d-ej955 c805 c809 r812 r811 r807 vdr8 fb803 d803 k a c440 + ... instruction manual. 4 getting...

SERVICE MANUALVer 1.1 2002.01

SPECIFICATIONS

PORTABLE CD PLAYER

D-EJ955AEP Model

UK ModelE Model

Australian ModelChinese Model

Tourist Model

Model Name Using Similar Mechanism NEW

CD Mechanism Type CDM-3325ES

Optical Pick-up Name DAX-25E

SystemCompact disc digital audio system

Laser diode propertiesMaterial: GaAlAsWavelength: λ = 780 nmEmission duration: ContinuousLaser output: Less than 44.6 µW(This output is the value measured at a distanceof 200 mm from the objective lens surface onthe optical pick-up block with 7 mm aperture.)

D-A conversion1-bit quartz time-axis control

Frequency response20 - 20 000 Hz +1

– 2 dB (measured by JEITA CP-

307)

Output (at 4.5 V input level)Line output (stereo minijack)

Output level 0.7 V rms at 47 kΩRecommended load impedance over 10 kΩ

Headphones (stereo minijack)Approx. 5 mW + Approx. 5 mW at 16 Ω (Approx. 0.5 mW + Approx. 0.5 mWat 16 Ω)**For the customers in France

Optical digital output (optical output connector)Output level: –21 - –15 dBmWavelength: 630 - 690 nm at peak level

Power requirementsFor the area code of the model youpurchased, check the upper left side of thebar code on the package.• Two Son y NC-6WM rechargeable batteries:

2.4 V DC• Two LR6 (size AA) ba tteries: 3 V DC

• AC power adaptor (DC IN 4.5 V jack):AEP, French, East European, E13 models: 220 - 230 V, 50/60 HzUK model: 230 - 240 V, 50 Hz Australian model : 240 V, 50 Hz E33, Korean, Tourist models: 100 - 240 V, 50/60 Hz Hong Kong model: 220 V, 50/60 HzChinese model: 220 V, 50 Hz

Battery life* (approx. hours)(When you use the CD player on a flat and stablesurface.)Playing time varies depending on how the CDplayer is used.

When using G-PROTECTION“1” “ 2”

Two NC-6WM 19 19.5(charged forabout 5 hours**)

External battery case 66 71(two alkaline batteries***)

Rechargeable batteries 88 92NC-6WM andexternal battery case(two alkaline batteries***)

* Measured value by the standard of JEITA(Japan Electronics and Informa tion TechnologyIndustries Association).

** Charging time varies depending on how therechargeable battery is used.

*** When using Sony alkaline ba tteries LR6 (SG)(produced in Japan)

Operating temperature5°C - 35°C (41°F - 95°F)

Dimensions (w/h/d) (excludingprojecting parts and controls)Approx. 135.0 × 135.0 × 15.9 mm (5 3⁄8 × 5 3⁄8 × 21⁄32 in.)

Mass (excluding accessories)Approx. 166 g (5.9 oz)

Design and specifications are subject to changewithout notice.

Supplied accessoriesFor the area code of the location in which youpurchased the CD player, check the upper left sideof the bar code on the package.

AC power adaptor (1)Headphones/earphones with remote control (1)Rechargeable batteries (2)Charging stand (1)Battery carrying case (2)Carrying pouch (1)External battery case (1)AC plug adaptor (1)** Supplied with E33 and tourist models

• AbbreviationE13: 220 - 230 V AC area in E modelE33: 100 - 240 V AC area in E model

9-873-376-02 Sony Corporation2002A0500-1 Personal Audio Company

C 2002.1 Published by Sony Engineering Corporation

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

http://www.xiaoyu163.com





2

D-EJ955

Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 ˚C dur-

ing repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering

or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.

TABLE OF CONTENTS

1. SERVICING NOTES ............................................... 3

2. GENERAL ................................................................... 6

3. DISASSEMBLY3-1. Disassembly Flow ........................................................... 73-2. Upper Lid (A) Sub Assy ................................................. 73-3. Cabinet (Upper) Sub Assy .............................................. 83-4. Main Board, Optical Pick-up Section

(CDM-3325ES) ............................................................... 8

4. ELECTRICAL CHECK .......................................... 9

5. DIAGRAMS5-1. Block Diagram – MAIN Section (1/2) – ....................... 105-2. Block Diagram – MAIN Section (2/2) – ....................... 115-3. Block Diagram – POWER SUPPLY Section – ............. 125-4. Note for Printed Wiring Boards and

Schematic Diagrams ....................................................... 135-5. Printed Wiring Board ...................................................... 145-6. Schematic Diagram – MAIN Board (1/3) – .................. 155-7. Schematic Diagram – MAIN Board (2/3) – .................. 165-8. Schematic Diagram – MAIN Board (3/3) – .................. 175-9. IC Pin Function Description ........................................... 18

6. EXPLODED VIEWS6-1. Upper Lid, Cabinet (Upper) Section .............................. 256-2. Cabinet (Lower) Section ................................................. 266-3. Optical Pick-up Section (CDM-3325ES) ....................... 27

7. ELECTRICAL PARTS LIST ............................... 28

This appliance is classified as a CLASS 1 LASER product.The CLASS 1 LASER PRODUCT MARKING is located onthe rear exterior.

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous ra-diation exposure.

On AC power adaptor• Use only the AC power adaptor supplied or

recommended in “Accessories (supplied/optional).” Do not use any other AC poweradaptor. It may cause a malfunction.

Polarity of the plug

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






3

D-EJ955SECTION 1

SERVICING NOTES

The laser diode in the optical pick-up block may suffer electro-static breakdown because of the potential difference generated bythe charged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.

BEFORE REPLACING THE OPTICAL PICK-UP BLOCKPlease be sure to check thoroughly the parameters as par the “Op-tical Pick-Up Block Checking Procedures” (Part No.: 9-960-027-11) issued separately before replacing the optical pick-up block.Note and specifications required to check are given below.

• FOK output: IC601 yg pinWhen checking FOK, remove the lead wire to disc motor.

• RF signal P-to-P value: 0.4 to 0.6 Vp-p

LASER DIODE AND FOCUS SEARCH OPERATIONCHECKDuring normal operation of the equipment, emission of the laserdiode is prohibited unless the upper lid is closed while turning ONthe S804. (push switch type)The following checking method for the laser diode is operable.

• Method:Emission of the laser diode is visually checked.

1. Open the upper lid.2. With a disc not set, turn on the S801 with a screwdriver having

a thin tip as shown in Fig.1.3. Press the > N button.4. Observing the objective lens, check that the laser diode emits

light.When the laser diode does not emit light, automatic powercontrol circuit or optical pickup is faulty.In this operation, the objective lens will move up and down 4times along with inward motion for the focus search.

NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT

Fig. 1 Method to push the S804

S804

detection lever

detection lever

MAIN board

About CD-Rs/CD-RWsThis CD player can play CD-Rs/CD-RWs recorded in the CD-DAformat*, but playback capability may vary depending on the qual-ity of the disc and the condition of the recording device.* CD-DA is the abbreviation for Compact Disc Digital Audio. It isa recording standard used for the Audio CDs.

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






4

D-EJ955

SERVICE MODEIn the Service mode, this set can check the following.

1. Service Mode Setting MethodTo set the service mode, perform as follows.1) Make sure that the power is not turned on.2) Check for the following states:

Open/close detection switch (S804) ...... OFFSolder bridge at SL806 (OPEN) ............ OPEN[AVLS] switch (S802) ........................... NORM[HOLD] switch (S801) .......................... OFF[G PROTECTION] switch (S803) ....... 1

3) Short the solder bridge at the SL807 (TEST) on the MAINboard (see Fig. 2).

4) Turn the power on.

2. Operation in Service ModeWhen the Service mode is set, the LCD on the remote commanderdisplays the following.

Remote commander LCD display

3. Operation of Buttons and Knobs in Service ModeThe following operation can be checked by operating the buttonsand knobs on the set and remote commander.

3-1 . Case without Setting a CD• > N / . buttons on the set and > N / . knobs on

remote commanderOptical pick-up movement (outward or inward)Tracking/sled servo off

Note: Do not look directly at the laser beam from the optical pick-up.Do not move forcibly the optical pick-up exceeding the most-out-side or most-inside track.

3-2 . Case with Setting a CDCheking method:1) Make sure that the power is not turned on.2) Leave a solder bridge of the SL807 (TEST) on the MAIN board

shorted.3) Turn the power on, and then set a CD and play it with the X

button on the remote commander.

• x button on the set and remote commanderAll servos (focus/tracking/sled) off

• > N / . buttons on the set and > N / . knobs onremote commanderOptical pick-up movement (outward or inward)Tracking/sled servo off

• [PRT/ENT] button on remote commanderTracking gain up mode

• [VOL +] / [VOL --] buttons on the set and [VOL +] / [VOL --]knobs on remote commander2-step volume setting

• [PLAYMODE] button on remote commanderCLV speed becomes 1 to 4 times each time the button is pressedTracking/sled servo on

– MAIN Board (Component Side) –

Service mode

All lit 888

Microcomputerversion display VD101

DDDD

BASS12

Fig. 2

R813

R808

C811C8

10

C804

C807C805 C809

R812R811

R807

VDR8FB80

3

D803

K

A A

C440

+

C464

C806+

D805

SL806(OPEN)

SL807(TEST)

•

0000

Remote Commander LCD display

(play mode)


(For the rest, turn the power off and then turn it on again)

Up0000

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






5

D-EJ955

• [SOUND] button on remote commanderServo auto adjustment

4.Service Mode Releasing MethodTo release the service mode, perform as follows.1) Turn the power off.2) Open the solder bridge at the SL807 (TEST) on the MAIN

board.Note: Remove the solder completely.

5.Error Rate Check DisplayThe C1 error rate check display mode becomes active if the fol-lowing operation is performed during the operation in the normalmode.1) Turn the power off, and cancel other service operations.2) Turn the power on, and then set a CD and play it with the X

button on the remote commander.

3) Press the [SOUND] button on the remote commander to makeautomatic adjustment.

4) Press the [PLAY MODE] button on the remote commander.

5) Press the [DISPLAY] button on the remote commander, andthe C1 error rate display will be activated and the LCD on theremote commander will display as follows.

Note: In the play state, press the [SOUND] button on the remote com-mander before pressing the [PLAY MODE] button. Wrong order ofbutton operations will result in very large Er**** value.

6) Turn the power off.7) Open the solder bridges at the SL807 (TEST) on the MAIN

board.Note: Remove the solder completely.


(1 time)010001

(4 times)040004

(For the rest, turn the power off and then turn it on again)

0000



010001

Remote Commander LCD display**** value0000 to 0099 : OKmore than 0100 : NG

Er****

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






6

D-EJ955SECTION 2GENERAL

This section is extracted frominstruction manual.

4

Getting started

Locating the controlsFor details, see pages in parentheses.

CD player (front)

CD player (inside)

4x (stop) /CHARGE button•CHARGE lamp(pages 8, 15, 16, 19, 20)

6i (headphones) jack(page 7)

9AVLS switch(page 15)

1 EXT BATT (external battery)/DC IN 4.5 V (external powerinput) jack (pages 7, 20, 22)

3VOL (volume) +*/– buttons(page 8)

2 LINE OUT (OPTICAL) jack(page 17)

qsHOLD switch(page 15)

7OPEN switch(page 7)

8 Terminals for the charging stand(pages 19, 25)

qaBatterycompartment(page 19)

CD player (rear)

q;G-PROTECTIONswitch(page 13)

5.(AMS/search)•> N*(AMS/search/play) buttons(pages 7, 8, 12)

*The button has a tactile dot to help you operate the CD player by touch. 5

Remote control

NoteUse only the supplied remote control. You cannotoperate this CD player with the remote controlsupplied with other CD players.

qgx (stop) button(pages 8, 16)

qk PLAY MODEbutton(pages 10 - 12, 16)

qdDisplay(pages 9, 11 - 15)

qjDISPLAYbutton(pages 13, 14)

wd SOUND button(page 14)

qf Rotary controlN/>: play, AMS/search (pages 8, 12).: AMS/search (pages 8, 12)VOL +/–: Pull the control in the direction of thearrow, and then turn it toward + or –. (page 8)

ql RPT (repeat)/ENT(enter) button(pages 10 - 12)

w;HOLD switch(page 15)

qh Clip

Getting started

wai (headphones) jack(page 7)

wsX (pause) button(page 8)

6

Using the carrying pouchYou can carry your player and its battery case together using the supplied carrying pouch. Insertthem into the proper places in the pouch as illustrated below.

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

7

SECTION 3DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

3-2. UPPER LID (A) SUB ASSY

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

3-2. UPPER LID (A) SUB ASSY()

3-3. CABINET (UPPER) SUB ASSY(Page 8)

3-4. MAIN BOARD,OPTICAL PICK-UP SECTION (CDM-3325ES)(Page 8)

SET

3 guide (L)

2 screw (M1.4)

4 screw (M1.4)

1 Open the upper lid (A) sub assy.

6 Remove the upper lid (A) sub assy in the direction of arrow A.

A

5 guide (R)

!

