CY8CKIT-062-WIFI-BT QUICK START GUIDE

PSOC® 6 WIFI-BT PIONEER KIT

• Ensure that SW5 on the CY8CKIT-062-WiFi-BT board is set to the middle (3.3V) position. This switch is in the middle of the board. • For this demo, you need to setup a WiFi network or a mobile hotspot.

• Peel off the sticker on the TFT screen to read the instructions displayed.

• Power the board by connecting it to your PC by using the provided USB cable through the USB-C connector (J10).

• The TFT screen displays the instructions to evaluate the pre-programmed code example: CE222494 PSoC 6 WICED WiFi Demo.

• The kit with the pre-programmed code example will create a WiFi network called “WICED Con�g”. Connect to this network using your PC/mobile device, see step 3.

Kit Contents:

1 PSoC® 6 WiFi-BT Pioneer Board

2 CY8CKIT-028-TFT Display Shield

3 USB Type-A to Type-C cable

4 Four jumper wires (four inches each)

5 Two proximity sensor wires (�ve inches each)

6 Quick Start Guide (this document)

www.cypress.com/CY8CKIT-062-WIFI-BT

21

PSOC® 6 WIFI-BT PIONEER KIT

• Click on the WiFi/mobile hotspot created in step 1. • Type in the password for the desired network and click Connect • The kit connects to this network, starts an http server and synchronizes to a time server. This can take 2 minutes to complete.

CY8CKIT-062-WIFI-BT QUICK START GUIDE

• Join the network “WICED Con�g” using your PC/mobile. The password is 12345678.• Open a web browser in your PC/mobile and go to http://192.168.0.1.

• Click on “Wi-Fi Setup” button.

• On your PC/mobile connect to the WiFi/mobile hotspot created in step 1. • Open a new web browser and go to the address shown on the TFT display.• The webpage shows the current time, date, light sensor voltage and duty cycle.• You can decrease or increase LED5 brightness by pressing the “Decrease” or “Increase” buttons on the webpage.• To evaluate additional features of this code example, install the kit software and refer to the code example CE222494 PSoC 6 WICED WiFi Demo.

• After connecting to the time server, the TFT screen displays the PWM duty cycle and the light sensor voltage. Light sensor voltage changes with intensity of ambient light. Swipe your �nger on the CapSense slider or press the CapSense buttons (BTN0 or BNT1) on the board to change PWM Duty Cycle and LED5 brightness.

3 4

5 6

CY8CKIT-062-WIFI-BT QUICK START GUIDE

1. USB PD output voltage availability indicator (LED7)

2. Battery charging indicator (LED6)

3. KitProg2 USB Type-C connector (J10)

4. Cypress EZ-PD™ CCG3 Type-C Port Controller

with PD (CYPD3125-40LQXI, U3)

5. KitProg2 programming mode selection button (SW3)

6. KitProg2 I/O header (J6)1

7. KitProg2 programming/custom application header (J7)1

8. External power supply connector (J9)

9. PSoC 6 user button (SW2)

10. KitProg2 application selection button (SW4)

11. Digilent® Pmod™ compatible I/O header (J14)1

12. Power LED (LED4)

13. KitProg2 status LEDs (LED1, LED2, and LED3)

14. PSoC 6 reset button (SW1)

15. PSoC 6 I/O header (J18, J19 and J20)

16. ArduinoTM Uno R3 compatible power header (J1)

17. PSoC 6 debug and trace header (J12)

18. ArduinoTM Uno R3 compatible PSoC 6

I/O header (J2, J3 and J4)

19. PSoC 6 program and debug header (J11)

1Footprints only, not populated on the board2Components at the bottom side of the board

20. CapSense proximity header (J13)

21. CapSense slider and buttons

22. PSoC 6 VDD selection switch (SW5)

23. Cypress 512-Mbit serial NOR Flash memory (S25FL512S, U4)

24. PSoC 6 user LEDs (LED8 and LED9)

25. RGB LED (LED5)

26. WiFi/BT module (LBEE5KL 1DX, U6)

27. Cypress serial Ferroelectric RAM (U5)1

28. WiFi-BT Antenna

29. Vbackup and PMIC control selection switch (SW7)2

30. PSoC 6 USB device Type-C connector (J28)

31. Cypress PSoC 6 (CY8C6247BZI-D54, U1)

32. PSoC 6 USB Host Type-A connector (J27)

33. ArduinoTM Uno R3 compatible ICSP header (J5)1

34. PSoC 6 power monitoring jumper (J8)2

35. KitProg2 (PSoC 5LP) programmer and debugger (CY8C5868LTI-LP039, U2)

36. Battery connector (J15)1,2

37. USB PD output voltage (9V/12V) connector (J16)1

PSoC 6 WiFi-BT Pioneer Board Details

3

12

45

6

7

8

9 10 11 12 13 14 15 16 17 18 19 21

2223

24

25

26

27

28

30 2931323334

20

15 15 181837 36 35

© 2018 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the property of their respective owners. 002-22582 Rev**

CY8CKIT-062-WIFI-BT QUICK START GUIDE

For the latest information about this kit, visit www.cypress.com/CY8CKIT-062-WIFI-BT

PSoC 6 WiFi-BT Pioneer Board Details

SWDIOSWDCLK

RESETGND

P5LP_VDD

VCC/P6_VDDGND/GND

SCK/P12_2MISO/P12_1MOSI/P12_0

SS/P12_5

P11_0P11_2P7_0P7_3P7_4P7_5P7_6P7_7

NCP6_VDD/IOREFRESET/RESETV 3.3/3.3 VV 5.0/5 VGND/GNDGND/GNDVIN/Vin

P15_4P1_6P0_7P0_3P0_2

P10_0/A0P10_1/A1P10_2/A2P10_3/A3P10_4/A4P10_5/A5P10_6P6_2P6_3P13_6

P9_0P9_1P9_2P9_3P9_4P9_5GNDP9_6P9_7P13_7

P6_0/SCLP6_1/SDAVREF/AREFGND/GNDP12_2/D13P12_1/D12P12_0/D11P12_3/D10P13_1/D9P13_0/D8

P12_4P12_5P12_6GNDP12_7P1_0P1_2P1_3P1_4P1_5

P0_2/D7P5_6/D6P5_5/D5P5_4/D4P5_3/D3P5_2/D2P5_1/D1P5_0/D0

P8_7P8_6P8_5P8_4P8_3P8_2P8_1P8_0

P13_2P13_3P13_4P13_5

P4_1P5_7P10_7GND

P5LP_VDDP15_1P15_2P15_3P12_5P3_4

P12_7P3_6

P15_5P0_1P12_0P3_0P12_1P3_5P12_6GND

Arduino Uno R3

LEGEND

PSoC 6 I/Os

KitProg2 I/OsDigilent Pmod