chauncey k. wilmore - macon-bibb
TRANSCRIPT
Macon-Bibb County Government Procurement Department
Government Center 700 Poplar Street, Suite 308
Macon, Georgia 31201 (478) 803-0550
Fax (478) 751-7252
Chauncey Wilmore Senior Procurement Officer
November 19, 2015
ADDENDUM # 1
To: ALL PROSPECTIVE FIRMS Re: INVITATION FOR BIDS: 16-017-CW Log Cabin Drive Construction The Invitation for Bids, referenced above, is modified as follows:
1. A revised bid schedule is provided
a. Added pay item for Sod
b. Deleted pay item for Maintenance of Permanent Grassing
2. Revised Technical Specs
a. Section 700.4A – corrected method of payment for Permanent Grassing to be Lump Sum
b. Section 700.5A – Revised payment method and schedule for Permanent Grassing 3. Revised Construction Plan Sheets 1.0, 3.2, 4.4, 4.8, 4.9, and 5.2
Please incorporate this change into the Invitation for Bid and acknowledge receipt of this addendum on your bid form.
Sincerely,
Chauncey K. Wilmore Chauncey K. Wilmore Senior Procurement Officer
LOG CABIN DRIVE ENHANCEMENT PROJECT - BID SCHEDULE
ITEM NO. DESCRIPTION UNIT QUANTITY UNIT PRICE AMOUNT
150‐1000 TRAFFIC CONTROL LS LS $ $
163‐0232 TEMPORARY GRASSING LS LS $ $
163‐0240 MULCH TN 6 $ $
163‐0300 CONSTRUCTION EXIT EA 3 $ $
163‐0529CONSTRUCT AND REMOVE
TEMPORARY BALED STRAW CHECK EA 30 $ $
163‐0541CONSTRUCT AND REMOVE ROCK
FILTER DAMSEA 2 $ $
163‐0542CONSTRUCT AND REMOVE STONE
FILTER RINGEA 1 $ $
163‐0550CONSTRUCT AND REMOVE INLET
SEDIMENT TRAPEA 14 $ $
165‐0010MAINTENANCE OF TEMPORARY SILT
FENCE, TP ALF 309 $ $
165‐0030MAINTENANCE OF TEMPORARY SILT
FENCE, TP CLF 660 $ $
165‐0071MAINTENANCE OF SEDIMENT
BARRIER ‐ BALED STRAWEA 30 $ $
165‐0101MAINTENANCE OF CONSTRUCTION
EXITEA 3 $ $
165‐0105MAINTENANCE OF INLET SEDIMENT
TRAPEA 14 $ $
165‐0110MAINTENANCE OF ROCK FILTER
DAMEA 1 $ $
165‐0111MAINTENANCE OF STONE FILTER
RINGEA 1 $ $
167‐1000WATER QUALITY MONITORING AND
SAMPLINGMO 6 $ $
167‐1500 WATER QUALITY INSPECTIONS MO 6 $ $
171‐0010 TEMPORARY SILT FENCE, TYPE A LF 309 $ $
171‐0030 TEMPORARY SILT FENCE, TYPE C LF 660 $ $
210‐0100 GRADING COMPLETE LS LS $ $
310‐5080GR AGGREGATE BASE CRS, 8 INCH,
INCL MATLSY 1200 $ $
402‐3103
RECYCLED ASPH CONC 19 MM
SUPERPAVE, TYPE II, GP 2 ONLY,
INCL BITUM MATL & H LIME
TN 170 $ $
Page 1 of 3
LOG CABIN DRIVE ENHANCEMENT PROJECT - BID SCHEDULE
ITEM NO. DESCRIPTION UNIT QUANTITY UNIT PRICE AMOUNT
402‐3121
RECYCLED ASPH CONC 12.5 MM
SUPERPAVE, GP 2 ONLY, INCL
BITUM MATL & H LIME
TN 1147 $ $
441‐0016 DRIVEWAY CONCRETE, 6" THICK SY 570 $ $
441‐0104 CONCRETE SIDEWALK, 4 INCH SY 2400 $ $
441‐4020 CONCRETE VALLEY GUTTER, 6 INCH SY 244 $ $
441‐6012CONC CURB & GUTTER, 6 IN X 24 IN,
TP 2LF 1376 $ $
500‐3800 18" CONCRETE HEADWALL EA 2 $ $
500‐9999CLASS "B" CONC, BASE OR
PAVEMENT WIDENINGCY 154 $ $
550‐1180 STORM DRAIN PIPE, RCP, 18 IN LF 1239 $ $
550‐2180SIDE DRAIN PIPE (DRIVEWAY PIPES,
BCCMP), 18 INLF 212 $ $
550‐3318SAFETY END SECTION 18 IN, STORM
DRAIN, 4:1 SLOPEEA 3 $ $
550‐3418SAFETY END SECTION 18 IN, SIDE
DRAIN, 4:1 SLOPEEA 10 $ $
603‐2024 STN DUMPED RIP RAP, TP1, 24 IN SY 250 $ $
611‐8050 ADJUST SS MANHOLE TO GRADE EA 12 $ $
611‐8120ADJUST WATER METER BOX TO
GRADEEA 10 $ $
641‐1200 GUARDRAIL, TP W LF 20 $ $
641‐5006 GUARDRAIL ANCHORAGE, TP 6 EA 2 $ $
641‐5012 GUARDRAIL ANCHORAGE, TP 12 EA 2 $ $
653‐0120THERMOPLASTIC PAVEMENT
MARKING, ARROW, TYPE 2EA 2 $ $
652‐2502SOLID TRAFFIC STRIPE, 5 IN,
YELLOWLS LS $ $
653‐6006THERMOPLASTIC TRAFFIC STRIPING,
YELLOWLS LS $ $
660‐2042ADJUST SANITARY SEWER LATERAL,
4 IN.LF 400 $ $
668‐1100 CATCH BASIN, GP 1 EA 8 $ $
Page 2 of 3
LOG CABIN DRIVE ENHANCEMENT PROJECT - BID SCHEDULE
ITEM NO. DESCRIPTION UNIT QUANTITY UNIT PRICE AMOUNT
668‐2100 DROP INLET, GP 1 EA 2 $ $
670‐9810ADJUST WATER SERVICE LINE TO
GRADEEA 10 $ $
700‐6910 PERMANENT GRASSING LS LS $ $
700‐6911 DELETED
700‐9300 SOD SY 1450 $ $
716‐1000EROSION CONTROL MATS,
WATERWAYSSY 1,255 $ $
716‐2000 EROSION CONTROL MATS, SLOPES SY 620 $ $
1300‐1.07 AS‐BUILT DRAWINGS LS LS $ $
$
PED 001
PEDESTRIAN BRIDGE
FOUNDATIONS, DESIGN AND
CONSTRUCTION, COMPLETE
LS LS $ $
PED 002
PEDESTRIAN BRIDGE STRUCTURE,
DESIGN AND CONSTRUCTION,
COMPLETE
LS LS $ $
$
RDBR‐001REPAIR HEADWALL SPALL ON BOTH
ENDS OF BRIDGELS LS $ $
RDBR‐002REPAIR EROSION AROUND BOTH
ABUTMENTSLS LS $ $
535‐1105PAINT EXIST STEEL STRUCTURE,
BRIDGE ID 021‐0170‐0LS LS $ $
RDBR‐003REPAIR DAMAGED CONCRETE
BRIDGE RAILINGLS LS $ $
RDBR‐004
MISCELLANEOUS MAINTENANCE
ITEMS (SEE STATEMENT OF WORK,
01005, Part 1, 1.01.C.e.)
LS LS $ $
$
$
ROADWAY ENHANCEMENT ITEMS SUBTOTAL
TOTAL PROJECT BID PRICE
ROADWAY BRIDGE MAINTENANCE SUBTOTAL
PEDESTRIAN BRIDGE
ROADWAY BRIDGE (ID 021‐0170‐0) OVER ROCKY CREEK REPAIR AND MAINTENANCE
ROADWAY BRIDGE MAINTENANCE SUBTOTAL
Page 3 of 3
Answers to Questions:
Question: I looked at the plans and specs and both talk of sod and grassing. I do see where some grassing is going but nothing with any sod. Also in the plans it shows a list of several different species of plant material, but it doesn’t show where they are going? There is no plan for that. Do we know an approx...? Amount of quantities for these items? I am assuming sod and trees and shrubs are paid on unit quantity but I was just wondering because there is no landscape plan, or at least I didn’t see it. If you could let me know that on the plant material and quantities and then also where in the plans it shows if an at all. Thanks for your help and I look forward to working with you.
Answer: Sod has been added to the bid schedule and the areas where it is required is shown on Sheet 4.8. See bid amendment 1. See section 700.3.05 on page 115 for the type of grassing allowed. Permanent grassing requires common Bermuda grass in areas that will be mowed regularly and allows for Interstate Lespedeza or Crown Vetch in those sloped areas that will not be mowed regularly. Quantities should be calculated by the contractor based on the disturbed areas. Payment of all grassing is covered in the bid schedule.
Question: The 9.5 mm pay item needs to be 19 mm.
Answer: This has been changed. See bid amendment 1.
Question: I don’t see any specifications on the grassing maintenance item for 6 months. Can you please provide a clear description of scope for this item?
Answer: We have eliminated the requirement for grassing maintenance, but this should not be confused with the requirement to establish the grass. Note that follow-on requirements in the specifications for plant establishment in the spring are beyond the performance period of 180 days to construct the project and provide beneficial occupancy to Macon-Bibb. Performance is required at this point until satisfactory establishment of grass is achieved. Liquidated damages do not apply for this work.
Page 1
Section 150—Traffic Control
150.1 General Description This section describes:
Installation and maintenance of traffic control devices during construction Projects let to Contract by Macon‐
Bibb County.
Guidelines and procedures for reducing the speed limit in areas where workers are present, or where roadway
or roadside conditions create a potential hazard from construction or maintenance activities.
Temporary speed limit reductions in Work zones must comply with Georgia Law (Code Section 40‐6‐188).
150.2 Definitions
The traffic control plan is defined in the Specifications and the current edition of the Manual on Uniform Traffic
Control Devices (MUTCD).
Traffic control devices referred to in this section are devices specified in the Contract and the MUTCD and are
used by a Contractor to regulate, warn, or guide traffic through a Project under construction.
150.3 Related References
Referenced Documents
Manual on Uniform Traffic Control Devices (MUTCD) Official Code of Georgia Annotated (OCGA): 40‐6‐188
Georgia Utilities Coordinating Committee (GUCC) Manual (also known as Manual on Traffic Control Procedures
for Utilities)
150.4 Submittals
A. Contractor Responsibilities
1. Prior to construction, the Contractor shall submit a detailed staging and traffic control plans for
performing specific areas of the Work including but not limited to all traffic shifts, bridge maintenance,
lane closures or other activities that disrupt traffic flow. A Plan of operation and sequence of Work,
along with any appropriate Provisions for traffic control, shall be submitted to the Macon‐Bibb County
Engineer for prior approval before beginning any Work. NOTE: The Contractor’s primary responsibility
is for safe passage of pedestrian and vehicular traffic through the Work zone with minimal confusion
and traffic flow disruption.
1. Before construction, inspect the initial installation of the traffic control devices.
2. Periodic inspections of the conditions of the devices and their effectiveness in the work zone.
a. If problems are encountered, the Macon‐Bibb County Engineer can assist with solutions to
improve traffic control.
b. Document inspection in Contract Diary.
3. Daytime and Nighttime inspections should be made as conditions warrant.
4. Observe traffic movements while operating under the traffic control devices.
5. Report lane closures and openings as follows:
a. Report Projects that routinely require a lane closure only once, unless the operation changes,
such as stopping Work for a long period of time or switching lanes.
Section 150—Traffic Control
Page 2
b. Report intermittent lane closures each time they are closed to keep the Macon‐Bibb County
Engineer aware of the actual Project conditions.
6. Notify the Macon‐Bibb County Engineer when unusual situations arise that requires a lane closure
7. The Contractor shall not begin a major traffic shift until the Macon‐Bibb County Engineer has approved
the following:
a. A set of traffic control details
b. Any proposed lane shifts, closures, or traffic pacing
c. The removal, storage, and protection of any existing street lights, signs, or sign supports
150.6 Construction Requirements
A. Personnel The Contractor shall designate a qualified Worksite Traffic Control Supervisor (WTCS) who shall be
responsible for administering the traffic control Plan according to the Contract.
1. Worksite Traffic Control Supervisor (WTCS):
Be responsible for selecting, installing and maintaining all traffic control devices in accordance with the Plans,
Specifications, Special Provisions and the MUTCD.
Have appropriate training in safe traffic control practices in accordance with Part VI of the MUTCD.
Ensure that all traffic control devices are effective and comply with the Traffic Control Plan.
Exercise full authority to act on behalf of the Contractor in administering the Traffic Control Plan.
Be available on a 24‐hour basis and be able to respond effectively to an emergency within 45 minutes of
notification.
Supervise the installation of the traffic control devices before construction.
Review any modifications to the Traffic Control Plan before submitting them to the Macon‐Bibb County
Engineer.
Inspect the traffic control devices on a regular basis to ensure that they meet the requirements of the Traffic
Control Plan.
Monitor the Work to ensure that all potential hazards are kept clear of the traffic and that dust, mud, and debris
do not interfere with normal traffic operations or adjacent property.
NOTE: No Work shall begin on any phase of the Project unless the appropriate traffic control devices have
been placed.
1. Flagger
Flaggers shall be provided as required to handle traffic.
All flaggers shall meet the requirements of the MUTCD and shall have received training and a certificate upon
completion of the training from a GDOT approved training program.
Failure to provide a certified flagger as required will be reason for the Macon‐Bibb County Engineer to suspend
work involving the flagger(s) until the Contractor provides certified flagger(s).
Section 150—Traffic Control
Page 3
Flaggers must have proof of certification and a valid identification available when performing flagger duties.
Flaggers shall wear high‐visibility clothing in compliance with MUTCD.
Flaggers shall use a Stop/Slow paddle meeting the requirements of the MUTCD for controlling traffic.
Flags used shall meet the minimum requirement of the MUTCD.
B. Equipment 1. Traffic Control Devices
All traffic control devices used during the construction of a project shall meet the Standards utilized in the
MUTCD, and shall comply with the requirements of these Specifications, Project Plans, and Special Provisions. All
traffic control devices used on any project shall be NCHRP 350 compliant.
2. Reflectorization Requirements
a. Omitted
b. All other Highways:
All reflectorization for permanent mounting height construction signs (Black on Orange), object markers, and
channelization devices shall meet the reflectorization requirements of Section 913, Type III or IV unless
otherwise specified.
Portable signs which have rigid or flexible sign blanks shall have Type V diamond grade sheeting.
Warning signs (W3‐1a) for stop conditions that have rumble strips located in the travelway shall be reflectorized
with Type V fluorescent yellow diamond grade sheeting.
All other signs shall meet the requirements of Type I unless otherwise specified.
150.7 Construction
A. Inspection
During the day and night, the Macon‐Bibb County Engineer will periodically inspect the traffic control devices
and determine their effectiveness in the Work zone. The frequency of these inspections will depend on the type
and volume of Work. During an inspection, observe traffic movement while the devices are operating.
C. Restrictions
The Macon‐Bibb County Engineer may restrict construction operations if the Work would seriously disrupt traffic
flow when unusual traffic conditions exist, such as during holidays and bad weather.
D. Determining Reduced Speed Limits
Macon‐Bibb County is responsible for determining the appropriate speed limit reduction for all roadways under
its supervision.
A temporary speed reduction zone will be established for a section of roadway according to an identified need
such as:
When workers are near a travel lane.
Section 150—Traffic Control
Page 4
When Work is being performed near a travel lane.
When Temporary concrete barrier is located less than 2 feet from the travelway.
When the Contractor’s request is justified.
E. Work Zone Speed Limits
The minimum reduction of the posted speed limit will be no less than 10 mph and a maximum reduction of no
greater than 20 mph.
Do not use regulatory speed limit signs (black on white) to reduce speeds to less than 10 mph below the original
speed limit unless one or more of the following conditions exist in the Work zone:
Sharp cresting vertical curves
Horizontal shifts
Work is performed near a travel lane
F. Signing Requirements for reduced speed limits
To temporarily reduce the speed limit in a Work zone, use the following guidelines.
1. Erect a standard R2‐5a (Reduced Speed Ahead) sign a minimum of 600 ft in advance of the reduced speed
zone.
2. Erect a standard R2‐1 (Speed Limit XX) sign a minimum of 600 ft in advance of the beginning of the reduced
speed zone, if the speed limit will be reduced a total of 20 mph. This sign reduces the speed in 10 mph (16 kph)
increments.
3. Erect a black on white regulatory R2‐Special (Work Zone/Speed Limit XX/Minimum Fine $100) sign 600 ft past
the previous sign erected in Step 1 or 2.
4. Erect intermediate R2‐1 (Speed Limit XX) signs at intervals not exceeding one mile within the reduced speed
zone.
5. Erect a standard R2‐1 (Speed Limit XX) sign 600 ft past the Work zone. This sign shall post the normal speed
limit for the roadway.
6. Cover or remove all existing speed limit signs while the temporary reduction in the speed limit is in effect.
All signs will be erected in compliance with the minimum requirements of the MUTCD.
G. Documentation
The Contractor shall record the following:
The date and time that each temporary speed reduction zone is installed and removed
The limits of the zone
The traffic direction, if applicable
Section 150—Traffic Control
Page 5
H. Portable Changeable Message Signs When using a Portable Variable Message Sign (PCMS) on a Project, place
the PCMS ahead of the construction activity or road condition to prepare the motorist. Do not place the PCMS in
permanent location miles in advance of the Work zone. The PCMS message should be concise and meaningful.
Display messages no more than two flashes as described below: (One flash is desirable, motorists may not see
nor comprehend longer messages.)
The first flash should direct the motorist to take a specific action, such as MERGE/RIGHT, KEEP/RIGHT, or
REDUCE/SPEED.
The second flash, if necessary, should inform the motorist of road conditions, such as LEFT/LANE/CLOSED,
LANE/NARROWS/AHEAD, SHOULDER/DROP/OFF, WATER/IN/ROAD or TRUCKS/IN AND OUT.
Do not use confusing or frightening messages such as USE CAUTION, HAZARD AHEAD, or DANGER. Also, avoid
messages such as BUCKLE/UP or DRIVE/SAFELY that diminish the impact of important messages. When the
PCMS is not needed, turn off the sign and remove it from the roadside.
The Macon‐Bibb County Engineer reserves the right to require additional flaggers, signs, warning lights,
channelization devices and other safety devices as may be necessary to properly protect, warn and safeguard
the traveling public. Continued failure of the contractor to comply with the requirement of this or any other
related section will result in the Engineer issuing a written order to stop work (i.e. Stop Work Order). Upon
issuance of a stop work order, all work on the right of way will be suspended, except erosion control and traffic
control, until corrective actions or deficiencies are addressed, and the Engineer issues a written resume work
order.
150.8 Measurement When listed in the Contract, payment for Traffic Control will be made at the Lump Sum
price bid, which will include all traffic control not paid for separately, and will be paid as follows: For each
progress payment requested, the total Project percent complete minus the previous payments will be paid,
not to exceed 100 (one–hundred) percent.
Page 6
Section 163—Miscellaneous Erosion Control Items
163.1 General Description
This work includes constructing and removing:
Baled straw erosion checks
Temporary Grass
Temporary Mulch
Temporary Ditch Checks
Construction Exits
Inlet Sediment Traps
Other temporary erosion control structures shown on the Plans or directed by the Engineer
A. Baled Straw Erosion Checks
Construct baled straw erosion checks according to the Plan details.
B. Temporary Grass
Use a quick growing species of temporary grass such as rye grass, millet, or a cereal grass suitable to the
area and season.
Use temporary grass in the following situations:
To control erosion where permanent grassing cannot be planted. The Engineer will direct the
planting.
To protect an area for longer than temporary mulch is expected to last (60 calendar days).
C. Temporary Mulch
When stage construction or other conditions prevent completing a roadway section continuously, apply
temporary mulch to control erosion for 60 calendar days or less.
Use temporary mulch on erodible areas on or off the Right of Way, including borrow pits, temporary
haul roads, or waste areas. Apply mulch as follows:
1. Plant temporary grass on areas stabilized only with temporary mulch. Mulch the area
again after 60 calendar days.
2. Uniformly spread the mulch over the designated areas from 2 in to 4 in (50 mm to 100
mm) thick.
3. After spreading the mulch, walk in the mulch by using a tracked vehicle (preferred
method), empty sheep foot roller, light discing, or other means that preserves the
finished cross section of the prepared areas. The Engineer will approve of the method.
4. Place temporary mulch on slopes as steep as 2:1 by using a tracked vehicle to imbed the
mulch into the slope.
Section 163—Miscellaneous Erosion Control Items
Page 7
5. When grassing operations begin, leave the mulch in place and plow the mulch into the
soil during seed bed preparation. The mulch will become beneficial plant food for the
newly planted grass.
6. Place mulch to protect the newly planted grass. This mulch is required in addition to the
mulch specified in step 5.
D. Temporary Ditch Checks
Temporary ditch checks shall be constructed and placed according to Plan details. Temporary ditch
checks may be constructed of stone plain rip rap.
Place plastic filter fabric on ditch section before placing rip rap.
Temporary ditch checks shall be cleaned of sediment when 1/2 the height of the temporary ditch check
has been reached. They remain in place until the permanent ditch protection is in place or being
installed and the removal is approved by the Engineer.
These ditch checks may remain in place to aid in establishing permanent grass in vegetated waterways,
if approved by the Engineer.
E. Construction Exits
Locate construction exits at any point where vehicles will be leaving the project onto a public roadway.
Install construction exits at the locations shown in the plans and in accordance with plan details.
F. Inlet Sediment Trap
Inlet sediment traps consist of a temporary device placed around a storm drain inlet to trap sediment.
An excavated area adjacent to the sediment trap will provide additional sediment storage.
Inlet sediment traps may be constructed of Type C silt fence, plastic frame and filter, hay bales, baffle
box, or other filtering materials approved by the Engineer.
Construct inlet sediment traps according to the appropriate specification for the material selected for
the trap.
Place inlet sediment traps as shown on the Plans.
163.3 Measurement
A. Temporary Grass
Temporary grass is measured for payment by lump sum, including all required lime.
B. Temporary Mulch
Temporary mulch is measured for payment by the ton. The weight for measurement will be the product
of the number of bales used and the average weight per bale as determined on scales provided by the
contractor or state certified scales. The contractor shall provide written documentation to the Engineer
as to the average weight of the bales.
Section 163—Miscellaneous Erosion Control Items
Page 8
C. Baled Straw Erosion Checks
Baled straw erosion checks are measured by each. Type “B” temporary silt fence is measured as baled
straw when substituted by the Contractor or the Engineer.
D. Omitted
E. Construction Exits
Construction exits are measured per each which will include all work necessary to construct the exit
including the required geotextile fabric placed beneath the aggregate.
F. Inlet Sediment Trap
Inlet sediment traps, regardless of the material selected, are measured per each which includes all work
necessary to construct the trap including any incidentals and providing the excavated area for sediment
storage.
163.5 Payment
A. Temporary Grass
Temporary Grass is paid for by the lump sum. Payment is full compensation for all equipment, labor,
ground preparation, materials, fertilizer, mulch, and other incidentals including Lime.
B. Temporary Mulch
Temporary mulch is paid for by the ton. Payment is full compensation for all materials, labor,
maintenance, equipment and other incidentals.
G. Baled Straw Erosion Checks
Baled straw erosion checks, complete in place and accepted is paid for at the Contract Unit Price bid.
Payment is full compensation for constructing, and removing (when directed) the straw checks.
When the Contractor substitutes a Type “B” silt fence for baled straw erosion checks, or when the
Engineer directs this substitution, payment is made at the bid price per each for baled straw erosion
checks.
H. Omitted
I. Construction Exits
Construction exits are paid for per each. Payment is full compensation for all materials including the
required geotextile, construction, and removal.