@

Ver 1.1

Note: To install screws, tighten them with 0.4kg/cm2 of torque.(If tighten them too hard, portion ! may get cracked.)

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

8

4 cabinet (lower) assy

6 main board

1 cushion

5 flexible board (CN503)

7 two insulators

7 insulator

8 optical pick-up section(CDM-3325ES)

1 cushion

2 two connectors(CN501, CN502)

3 Hold up both the main board and the optical pick-up section at once, and remove them form the cabinet (lower) assy.

Note : Handle the flexible board with care whenyou hold up the optical pick-up section.

3-3. CABINET (UPPER) SUB ASSY

3-4. MAIN BOARD, OPTICAL PICK-UP SECTION (CDM-3325ES)

6 spring (upper lid-2702)

5 battery terminal board (relay)

3 claw

2 three screws (B2)2 four screws (B2)

1 screw (B2)

4 cabinet (upper) sub assy

Note : On installation of cabinet (upper) sub assy,adjust the position of two switches (S802, S803)and two knobs (GPRO).

knob (GPRO)

S802

3 claw

3 claw

S803

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

99

SECTION 4ELECTRICAL CHECK

The CD section adjustments are done automatically in this set.In case of operation check, confirm that focus bias.

Precautions for Check1. Perform check in the order given.2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise

indicated.3. Power supply voltage requirement: DC4.5 V in DC IN jack.

(J401)VOLUME : MinimumAVLS switch : NORMHOLD switch : OFFG•PROTECTION switch : 1

Connecting and Checking Location:

– MAIN Board (Component Side) –

Focus bias CheckCondition:• Hold the set in horizontal state.

Connection:

Procedure:1. Connect the oscilloscope to the test points TP601 (RF) and

TP418 (GND) on the MAIN board.2. Set a disc. (YEDS-18)3. Press the > N button.4. Check the oscilloscope waveform is as shown below.

A good eye pattern means that the diamond shape (◊) in thecenter of the waveform can be clearly distinguished.

RF Signal reference Waveform (Eye Pattern)

VOLT/DIV : 100 mV (With the 10:1 probe in use) TIME/DIV : 500 ns

To watch the eye pattern, set the oscilloscope to AC range andincrease the vertical sensitivity of the oscilloscope for easy watch-ing.

5. Stop revolving of the disc motor by pressing the x button.

oscilloscope (AC range)

+–

MAIN board

TP601 (RF)TP418 (GND)

2 k Ω

RF level0.4 to 0.6 Vp-pC4

04

D403 KA

R305

R489

VDR3

04

VDR3

03

R410

C301

CN50

3

C449

+R604

R601R603

C601C603

R602

C606

C605

C448

C604

55

C454C453

R469

C452

FB10

1

VDR1

01

VDR201

FB301

FB201

R303R304

C102

C202R1

02

R202R101R201

1

12

24

13

IC404

VDR3

01

J301LINE OUT(OPTICAL)

1

15

OPTICALPICK-UPBLOCK

DAX-25E

TP601 (RF)

TP418(GND)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1010

RF AMP,DIGITAL SIGNAL PROCESSOR,DIGITAL SERVO PROCESSOR,

D-RAM CONTROLLERIC601

DIGITALOUT

LPF

SIGNALPROCESSOR

BLOCK

MEMORYCONTROLLER,

BUS BOOSTBLOCK

SERVOBLOCK

MDS

MDP

SENS

SCORSDTO

XTAI

XTAO

RFAC

XSOE

R4MXLATCLOK

DOUT

XRASXWE

XCAS

AOUT1AOUTL,AOUTR

HPL,HPR

AOUT2

LRMU

FOK

XRST

RFDC

BA

SFDRSRDRFFDRFRDRTFDRTRDR

D0-D3

A0-A10

WDCKWFCK

XTAOXTAI

EF

89F

92

91

A

B

88

81

RFDC

RFAC

E

LASER DIODE

OPTICAL PICK-UP BLOCK DAX-25E

AA

B

RF

E

F

B

RF

E

F

PD

PD

LD

LD

DETECTOR

VCC

X60116.9344MHz

A

B

90

2, 3

, 24,

25

9 –

12, 1

5 –

19, 2

1, 8

5423

D-RAMIC602

D1 –

D4

A0 –

A10

DOUT

XRASXWEXCAS

D

E

G

H

10099

SFDRSRDR

9695

FFDRFRDR

9897

1718

4041

2122

3432

3836

2624

TFDRTRDR

M901(SLED)

(FOCUS)

(TRACKING)

FI2RI2

FI1RI1

FI4FI4

FO2RO2

FO1RO1

FO4RO4

FOCUS/TRACKING COIL DRIVERSLED MOTOR DRIVER

IC403 (1/2)

262422 32232021

91216 1415181711

PREDRIVER

102 MDS103 MDP

27

SCOR

104

23

241

18

19

20

11

13

15

21

74

72

17

C176

FOK

R4M

40

HOLD

28

CLOS

E

XSOE

WDC

K

SDTD

SENS

CLOK

XLAT

XSOEXIN

GRSC

OR FOK

MSD

TO

SCOR

MSD

TIM

SCK

XLAT

+BUFFERIC405

SYNC

897

XRST

DATA

XLTCHCLK

PWM

23APWMXBRAK

FG+

+

U1

V1

W1

COM

U

V

W

VGVG

SPINDLE MOTOR DRIVERIC404

M902(SPINDLE)

FG/FGSEL

XDRVLT

C HOLD

OFF

VCPU B+

SL806(OPEN)

VCPU B+

SYSTEM CONTROLLERIC801 (1/3)

SDTO

SCK

J

L

K

SYNC

2-AXISDEVICE

CPUINTERFACE

S801HOLD

61

28

62

4, 3

, 6, 5

116

– 11

3, 1

7 –

15, 1

3 –

11, 1

17

51

56

48

47

129

LRMU

XRST

HPL

HPR F43

44

• SIGNAL PATH

: CD PLAY (ANALOG OUT)

: CD PLAY (OPTICAL OUT)

V

U W

6

CONTROLLER,H BRIDGE DRIVER

2

M

CONTROLCIRCUIT

65

13

SYSM

AMUT

E

25

S804OPEN

VCPU B+

OPSTB

OPGSW

78

77 HG XSTB

HG GUP

(Page 12)

(Page 12)

(Page 12)

(Page 11)

(Page 11)

(Page 11)

(Page 11)

(Page11)

(Page 12)

(Page 12)

(Page 12)

SECTION 5DIAGRAMS

5-1. BLOCK DIAGRAM – MAIN Section (1/2) –

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1111

5-2. BLOCK DIAGRAM – MAIN Section (2/2) –

G

6 24 79 30 2625

B+ SWITCHQ301

LINE MUTINGCONTROL SWITCH

Q302

P21

AD S

EL

XRST

BEEP

AD R

MKE

Y

AD K

EY

SYSTEM CONTROLLERIC801(2/3)

VCC3

(LINE OUT JACK)

J301

LINE OUT(OPTICAL)

OPTICALTRANSCEIVER

31

TSB

VCPU 2V

TSB

RMKEY

GND

J302

i

S805-809

4

3

2

1

VCPU B+

IN_L

IN_R

HEADPHONE AMPIC301

13

12

OUT_L

OUT_R

BEEPO_L

BEEPO_R

4

9

PW_SW

MUTE_SW17

BEEP15

PW SW

BEEP

MUTE SW

18

SL807(TEST)

HPL

HPR

D

F

H

E

DOUT

AOUTLAOUTR

LRMU

XRST

MUTINGQ303

• SIGNAL PATH

: CD PLAY (ANALOG OUT)

: CD PLAY (OPTICAL OUT)

3

10

39

AVLS

LIMIT

NORM

VCPU B+S802AVLS

38ES

P

2

1

VCPU B+S803

G•PROTECTION

(Page 10)

(Page 10)

(Page 10)

(Page 10)

(Page 10)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1212

LINEARCONSTANT CURRENT,CONSTANT VOLTAGECHARGING BATTERY

CHARGE CIRCUIT

CHARGING BATTERYVOLTAGE DETECTOR

CIRCUIT

PRE-DRIVER

SWITCHINGPOWERCIRCUIT

CHARGE ONSWITCH

Q403

SWITCHINGPOWERCIRCUIT

LINEARREGULATOR

INTERFACE

VGPOWERCIRCUIT

CLKOR OSC

45

46

43

65

42

CHGSWRF1INM1

RF41

RF41

RF4

RF4

VCC1

VCPU

VLGO3

VCC2

VCC1

INM4

INM4

APCREF

APCREF

DTC3VREF

PAPC

PAPC

WAKELATCHDATACLOCK

DATA

CLOCK

VLGO4

SYNC

14

13

6

5

3

12

16

51

15

56

61

50

STNG57

7

791

73

58

11

SDTO

SCK

PD

LD

J

L

K

B

ASYNC

DTC2

DTC3INP2

INP2

RS1

DC IN

VIN

VCC3VCPU

RF1

INM1

RS1

CHGSW

VIN

DCIN

VCC375

VCC274

DTC253

LATCH

WAKE

VLGO2

BATM1

CHGMNT

BATM2

CHGMNT

VLGO4

VLGO2

VLG3

VGL5

9

8

VG

L5

BATM1

RSTB

75XPOWLT

21AD CHGMNT

27AD DCINMNT

33EXTBATT

22AD BATMNT

80LEDDISP

29PPG

70AGCPWN

SYSTEM CONTROLLERIC801 (3/3)

VCC1

VCC3

49 VDRAM10NC

VCPU B+

VCC2

D801CHARGE

66XWAKE

8RESET

37XSTAND ON

7BATVCC ON

76CHGGND ON

D405

D403

D404

RECHARGEABLEBATTERYNC-6WM

2PCS. 2.4V

– +

J401EXT BATTDC IN 4.5V

VG

CHARGE

CPOWER CONTROL

IC403 (2/2)

VREF

SAWGEN.

60BATM2 59

B+ SWITCHIC402

B+ SWITCHQ416, 417

CHARGECONTROLQ406, 415

RIPPLEFILTERQ408

B+ SWITCHQ421, 422

48

+

–CHARGE

TERMINAL

CHARGE ONSWITCH

Q412

EXTERNAL BATTERYDETECT

Q407CHARGE STAND

DETECTQ407

2

SWITCHINGQ419

RF378

SWITCHINGQ420

B+ SWITCHQ418

69

VIN B+

(Page 10)

(Page 10)

(Page 10)

(Page 10)

(Page 10)

(Page 10)

5-3. BLOCK DIAGRAM – POWER SUPPLY Section –

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1313

2.0 Vp-p

950 ns

400 to 600 mVp-p

2.4 Vp-p

59.1 ns

2.5 Vp-p

236 ns

2 IC601 w; (CLOK)

2.0 Vp-p

950 ns

2.0 Vp-p

950 ns

Note on Printed Wiring Board• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• z : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

• MAIN board is multi-layer printed board. However, the patternsof intermediate-layer have not been included in the diagram.

Caution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.

Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• % : indicates tolerance.• C : panel designation.

