors used in HEV
As has been mentioned previously, among different types of electric machines, there
are four main types that are viable for HEVs and are namely, DC machines, IMs,
SRMs and IPMSMs. DC motors have been prominent in electric propulsion because
their torque–speed characteristics suit the traction requirements well, and their
control of the orthogonal disposition of field and armature mmf is simple. Since DC
motor requires high maintenance mainly due to the presence of the mechanical
commutator (brush), as the research advances the brushes are replaced with slippery
contacts. However, DC motor drives have a few demerits such as low efficiency,
bulky construction, and low reliability [1-2].
At the moment, IM drive is the most mature technology among various
brushless motor drives. Cage IMs are broadly established as the most possible
candidate for the electric propulsion of HEVs, due to their ruggedness, reliability,
low cost, low maintenance, and ability to operate in hostile environments. However,
IM drives have demerits such as low efficiency, high loss, low power factor, and low
inverter-usage factor, which are more serious for the high speed and large power
motor and that pushed them out from the race of HEVs electric propulsion system
[5].
Meanwhile, SRMs are gaining much attention and are documented to have a
probable for HEV applications. These motors have specific advantages such as
simple and rugged construction, low manufacturing cost, simple control, and
outstanding torque-speed characteristics. However, several disadvantages for HEV
applications prevail over the advantages. They are acoustic noise generation and
torque ripple. All of the above mentioned advantages and disadvantages are quite
vital for vehicle applications [6-7].
On the other hand, PMSMs are becoming more and more eye-catching and
most proficient of competing with other motors for the electric propulsion of HEVs.
In fact, they are adopted by eminent automakers such as Honda, Toyota, for their
HEVs. However, at a very high speed range, the efficiency may reduce because of
increase in iron loss and also there is a risk of magnetic faults [8].
11
One example of successfully developed electric machines for HEVs is
IPMSM which has been employed primarily to increase the power density of the
machines [9-12]. In spite of their good performances and well operated, IPMSMs
installed in HEV, have some demerits such as the present IPMSM has a multifaceted
shape and structure which are quite complicated to perform the design optimization.
Secondly, the constant flux from PM is hard to control especially at light load high
speed operating points. In the meantime, the volume of PM used in IPMSM is very
high and costly.
2.3 Flux Switching Motor
Generally, the flux switching motor (FSM) can be categorized into three groups that
are permanent magnet flux switching motor (PMFSM), field excitation flux
switching motor (FEFSM), and hybrid excitation flux switching motor (HEFSM).
Both PMFSM and FEFSM has only PM and field excitation coil (FEC), respectively
as their main flux sources, while HEFSM combines both PM and FEC as their main
flux sources. Figure 2.2 illustrates the general classification of FSM.
Figure 2.2: Classification of Flux Switching Motor (FSM)
FSM consists of the rotor and stator. The rotor consist of only single structure
which is iron core thus allowing its simple construction and inherent robustness to be
retained while both field and armature windings are on the stator. These contribute to
major advantages where all brushes are eliminated, whilst complete control is
maintained over the field flux. The operation of the motor is based on the principle of
switching flux. The term “flux switching” is coined to describe machines in which
the stator tooth flux switches polarity following the motion of a salient pole rotor
Flux Switching Motor (FSM)
Permanent Magnet (PM) FSM
Field Excitation (FE) FSM
Hybrid Excitation (HE) FSM
12
[23]. All excitation sources are on the stator with the armature and field allocated to
alternate stator teeth.
Flux is produced in the stator of the machine by permanent magnet or by dc
current flowing in the field winding. The orientation of the field flux is then simply
switched from one set of stator poles to another of stator poles by reversing the
polarity of the current in the armature winding. In the case of inner-rotor flux
switching machines (FSMs) that have been studied, the rotor pole number Nr is
normally designed as close to stator slot number Ns to maximize the performances of
the machine [24].
