cs2000 spray apply tds - concrete waterproofing products · creteseal cs2000™ tds page !3 of !4...

Creteseal CS2000™ TDS

Page ! of !1 4 Supersedes Previous Versions Rev. 14.8

Packaging 5 US gal. (18L)

Color Clear

Solids 34%

Coverage 200 ft² / per US gal.

Application Temp 40º+ - 90º F

Pot Life None

Cure Times 2-4 hours (foot & equipment traffic)

Barrier Depth Up to 3.0mm

Barrier Type Calcium-silicate-hydrate gelled structure

Shelf Life 12 months if stored properly; Do not freeze

Reference Value

VOC Content ASTM D2369 None

Curing & Sealing ASTM C1315 Yes

Curing ASTM C309 Yes

Description Creteseal CS2000™ is a specialty blended solution applied to freshly-placed concrete that fixates the calcium hydroxide. Application is typically performed on the same day as the concrete placement or as soon as job site weather conditions allow. The product is sprayed on and evenly distributed with a soft-bristle broom until it is completely absorbed within the slab. Creteseal CS2000™ is designed to penetrate into the top portion of concrete floor slabs to form a moisture vapor and alkalinity control system.

CS2000™ also benefits as a curing method and may be used for slabs on grade, below grade or above grade wherever resilient flooring is specified. The system includes a company technical representative to oversee the installation for quality control and certification. CS2000™ is covered with a 15-year warranty against failure due to moisture vapor migration or moisture-born alkalinity.

Where to Use CS2000™ conforms to all state and federal VOC regulations, having zero VOC content. Besides be ing used in depar tment s to res and warehouses, the zero VOC content allows installation of the CS2000™ in schools, food stores, medical offices and hospitals.

Advantages CS2000™ is a pro-active solution for addressing excessive moisture vapor emission and alkalinity from damaging the future flooring materials. CS2000™ also benefits as a curing method and meets ASTM C309 & ASTM C1315. Construction traffic can resume as early as the following day after the CS2000™ application. CS2000™ Spray Apply system is more economical when compared to a retrofit system (systems applied after the concrete has been cured). CS2000™ is non-toxic, non-hazardous, low odor, and contains no volatile organic compounds, waxes, resins, solvents, acrylics,

epoxies, stearates, urethanes or oils and will not separate or plug applicator sprayers. CS2000™ is a water-based product, environmentally friendly, will not harm plants or animals and is easy to clean up.

Typical Data CS2000™ is compatible with the following flooring materials: Wood, Carpet, Ceramic Tile, VCT, Rubber, Terrazzo, Linoleum, Polymer Coatings, Most flooring mortar and mastics.

CS2000 Spray Apply TDS Creteseal CS2000 Spray Apply System Seals Concrete Against Water & Contaminate Intrusion & Is Warrantied For a Full 15 years

Call Concrete Waterproofing Products at (800) 278-4273 for Additional Information.

NOTES:

CS2000™ requires a

qualified Concrete

Waterproofing Products,

Inc. technician to be

present during the entire

application process in order

to comply with the 15-year

warranty. Always use and

follow recommended

procedures when handling

CS2000™.

WARRANTY:

CS2000 carries a full

system fifteen (15) year

warranty that includes all

labor and materials

necessary to replace or

repair flooring that fails due

to negative side moisture

vapor emission and

alkalinity migration from

the concrete slab.




Installation Normal Weather Conditions A Concrete Waterproofing Products technician must be on-site the day of the product application, usually the day of the concrete placement to train in application, assuring correct product application, document and return on every application thereafter to verify that proper procedures are followed. The onsite Concrete Waterproofing Products technician provides onsite technical services, quality control and certification.

