Continuous Passive Motion

Hand Rehabilitation

Design Team

Project Sponsors: Bert Lariscy, Vanderbilt University EE graduate Crystal Bates, Occupational Therapist Jim Lassiter, MCN Chief Occupational Therapist

Group Members: Jonathan Webb ME Matthew Byrne ME Jennifer Hornberger BME Aaron Hadley BME

CPM Devices Continuous Passive Motion is a method of

rehabilitation following injury or surgery. Its main aim is to increase movement of the

joints while preventing overextension or further damage and to prevent the buildup of scar tissue.

CPM Market Injuries Typical surgeries

where CPM is needed post operatively: ankylosis of joints dislocation of fingers

and wrist sprain and strain of

wrist joints tissue replacement at

hand joints

Design Problem Problems with current

CPM device: fingers not allowed

independent motion thumb not a part of the

system heavy and bulky complex, difficult to set

up and use

Design Goals It is necessary to make a completely new

design that will incorporate independent finger motion, so as to allow for greater customization of rehabilitation.

It must also be lightweight and portable, so that a patient can treat themselves at home.

If possible, the thumb should be incorporated into the design in at least one dimension of movement.

Design Goals

Comparison Chart

Ligh

t

Inex

pens

ive

Not

Bul

ky

Less

Sca

ry

Long

bat

tery

life

(1

day)

Eas

ily o

pera

ted

Eas

ily p

ut o

n

Fas

hion

able

Unr

estr

ictiv

e

Light x 1 0 1 1 0 1 1 0 5 14%

Inexpensive 0 x 0 1 0 0 0 1 0 2 6%

Not Bulky 1 1 x 1 1 1 1 1 0 7 19%

Less Scary 0 0 0 x 0 0 0 1 0 1 3%

Long battery life (1 day) 0 1 0 1 x 1 1 1 0 5 14%

Easily operated 1 1 0 1 0 x 1 1 0 5 14%

Easily put on 0 1 0 1 0 0 x 1 0 3 8%

Fashionable 0 0 0 0 0 0 0 x 0 0 0%

Unrestrictive 1 1 1 1 1 1 1 1 x 8 22%Total 36 100%

Design Goals Following the evaluation of

the comparison chart, the following ranking of design objectives was obtained.

The following parameters are not necessary, but desirable in the final design.

Clearly, the portability aspect of the device is the most important to meet patient needs.

1 Unrestrictive 22%2 Not Bulky 19%3 Light 14%3 Long battery life (1 day) 14%3 Easily operated 14%6 Easily put on 8%7 Inexpensive 6%8 Less Scary 3%9 Fashionable 0%

Magnetic Field Technique Magnetic fields can control joints

of individual fingers.

By adjusting the strength of the magnet field, the speed of finger movement can be controlled.

The use of magnetic fields will keep the device lightweight and adjustable as only a power source and electric wiring will be needed.

The motion of the fields must be tested to find the extend to which the magnets can be controlled and how much current is needed

Solenoid Experiment

Results

The magnetic field induced by 12 Volts did not move the wooden rod. The magnetic field was not strong enough to hold a small screw to the

rod. Size restrictions of fingers will limit the N (loops/meter) value of the

solenoid equation. Currently, alternative types of solenoids are being researched to find if a

sufficient magnetic field can be developed from a small loop of coils.

Wire is wrapped around a rod, connected to a base through a hinge, and a current is passed through the wire to create a magnetic field. The induced magnetic field is attracted to the base magnet and should allow for control of the rod, resisted by a spring.

Solenoid Equation

B = μ*N*I Where μ=4π*10^-7

Mechanical Tension A series of small pulleys

and strings will be used to move the fingers.

These strings would be placed on the palm and back of the hand.

Each finger and even each joint could be moved independently.

A computer would control the length of the strings to set the desired position and allow for tension response.

ME Department’s Artificial Hand

The ME Department’s artificial hand uses similar tendon-like cables.

Tension returns the finger to an extended position.

The “tendons” are inside the finger, but for our CPM model the strings would have to be outside the body.

SMAs (Shape Memory Alloys) NiTinol (Nickel-Titanium alloy) and

other popular SMAs are being currently used in many fields and research is still being conducted to discover their full potential.

Would allow for a simple, lightweight design, and would form precisely with hand.

Unfortunately, would be difficult to deform and reform many times over and maintain precision. Also, the temperature required to activate it maybe unreasonable.

Inflation Initial inflation of the air/fluid-

filled bladder adjustable to fit all hand sizes.

Each finger attached to one of five individual compartments which can be inflated and deflated at different rates to allow for different range of motion in each finger.

Rate of inflation controlled through strain gauges and pressure sensors.

Problems How to provide feedback

so device will stop if there is too much resistance

Future Directions

Continue testing of ideas

Decide exactly which ideas to incorporate in design

Create prototype