• A : B+ Line.• Power voltage is dc 4.5 V and fed with regulated dc power

supply from DC IN jack (J401).• Voltages and waveforms are dc with respect to ground in

no-signal conditions.no mark : CD PLAY

• Voltages are taken with a VOM (Input impedance 10 MΩ).Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

J : CD PLAY (ANALOG OUT)c : CD PLAY (OPTICAL OUT)

5-4. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

3 IC601 es (R4M)

4 IC601 rk (XTAO)

5 IC601 if (RFAC) (CD play mode)

6 IC601 ik (RFDC) (CD play mode)

7 IC403 qd (CLOK)

8 IC801 2 (XIN)

2.5 Vp-p

236 ns

400 to 600 mVp-p

• Waveforms

1 IC404 9 (CLK)

9 IC801 qk (MSCK)

2.0 Vp-p

950 ns

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1414

C404

D403 KA

R305

R489

VDR3

04

VDR3

03

R410

C301

CN50

3

C449

+R604

R601R603

C601C603

R602

R606R614

C611R6

07

C612

R615

R608C613

C602 R619 R605

C606

C605

C448

R618

R613

R612

C604

R610

R611

C609

C455

C454C453

R469

C452

FB10

1

VDR1

01

VDR201

FB301

FB201

R303R304

C102

C202R1

02

R202R101R201

1

12

24

13

IC404

1

120

30

31

60

6190

91

IC601

R609

C614

R622

C626

R632 R6

31

R630

R629

R628 R6

27

C304

C305 C303

+

C302

VDR803

R803

R203

R492

R204

C204

C205

R205

C207

C206

R208

1 12

24 13

IC301

R806

C803

IC801

120

21

40

6041

80

61

R307R820

R310C311

D306

AK

D305

KA

KA

D304

AKD307

FB303

FB30

4

C313

R309 R308

VDR1

02

FB403KA

D303

R207

R107

VDR2

02

R401

R428

C403

R482

R409

IC4021 4

8 5

R415

C406

E

C

BQ406

R414

C468

R465R463

2B 1BER460

R461 C469

C443

KAD405

R481

R480

C445

C465

R454

C439

C434

C431R450

R455

R447

C438

C437

R449

C436

C442

R448

R425

AK

D404R459

R446

R424

R457 R456R452C435

C429

R426

Q407BCER4

29

VDR401

C409R420

R441

R423

R422

C423R445C421R442

R443

1

20

2140

41

60

61 80C4

16R432

R440C

Q417

SD

G

Q415

C414

R483

BE

6

4

1

3

Q416

R484

E

C

BQ403

1E 1B 2C

1C 2B 2E

R419

Q419 2E 2B 1C

2C 1B 1E

R490

R491 R485

Q418Q420

R487

VDR3

01

R486

R436C418

IC403

Q421

4 6

3 1

R488

2C 1CQ422

D401

AK

C4052E 2B 1C

2C 1B 1E

R416

R413

C412

C424+

C413

+

R437

C419

R435

R474

R813

R808

C811C8

10

C804

R458

C807C805 C809

R812R811

C808

R805

R804

R801

R802

C801

C802

C623

R626

R634

C622

R105

R206R106

R108

R103

C104C106 C105

R104

R625C625

C619

C814R815

R816R817

R814

R818

C618

C812R821

R620C615

R623

C608

R621

C457R471

R470

C456

R468

R467

C447

R301

R302

C501

R478R4

79

R477

C433

+

C466

+

C432

+

R439

C425

C426

+

L405

L403

L411

L410

C444

+

L401 L408

L404

L402

L406

L409

C446

+

C422

+

FB404

FB40

5

R807

VDR804FB80

3

D803

K

A AD804

D408A K

SL806(OPEN)

C440

+

C401

+

C462

C464

FB20

2

FB10

2

FB302

C312

S806

S807

S805

S809

S808

D801

R819

X601

C208

+

C108

+

C310C3

09

C306

L303

S802

S803

R418

C408

R417

C806+FB801

VDR801

VDR6

01

L604

C624

+

IC602

1

13

R635

26

14

FB60

2

C620

L602

FB60

1

C621 +

L413

C607+

D601

C617 +

C107

D406

AK

C450

L503L501

L502

C616

+

AKD407

C451

Q302

1E1B2C1C2B2E

Q303

C502

+

Q414

BC

E

BCE

Q301

FB40

2

C610

C411

+

S804

Q405

J302

R444

R421

IC405

13

4 5

CN501

CN502

VDR4

03

31

46

FB401

Q412

i

1-682-611- 11(11)

M901(SLED)

M

RED

BLK

2

1

41

M902(SPINDLE)

V

W

UBLKORGWHTRED

4

1

MAIN BOARD(COMPONENT SIDE)A

B

C

D

E

F

G

H

1 2 3 4 5 6 7 8 9 10 11 12 13 14

1-682-611-

11(11)

MAIN BOARD(CONDUCTOR SIDE)

J401EXT BATTDC IN 4.5V– +

1 2

2C1B1E

2E2B1C

CHARGE

VOL –

VOL +

x/CHARGE

.

> N

SL808

SL809

SL810

D805

SL807(TEST)

S802AVLSLIMIT

NORM

S803G • PROTECTION

2

1

E B

C

OPEN

D601,D804, 805


2PSC. 2.4V

– +CHARGE TEMINAL

S801HOLDHOLD

OFF


1

15

OPTICALPICK-UPBLOCK

DAX-25E

I

J

TP418(GND)

TP601(RF)

C417

C307

+

5-5. PRINTED WIRING BOARD

D303 H-13D304 H-13D305 H-13D306 H-13D307 H-13D401 J-9D403 B-12D404 I-11D405 I-11D406 C-3D407 D-2D408 H-3D601 E-2D801 E-1D803 G-4D804 G-3D805 G-4

IC301 F-13IC402 I-12IC403 H-10IC404 D-13

• Semiconductor Location

IC405 D-2IC601 E-12IC602 E-4IC801 G-12

Q301 C-3Q302 C-2Q303 C-2Q403 H-9Q405 H-3Q406 H-12Q407 J-10Q412 B-3Q414 C-3Q415 H-9Q416 I-9Q417 H-9Q418 H-10Q419 G-9Q420 G-10Q421 I-12Q422 I-12

Ref. No. LocationRef. No. Location

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1515

5-6. SCHEMATIC DIAGRAM – MAIN Board (1/3) – • See page 13 for Waveforms. • See page 18 for IC Block Diagrams.

The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.

(Page 16) (Page 17)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1616

5-7. SCHEMATIC DIAGRAM – MAIN Board (2/3) – • See page 13 for Waveform.

(Page 15)

(Page 17)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1717

IC801T5AJ4-3HE0

5-8. SCHEMATIC DIAGRAM – MAIN Board (3/3) – • See page 13 for Waveforms.

(Page 15)

(Page 16)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

1818

• IC Block Diagrams

IC301 TA2152FN (EL)

+ –

24

OUT

ADJ

23

BIAS

IN

22

RF IN

21C-

AMP

SW20

GND

19

BIAS

OUT

18

BEEP

IN

17

MUT

E SW

16

PW S

W

15

MUT

E TC

14

VCC1

13

INB

1

NC

2

NC

3

BEEP

OUT

B

4

OUTB

5

EQB

6

OUTC

7

PW G

ND

8

EQA

9

OUTA

10BE

EP O

UTA

11

VCC2

12

INA

+–

BIAS

C-AMP SW BEEP PW/MUTE SW

PWA PWC PWB

IC404 TB2127AFN (EL)

+–

CONTROL

+–

+–

+–

TRIANGULARWAVE

GENERATING

INTE

RFAC

E

PRE-DRIVER

VC1SYNC

2XBRK

3FG

4VC

5DGND

6XRST

7DATA

8XLAT

9CLK

10VDU

11U

12PGUV

24 PWM

23 APWM

22 AGND

21 VG

20 COM

19 UI

18 VI

17 WI

16 PGW

15 W

14 VDVW

13 V

• IC403 TB2130F (FOCUS/TRACKING COIL DRIVER, SLED MOTOR DRIVER, POWER CONTROL)

Pin No. Pin Name I/O Description

1 VREF I Reference voltage input terminal

2 RF41 O Power supply 4 (APC) section operational amplifier 1 output

3 PAPC I Power supply 4 (APC) section operational amplifier 1 non-invert input

4 VINDET I VIN detection signal input terminal Not used (open)

5 RF4 O Power supply 4 (APC) section operational amplifier 2 output

6 INM4 I Power supply 4 (APC) section operational amplifier 2 invert input

7 APCREF I AGC control pulse signal input from the system controller (IC801)

8 L5 — Connected to the inductor for VG

9 VG O VG output terminal

10 GND — Ground terminal

11 SYNC I 176.4 kHz clock signal input from the CXD3029R (IC601)

12 WAKE I Wakeup control signal input from the system controller (IC801) (for system standby reset)“L”: wakeup The stop status is reset with the falling edge of input signal

13 CLOK I Serial data transfer clock signal input from the system controller (IC801)

14 DATA I Serial data input from the system controller (IC801)

15 LATCH I Serial data latch pulse signal input from the system controller (IC801)

16 RSTB O System reset signal output to the system controller (IC801) “L”: resetFor several hundreds msec. after the power supply rises, “L” is output, then it changes to “H”

17 FI2 I Sled servo drive signal (+) input from the CXD3029R (IC601)

18 RI2 I Sled servo drive signal (–) input from the CXD3029R (IC601)

19 FI3 I Not used (fixed at “L”)

20 RI3 I Not used (fixed at “L”)

21 FI4 I Tracking servo drive signal (+) input from the CXD3029R (IC601)

22 RI4 I Tracking servo drive signal (–) input from the CXD3029R (IC601)

23 VD4 I Power supply input terminal for tracking servo drive

24 RO4 O Tracking coil drive signal (–) output

25 MGND4 — Ground terminal (for tracking servo drive)

26 FO4 O Tracking coil drive signal (+) output

27 VD34 I Power supply input terminal for tracking servo drive

28 RO3 O Not used (open)

29 MGND3 — Ground terminal

30 FO3 O Not used (open)

31 VD23 I Power supply input terminal for sled servo drive

32 RO2 O Sled motor (M901) drive signal (–) output

33 MGND2 — Ground terminal (for sled servo drive)

34 FO2 O Sled motor (M901) drive signal (+) output

35 VD12 I Power supply input terminal for focus servo drive and sled servo drive

36 RO1 O Focus coil drive signal (–) output

37 MGND1 — Ground terminal (for focus servo drive)

38 FO1 O Focus coil drive signal (+) output

39 VD1 I Power supply input terminal for focus servo drive

40 FI2 I Focus servo drive signal (+) input from the CXD3029R (IC601)

41 RI2 I Focus servo drive signal (–) input from the CXD3029R (IC601)

42 CHGSW O Battery charge control transistor drive signal output

43 RS1 I Battery charge current detection terminal

44 INP1 I Battery charge circuit error amplifier non-invert input terminal for rechargeable batteryNot used (open)

5-9. IC PIN FUNCTION DESCRIPTION

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






19

D-EJ955


45 INW1 I Battery charge circuit error amplifier invert input for rechargeable battery

46 RF1 O Battery charge circuit error amplifier output for rechargeable battery

47 VOUT1 O VIN power supply circuit control transistor drive signal output terminal Not used (open)

48 DCIN I DCIN (AC adapter power supply) detection terminal

49 VDRAM O VDRAM output to the system controller (IC801)

50 VCPU I VCPU input terminal

51 VCC1 O VCC1 output terminal

52 DFLAY — Constant terminal at the VCC1 control

53 DTC2 — Power supply 2 (VCPU) duty setting terminal

54 INM2 I Power supply 2 (VCPU) operational amplifier invert input

55 RF2 O Power supply 2 (VCPU) operational amplifier output

56 INP2 I Power supply 2 (VCPU) operational amplifier non-invert input

57 STNG — Connected to the external transistor for power supply 2 (VCPU)

58 CHGMNT O Battery charge voltage detection signal output to the system controller (IC801)

59 BATM2 I Lower rechargeable battery minus terminal

60 BATM1 I Upper rechargeable battery minus terminal

61 VLGO2 O Power supply 2 (VCPU) output terminal

62 L2L — Connected to the inductor for power supply 2 (VCPU)

63 PGND2 — Ground terminal (for power supply 2 (VCPU))

64 L2H — Connected to the inductor for power supply 2 (VCPU)

65 VIN I VIN input terminal for power supply 4

66 L4L — Connected to the inductor for power supply 4 (VAPC)

67 PGND4 — Ground terminal (for power supply 4 (VAPC))

68 L4H — Connected to the inductor for power supply 4 (VAPC)

69 VLGO4 O Power supply 4 (VAPC) output terminal

70 L3L — Connected to the inductor for power supply 3 (VDAC)

71 PGND3 — Ground terminal (for power supply 3 (VDAC))

72 L3H — Connected to the inductor for power supply 3 (VDAC)

73 VLGO3 O Power supply 3 (VDAC) output terminal

74 VCC2 I VCC2 input terminal for VCC3

75 VCC3 O VCC3 (VDOJ) output terminal

76 INP3 I Power supply 3 (VDAC) operational amplifier 1 invert input

77 INM3 I Power supply 3 (VDAC) operational amplifier 1 non-invert input

78 RF3 O Power supply 3 (VDAC) operational amplifier output and connected to the external transistor for power supply 3 (VDAC)

79 DTC3 — Power supply 3 (VDAC) duty setting terminal

80 DTC4 — Power supply 4 (VAPC) duty setting terminal

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






20

D-EJ955

•


1 XRAS O Row address strobe signal output to the D-RAM (IC602)

2 XWE O Data input enable signal output to the D-RAM (IC602)

3 to 6 D1, D0, D3, D2 I/O Two-way data bus with the D-RAM (IC602)

7, 8 TEST1, TEST2 O Output terminal for the test Not used (open)

9 XCAS O Column address strobe signal output to the D-RAM (IC602)

10 WFCK O WFCK signal output terminal Not used (open)

11 to 13 A9 to A7 O Address signal output to the D-RAM (IC602)

14 DVSS — Ground terminal (for D-RAM interface)

15 to 17 A6 to A4 O Address signal output to the D-RAM (IC602)