There is very little study has been carried out, an appropriate number of pole
for the machines must be determined to find the optimal performances. As studied in
[25-26], the analysis has done for Nr ranges from 14 to 26 and Ns is fixed at 12. All of
them concluded their analysis by choosing 12S-22P as the most suitable for the
proposed three-phase outer rotor PMFSM because Nr equal 22 exhibits the highest
back-emf and lowest cogging torque. However, the analysis presented is only focus
on the principle of back-emf and cogging torque characteristic. Other parameters
such as generated magnetic flux, output torque and power also may need to
investigate in order to find the optimal performances and suitable to be further
optimized [27]. As the proposed motor to be applied for HEV applications, the high
torque and power density capability is one of particularly importance parameters
besides of back-emf and cogging torque.
2.3.1 Permanent Magnet Flux Switching Motor
Permanent magnet flux switching motor (PMFSM) is a simple construction. The
stator consists of PM and armature windings and due to this it provides some
advantages such easy cooling of all active parts and better suitability for high speed
applications [28].
PMFSM is popular due to high power density, efficiency and it uses PM to
generate flux. Unfortunately, the generated flux produced is fixed and will not
change-diverged which means it is constant flux because of characteristics of the
PM.
13
As usage of HEV increased, the increase of the usage of rare earth magnet
results in increase of the cost. This would cause serious concern about high cost.
The general operating principle of the PMFSM is illustrated in Figure 2.3,
where the black arrows show the flux line (flux direction) of PM as an example.
From the figure, when the relative position of the rotor poles and a particular stator
tooth are as in Figure 2.3(a), the flux-linkage corresponds to one polarity. However,
the polarity of the flux-linkage reverses as the relative position of the rotor poles and
the stator tooth changes as shown in Figure 2.3(b), i.e., the flux linkage switches
polarity as the salient pole rotor rotates [29].
(a) (b)
Figure 2.3: Principle operation of PMFSM (a) Flux linkage correspond to one
polarity (b) Flux linkage switch polarity as the salient pole rotates [29]
2.3.2 Field Excitation Flux Switching Motor
Field Excitation Flux Switching Motor (FEFSM) is distinct from PMFSM. Instead of
PM it uses FE to generate flux. The stator composed of laminated iron core, armature
coils and DC field excitation coils (FECs) as the only field mmf source. The rotor is
made of only laminated iron core similar with SRM. The external DC source is
applied to produce the magnetic field by make sure that current is flowing through to
the winding.
Armature Coil
Rotor
Stator Stator
14
Even the construction of FEFSM is not simple though PMFSM because of the
external DC source, the good is FEFSM can control flux. Apart from that, there is no
uses of rare-earth magnet resulting in reduce cost-up.
The operating principle of the FEFSM is illustrated in Figure 2.4. Figure 2.4
(a) and (b) show the direction of the FEC fluxes (blue arrow) into the rotor while
Figure 2.4 (c) and (d) illustrate the direction of FEC fluxes into the stator which
produces a complete one cycle flux. Similar with PMFSM, the flux linkage of FEC
switches its polarity by following the movement of salient pole rotor which creates
the term “flux switching”. Each reversal of armature current shown by the transition
between Figures 2.4(a) and (b), causes the stator flux to switch between the alternate
stator teeth [13].
(a) (b)
(c) (d)
Figure 2.4: Principle operation of FEFSM (a) θe=0° and (b) θe=180° flux moves
from stator to rotor (c) θe=0° and (d) θe=180° flux moves from rotor to stator [13]
Armature Coil
Armature Coil
FEC FEC FEC FEC
FEC FEC FEC FEC
15
2.3.3 Hybrid Excitation Flux Switching Motor
Hybrid Excitation Flux Switching Motor (HEFSM) is the combination of PM and
FE. HEFSM has significantly less magnet and higher torque density than those of a
conventional PMFSM. To easily adjust the main flux, which is fixed in PMFSM,
HEFSM were developed to improve the starting/low-speed torque and high-speed
flux-weakening capabilities, which are required for HEV [30].
However, in addition to its inherent relatively low torque density, it has a long
end winding for the field windings, which overlap the armature windings.
Unfortunately, the foregoing hybrid-excited machines having magnets on the stator
also suffer from these disadvantages. Firstly, the DC excitation field is in series with
the field excited by magnets, which limits the flux-adjusting capability due to low
permeability of magnets.