Miscellaneous Erosion Control Items
J. Omitted
K. Inlet Sediment Trap
Section 163—Miscellaneous Erosion Control Items
Page 9
Inlet sediment traps are paid for per each. Payment is full compensation for all materials, construction,
and removal.
If temporary erosion control measures are required due to Contractor negligence, carelessness, or
failure to install permanent controls as part of the work as scheduled, the Contractor shall perform such
work at no additional expense to Macon‐Bibb County.
If the Contractor secures his or her own borrow pit, erosion control measures will be at his or her
expense.
The Items in this Section (except temporary grass and temporary mulch) are made as partial payments
as follows:
When the item is installed and put into operation the Contractor will be paid 75 percent of the
Contract price.
When the Engineer instructs the Contractor that the Item is no longer required and is to remain
in place or is removed, whichever applies, the remaining 25 percent will be paid.
Payment is made under:
Item No. 163 Construct and remove baled straw erosion check__ Per linear foot
Item No. 163 Construct and remove temporary ditch checks__ Per each
Item No. 163 Construct and remove construction exits Per each
Item No. 163 Construct and remove inlet sediment trap Per each
Item No. 163 Temporary Grass Lump Sum
Item No. 163 Temporary Mulch Ton
Page 10
Section 165—Maintenance of Temporary Erosion and Sedimentation
Control Devices
165.1 General Description
This work consists of providing maintenance on temporary erosion and sediment control devices,
including but not limited to the following:
Silt fence
Check dams
Silt retention barriers
Rock filter dams
Stone filter berms
Stone filter rings
It also consists of removing sediment that has accumulated at the temporary erosion and sediment
control devices.
General
As a minimum, clean the sediment from all temporary erosion control devices (except sediment basins)
installed on the project when one half the capacity, by height, depth or volume has been reached.
Clean the sediment from all temporary sediment basins installed on a project when one third the
capacity of the storage volume has been filled.
Handle sediment excavated from any erosion or sediment control device in one of the following ways:
Remove sediment from the immediate area and immediately stabilize it to prevent the material
from refilling any erosion or sediment control device.
Place and mix it in the roadway embankment, or waste it in an area approved by the Engineer.
Repair or replace at no cost to Macon‐Bibb County, any erosion or sediment control devices that
are not functioning properly or are damaged due to negligence or abuse.
A. Temporary Silt Fence
Maintenance of Temporary Silt Fence consists of furnishing all labor, tools, materials, equipment and
necessary incidentals to remove and dispose of accumulated sediment down to the original ground line
(0 % filled). Also included is the removal of sediment accumulations (“filtercake”) on the fabric by
tapping the fabric on the downstream side.
B. Check Dams (all types)
Maintenance of Temporary Erosion Control Check Dams shall consist of all labor, tools, materials,
equipment and necessary incidentals to remove and dispose of accumulated sediment down to the
original ground line (0% filled). This item also includes the removal of any material deposited in sump
Section 165 – Maintenance of Temporary Erosion and Sedimentation Control Devices
Page 11
holes. When applicable, this item will include the removal of sediment accumulations on the fabric by
tapping the fabric on the downstream side, or from the baled straw by similar means.
C. Sediment Barrier (baled straw)
Maintenance of sediment barrier (baled straw) consists of furnishing all labor, tools, materials,
equipment and necessary incidentals to remove and dispose of accumulated sediment down to the
original ground line (0 % filled). Also included is the removal of sediment accumulations on the bales by
tapping.
D. Triangular Silt Barrier
Maintenance of Triangular Silt Barrier consists of all labor, tools, materials, equipment and necessary
incidentals to remove and dispose of accumulated sediment down to the original ground line (0% filled).
E. Construction Exit:
Maintenance of the construction exit consists of all labor, tools, materials, equipment and incidentals,
including additional stone and geotextile fabric as required to prevent the tracking or flow of soil onto
public roadways. This includes, scarifying existing stone, cleaning existing stone, or placement of
additional stone.
Cleaning of the construction exit by scraping and/or brooming only will not be measured for payment.
F. Inlet Sediment Trap
Maintenance of inlet sediment traps consists of all labor, tools, materials, equipment and necessary
incidentals to remove and properly dispose of accumulated sediment in the trap and/or the excavated
area adjacent to the trap. It also includes any maintenance that is required to remove sediment
accumulations (“filtercake”) from the material selected to construct the inlet sediment trap.
G. Rock Filter Dams
Maintenance of rock filter dams consists of all labor, tools, materials, equipment, and necessary
incidentals to remove and dispose of accumulated sediment down to the original ground line (0% filled).
This item also includes the removal of any material deposited in sump holes.
H. Stone Filter Berms
Maintenance of stone filter berms consists of all labor, tools, materials, equipment, and necessary
incidentals to remove and dispose of accumulated sediment down to the original ground line (0% filled).
This item also includes the removal of any material deposited in sump holes.
I. Stone Filter Rings
Maintenance of stone filter rings consists of all labor, tools, materials, equipment, and necessary
incidentals to remove and dispose of accumulated sediment down to the original ground line (0% filled).
This item also includes the removal of any material deposited in sump holes.
165.2 Measurement
Section 165 – Maintenance of Temporary Erosion and Sedimentation Control Devices
Page 12
A. Temporary Silt Fence:
Maintenance of temporary silt fence, Type A, B, or C, is the actual linear feet (meter) of silt fence,
measured in place, where sediment is removed.
B. Check Dams (All Types):
Maintenance of temporary erosion control check dams as specified on the Plans as each of baled straw,
silt fence or rip rap, measured in place, where sediment is removed.
C. Silt Retention Barrier:
Maintenance of temporary silt retention barrier as specified on the Plans, is measured by the linear foot
(meter) where sediment is removed.
D. Omitted
E. Omitted
F. Construction Exit:
Maintenance of construction exit at the location specified on the Plans, or as directed by the Engineer is
measured per each.
G. Inlet Sediment Trap
Maintenance of inlet sediment trap at the location specified on the Plans, or as added by the Engineer is
measured per each.
H. Rock Filter Dams
Maintenance of rock filter dams as specified on the plans is measured as a single unit.
J. Omitted.
K. Stone Filter Rings
Maintenance of stone filter rings as specified on the plans is measured as a single unit.
165.5 Payment
1. Temporary Silt Fence:
Maintenance of temporary silt fence, Type A, B, or C, is paid for at the contract unit price bid per linear
foot (meter).
2. Check Dams (All Types):
Section 165 – Maintenance of Temporary Erosion and Sedimentation Control Devices
Page 13
Maintenance of Check Dams as specified on the Plans is paid for at the contract unit price bid per each.
3. Sediment Barrier (baled straw):
Maintenance of sediment barrier (baled straw) as specified on the Plans is paid for at the contract unit
price bid per each.
4. Construction Exit:
Maintenance of the construction exit at the location specified on the Plans or as added by the Engineer
is paid for at the contract unit price per each.
5. Rock Filter Dams
Maintenance of rock filter dams as specified on the plans is paid for at the contract unit price bid per
each.
6. Stone Filter Rings
Maintenance of stone filter rings as specified on the plans is paid for at the contract unit price bid per
each.
Payment will be made under:
Item No. 165 Maintenance of temporary silt fence Type____ per linear foot
Item No. 165 Maintenance of check dams (all types) per linear foot
Item No. 165 Maintenance of sediment barrier (baled straw) per linear foot
Item No. 165 Maintenance of construction exit per each
Item No. 165 Maintenance of inlet sediment trap per each
Item No. 165 Maintenance of rock filter dam per each
Item No. 165 Maintenance of stone filter ring per each
Page 14
Section 167—Water Quality Monitoring
167.1 General Description
This Specification establishes the Contractor’s responsibility to meet the requirements of the National
Pollutant Discharge Elimination System (NPDES) Infrastructure Permit No. GAR 100002 as it pertains to
Part IV. Erosion, Sedimentation and Pollution Control Plan.
167.1.01 Definitions
Certified Personnel— certified personnel are defined as persons who have successfully completed the
appropriate certification course approved by the Georgia Soil and Water Conservation Commission.
167.1.02 Related References
A. Referenced Documents
NPDES Infrastructure Permit No. GAR 100002
Environmental Protection Divisions Rules and Regulations (Chapter 391‐3‐26)
Georgia Soil and Water Conservation Commission Certification Level IA course. OCGA 12‐7
167.2 Personnel
Use certified personnel to perform all monitoring, sampling, inspections, and rainfall data collection.
Use the Contractor designated WECS or select a prequalified consultant from the Qualified Consultant
List (QCL) to perform water quality monitoring.
Ensure that monitoring consultants’ employees who perform monitoring, sampling, inspections, and
rainfall data collection are GASWCC Certified.
167.3 Construction
A. General
Perform inspections, rainfall data collection, testing of samples, and reporting the test results on the
project according to the requirements in Part IV of the NPDES Infrastructure permit and this
Specification.
Take samples manually or with the use of automatic samplers, according to the permit. Analyze all
according to the permit, regardless of the method used to collect the samples.
If samples are analyzed in the field using portable turbidemeters, the monitoring results shall state that
they are being used and a digital readout of NTUs is what is provided.
Submit bench sheets, work sheets, etc., when using portable turbidemeters. There are no exceptions to
this requirement.
Section 167 — Water Quality Monitoring
Page 15
Perform required inspections and submit all reports required by this Specification within the time
frames specified. Failure to perform the inspections within the time specified will result in the cessation
of all construction activities with the exception of traffic control and erosion control. Failure to submit
the required reports within the times specified will result in non‐refundable deductions as specified in
Subsection 161.5.01.B.
B. Inspections
Inspection forms may change during the contract to reflect regulatory agency needs or the need of
Macon‐Bibb County. Any costs associated with the change of inspection forms shall be considered
incidental.
The Engineer shall inspect the installation and condition of each erosion control device required by the
erosion control plan within seven days after initial installation. This inspection is performed for each
stage of construction when new devices are installed. The WECS shall ensure all installation deficiencies
reported by the Engineer are corrected within two business days.
Ensure that the inspections of the areas listed below are conducted by certified personnel and at the
frequencies listed.
Document all inspections on appropriate forms.
1. Daily:
a. Petroleum product storage, usage and handling areas
b. All locations where vehicles enter/exit the site
Continue these inspections until all entry and exit sites are stabilized and fuel is not stored or
transferred on the site. Utilize the Daily inspection form.
2. Weekly and after Rainfall Events:
Conduct inspections on these areas every seven calendar days and within twenty‐four hours after the
end of a rainfall event that is 0.5 in (13 mm) or greater:
a. Disturbed areas not permanently stabilized
b. Material storage areas
c. Structural control measures, Best Management Practices (BMPs)
d. Water quality monitoring locations and equipment
Continue these inspections until all BMPs have been removed. Utilize the EC‐1 Form.
3. Monthly:
Once per month, inspect all areas where final stabilization has been completed. Look for evidence of
sediments or pollutants entering the drainage system and or receiving waters. Inspect all permanent
erosion control devices that remain in place to verify the maintenance status and that the devices are
functioning properly.
Section 167 — Water Quality Monitoring
Page 16
Continue these inspections until the Notice of Termination is submitted. Utilize the Monthly inspection
form.
C. Reports:
1. Inspection Reports:
Summarize the results of inspections noted above in writing on the appropriate Daily, Weekly, Monthly
or form. Include the following information:
Date(s) of inspection
Name of personnel performing inspection
Status of devices
Observations
Action taken
Signature of personnel performing the inspection
Any incidents of non‐compliance
The inspection form certification sheet shall be signed by the project WECS and the inspector
performing inspections on behalf of the WECS (if not the same person).
Submit all inspection reports to the Engineer within twenty‐four hours of the inspection.
The Engineer will review the submitted reports and inspect the project to determine their accuracy.
The Engineer will notify the certified personnel of any additional items that should be added to the
inspection report. Correct any items listed in the inspection report requiring routine maintenance within
72 (seventy –two) hours of notification.
Assume responsibility for all costs associated with additional sampling as specified in Part IV.D.6.d.3.(c)
of the NPDES GAR 100002 permit if either of these conditions arise:
BMPs shown in the Plans are not properly installed and maintained, or
BMPs designed by the Contractor are not properly designed, installed and maintained.
2. Monitoring Reports
a. Report Requirements
Include in all reports, the following certification statement, signed by the WECS or consultant providing
monitoring on the project:
“I certify under penalty of law that this document and all attachments were prepared under my direct
supervision in accordance with a system designed to assure that certified personnel properly gather and
evaluate the information submitted. Based on my inquiry of the person or persons who manage the
system, or those persons directly responsible for gathering the information, the information is, to the
Section 167 — Water Quality Monitoring
Page 17
best of my knowledge and belief, true, accurate and complete. I am aware that there are significant
penalties for submitting false information, including the possibility of fine and imprisonment for
knowing violations.”
b. When a rainfall event requires a sample to be taken, submit a report of the monitoring
results to the Engineer within seven working days of the date the sample was obtained.
Include the following information:
1.) Date of sampling
2.) Rainfall amount on sample date (sample date only)
3.) NTU of sample & analysis method
4.) Location where sample was taken (station number, etc.)
5.) Receiving water or outfall sample
6.) Project number and county
7.) Whether the sample was taken by automatic sampler or manually (grab sample)
c. Report Requirements with No Qualifying Rainfall Events
In the event that a qualifying rainfall event does not occur prior to the submittal of the NOT (Notice of
Termination), submit a report that states “No qualifying rainfall event occurred and no samples were
taken.” d. Test Results
Provide monitoring test results to the Engineer within 48 hours of the samples being analyzed. This
notification may be verbal or written. This notification does not replace the requirement to submit the
formal monitoring summary to the Engineer within 7 working days of the samples being collected.
3. Rainfall Data Reports
Record the measurement of rainfall once each twenty‐four hour period. Measure rainfall data at the
active phase of construction on the site.
Project rain gauges and those used to trigger the automatic samplers are to be emptied after every
rainfall event. This will prevent a cumulative effect and prevent automatic samplers from taking samples
even though the rainfall event was not a qualifying event.
The daily rainfall data supplied by the WECS to the Engineer will be the official rainfall data for the
project. 167.3.06 Quality Acceptance
167.4 Measurement
Water Quality Inspections in accordance with the inspection and reports sub‐sections will be measured
for payment by the month up to the time the Contract Time expires. Required inspections and reports
after Contract Time has expired will not be measured for payment.
Section 167 — Water Quality Monitoring
Page 18
Water Quality Monitoring and Sampling are measured per each. When the monitoring location is
receiving water, the upstream and downstream samples constitute one sample. When the monitoring
location is an outfall, a single outfall sample constitutes one sample.
167.5 Payment
Payment for Water Quality Monitoring and Sampling will be made as follows:
Water Quality Monitoring and Sampling per each is full compensation for meeting the requirements of
the monitoring sections of the NPDES permit and this Specification, obtaining samples, analyzing
samples, any and all necessary incidentals, and providing results of turbidity tests to the Engineer, within
the time frame required by the NPDES Infrastructure permit, and this Specification.
This item is based on the rainfall events that require sampling as described in Part IV.D.5 of the permit.
Macon‐Bibb County will not pay for samples taken and analyzed for rainfall events that are not
qualifying events as compared to the daily rainfall data supplied by the WECS.
Water Quality Inspections will be paid at the Contract Price per month. This is full compensation for
performing the requirements of the inspection section of the NPDES permit and this Specification, any
and all necessary incidentals, and providing results of inspections to the Engineer, within the time frame
required by the NPDES Infrastructure permit, and this Specification.
Payment will be made under:
Item No. 167 Water quality inspections Per month
Water Quality Monitoring and Sampling will be paid per each.
Payment will be made under:
Item No. 167 Water quality monitoring and sampling Per each
Page 19
Section 171—Silt Fence
171.1 General Description
This work includes furnishing, installing, and removing a water permeable filter fabric fence to remove
suspended particles from drainage water.
171.2 Materials
For Type A, B, and C fences, use fabric as specified in Subsection 881.2.07, “Silt Fence Filter Fabric.”
171.2.01 Delivery, Storage, and Handling
During shipment and storage, wrap the fabric in a heavy‐duty covering that will protect the cloth from
sunlight, mud, dust, dirt, and debris. Do not expose the fabric to temperatures greater than 140 °F (60
°C).
When installed, the Engineer will reject the fabric if it has defects, rips, holes, flaws, deterioration, or
damage incurred during manufacture, transportation, or storage.
171.3 Construction
Install the silt fence according to this Specification, as shown on the Plans, or as directed by the
Engineer.
A. Install Silt Fence
1. Install silt fence by either of the following methods:
a. Excavated Trench Method
Excavate a trench 4 to 6 in (100 to 150 mm) deep using equipment such as a trenching machine or
motor grader. If equipment cannot be operated on the site, excavate the trench by hand.
b. Soil Slicing Method
Create a mechanical slice in the soil 8 to 12 in deep to receive the silt fence. Ensure that the width of the
slice is not more than 3 in. Mechanically insert the silt fence fabric into the slice in a simultaneous
operation with the slicing that ensures consistent depth and placement.
2. Install the first post at the center of the low point (if applicable). Space the remaining
posts a maximum of 6 ft apart for Types A and B fence and 4 ft (1.2 m) apart for Type C fence.
3. Bury the posts at least 18 in (450 mm) into the ground. If this depth cannot be attained,
secure the posts enough to prevent the fence from overturning from sediment loading.
4. Attach the filter fabric to the post using wire, cord, staples, nails, pockets, or other
acceptable means.
a. Staples and Nails (Wood Posts): Evenly space staples or nails with at least five per post
for Type A fence and four per post for Type B fence.
Section 171 – Silt Fence
Page 20
b. Pockets: If using pockets, and they are not closed at the top, attach the fabric to a wood
post using at least one additional staple or nail, or to a steel post using wire.
Ensure that the additional attachment is within the top 6 in of the fabric.
c. Install the filter fabric so that 6 to 8 in of fabric is left at the bottom to be buried.
Provide a minimum overlap of 18 in at all splice joints.
d. For Type C fences, attach the filter fabric to the top of a woven wire support fence at
the midpoint between posts.
5. Install the fabric in the trench so that 4 to 6 in of fabric is against the side of the trench
with 2 to 4 in of fabric across the bottom in the upstream direction.
6. Backfill and compact the trench to ensure that flow cannot pass under the barrier.
When the slice method is used, compact the soil disturbed by the slice on the upstream side of
the silt fence first, and then compact the downstream side.
B. Remove the Silt Fence
1. Keep the silt fence in place unless the Engineer directs. A removed silt fence may be
used at other locations if the Engineer approves of its condition.
2. After removing the silt fence, return the area to a pleasing appearance. Seed and mulch
the area according to Section 700.
3. When installing a silt fence across a waterway that produces significant runoff, place a
settling basin in front of the fence to handle the sediment load, if required. Construct a suitable
sump hole or storage area according to Section 163.
171.3.06 Quality Acceptance
Approved silt fence is listed in QPL 36. Approved fabrics must consistently exceed the minimum
requirements of this Specification.
At the time of installation, the Engineer will reject the fabric if it has defects, rips, holes, flaws,
deterioration, or damage incurred during manufacture, transportation, or storage.
171.3.07 Contractor Warranty and Maintenance
Maintain the silt fence until the Project is accepted or until the fence is removed. Also, remove and
dispose of the silt accumulations at the silt fence.
Remove and replace any deteriorated filter fabric that reduces the effectiveness of the silt fence.
Repair or replace any undermined silt fence at no additional cost to Macon‐Bibb County.
171.4 Measurement
The quantity of silt fence to be paid for is the actual number of linear feet (meters) of silt fence,
measured in place from end post to end post of each separate installation. The silt fence must be
complete and accepted.
Section 171 – Silt Fence
Page 21
171.5 Payment
Silt fence Type A, B, or C measured as defined in Subsection 171.4, “Measurement,” is paid for at the
Contract Unit Price bid per linear foot (meter).
Payment is full compensation for the following:
Furnishing materials
Erecting and maintaining the fence
Removing accumulated silt
Dressing and grassing, when required
Removing the fence, when required Payment for this Item is made as follows:
Seventy‐five percent of the Contract Price bid per linear foot (meter) is paid when each
fence is complete in place.
Twenty‐five percent is paid at removal or acceptance.
If the silt fence must be repaired or removed, perform the work at no additional cost to Macon‐Bibb
County.
Payment will be made under:
Item No. 171 Silt fence, type A Per linear foot
Item No. 171 Silt fence, type C Per linear foot
Page 22
Section 210—Grading Complete
1. SCOPE
This work includes:
Excavating of all materials including ditches, undesirable material (including removal and
replacement), and borrow (if required)
Hauling
Forming embankments
Constructing shoulders and subgrades
Finishing, dressing, and disposing of undesirable or surplus material
Clearing and grubbing unless these items are established as Pay Items in the Contract
Removing and disposing of miscellaneous roadway items, including but not limited to curbs,
drainage structures, and pavements (unless established as separate contract items)
Ensure that the completed grading work conforms to the horizontal and vertical alignment and
typical cross‐ sections shown on the Plans or as directed by the Engineer.
2. GENERAL
The Contractor shall accept the site in its existing condition, and shall assume the risk of
encountering whatever materials as may occur. Refer to and comply with Soils Report.
3. DEWATERING AND PROTECTION AGAINST WATER
The Contractor shall remove water from the site and shall lower the ground water level as necessary to
complete the excavations to the required depths and as required to maintain the excavations
sufficiently dry so that all required work can be accomplished. The
Contractor shall do such well construction, well pointing, sheeting, ditching, diking and pumping and
shall construct necessary drains, channels, sumps and cofferdams to keep his excavations
and new structures clear of ground water, storm water or sewage and to keep his construction areas
dry during the progress of the work and until the finished work is accepted by the Owner, except as
otherwise specified.
The Contractor shall be responsible for the effect of dewatering operations on adjacent property and
for the effect on water supplies located in the vicinity of the project.
Adequate measures and protection shall be provided by the Contractor to protect his work
from damage from uplift due to ground water, storm water, or flood water.
Any damages which may result shall be the Contractor's responsibility.
The Contractor shall accept all responsibility for damage to the work of this Contract because of floods
and water pressures and other water damages and shall accept all risks of floods and other
events which may occur.
Section 210 – Grading Complete
Page 23
All water discharged by pumping operations shall be discharged so as not to interfere with work
under this Contract or with existing structures and operations. Route of dewatering pipe shall be
subject to the Engineer's review. Discharge facilities and water quality shall comply
with applicable regulations of State and Federal agencies.
Dewatering operations shall be uninterrupted and continuous during the course of the work so as not to
endanger any construction in place or to present a hazard to workmen in and around the site. The
Contractor shall take all measures necessary including, but not limited to, standby equipment and
constant attendance to insure that the dewatering system remains operational and
effective throughout the period of time that it is required.
4. MATERIALS
A. Earth Fill.
Earth fill, including pavement subgrades, shall consist of all suitable materials from required
excavations. Suitable materials for earth fill shall generally be composed of sands, clay‐sand
mixtures and silt‐sand mixtures. Clay‐sand and silt‐sand mixtures shall be approved by the soil
technician prior to being incorporated in fills. Highly plastic clays and silts, and organic soils will be
considered as unsuitable materials.
B. Excavated Materials.
All suitable materials from excavations shall be used in the permanent construction required under
these Specifications. Suitable materials shall be excavated separately from materials to be wasted and
the suitable materials shall be segregated by loads during
the excavation operations and shall be placed in temporary stockpiles and later placed in
the designated locations. Excavated materials, which, after drainage, are suitable for the embankment
but which, when excavated are too wet for immediate compaction in the embankment,
shall be placed temporarily in stockpiles until the moisture content is reduced sufficiently to
permit them to be placed in the earth fills.
C. Excess Materials.
All excess material from required excavations shall be removed from the site unless written
authorization is given by the Engineer to stockpile the material on the site.
5. EXCAVATION
Excavation shall include the loosening, loading, removing, transporting, stockpiling and disposing of all
materials, wet or dry, necessary to be removed to construct all structures included in this Contract to the
lines and grades, and at the locations, shown on the Contract Drawings. Excavation for outside piping,
storm sewers and utilities systems is included in other Sections of these Specifications.