18 XRDE I D-RAM read enable signal input terminal Not used (open)

19 VDD0 — Power supply terminal (digital system)

20 CLOK I Serial data transfer clock signal input from the system controller (IC801)

21 SDTO I Serial data input from the system controller (IC801)

22 SENS O Serial data output to the system controller (IC801)

23 XLAT I Serial data latch pulse signal input from the system controller (IC801)

24 XSOE I Serial data output enable signal input from the system controller (IC801)

25 SYSM I Analog muting on/off control signal input from the system controller (IC801)“H”: muting on

26 WDCK O GRSCOR signal output to the system controller (IC801)

27 SCOR O Subcode sync (S0+S1) detection signal output to the system controller (IC801)

28 XRST I Reset signal input from the system controller (IC801) “L”: reset

29 PWMI I Spindle motor external control signal input terminal Not used (open)

30 XQOK I Subcode Q OK signal input terminal Not used (open)

31 XWRE I D-RAM write enable signal input terminal Not used (open)

32 R4M O System clock output to the system controller (IC801)

33 VSS0 — Ground terminal (digital system)

34 SQCK I SQSO readout clock signal input terminal Not used (fixed at “H”)

35 SCLK I SENS serial data read clock signal input terminal Not used (fixed at “H”)

36 SQSO O CD text data output terminal Not used (open)

37 XEMP O D-RAM read prohibition signal output terminal Not used (open)

38 XWIH O D-RAM write prohibition signal output terminal Not used (open)

39 SBSO O Subcode P to W serial data output terminal Not used (open)

40 EXCK O SQSO readout clock signal output terminal Not used (pull down)

41 XSTL I Input terminal for the system clock frequency setting“L”: 16.9344 MHz, “H”: 33.8688MHz (fixed at “L” in this set)

42 HVSS — Ground terminal (for headphone)

43 HPL O PDM signal output for L-ch headphone to the headphone amplifier (IC301)

44 HPR O PDM signal output for R-ch headphone to the headphone amplifier (IC301)

45 HVDD — Power supply terminal (for headphone)

46 XVDD — Power supply terminal (for master clock)

47 XTAI I System clock input terminal (16.9344 MHz)

48 XTAO O System clock output terminal (16.9344 MHz)

49 XVSS — Ground terminal (for master clock)

50 AVDD1 — Power supply terminal (analog system)

51 AOUT1 O L-ch analog audio signal output

52 VREFL O L-ch reference voltage output terminal

53, 54 AVSS1, AVSS2 — Ground terminal (analog system)

C601 CXD3029R(RF AMP, DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, D-RAM CONTROLLER)

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






21

D-EJ995


55 VREFR O R-ch reference voltage output terminal

56 AOUT2 O R-ch analog audio signal output


58 TES1 I Input terminal for the test (normally: fixed at “L”)

59 TEST I Input terminal for the test (normally: fixed at “L”)


61 LRMU O Muting on/off control signal output to the audio line and the headphone amplifier (IC301)“H”: muting on

62 DOUT O Digital audio signal output

63 ATSK I/O Input/output terminal for anti-shock Not used (open)

64 DFCT I/O Defect signal input/output terminal Not used (open)

65 FOK O Focus OK signal output to the system controller (IC801) “L”: NG, “H”: OK

66 MIRR I/O Defect signal input/output terminal Not used (open)

67 COUT I/O Numbers of track counted signal input/output terminal Not used (open)

68 C2PO O C2PO signal output terminal Not used (open)

69 GFS O GFS signal output terminal Not used (open)

70 XUGF O XUGF signal output terminal Not used (open)

71 XPCK O XPCK signal output terminal Not used (open)


73 PCO O Charge pump output for master PLL

74 FILI I Filter input for master PLL

75 FILO O Filter output for master PLL

76 CLTV I VCO1 control voltage input terminal for multiplier

77 VCTL I VCO2 control voltage input terminal for broad-band EFM PLL

78 VPCO O Charge pump output terminal for broad-band EFM PLL

79 AVSS3 — Ground terminal (analog system)

80 ASYO O EFM full-swing output terminal

81 ASYI I Asymmetry comparator voltage input terminal

82 BIAS I Asymmetry circuit constant current input terminal


84 RFAC I EFM signal input from the optical pick-up


86 IGEN I Stabilized current input for operational amplifiers

87 AVSS0 — Ground terminal (analog system)

88 RFDC I RF signal input from the optical pick-up

89 E I E signal input from the optical pick-up

90 F I F signal input from the optical pick-up

91 B I B signal input from the optical pick-up

92 A I A signal input from the optical pick-up

93 VC I Middle point voltage input terminal Not used (fixed at “L”)


95 FRDR O Focus servo drive signal (–) output to the TB2130F (IC403)

96 FFDR O Focus servo drive signal (+) output to the TB2130F (IC403)

97 TRDR O Tracking servo drive signal (–) output to the TB2130F (IC403)

98 TFDR O Tracking servo drive signal (+) output to the TB2130F (IC403)

99 SRDR O Sled servo drive signal (–) output to the TB2130F (IC403)

100 SFDR O Sled servo drive signal (+) output to the TB2130F (IC403)

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






22

D-EJ995


101 SSTP I Disc inner position detection signal input terminal Not used (fixed at “L”)

102 MDS O Spindle motor (M902) drive signal output to the spindle motor driver (IC404)

103 MDP O Spindle motor (M902) servo control signal output to the spindle motor driver (IC404)

104 C176 O 176.4 kHz clock signal output to the power control (IC403) and spindle motor driver (IC404)


106 LRCK O L/R sampling clock signal (44.1 kHz) output terminal

107 LRCKI I L/R sampling clock signal (44.1 kHz) input terminal

108 PCMD O Serial data output terminal

109 PCMDI I Serial data input terminal

110 BCLK O Bit clock signal (2.8224 MHz) output terminal

111 BCLKI I Bit clock signal (2.8224 MHz) input terminal

112 DVDD — Power supply terminal (for D-ARM interface)

113 to 117 A3 to A0, A10 O Address signal output to the D-RAM (IC602)

118 A11 O Address signal output terminal to the D-RAM Not used (open)

119, 120 TEST3, TEST4 O Output terminal for the test Not used (open)

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






23

D-EJ995

• IC801 T5AJ4-3HE0 (SYSTEM CONTROLLER)


1 VSS — Ground terminal (digital system)

2 XIN I System clock input from the CXD3029R (IC601)

3 XOUT O High frequency oscillator output terminal Not used (open)

4 TEST I Test terminal for IC Not used (open)

5 VCPU — Power supply terminal

6 P21 O Digital output LED control signal output “L”: ON

7 BATVCC ON O Power supply control signal output for battery charge “H”: ON

8 RESET I System reset signal input from the power control (IC403) “L”: resetFor several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

9 FOK I Focus OK signal input from the CXD3029R (IC601) “L”: NG, “H”: OK

10 NC I VDRAM input from the power control (IC403)

11 SCOR I Subcode sync (S0+S1) detection signal input from the CXD3029R (IC601)

12 GRSCOR I GRSCOR signal input from the CXD3029R (IC601)

13 AMUTE O Analog muting on/off control signal output to the CXD3029R (IC601) “H”: muting on

14 XSOE O Serial data output enable signal output to the CXD3029R (IC601)

15 XLAT O Serial data latch pulse signal output to the CXD3029R (IC601)

16 MSDTI I Serial data input from the CXD3029R (IC601)

17 MSDTO O Serial data output to the power control (IC403), spindle motor driver (IC404) and CXD3029R (IC601)

18 MSCK O Serial data transfer clock signal output to the power control (IC403), spindle motor driver (IC404) and CXD3029R (IC601)

19, 20 VCPU — Power supply terminal

21 AD CHGMNT I Battery charge voltage detection signal input from the power control (IC403)

22 AD BATMNT I Battery voltage detection signal input and rechargeable battery use/no use detection signal input

23 AD VCDKEY2 I Key input terminal Not used (fixed at “H”)

24 AD SEL I Plug-in detection signal input of LINE OUT (OPTICAL)

25 AD KEY I Key input terminal (A/D input) x/CHARGE, > N, ., VOL +/– (S805 to S809) keys input

26 AD RMKEY I Key input from the headphone with remote commander (A/D input)

27 AD DCINMNT I DC input voltage detection signal input (A/D input) and DC input jack use/no use detection signal input

28 CLOSE I CD lid open/close detection switch (S804) input terminal “L”: CD lid open, “H”: CD lid closeThe stop status is reset with the falling edge of input signal

29 PPG O VCC2 voltage control signal output “H”: ON

30 BEEP O Beep sound output to the headphone amplifier (IC301)

31 TSB I/O Communication two-way data bus with the headphone with remote commander

32 VCPU2 — Power supply terminal Not used (open)

33 EXTBATT I External battery detection signal input

34 TEXTSKIP I Not used (open)

35 DIG TU I Not used (open)

36 LOADING I Not used (open)

37 XSTAND ON I Charge stand detection signal input

38 ESP I G•PROTECTION switch (S803) input terminal“L”: G•PROTECTION 1, “H”: G•PROTECTION 2

39 AVLS I AVLS (Automatic Volume Limiter System) switch (S802) input terminal“L”: normal, “H”: limit

40 HOLD I HOLD switch (S801) input terminal “L”: hold off, “H”: hold onwww. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






24

D-EJ955


41 to 56 SEG15 to SEG0 O Segment drive signal output terminal for the liquid crystal display Not used (open)

57 to 60 COM3 to COM0 O Common drive signal output terminal for the liquid crystal display Not used (open)

61 to 63 V3 to V1 O Liquid crystal display drive bias control signal output terminal Not used

64, 65 C1, C0 O Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage Not used

66 XWAKE O Wakeup control signal output to the power control (IC403) (for system standby reset)“L”: wakeup The stop status is reset with the falling edge of input signal

67 PGMSO O Not used (open)

68 PGMSI I Not used (open)

69 PGMSCK O Not used (open)

70 AGCPWM O AGC control pulse signal output to the power control (IC403)

71 IR RMC I Not used (fixed at “L”)

72 FG/FGSEL O FG pulse signal input from the spindle motor driver (IC404)

73 PGMSEL O Not used (open)

74 XDRVLT O Serial data latch pulse signal output to the spindle motor driver (IC404)

75 XPOWLT O Serial data latch pulse signal output to the power control (IC403)

76 CHGGND ON O Ground control signal output at the battery charge

77 HG XCTB O Hologram control signal output to the optical pick-up “L”: stop

78 HG GUP O CD-RW gain control signal output to the optical pick-up “H”: gain up

79 XRST O Reset signal output to the headphone amplifier (IC301), spindle motor driver (IC404) and CXD3029R (IC601) “L”: reset

80 LEDDISP O CHARGE LED (D801) drive signal output “L”: LED on

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






25

D-EJ955SECTION 6

EXPLODED VIEWS

• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.

• The mechanical parts with no reference num-ber in the exploded views are not supplied.

• Accessories are given in the last of the elec-trical parts list.

NOTE:• -XX and -X mean standardized parts, so they

may have some difference from the originalone.

• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)

↑ ↑Parts Color Cabinet's Color

• AbbreviationAUS : Australian modelCH : Chinese model

E13 : 220 – 230 V AC area in E modelE33 : 100 – 240 V AC area in E model

EE : East European modelFR : French model

6-1. UPPER LID, CABINET (UPPER) SECTION

9

1

45

6

4

33

3

2

8

cabinet (lower) section

7

FR

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

1 X-3381-431-1 LID (A) SUB ASSY (S), UPPER (SILVER)1 X-3381-432-1 LID (A) SUB ASSY (L), UPPER (BLUE)1 X-3381-433-1 LID (A) SUB ASSY (B), UPPER (BLACK)2 4-908-792-01 SCREW (B2)3 4-908-792-61 SCREW (B2)

4 3-232-536-07 SCREW (M1.4) (EG)5 3-234-003-01 GUIDE (L)6 3-234-004-01 GUIDE (R)7 X-3380-951-1 LID ASSY, BATTERY CASE (SILVER) (JE)7 X-3380-952-1 LID ASSY, BATTERY CASE (SILVER) (AEP, UK,

FR, EE, E33, CH, AUS)

7 X-3380-953-1 LID ASSY, BATTERY CASE (SILVER)(E13, HK, KR)

7 X-3381-665-1 LID ASSY (B) (//M), CASE(BLACK)...(BLACK, BLUE) (JE)

7 X-3381-666-1 LID ASSY (B) (//M), CASE (BLACK)...(BLACK, BLUE)

(AEP, UK, FR, EE, E33, CH, AUS)7 X-3381-667-1 LID ASSY (B) (//M), CASE

(BLACK)...(BLACK, BLUE) (E13, HK, KR)8 X-3381-434-1 CABINET (UPPER) SUB ASSY (PS) (SILVER)8 X-3381-435-1 CABINET (UPPER) SUB ASSY (PB)

(BLACK)...(BLACK, BLUE)

9 3-239-501-01 BATTERY, SHEET (FR)

Ver 1.1

HK : Hong Kong modelJE : Tourist modelKR : Korean model

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






26

D-EJ955

56

52

59

59CDM-3325ES

59

60

61

51

55

EXCEPT FR

57

57

54

53

6-2. CABINET (LOWER) SECTION


51 X-3381-159-2 CABINET (LOWER) ASSY (PS)(SILVER) (EXCEPT KR)

51 X-3381-160-2 CABINET (LOWER) ASSY (PB)(BLACK)...(BLACK, BLUE) (EXCEPT KR)

51 X-3381-161-2 CABINET (LOWER) ASSY (PS-K)(SILVER) (KR)

51 X-3381-162-2 CABINET (LOWER) ASSY (PB-K)(BLACK)...(BLACK, BLUE) (KR)

52 3-233-989-01 TERMINAL BOARD (-), CHARGE

53 3-233-988-01 TERMINAL BOARD (+), CHARGE

* 54 A-3021-564-A MAIN BOARD, COMPLETE (EXCEPT FR)* 54 A-3021-687-A MAIN BOARD, COMPLETE (FR)