Secondly, the flux path of DC excitation significantly reduces the main flux
excited by magnets and even short circuits the magnet. In the meantime, torque
density may be significantly reduced. In addition, the use of PM will give concern
about cost-up because of the price is expensive. Apart from that, HEFSM usually
have complicated 3-D structure and thus result in difficult to analyze and
manufacture.
The operating principle of the proposed HEFSM is illustrated in Figure 2.5,
where the red and blue line indicate the flux line (flux direction) from PM and FEC,
respectively. In Figure 2.5(a) and (b), since the direction of both PM and FEC fluxes
are in the same polarity, both fluxes are combined and move together into the rotor,
hence producing more fluxes with a so called hybrid excitation flux. Furthermore in
Figure 2.5(c) and (d), where the FEC is in reverse polarity, only flux of PM flows
into the rotor while the flux of FEC moves around the stator outer yoke which results
in less flux excitation [29].
16
(a) (b)
(c) (d)
Figure 2.5: Principle operation of HEFSM (a) θe=0° - more excitation (b) θe=180°
- more excitation (c) θe=0° - less excitation (d) θe=180° - less excitation [29]
2.4 IPMSM Vs FEFSM
Based on the overview and classifications of various FSMs that have been discussed,
PMFSM, FEFSM and HEFSM have their own advantages and disadvantages.
Among the three types of FSM which are PMFSM, FEFSM and HEFSM, FEFSM is
the best type to consider. This is because FEFSMs have many advantages over
disadvantages as compared to both PMFSM and HEFSM. FEFSM do not adopt the
usage of PM because PM is a rare-earth magnet that is costly for practical usage. In
the meantime, IPMSM which has been installed in existing HEV also adopt the
usage of rare-earth PM and possess several drawbacks.
Armature Coil
Armature Coil
17
2.4.1 IPMSM drawbacks
In spite of their good performances and well operated as mentioned in [9-12],
IPMSMs installed in HEV, have some drawbacks to be solved as follows:
(i) The three-phase armature windings are wounded in the form of
distributed windings which results in much copper loss and high coil end
length.
(ii) The mechanical stress of the rotor depends on the number of PM bridges.
High number of bridges not only increases the mechanically weak points
but also causes much flux leakage between the PMs that will degrade the
performance of the machine.
(iii) The present IPMSM has a complex shape and structure which is are
relatively difficult to perform the design optimization.
(iv) The constant flux from PM is difficult to control especially at light load
high speed operating points.
(v) The volume of PM used in IPMSM is very high, more than 1.0kg, which
increases the cost of the machine.
(vi) There are windings at the rotor resulting in not robust rotor structure for
high speed applications.
2.4.2 Research on FEFSM for HEV
Early examples of FEFSM, the three-phase 12S-10P, 12S-8P and 12S-14P FEFSMs
are developed as shown in Figure 2.6 (a), (b) and (c), respectively. The 12S-10P
FEFSM in Figure 2.6 (a) is designed in which the PM is removed from the stator and
half of the armature coil slots in the upper layer are placed with the FEC windings as
explained in [31]. The FEC-1 and FEC-2 are arranged with alternate DC current
source polarity to produce two flux polarities that can give much flux sources.
However, since the isolated and unused stator teeth shown in red circle in Figure 2.6
(a) reduce the performance of the machine, further investigations into improvements
of the machine design of three phase FEFSMs should be made. Next, the 12S-8P
FEFSM is designed with segmental rotor as shown in Figure 2.6 (b) [32]. Whereas
18
segmental rotors are used traditionally to control the saliency ratio in synchronous
reluctance machines (SynRM), the primary function of the segments in this design is
to provide a defined magnetic path for conveying the field flux to adjacent stator
armature coils as the rotor rotates. Unfortunately, the flaws of segmental rotor are
less robust and complicated as compared to salient rotor resulting in not suitable for
high speed applications. As the advance research, 12S-14P FEFSM with non-overlap
winding and salient pole rotor with all stator teeth is used as shown in Figure 2.6 (c)
is designed to achieve higher torque and power density. Regrettably, the fundamental
performance of this design for instance DC FEC flux linkage, has produced low flux
resulting in lower output torque and power as well as high torque ripple [33].