CS2000™ Spray Apply system may be applied the day of the concrete pour or as soon as severe weather conditions permit, prior to any other chemical treatment. The CS2000™ spray apply system can be used for slabs on grade, below grade or above grade where resilient flooring such as sheet vinyl, vinyl composition tile, rubber, wood flooring, carpet, sports flooring, epoxy coatings and overlays. Apply CS2000™ to the concrete slabs as soon as final finishing operations are complete and the concrete has hardened sufficiently to sustain foot traffic without damage. Severe weather such as rain, snow, cold, excessive heat, wind, or job site conditions such as concrete not exposed to direct sunlight will affect the rate of concrete hydration and delay or change the CS2000™ application until a more acceptable time dictated by Concrete Waterproofing Products. Excessive heat, dry and windy weather will require an immediate follow up of water spray to aid in the penetration of the product and reduce the evaporation of the water-based CS2000™ sealer.

Using clean (uncontaminated) low-pressure hand pumps, spray the CS2000™ at the rate of 200 square feet per gallon. Broom product evenly over the substrate until product has completely penetrated the surface.

If within 2-hours after initial application areas are subjected to heavy rainfall and puddles occur, reapply CS2000™ product to these areas as soon as weather conditions permit. Extra product for reapplication will be provided at no cost by Concrete Waterproofing Products.

Hot Weather Conditions Job site conditions with temperatures over 90 degrees may require the applicator to pre-wet the concrete slabs with clean potable water.

Cold Weather Conditions Job site conditions must be 40 degrees and rising to properly apply the CS2000™. Cooler temperatures and indirect sunlight can delay the installation until more suitable site conditions permit. Our onsite technician will dictate when to apply in variable weather conditions.

Architecturally Finished Slabs Possible discoloration of the slab surface may occur if CS2000™ is used where exposed aggregate and colored slabs is specified. CS2000™ is designed for interior concrete slabs that are to receive floor coverings. Topical sealers that contain enough coloring effects and h ide the ac tua l s lab appearance a re recommended. Concrete Waterproofing Products cannot be responsible for concrete surface appearance when coated with a clear topical sealer.

Tilt-Up Construction Casting slabs where CS2000™ is to be applied should be prepared according to bond breaker manufacturer procedures, to al low the designated bond breaker product to perform. Concrete Waterproofing Products recommends a minimum of 48-hours cure time between the completed CS2000™ application and any type of concrete surface cleaning. Typically the bond breaker manufacturer requires a specific cleaning method prior to application of their product when installing over existing or p r e v i o u s l y c u r e d c o n c r e t e . C o n c r e t e Waterproofing Products recommends to fully pressure wash/mechanically scrub the concrete of all latent CS2000™ material and other cons t ruc t ion debr is thorough ly to the manufacturer requirements of the bond breaker material. Then allow the concrete to dry for 24hrs. Then apply the bond breaker per the manufacturers specifications.



Storage/Handling Product containers should be kept tightly sealed and stored in a shaded area between temperatures of 40° - 90° Fahrenheit. Avoid freezing. Should freezing of the product occur, please contact Concrete Waterproof ing Products. W h e n h a n d l i n g C S 2 0 0 0 ™ , C o n c r e t e Waterproofing Products recommends following OSHA standards. If splashed in eyes, flush thoroughly with water for 15-minutes. Prolonged excessive contact with skin should be avoided. Wash skin and clothes with water after using product. Do not take internally.

Requirements You have made the right choice; Creteseal CS2000™ is a proactive approach in controlling moisture vapor emission and alkalinity. Concrete Waterproofing Products wants to advise you that there are many conditions that are problematic to the successful installation and maintenance of your projects proposed flooring system. Please be aware, that Concrete Waterproofing Products cannot be responsible for flooring systems that fail due to non-moisture and non-alkalinity conditions. Please notify all involved parties to follow these requirements for a successful flooring installation:

• A Concrete Waterproofing Products Authorized Floor Consultant or Concrete Waterproofing Products Technical Services technician is required to be onsite during the application of CS2000™.

• Concrete slabs placed on grade or below grade must have a vapor retarder placed directly below the slabs with a minimum of 10mil thickness and permeance rating of 0.1 y, as described in ASTM F710-11 “Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring.”