Excavation for structures shall conform to the depth and dimensions necessary for the
proper installation of all structures detailed on the Contract Drawings. Unless shown on the Drawings
excavation shall not be carried below the elevations shown on the Drawings. Where bottoms of
excavations are slightly unstable and the Drawings do not require a stabilized granular backfill
Section 210 – Grading Complete
Page 24
and the Engineer does not direct additional excavation and replacement, the Contractor may provide
a gravel course, but such work will be considered as for the Contractor's convenience and will not
be considered as extra work..
Where any unauthorized excavation is made below the elevation indicated on the
Contract Drawings, the excavation shall be restored to the proper elevation with compacted, well graded
granular backfill. Such backfill shall be compacted as specified in the Article entitled "Compaction".
Excavation for pipes under and adjacent to structures shall be made after the installation of the
granular backfill. Excavations shall be made to the required depths, grades, alignment, and trench
widths required for the installation of the pipe. Temporary sheeting and bracing shall be used as
required to confine the trench size and width. Trench size and width shall conform to the requirements
in Section 02221.
Excavation shall be made for roadways and other site work to the required depths, grades and
alignment.
Excavations, where conditions require, shall be properly shored, sheeted and braced by the Contractor
to maintain excavation in a condition to permit the safe and efficient installation of all items
of Contract work. Upon completion of the various Contract items, all temporary forms, shores and
bracing shall be removed. While being withdrawn, all voids left by the sheeting and
bracing shall be carefully filled with sand and compacted.
6. TOPSOIL CONSERVATION
Over areas requiring excavation and/or fill, there may be limited amounts of existing topsoil, suitable
for future use. The Contractor shall strip all such topsoil and shall stockpile it for future use under
this Contract. Except for topsoil material available from the excavation, topsoil shall be obtained from
off‐site borrow.
7. UNSUITABLE MATERIAL
Where material encountered is unsuitable for subgrade construction of roads, paved areas, buildings
and walks, such material shall be excavated to the required depth of
compaction (generally two feet below pavement base course), disposed of off the site and property
of the Owner and replaced with suitable material. Unsuitable materials are those classified as
MH, CH, OH, OL, and Peat in accordance with the Unified Soil Classification System. Excess water in
material will not be a basis for establishing unsuitable material regardless of
gradation. The Engineer shall be notified immediately upon encountering of unsuitable material.
8. BORROW
It is anticipated that suitable material for required fill and backfill can be obtained from required
excavation. Suitable materials shall be secured by the Contractor from off‐site sources if required.
9. BACKFILLING
All excavation shall be backfilled to the lines and grades shown on the Contract Drawings. Backfill adjacent
to structures shall not be placed until forms, form lumber and all debris from construction has been
Section 210 – Grading Complete
Page 25
entirely removed from around the work. No backfilling shall be done in unsuitable weather or over
ground that is frozen or too wet.
Backfill shall not be placed against structures until the concrete has cured at least 7 days. Backfill, in
general, shall be placed in horizontal layers not in excess of 12 inches in thickness, except in
the cases of embankment construction around structures and under roadway and piping locations,
where backfill shall be placed in 6 inch layers, with each layer thoroughly compacted as
specified hereinafter , prior to the addition of the succeeding layer.
Fill material shall be suitable material taken from the excavation. All sticks, debris, organic matter,
frozen material, stones or cobbles over 6 inches in maximum dimension, and other deleterious
material shall be removed from the backfill material prior to its use.
10. COMPACTION
A. General.
Compaction of earth fill and all pavement subgrades shall be performed to the percentages of maximum
standard or modified dry densities and to the depths as shown on the drawing or as follows:
Subgrades Under Paved Areas and Structures.
98 Percent Standard (ASTM Test D698) 24 lnches
95 Percent Standard (ASTM Test D698) Below 24 Inches
Pedestrian Traffic Subgrades.
95 Percent Standard (ASTM Test D698) Full Depth
Unpaved Areas To Be Grassed Or Sodded.
95 Percent Standard (ASTM Test D698) Full Depth
B. Moisture Content.
All compaction shall be performed at material moisture contents within 3 percentage points, plus or minus
of optimum. Compaction and proof rolling equipment shall be as outlined in Section 02500 or as may be
required for the type of fill being compacted.
11. TESTING
A. General.
The Contractor will select a qualified independent testing laboratory for the purpose of identifying soils,
checking densities, and classifying soils materials during construction. Payment for the testing will be by
the Contractor and will be included in the cost of work done under the specifications.
One compaction test per 500 cubic yards of fill and 1,500 square yards of base, and one "proctor" test
shall be conducted for each type of fill material to determine if the proper compaction has been attained.
B. Moisture‐Density Tests.
Section 210 – Grading Complete
Page 26
Testing shall be in accordance with ASTM Methods D698 and D1557. A test shall be performed on each
type of material used in the work regardless of source. Tests will be accompanied by particle‐size analyses
of the soils tested (ASTM Methods D421 and D422). Changes in color, gradation, plasticity or source of
fill material will require the performance of additional tests. Copies of all test results shall be furnished
to the Engineer.
C. Field Density Tests.
Tests shall be made in accordance with ASTM method D1556. If the mica content of the fill soils is low,
ASTM D2922 may be used at the discretion of the soil technician. If any compaction test reveals that fill
or backfill is not compacted as specified, the Contractor shall scarify and recompact as required to achieve
the specified density. Additional compaction tests shall be made to verify proper compaction. These
additional tests, required due to failure of the original test, shall be paid for by the Contractor and not be
reimbursed by the Owner.
D. Submittals.
The soils technicians will submit formal reports of all compaction tests and retests to
the Contractor and Engineer as soon as possible upon completion of the required tests. This report
information is to include but not be limited to the following:
1. Date of the test and date submitted.
2. Location of test.
3. Wet weight, moisture content and dry weight of field sample.
4. Description of soil.
5. Maximum dry density and moisture content of the lab sample which best matches the field sample in
color, texture, grain size and maximum dry density.
6. Ratio of field dry density to maximum lab dry density expressed as a percentage.
7. Comments concerning the field density passing or failing the specified compaction. Comments about
re‐compaction if required.
E. Compaction Results.
The soils technician is to advise the Engineer and Contractor immediately of any compaction tests failing
to meet the specified minimum requirements. No additional lift is to be placed on a lift with any portion
failing.
12. GRADING
Upon completion of other construction operations, the entire site, within the limits shown on the
Drawings, shall be brought to the finished grades shown. All surfaces shall be sloped to the grades
indicated and which will provide proper drainage. All surfaces shall be raked smooth and shall be free of
all vegetable matter, debris and stones larger than 2‐1/2 inches. Allow for thickness of required topsoil.
Section 210 – Grading Complete
Page 27
13. Quality Acceptance
When the Engineer determines that the existing material in areas where fills are to be placed is
undesirable, the Engineer may require the Contractor to remove the undesirable material and replace it
with suitable material.
Compact the replacement materials according to the applicable portions of Section 208.
In cut areas, where the material below the template line is undesirable for subgrade or
shoulders, undercut it to a depth established by the Engineer and replace it with suitable
material.
Compact the replacement materials as specified herein.
14. Payment
A. Grading Complete
This Item completed and accepted will be paid for at the Lump Sum Price bid. Payment is full
compensation for all work and materials specified in this Section.
B. Undercut Excavation
Undercutting areas not shown in the Plans when directed by the Engineer will be paid for at the rate of
$5.00 per cubic yard.
Payment will be made under:
Item No. 210 Grading complete Per lump sum
Page 28
Section 310—Graded Aggregate and Concrete Base Construction
310.1 General Description
This work includes constructing a base, subbase or shoulder course composed of mineral aggregates.
Construct according to these Specifications and to the lines, grades, thickness, and typical cross‐sections
shown on the Plans or established by the Engineer.
A. Placing Material – Graded Aggregate
Use the following steps to mix base and spread subbase or shoulder course.
1. Mixing
When blending two sizes of aggregate, proportion the aggregate and water, if needed, into the central
plant. Mix until producing a homogeneous and uniform mixture.
2. Spreading
To obtain the specified thickness, uniformly spread materials to the proper depth with a mixture
spreader. Do not use materials containing frost or frozen particles. a. One‐Course Construction
Lay one course to a maximum thickness of 8 in (200 mm) compacted.
b. Multiple‐Course Construction
If the thickness of the base, subbase or shoulder course exceeds 8 in (200 mm), construct it in 2 or more
courses of equal thickness.
B. Compacting Material
Use the following steps to compact and finish a base, subbase, or shoulder course.
1. Moisture Content
Ensure that the moisture content of materials is uniformly distributed and allows compaction to the
specified density.
Unless approved by the Engineer, no graded aggregate will be shipped to a project when the moisture
content of the material exceeds two percent of optimum moisture.
2. Compaction
After shaping the spread material to line, grade, and cross‐section, roll to uniformly compact the course.
If using Group 1 aggregate, roll to at least 98 percent of maximum dry density. If using Group 2
aggregate, roll to at least 100 percent of the maximum dry density.
If using graded aggregate mixtures composed of either group as base for paved shoulders 6 ft (1.8 m)
wide or less, compact to at least 96 percent of the maximum dry density.
Section 310 – Graded Aggregate Construction
Page 29
Regardless of compaction, ensure that the compacted base is sufficiently stable to support construction
equipment without pumping. If the base material is unstable from too much moisture, dry and rework
the base material. Dry and rework the underlying subgrade, if necessary.
a. One‐Course Construction
1) After compaction, shape to the required grade, line, and cross‐ section.
2) Add water as necessary to develop the proper moisture content.
3) Roll until the surface is smooth, closely knit, and free of cracks.
4) Correct all defects.
b. Multiple‐Course Construction
1) After compacting the first course, shape the surface again to line, grade, and cross
section.
2) Add water as necessary to develop the proper moisture content.
3) Spread and compact the second and any succeeding courses without rolling the first
course again.
4) Finish the surface according to the procedure specified for one‐course construction. c.
Irregular Areas
In places inaccessible to the roller, obtain the required compaction with mechanical tampers.
C. Finishing
Finish immediately after the placing and compacting operations.
E. Priming the Base
Apply bituminous prime unless using:
Graded aggregate base under Portland cement concrete pavement
Graded aggregate base under asphaltic concrete 5 in or more in total thickness
310.3.06 Quality Acceptance
A. Compaction Tests
1. Determine the maximum dry density from representative samples of compacted
material, according to AASHTO T180, Method D.
2. Determine the in‐place density of finished courses according to GDT 21 or GDT 59 ,
where applicable.
B. Finished Surface
Check the finished surface of the base, subbase, or shoulder course as follows:
Section 310 – Graded Aggregate Construction
Page 30
1. Check the longitudinal surface using a 15 ft (4.5 m) straightedge parallel to the
centerline.
2. Check the transverse surface by using one of the following tools:
A template, cut true to the required cross‐section and set with a spirit level on
non‐superelevated sections
A system of ordinates, measured from a stringline
A surveyor’s level
3. Ensure that ordinates measured from the bottom of the template, stringline, or
straightedge, to the surface do not exceed 1/4 in (6 mm) at any point. Rod readings shall not
deviate more than 0.02 ft (6 mm) from required readings.
C. Thickness Tolerances
1. Thickness Measurements
a. Thickness requirements apply to shoulder construction where the Plans specify a
uniform thickness, or where the shoulders will be surfaced.
b. Determine the thickness of the base, subbase, or shoulder course, by making as many
checks as necessary to determine the average thickness.
2. Deficient Thickness
a. If any measurement is deficient in thickness more than 1/2 in (13 mm), make additional
measurements to determine the deficient area.
b. Correct any area deficient between 1/2 in (13 mm) and 1 in (25 mm) to the design
thickness by using one of the following methods according to these Specifications:
Add additional quantities of the same materials and reconstruct to the required thickness
Leave in place and accept payment for the materials and area at ½ the Contract Unit Price for the
deficient area.
c. Correct any area deficient in thickness by more than 1 inch (25 mm) by adding
additional quantities of the same material and reconstructing to the required thickness in
accordance with these Specifications.
d. If payment is made by the ton (megagram), payment for additional material to correct
deficiencies will be made at the Contract Unit Price with no additional cost to the
Department for scarification, mixing or compaction.
e. If payment is made by the square yard (meter), no payment will be made for additional
material required to correct deficiencies or for reconstructing deficient work.
3. Average Thickness
Section 310 – Graded Aggregate Construction
Page 31
a. The average thickness per linear mile (kilometer) is determined from all measurements
within the mile (kilometer) increments except the areas deficient by more than 1/2 in (13
mm) and not corrected.
b. The average thickness shall not exceed the specified thickness by more than 1/2 in (13
mm).
c. If the basis of payment is per ton (megagram), and the average thickness for any mile
(kilometer) increment exceeds the allowable 1/2 in (13 mm) tolerance, the excess quantity
in that increment will be deducted from the Contractor’s payments.
d. The excess quantity is calculated by multiplying the average thickness that exceeds the
allowable 1/2 in (13 mm) tolerance by the surface area of the base, subbase, or shoulder.
e. If the basis of payment is per square yard (meter), no deduction will be made for excess
thickness.
310.4 Measurement
A. Graded Aggregate
Where specified for payment by the ton, graded aggregate base, subbase or shoulder materials are
measured in tons, mixed and accepted. When hauling material to the roadway, the actual weight of
each loaded vehicle is determined with an approved motor truck scale.
Where specified for payment by the square yard (meter) for a certain thickness, the surface length is
measured along the centerline, and the width is specified on the Plans. Measure irregular areas, such as
turnouts and intersections, by the square yard (meter).
B. Bituminous Prime
Bituminous prime is not measured for separate payment.
310.5 Payment
A. Graded Aggregate
Graded aggregate base, subbase, or shoulder course will be paid for at the Contract Unit Price per
square yard, complete, in place, and accepted. This payment shall be full compensation for:
Materials
Shaping and compacting the existing roadbed
Loading, hauling, and unloading
Crushing and processing
Mixing
Spreading
Watering
Compacting and shaping
Maintenance
Priming, when required
Section 310 – Graded Aggregate Construction
Page 32
All incidentals necessary to complete The Work
Payment will be made under:
Item No.
310
Graded aggregate (base, subbase, shoulder course)—including
material Per square yard
When using narrow sections of Portland cement concrete to widen existing bases or bases and
pavements, use Class B concrete as shown on the Plans or as directed by the Engineer.
Class B concrete used for base and pavement widening will be measured and paid for by the cubic
yard (meter) complete in place and accepted.
500 Class B concrete base or pavement widening Per cubic yard
Page 33
Section 321216 – Asphalt Paving
PART 1 ‐ GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes: 1. Hot‐mix asphalt patching. 2. Hot‐mix asphalt paving. 3. Hot‐mix asphalt overlay.
B. Related Requirements: 1. Section 312000 "Earth Moving" for subgrade preparation, fill material, unbound‐
aggregate subbase and base courses, and aggregate pavement shoulders. 2. Section 321373 "Concrete Paving Joint Sealants" for joint sealants and fillers at pavement
terminations.
1.3 ACTION SUBMITTALS
A. Product Data: For each type of product.
1. Include technical data and tested physical and performance properties. 2. Job‐Mix Designs: Certification, by authorities having jurisdiction, of approval of each job
mix proposed for the Work. 3. Job‐Mix Designs: For each job mix proposed for the Work.
1.4 INFORMATIONAL SUBMITTALS
A. Material Certificates: For each paving material.
B. Material Test Reports: For each paving material, by a qualified testing agency.
C. Field quality‐control reports.
Section 312216 – Asphalt Paving
Page 34
1.5 QUALITY ASSURANCE
A. Manufacturer Qualifications: A paving‐mix manufacturer registered with and approved by GDOT.
B. Testing Agency Qualifications: Qualified according to ASTM D 3666 for testing indicated.
C. Regulatory Requirements: Comply with materials, workmanship, and other applicable requirements of Georgia DOT for asphalt paving work.
1. Measurement and payment provisions and safety program submittals included in standard specifications do not apply to this Section.
1.6 FIELD CONDITIONS
A. Environmental Limitations: Do not apply asphalt materials if subgrade is wet or excessively damp, if rain is imminent or expected before time required for adequate cure, or if the following conditions are not met:
1. Prime Coat: Minimum surface temperature of 60 deg F (15.6 deg C). 2. Tack Coat: Minimum surface temperature of 60 deg F (15.6 deg C). 3. Slurry Coat: Comply with weather limitations in ASTM D 3910. 4. Asphalt Base Course: Minimum surface temperature of 40 deg F (4.4 deg C) and rising at
time of placement. 5. Asphalt Surface Course: Minimum surface temperature of 60 deg F (15.6 deg C) at time
of placement.
PART 2 ‐ PRODUCTS
2.1 AGGREGATES
A. General: Use materials and gradations that have performed satisfactorily in previous installations.
B. Coarse Aggregate: ASTM D 692/D 692M, sound; angular crushed stone, crushed gravel, or cured, crushed blast‐furnace slag.
C. Fine Aggregate: AASHTO M 29, sharp‐edged natural sand or sand prepared from stone, gravel, cured blast‐furnace slag, or combinations thereof.
1. For hot‐mix asphalt, limit natural sand to a maximum of 20 percent by weight of the total aggregate mass.
D. Mineral Filler: AASHTO M 17, rock or slag dust, hydraulic cement, or other inert material.
Section 312216 – Asphalt Paving
Page 35
2.2 ASPHALT MATERIALS
A. Asphalt Binder: AASHTO M 320, PG 64‐22 or PG 67‐22 d.
B. Asphalt Cement: ASTM D 3381/D 3381M for viscosity‐graded material ASTM D 946/D 946M for penetration‐graded material.
C. Cutback Prime Coat: ASTM D 2027, medium‐curing cutback asphalt, MC‐30, MC‐70, MC‐250.
D. Emulsified Asphalt Prime Coat: AASHTO M 140 emulsified asphalt, or AASHTO M 208 cationic emulsified asphalt, slow setting, diluted in water, of suitable grade and consistency for application.
E. Tack Coat: AASHTO M 140emulsified asphalt, or AASHTO M 208 cationic emulsified asphalt, slow setting, diluted in water, of suitable grade and consistency for application.
F. Fog Seal: AASHTO M 140 emulsified asphalt, or AASHTO M 208 cationic emulsified asphalt, slow setting, factory diluted in water, of suitable grade and consistency for application.
G. Water: Potable.
H. Undersealing Asphalt: ASTM D 3141/D 3141M; pumping consistency.
2.3 AUXILIARY MATERIALS
A. Recycled Materials for Hot‐Mix Asphalt Mixes: Reclaimed asphalt pavement; reclaimed, unbound‐aggregate base material; and recycled [tires] [asphalt shingles] [or] [glass] from sources and gradations that have performed satisfactorily in previous installations, equal to performance of required hot‐mix asphalt paving produced from all new materials.
B. Herbicide: Commercial chemical for weed control, registered by the EPA, and not classified as "restricted use" for locations and conditions of application. Provide in granular, liquid, or wettable powder form.
C. Sand: AASHTO M 29, Grade No. 2 or No. 3.
D. Paving Geotextile: AASHTO M 288 paving fabric; nonwoven polypropylene; resistant to chemical attack, rot, and mildew; and specifically designed for paving applications.
E. Joint Sealant: AASHTO M 324], Type II or III, hot‐applied, single‐component, polymer‐modified bituminous sealant.
2.4 MIXES
1. Surface Course Limit: Recycled content no more than 10 percent by weight.
Section 312216 – Asphalt Paving
Page 36
B. Hot‐Mix Asphalt: Dense‐graded, hot‐laid, hot‐mix asphalt plant mixes approved by GDOT; designed according to procedures in AI MS‐2, "Mix Design Methods for Asphalt Concrete and Other Hot‐Mix Types"; and complying with the following requirements:
1. Provide mixes with a history of satisfactory performance in geographical area where Project is located.
2. Base Course: 19 mm “Superpave” hot mix asphalt is to be spread and finished to a mat thickness of 3.0 in.
3. Surface Course: 12.5 mm “Superpave” hot mix asphalt is to be spread and finished to a mat thickness of 1.5 in.
C. Omitted
PART 3 ‐ EXECUTION
3.1 EXAMINATION
A. Verify that subgrade is dry and in suitable condition to begin paving.
B. Proof‐roll subgrade below pavements with heavy pneumatic‐tired equipment to identify soft pockets and areas of excess yielding. Do not proof‐roll wet or saturated subgrades.
1. Completely proof‐roll subgrade in one direction. Limit vehicle speed to 3 mph. 2. Proof roll with a loaded 10‐wheel, tandem‐axle dump truck weighing not less than 15
tons. 3. Excavate soft spots, unsatisfactory soils, and areas of excessive pumping or rutting, as
determined by Architect, and replace with compacted backfill or fill as directed.
C. Proceed with paving only after unsatisfactory conditions have been corrected.
3.2 PATCHING
A. Asphalt Pavement: Saw cut perimeter of patch and excavate existing pavement section to sound base. Excavate rectangular or trapezoidal patches, extending 12 inches into perimeter of adjacent sound pavement, unless otherwise indicated. Cut excavation faces vertically. Remove excavated material. Recompact existing unbound‐aggregate base course to form new subgrade.
B. Portland Cement Concrete Pavement: Break cracked slabs and roll as required to reseat concrete pieces firmly.
1. Pump hot undersealing asphalt under rocking slab until slab is stabilized or, if necessary, crack slab into pieces and roll to reseat pieces firmly.
2. Remove disintegrated or badly cracked pavement. Excavate rectangular or trapezoidal patches, extending into perimeter of adjacent sound pavement, unless otherwise indicated. Cut excavation faces vertically. Recompact existing unbound‐aggregate base course to form new subgrade.
Section 312216 – Asphalt Paving
Page 37
C. Tack Coat: Before placing patch material, apply tack coat uniformly to vertical asphalt surfaces abutting the patch. Apply at a rate of 0.05 to 0.15 gal./sq. yd.
1. Allow tack coat to cure undisturbed before applying hot‐mix asphalt paving. 2. Avoid smearing or staining adjoining surfaces, appurtenances, and surroundings. Remove
spillages and clean affected surfaces.
D. Placing Patch Material: Fill excavated pavement areas with hot‐mix asphalt base mix for full thickness of patch and, while still hot, compact flush with adjacent surface.
E. Placing Patch Material: Partially fill excavated pavements with hot‐mix asphalt base mix and, while still hot, compact. Cover asphalt base course with compacted, hot‐mix surface layer finished flush with adjacent surfaces.
3.3 REPAIRS
A. Leveling Course: Install and compact leveling course consisting of hot‐mix asphalt surface course to level sags and fill depressions deeper than 1 inch in existing pavements.
1. Install leveling wedges in compacted lifts not exceeding 3 inches thick.
B. Crack and Joint Filling: Remove existing joint filler material from cracks or joints to a depth of 1/4 inch.
1. Clean cracks and joints in existing hot‐mix asphalt pavement. 2. Use emulsified‐asphalt slurry to seal cracks and joints less than 1/4 inch wide. Fill flush
with surface of existing pavement and remove excess. 3. Use hot‐applied joint sealant to seal cracks and joints more than 1/4 inch wide. Fill flush
with surface of existing pavement and remove excess.
3.4 SURFACE PREPARATION
A. General: Immediately before placing asphalt materials, remove loose and deleterious material from substrate surfaces. Ensure that prepared subgrade is ready to receive paving.
B. Herbicide Treatment: Apply herbicide according to manufacturer's recommended rates and written application instructions. Apply to dry, prepared subgrade or surface of compacted‐aggregate base before applying paving materials.
1. Mix herbicide with prime coat if formulated by manufacturer for that purpose.
C. Cutback Prime Coat: Apply uniformly over surface of compacted unbound‐aggregate base course at a rate of 0.15 to 0.50 gal./sq. yd. Apply enough material to penetrate and seal, but not flood, surface. Allow prime coat to cure.
Section 312216 – Asphalt Paving
Page 38
1. If prime coat is not entirely absorbed within 24 hours after application, spread sand over surface to blot excess asphalt. Use enough sand to prevent pickup under traffic. Remove loose sand by sweeping before pavement is placed and after volatiles have evaporated.