(a) (b)
(c)
Figure 2.6: Example of FEFSMs (a) 3-phase 12S-10P
(b) 3-Phase 12S-8P segmental rotor (c) 3-phase 12S-14P
FEC-1
FEC-2
FEC-1 FEC-2
FEC-2
FEC-1
FEC-2
FEC-2
FEC-1 FEC-1
FEC-2
FEC-1
B1 C1
A1 A1
C1 B1
A1
B1
C1 A1
B1
C1
B1
A1
C1 A1
B1
C1
FEC-1
FEC-2
CHAPTER 3
METHODOLOGY
3.1 Introduction
An analytical study, Finite Element Analysis (FEA) study based on reluctant network
is used to evaluate magnetic flux is needed to design the FEFSM. Using FEA based
on JMAG-Designer Software allows obtaining information that is not available
through an actual device test because it gives us substantially greater insight into the
device's performance. JMAG is simulation software for electromechanical design
striving to be easy to use while providing versatility to support users from conceptual
design to comprehensive analyses. JMAG can accurately capture and quickly
evaluate complex physical phenomena inside of machine [34]. Generally, the project
implementation is divided into 3 parts which are design, analysis and optimization.
The general flow of research methodology is illustrated in Figure 3.1.
Start
Design &
operating principle
Improvement/
Optimization
Performances analysis
End
Part 1
Part 2
Part 3
Figure 3.1: General work flow of project implementation
20
3.2 Part 1: Design and operating principle investigation
In design part, it is divided in 2 portions for instance Geometry editor and JMAG-
Designer. Geometry editor is used to design each part of motor separately such as
rotor, stator, armature coil, and FEC while the materials, conditions, circuit, mesh
setting and simulation are developed by using JMAG-Designer. Electrical steel
35H210 is used for rotor and stator body whereas copper is used for armature coil
and FEC, respectively. The work flows of the motor design are illustrated in Figure
3.2.
Start
Geometry Editor
Sketch of Rotor Sketch of StatorSketch of
Armature coilSketch of FEC
JMAG-Designer
Set the materials Set the conditions Set the circuitsSet the mesh &
study properties
Valid?
Coil Test
Analysis
End
Yes
No
Yes
No
Figure 3.2: Work flow of motor design in Geometry Editor and JMAG-Designer
21
3.2.1 The proposed FEFSM for HEV
In order to overcome the problem of heavy rare earth PM in existing IPMSM,
PMFSM, HEFSM and also initial design of segmental rotor FEFSM and non-overlap
winding, a new structure of 12S-10P FEFSM in which the usage of PM is totally
excluded, replacement of segmental rotor by salient rotor, all stator teeth used and
non-overlap winding is substituted by overlap winding is designed as shown in
Figure 3.3. The novelty of this proposed design are robust rotor structure and suitable
for high speed application for HEV drive with high torque and power capabilities
[12]. In the meantime, the study on various slot pole combinations shall be done to
ensure the best combination of slot plot to give higher output torque and power. The
selections of the initial design FEFSMs are based on the main geometrical
dimensions identical to existing IPMSM in which the stator outer diameter, stack
length and shaft are set respectively to 132mm, 70mm and 30mm with following
assumptions below and design parameters of FEFSMs are shown in Table 3.1.
(i) The initial rotor radius is selected based on rotor radius of general machine of
approximately 60% to 75% of the machine outer radius.
(ii) The FEC and armature coil slot opening angle are set to be half of the stator
slot opening angle.
(iii) The width of both slots is set to be similar along the coil depth. Furthermore,
the total coil slot area of both FEC and armature coil is less than the stator
teeth area so that all fluxes from both coils is expected to have sufficient
space to flow in the stator yoke, without magnetic saturation.
(iv) The stator outer core thickness is set to be half of the stator inner teeth length
with the assumptions that the fluxes are divided into two parts.