55 3-222-300-02 TERMINAL BOARD (+), BATTERY56 3-222-301-02 TERMINAL BOARD (-), BATTERY57 3-831-441-99 CUSHION (EXCEPT FR)

59 3-234-106-01 INSULATOR60 3-233-990-01 TERMINAL BOARD (RELAY), BATTERY61 3-235-465-01 SPRING (UPPER LID-2702)

Ver 1.1

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






27

D-EJ955

6-3. OPTICAL PICK-UP SECTION(CDM-3325ES)

101

103

106

105

107

101

104

102

M901

M902

not supplied



101 3-318-203-62 SCREW (B1.7X4), TAPPING0102 X-3380-950-1 OPTICAL PICK-UP (DAX-25E)

103 3-221-473-01 COVER, GEAR104 3-221-472-01 CHASSIS105 3-221-474-01 SPRING, SLED

106 A-3052-734-A FEED ASSY, SCREW107 3-221-268-01 GEAR (B)M901 A-3052-733-A MOTOR ASSY, SLEDM902 A-3052-735-A MOTOR ASSY, TURN TABLE (SPINDLE)

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






28

D-EJ955

MAINSECTION 7

ELECTRICAL PARTS LIST


* A-3021-564-A MAIN BOARD, COMPLETE*********************

3-222-300-02 TERMINAL BOARD (+) , BATTERY3-222-301-02 TERMINAL BOARD (–) , BATTERY

< CAPACITOR/RESISTOR >

C102 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3VC104 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC105 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC106 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC107 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V

C108 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC202 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3VC204 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC205 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC206 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V

C207 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC208 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC301 1-117-720-11 CERAMIC CHIP 4.7uF 10VC302 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC303 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V

C304 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC305 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC306 1-115-156-11 CERAMIC CHIP 1uF 10VC307 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3VC309 1-216-864-11 METAL CHIP 0 5% 1/16W

C310 1-216-864-11 METAL CHIP 0 5% 1/16WC311 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC312 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC313 1-164-936-11 CERAMIC CHIP 680PF 10% 50VC401 1-104-852-11 TANTALUM CHIP 22uF 20% 10V

C403 1-115-156-11 CERAMIC CHIP 1uF 10VC404 1-115-156-11 CERAMIC CHIP 1uF 10VC405 1-107-820-11 CERAMIC CHIP 0.1uF 16VC406 1-117-720-11 CERAMIC CHIP 4.7uF 10VC408 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C409 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC411 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC412 1-115-156-11 CERAMIC CHIP 1uF 10VC413 1-110-569-21 TANTALUM CHIP 47uF 20% 4VC414 1-164-858-11 CERAMIC CHIP 22PF 5% 50V

C416 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC417 1-107-820-11 CERAMIC CHIP 0.1uF 16V

NOTE:• Due to standardization, replacements in the

parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.

• -XX and -X mean standardized parts, so theymay have some difference from the originalone.

• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.

• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .

• CAPACITORSuF: µF

• COILSuH: µH

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

C418 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC419 1-107-820-11 CERAMIC CHIP 0.1uF 16VC421 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V

C422 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC423 1-107-820-11 CERAMIC CHIP 0.1uF 16VC424 1-110-569-21 TANTALUM CHIP 47uF 20% 4VC425 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC426 1-110-569-21 TANTALUM CHIP 47uF 20% 4V

C429 1-107-820-11 CERAMIC CHIP 0.1uF 16VC431 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC432 1-110-569-21 TANTALUM CHIP 47uF 20% 4VC433 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC434 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C435 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC436 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC437 1-127-772-81 CERAMIC CHIP 33000PF 10% 10VC438 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC439 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C440 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC442 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC443 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC444 1-104-913-11 TANTALUM CHIP 10uF 20% 16VC445 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C446 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC447 1-107-820-11 CERAMIC CHIP 0.1uF 16VC448 1-115-156-11 CERAMIC CHIP 1uF 10VC449 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC450 1-164-506-11 CERAMIC CHIP 4.7uF 16V

C451 1-115-156-11 CERAMIC CHIP 1uF 10VC452 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC453 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC454 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC455 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V

C456 1-107-820-11 CERAMIC CHIP 0.1uF 16VC457 1-164-870-11 CERAMIC CHIP 68PF 5% 50VC462 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC464 1-164-156-11 CERAMIC CHIP 0.1uF 25VC465 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C466 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC468 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC469 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC501 1-107-820-11 CERAMIC CHIP 0.1uF 16VC502 1-104-847-11 TANTALUM CHIP 22uF 20% 4V

• AbbreviationAUS : Australian modelCH : Chinese modelE13 : 220 – 230 V AC area in E model

E33 : 100 – 240 V AC area in E modelEE : East European medelFR : French model

HK : Hong Kong modelJE : Tourist modelKR : Korean model

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







29

D-EJ955

MAIN

C601 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC602 1-164-854-11 CERAMIC CHIP 15PF 5% 50VC603 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC604 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC605 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V

C606 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC607 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC608 1-107-820-11 CERAMIC CHIP 0.1uF 16VC609 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC610 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C611 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC612 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC613 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC614 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC615 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C616 1-128-964-11 TANTALUM CHIP 100uF 20% 6.3VC617 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC618 1-164-866-11 CERAMIC CHIP 47PF 5% 50VC619 1-164-866-11 CERAMIC CHIP 47PF 5% 50VC620 1-115-156-11 CERAMIC CHIP 1uF 10V

C621 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC622 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC623 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC624 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC625 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C626 1-107-820-11 CERAMIC CHIP 0.1uF 16VC801 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC802 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC803 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC804 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C805 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC806 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC807 1-107-820-11 CERAMIC CHIP 0.1uF 16VC808 1-107-820-11 CERAMIC CHIP 0.1uF 16VC809 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C810 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC811 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC812 1-107-820-11 CERAMIC CHIP 0.1uF 16VC814 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

< CONNECTOR >

* CN501 1-785-877-21 HOUSING, CONNECTOR 4PCN502 1-784-342-21 HOUSING, CONNECTOR 2PCN503 1-573-924-11 CONNECTOR, FFC/FPC (ZIF) 15P

< DIODE >

D303 8-719-422-37 DIODE MA8051D304 8-719-422-37 DIODE MA8051D305 8-719-422-37 DIODE MA8051D306 8-719-422-37 DIODE MA8051D307 8-719-422-37 DIODE MA8051

D401 8-719-081-83 DIODE CRG01 (TE85L)D403 8-719-081-83 DIODE CRG01 (TE85L)D404 8-719-081-83 DIODE CRG01 (TE85L)D405 8-719-071-87 DIODE MA785-(TX) , SOD406 8-719-404-50 DIODE MA111-TX

D407 8-719-072-70 DIODE MA2ZD14001S0D408 8-719-081-83 DIODE CRG01 (TE85L)

D601 8-719-083-04 DIODE RSB6.8STE61D801 8-719-074-30 LED CL-190UR-CD-T (CHARGE)D803 8-719-056-66 DIODE 1SS378-TE85L

D804 8-719-083-04 DIODE RSB6.8STE61D805 8-719-083-04 DIODE RSB6.8STE61

< FERRITE BEAD/RESISTOR >

FB101 1-414-760-21 FERRITE 0uHFB102 1-414-760-21 FERRITE 0uHFB201 1-414-760-21 FERRITE 0uHFB202 1-414-760-21 FERRITE 0uHFB301 1-414-760-21 FERRITE 0uH


FB403 1-216-864-11 METAL CHIP 0 5% 1/16WFB404 1-414-760-21 FERRITE 0uHFB405 1-414-760-21 FERRITE 0uHFB601 1-414-760-21 FERRITE 0uHFB602 1-414-760-21 FERRITE 0uH

FB801 1-414-760-21 FERRITE 0uHFB803 1-414-760-21 FERRITE 0uH

< IC >

IC301 6-700-702-01 IC TA2152FN (EL)IC402 8-759-694-91 IC SI-3048LSA-TLIC403 6-700-703-01 IC TB2130FIC404 6-701-860-01 IC TB2127AFN (EL)IC405 8-759-594-55 IC TC75S57F (TE85R)

IC601 8-752-410-68 IC CXD3029RIC602 6-700-994-01 IC MT4LC4M4B1TG-6IC801 6-800-479-01 IC T5AJ4-3HE0

< JACK >

J301 1-793-659-11 JACK, OPTICAL OUT (LINE OUT (OPTICAL))J302 1-815-088-61 JACK, HEADPHONE (i)J401 1-793-156-31 JACK, DC (EXT BATT, DC IN 4.5V)

< COIL >

L303 1-400-144-21 INDUCTOR 22uHL401 1-414-434-11 INDUCTOR 100uHL402 1-414-398-11 INDUCTOR 10uHL403 1-414-404-11 INDUCTOR 100uHL404 1-419-188-41 COIL, CHOKE 100uH

L405 1-414-404-11 INDUCTOR 100uHL406 1-400-145-21 INDUCTOR 47uHL408 1-414-434-11 INDUCTOR 100uHL409 1-400-145-21 INDUCTOR 47uHL410 1-414-402-11 INDUCTOR 47uH


L602 1-414-521-11 INDUCTOR 10uHwww. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







30

D-EJ955

MAIN

L604 1-414-521-11 INDUCTOR 10uH

< TRANSISTOR >

Q301 8-729-028-86 TRANSISTOR DTA143EUA-T106Q302 8-729-429-50 TRANSISTOR XP4312Q303 8-729-427-72 TRANSISTOR XP4501Q403 8-729-921-73 TRANSISTOR 2SD1781K-QRQ405 8-729-921-93 TRANSISTOR 2SB1182F5-QR

Q406 8-729-230-63 TRANSISTOR 2SC4116-YGQ407 8-729-029-14 TRANSISTOR DTC144EUA-T106Q412 8-729-056-20 TRANSISTOR TPC6001 (TE85R)Q414 8-729-026-53 TRANSISTOR 2SA1576A-T106-QRQ415 8-729-026-30 FET 2SJ346-TE85L

Q416 8-729-056-19 TRANSISTOR TPC6101 (TE85R)Q417 8-729-230-63 TRANSISTOR 2SC4116-YGQ418 6-550-075-01 TRANSISTOR UMZ8NTRQ419 6-550-063-01 TRANSISTOR UMF8NTRQ420 6-550-063-01 TRANSISTOR UMF8NTR

Q421 8-729-056-19 TRANSISTOR TPC6101 (TE85R)Q422 8-729-426-30 TRANSISTOR XP1213-TXE

< RESISTOR >

R101 1-218-977-11 RES-CHIP 100K 5% 1/16WR102 1-218-945-11 RES-CHIP 220 5% 1/16WR103 1-218-965-11 RES-CHIP 10K 5% 1/16WR104 1-218-953-11 RES-CHIP 1K 5% 1/16WR105 1-218-953-11 RES-CHIP 1K 5% 1/16W

R106 1-218-965-11 RES-CHIP 10K 5% 1/16WR107 1-218-947-11 RES-CHIP 330 5% 1/16WR108 1-218-990-11 SHORT 0R201 1-218-977-11 RES-CHIP 100K 5% 1/16WR202 1-218-945-11 RES-CHIP 220 5% 1/16W

R203 1-218-965-11 RES-CHIP 10K 5% 1/16WR204 1-218-953-11 RES-CHIP 1K 5% 1/16WR205 1-218-953-11 RES-CHIP 1K 5% 1/16WR206 1-218-965-11 RES-CHIP 10K 5% 1/16WR207 1-218-947-11 RES-CHIP 330 5% 1/16W

R208 1-218-990-11 SHORT 0R301 1-218-953-11 RES-CHIP 1K 5% 1/16WR302 1-218-953-11 RES-CHIP 1K 5% 1/16WR303 1-218-983-11 RES-CHIP 330K 5% 1/16WR304 1-218-983-11 RES-CHIP 330K 5% 1/16W

R305 1-218-990-11 SHORT 0R307 1-218-953-11 RES-CHIP 1K 5% 1/16WR308 1-218-941-81 RES-CHIP 100 5% 1/16WR309 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR310 1-218-937-11 RES-CHIP 47 5% 1/16W

R401 1-216-864-11 METAL CHIP 0 5% 1/16WR409 1-218-965-11 RES-CHIP 10K 5% 1/16WR410 1-218-977-11 RES-CHIP 100K 5% 1/16WR413 1-216-298-00 METAL CHIP 2.2 5% 1/10WR414 1-218-957-11 RES-CHIP 2.2K 5% 1/16W