2. Protect primed substrate from damage until ready to receive paving.
D. Emulsified Asphalt Prime Coat: Apply uniformly over surface of compacted unbound‐aggregate base course at a rate of 0.10 to 0.30 gal./sq. yd. per inch. Apply enough material to penetrate and seal, but not flood, surface. Allow prime coat to cure.
1. If prime coat is not entirely absorbed within 24 hours after application, spread sand over surface to blot excess asphalt. Use enough sand to prevent pickup under traffic. Remove loose sand by sweeping before pavement is placed and after volatiles have evaporated.
2. Protect primed substrate from damage until ready to receive paving.
E. Tack Coat: Apply uniformly to surfaces of existing pavement at a rate of 0.05 to 0.15 gal./sq. yd.
1. Allow tack coat to cure undisturbed before applying hot‐mix asphalt paving. 2. Avoid smearing or staining adjoining surfaces, appurtenances, and surroundings. Remove
spillages and clean affected surfaces.
3.5 PLACING HOT‐MIX ASPHALT
A. Machine place hot‐mix asphalt on prepared surface, spread uniformly, and strike off. Place asphalt mix by hand in areas inaccessible to equipment in a manner that prevents segregation of mix. Place each course to required grade, cross section, and thickness when compacted.
1. Place hot‐mix asphalt base course in number of lifts and thicknesses indicated. 2. Place hot‐mix asphalt surface course in single lift. 3. Spread mix at a minimum temperature of 250 deg F (121 deg C). 4. Begin applying mix along centerline of crown for crowned sections and on high side of
one‐way slopes unless otherwise indicated. 5. Regulate paver machine speed to obtain smooth, continuous surface free of pulls and
tears in asphalt‐paving mat.
B. Place paving in consecutive strips not less than 10 feet wide unless infill edge strips of a lesser width are required.
1. After first strip has been placed and rolled, place succeeding strips and extend rolling to overlap previous strips. Overlap mix placement about 1 to 1‐1/2 inches from strip to strip to ensure proper compaction of mix along longitudinal joints.
2. Complete a section of asphalt base course before placing asphalt surface course.
C. Promptly correct surface irregularities in paving course behind paver. Use suitable hand tools to remove excess material forming high spots. Fill depressions with hot‐mix asphalt to prevent segregation of mix; use suitable hand tools to smooth surface.
Section 312216 – Asphalt Paving
Page 39
3.6 JOINTS
A. Construct joints to ensure a continuous bond between adjoining paving sections. Construct joints free of depressions, with same texture and smoothness as other sections of hot‐mix asphalt course.
1. Clean contact surfaces and apply tack coat to joints. 2. Offset longitudinal joints, in successive courses, a minimum of 6 inches. 3. Offset transverse joints, in successive courses, a minimum of 24 inches. 4. Construct transverse joints at each point where paver ends a day's work and resumes
work at a subsequent time. 5. Compact joints as soon as hot‐mix asphalt will bear roller weight without excessive
displacement. 6. Compact asphalt at joints to a density within 2 percent of specified course density.
3.7 COMPACTION
A. General: Begin compaction as soon as placed hot‐mix paving will bear roller weight without excessive displacement. Compact hot‐mix paving with hot, hand tampers or with vibratory‐plate compactors in areas inaccessible to rollers.
1. Complete compaction before mix temperature cools to 185 deg F (85 deg C).
B. Breakdown Rolling: Complete breakdown or initial rolling immediately after rolling joints and outside edge. Examine surface immediately after breakdown rolling for indicated crown, grade, and smoothness. Correct laydown and rolling operations to comply with requirements.
C. Intermediate Rolling: Begin intermediate rolling immediately after breakdown rolling while hot‐mix asphalt is still hot enough to achieve specified density. Continue rolling until hot‐mix asphalt course has been uniformly compacted to the following density:
1. Average Density: 96 percent of reference laboratory density according to AASHTO T 245, but not less than 94 percent or greater than 100 percent.
2. Average Density: 92 percent of reference maximum theoretical density according to ASTM D 2041, but not less than 90 percent or greater than 96 percent.
D. Finish Rolling: Finish roll paved surfaces to remove roller marks while hot‐mix asphalt is still warm.
E. Edge Shaping: While surface is being compacted and finished, trim edges of pavement to proper alignment. Bevel edges while asphalt is still hot; compact thoroughly.
F. Repairs: Remove paved areas that are defective or contaminated with foreign materials and replace with fresh, hot‐mix asphalt. Compact by rolling to specified density and surface smoothness.
G. Protection: After final rolling, do not permit vehicular traffic on pavement until it has cooled and hardened.
Section 312216 – Asphalt Paving
Page 40
H. Erect barricades to protect paving from traffic until mixture has cooled enough not to become marked.
3.8 INSTALLATION TOLERANCES
A. Pavement Thickness: Compact each course to produce the thickness indicated within the following tolerances:
1. Base Course: Plus or minus 1/2 inch. 2. Surface Course: Plus 1/4 inch, no minus.
B. Pavement Surface Smoothness: Compact each course to produce a surface smoothness within the following tolerances as determined by using a 10‐foot straightedge applied transversely or longitudinally to paved areas:
1. Base Course: 1/4 inch. 2. Surface Course: 1/8 inch. 3. Crowned Surfaces: Test with crowned template centered and at right angle to crown.
Maximum allowable variance from template is 1/4 inch.
3.9 FIELD QUALITY CONTROL
A. Testing Agency: The Contractor will engage a qualified testing agency to perform tests and inspections.
B. Thickness: In‐place compacted thickness of hot‐mix asphalt courses will be determined according to ASTM D 3549.
C. Surface Smoothness: Finished surface of each hot‐mix asphalt course will be tested for compliance with smoothness tolerances.
D. Asphalt Traffic‐Calming Devices: Finished height of traffic‐calming devices above pavement will be measured for compliance with tolerances.
E. In‐Place Density: Testing agency will take samples of uncompacted paving mixtures and compacted pavement according to AASHTO T 168.
1. Reference maximum theoretical density will be determined by averaging results from four samples of hot‐mix asphalt‐paving mixture delivered daily to site, prepared according to ASTM D 2041, and compacted according to job‐mix specifications.
2. In‐place density of compacted pavement will be determined by testing core samples according to ASTM D 1188 or ASTM D 2726.
a. One core sample will be taken for every 1000 sq. yd. or less of installed pavement, with no fewer than three cores taken.
Section 312216 – Asphalt Paving
Page 41
b. Field density of in‐place compacted pavement may also be determined by nuclear method according to ASTM D 2950 and correlated with ASTM D 1188 or ASTM D 2726.
F. Replace and compact hot‐mix asphalt where core tests were taken.
G. Remove and replace or install additional hot‐mix asphalt where test results or measurements indicate that it does not comply with specified requirements.
3.10 WASTE HANDLING
A. General: Handle asphalt‐paving waste according to approved waste management plan required in Section 017419 "Construction Waste Management and Disposal."
4.00 MEASUREMENT
A. Recycled asphaltic concrete mixture, complete in place and accepted, is measured in tons. The weight is determined by recorded weights if an approved recording device is used. Or, the weight is determined by weighing each loaded vehicle on an approved motor truck scale as the material is hauled to the roadway.
4.01 PAYMENT
The work performed and the materials furnished as described in this Specification will be paid for at the Contract Unit Price per ton (megagram). Payment is full compensation for providing materials, hauling and necessary crushing, processing, placing, rolling and finishing the recycled mixture, and providing labor, tools, equipment, and incidentals necessary to complete the work, including hauling and stockpiling RAP or RAS material.
3.11 Payment will be made under:
Item No. 402 Recycled asphaltic concrete 9.5 mm Superpave, group‐2 only, including bituminous materials and hydrated lime
Per ton
Item No. 402 Recycled asphaltic concrete 12.5 mm Superpave, group‐2 only, including bituminous materials and hydrated lime
Per ton
END OF SECTION 321216
Page 42
Section 441—Miscellaneous Concrete
441.1 General Description
This work includes placing Portland cement concrete as follows:
As sidewalks
In concrete curbs, gutters, curb and gutters, and valley gutters
As nonreinforced headwalls
As velocity dissipators and concrete slope drains
Curb cut wheel chair ramps
This work includes subgrade preparations including:
Fine grading and backfilling
Forming, furnishing, placing, and finishing concrete
Constructing weep holes and furnishing and placing the coarse aggregate
Furnishing and placing preformed joint fillers as shown on the Plans
Placing driveway concrete as shown on the Plans. Nominal 4 in or 6 in thick as specified or to match
existing pavement.
441.2 Materials
Use concrete that conforms to the minimum requirements for Class “A” (3000 psi.
Place miscellaneous concrete only when the air temperature is 40 °F (4 °C) and rising. Protect concrete
from freezing for the first 24 hours. Hand finishing is allowed.
441.3 Construction Requirements
441.3.02 Equipment
A. Forms
Forms are subject to the Engineer’s approval. Use forms that are:
Wood or metal that is readily available
Straight and oiled before each use
Use metal divider plates and templates.
Use the slip form placement method when applicable. If the slip form method does not produce a
product with the proper quality, shape, grade, or alignment, the Engineer may require using fixed forms.
B. Weep Holes
Provide weep hole drain pockets filled with coarse aggregate to use with weep hole drain pipe or
formed openings according to the Plan details.
441.3.03 Preparation
Section 441—Miscellaneous Concrete
Page 43
Before placing the concrete, excavate for toe walls, edge walls, and weep hole drain pockets; place
coarse aggregate in weep hole drain pockets; and grade, finish, and compact the subgrade surface. Use
mechanical tamps for compaction if necessary.
441.3.04 Construction
A. Extent and Thickness of Pavement
See the Plans to determine the areas to be paved and the dimensions.
Thicknesses are subject to a minus tolerance of 0.5 in (13 mm). Do not perform overlay pours. B.
Preparation of Subgrade
Finish the subgrade for miscellaneous concrete to the line and grade on the Plans and the following:
1. Compact the subgrade to the same degree as the roadway on which it is placed.
The Contractor shall complete final grading, compacting, dressing, placing, and maintenance to the
structures until completion.
2. When placing paving on the front slopes of ditches and shoulders, place any required
special materials during the roadway construction.
3. When fitting spillways to concrete pavement, set the specified dowel bars into the
pavement when it is laid. Use metal parting strips to hold the ends of dowels bent into the
grooves.
C. Concrete
1. Mixing
Mix Class A concrete as specified in Section 500 with the following exceptions:
a. Use of small capacity job‐site batchers and one‐bag mixers is allowed. The rate of
concrete placement in Subsection 500.3.05.P, “Meet the Minimum Placement Rates” is
waived for miscellaneous concrete.
b. Proportion concrete ingredients volumetrically if the Engineer has approved equipment
calibration and operation and the operator is certified by the Office of Materials and
Research.
2. Placing and Finishing
Place and finish concrete as follows:
a. Deposit concrete within forms or against other pavements on a compacted and wetted
subgrade to the depth to produce the specified thickness.
NOTE: Do not place concrete on a muddy or frozen surface.
b. Vibrate the headwalls.
Section 441—Miscellaneous Concrete
Page 44
c. Strike off the concrete to a plane surface and finish it with a Type IV or Type V finish as
defined in Subsection 500.3.05.AB, “Finish Concrete” and complete the following:
1) Concrete Slope Paving. Give a final finish with a stiff‐bristle broom. With the
Engineer’s approval, mechanically convey the concrete to the forms.
2) Concrete Sidewalks. Give a Type V finish unless otherwise noted on the Plans.
Test the surface with a 10 ft (3 m) straightedge laid parallel to the center line. Eliminate
irregularities greater than 0.25 in (6 mm) per 10 ft (3 m) while the concrete is still
plastic. Ensure that concrete sidewalk constructed as curb cut (wheelchair) ramps has a
rough or textured finish.
3) Concrete Paved Ditches. Ensure that the surface of the bottom and sides of
paved ditches are uniform and true to grade and cross section. Ensure that straight‐
grade tangents do not deviate more than 1 in (25 mm) within 10 ft (3 m) when tested
with a 10 ft (3 m) straightedge. Do not allow deviation if it reduces the ditch paving
thickness, causes water to pond, or alters the direction of flow. Finish the ditch paving
by floating with wood or metal floats to bring mortar to the surface to cover the coarse
aggregate. Use reinforcing that conforms to Plan details if required.
4) Concrete Curbs, Gutters, and Median. Finish according to Subsection
441.3.05.C.2, “Placing and Finishing.” Remove face forms as soon as possible and finish
the exposed surfaces with a wood float. Use a straightedge to test the edge of the
gutter and top of the curb and median to conform to the requirements for the adjacent
pavement. Irregularities shall not exceed 0.25 in (6 mm) in 10 ft (3 m). Place the curb
and gutter using a machine as long as the results are satisfactory.
5) Curb Cut Wheel chair Ramps. Construct a Type I, II, or III ramp according to
Georgia Standard 9031W. Tie ramps into adjacent paved or unpaved sidewalk and use a
rough or textured finish.
3. Joints
Follow these procedures to construct joints on slopes, ditches, sidewalks, and curbs, gutters, and
medians.
a. Slope Paving
Place paving on slopes in horizontal or vertical courses, but not a mixture of both.
1) Construct horizontal courses approximately level and at least 3 ft (1m) but no
more than 6 ft (1.8 m) wide measured along the slope.
When needed, construct trapezoidal courses at the top and bottom to accommodate sloping berm and
ditch line conditions.
2) Edge the paving at construction joints between courses with a 0.25 in (6 mm)
radius tool.
Section 441—Miscellaneous Concrete
Page 45
3) Provide vertical contraction or construction joints spaced along the horizontal
course at right angles to the horizontal construction joints at approximately 40 ft (12 m)
intervals, in line not staggered.
No other vertical lines will be required in horizontal courses.
When using vertical contraction joints, cut them with a tool one‐third the depth of the paving during the
finishing operation. Edge the contraction joints the same as construction joints.
Vertical courses approximately equal and at least 3 ft (1 m) but no more than 5 ft (1.5 m) wide across
the plane of the slope. The desired width is 4 ft (1.2 m). Horizontal lines are not required in vertical
courses.
Separate slope paving from the masonry of structures, sidewalks, curbs, and rigid‐type roadway
pavements of preformed joint filler that are 0.5 in (13 mm) thick.
b. Concrete Paved Ditches
Form joints in concrete paved ditches as follows:
1) Space contraction joints at 30 ft (9 m) intervals.
2) Place expansion joints only where the paved ditch joins the roadway pavement
or some other structure.
3) Do not use joint sealers for expansion or contraction joints.
c. Concrete Sidewalk
Form transverse contraction joints using a tool designed to form a groove one‐third the depth of the
sidewalk at intervals shown on the Plans.
Where sidewalks abut the curb and gutter, ensure that alternate joints coincide. Round the edges with a
0.25 in (6 mm) edger. Make expansion joints according to the materials, dimensions, and locations
specified on the Plans.
d. Concrete Curbs, Gutters, and Medians
Form contraction joints or expansion joints on curbs, gutters, and medians.
1) Contraction Joints. Ensure that joints in curb, gutters, and medians are spaced
the same as the joints in paving. Form joints by using metal divider plates or sawing
them as in Section 430.
Form joints at least one‐fifth but not greater than one‐fourth the depth of the concrete. Except for
sawed joints, finish the joints with a 0.25 in (6 mm) edging tool.
For curbs, gutters, and medians adjacent to pavement other than concrete, contraction joints shall be as
follows:
For header curb and combination curb and gutter, install contraction joints spaced no more than 20 ft
(6 m) apart.
Section 441—Miscellaneous Concrete
Page 46
For gutter median, install a contraction joints spaced no more than 20 ft (6 m) apart.
2) Expansion Joints. Form expansion joints according to the Plan details or as
directed. Ensure that they coincide with the expansion joints in the adjoining pavement
or gutter.
Cut the joint fillers to the same cross section as the construction. Trim flush the material that protrudes
after the concrete is finished.
When miscellaneous concrete items are not adjacent to concrete construction, provide expansion joints
at an interval of at least 500 ft (150 m).
e. Curb Cut Wheelchair Ramps
Locate and form expansion joints for curb cut wheelchair ramps according to Georgia Standard 9031W
for ramp Type I, II, or III.
4. Curing
Use curing methods specified in Subsection 430.3.05.L, “Cure the Concrete.” (see below) Ensure that the
membrane curing compound is Type 2, if used. Pack honeycombed areas immediately after removing
the forms.
[L. Cure the Concrete
Immediately after finishing the concrete, cure the entire surface when the concrete will not mar. Use one
or more of these
methods:
1. Impervious Membrane Method
To use this method:
a. Spray the entire surface of the pavement with white pigmented curing compound immediately after
finishing
the surface and before the concrete has set.
If the pavement is cured initially with cotton mats, burlap, or cotton fabric, apply the compound after
removing
the mats.
NOTE: Do not apply curing compound during rain.
b. Use mechanical sprayers to apply curing compound under pressure at a minimum rate of 1 gal per 150
ft² (1 L
per 3.5 m²).
c. Thoroughly mix the compound with uniformly dispersed white pigments.
d. During application, use a mechanical device to stir the compound continuously.
Section 441—Miscellaneous Concrete
Page 47
e. Use a hand sprayer (if required) to spray odd widths, odd shapes, and concrete surfaces exposed by
removing
forms.
f. Do not apply curing compound to the inside faces of joints to be sealed.
g. If the membrane film becomes damaged within the curing period, repair the damaged portions
immediately with
additional compound.
2. White Polyethylene Sheeting
To use this method:
a. Cover the top surface and sides of the pavement with polyethylene sheeting. Lap the units at least 18
in (450
mm).
b. Place the sheeting and weigh it down so that it contacts the surface.
c. Extend the sheeting beyond the edges of the slab at least twice the thickness of the pavement.
d. Unless otherwise specified, maintain the covering in place for 72 hours after placing the concrete.
3. Burlap, Cotton Fabric, or Other Methods
Contractors may cure the pavement with burlap, cotton fabrics, or other materials if the section remains
wet for the
duration specified by the Engineer.
4. Cold Weather Curing
To use this method:
a. Remove and replace concrete that freezes before the initial set time at no cost to the Government.
b. Use polyethylene or canvas to protect concrete that has set but is exposed to freezing temperatures
within 24
hours of placement. Ensure that the internal concrete temperature is above freezing for at least 24 hours
after
placing the concrete.
c. Obtain approval from the Engineer to use other protection methods such as hay, straw, or grass, or to
change the
duration of the protection.]
D. Backfilling
Section 441—Miscellaneous Concrete
Page 48
Backfill the areas as soon as possible without damaging the work.
E. Clean‐Up
When concrete work is complete, clean each surface. Protect the work from stains or other damage
until Final Acceptance.
441.4 Measurement
A. Concrete Slope Paving
Omitted
Miscellaneous Concrete
B. Concrete Sidewalks
Concrete sidewalks are measured in square yards (meters) of the specified thickness, complete in place
and accepted. The length is the actual measured length along the surface. The width is the Plan width or
as directed. Excavation and backfill are not measured separately for payment.
C. Concrete Paved Ditches
The area measured for payment is the square yards (meters) of exposed surface area, exclusive of top
edges, of the specified thickness placed according to the Plans or as directed. Reinforcing steel,
excavation, preparation of subgrade including Type I backfill, forms, and concrete in toe or edge walls
are not measured separately for payment.
D. Concrete Curbs, Gutter, Median, Pavement, and Combination Curb and Gutter
The following are measured by the linear foot (meter) along the face of the curb:
Concrete curb and gutter
Concrete curb
Concrete header curb
The following are measured by the square yard or by the linear foot, whichever is specified:
Concrete gutter
Concrete valley gutter
Concrete valley gutter with curb
Concrete median pavement
Concrete gutter with raised edge
The length used to compute the square yards (meters) or linear foot (meter) is measured along the
center line of the gutter. The width is the total width of the gutter including the curb or raised edge.
Concrete doweled integral curb includes dowels.
E. Concrete Headwalls
Headwalls are measured for payment per Each.
Section 441—Miscellaneous Concrete
Page 49
F. Concrete Spillways
Concrete spillways regardless of the type specified are measured by the actual number poured complete
and accepted.
G. Concrete Slope Drains
Concrete slope drains are measured in square yards (meters) along the surface, complete and accepted.
H. Velocity Dissipators
Velocity dissipators are measured in square yards (meters), surface measure, complete and accepted.
I. Concrete Driveways
Driveway pavement is measured along the surface from the paving edge or back of the curb to where
old and new concrete join. The width is the average width constructed.
Miscellaneous Concrete
J. Curb Cut Wheelchair Ramps
For new construction, curb cut wheelchair ramps will not be measured. For new construction, linear feet
of curb and gutter will include the transitioned curb in front of ramps and square yards of concrete
sidewalk will include ramps. No additional payment will be made for curb cut ramps.
For existing sidewalks, curb cut wheelchair ramps are measured as the actual number formed and
poured, complete and accepted. No additional payment will be made for sawing existing sidewalk and
removal and disposal of removed material for new ramp construction.
441.5 Payment
These Items, measured as specified above, will be paid for at the Contract Unit Price per each, per
square yard, per linear foot, per cubic yard, or per each.
Curbs, Gutters, Combination Curb and Gutter, Headers, and Medians
Item No. 441 Concrete curb and gutter, 6 in x 24 in type 2 Per linear foot
Item No. 441 Concrete valley gutter, 6 in Per square yard
Headwalls
Item No. 500 Headwall, 18” Concrete Per each
Section 441—Miscellaneous Concrete
Page 50
Driveway Concrete
Item No. 441 Driveway concrete 6 in thick Per square yard
Page 51
Section 535—Painting Structures
535.1 General Description
This work consists of painting existing steel structures. The work also includes protecting traffic and
property.
A. Referenced Documents
SSPC Guide 6I (CON), Class 3, 1992 edition
SSPC Guide 7I (DIS), Section 5
SSPC‐SP6, “Commercial Blast Cleaning”
SSPC‐SP7, “Brush‐Off Blast Cleaning”
OSHA Standards 29 CFR 1910 and 29 CFR 1926
Toxicity Characteristic Leaching Procedure (TCLP)
EPA “Uniform Hazardous Waste Manifest”
535.1.01 Submittals
At least 4 weeks before beginning the work, make the following submittals to the Engineer for approval:
A. Health and Safety Responsibilities
Provide effective engineering and work practice controls to protect employee health and safety.
1. Comply with all relevant Environmental Protection Agency (EPA), Resource Conservation and
Recovery Act (RCRA), Comprehensive Environmental Response, Compensation and Liability Act
(CERCLA), Occupational Safety and Health Act (OSHA), and Environmental Protection Division
(EPD) Regulations.
2. Certify to the Engineer that personnel involved with lead paint removal operations (including
rigging and material handling personnel) have received training and understand the applicable
parts of the latest edition of OSHA Standards 29 CFR 1910 and 29 CFR 1926, including any
amendments. Have the certification signed by all personnel involved with lead paint removal.
3. Provide test results from an OSHA Certified Laboratory showing blood lead levels of employees
that may be exposed to lead during the Project.
4. Provide a medical monitoring schedule to verify acceptable blood lead levels during the Project
and after the Project is completed.
B. Blast Cleaning Containment System
1. Before beginning work at each bridge, submit design and drawings of the proposed
containment system to the Engineer for review and approval. Include tarpaulin data sheets to
verify that the material is airtight, and tightly secured at the seams. Do not use burlap or open
weave materials.
Section 535—Painting Structures
Page 52
2. When the proposed containment system will induce large loads on the existing
structure, the Engineer may direct the Contractor to submit an analysis of the load that will be
added to the existing structure by the containment system and blast waste. Have a licensed
Professional Engineer registered in the State of Georgia with bridge experience perform and
stamp the load analysis. Ensure that the analysis shows that the system will not induce a load on
the bridge that overstresses it or affects the structural integrity of the bridge.
3. Do not allow the containment system or equipment to violate the minimum bridge
clearances shown on the Plans, unless otherwise approved by the Engineer.
C. Emergency Contingency Plan
Submit to the Engineer for review and approval an emergency contingency plan for cleaning up spills
from failure of the containment system, spent material recovery system, or storage containers. Define
procedures for spills or releases of waste and indicate the training of workers handling the waste as
required by RCRA.