(v) The outer rotor pole angle is set by dividing the total stator tooth opening
angle to the number of rotor poles by assuming that all fluxes from stator will
have sufficient space to flow into the rotor. Small rotor pole width will
prevent some amount of flux from the stator to flow to the rotor part,
resulting in flux saturation. In contrast, larger rotor pole width will easily
receive all flux from the stator, but will easily distribute the flux on the rotor
resulting in some of the flux leak or flow unnecessary.
22
(vi) The depth of rotor pole is set to be 1/3 of the rotor radius to give much depth
for the flux to flow while keeping the suitable distance of the rotor inner part
to avoid flux saturation and to keep the acceptable rotor mechanical strength,
simultaneously.
(vii) To ensure flux moves from stator to rotor equally without any flux leakage,
the design of the proposed machine is defined as in Equation 3.1.
Stator Tooth Width = Rotor Tooth Width (3.1)
Figure 3.3: The proposed 12S-10P FEFSM
Table 3.1: Design parameters of FEFSMs
Items 3ϕ FEFSM 1ϕ FEFSM
Rotor radius [mm] 97.2 97.2
Rotor pole width [mm] 16.8 10.3
Rotor pole depth [mm] 33.2 33.2
FEC width [mm] 7.0 8.9
FEC depth [mm] 26 22.02
Armature coil depth [mm] 26 22.02
Armature coil width [mm] 7.0 8.9
Number of turns of armature coil 8 8
3.3 Part 2: Analysis
In the proposed FEFSM, the relationship between the number of rotor pole and stator
slot for the three-phase and single-phase can be express as in Equation 3.2 [35],
A1
B1
C1
FEC-1
FEC-2
A1
A1
A1
B1
B1 B1
C1
C1
C1
23
)2
1(q
kNN sr
(3.2)
where Nr is the number of rotor poles, Ns is the number of stator slots, k is the natural
number, and q is the number of phases. For the proposed motor, q equals to 3 and 1
for three phase and single phase, respectively while Ns equals to 12 for three phase
and 8 for single phase. Lastly, Nr is even numbers that varies from 10, 14, 16, 20, 22
and 4, 8, 12 for three phase and single phase, correspondingly. The work flow of the
analysis part is illustrated in Figure 3.4 and the performances of the FEFSMs at
various rotor pole numbers is analyzed at open circuit and short circuit condition,
respectively.
Start
Part 1
Various slot pole
analysis
No Load Analysis
(open circuit condition)
1. DC FEC flux linkage
2. Flux lines
3. Induced voltage
4. Cogging torque
Load Analysis
(short circuit condition)
1. Torque vs Je/Ja
2. Power vs Je/Ja
Valid?
Best
selected?
End
Yes
No
Yes
No
Figure 3.4: Work flow of motor analysis
24
3.3.1 Open Circuit Condition
In this proposed motor, the motor rotation through 1/Nr of a revolution, the flux
linkage of armature has one periodic cycle and thus, the frequency of back-emf
induced in the armature coil is Nr times of the mechanical rotational frequency. In
general, the mechanical rotation frequency, fm and the electrical frequency, fe for the
proposed three phase machine can be expressed as in Equation 3.3 and end time, T is
calculated using Equation 3.4 while for the proposed single phase machine it can be
expressed as in Equation 3.3 or Equation 3.5 as long as one cycle flux is formed and
end time, T is calculated using Equation 3.4,
mre fNf (3.3)
eFT
1
(3.4)
mre fNf 2 (3.5)
where fe, Nr and fm is the is the electrical frequency, number of rotor poles and
mechanical rotation frequency, respectively. Assuming only one water-jackets
system is employed as a cooling system, the current density threshold is set to be
30Arms/mm2 and 30A/mm
2, respectively, for armature winding and FEC. The number
of turns, N, per armature coil and FEC is defined by Equations 3.6 and 3.7, with the
filling factor of motor, α, set as 0.5.
a
aa
aI
SJN
(3.6)
e
ee
eI
SJN
(3.7)
Where N, J, α, S and I are number of turns, current density, filling factor, slot area
and input current, respectively. For the subscript a and e respectively represent
armature coil and FEC. In open circuit condition (no load analysis), only FEC current
REFERENCES
[1] C. C. Chan, “The state of the art of electric, hybrid, and fuel cell vehicles”,
Proc. IEEE, vol. 95, no. 4, pp.704–718, Apr. 2007.