R415 1-218-990-11 SHORT 0R416 1-216-298-00 METAL CHIP 2.2 5% 1/10WR417 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR418 1-218-973-11 RES-CHIP 47K 5% 1/16WR419 1-218-990-11 SHORT 0

R420 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR421 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR422 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR423 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR424 1-216-864-11 METAL CHIP 0 5% 1/16W

R425 1-216-864-11 METAL CHIP 0 5% 1/16WR426 1-216-864-11 METAL CHIP 0 5% 1/16WR428 1-216-864-11 METAL CHIP 0 5% 1/16WR429 1-218-977-11 RES-CHIP 100K 5% 1/16WR432 1-216-864-11 METAL CHIP 0 5% 1/16W

R435 1-218-975-11 RES-CHIP 68K 5% 1/16WR436 1-218-965-11 RES-CHIP 10K 5% 1/16WR437 1-218-977-11 RES-CHIP 100K 5% 1/16WR439 1-216-864-11 METAL CHIP 0 5% 1/16WR440 1-218-981-11 RES-CHIP 220K 5% 1/16W

R441 1-218-989-11 RES-CHIP 1M 5% 1/16WR442 1-218-990-11 SHORT 0R443 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR444 1-218-971-11 RES-CHIP 33K 5% 1/16WR445 1-208-943-11 METAL CHIP 220K 0.5% 1/16W

R446 1-216-864-11 METAL CHIP 0 5% 1/16WR447 1-216-864-11 METAL CHIP 0 5% 1/16WR448 1-218-989-11 RES-CHIP 1M 5% 1/16WR449 1-218-990-11 SHORT 0R450 1-218-967-11 RES-CHIP 15K 5% 1/16W

R452 1-218-989-11 METAL CHIP 1M 0.5% 1/16WR454 1-218-965-11 RES-CHIP 10K 5% 1/16WR455 1-218-971-11 RES-CHIP 33K 5% 1/16WR456 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR457 1-208-927-11 METAL CHIP 47K 0.5% 1/16W

R458 1-218-969-11 RES-CHIP 22K 5% 1/16WR459 1-216-864-11 METAL CHIP 0 5% 1/16WR460 1-220-804-11 RES-CHIP 2.2M 5% 1/16WR461 1-218-965-11 RES-CHIP 10K 5% 1/16WR463 1-216-864-11 METAL CHIP 0 5% 1/16W

R465 1-216-864-11 METAL CHIP 0 5% 1/16WR467 1-208-947-11 METAL CHIP 330K 0.5% 1/16WR468 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR469 1-218-973-11 RES-CHIP 47K 5% 1/16WR470 1-208-707-11 METAL CHIP 10K 0.5% 1/16W

R471 1-208-719-11 METAL CHIP 33K 0.5% 1/16WR474 1-218-985-11 RES-CHIP 470K 5% 1/16WR477 1-218-985-11 RES-CHIP 470K 5% 1/16WR478 1-218-989-11 RES-CHIP 1M 5% 1/16WR479 1-218-981-11 RES-CHIP 220K 5% 1/16W

R480 1-216-864-11 METAL CHIP 0 5% 1/16WR481 1-216-864-11 METAL CHIP 0 5% 1/16WR482 1-218-949-11 RES-CHIP 470 5% 1/16WR483 1-218-945-11 RES-CHIP 220 5% 1/16WR484 1-218-977-11 RES-CHIP 100K 5% 1/16W

R485 1-218-989-11 RES-CHIP 1M 5% 1/16WR486 1-218-989-11 RES-CHIP 1M 5% 1/16WR487 1-218-989-11 RES-CHIP 1M 5% 1/16WR488 1-218-977-11 RES-CHIP 100K 5% 1/16WR489 1-218-990-11 SHORT 0

R490 1-218-989-11 RES-CHIP 1M 5% 1/16W

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







31

D-EJ955


R491 1-218-965-11 RES-CHIP 10K 5% 1/16WR492 1-218-990-11 SHORT 0R601 1-218-969-11 RES-CHIP 22K 5% 1/16WR602 1-218-985-11 RES-CHIP 470K 5% 1/16W

R603 1-218-973-11 RES-CHIP 47K 5% 1/16WR604 1-218-989-11 RES-CHIP 1M 5% 1/16WR605 1-218-941-81 RES-CHIP 100 5% 1/16WR606 1-218-969-11 RES-CHIP 22K 5% 1/16WR607 1-218-969-11 RES-CHIP 22K 5% 1/16W

R608 1-218-969-11 RES-CHIP 22K 5% 1/16WR609 1-218-969-11 RES-CHIP 22K 5% 1/16WR610 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR611 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR612 1-218-965-11 RES-CHIP 10K 5% 1/16W

R613 1-218-983-11 RES-CHIP 330K 5% 1/16WR614 1-218-977-11 RES-CHIP 100K 5% 1/16WR615 1-218-977-11 RES-CHIP 100K 5% 1/16WR618 1-218-965-11 RES-CHIP 10K 5% 1/16WR619 1-218-971-11 RES-CHIP 33K 5% 1/16W

R620 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR621 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR622 1-218-990-11 SHORT 0R623 1-218-939-11 RES-CHIP 68 5% 1/16WR625 1-218-949-11 RES-CHIP 470 5% 1/16W

R626 1-218-965-11 RES-CHIP 10K 5% 1/16WR627 1-218-990-11 SHORT 0R628 1-218-990-11 SHORT 0R629 1-218-990-11 SHORT 0R630 1-218-990-11 SHORT 0

R631 1-218-990-11 SHORT 0R632 1-218-990-11 SHORT 0R634 1-218-990-11 SHORT 0R635 1-216-803-11 METAL CHIP 33 5% 1/16WR801 1-218-977-11 RES-CHIP 100K 5% 1/16W

R802 1-218-977-11 RES-CHIP 100K 5% 1/16WR803 1-218-941-81 RES-CHIP 100 5% 1/16WR804 1-218-965-11 RES-CHIP 10K 5% 1/16WR805 1-218-989-11 RES-CHIP 1M 5% 1/16WR806 1-218-965-11 RES-CHIP 10K 5% 1/16W

R807 1-216-864-11 METAL CHIP 0 5% 1/16WR808 1-218-990-11 SHORT 0R811 1-218-965-11 RES-CHIP 10K 5% 1/16WR812 1-218-990-11 SHORT 0R813 1-218-977-11 RES-CHIP 100K 5% 1/16W

R814 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR815 1-218-953-11 RES-CHIP 1K 5% 1/16WR816 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR817 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR818 1-218-973-11 RES-CHIP 47K 5% 1/16W

R819 1-218-973-11 RES-CHIP 47K 5% 1/16WR820 1-218-989-11 RES-CHIP 1M 5% 1/16WR821 1-208-715-11 METAL CHIP 22K 0.5% 1/16W

< SWITCH >

S801 1-762-078-11 SWITCH, SLIDE (HOLD)S802 1-762-078-11 SWITCH, SLIDE (AVLS)S803 1-762-078-11 SWITCH, SLIDE(G•PROTECTION)S804 1-762-805-41 SWITCH, PUSH (1KEY) (OPEN)

S805 1-771-248-11 SWITCH, TACTILE (x/CHARGE)

S806 1-771-248-11 SWITCH, TACTILE (> N)S807 1-771-248-11 SWITCH, TACTILE (.)S808 1-771-248-11 SWITCH, TACTILE (VOL +)S809 1-771-248-11 SWITCH, TACTILE (VOL –)

< VARISTOR >

VDR101 1-801-862-11 VARISTOR, CHIPVDR102 1-801-923-11 VARISTOR, CHIPVDR201 1-801-862-11 VARISTOR, CHIPVDR202 1-801-923-11 VARISTOR, CHIPVDR301 1-801-862-11 VARISTOR, CHIP


VDR801 1-801-862-11 VARISTOR, CHIPVDR803 1-801-862-11 VARISTOR, CHIPVDR804 1-801-862-11 VARISTOR, CHIP

< VIBRATOR >

X601 1-795-003-21 VIBRATOR, CRYSTAL (16.9344MHz)**************************************************************

MISCELLANEOUS**************

0102 X-3380-950-1 OPTICAL PICK-UP (DAX-25E)M901 A-3052-733-A MOTOR ASSY, SLEDM902 A-3052-735-A MOTOR ASSY, TURN TABLE (SPINDLE)

************************************************************

ACCESSORIES************

0 1-475-622-21 ADAPTOR, AC (AC-E455) (CH)1-476-395-12 REMOTE CONTROL UNIT (RM-MC11EL/SK)

0 1-476-845-11 ADAPTOR, AC (AC-ES455) (AEP, FR, EE, E13)0 1-476-846-11 ADAPTOR, AC (AC-ES455) (HK)0 1-476-848-11 ADAPTOR, AC (AC-ES455) (UK)

0 1-476-850-11 ADAPTOR, AC (AC-ES455) (AUS)0 1-477-140-11 ADAPTOR, AC (AC-ES455) (KR)0 1-477-141-11 ADAPTOR, AC (AC-ES455) (E33, JE)

1-528-299-41 BATTERY, NI-CD (NC-6WM) (FR, EE)1-528-543-11 BATTERY, NI-CD (NC-6WM)

(EXCEPT AEP, UK, FR, EE)

1-528-543-22 BATTERY, NI-CD (NC-6WM) (AEP, UK)1-543-798-11 FILTER, CLAMP (FERRITE CORE)

(AEP, UK, EE, E13, HK, KR, CH, JE)0 1-569-007-11 ADAPTOR, CONVERSION 2P (E33, JE)

1-756-008-23 EXTERNAL BATTERY CASE1-756-222-11 STAND, CHARGE (BCA-WM50)

3-008-521-01 CASE, CHARGE3-234-486-01 MANUAL, INSTRUCTION (JAPANESE,

ENGLISH, TRADITIONAL CHINESE, KOREAN)(JE)

3-234-486-11 MANUAL, INSTRUCTION (SPANISH)(AEP, E33, JE)

3-234-486-21 MANUAL, INSTRUCTION (ENGLISH)(AEP, UK, EE, E33, AUS, JE)

MAIN

Ver 1.1

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







32

D-EJ955

3-234-486-31 MANUAL, INSTRUCTION (FRENCH)(AEP, FR, JE)

3-234-486-41 MANUAL, INSTRUCTION (DUTCH) (AEP, EE)3-234-486-51 MANUAL, INSTRUCTION (SWEDISH) (AEP)3-234-486-61 MANUAL, INSTRUCTION (PORTUGUESE)

(AEP)3-234-486-71 MANUAL, INSTRUCTION (GERMAN) (AEP)3-234-486-81 MANUAL, INSTRUCTION (ITALIAN) (AEP)

3-234-486-91 MANUAL, INSTRUCTION (FINNISH) (AEP)3-234-487-11 MANUAL, INSTRUCTION

(TRADITIONAL CHINESE) (E13, HK)3-234-487-21 MANUAL, INSTRUCTION (ENGLISH)

(E13, HK, CH)3-234-487-31 MANUAL, INSTRUCTION

(SIMPLIFIED CHINESE) (CH)3-234-488-11 MANUAL, INSTRUCTION (KOREAN) (KR)

3-234-488-21 MANUAL, INSTRUCTION (RUSSIAN) (EE)3-234-488-31 MANUAL, INSTRUCTION (CZECH) (EE)3-234-488-41 MANUAL, INSTRUCTION (HUNGARIAN) (EE)3-234-488-51 MANUAL, INSTRUCTION (POLISH) (EE)3-234-488-61 MANUAL, INSTRUCTION (SLOVAKIAN) (EE)

3-235-292-01 POUCH, CARRYING8-954-008-91 RECEIVER, EAR MDR-E808SP

Ver 1.1

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






SERVICE MANUAL

D-EJ955

SUPPLEMENT-1File this supplement with the service manual.

Subject: Change of MAIN board. (Suffix-12)

AEP ModelUK Model

E ModelAustralian Model

Chinese ModelTourist Model

Ver 1.1 2002.01

In this set, MAIN board has been changed in the midway of production.Printed wiring boards and schematic diagrams of new type, and changedparts list are described in this supplement-1.Refer to original service manual for other information.

• NEW/FORMER TYPE DISCRIMINATION

Former Type : 1-682-611-11New Type : 1-682-611-12

– MAIN BOARD (Component Side) –

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






2

D-EJ955

Note on Printed Wiring Board• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• z : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

• MAIN board is multi-layer printed board. However, the patternsof intermediate-layer have not been included in the diagram.

Caution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.

Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• % : indicates tolerance.• C : panel designation.