D. Spent Material Sampling Plan
Submit in writing to the Engineer for review and approval the proposed method for collecting the spent
material. Include a sampling plan that conforms to EPA SW849. This submittal will also include the name
of the company(ies) and responsible person(s) that will sample, treat, and haul the spent material.
E. Material Safety Data Sheets
Submit Material Safety Data Sheets on the abrasive and paint materials that will be used.
F. Hazardous Waste Transporter Information
Provide the name and EPA identification number of each licensed Transporter used for shipping
hazardous waste to a treatment, storage, or disposal facility.
G. Permitted Site Information
Provide the name and EPA identification number, phone number, and address for each permitted off‐
site treatment, storage, or disposal facility to which the waste will be shipped.
H. Accredited Laboratory Information
Provide the name of the Environmental Lead Laboratory Accreditation Program (ELLAP) accredited
laboratory that will perform the TCLP tests.
The Engineer will forward a copy of these submittals to the Office of Materials and Research for review.
535.2 Materials
Ensure that materials meet the requirements of the following Specifications:
Material Section
Abrasives for Blast Cleaning Note 1*
Section 535—Painting Structures
Page 53
Paint 870
Note 1*
Use low dusting mineral abrasives which contain a minimum of ten percent (10%) by weight G‐80 steel
grit blended homogeneously throughout the blasting abrasive or 100% steel grit. Alternate abrasive
mixtures proposed by the
Contractor require approval by the Macon‐Bibb County Engineer before use. Abrasives shall contain no
more than 100 ppm of any corrosive compound such as sulfate or chloride. Abrasives shall not contain
EPA characteristic compounds such as lead, chromium, or arsenic which can be detected by the EPA
Toxicity Characteristic Leaching Procedure (TCLP). The mineral abrasive used to blend with steel grit will
be listed in the Department's Qualified Products Manual.
535.2.01 Omitted
535.3 Construction Requirements
535.3.01 Personnel
A. Contractor Certification
Ensure that no Contractor performs work on this Item who is not certified.
To become certified to remove lead paint, either:
Be SSPC certified for hazardous paint removal according to the SSPC‐QP2 Contractor Certification
Program
Have certified structural steel painting supervisors onsite during Project lead paint removal or spent
materials activities (collecting, storing, separating, treating, and moving spent materials).
535.3.02 Equipment
A. Brushes
Preferably, use brushes with round or oval cross sections. If using flat brushes, ensure that the maximum
width is 4 in (100 mm).
For surfaces inaccessible to brushes, apply paint with sheepskin daubers made for painting.
Application of inorganic zinc by brush is prohibited except for small areas and touch up work.
B. Spray Equipment
If spraying paint, use air, cold airless, or hot circulating airless equipment. Spray equipment is subject to
the Engineer’s approval.
Use spray equipment that can constantly agitate the paint. Also, use equipment with a device that
thoroughly mixes paints in their shipping containers before the paints are removed.
Section 535—Painting Structures
Page 54
Water traps are required as follows:
When using air spray equipment, ensure that the air lines in the system have suitable water traps.
For cold airless spray equipment, water traps are not required in the air lines; use them if desired.
C. Rollers
Rollers are subject to the Engineer’s approval.
Use rollers suitable to the type of paint applied and the work areas involved. Provide pans for dipping
the rollers into the paint.
Follow these restrictions:
Do not use worn rollers.
Do not use rollers to apply special protective coatings or paints to piling and swaybracing.
If a surface is inaccessible to rollers, apply the paint with sheepskin daubers made for painting.
Ensure that the system applicator has the following:
Wet‐film gauge
Dry‐film gauge
Surface thermometer
Sling psychrometer
Abrasive blasting finish gauge
During and after field cleaning and painting, furnish a safety belt and a lift truck, bucket truck, or
snooper truck to the Engineer’s satisfaction to inspect the cleaning and painting operation.
E. Protection Equipment
Furnish signs, warning lights, barricades, enclosures, and watchmen as required by the Manual on
Uniform Traffic Control Devices or by the Engineer.
535.3.03 Preparation
Refer to Subsection 535.3.05B.1, “weather conditions” before performing any cleaning operations.
A. Omitted
B. Clean Existing Steel Structures
Clean only as much metal as can be painted before it rusts. If surfaces rust after cleaning, clean them
again before painting them.
Blast clean existing steel structures as follows:
1. Construct protection devices. Assume responsibility for damages to vehicles, persons, or
property caused by cleaning operations.
Protect the following from blast‐cleaning hazards:
Section 535—Painting Structures
Page 55
Portions of the structure (superstructure, substructure, and highway appurtenances) that could be
damaged by the blast cleaning
Existing pedestrian, vehicular, and other traffic on, underneath, or adjacent to the structure Construct
protection devices as follows:
a. Cover or shield portions of the structure that could be damaged.
b. Construct a system that protects traffic from direct blasting and prevents abrasive
materials and debris from spreading and creating a traffic hazard.
c. If blast cleaning disrupts traffic flow, stop cleaning or clean behind screens.
d. If the protection devices are not providing protection, stop the work and correct the
problem.
Do not begin work until effective corrections are made.
e. Before reopening work areas to traffic, remove abrasive material and debris deposited
on the pavement, shoulders, or slope paving in the area.
2. Prepare the structures for blast cleaning as follows:
a. If the Project Inspector requires, remove railings, nameplates, and other interfering
parts from surfaces to be cleaned and painted.
b. Straighten bent metal.
c. Before blast cleaning a beam or girder, remove dust and debris from the top of the
bottom flange.
3. Remove all coats of paint to clean, bare metal by blast cleaning or other approved
means.
The extent of cleaning shall be SSPC‐SP6, “Commercial Blast Cleaning,” with an anchor
pattern between 1.0 and 2.0 mils. Anchor patterns greater than 2.0 mils (0.051 mm) will require that the
primer be applied at a thickness of at least 1 mil over the anchor pattern or that the steel be re‐blasted
unless otherwise approved by the Engineer.
4. After blast cleaning and before painting, prepare the steel surfaces as follows:
a. Remove sand, dust, and other foreign matter from the following:
Deck
Piers
Railing
Other adjoining parts of the structure
Slope paving
b. Remove any fins, tears, or slivers from the steel.
c. Remove burred or sharp edges that appear on any steel members.
Section 535—Painting Structures
Page 56
d. Have the Engineer inspect each span or unit of work.
e. Do not begin painting until the Engineer approves the spans or units of work.
5. Contain the paint chips, abrasive particles, and dust or debris (spent material) caused by
cleaning and blasting as follows:
a. Contain spent material according to the 1992 edition of SSPC Guide 6I (CON), Class 3.
The containment materials and support structure may be flexible or rigid.
b. Ensure that tarpaulins are airtight and secure at the seams.
c. Do not use burlap or open‐weave materials.
d. Seal seams and joints by taping or overlapping tarps at least 24 in. Overlap the entryway
at least 3 ft.
e. Use negative pressure and verify it as follows:
Verify pressure through the concave nature of the containment materials, taking into account wind
effects.
Observe air flow using smoke or other visible means inside or outside the containment.
f. Filter the air exhausting from the containment with a properly sized dust collector, bag
house, or other approved method.
g. During abrasive blasting operations, ensure that the cross‐draft and downdraft air
movements within the containment comply with OSHA Standard 29 CFR 1910.94.
6. Additional blast‐cleaning requirements for bridges over waterways:
a. Ensure that there is no scum on the surface of the water outside a 200 ft (60 m) limit of
the bridge. Stretch a floating boom across the waterway at or before this 200 ft (60 m) limit
on the downstream and downwind sides of the bridge to contain floating spent material.
b. If floating residue is found outside this 200 ft (60 m) limit, the Engineer will consider
protection inadequate and will require further containment measures.
c. If the wind velocity is high enough to blow the residue outside the 200 ft (60 m) limit,
the Engineer will temporarily suspend the blast cleaning.
d. Provide a flotation device in the water underneath the area being blast cleaned to
collect the spent material.
e. If the stream is too shallow for a barge, erect a temporary platform or tarp arrangement
to collect the spent material.
7. Alternate Containment System
If desired, propose an alternate method for containing the dust and spent materials from blast cleaning
the structural steel.
Section 535—Painting Structures
Page 57
The Engineer may reject a proposed alternate method that does not satisfy the Engineer’s concerns for
the safe removal and containment of lead‐based paint from bridge structures.
Submit the proposal for evaluation and approval as follows:
a. Submit a detailed, written proposal describing the alternate containment and blasting
method.
b. Include in the description specific information on materials and equipment, noise levels,
and worker safety and health.
c. Supply references of other locations where the alternate method has been used.
d. The Engineer will review the information submitted and may reject the proposal or issue
a conditional approval.
e. If the Engineer grants conditional approval, demonstrate the alternate method for
containment and blast cleaning on a trial basis.
1) The Engineer will evaluate the effectiveness of dust and spent material
containment, worker safety and health concerns, and noise levels.
2) If the Engineer finds the alternate method unacceptable, the Engineer may
reject it and require work according to this Specification.
3) If the Engineer approves the alternate method, the Contractor will receive no
additional payment above the established Contract Unit Price.
8. Handling Spent Materials
Handle spent materials according to the following requirements:
a. Collect the spent material daily and store it in sealed waste disposal containers.
b. Use waste containers that are approved by the Engineer and located where they will not
cause a potential hazard.
c. Store waste containers in a temporary, fenced, secured area that is not located in a
storm water runoff course, in standing water, nor on Engineer property. Ensure compliance
with the requirements of EPA 40 CFR 264.14 and 40 CFR 264.18.
d. Label waste containers in compliance with hazardous waste laws.
e. Omitted
f. Test the material using certified independent laboratory in accordance with the Toxicity
Characteristic Leaching Procedure (TCLP).
g. Collection, storage, sampling, and testing shall be performed in accordance with EPA
RCRA Regulations (40 CFR 240‐299).
h. Forward a copy of all TCLP results to the Engineer.
Section 535—Painting Structures
Page 58
i. If the TCLP toxicity test results do not classify the spent materials as a hazardous waste,
uniformly blend twenty percent Portland cement with the spent materials and solidify the
mixture before disposing of it at a licensed solid waste landfill. The cost of treatment and
disposal of non‐hazardous spent material is considered incidental to the pay item.
j. If the TCLP test results classify the material as a hazardous waste, treat the material to
the Land Disposal Restriction standard of 0.75mg/l. The waste shall not be disposed of until
authorized by the Engineer.
1) If the waste is to be treated on‐site, submit a waste analysis plan to the regional
EPA office in accordance with 40 CFR 264.13 within 30 days of receipt of the TCLP
results.
2) If the waste is to be treated off‐site, submit TCLP results to the EPA permitted
hazardous waste treatment facility.
k. Forward a copy of all manifests and pertinent documents to the Engineer and to OMR.
9. Sampling for Lead Paint Residue
a. Use the sampling plan listed below or a similar plan that conforms to EPA SW 846,
Chapter 9 Test Methods for Evaluating Solid Waste Physical/Chemical Methods.
Ensure the plan includes the following:
1) Who will be responsible for the sampling
2) How often samples will be taken
3) How the samples will be obtained
4) Where the samples will be taken
5) How the samples will be handled
6) How the sample results will be tied back to the waste from which it was
sampled.
b. Inform the Project Personnel and Independent Assurance Engineer as to when (date and
time) the samples will be taken. The Engineer will monitor the sampling procedure and the
Project Personnel will enter all pertinent information in a logbook. Information to be
recorded is as follows:
1) Project and Contract ID numbers
2) Sampling points
3) Field contact personnel
4) Producer of waste
5) Type of process producing the waste
Section 535—Painting Structures
Page 59
6) Type of waste
7) Total number of samples
8) Number of drums each sample will cover
9) Which bridge location and the drum number i.e. 1‐10, 11‐18 that the sample will
cover.
a) Label all of the drums on the project. Ensure that the labels are weatherproof
and include the following:
The Date
The Project Number
The Contract ID Number
The Bridge Location
Assign drums a series of consecutive numbers, i.e.,1‐40.
c. Take one grab sample (using random sampling technique) from a drum for each bridge
location. Use a thieving device to secure samples from each of the drums. The minimum
sample size is 0.66 lb which is about a cupful.
d. Samples may be taken by the paint Contractor or his/her consultant who will treat the
waste.
1) Send the samples to a certified private testing lab.
2) Attach a Sampling Analysis Request (sample card) to the samples which
includes: a) The Date
b) Project Number
c) Contract ID number
d) Bridge Location
e) Name of collector
f) Place of collection
g) Number of drums from Bridge each sample will cover, and
h) Drum numbers, i.e. 1‐10, 11‐18 that sample will cover.
3) Include this information on the test report and the manifest so that the waste
on the manifest can be keyed to the results on the TCLP report.
4) Ensure that a chain of custody form accompanies the sample and is returned
with the test results.
e. Test the samples for EPA Method 1311, Toxicity Characteristic Leaching Procedure
(TCLP).
Section 535—Painting Structures
Page 60
f. Test one (1) sample for each bridge location.
1) If the results are 5 mg/l or greater leachable lead, the waste is to be declared
hazardous and no further testing is needed until the waste has been treated. After
treatment, the waste shall be re‐sampled and retested in accordance with an approved
sampling plan and shall be below 0.75 mg/l before disposal.
2) If the results are below 5mg/l, the waste is to be declared non‐hazardous, then
the contractor or his/her consultant shall uniformly blend twenty percent Portland
cement with the spent material and solidify the mixture before disposing of it at a
licensed solid waste landfill.
g. Additional samples must be acquired according to EPA SW 846 and SSPC‐Guide 7
Section 5.6.5.
h. Mail the Test reports and manifests to the Engineer's office.
If the TCLP toxicity test results classify the spent materials as a hazardous waste, treat the waste either
on‐site or off‐site to the Land Disposal Restriction Standard of 0.75 mg/l. Do not dispose of the waste
until authorized by the Engineer. Hazardous waste material may be treated off‐site if the treatment is
performed by a licensed hazardous waste treatment facility in accordance with EPA and EPD guidelines.
Forward a copy of all manifests and other pertinent documents to the Engineer and to OMR. These
documents will be maintained in the project file for three years.
If after treatment, the spent material is classified as a hazardous waste by the TCLP test, retreat it until
the Universal Treatment Standard is met.
10. Handle hazardous waste as follows:
a. The Contractor is responsible for complying with the hazardous waste laws when
performing the Work. Obtain a separate United States Environmental Protection Agency,
Generator I.D. Number for each project where the spent material is hazardous waste
according to the Toxicity Characteristic Leaching Procedure (TCLP) results.
Obtain the generator I.D. number from the Georgia Environmental Protection Division, Hazardous Waste
Management, (404) 656‐2833.
Obtain the Generator I.D. Number within 30 days of receiving the TCLP results and provide copies of the
number to the Macon‐Bibb County Engineer.
b. Dispose of hazardous spent material only at a licensed hazardous waste disposal facility.
c. If the disposal facility requires it, send a sample of spent material for confirmation
testing before delivering the shipment.
d. Transport the waste to the facility using EPA‐approved licensed waste haulers.
e. Document each truckload of hazardous waste using an EPA “Uniform Hazardous Waste
Manifest.”
Section 535—Painting Structures
Page 61
f. According to EPA and EPD rules, provide GDOT and the Georgia EPD notification and
certification of treated hazardous spent abrasives. Include the following:
Name and address of facility receiving the shipment Description of the waste as
initially generated, including the applicable EPA Hazardous Waste Number(s) and
treatability group(s)
Treatment standards applicable to the waste at the initial generation point
Signature of an authorized Contractor representative on the certification
C. Omitted
D. Omitted
535.3.04 Omitted
535.3.05 Construction
A. Provide Protection
Protect the structure, adjoining property, and the public from the dangers and damages of cleaning and
painting.
Protect the following:
Pedestrian, vehicular, and marine traffic on or underneath the structures being painted
Structures
Slope paving
Clean slope paving stained during painting to the Engineer’s satisfaction.
B. Meet General Painting Requirements
Follow these requirements when painting new and existing steel structures:
1. Weather Conditions
Cleaning or Painting shall not take place during windy or gusty conditions unless the contractor can
demonstrate to the satisfaction of the Engineer that containment is sufficient to prevent the escape of
paint overspray or spent material. If any paint overspray or spent material is detected outside
containment areas, cease all operations until clean up has been completed. Do not recommence
cleaning or painting operations until additional measures have been taken to prevent any future escape
of spent material and/or paint overspray.
When the Plans specify System VI (waterborne), ensure that the minimum air and surface temperature
is 50 °F (10 °C). Comply with the other weather requirements listed below.
When the Plans specify System VII, ensure that the minimum air and surface temperatures are
above 35 oF (2 oC) and the relative humidity is greater than 50% when applying the inorganic zinc primer.
Section 535—Painting Structures
Page 62
Apply System VII waterborne intermediate and top coats only when the temperatures of both the air
and surface are above 50 oF (10 °C).
For Systems IV and V (alkyd), apply paint only when the air and surface temperatures are both above 40 oF (4 °C).
Weather Requirements for Painting All Systems
Maximum surface temperature 140 °F (60 °C)
Relative humidity Below 85%
Minimum surface temperature 5 °F (3 °C) above dew point
Follow these weather restrictions:
Do not apply paint to surfaces that are damp or otherwise unsatisfactory as determined by the
Engineer.
Do not paint in open yards or on erected structures when the metal is hot enough to cause the
paint to blister or produce a porous film.
Do not paint metal hot enough to cause oil separation in the alkyd paint.
Do not paint metal when freezing weather 32 oF (0 oC) is forecast or expected before the paint
can dry.
Do not store at temperatures below 32 oF (0 oC)or above 100 oF (38 oC). When outdoor
temperatures exceed these limits, paint shall be stored in an appropriate indoor location.
2. Oxidation
If a prime coat on structural steel fades or chalks because of oxidation, thoroughly remove the oxidation
by brushing or by washing with water until the sound prime coat is visible.
3. Paint Thinning
Do not thin or dilute paints.
4. Application Methods
Thoroughly mix paints in their shipping containers using mechanical devices before removing the paint.
For inorganic zinc primers, add the powder component to the liquid component with thorough stirring,
and continue stirring until the powder is well dispersed. Strain the mixture through a 30‐60 mesh sieve
to remove large particles. Use pressure pots equipped with a mechanical agitator, which will remain in
motion throughout the application.
Ensure that the paint formulation matches the application method (brush, roller, airless spray, or air
spray).
Apply paint neatly by brushing, spraying, or rolling.
Section 535—Painting Structures
Page 63
When using brushes or rollers, apply the paint as follows:
a. Produce an even coating covering the metal or the previous coat.
b. Work the paint into corners and crevices.
c. Keep enough paint on rollers and overlap the applications to avoid unsightly or mottled
areas.
Use the paint numbers shown in the Table of Application Methods, below.
Table of Application Methods
Brush Roller Airless Spray Hydraulic Air Spray
Ordinary Exposure Green System IV (Lead Free Alkyd)
1A 1A 1A X
1A 1A 1A X
2A 2A 2A X
3B 3B 3B X
X X X X
Table of Application Methods
Brush Roller Airless Spray Hydraulic Air Spray
Heavy Exposure Green System V (Lead Free Alkyd)
1A 1A 1A X
1A 1A 1A X
1A 1A 1A X
2A 2A 2A X
3B 3B 3B X
Ordinary Exposure Green System VI (Waterborne)
1W 1W 1W 1W
Section 535—Painting Structures
Page 64
1W 1W 1W 1W
2W 2W 2W 2W
3W 3W 3W 3W
Ordinary exposure Green System VII (Zinc Primer)
X X Inorganic Zinc Primer X
2W 2W 2W 2W
3W 3W 3W 3W
5. Paint Systems and Dry Film Thickness
Apply the minimum required dry film thickness and the additional coats according to the paint system
required on the Plans.
Table of Paint Systems and Minimum Required Dry Film Thickness
No. of Coats Color of Coats Thickness, mils (mm)
Ordinary Exposure Green System IV (Lead Free Alkyd)
Primer Red 2.0 (0.051) to 5.0 (0.127)
Touch‐Up Red *
2nd Coat Buff 2.0 (0.051) to 5.0 (0.127)
3rd Coat Green 1.0 (0.025) to 3.0 (0.076)
4th Coat None X
Heavy Exposure Green System V (Lead Free Alkyd)
Primer Red(T) 2.0 (0.051) to 5.0 (0.127)
Touch‐Up Red *
2nd Coat Red 2.0 (0.051) to 5.0 (0.127)
3rd Coat Buff 1.5 (0.038) to 5.0 (0.127)
Section 535—Painting Structures
Page 65
Table of Paint Systems and Minimum Required Dry Film Thickness
No. of Coats Color of Coats Thickness, mils (mm)
4th Coat Green 1.0 (0.025) to 3.0 (0.076)
Ordinary Exposure Green System VI (Waterborne)
Primer Brown 3.0 (0.076) to 5.0 (0.127)
Touch‐Up Brown *
2nd Coat Buff or White 3.0 (0.076) to 5.0 (0.127)
3rd Coat Green 3.0 (0.076) to 5.0 (0.127)
4th Coat None X
Ordinary Exposure Green System VII (Zinc Primer)
Primer Gray 3.0 (0.076) to 5.0 (0.127)
2nd Coat Buff or White 2.0 (.0.051) to 5.0 (0.127)
3rd Coat Green 2.0 (0.051) to 5.0 (0.127)
4th Coat None X
* = 2.0 (0.051) for touch‐up coats
(T) = Tinted
6. Proper Drying
Ensure that each coat is thoroughly dry and cured before applying the next coat. Allow at least 24 hours
between coats.
If weather conditions and paint type require, allow longer periods between coats.
7. Cracks and Cavities
Before applying the second field coat, fill small cracks and cavities that are not sealed watertight by the
first field coat using the following
Plan‐Required Paint System Fill Mixture
Section 535—Painting Structures
Page 66
IV or V Pasty mixture of zinc hydroxy phosphite and linseed oil
VI Pasty mixture recommended and supplied by the manufacturer
VII Pasty mixture recommended and supplied by the manufacturer
C. Omitted
D. Paint Existing Steel Structures
Paint existing steel structures as follows:
1. Prevent paint overspray by using containments.
2. The weather conditions specified for new steel structures described in Subsection
535.3.05.B also apply to existing steel structures.
3. Apply the correct colors and number of coats as follows:
Only steel which has undergone complete removal of all coats and which has a surface cleanliness
conforming to SSPC SP‐6 may be coated with System VI.
Give this steel one full prime coat and two weather coats, all of the color and type required by the
Special Provisions or Plans. If succeeding coats are of the same type and color, tint one of the underlying
coats as required by the Specifications.
4. The drying requirements of Subsection 535.3.05.B.6 specified for new steel structures
shall apply to existing steel structures.
5. The paint thinning requirements of Subsection 535.3.05.B.3 specified for new steel
structures shall apply to existing steel structures.
6. Painting Of Surfaces:
a. Methods of Application: The requirements of Subsection 535.3.05.B.4.as
specified for new steel structures shall apply to existing steel structures.
b. Cracks And Cavities: The requirements of Subsection 535.3.05.B.7 as specified
for new steel structures shall apply to existing steel structures.
c. Paint Thickness: The minimum required dry film thickness as specified in
Subsection 535.3.05.B.5 and the
additional coats specified in Subsection 535.3.05.B.5 for new steel structures shall apply to existing steel
structures. However, when new paint is applied over existing sound paint, the required wet film
thickness of the new coats shall be that required by the Special Provisions or Plans.
Section 535—Painting Structures
Page 67
7. Apply the minimum required dry film thickness and the additional coats specified in the
Table of Paint Systems and Minimum Required Dry Film Thickness.
However, when applying new paint over existing sound paint, comply with the required wet film
thickness specified by the Special Provisions or Plans for new coats.