[2] A. Emadi, J. L. Young, K. Rajashekara, “Power electronics and motor drives
in electric, hybrid electric, and plug-in hybrid electric vehicles”, IEEE Trans.
Ind. Electron., vol.55, no.6, pp.2237-2245, Jan. 2008.
[3] D. W. Gao, C. Mi, and A. Emadi, “Modeling and simulation of electric and
hybrid vehicles”, Proc. IEEE, vol. 95, no. 4, pp. 729–745, April 2007.
[4] C. C. Chan, “The state of the art of electric and hybrid vehicles”, Proc. IEEE,
vol. 90, no. 2, pp. 247–275, Feb. 2002.
[5] T. Wang et al., “Design characteristics of the induction motor used for hybrid
electric vehicle,” IEEE Trans. Magn., vol. 41, no. 1, pp. 505–508, Jan. 2005.
[6] J. Malan and M. J. Kamper, “Performance of a hybrid electric vehicle using
reluctance synchronous machine technology”, IEEE Trans. Ind. Appl., vol.
37, no. 5, pp. 1319–1324, Sep./Oct. 2001.
[7] K. M. Rahman, B. Fahimi, G. Suresh, A. V. Rajarathnam, and M. Ehsani,
“Advantages of switched reluctance motor applications to EV and HEV:
Design and control issues”, IEEE Trans. Ind. Appl., vol. 36, no. 1,
pp. 111– 121, Jan./Feb. 2000.
[8] T. M. Jahns, and V. Blasko, “Recent advances in power electronics
technology for industrial and traction machine drives”, Proc. IEEE, vol. 89,
no. 6, pp. 963–975, June 2001.
[9] K. C. Kim, C. S. Jin, and J. Lee: “Magnetic shield design between interior
permanent magnet synchronous motor and sensor for hybrid electric vehicle”,
IEEE Transaction on Magnetics, vol. 45, no.6 pp.2835–2838, June 2009.
[10] M. Kamiya, “Development of traction drive motors for the Toyota hybrid
systems”, IEEJ Trans. Ind. Appl., vol.126, no.4, pp.473-479, Apr. 2006.
[11] M.A. Rahman: “IPM Motor Drives For Hybrid Electric Vehicles”,
International Aegean Conference on Electrical Machines and Power
Electronics, Sept. 2007.
[12] R. Mizutani: “The present state and issues of the motor employed in Toyota
HEVs”, Proc. of the 29th Symposium on Motor Technology in Techno-
Frontier, 2009.
[13] E. Sulaiman, T. Kosaka, and N. Matsui, “A New Structure of 12Slot-10Pole
Field Excitation Flux Switching Synchronous Machine for Hybrid Electric
Vehicles”, IEEE 14th European Conference on Power Electronics and
Applications, pp. 1-10, Sept. 2011.
[14] E. Sulaiman, N. Matsui and T. Kosaka, “Design Study and Experimental
Analysis of Wound Field Flux Switching Motor for HEV Application”, IEEE
International Conference on Electrical Machines, pp. 1269-1275, Sept. 2012.
[15] E. Sulaiman, T. Kosaka, and N. Matsui, “Design and Analysis of High-
Power/ High-Torque Density Dual Excitation Switched-Flux Machine for
Traction Drive in HEVs”, Renewable & Sustainable Energy Review,
submitted for 3rd review, Jan 2014.
[16] E. Sulaiman, T. Kosaka, N. Matsui, and M. Z. Ahmad, “Design Studies on
High Torque and High Power Density Hybrid Excitation Flux Switching
Synchronous Motor for HEV Applications,” in IEEE International Power
Engineering and Optimization Conference, 2012, pp. 333–338, June 2012.
[17] E. Sulaiman, T. Kosaka, and N. Matsui: “High power density design of 6slot-
8pole hybrid excitation flux switching machine for hybrid electric vehicles”,
IEEE Trans. on Magn., vol.47, no.10 pp. 4453-4456, Oct. 2011.