• A : B+ Line.• Power voltage is dc 4.5 V and fed with regulated dc power

supply from DC IN jack (J401).• Voltages and waveforms are dc with respect to ground in

no-signal conditions.no mark : CD PLAY

• Voltages are taken with a VOM (Input impedance 10 MΩ).Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

J : CD PLAY (ANALOG OUT)c : CD PLAY (OPTICAL OUT)

• AbbreviationFR : French model

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

• DIAGRAMSNOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

33

C404

D403 KA

R305

R489

R410

C301

CN50

3

C449

+R604

R601R603

C601C603

R602

R606R614

C611R6

07

C612

R615

R608C613

C602R619 R605

C606

C605

C448

R618

R613

R612

C604

R610

R611

C609

C455

C454C453

R469

C452

FB10

1

VDR1

01

VDR201

FB301

FB201

R303R304

C102

C202

R102 R202R101

R201

1

12

24

13

IC404

1

120

30

31

60

6190

91

IC601

R609

C614

R622

C626

R632 R6

31

R630

R629

R628 R6

27

C304

C305 C303

+

C302

VDR803

R803

R203

R492

R204

C204

C205

R205

C207

C206

R208

1 12

24 13

IC301

R806

C803

IC801

120

21

40

6041

80

61

R307R820

R310C311

D306

AK

D305

KA

KA

D304

AKD307

FB303

FB30

4

C313

R309 R308

VDR1

02

FB403KA

D303

R207

R107

VDR2

02

R401

R428

C403

R482

R409

IC4021 4

8 5

R415

C406

E

C

BQ406

R414

C468

R465R463

2B 1BER460

R461 C469

C443

KAD405 C4

45

C465

R454

C439

C434

C431R450

R455

R447

C438

C437

R449

C436

C442

R448

R425

AK

D404R459

R446

R424

R457 R456R452C435

C429

R426

Q407BCER4

29

VDR401

C409R420

C417

R441

R423

R422

C423R445C421R442

R443

1

20

2140

41

60

61 80

C416

R432

R440C

Q417

SD

G

Q415

C414

R483

BE

6

4

1

3

Q416

R484

E

C

BQ403

1E 1B 2C

1C 2B 2E

R419

Q419 2E 2B 1C

2C 1B 1E

R490

R491

R485Q418

Q420

R487

VDR3

01

R486

R436C418

IC403

Q421

4 6

3 1

R488

2C 1CQ422

D401

AK

C405

2E 2B 1C

2C 1B 1E

R416

R413

C412

C424+

C413

+R437

C419

R435

R474

R813

R808

C811C810

C804R458

C807C805 C809

R812R811

C808

R805

R804

R801

R802

C801

C802

C623

R626R634C622

R105

R206R106

R108

R103

C104C106 C105

R104

R625C625

C619

C814R815

R816

R817

R814

R818

C618

C812R821

R620C615

R623

C608

R621

C457R471

R470

C456

R468

R467

C447

R301

R302

C501

R478

R479

R477

C433+

C466

+

C432

+

R439

C425

C426

+

L405

L403

L411

L410

C444

+

L401 L408

L404

L402

L406

L409

C446

+

C422

+

FB404

FB405R807

FB80

3

D803KA A

D804

D408 A K

SL806(OPEN)

C440

+

C401

+

C464

L101

L201

FB302

C312

S806

S807

S805

S809

S808

D801

R819

X601

C208

+

C108

+

C310C3

09

C306

L303

S802

S803

R418

C408

R417

C806+FB801

VDR801

VDR6

01

L604

C624

+

IC602

1

13

R635

26

14

FB602

C620 L602

FB601

C621 +

L413

C607+

D601

C617 +

C107

D406

AK

C450

L503L501

L502

C616

+

AKD407

C451

Q302

1E1B2C1C2B2E

Q303

C502

+

Q414

BC

E

BCE

Q301

FB40

2

C610

C411

+

S804

Q405

J302

R444

R421

IC405

13

4 5

CN501

CN502VD

R403

31

46

FB401

Q412

i

1-682-611- 12(12)

M901(SLED)

M

RED

BLK

2

1

41

M902(SPINDLE)

V

W

UBLKORGWHTRED

4

1

MAIN BOARD(COMPONENT SIDE)A

B

C

D

E

F

G

H

1 2 3 4 5 6 7 8 9 10 11 12 13 14

1-682-611-

12(12)

MAIN BOARD(CONDUCTOR SIDE)

J401EXT BATTDC IN 4.5V– +

1 2

2C1B1E

2E2B1C

CHARGE

VOL –

VOL +

x/CHARGE

.

> N

D805

SL807(TEST)

S802AVLSLIMIT

NORM

S803G • PROTECTION

2

1

E B

C

OPEN

D601,D804, 805


2PSC. 2.4V

– +CHARGE TEMINAL

S801HOLDHOLD

OFF


1

15

OPTICALPICK-UPBLOCK

DAX-25E

I

J

TP418(GND)

TP601(RF)

C307

+

TH401

R493

R822(FR)

PRINTED WIRING BOARD

D303 H-13D304 H-13D305 H-13D306 H-13D307 H-13D401 J-9D403 B-12D404 I-11D405 I-11D406 C-3D407 D-2D408 H-3D601 E-2D801 E-1D803 G-4D804 G-3D805 G-4

IC301 F-13IC402 I-12IC403 H-10IC404 D-13

• Semiconductor Location

IC405 D-2IC601 E-12IC602 E-4IC801 G-12

Q301 C-3Q302 C-2Q303 C-2Q403 H-9Q405 H-3Q406 H-12Q407 J-10Q412 B-3Q414 C-3Q415 H-9Q416 I-9Q417 H-9Q418 H-10Q419 G-9Q420 G-10Q421 I-12Q422 I-12

Ref. No. LocationRef. No. Location

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

44

∗

∗

∗ R303, 304 220k (FR) 330k (EXCEPT FR)

SCHEMATIC DIAGRAM – MAIN Board (1/3) –


(Page 5) (Page 6)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

55


(Page 4)

(Page 6)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

66

(FR)

IC801T5AJ4-3HE0

∗

∗ R821 22k 0.5% (EXCEPT FR) 68k 0.5% (FR)

R822100k0.5%


(Page 4)

(Page 5)

w w w . x i a o y u 1 6 3 . c o m

Q Q 3 7 6 3 1 5 1 5 0 992894298

T E L 1 3 9 4 2 2 9 6 5 1 3 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






7

D-EJ955

MAIN


* A-3021-564-A MAIN BOARD, COMPLETE (EXCEPT French)* A-3021-687-A MAIN BOARD, COMPLETE (French)

*********************

3-222-300-02 TERMINAL BOARD (+) , BATTERY3-222-301-02 TERMINAL BOARD (–) , BATTERY

< CAPACITOR/RESISTOR >

C102 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3VC104 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC105 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC106 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC107 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V

C108 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC202 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3VC204 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC205 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC206 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V

C207 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC208 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC301 1-117-720-11 CERAMIC CHIP 4.7uF 10VC302 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC303 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V

C304 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC305 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC306 1-115-156-11 CERAMIC CHIP 1uF 10VC307 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3VC309 1-216-864-11 METAL CHIP 0 5% 1/16W

C310 1-216-864-11 METAL CHIP 0 5% 1/16WC311 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC312 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC313 1-164-936-11 CERAMIC CHIP 680PF 10% 50VC401 1-104-852-11 TANTALUM CHIP 22uF 20% 10V

C403 1-115-156-11 CERAMIC CHIP 1uF 10VC404 1-115-156-11 CERAMIC CHIP 1uF 10VC405 1-107-820-11 CERAMIC CHIP 0.1uF 16VC406 1-117-720-11 CERAMIC CHIP 4.7uF 10VC408 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C409 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC411 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC412 1-115-156-11 CERAMIC CHIP 1uF 10VC413 1-110-569-21 TANTALUM CHIP 47uF 20% 4VC414 1-164-858-11 CERAMIC CHIP 22PF 5% 50V

C416 1-164-935-11 CERAMIC CHIP 470PF 10% 50V

NOTE:• Due to standardization, replacements in the

parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.

• -XX and -X mean standardized parts, so theymay have some difference from the originalone.

• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.

• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .

• CAPACITORSuF: µF

• COILSuH: µH

When indicating parts by referencenumber, please include the board.

C417 1-107-820-11 CERAMIC CHIP 0.1uF 16VC418 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC419 1-107-820-11 CERAMIC CHIP 0.1uF 16VC421 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V

C422 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC423 1-107-820-11 CERAMIC CHIP 0.1uF 16VC424 1-110-569-21 TANTALUM CHIP 47uF 20% 4VC425 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC426 1-110-569-21 TANTALUM CHIP 47uF 20% 4V

C429 1-107-820-11 CERAMIC CHIP 0.1uF 16VC431 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC432 1-110-569-21 TANTALUM CHIP 47uF 20% 4VC433 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC434 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C435 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC436 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC437 1-127-772-81 CERAMIC CHIP 33000PF 10% 10VC438 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC439 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C440 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC442 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC443 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC444 1-104-913-11 TANTALUM CHIP 10uF 20% 16VC445 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C446 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC447 1-107-820-11 CERAMIC CHIP 0.1uF 16VC448 1-115-156-11 CERAMIC CHIP 1uF 10VC449 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC450 1-164-506-11 CERAMIC CHIP 4.7uF 16V

C451 1-115-156-11 CERAMIC CHIP 1uF 10VC452 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC453 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC454 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC455 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V

C456 1-107-820-11 CERAMIC CHIP 0.1uF 16VC457 1-164-870-11 CERAMIC CHIP 68PF 5% 50VC464 1-164-156-11 CERAMIC CHIP 0.1uF 25VC465 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC466 1-104-847-11 TANTALUM CHIP 22uF 20% 4V

C468 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC469 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC501 1-107-820-11 CERAMIC CHIP 0.1uF 16VC502 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC601 1-164-874-11 CERAMIC CHIP 100PF 5% 50V

• ELECTRICAL PARTS LIST

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







8

D-EJ955

MAIN

C602 1-164-854-11 CERAMIC CHIP 15PF 5% 50VC603 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC604 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC605 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC606 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V

C607 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC608 1-107-820-11 CERAMIC CHIP 0.1uF 16VC609 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC610 1-107-820-11 CERAMIC CHIP 0.1uF 16VC611 1-164-935-11 CERAMIC CHIP 470PF 10% 50V

C612 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC613 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC614 1-164-935-11 CERAMIC CHIP 470PF 10% 50VC615 1-107-820-11 CERAMIC CHIP 0.1uF 16VC616 1-128-964-11 TANTALUM CHIP 100uF 20% 6.3V

C617 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC618 1-164-866-11 CERAMIC CHIP 47PF 5% 50VC619 1-164-866-11 CERAMIC CHIP 47PF 5% 50VC620 1-115-156-11 CERAMIC CHIP 1uF 10VC621 1-104-847-11 TANTALUM CHIP 22uF 20% 4V

C622 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC623 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC624 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC625 1-107-820-11 CERAMIC CHIP 0.1uF 16VC626 1-107-820-11 CERAMIC CHIP 0.1uF 16V

C801 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC802 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC803 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC804 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC805 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C806 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC807 1-107-820-11 CERAMIC CHIP 0.1uF 16VC808 1-107-820-11 CERAMIC CHIP 0.1uF 16VC809 1-107-820-11 CERAMIC CHIP 0.1uF 16VC810 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

C811 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC812 1-107-820-11 CERAMIC CHIP 0.1uF 16VC814 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V

< CONNECTOR >

* CN501 1-785-877-21 HOUSING, CONNECTOR 4PCN502 1-784-342-21 HOUSING, CONNECTOR 2PCN503 1-573-924-11 CONNECTOR, FFC/FPC (ZIF) 15P

< DIODE >

D303 8-719-422-37 DIODE MA8051D304 8-719-422-37 DIODE MA8051D305 8-719-422-37 DIODE MA8051D306 8-719-422-37 DIODE MA8051D307 8-719-422-37 DIODE MA8051

D401 8-719-081-83 DIODE CRG01 (TE85L)D403 8-719-081-83 DIODE CRG01 (TE85L)D404 8-719-081-83 DIODE CRG01 (TE85L)D405 8-719-071-87 DIODE MA785-(TX) , SOD406 8-719-404-50 DIODE MA111-TX

D407 8-719-072-70 DIODE MA2ZD14001S0D408 8-719-081-83 DIODE CRG01 (TE85L)

D601 8-719-083-04 DIODE RSB6.8STE61D801 8-719-074-30 LED CL-190UR-CD-T (CHARGE)D803 8-719-056-66 DIODE 1SS378-TE85L

D804 8-719-083-04 DIODE RSB6.8STE61D805 8-719-083-04 DIODE RSB6.8STE61

< FERRITE BEAD/RESISTOR >


FB304 1-414-760-21 FERRITE 0uHFB401 1-500-451-11 FERRITE 0uHFB402 1-500-451-11 FERRITE 0uHFB403 1-216-864-11 METAL CHIP 0 5% 1/16WFB404 1-414-760-21 FERRITE 0uH


< IC >

IC301 6-700-702-01 IC TA2152FN (EL)IC402 8-759-694-91 IC SI-3048LSA-TLIC403 6-700-703-01 IC TB2130FIC404 6-701-860-01 IC TB2127AFN (EL)IC405 8-759-594-55 IC TC75S57F (TE85R)