8. After completing the painting, replace the railings, name plates, and other interfering
parts removed (as described in Subsection 535.3.03.B, “Clean Existing Steel Structures” step 2.a)
to the Engineer’s satisfaction. E. Paint Steel H‐Piling, Metal Shell Piling, and Steel Swaybracing
Paint this material as follows:
1. Weather Conditions
Except as specified below, apply paint in the weather conditions specified in Subsection 535.3.05.B.1,
“Weather
Conditions.”
a. Painting in open yards or on erected structures shall not be done when the metal is
sufficiently hot to cause the paint to blister or produce a porous film.
b. Metal shall not be painted when freezing weather [ 32 oF (0 oC) ] is forecast or expected
in the time that would occur before the paint has dried.
2. Thinning Paint
Do not thin or dilute pile paints.
3. Number of Coats and Color
Unless the Plans require a No. 1P or 2P system, described in Subsection 870.2.05.A.1, “Paint for Steel
Piling and Swaybracing,” paint steel H‐piling, metal shell piling, and steel swaybracing with a System VII
paint system.
Apply a No. 1P system as follows:
a. When using a No. 1P system formulated as a first application primer and a separate
finish coat, ensure that containers are clearly labeled as primer or finish coat.
b. Apply the primer first.
c. Apply successive coats using either primer or finish coat.
d. Ensure that the final coat is a finish coat
4. Method of Application
Apply the black paints noted in Subsection 535.3.05.E.3, “Number of Coats and Color” using either
brushes or sprayers.
When using a brush, apply the paint as follows:
a. Apply a thick application of paint to be plastered or troweled on the steel surfaces.
Section 535—Painting Structures
Page 68
b. Brush out the paint only as required to obtain uniform thickness; do not attempt to
brush it out neatly. c. Work the paint into corners and crevices.
5. Application Rate
For each coat, apply at least 1 gal of paint type per 60 ft². (0.7 L/m2). Ensure that the total dry‐film
thickness of paint coats is as specified in Subsection 535.3.05.E.6, “Thickness of Paint,” below.
6. Thickness of Paint
Ensure that the final, dry‐film thickness of the completed work is at least 25 mils (0.635 mm).
Apply additional coats to achieve the minimum dry‐film thickness at no expense to the Government. 7.
Extent of Paint
Paint to the following extent:
Coat exposed piling with a System VII paint system unless a No. 1P orNo. 2P system is specified on the
Plans.
Coat piling in the stream bed and within 10 ft (3 m) of the top of the stream bank with the System VII
from 5 ft (1.5 m) below the stream bed to the bottom of the concrete cap.
Coat end bent piles 2 ft below the bottom of the cap or concrete encased as defined in Subsection
520.3.05.O, “Coat and Paint Piling.”
For piling that will be encased according to Section 547, paint the piling with System VII to the extent
specified in Subsection 520.3.05.O, “Coat and Paint Piling.”
Before driving, coat test piles located in permanent surface water with a System VII according to
Subsection 520.3.05.O, “Coat and Paint Piling.”
Paint enough of the test pile to ensure that the coated portion extends 5 ft (1.5 m) below the stream
bed or bottom.
8. Drying Requirements
Ensure that each coat is thoroughly dry before the next coat is applied.
F. Apply Special Protective Coatings to Steel Piling, Steel Swaybracing, and Concrete Piling
Unless the Plans require No. 1P or 2P system, apply a System VII coating. Apply the coating to the extent
specified in Subsection 520.3.05.O, “Coat and Paint Piling.”
Ensure that coverage, wet‐ and dry‐film thicknesses, temperature considerations, primer use, and drying
and curing time comply with the manufacturer’s recommendations.
Apply the special protective coating as follows:
1. When the structure will be welded, do not apply the material until the weld is placed
and cleaned.
2. Apply the material in at least two coats by brushing.
Section 535—Painting Structures
Page 69
3. Apply the second coat at right angles to the first coat.
4. Use the elapsed time between coats recommended by the manufacturer.
5. Ensure that the finished film has no holidays and pinholes and completely covers the
underlying surface.
6. After applying the coating material, recoat damaged areas where the protection is
ineffective as determined by the Engineer.
7. Where swaybracing members will be welded to piles and painted in advance, burn off
the coating at the weld location and proceed as follows:
a. Thoroughly clean the burned area by scraping and power‐operated wire brushing before
welding.
b. After making and cleaning the weld, recoat the area.
A. Correct Defective Work
If applied paint does not meet the requirements of this Specification, remove the paint or correct it
using SSPC‐approved means.
Remove paint that is applied to improperly cleaned surfaces. Clean the surfaces and repaint them to the
Engineer’s satisfaction.
B. Meet the Required Total Dry‐Film Thickness
If the minimum required total dry‐film thickness specified for the paint system is not reached after
applying the required number of coats and colors, apply additional coats at no expense to the
Government until the required thickness is obtained.
The Government considers the applied zinc primer deficient in thickness for measured dry thickness
values less than 3 mils. If more than four deficient thickness values (one measurement per 25 ft.2 of
surface area) are found in any 200 ft2 of continuous metal section, blast clean the entire section to a
SSPC‐SP6, Commercial Blast condition. Repaint the section with inorganic primer to achieve a dry film
coating thickness of 3.0 to 5.0 mils.
Repair primed areas having excessive dry film coating thickness, coating "dry spray", visible coating
"mudcracking", visible surface hackles, handling abrasions, and missed paint in bolt holes. Repair in
accordance with the written recommendations of the paint manufacturer. Obtain the Engineer's
approval for all repair recommendations. Include current product data and application instruction
sheets with the repair recommendations.
535.3.07 Contractor Warranty and Maintenance General Provisions 101 through 150.
535.4 Measurement
The cost of painting new steel structures shall be included in the Contract Price for structural steel. No
separate payment will be made.
Section 535—Painting Structures
Page 70
Cleaning and painting existing steel bridge structures will be measured and paid for at the Contract Unit
Price for “Painting Existing Steel Structure Station or Bridge I.D. No. 021‐0170‐0.”
This includes payment for the following:
Equipment (including a “flotation device” or temporary platform on waterway bridges)
Work platform
Bucket truck or snooper truck with safety belt
TCLP testing
Materials and work necessary to remove lead‐based paint and contain the spent materials
Collection and storage of spent materials, water, and slurry generated by abrasive blasting
535.4.01 Limits
A. Spent Materials
Treatment of hazardous waste and subsequent disposal shall be paid for under a force account basis.
The Engineer will reimburse the Contractor based upon invoices from the licensed hauler and disposal
facility. An additional amount equal to 3% of the total invoices will be paid as administrative costs
incurred by the Contractor.
The costs of collecting spent material, furnishing the containers, loading the material into containers,
treating the material onsite, and loading the containers into the licensed hauling unit will not be paid for
separately. These costs are considered incidental to the pay item.
The disposal of other spent materials collected is incidental to the Pay Item “Painting Existing Steel
Structures.”
B. Piling and Steel Swaybracing
The cost of applying special protective coatings or paint to piling shall be included in the Contract Price
for piling. No separate payment will be made.
The cost of applying special protective coatings or paint to steel swaybracing shall be included in the
Contract Price for structural steel. No separate payment will be made.
535.5 Payment
Payment is full compensation for the costs, direct and indirect, of complying with the requirements of
this Specification.
Payment will be made under:
Item No. 535 Painting existing steel structure, Bridge I.D. No. 021‐0170‐0 Per lump sum
Section 550 – Storm Drain Pipe
Page 71
Section 550—Storm Drain Pipe, Pipe‐Arch Culverts, and Side Drain Pipe
550.1 General Description
This work includes furnishing and installing the following:
Storm drain pipe
Pipe‐arch culverts
Side drain pipe flared end sections
Tapered pipe inlets
Install structures according to the Specifications and the details shown on the Plans, or as directed by the
Engineer.
Use the type of pipe designated on the Plans, or acceptable alternate types when applicable.
550.2 Preparation
Before installing pipe and pipe‐arches, shape the foundation material as shown on the Plans.
—Storm Drain Pipe, Pipe
550.3 Construction
A. Drainage
Provide necessary temporary drainage. Periodically remove any debris or silt that constricts the pipe flow to
maintain drainage throughout the life of the Contract.
B. Damage
Before allowing traffic over a culvert, protect the structure by providing sufficient depth and width of
compacted backfill. Repair damage or displacement from traffic or erosion that occurs after installing and
backfilling at no additional cost to the Government.
C. Installation
1. Concrete Pipe
Lay flat‐bottom and circular sections in a prepared trench with the socket ends pointing upstream. To join
sections, use any of the following joint types:
Mortar
Bituminous plastic cement
Rubber‐type gasket
O‐ringed gasket
Preformed plastic gasket
Section 550 – Storm Drain Pipe
Page 72
If using mortar and bituminous plastic cement joints:
a. Fill the annular space with the joint material and wipe the inside of each joint smooth.
b. Construct mortar joints in the same manner, but thoroughly wet the annular space before filling
it with joint material.
c. After the initial set, protect the outside mortar from air and sun with thoroughly wet earth or
burlap cover. Install rubber‐type, O‐ring, and preformed plastic gasket joints according to the
manufacturer’s recommendations.
2. Omitted
3. Corrugated Aluminum or Steel Pipe and Pipe‐Arches
Lay pipe sections in a prepared trench, with outside laps of circumferential joints pointing upstream and
longitudinal joints at the sides. Join the sections with coupling bands, fastened by two or more bolts. Keep no
more than 2 in (50 mm) of space between adjoining sections.
Before backfilling the structure:
a. Repair exposed base metal in metal coating according to Section 645.
b. Recoat exposed base metal in bituminous coating with asphalt.
4. Smooth‐Lined Corrugated Polyethylene Pipe
Install smooth‐lined corrugated polyethylene pipe according to ASTM D 2321. Use fitting and couplings that
comply with the joint performance criteria of AASHTO Standard Specifications for Highway Bridges, Division II.
Ensure that all joints are “soiltight” as stated in the AASHTO bridge specifications.
5. Specials (Wyes, Tees, and Bends)
Install wyes, tees, and bends as shown on the Plans or as directed.
6. Tapered Pipe Inlets
Locate and install tapered pipe inlet end sections as shown on the Plans or as directed.
7. Elongation
Elongate metal pipe as shown on the Plans. Order the elongation of the vertical axis of the pipe to be done in
the shop.
Have the manufacturer ship metal pipe with wire ties in the pipe ends. Remove wire‐ties immediately after
completing the fill.
8. Flared End Sections
Use flared end sections on the inlet, outlet, or on both ends of storm drain pipe, according to Plan details.
9. Polyvinyl Chloride (PV) Profile Wall Drain Pipe
Section 550 – Storm Drain Pipe
Page 73
Install polyvinyl chloride (PVC) profile wall pipe according to ASTM D 2321. Use fittings and couplings that
comply with the joint performance criteria of AASHTO Standard Specifications for Highway Bridges, Division II.
Ensure that all joints are “soiltight” as stated in the AASHTO bridge specifications.
550.3.06 Quality Acceptance
Clean pipes and pipe‐arch culverts before final acceptance of the Work.
The Engineer may conduct video surveillance on storm drain (cross drain and longitudinal drain) installations
after all activities are complete that may damage the pipe, but before the placement of the base and paving
when applicable. If video surveillance shows problems such as pipe deformation, cracking, or joint separation,
the Contractor shall repair or replace these pipes at no cost to the Government.
Use a nine‐point mandrel to test a minimum of 25% of the installed length of smooth‐lined corrugated
polyethylene or PVC profile wall drain pipe for deformation (pieces will be selected by the Engineer). Use a
mandrel that has an effective diameter equal to 95% of the base inside diameter. Provide the Engineer with a
proving ring to verify the mandrel size. Mandrel testing shall not be paid for separately.
Ensure that smooth‐lined corrugated polyethylene or PVC profile wall drain pipe installations have a maximum
of 5% deflection when checked after completing all construction activities that may damage the pipe, but
before placing the base and paving when applicable. If mandrel testing reveals problems, the Engineer may
require that up to 100% of the storm drain installations be checked for deformation. Remove and replace pipe
with over 5% deflection at no cost to the Government.
550.3.07 Omitted
550.4 Measurement
A. Excavation and Backfill
Excavation and Backfill for Storm Drainage Pipe Installation shall not be measured separately for payment.
B. Flat Bottom and Circular Pipe (All Types)
The overall length of pipe installed, excluding tapered inlets, is measured in linear feet (meters), along the
central axis of the diameter of the pipe. Wyes, tees, and bends are included in this measurement.
C. Pipe‐Arches
The overall length of pipe‐arch installed is measured in linear feet (meters), along the bottom center line of the
pipe.
D. Multiple Installations
In multiple installations, each single line of culvert structure is measured separately.
E. Tapered Pipe Inlets
Tapered pipe inlet sections are measured as a unit; do not include them in the overall length of the pipe.
F. Flared‐End Sections
Section 550 – Storm Drain Pipe
Page 74
Flared‐end sections are measured separately by the unit and not included in the overall pipe length. G. Smooth‐
Flow Pipe
Smooth‐flow pipe is measured by the linear foot along the pipe invert.
550.4.01 Limits
Excavation and normal backfill are not measured for payment.
550.5 Payment
Pipe installations complete in place and accepted will be paid for at the Contract Pipe for each item.
This payment is full compensation for excavating, furnishing, and hauling materials; installing, cutting pipe
where necessary; repairing or replacing damaged sections; making necessary connections; strutting, elongating,
providing temporary drainage; joining an extension to an existing structure where required; and removing,
disposing of, or using excavated material as directed by the Engineer.
1. Smooth Flow Pipe
The quantity of each diameter and steel thickness of smooth flow pipe as measured will be paid for at the
Contract Unit Price per linear foot (meter) bid for the various sizes. Payment is full compensation for furnishing
labor, materials, tools, O‐ring mechanical joints, equipment, and incidentals to complete this Item, including
removing and disposing excavation material.
2. Flared‐End Sections
Flared‐end sections, measured as specified above, will be paid for at the Contract Unit Price for each section of
the specified size.
Payment will also include sawing, removing, and replacing existing pavement removed to install a new drainage
structure.
Payment will be made under:
Item No.
550 Storm drain pipe, RCP, 18 in Per linear foot
Item No.
550 Side drain pipe, BCCMP, 18 in Per linear foot
Item No.
550 Safety End Section, 18 in, Storm Drain Pipe Per each
Item No.
550
Safety End Section, 18 in, Side Drain Pipe Per each
Page 75
Section 603—Rip Rap
603.1 General Description
This work includes placing protective coverings of sand‐cement bag rip rap or stone rip rap.
When required, this work includes placing crushed stone filter material or plastic filter fabric beneath stone rip
rap on:
Fill slopes
Cut slopes
End rolls
Shoulders
Ditches
Stream banks
Channel banks
A. Bags for Sand‐Cement Bag Rip Rap
Use cotton, burlap, or fiber reinforced paper bags that can contain the sand‐cement mixture without leaking
during handling and placing. Do not use bags that previously held sugar or other material that will adversely
affect the sandcement mixture.
Ensure that the capacity is at least 0.75 ft³ (0.02 m³) but not greater than 2 ft³ (0.5 m³).
B. Stone Dumped Rip Rap
Stone dumped rip rap is designated on the Plans.
603.2.01 Delivery, Storage, and Handling General Provisions 101 through 150.
603.3 Construction Requirements
603.3.05 Construction
Construct this Work according to the following requirements:
A. Preparing the Foundations
Prepare the ground surface where the rip rap will be placed to conform with the correct lines and grades before
beginning the placement.
1. When filling depressions, compact the new material with hand or mechanical tampers.
Dispose of excess material by spreading it neatly within the right‐of‐way as an incidental part of the work.
2. Unless otherwise shown or provided below, begin placing the rip rap in a toe ditch constructed
in original ground around the toe of the fill or the cut slope.
Section 603—Rip Rap
Page 76
Ensure that the toe ditch is 2 ft (600 mm) deep in original ground and the side next to the fill or cut has the same
slope.
3. After placing the rip rap, backfill the toe ditch and spread the excess dirt neatly within the right‐
of‐way as an incidental part of the work.
4. When beginning rip rap in water or below normal water level, substitute an apron of rip rap for
the toe ditch.
Ensure that the width and thickness of this apron is as shown on the Plans or determined by the Engineer.
B. Placing Stone Rip Rap
Place rip rap to the limits shown on the Plans or as directed by the Engineer. Place and classify rip rap as follows:
1. Stone Plain Rip Rap
Dump and handle stone plain rip rap into place to form a compact layer to the design thickness.
Ensure that the thickness tolerance for the course is plus 12 in (300 mm) with no under‐tolerance. If the Plans
do not show a thickness, place stone rip rap to at least 12 in (300 mm) thick, but no greater than 2 ft (600 mm)
thick.
2. Stone Dumped Rip Rap
Dump stone dumped rip rap into place to form a uniform surface as thick as specified in the Plans.
a. Ensure that the thickness tolerance for the course is minus 6 in (150 mm) and plus 12 in (300
mm). If the Plans or Proposal do not specify a thickness, place the course to at least 2 ft (600 mm)
thick.
b. Recycled concrete that meets the requirements of Subsection 805.2.01 may be used instead of
stone when shown on the Plans or approved by the Engineer.
Use recycled concrete only when materials do not contain steel after processing.
NOTE: Do not use recycled concrete in aesthetically sensitive areas.
3. Stone Grouted Rip Rap
Place stone grouted rip rap according to specifications for stone plain rip rap and these guidelines: a. Prevent
earth from filling the spaces between the stones.
b. After placing the stone, fill the spaces between them with 1:3 grout composed of Portland
cement and sand mixed thoroughly with enough water to make a thick, creamy consistency.
c. Place the grout beginning at the toe. Finish it by sweeping with a stiff bristle broom.
d. After grouting, cover the rip rap and keep it wet for 5 days, or cover and keep wet for 24 hours
and then coat with white pigmented membrane curing compound.
C. Placing Filter
Section 603—Rip Rap
Page 77
Place woven plastic filter fabric under all rip rap. Follow these requirements for placing the filter fabric:
1. Prepare the surface to receive the fabric until it is smooth and free from obstructions,
depressions, and debris.
2. Place the fabric with the long dimension running up the slope. Minimize the number of overlaps.
3. Place the strips to provide a width of at least 1 ft (300 mm) of overlap for each joint.
4. Anchor the filter fabric in place with securing pins of the type recommended by the fabric
manufacturer. Place the pins on or within 3 in (75 mm) of the centerline of the overlap.
5. Place the fabric so that the upstream strip will overlap the downstream strip.
6. Loosely place the fabric to prevent stretching and tearing during stone placement.
Do not drop the stones more than 3 ft (1 m) during construction.
7. Always protect the fabric during construction from clogging due to clay, silts, chemicals, or other
contaminants.
8. Remove contaminated fabric or fabric damaged during installation or rip rap placement. Replace
with uncontaminated or undamaged fabric at no expense to the Government.
D. Placing Sand‐Cement Bag Rip Rap
Place rip rap to the limits shown on the Plans or as directed by the Engineer.
1. Proportioning Materials
Mix sand and Portland cement at the maximum ratio of 5:1 by weight.
a. Obtain a minimum compressive strength of 500 psi (3 MPa) in 7 days.
b. For sand‐cement bag rip rap, use enough water to make up the optimum moisture content of
the aggregate and cement as determined by AASHTO T 134.
c. When sand‐cement rip rap is to be prebagged, mix the sand cement dry. After placing each
course, wet the bags until the bags are wet enough for proper cement hydration.
2. Placement
Before placing sand‐cement bag rip rap, fill the bags full, but allow room to tie the bags.
a. Place the bagged rip rap by hand with the tied ends facing the same direction. Produce close,
broken joints.
b. Place header courses when directed by the Engineer or required by the Plans.
c. After placing the bags, ram or pack them against one another to produce the required thickness
and form a consolidated mass.
d. Do not allow the top of each bag to vary more than 3 in (75 mm) above or below the required
plane.
Section 603—Rip Rap
Page 78
E. Placing Stone Blanket Protection
Ensure that the stone blanket protection meets the materials Specifications for stone filter blanket as specified
in Subsection 603.2, “Materials,” except stone size No. 357 will be allowed instead of size No. 467.
Place stone blanket protection to the limits shown on the Plans, or as directed by the Engineer.
Uniformly place this material to the thickness shown on the Plans and to a thickness tolerance of 0.5 in (± 15
mm).
Do not use stone blanket protection on slopes steeper than two horizontal to one vertical or in areas highly
susceptible to erosion. Do not use plastic filter fabrics with stone blanket protection.
603.4 Measurement
This work is measured for payment in square yards (meters) of accepted material of the specified thickness.
Area measurements are made parallel to the surface on which the material is placed. Plastic filter fabric will be
measured as the area of rip rap placed and accepted. No separate measurement will be made for fabric overlap
joints, seams, or vertical sections at toe of slopes. No separate measurement is made for grout or cushioning
sand.
Plan dimensions are figured by the use of filled bags 12 by 18 by 6 in. (300 by 450 by 150 mm) thick.
When filled bags are less than Plan dimensions or are of varying lengths or width, Plan square yards (meters) will
be used to determine pay quantities, if overall dimensions are equal to or greater than those shown on the
Plans.
603.5 Payment
This work will be paid for at the Contract Price per square yard (meter) of material complete in place.
Payment will be made under:
Item No. 603 Stone dumped rip rap, Type 1, 24 in thick Per square yard
Page 79
Section 611—Adjusting to Grade of Miscellaneous Roadway Structures
611.1 General Description
This work includes relaying, reconstructing, resetting, adjusting to grade, capping minor structures, resetting
guard rail, or adjusting other miscellaneous roadway structures as specified in the Proposal or on the Plans.
611.3.05 Construction
A. Miscellaneous Roadway Items
Follow these procedures to construct miscellaneous roadway items:
1. Remove existing structures to be rebuilt according to Section 610.
2. Clean the material salvaged for use in the rebuilt structure and stockpile it in convenient places.
Protect it from damage until it is used.
3. Dispose of the portions of structures not suitable for reuse as provided in Section 610. Replace
them with suitable new material.
4. Relay or rebuild the structures according to the Specifications for new structures of the same
type.
5. Adjust to the required grade miscellaneous structures specified in the Proposal or on the Plans
by raising or lowering the upper portion of the fixture, including sleeve extensions, adjustable manhole
rings, gaskets, mastic, mortar, masonry, and other material.
6. Furnish materials such as mortar, sand‐cement grout, sand cushion, bituminous filler, brick,
castings, and other materials to excavate, trench, prepare earth foundation, backfill, and other work
necessary to complete the Item.
B. Capping an Existing Structure
When capping an existing structure requires removing adjacent existing pavement, sidewalk, curb, gutter, or
other improvement not otherwise affected by the work, follow these guidelines:
1. Remove the improvements to expose only the portion of the structure to be modified.
2. Replace the removed improvements to the Engineer’s satisfaction without additional
compensation.
3. Remove enough existing masonry to lower the top elevation to a point not less than the
thickness of the cap plus 3 ft (1 m) below subgrade elevation, unless otherwise indicated.
4. Cap the remaining portion of the structure with a fitted reinforced concrete cover constructed
to the general details shown on the Plans.
Grates, rings, plates, covers, hoods, or other castings or fittings removed while capping and not re‐used become
the property of the Government unless otherwise indicated on the Plans.
Section 611 — Adjusting to Grade of Miscellaneous Roadway Structures
Page 80
C. Resetting Guard Rail
When resetting the guard rail is specified in the Proposal:
1. Reset guard rail removed according to Section 610 where the Plan indicates and to the required
post spacing.
2. Furnish materials, including additional hardware, offset blocks, and posts.
3. Replace posts that do not conform to the Plans.
4. Follow the applicable provisions of Section 641.
D. Raising Manholes
When raising manholes:
1. Adjustments may be made by using adjustable extension rings that do not require removing the
existing manhole frame.
2. Ensure that the extension device locks to the existing frame and permits height and diameter
adjustment. The adjustable extension ring to be used shall have the Engineer’s prior approval.
3. Choose an extension ring compatible with the existing casting and cover. Ensure that the
adjustment range conforms to the finished pavement surface.
a. Use an adjustable extension ring made of materials that meet the requirements of Subsection
854.2.01 or are manufactured from ASTM A 36/A 36M steel and approved by the Engineer.
b. nsure that the extension ring and cover are machine ground to reduce contact irregularity.