[18] History of Electric Motor. Access on November 29, 2013
http://en.wikipedia.org/wiki/Electric_motor
[19] Difference between AC and DC Motors. Access on November 29, 2013.
http://www.ohioelectricmotors.com/what-is-the-difference-between-an-ac-
motor-and-a-dc-motor-673#ixzz2CdnjLwIg.
[20] Jerry Bednarczyk, PE, Induction Motor Theory. Access on November 29,
2013. http://www.pdhonline.org/courses/e176/e176content.pdf
[21] Pragasen Pillay & William Cai, An investigation into vibration
in switched reluctance motors. Access on November 29 2013.
http://www.fleadh.co.uk/srm.htm
[22] What is synchronous motor. Access on November 29, 2013.
http://en.wikipedia.org/wiki/Synchronous_motor.
[23] S. E. Rauch and L.J. Johnson, „Design principles of flux-switch alternators‟,
Tans. AIEE, vol. 74 pt. III, pp. 1261-1268, 1955.
[24] J.T. Chen, and Z. Q. Zhu, "Influence of rotor pole number on optimal
parameters in flux-switching PM brushless AC machines by the lumped
parameter magnetic circuit model," IEEE Trans. Ind. Appl. , vol. 46, no. 4,
pp. 1381-1388, Jul/Aug 2010.
[25] Y. Wang, M.J. jin, J. Shen et al, "An outer-rotor flux switching permanent
magnet machine for traction applications," IEEE Energy Conversion
Congress and Exposition, pp. 1723-1730, 2010.
[26] W. Fei, P. Chi, K. Luk, S. Member, J. X. Shen, Y. Wang, and M. Jin, “A
Novel Permanent-Magnet Flux Switching Machine With an Outer-Rotor
Configuration for In-Wheel Light Traction Applications,” IEEE Transactions
on Industry Applications, vol. 48, no. 5, pp. 1496–1506, 2012.
[27] E. Sulaiman and T. Kosaka, “Parameter Sensitivity Study for Optimization of
Field Excitation Flux Switching Synchronous Machine for HEV”, IEEE
Conference on Industrial Electronic and Applications, pp. 52-57, July 2012.
[28] Z. Q. Zhu, and J. T. Chen, “Advanced Flux-Switching Permanent Magnet
Brushless Machines,” IEEE Trans. Magnetics, vol. 46, no.6 pp. 1447–1453,
June 2010.
[29] Zhu, Z.Q: “Switched flux permanent magnet machines: Innovation
continues”, in Proc. Int. Conf. on Electrical Machines and Systems, pp.1-10,
Aug. 2011.
[30] E. Spooner, S. A. W. Khatab, and N. G. Nicolaou, “Hybrid excitation of AC
and DC machines,” in Proc. IEE Int. Conf. Elect. Mach. Drives, pp. 48–52,
Sep. 1989.
[31] J. T. Chen, Z. Q. Zhu, S. Iwasaki, and R. Deodhar: “Low cost flux-switching
brushless AC machines”, IEEE Vehicle Power and Propulsion Conf., VPPC
2010, Lille, France, Sept. 2010.
[32] A. Zulu, B. Mecrow, and A. Armstrong: “A wound-field three-phase flux-
switching synchronous motor with all excitation sources on the stator”, IEEE
Trans. Industry Applications, Vol.46, pp.2363-2371, Nov. 2010.
[33] F. Khan, E. Sulaiman, Z. A. Husin and M. F. Omar, “Performances
Comparison of 12S-14P FEFSM with overlap and non-overlap windings for
HEV”, IEEE Student Conf. Research and Development, pp.1-6, Dec. 2014.
[34] JMAG Software. Access on December 11, 2013
http://www.jmag-international.com/
[35] E. Hoang, M. Lecrivain, and M. Gabsi: “A new structure of a switching flux
synchronous polyphased machine with hybrid excitation”, in Proc. Eur. Conf.
Power Electron. Appl., pp.1–8, Sep. 2007.