IC601 8-752-410-68 IC CXD3029RIC602 6-700-994-01 IC MT4LC4M4B1TG-6IC801 6-800-479-01 IC T5AJ4-3HE0

< JACK >

J301 1-793-659-11 JACK, OPTICAL OUT (LINE OUT (OPTICAL))J302 1-815-088-61 JACK, HEADPHONE (i)J401 1-793-156-31 JACK, DC (EXT BATT, DC IN 4.5V)

< COIL >


L403 1-414-404-11 INDUCTOR 100uHL404 1-419-188-41 COIL, CHOKE 100uHL405 1-414-404-11 INDUCTOR 100uHL406 1-400-145-21 INDUCTOR 47uHL408 1-414-434-11 INDUCTOR 100uH


L502 1-400-145-21 INDUCTOR 47uHL503 1-400-145-21 INDUCTOR 47uHL602 1-414-521-11 INDUCTOR 10uHL604 1-414-521-11 INDUCTOR 10uHwww. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







9

D-EJ955

MAIN

< TRANSISTOR >

Q301 8-729-028-86 TRANSISTOR DTA143EUA-T106Q302 8-729-429-50 TRANSISTOR XP4312Q303 8-729-427-72 TRANSISTOR XP4501Q403 8-729-921-73 TRANSISTOR 2SD1781K-QRQ405 8-729-921-93 TRANSISTOR 2SB1182F5-QR

Q406 8-729-230-63 TRANSISTOR 2SC4116-YGQ407 8-729-029-14 TRANSISTOR DTC144EUA-T106Q412 8-729-056-20 TRANSISTOR TPC6001 (TE85R)Q414 8-729-026-53 TRANSISTOR 2SA1576A-T106-QRQ415 8-729-026-30 FET 2SJ346-TE85L

Q416 8-729-056-19 TRANSISTOR TPC6101 (TE85R)Q417 8-729-230-63 TRANSISTOR 2SC4116-YGQ418 6-550-075-01 TRANSISTOR UMZ8NTRQ419 6-550-063-01 TRANSISTOR UMF8NTRQ420 6-550-063-01 TRANSISTOR UMF8NTR

Q421 8-729-056-19 TRANSISTOR TPC6101 (TE85R)Q422 8-729-426-30 TRANSISTOR XP1213-TXE

< RESISTOR >

R101 1-218-977-11 RES-CHIP 100K 5% 1/16WR102 1-218-945-11 RES-CHIP 220 5% 1/16WR103 1-218-965-11 RES-CHIP 10K 5% 1/16WR104 1-218-953-11 RES-CHIP 1K 5% 1/16WR105 1-218-953-11 RES-CHIP 1K 5% 1/16W

R106 1-218-965-11 RES-CHIP 10K 5% 1/16WR107 1-218-947-11 RES-CHIP 330 5% 1/16WR108 1-218-990-11 SHORT 0R201 1-218-977-11 RES-CHIP 100K 5% 1/16WR202 1-218-945-11 RES-CHIP 220 5% 1/16W

R203 1-218-965-11 RES-CHIP 10K 5% 1/16WR204 1-218-953-11 RES-CHIP 1K 5% 1/16WR205 1-218-953-11 RES-CHIP 1K 5% 1/16WR206 1-218-965-11 RES-CHIP 10K 5% 1/16WR207 1-218-947-11 RES-CHIP 330 5% 1/16W

R208 1-218-990-11 SHORT 0R301 1-218-953-11 RES-CHIP 1K 5% 1/16WR302 1-218-953-11 RES-CHIP 1K 5% 1/16WR303 1-218-981-11 RES-CHIP 220K 5% 1/16W

(French)R303 1-218-983-11 RES-CHIP 330K 5% 1/16W

(EXCEPT French)

R304 1-218-981-11 RES-CHIP 220K 5% 1/16W(French)

R304 1-218-983-11 RES-CHIP 330K 5% 1/16W(EXCEPT French)

R305 1-218-990-11 SHORT 0R307 1-218-953-11 RES-CHIP 1K 5% 1/16WR308 1-218-941-81 RES-CHIP 100 5% 1/16W

R309 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR310 1-218-937-11 RES-CHIP 47 5% 1/16WR401 1-216-864-11 METAL CHIP 0 5% 1/16WR409 1-218-965-11 RES-CHIP 10K 5% 1/16WR410 1-218-977-11 RES-CHIP 100K 5% 1/16W

R413 1-216-298-00 METAL CHIP 2.2 5% 1/10WR414 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR415 1-218-990-11 SHORT 0

R416 1-216-298-00 METAL CHIP 2.2 5% 1/10WR417 1-218-961-11 RES-CHIP 4.7K 5% 1/16W

R418 1-218-973-11 RES-CHIP 47K 5% 1/16WR419 1-218-990-11 SHORT 0R420 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR421 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR422 1-208-927-11 METAL CHIP 47K 0.5% 1/16W

R423 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR424 1-216-864-11 METAL CHIP 0 5% 1/16WR425 1-216-864-11 METAL CHIP 0 5% 1/16WR426 1-216-864-11 METAL CHIP 0 5% 1/16WR428 1-216-864-11 METAL CHIP 0 5% 1/16W

R429 1-218-977-11 RES-CHIP 100K 5% 1/16WR432 1-216-864-11 METAL CHIP 0 5% 1/16WR435 1-218-975-11 RES-CHIP 68K 5% 1/16WR436 1-218-965-11 RES-CHIP 10K 5% 1/16WR437 1-218-977-11 RES-CHIP 100K 5% 1/16W

R439 1-216-864-11 METAL CHIP 0 5% 1/16WR440 1-218-981-11 RES-CHIP 220K 5% 1/16WR441 1-218-989-11 RES-CHIP 1M 5% 1/16WR442 1-218-990-11 SHORT 0R443 1-208-935-11 METAL CHIP 100K 0.5% 1/16W

R444 1-218-971-11 RES-CHIP 33K 5% 1/16WR445 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR446 1-216-864-11 METAL CHIP 0 5% 1/16WR447 1-216-864-11 METAL CHIP 0 5% 1/16WR448 1-218-989-11 RES-CHIP 1M 5% 1/16W

R449 1-218-990-11 SHORT 0R450 1-218-967-11 RES-CHIP 15K 5% 1/16WR452 1-218-989-11 METAL CHIP 1M 0.5% 1/16WR454 1-218-965-11 RES-CHIP 10K 5% 1/16WR455 1-218-971-11 RES-CHIP 33K 5% 1/16W

R456 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR457 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR458 1-218-969-11 RES-CHIP 22K 5% 1/16WR459 1-216-864-11 METAL CHIP 0 5% 1/16WR460 1-220-804-11 RES-CHIP 2.2M 5% 1/16W

R461 1-218-965-11 RES-CHIP 10K 5% 1/16WR463 1-216-864-11 METAL CHIP 0 5% 1/16WR465 1-216-864-11 METAL CHIP 0 5% 1/16WR467 1-208-947-11 METAL CHIP 330K 0.5% 1/16WR468 1-208-927-11 METAL CHIP 47K 0.5% 1/16W

R469 1-218-973-11 RES-CHIP 47K 5% 1/16WR470 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR471 1-208-719-11 METAL CHIP 33K 0.5% 1/16WR474 1-218-985-11 RES-CHIP 470K 5% 1/16WR477 1-218-985-11 RES-CHIP 470K 5% 1/16W

R478 1-218-989-11 RES-CHIP 1M 5% 1/16WR479 1-218-981-11 RES-CHIP 220K 5% 1/16WR482 1-218-949-11 RES-CHIP 470 5% 1/16WR483 1-218-945-11 RES-CHIP 220 5% 1/16WR484 1-218-977-11 RES-CHIP 100K 5% 1/16W

R485 1-218-989-11 RES-CHIP 1M 5% 1/16WR486 1-218-989-11 RES-CHIP 1M 5% 1/16WR487 1-218-989-11 RES-CHIP 1M 5% 1/16WR488 1-218-977-11 RES-CHIP 100K 5% 1/16WR489 1-218-990-11 SHORT 0

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99







10

D-EJ955

R490 1-218-989-11 RES-CHIP 1M 5% 1/16WR491 1-218-965-11 RES-CHIP 10K 5% 1/16WR492 1-218-990-11 SHORT 0R493 1-218-969-11 RES-CHIP 22K 5% 1/16WR601 1-218-969-11 RES-CHIP 22K 5% 1/16W

R602 1-218-985-11 RES-CHIP 470K 5% 1/16WR603 1-218-973-11 RES-CHIP 47K 5% 1/16WR604 1-218-989-11 RES-CHIP 1M 5% 1/16WR605 1-218-941-81 RES-CHIP 100 5% 1/16WR606 1-218-969-11 RES-CHIP 22K 5% 1/16W

R607 1-218-969-11 RES-CHIP 22K 5% 1/16WR608 1-218-969-11 RES-CHIP 22K 5% 1/16WR609 1-218-969-11 RES-CHIP 22K 5% 1/16WR610 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR611 1-218-959-11 RES-CHIP 3.3K 5% 1/16W

R612 1-218-965-11 RES-CHIP 10K 5% 1/16WR613 1-218-983-11 RES-CHIP 330K 5% 1/16WR614 1-218-977-11 RES-CHIP 100K 5% 1/16WR615 1-218-977-11 RES-CHIP 100K 5% 1/16WR618 1-218-965-11 RES-CHIP 10K 5% 1/16W

R619 1-218-971-11 RES-CHIP 33K 5% 1/16WR620 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR621 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR622 1-218-990-11 SHORT 0R623 1-218-939-11 RES-CHIP 68 5% 1/16W

R625 1-218-949-11 RES-CHIP 470 5% 1/16WR626 1-218-965-11 RES-CHIP 10K 5% 1/16WR627 1-218-990-11 SHORT 0R628 1-218-990-11 SHORT 0R629 1-218-990-11 SHORT 0

R630 1-218-990-11 SHORT 0R631 1-218-990-11 SHORT 0R632 1-218-990-11 SHORT 0R634 1-218-990-11 SHORT 0R635 1-216-803-11 METAL CHIP 33 5% 1/16W

R801 1-218-977-11 RES-CHIP 100K 5% 1/16WR802 1-218-977-11 RES-CHIP 100K 5% 1/16WR803 1-218-941-81 RES-CHIP 100 5% 1/16WR804 1-218-965-11 RES-CHIP 10K 5% 1/16WR805 1-218-989-11 RES-CHIP 1M 5% 1/16W

R806 1-218-965-11 RES-CHIP 10K 5% 1/16WR807 1-216-864-11 METAL CHIP 0 5% 1/16WR808 1-218-990-11 SHORT 0R811 1-218-965-11 RES-CHIP 10K 5% 1/16WR812 1-218-990-11 SHORT 0

R813 1-218-977-11 RES-CHIP 100K 5% 1/16WR814 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR815 1-218-953-11 RES-CHIP 1K 5% 1/16WR816 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR817 1-218-957-11 RES-CHIP 2.2K 5% 1/16W

R818 1-218-973-11 RES-CHIP 47K 5% 1/16WR819 1-218-973-11 RES-CHIP 47K 5% 1/16WR820 1-218-989-11 RES-CHIP 1M 5% 1/16WR821 1-208-715-11 METAL CHIP 22K 0.5% 1/16W

(EXCEPT French)R821 1-208-931-11 METAL CHIP 68K 0.5% 1/16W

(French)

R822 1-208-935-11 METAL CHIP 100K 0.5% 1/16W(French)

< SWITCH >

S801 1-762-078-11 SWITCH, SLIDE (HOLD)S802 1-762-078-11 SWITCH, SLIDE (AVLS)S803 1-762-078-11 SWITCH, SLIDE(G•PROTECTION)S804 1-762-805-41 SWITCH, PUSH (1KEY) (OPEN)S805 1-771-248-11 SWITCH, TACTILE (x/CHARGE)

S806 1-771-248-11 SWITCH, TACTILE (> N)S807 1-771-248-11 SWITCH, TACTILE (.)S808 1-771-248-11 SWITCH, TACTILE (VOL +)S809 1-771-248-11 SWITCH, TACTILE (VOL –)

< THERMISTOR >

TH401 1-804-616-21 THERMISTOR

< VARISTOR >



< VIBRATOR >

X601 1-795-003-21 VIBRATOR, CRYSTAL (16.9344MHz)

MAIN

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






11

D-EJ955

MEMO

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






D-EJ955

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.

Ver. Date Description of Revision

1.0 2001.11 New

1.1 2002.01 Addition of French and East European modelsChange of MAIN board (Suffix-12)Addition of the note about torque value to tighten screws for “UPPERLID (A) SUB ASSY” (page7) in “DISASSEMBLY” (SPM-01057)

www. xiaoyu163. com

QQ376315150 992894298

TEL 13942296513 992894298051513673QQ

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99

TE

L 1

39

42

29

65

13

QQ

37

63

15

15

0 8

92

49

82

99






d-ej955 c805 c809 r812 r811 r807 vdr8 fb803 d803 k a c440 + ... instruction manual. 4 getting...

Documents