Ensure that the grates are rattleproof.
c. Obtain the Engineer’s approval for the type of adjustable extension ring used.
E. Omitted
611.4 Measurement
Relaying, reconstructing, or adjusting to grade, capping minor structures, resetting guard rail, or adjusting other
miscellaneous roadway structures is measured to determine the unit or units of each type completed and
accepted.
Manhole tops to be raised or lowered 2 ft (600 mm) or less are considered “Adjust to Grade.”
Remove manholes to be raised more than 6 ft (1.8 m) as clearing and grubbing, and construct a new manhole in
its place according to Section 668.
611.5 Payment
Relaying, reconstructing, resetting, adjusting to grade, capping minor structures, resetting guard rail, or
adjusting other miscellaneous roadway structures will be paid for at the Contract Unit price. Payment is full
Section 611 — Adjusting to Grade of Miscellaneous Roadway Structures
Page 81
compensation for relaying, resetting, reconstructing, or adjusting to grade the structures as specified in this
Specification.
Excavation and backfill necessary for capping is considered incidental to the Item and is not paid for separately.
Tapping a new pipeline into an existing structure is not considered reconstruction of the existing structure.
Payment will be made under:
Item No. 611 Adjust sanitary sewer manhole to grade Per each
Item No. 611 Adjust water meter box to grade Per each
Page 82
Section 641—Guardrail
641.1 General Description
This work includes furnishing and erecting guardrail and appurtenances according to the Specifications.
Conform with the lines, grades, and locations shown on the Plans or as directed.
Place W‐beam, T‐beam, or “T” beam with modified offset block as shown on the Plans and in the Proposal.
Unless designated otherwise, references to guardrail shall mean W‐beam.
Unless provided for in the Plans, this work also includes:
Grading to provide the “T” distance shown on the standard behind the guardrail
Grading to construct shoulder flares for approved guardrail anchorage systems and widened shoulders
along guard rail runs according to Section 205 and Section 208
Furnishing and setting additional posts (all lengths) together with the necessary offset blocks and
hardware (when specified in the Plans or in the Proposal)
641.1.02 Related References
A. Standard Specifications Section 205—Roadway Excavation
Section 208—Embankments
Section 645—Repair of Galvanized Coatings
Section 700—Grassing
Section 859—Guard Rail Components
Section 870—Paint
641.2 Materials
A. Steel Guardrail
Use steel guard rail and steel posts unless specified otherwise on the Plans or in the Proposal.
B. Guardrail Auxiliary Items
Ensure that the guardrail includes auxiliary materials and Work to make connections and other guardrail or
structures required to complete the construction indicated on the Plans.
C. Offset Blocks
Except at locations approved by the Engineer, use plastic offset blocks according to Subsection 859.2.05 “Plastic
Offset Blocks” for “W” beam guardrail installation. Offset blocks for “T” beam guardrail installations shall be
plastic, or modified steel offset blocks per the Standard Plans including Construction Details and Section 859.
When approved by the Engineer, use treated wood offset blocks according to Subsection 859.2.04, “Wood
Section 641—Guardrail
Page 83
Guard Rail Posts and Offset Blocks.”only in isolated areas of “W” beam or “T”beam guardrail installations,
where standard size blocks would not provide a satisfactory fit.
Wood offset blocks and/or wood posts may be specified within the limits of an approved anchorage terminal.
Use only one type of offset block within continuous runs of guardrail except in transitions or where specified in
the Plan details.
Ensure that materials meet the requirements of these Specifications:
Material Section
Guardrail Elements and Fittings 859.2.01
Cable End Anchor Assembly 859.2.02
Steel Post and Offset Blocks 859.2.03
Wood Post and Offset Blocks 859.2.04
Plastic Offset Blocks 859.2.05
Galvanized Repair Compound 870.2.05
641.3 Construction Requirements
641.3.01 Omitted
641.3.02 Omitted
641.3.03 Omitted
641.3.04 Fabrication
A. Guard Rail Anchorages, Mounting Devices, and Brackets
Fabricate and install guardrail anchorages, mounting devices, brackets, and other appurtenances according to
the Plan details or as approved by the Engineer.
641.3.05 Construction A. Erection of Posts
1. Wood guardrail posts shall not be used at any location except as required for guardrail
anchorage.
2. Set the posts in post holes or drive them vertically at the positions, depth, spacing, and
alignment shown on the Plans.
3. Install posts for guard rail on bridges or other structures as detailed on the Plans.
Section 641—Guardrail
Page 84
4. Backfill post holes to the ground line with approved material tamped in place in layers of not
more than 4 in (100 mm) thick.
5. If posts are driven, protect the tops of the posts with a suitable driving mat or cap. Remove and
replace posts damaged during driving, at no additional cost.
6. Backfill the post holes that are drilled in rock as indicated on the Plans or directed by the
Engineer.
7. Remove and reset posts that are out of alignment or too low in grade. Do not cut off posts that
are too high; drive them to the proper elevation. Do not deviate more than 1/4 in (6 mm) vertical and
horizontal post alignment.
8. Fit the posts with an offset block according to this Specification and Plan details.
9. Set additional posts and appurtenances, when required, according to the requirements of this
Section and the Plan details.
10. When necessary to place posts in existing pavement, slope paving, etc., exercise extreme care
in the cutting process, protect the adjacent areas, and remove all loose material. Cut holes in the
existing paved area by drilling or sawing.
Replace the pavement material in kind to the full depth of the original pavement, as directed, after the post is
installed.
B. Erection of Rail
Erect the rails to attain a smooth, continuous rail line that conforms to the line and grade of the highway.
Determine the height of the rail from the dimensions shown on the Plans. Use bolts long enough to extend at
least 1/4 in (6 mm) beyond the nuts after they are firmly tightened.
Install reflectorized washers on guardrail and anchorages. Where double faced guardrail is located on the inside
shoulder of medians, install reflectorized washers only on the side which is nearest to traffic. In stall
reflectorized washers according to this Specification and Plan details.
C. Damaged Spelter Coating
Repair damaged spelter coating according to the requirements of Section 645.
D. Guardrail Anchorages
Guardrail Anchorage Type 12 shall be any guardrail terminal, designed for use with “W” beam guardrail
installations, which has been approved by the FHWA as meeting the requirements of the National Cooperative
Highway Research Report 350, Test Level 3 (NCHRP‐350, TL‐3). Where the anchorage is connected to “T” beam
guardrail installations, a transition is required as shown in the Standard details.
Construct Type 12 anchorages according to the manufacturer’s requirements except for the grading which will
be as shown in the Plans and as directed by the Engineer. Obtain copies of the manufacturer’s details and
installation instructions and provide copies of the same to the Engineer prior to the installation of the unit.
Provide a FHWA letter of approval forNCHRP‐350, TL‐3 compliance of the terminal to be used as Type 12
anchorage.
Section 641—Guardrail
Page 85
Yellow and black nose striping, as shown on the Plans will be required on all Type 12 anchorages.
641.3.06 Omitted
641.3.07 Omitted
641.4 Measurement
A. Guardrail
Guardrail of the type specified is measured in linear feet (meters), including terminal sections when installed.
Measurement does not include guardrail anchorage assembly.
When double faced guardrail of the type specified is installed, the single guardrail on each side of the posts is
not measured separately. Each single rail is a component part of the double faced guardrail installation.
B. Guardrail Anchorage Assembly
This Item is measured by the number of each type installed according to the details shown on the Plans.
C. Guardrail Posts
All lengths of guardrail posts when shown in the Plans or Proposal as a separate payment Item are measured by
the Unit.
641.4.01 Omitted
641.5 Payment
Guardrail, of the type specified, complete in place including posts, offset blocks, and hardware will be paid for
at the Contract Price per linear foot (meter).
Guardrail anchorage assembly will be paid for at the Contract Price per each assembly, complete in place.
All lengths of guardrail posts when shown in the Contract documents as a separate Pay Item will be paid for at
the Contract Unit Price. Payment is full compensation for furnishing the posts, offset block, hardware, and Work
to complete the Item.
For Projects that do not include grading as a Pay Item, payment for guardrail and guardrail anchorage systems
on shoulders includes:
Embankment material for shoulders as shown on the Standard Details or Plans
Compacting embankment material for shoulders to the approximate density of the surrounding soils
Removing existing vegetation and obstructions before placing the embankment
Grassing the reconstructed area according to Section 700
Payment will not be increased or decreased when wood offset blocks are added to or substituted for steel or
plastic offset blocks.
Payment will be made under:
Section 641—Guardrail
Page 86
Item No. 641 Guardrail, type W, incl posts Per linear foot
Item No. 641 Guardrail anchorage, type 6 Per each
Item No. 641 Guardrail anchorage, type 12 Per each
Page 87
Section 652—Painting Traffic Stripe
652.1 General Description
This work includes furnishing and applying reflectorized traffic line paint according to the Plans and these
Specifications.
This Item also includes applying words and symbols according to Plan details, Specifications, and the current
Manual on Uniform Traffic Control Devices.
652.1.01 Definitions
Painted Stripes: Solid or broken (skip) lines. The location and color are designated on the Plans.
Skip Traffic Stripes: Painted segments between unpainted gaps as specified on the Plans. The location and color
are designated on the Plans.
652.1.02 Related References
A. Standard Specifications
Section 656—Removal of Pavement Markings
Section 870—Paint
B. Referenced Documents
QPL 46
AASHTO M 247
652.1.03 Omitted
652.2 Materials
Ensure that materials for painting traffic stripe, words, and symbols meet the following requirements:
Material Section
Traffic Line Paint 5A and 5B 870.2.02.A.2 and 870.2.02.A.3
Glass Beads for Use in Luminous Traffic Lines AASHTO M 247 Type 1*
*In addition, meet the following requirements for glass beads:
Maximum quantity of angular particles is less than 1% by weight
Maximum quantity of particles with milkiness, scoring, or scratching is less than 2% by weight
Glass beads do not impart any noticeable hue to the paint film
Glass beads conforming to the following alternate gradation may be used provided that all other
requirements of AASHTO M 247 and this Specification are met.
Section 652— Painted Traffic Stripe
Page 88
Alternate Gradation
Sieve Size Percent Passing
No. 16 (1.190
mm)
99 ‐ 100
No. 20 (0.850
mm)
75 ‐ 95
No. 30 (0.600
mm)
55 – 85
No. 50 (0.300
mm)
10 – 35
No. 100 (0.150
mm)
0 ‐ 5
652.2.01 Omitted
652.3 Construction Requirements
652.3.01 Omitted
652.3.02 Equipment
A. Traveling Traffic Stripe Painter
Use a traffic stripe painter that can travel at a predetermined speed both uphill and downhill, applying paint
uniformly. Ensure that the painter feeds paint under pressure through nozzles spraying directly onto the
pavement.
Use a paint machine equipped with the following:
1. Three adjacent spray nozzles capable of simultaneously applying separate stripes, either solid or skip, in
any pattern.
2. Nozzles equipped with the following:
Cutoff valves for automatically applying broken or skip lines
A mechanical bead dispenser that operates simultaneously with the spray nozzle to uniformly
distribute beads at the specified rate
Line‐guides consisting of metallic shrouds or air blasts
3. Tanks with mechanical agitators
4. Small, portable applicators or other special equipment as needed
B. Hand Painting Equipment
Use brushes, templates, and guides when hand painting.
Section 652— Painted Traffic Stripe
Page 89
C. Cleaning Equipment
Use brushes, brooms, scrapers, grinders, high‐pressure water jets, or air blasters to remove dirt, dust, grease,
oil, and other foreign matter from painting surfaces without damaging the underlying pavement.
652.3.03 Preparation
Locate approved paint manufacturers on QPL 46.
Before starting each day’s work, thoroughly clean paint machine tanks, connections, and spray nozzles, using
the appropriate solvent.
Thoroughly mix traffic stripe paint in the shipping container before putting it into machine tanks.
Before painting, thoroughly clean pavement surfaces of dust, dirt, grease, oil, and all other foreign matter.
652.3.04 Omitted
652.3.05 Construction
A. Alignment
Ensure that the traffic stripe is the specified length, width, and placement. On sections where no previously
applied markings are present, ensure accurate stripe location by establishing control points at spaced intervals.
The Engineer will approve control points. B. Application
Apply traffic stripe paint by machine. If areas or markings are not adaptable to machine application, use hand
equipment.
1. Application Rate
All work will be subject to application rate checks for both paint and beads.
Apply 5 in (125 mm) wide traffic stripe at the following minimum rates:
a. Solid Traffic Stripe Paint: At least 25 gal/mile (58.8 L/km)
b. Skip Traffic Stripe Paint: At least 6.3 gal/mile (14.8 L/km)
NOTE: Change minimum rate proportionately for varying stripe widths.
2. Thickness
Maintain a 15 mils (0.38 mm) minimum wet film thickness for all painted areas.
3. Do not apply paint to areas of pavement when:
The surface is moist or covered with foreign matter.
Air temperature in the shade is below 40 °F (5 °C)
Wind causes dust to land on prepared areas or blows paint and beads around during application.
4. Apply a layer of glass beads immediately after laying the paint. Apply beads at a minimum rate
of 6 lbs to each gallon (700 grams to each liter) of paint.
Section 652— Painted Traffic Stripe
Page 90
C. Protective Measures
Protect newly applied paint as follows:
1. Traffic
Control and protect traffic with warning and directional signs during painting. Set up warning signs before
beginning each operation and place signs well ahead of the painting equipment. When necessary, use a pilot car
to protect both the traffic and the painting operation.
2. Fresh Paint
Protect the freshly painted stripe using cones or drums. Repair stripe damage or pavement smudges caused by
traffic.
D. Appearance and Tolerance of Variance
Continually deviating from stated dimensions is cause for stopping the work and removing the nonconforming
stripe. (See Section 656.) Adhere to the following measurements:
1. Width
Do not lay stripe less than the specified width. Do not lay stripe more than 1/2 in (13 mm) over the specified
width.
2. Length
Ensure that the 10 ft (3 m) painted skip stripe and the 30 ft (10 m) gap between painted segments vary no more
than ± 1 ft (300 mm) each.
3. Alignment
a. Ensure that the stripe does not deviate from the intended alignment by more than 1 in (25 m)
on tangents or curves of 1 degree or less.
b. Ensure that the stripe does not deviate by more than 2 in (50 mm) on curves exceeding 1
degree.
652.3.06 Quality Acceptance
Ensure that stripes and segments of stripes are clean‐cut and uniform. Markings that do not appear uniform or
satisfactory, either during the day or night, or do not meet Specifications, will be corrected at the Contractor’s
expense. Work will be subject to application rate checks for both paint and beads.
The following will be accepted:
Sections of painted stripe, words, and symbols that have dried so that paint will not be picked up or
marred by vehicle tires
Sections placed according to the Plans and Specifications
The Contractor will be relieved of responsibility for maintenance on accepted sections.
A. Correction of Alignment
Section 652— Painted Traffic Stripe
Page 91
When correcting a deviation that exceeds the permissible tolerance in alignment, do the following:
1. Remove the affected portion of stripe, plus an additional 25 ft (8 m) in each direction.
2. Paint a new stripe according to these Specifications.
Remove the stripe according to Section 656.
B. Removal of Excess Paint
Remove misted, dripped, or spattered paint to the Engineer’s satisfaction. Do not damage the underlying
pavement during removal.
Refer to the applicable portions of Section 656.
652.3.07 Omitted
652.4 Measurement
When traffic stripe is paid for by the square yard (meter), the number of square yards (meters) painted is
measured and the space between stripes is included in the overall measurement.
Linear measurements are made on the painted surface by an electronic measuring device attached to a vehicle.
On curves, chord measurements, not exceeding 100 linear feet (30 linear meters), are used.
Traffic stripe and markings, complete in place, are measured and accepted for payment as follows:
A. Solid Traffic Stripe
Solid traffic stripe is measured by the linear foot (meter), linear mile (kilometer), or square yard (meter). Breaks
or omissions in solid lines or stripes at street or road intersections are not measured.
B. Skip Traffic Stripe
Skip traffic stripe is measured by the gross linear foot (meter) or gross linear mile (kilometer). Unpainted spaces
between the stripes are included in the overall measurements if the Plan ratio of 1 to 3 remains uninterrupted.
Measurement begins and ends on a stripe.
C. Pavement Markings
Markings are words and symbols completed according to Plan dimensions. Markings are measured by the unit.
652.4.01 Omitted
652.5 Payment
Payment will be full compensation for the work under this Section, including the following:
Cleaning and preparing surfaces
Furnishing materials, including paints, beads, and thinners
Applying, curing, and protecting paints
Protecting traffic, including providing and placing necessary warning signs
Section 652— Painted Traffic Stripe
Page 92
Furnishing tools, machines, and other equipment necessary to complete the Item Payment will be made under:
Item No. 652 Solid traffic stripe, 5 in, yellow Lump Sum
Page 93
Section 653—Thermoplastic Traffic Stripe
653.1 General Description
This work includes furnishing and applying thermoplastic reflectorized pavement marking compound. Ensure
that markings conform to Plan details and locations, these Specifications, and the Manual on Uniform Traffic
Control Devices.
Thermoplastic traffic stripe consists of solid or broken (skip) lines, words, and symbols according to Plan color,
type, and location.
653.1.01 Definitions
Thermoplastic Marking Compound: A compound extruded or mechanically sprayed on the pavement that cools
to pavement temperature. When combined with glass spheres it produces a reflectorized pavement marking.
Short Lines: Crosswalks, stop bars, arrows, symbols, and crosshatching. Extrude short lines rather than spraying
them on. Unless otherwise specified, spray all other lines.
653.1.02 Related References
A. Standard Specifications
Section 652—Painting Traffic Stripe
B. Referenced Documents
QPL 46
Federal Test Method Standard 141, Method 4252
ASTM D 1155
ASTM D 620 ASTM D 570 ASTM D 256
ASTM D 2240
ASTM E 28
ASTM 121
653.1.03 Submittals
Ensure that the producers of the thermoplastic compound and glass spheres furnish to the Engineer copies of
certified test reports showing results of all tests specified in this Section. Also ensure that producers certify that
the materials meet the other requirements of this Section by submitting copies of certification at the time of
sampling. Final Acceptance, however, will be based on satisfactory test results from samples obtained by the
Engineer before delivery.
653.2 Materials
A. General Characteristics of Thermoplastic
Section 652— Painted Traffic Stripe
Page 94
1. Deterioration
Use thermoplastic material with the following characteristics: a. Does not deteriorate upon contact with:
Pavement materials
Petroleum droppings from traffic
Chemicals, such as sodium chloride or calcium chloride, used to prevent formation of ice on roadways or streets
b. Does not scorch, discolor, or deteriorate if kept at the manufacturer‘s recommended application
temperature, or at least 375 °F (190 °C), for up to 4 hours.
c. Has a temperature versus viscosity characteristic that remains constant from batch to batch
through four reheatings.
Thermoplastic Traffic Stripe
2. Fumes
Use material that in the plastic state does not give off fumes that are toxic or harmful to persons or property.
B. Detailed Characteristics of Thermoplastic
1. Material Composition
Use material binder with the following characteristics:
A mixture of synthetic resins, with at least one resin that is solid at room temperature, and high boiling
point plasticizers
A total binder content of 18 percent to 35 percent by weight
A pigmented binder that is well‐dispersed and free of dirt, foreign objects, or ingredients that cause
bleeding, staining, or discoloration
The binder shall be Type A—alkyd. Ensure that at least 33% of the binder composition or at least 8% by weight
of the entire material formulation is a maleic‐modified glycerol ester of resin. Ensure that the finished
thermoplastic pavement marking material is not adversely altered by contact with oily pavement materials or by
contact from oil dropping onto the pavement surface from traffic. Ensure that the filler has the following
characteristics:
White calcium carbonate or equivalent
Compressive strength of 5,000 psi (34.5 MPa)
2. Suitability for Markings
Use thermoplastic material that is especially compounded for traffic markings and has the following
characteristics:
Prevents markings from smearing or spreading under normal traffic conditions at temperatures below
120 °F (49 °C)
Gives a uniform cross section, with pigment evenly dispersed throughout the material
Has a uniform material density and character throughout its thickness
Allows the stripe to maintain its original dimensions and placement
Section 652— Painted Traffic Stripe
Page 95
Ensures that the exposed surface is free from tack and is not slippery when wet
Does not lift from the pavement in freezing weather
Has cold ductility properties that permit normal movement with the road surface without chipping or
cracking
3. Drying Time
When applied at a temperature range of 400 °F to 425 °F (204 oC – 218 oC) and a thickness of 1/8 in. to 3/16 in.
(3 mm to 5 mm), the material shall set to bear traffic in a maximum of 2 minutes when the air temperature is 50
°F ± 3 °F (10 oC ± 2 oC) and shall set to bear traffic in a maximum of 10 minutes when the air temperature is 90
°F ± 3 °F (32 oC ± 2 oC).
4. Reflectorization
Ensure that during manufacturing, reflectorizing glass spheres were mixed into the compound to the following
specifications:
At least 16 percent by weight using glass spheres with a minimum refractive index of 1.65
At least 25 percent by weight using glass spheres with a minimum refractive index of 1.50
C. Physical Requirements of Thermoplastic
1. Color
Confirm the color of thermoplastic as follows:
a. White thermoplastic material contains at least 8 percent by weight titanium dioxide that meets the
requirements of ASTM D 476, Type II, Rutile. The white thermoplastic material shall be pure white and free from
dirt or tint.
The material, when compared to the magnesium oxide standard using a standard color spectrophotometer
according to ASTM D 4960, shall meet the following:
Scale Definition Magnesium Oxide Standard Sample
Rd Reflectance 100 75 min.
Thermoplastic Traffic Stripe
a Redness‐Greenness 0 ‐5 to + 5
b Yellowness‐Blueness 0 ‐10 to + 10
Compare yellow material to match Federal Test Standard Number 595, Color 13538.
2. Color Retention
Use thermoplastic stripe tested for color retention as follows:
Section 652— Painted Traffic Stripe
Page 96
a. Test specimens prepared from samples submitted according to ASTM D 620 by the Government
Inspector.
b. Use an ultraviolet light source as specified in the test procedure, or use a 275 watt sunlamp with
a built‐in reflector.
c. Ensure that after 100 hours of exposure to the light source, the test specimens show no color
change when compared to an unexposed specimen.
3. Water Absorption
Ensure that materials have no more than 0.5 percent by weight of retained water when tested by ASTM D 570,
procedure (a).
4. Softening Point
Ensure that materials have a softening point of at least 175 °F (79 °C) as determined by ASTM E 28.
5. Specific Gravity
Ensure that the specific gravity of the thermoplastic compound at 77 °F (25 °C) is between 1.9 to 2.5.
6. Impact Resistance
Use material with an impact resistance of at least 10 in‐lbs at 77 °F (1.13 N∙m at 25 °C), tested as follows: a.
Heat for 4 hours at 400 °F (204 °C).
b. Cast into bars of 1 in² (625 mm²) cross sectional area, 3 in (75 mm) long.
c. Place with 1 in (25 mm) extending above the vise in a cantilever beam (Izod type) tester using
the 25 in‐lbs (2.82 N∙m) scale. This instrument is described in ASTM D 256.
7. Indentation Resistance
Measure the hardness by a Shore Durometer, Type A2, as described in ASTM D 2240. Maintain the temperature
of the Durometer, 4.4 lb. (2 kg) load and the specimen at 115 °F (45 oC). Apply the Durometer and 4.4 lb. (2 kg)
load to the specimen and the reading shall be between 50 to 75 units, after 15 seconds.
8. Low Temperature Stress Resistance
a. Furnish sample test blocks as follows:
1) Coat the samples using the same method as the planned installation of the compound.
2) Coat the samples with at least 32 in² (206 mm2) of the compound.
b. Have the samples tested as follows:
1) Immerse a sample in cold water for one hour.
2) Immediately place the sample in a freezer chest or other insulated cold compartment
and maintain at a temperature of –20 °F (–29 ºC) for 24 hours.
3) After 24 hours, remove the sample and bring it to normal room temperature.