Prior to floor covering installation, the following measures must be taken in order to maintain the Concrete Waterproofing Products 15-year warranty:

The surface area shall be prepared and cleaned of all latent material, dust, debris and any loose material that would compromise the adhesive bond as stated within ASTM F710 “Standard

Practice for Preparing Concrete Floors to Receive Resilient Flooring.”

Any concrete grinding or cutting from the slab surface will remove a significant amount of the CS2000™ treatment. Contact the Concrete Waterproofing Products office to obtain the re-treatment process.

The interior must be acclimated according to the i n d u s t r y s t a n d a r d s a n d t h e f l o o r i n g manufacturer’s requirements.

All cracks/joints/voids must be cleaned out and filled with a Concrete Waterproofing Products approved filler per ASTM F710 standard.

Before patching compounds are applied, check the concrete surface porosity to verify whether or not the patching material needs a primer.

Please check with each flooring manufacturer for their specific adhesive capabilities.




Specification Sheet: Creteseal CS2000™ Spray Apply System Division 3 (Cast in Place Concrete)

1.0 INTRODUCTION AND PURPOSE

1.1 Sealer / Hardener / Curing Compound: Concrete surface treatment applied the day of the concrete pour in lieu of other curing methods for concrete slabs either on grade, below grade or above grade receiving resilient flooring such as sheet vinyl, vinyl composition tile, rubber, wood flooring, carpet, epoxy coatings and overlays.

1.2 ASTM C1315 Type 1 Class A, ASTM C309 Type 1 Class A, penetrating product to have no less than 34% solids content, leaving no sheen, volatile organic compound (VOC) content rating as required to suit regulatory requirements. Product to have at least a 5 year documented history in controlling moisture vapor emission from damaging floor covering, compatible with all floor finish materials.

1.3 The product shall be CS2000™, Distributed by: Concrete Waterproofing Products Inc.

3531 East Miraloma Ave., Anaheim, CA 92806 Phone: 800-278-4273 Web: www.concretewaterproofingproducts.com

1.4 Epoxy or resin type vapor systems are not equal, as they are not compatible with flooring adhesives.

2.0 EXECUTION

2.1 Concrete Surface Treatment CS2000™ / Sealer / Hardener / Curing Compound applied the day of the concrete pour or as soon as harsh weather permits, prior to any other chemical treatments for concrete slabs either on grade, below grade or above grade receiving resilient flooring such as sheet vinyl, vinyl composition tile, rubber, wood flooring, carpet, epoxy coatings and overlays.

2.1.1 Concrete Waterproofing Products technician will be on site the day of the concrete pour to install or train in application, document and return on every application thereafter to verify that proper procedures are followed.

2.1.2 Apply CS2000™ to the concrete slabs as soon as final finishing operations are complete and the concrete has hardened sufficiently to sustain foot traffic without damage. Harsh weather such as rain, snow, cold, wind, or job site conditions such as concrete not exposed to direct sunlight will effect the rate of concrete hydration and delay Concrete Waterproofing Products application until a more suitable application time permits as directed by Concrete Waterproofing Products.

2.1.3 Spray Apply CS2000™ at the rate of 200 square feet per gallon. Broom product evenly over the substrate until product has completely penetrated the surface.

2.1.4 If within 2 hours after initial application areas are subjected to heavy rainfall and puddling occurs, reapply CS2000™ product to these areas as soon as weather condition permits. Allow additional cure time prior to floor placement.

3.0 WARRANTY

3.1 When a floor covering is installed on a below grade, on grade, or above grade concrete slab treated with CS2000™ according to manufacturer’s instructions, Concrete Waterproofing Products shall warrant the floor covering system against failure due to moisture vapor migration or moisture-born contaminates for a period of fifteen (15) years from the date of original installation. The warranty shall cover all labor and materials needed to replace all floor covering that fails due to moisture vapor emission & moisture born contaminates.


cs2000 spray apply tds - concrete waterproofing products · creteseal cs2000™ tds page !3 of !4...

Documents