CONCRETE RESURFACERRESURFACER FOR AGED OR SPALLED CONCRETE

DESCRIPTION:Cemix® Concrete Resurfacer is a high performance concrete resurfacing product for aged or spoiled concrete. It serves to resurface good quality concrete with a thin coating in situations where the surface is aged, stained, rain damaged, cracked or worn away. Its use serves to prevent the removal & replacement of good quality concrete. It is applied with a steel squeegee, trowel or broom brush finished.

TYPICAL APPLICATION/USES:• Resurfacing of aged concrete• Resurfacing of surface spalled concrete• Resurfacing of cracked concrete after undertaking crack repairs • Residential driveways• Patios• Footpaths• Shops, Restaurants & Cafes• Hospitals• Schools• Overcoat ‘ugly’ concrete repairs

ADVANTAGES:• Cost effective• High bond strength• Flexible• Durable

SUBSTRATE PREPARATION:Surfaces should be sound & rough to ensure a good bond. They should be uncoated & clean, free from all contaminants, loose particles, dirt, oil, mould, curing compounds, sealers & paints etc. Acid washing or honing & then water blasting is required to prepare the surface depending on substrate condition. Washing with soap & water blasting may also be required if oil is present. Holes, spalls, low spots, uneven and deteriorated surfaces should be patched with a suitable Cemix repair mortar and bonding agent. The better the substrate preparation & condition the better the end result. The concrete substrate should ideally be at least three months old.

CRACKS IN CONCRETE:Cracks in the concrete substrate must be well repaired with suitable products prior to product application. Seek technical advice if required.

MOVEMENT / CONTROL JOINTS:Honour any control joints in the concrete substrate – do not apply product over control joints. If required create control joints in substrate at suitable locations.

APPLICATION:Dampen concrete substrate with a light spray of water. Avoiding ponding, apply the first coat immediately after mixing the product. Use a suitable steel squeegee, trowel or brush to force product into the surface. After the first coat has completely dried, mix up a new batch of Resurfacer. Dampen the surface with a light spray of water and apply the second coat in the same manner. A third coat may be applied if required. If a broom finish is required, broom the surface immediately after the final coat of product has been applied. The total finish thickness should be approximately 2mm - 3mm.

IMAGE

20kg

CEMIX LTD19 ALFRED STREETONEHUNGA 1061 AUCKLAND NEW ZEALAND

0800 ASK CEMIXWWW.CEMIX.CO.NZ

CDS_0009 | CRS 020

MIXING:Mix full bags of product. Mix the product separately for each coat. Add water to product, not product to water. Mix the product with a drill & paddle thoroughly for at least 4 - 5 minutes. Mix to a pourable consistency. Maximum water addition is 4L of water per 20kg bag. Mix until all cement lumps have been broken down. Use product immediately. Mixing water temperature should ideally be between 15ºC - 22º C.

POST APPLICATION:Avoid rain damage until the product has set. Protect the product from freezing for at least one day.

COLOUR & STAINING:Contact Cemix® for advice on colouring & staining the product.

SEALING:To enhance surface appearance and increase durability, seal the surface the next day with a suitable Cemix clear sealer such as Pavseal (water based) or Driveseal (solvent based for external use only).

LIMITATIONS:Substrate Temperature - +5°C min. / +30°C max.Ambient Temperature - +5°C min. / +30°C max.Not to be used as a mortar for repairs >3mm deep.

SAFETY:Avoid contact with eyes & skin, both from wet & dry mix. Do not breathe in dust. Wear suitable protective clothing, gloves, eye protection & barrier cream. Wear a suitable dust mask. Wash thoroughly after handling & store any leftover material properly.

FIRST AID:Irrigate eyes & skin with plenty of water & seek medical advice immediately.

SPILLS AND LEAKS:Keep out of sewers & storm water drains & dispose of any leftover material as trade waste in accordance with local authority guidelines.

DISCLAIMER:Please Note: Recommendations and advice regarding the use of this product are to be taken as a guide only. Other than as appears on this products packaging, Cemix® LTD. does not give any warranty express or implied as to the suitability of this product for your particular use, because the usage of this product is beyond the control of Cemix® LTD. If you need advice concerning the use of suitability of this product for your particular application, please contact Cemix® LTD first. If this product is defective because of Cemix® LTD’s fault, please contact the supplier or Cemix® LTD. who will replace it at no cost.

TECHNICAL DATA:

Precaution:• Avoid rain damage until the product has set. Protect the product from freezing for at least one day.• Variations in colour & texture in the finished surface should be expected. • This product may not be suitable for certain very high wear applications. • Variations in colour & texture in the finished surface should be expected.

COVERAGE:Approximately 1m2 for every 2kg of product for two coats. Therefore 20kg will do approximately 10m2 for two coats. A rough substrate surface texture & additional coats will consume more product.

PACKAGING: Cemix® Concrete Resurfacer comes in 20kg bags.

STORAGE & SHELF LIFE:Store Cemix® Concrete Resurfacer Can be stored in its original container in a dry place well sealed for a period of twelve (12) months after production. Do not store opened bags & pails.

CLEANING:Clean all tools with water & brush immediately after use.

CEMIX LTD19 ALFRED STREETONEHUNGA 1061 AUCKLAND NEW ZEALAND

0800 ASK CEMIXWWW.CEMIX.CO.NZ

STRENGTH:

APPEARANCE:

APPLICATION TEMP:

WORKING TIME:

25MPa @ 28 days

Sand / Cementitious

5°C - 30°C

40mins @ 20oC

The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations may occur on site.