Section 652— Painted Traffic Stripe
Page 97
Following the test, confirm that the sample does not crack, flake, or fail to adhere to the substrate.
9. Reheating
Ensure that the compound does not break down, deteriorate, scorch, or discolor if held for 6 hours at the plastic
temperature of 425 °F (218 °C); or if reheated up to the plastic temperature 4 times.
10. Abrasion Resistance
Have the material tested for abrasion resistance as follows:
a. Ensure that the maximum loss of the material does not exceed 0.4 grams when subjected to 200
revolutions on a Taber Abraser at 77 °F (25 °C), using H‐22 Calibrade wheels that are weighted to
500 grams.
b. Keep the wearing surface wet with distilled water throughout the test.
Thermoplastic Traffic Stripe
c. Prepare the panel by forming a representative lot of material at a thickness of 0.125 in. (3.18 mm) on a 4 in
(100 mm) square steel plate with a thickness of 0.050 ± 0.001 in (1.27 mm ± 0.03 mm), on which a primer has
been previously applied. 11. Yellowness Index
The white thermoplastic material shall not exceed a yellowness index of 0.12 according to AASHTO T 250.
12. Flowability
After heating the thermoplastic material for 240 ± 5 minutes at 425 °F ± 3 °F (218 oC ± 2 oC) and testing the
flowability, ensure that the white thermoplastic has a maximum of 21 percent residue according to AASHTO T
250.
13. Flowability‐Extended Heating
After heating the thermoplastic material for 8.0 ± 0.5 hours at 425 °F ± 3 °F (218 oC ± 2 oC), while stirring the last
6 hours and testing for flowability, ensure that the thermoplastic has a maximum percent residue of 28
according to AASHTO T 250.
14. Storage Life
The material shall meet the requirements of this specification for 1 year. Ensure that the thermoplastic melts
uniformly with no evidence of skins or unmelted particles during the 1‐year period.
D. Physical Requirements of Glass Spheres
1. Premixed Glass Spheres
Ensure that the compound has been manufactured with glass spheres in the proportion specified in
Subsec on 653.2.B.4, ―Reflectoriza on.‖ The glass spheres contained in the material shall meet the following
requirements:
a. Index of Refraction. Determine the index of refraction of the premixed glass spheres by the
liquid immersion method at 77 °F (25 °C).
Section 652— Painted Traffic Stripe
Page 98
b. Roundness. Ensure that the minimum percentages of premixed glass spheres are true spheres
according to the following table:
Percent of Premixed Glass Spheres That are True Spheres (when tested according to ASTM D 1155)
Minimum Index of Refraction Percent of Overall Beads Percent of Beads Retained on
any Sieve
1.65 At least 75% At least 70%
1.50 At least 70% At least 60%
c. Imperfections. Ensure that no more than 5 percent of the spheres show air inclusions, bubbles,
lap lines, chill wrinkles, or other imperfections when viewed through a 60‐power microscope in the
refractive index liquid.
d. Foreign Matter. Ensure that the quantity of foreign matter does not exceed 1 percent.
e. Gradation. Have the beads tested using ASTM: D 1214 to ensure they have the following
gradations:
U.S. Sieve Standard Sieve Size Percent Passing
No. 16 (1.18 mm) 100
No. 30 (600 µm*) 60 to 90
No. 50 (300 µm) 15 to 40
No. 80 (180 µm) 0 to 10
No. 100 (150 µm) 0 to 5
*µ = micro meter
f. Chemical Resistance. Use material manufactured with glass spheres that withstand immersion
in water and acids without corroding or etching, and withstand sulfides without darkening or
decomposing.
Have the chemical resistance tested by placing a 3 g to 5 g sample in each of three glass beakers or porcelain
dishes and immersing as follows:
Cover the first with distilled water.
Cover the second with a 3N solution of sulfuric acid.
Cover the third with a solution of 50 percent sodium sulfide, 48 percent distilled water, and 2 percent
Aerosol 1B or similar wetting agent.
Section 652— Painted Traffic Stripe
Page 99
Ensure that after one hour no darkening, hazing, or other evidence of instability is evident when examined
microscopically.
2. Drop‐On Glass Spheres
Ensure that these spheres meet the requirements of Subsection 652.2.
E. Requirements of Sealing Primer
Place the particular type of two‐part epoxy binder‐sealer at the application rate as recommended in writing by
the thermoplastic material manufacturer.
653.2.01 Delivery, Storage, and Handling
Use material delivered in 50 lb (22.7 kg) unit cardboard containers or bags strong enough for normal handling
during shipment and on‐the‐job transportation without loss of material.
Ensure that each unit container is clearly marked to indicate the following:
Color of the material
Process batch number or similar manufacturer‘s identification
Manufacturer‘s name
Address of the plant
Date of manufacture
653.3 Construction Requirements
653.3.01 Personnel
General Provisions 101 through 150.
653.3.02 Equipment
Depending on the marking required, use hand equipment or truck‐mounted application units on roadway
installations.
A. Spray Application Machine
Ensure that each spray application machine is equipped with the following features:
Parts continuously mix and agitate the material.
Truck‐mounted units for lane, edge, and center lines can operate at a minimum of 5 mph (8 kph) while
installing striping.
Conveying parts between the main material reservoir and the shaping die or gun prevent accumulation
and clogging.
Parts that contact the material are easily accessible and exposable for cleaning and maintenance.
Mixing and conveying parts, including the shaping die or gun, maintain the material at the plastic
temperature with heat transfer oil or electrical element controlled heat. Do not use an external source
of direct heat.
Parts provide continuously uniform stripe dimensions.
Section 652— Painted Traffic Stripe
Page 100
Applicator cleanly and squarely cuts off stripe ends and applies skip lines. Do not use pans, aprons, or
similar appliances that the die overruns.
Parts produce varying widths of traffic markings.
Applicator is mobile and maneuverable enough to follow straight lines and make normal curves in a true
arc.
B. Automatic Bead Dispenser
Apply glass spheres to the surface of the completed stripe using a dispenser attached to the striping machine to
automatically dispense the beads instantaneously upon the installed line. Synchronize the glass sphere
dispenser cutoff with the automatic cutoff of the thermoplastic material.
Thermoplastic Traffic Stripe
C. Special Kettles
Use special kettles for melting and heating the thermoplastic material. Kettles equipped with automatic
thermostatic control devices provide positive temperature control and prevent overheating. Ensure that the
applicator and kettles are equipped and arranged according to the requirements of the National Fire
Underwriters.
D. Hand Equipment
Use hand equipment for projects with small quantities of lane lines, edge lines, and center lines, or for
conditions that require the equipment. Use hand equipment approved by the Engineer.
Ensure that hand equipment can hold 150 lbs (68 kg) of molten material and is maneuverable to install
crosswalks, arrows, legends, lane, edge, and center lines.
E. Auxiliary Vehicles
Supply the necessary auxiliary vehicles for the operation.
653.3.03 Omitted
653.3.04 Omitted
653.3.05 Construction
A. General Application
Thoroughly clean pavement areas to be striped. Use hand brooms, rotary brooms, air blasts, scrapers, or other
approved methods that leave the pavement surface clean and undamaged. Take care to remove all vegetation
and road film from the striping area. All new Portland Cement Concrete pavement surfaces shall be
mechanically wire brushed or abrasive cleaned to remove all laitance and curing compound before being
striped.
Lay stripe with continuous uniform dimensions.
Apply the type of stripe at each location according to the Plans, using one of the following methods:
Spray techniques
Section 652— Painted Traffic Stripe
Page 101
Extrusion methods wherein one side of the shaping die is the pavement, and the other three sides are
contained by or are part of the suitable equipment to heat and control the flow of material.
1. Temperature
Apply thermoplastic traffic stripe only when the pavement temperature in the shade is above 40 °F (4 °C).
To ensure optimum adhesion, install the thermoplastic material in a melted state at the manufacturer‘s
recommended temperature but not at less than 375 °F (190 °C).
2. Moisture
Do not apply when the surface is moist. When directed by the Engineer, perform a moisture test on the Portland
cement concrete pavement surface. Perform the test as follows:
a. Place approximately 1 yd2 (1m2) of roofing felt on the pavement surface.
b. Pour approximately 1/2 gallon (2 L)of molten thermoplastic onto the roofing felt.
c. After 2 minutes, lift the roofing felt and inspect to see if moisture is present on the pavement
surface or underside of the roofing felt.
d. If moisture is present, do not proceed with the striping operation until the surface has dried
sufficiently to be moisture free.
3. Binder‐Sealer
To ensure optimum adhesion, apply a binder‐sealer material before installing the thermoplastic in each of the
following cases:
Extruded thermoplastic
Where directed by the Engineer for sprayed thermoplastic
Old asphaltic concrete pavements with exposed aggregates
Portland cement concrete pavements as directed by the Engineer
Ensure that the binder‐sealer material forms a continuous film that mechanically adheres to the pavement and
dries rapidly. Use a binder‐sealer currently in use and recommended by the thermoplastic material
manufacturer according to QPL 46.
To ensure optimum adhesion, apply a two‐part epoxy binder‐sealer on all Portland cement concrete pavements
for either sprayed or extruded thermoplastic material.
Apply the epoxy binder‐sealer immediately in advance of, but concurrent with, the application of the
thermoplastic material. Apply in a continuous film over the pavement surface.
4. Bonding to Old Stripe
The old stripe may be renewed by overlaying with new material. Ensure the new material bonds to the old line
without splitting or cracking.
5. Offset from Construction Joints
Off‐set longitudinal lines at least 2 in (50 mm) from construction joints of Portland cement concrete pavements.
Section 652— Painted Traffic Stripe
Page 102
6. Crosswalks, Stop Bars, and Symbols
Make crosswalks, stop bars, and symbols at least 3/32 in (2.4 mm) thick at the edges and no more than 3/16 in
(4.8 mm) thick at the center.
7. Film Thickness
a. Maintain the following minimum average film thicknesses on all open graded asphalt concrete friction
courses:
0.120 in (3.0 mm)* for lane lines
0.090 in (2.3 mm)* for edge lines
0.150 in (3.8 mm)* for gore area lines
b. Maintain the following minimum average film thicknesses on all other pavement types:
0.090 in 2.3 mm)* for lane lines
0.060 in (1.5 mm)* for edge lines
0.120 in (3.0 mm)* for gore area lines
(See below for ‗*‘ reference.)
Compute the minimums by the amount of material used each day, as follows:
(For 5 in wide stripe)
* Average Film Thickness (in) = [(lbs used) (total linear feet )] x 0.236
(For 125 mm wide stripe)
*Average Film Thickness (mm) = [(kg used) (total linear meters )] x 4.0
(For 10 in wide stripe)
* Average Film Thickness (in) = [(lbs used) (total linear feet )] x 0.118
(For 250 mm wide stripe)
* Average Film Thickness (mm) = [(kg used) (total linear meters )] x 2.0
8. Glass Spheres
a. Apply glass spheres to installed stripe surface at a minimum rate of 14 lbs of spheres to each
100 square feet ((700 g/m2) of thermoplastic material.
b. Apply the glass sphere top‐coating with a pressure‐type gun specifically designed for applying
glass spheres that will embed at least one‐half of the sphere‘s diameter into the thermoplastic
immediately after the material has been applied to the pavement.
B. Removing Existing Stripe
Remove existing stripe according to Section 656.
Section 652— Painted Traffic Stripe
Page 103
Remove 100 percent of existing traffic stripe from:
Portland cement concrete pavement where the new stripe will be placed at the same location as the existing
marking
Pavement where the new stripe will be placed at a different location from the existing markings
C. Tolerance and Appearance
No traffic stripe shall be less than the specified width and shall not exceed the specified width by more than 1/2
in (13mm). The length of the 10 ft (3 m) segment for skip stripe and the 30 ft (9 m) gap between segments may
vary plus or minus 1 ft (300 mm). The alignment of the stripe shall not deviate from the intended alignment by
more than 1 in (25 mm) on tangents and on curves up to and including 1 degree (radius of 1745 m or greater).
On curves exceeding 1 degree (radius less than 1745 m), the alignment of the stripe shall not deviate from the
intended alignment by more than 2 in (50 mm).
Stop work when deviation exceeds the above dimensions, and remove the nonconforming stripe.
653.3.06 Quality Acceptance
Segments of the thermoplastic traffic stripe that have been placed according to the Plans and Specifications may
be accepted 30 days after the required work is complete in that segment.
If thermoplastic traffic stripe fails to meet Plan details or Specifications or deviates from stated dimensions,
correct it at no additional cost to the Government. If removal of pavement markings is necessary, perform it
according to Section 656 and place it according to this Specification. No additional payment will be made for
removal and replacement of unsatisfactory striping.
653.3.07 Contractor Warranty and Maintenance
After segments are accepted, the Contractor will be relieved of maintenance on those segments.
653.4 Measurement
When stripe will be paid for by the square yard (meter), the actual number of square yards (meters) painted will
be measured. The space between the stripes will be included in the overall measurement.
Linear measurements may be made by electronic measuring devices attached to a vehicle.
Thermoplastic traffic stripe, complete in place and accepted, is measured as follows:
A. Solid Traffic Stripe
Stripe is measured by the linear foot (meter), linear mile (kilometer), or square yard (meter). Breaks or
omissions in solid lines or stripes at street or road intersections are not measured for payment.
B. Skip Traffic Stripe
Skip stripe is measured by the gross linear mile (kilometer) as specified. The unpainted space between the
painted stripes is included in the overall measurement if the Plan ratio of one to three (10 ft [3 m] segment and
30 ft [9 m] gap or other patterns as designated on the Plans) remains uninterrupted. Measurement begins and
ends on a stripe.
Section 652— Painted Traffic Stripe
Page 104
C. Words and Symbols
Each word or symbol complete according to Plan dimensions is measured by the Unit.
653.4.01 Omitted
653.5 Payment
Payment is full compensation for the Work under this section, including:
Cleaning and preparing surfaces
Furnishing all materials
Applying, curing, and protecting stripe
Protecting traffic, including providing necessary warning signs
Furnishing tools, machines, and other equipment necessary to complete the Item
Measurement and payment for removing pavement markings will be according to Section 656 when shown in
the Proposal as a payment Item. Otherwise, removal will not be paid for separately, but will be included in the
payment for other Work under this section.
Payment will be made under:
Item No. 653 Thermoplastic traffic stripe Lump Sum
Page 105
Section 668—Miscellaneous Drainage Structures
668.1 General Description
This work includes constructing catch basins, drop inlets, manholes, junction boxes, spring boxes, drain inlets,
special inlets with safety grates, and vertical tee sections.
Construct according to these Specifications and the lines and grades shown on the Plans, or as established by
the Engineer.
668.1.01 Omitted
668.1.02 Related References
A. Standard Specifications
Section 207—Excavation and Backfill for Minor Structures
Section 500—Concrete Structures
Section 607—Rubble Masonry
Section 608—Brick Masonry
Section 801—Fine Aggregate
Section 830—Portland Cement
Section 834—Masonry Materials
Section 843—Concrete Pipe
Section 853—Reinforcement and Tensioning Steel
Section 854—Castings and Forgings
Section 866—Precast Concrete Catch Basin, Drop Inlet, and Manhole Units
B. Omitted
668.1.03 Omitted
668.2 Materials
The structures in this section may be constructed of brick, cast‐in‐place concrete, or pre‐cast concrete, unless
the Plans or Proposal specifies a specific type of construction.
Use rubble masonry only when specified on the Plans. Ensure that materials meet the following specifications:
Material Section
Class “A” or “B” Concrete 500
Section 668—Miscellaneous Drainage Structures
Page 106
Sand for Bedding Material 801.2.01
Fine Aggregate for Mortar 801.2.02
Portland Cement 830.2.01
Brick 834
Masonry Stone 834
Mortar and Grout 834
Nonreinforced Concrete Pipe 843
Steel Bars for Reinforcement 853.2.01
Material Section
Gray Iron Castings 854.2.01
Precast Reinforced Concrete Catch Basin, Drop Inlet, and
Manhole Units
866
Ensure that the materials for fabricating special inlets and their safety grates are according to Plan details.
Construct the following manholes and drainage structures from pre‐cast or cast‐in‐place concrete:
Structures within the backfill limits of mechanically stabilized embankment retaining walls Structures
within 5 ft (1.5 m) of the wall foundation’s front.
668.2.01 Delivery, Storage, and Handling General Provisions 101 through 150.
668.3 Construction Requirements
668.3.01 Omitted.
668.3.02 Omitted
668.3.03 Omitted
668.3.04 Omitted
668.3.05 Construction
A. Excavation and Backfill
Excavate and prepare foundations for the structures included in this section; place pipe through the structures
according to Section 207.
B. Concrete
Section 668—Miscellaneous Drainage Structures
Page 107
Concrete units may be either poured‐in‐place or precast. Construct units as follows:
1. Poured‐in‐Place Units
The throat or other nonreinforced portions of catch basins may be Class B concrete. Use Class A concrete for the
top slab. Construct units according to Section 500.
2. Pre‐Cast Reinforced Concrete Units
Construct pre‐cast reinforced concrete units as follows:
a. Holes for Pipe
Cast each unit with the number and dimensions of pipe holes necessary to incorporate the unit into the
drainage system according to Plan details.
Installation conditions may require additional pipe for which no holes have been cast. If so, make the holes and
repair or replace, to the Engineer’s satisfaction, pipe damaged during the process.
b. Pipe Connections
Use mortar or Class A concrete to connect pipe to units.
c. Installation of Pre‐cast Concrete
1) Pre‐cast Reinforced Units: Set these units to within 1/2 in (± 13 mm) of grade on a bed
of compacted sand 2 in to 3 in (50 mm to 75 mm) thick.
2) Sectional Precast Reinforced Units: When using these units to build‐up extra‐depth
catch basins or drop inlets, fill the joints between sections with mortar and wipe smooth.
C. Brick Masonry
Construct brick masonry structures according to Section 608.
D. Mortar Rubble Masonry
Construct rubble masonry structures according to Section 607.
E. Castings
Hold frame castings securely in place to proper line and grade. Make castings an integral part of the complete
structure. After completion, ensure that castings subject to traffic use are firm and stable under traffic.
F. Maintenance
Thoroughly clean fallen masonry, silt, debris, and other foreign matter from structures. G. Safety Grates
Fabricate safety grates according to Plan details.
H. Sanitary Sewer Manholes
Ensure that sanitary and combination sanitary and storm sewer manholes conform to the following
requirements and the related Specifications.
Section 668—Miscellaneous Drainage Structures
Page 108
1. Form Invert Channels
Shape invert channels to the lines and grades shown on the Plans, or as established by the Engineer. Ensure that
channel surfaces are smooth.
Form invert channels by one of the following methods:
Directly form the invert channel in the concrete base of the manhole.
Construct the invert channel of brick and mortar.
Lay half‐ round tile in the concrete base of the manhole.
Lay round sewer pipe through the manhole and cut out the top half of the pipe after the concrete base has set.
Do not use this method if the Plans provide for an offset drop in the invert.
2. Plaster Outside Walls
Plaster outside walls as follows:
a. Saturate the outside wall of each brick manhole with water.
b. Plaster the wall smooth with a mortar coat at least 1/2 in (13 mm) thick. Manufacture the
mortar according to Section 834 with the following exceptions:
Manufacture the mortar with one part cement to two parts mortar sand.
Do not add hydrated lime.
3. Connections to Manholes
Complete manhole connections to the Engineer’s satisfaction and as follows:
a. Carefully connect existing sewer lines to new manholes to prevent infiltration of foreign
substances.
b. Construct manholes in or adjacent to existing sewer lines according to Section 660 to maintain
continuous sewage flow in existing lines.
668.3.06 Quality Acceptance
General Provisions 101 through 150.
668.3.07 Omitted
668.4 Measurement
Catch basins, drop inlets, manholes, junction boxes, drain inlets, special inlets, and safety grates, complete in
place and accepted, are measured for payment according to the following:
A. Catch Basins and Drop Inlets
Each catch basin or drop inlet is grouped for measurement as follows:
Group 1: Structures connected to pipe 36 in (900 mm) or less in diameter, regardless of the pipe skew
Section 668—Miscellaneous Drainage Structures
Page 109
Group 2: Structures connected to pipe over 36 in (900 mm) diameter regardless of the pipe skew Catch
basins or drop inlets, complete in place and accepted, are measured by the unit.
B. Manholes
Manholes are measured for payment as follows:
1. Sanitary and Storm Sewer Manholes
Sanitary sewer manholes and storm sewer manholes are measured separately and divided into two types:
Type 1: Structures connected to pipe 42 in (1050 mm) or less in diameter regardless of the pipe skew
Type 2: Structures connected to pipe 48 in to 84 in (1200 mm to 2100 mm) diameter regardless of the
pipe skew
C. Junction Boxes, Spring Boxes, and Drain Inlets
Junction boxes, spring boxes, and drain inlets are measured by the unit.
1. Each junction box will be complete according to Plan details.
2. Each drain inlet will consist of a pipe elbow or tee, concrete collar, and casting of the required
diameter.
3. Each spring box will be complete according to Plan details.
D. Omitted
E. Omitted
F. Omitted
668.4.01 Omitted
668.5 Payment
Payment for the various structures under this Section will be made as follows:
A. Catch Basins and Drop Inlets
Catch basins or drop inlets will be paid for at the Contract Price per each.
Depth in excess of 6 ft (2 m) will be paid for at the Contract Price per linear foot (meter).
Payment is full compensation for the following:
Furnishing castings
Making pipe connections regardless of skew
Providing materials, making forms, and disposing of surplus material
B. Manholes
Sanitary sewer and storm sewer manholes, complete in place, will be paid for at the Contract Price per each.
Section 668—Miscellaneous Drainage Structures
Page 110
Manhole additional depth of the appropriate class will be paid for at the Contract Price per linear foot (meter).
Payment is full compensation for the following:
Furnishing castings, fittings, and other appurtenances called for on the Plans to complete the Item
Making pipe connections regardless of skew
Providing materials, making forms, and disposing of surplus material
NOTE: No additional payment will be made for connecting manholes to existing or new sewer lines. Include
costs related to connections in the Contract Price for the structure.
C. Junction Boxes, Spring Boxes, and Drain Inlets
Junction boxes, spring boxes, or drain inlets will be paid for at the Contract Price per each. Payment is full
compensation for the following:
Furnishing castings, fittings, and other appurtenances called for on the Plans to complete the Item
Making pipe connections regardless of skew
Providing materials, making forms, and disposing of surplus material
D. Pipe
Pipe entering or exiting catch basins, drop inlets, manholes, junction boxes, spring boxes, or drain inlets, will be
paid for under the section of the Specifications governing the pipe.
E. Sand Bedding Material for Precast Structures
No separate payment will be made for this material. Its cost is included in the Contract Price for the structure
under which it is used.
F. Excavation and Normal Backfill
No separate payment will be made for excavation and normal backfill. Their cost is included in the Contract Price
for the structure being excavated.
G. Omitted
H. Omitted
Miscellaneous Drainage Structures
I. Omitted
Payment will be made under:
Item No. 668 Catch basin, group 1 Per each
Item No. 668 Drop inlet, group 1 Per each
Page 111
Section 700—Grassing
700.1 General Description
This work includes preparing the ground, furnishing, planting, seeding, fertilizing, sodding, and
mulching disturbed areas within the Right‐of‐Way limits and easement areas adjacent to the
right‐of‐way as shown on the Plans except as designated by the Engineer.
700.1.01 Omitted
700.1.02 Related References
A. Standard Specifications
Section 160—Reclamation of Material Pits and Waste Areas
Section 163—Miscellaneous Erosion Control Items
Section 718—Wood Fiber
Section 822—Emulsified Asphalt
Section 882—Lime
Section 890—Seed and Sod
Section 891—Fertilizers
Section 893—Miscellaneous Planting Materials
B. Referenced Documents
QPL 33
700.1.03 Omitted
700.2 Materials
Use materials that meet the requirements of the following Specifications:
Material Section
Wood Fiber Mulch 718.2
Emulsified Asphalt 822
Agricultural Lime 882.2.01
Seed 890.2.01
Section 700 - Grassing
Page 112
Sod 890.2.02
Fertilizer 891.2.01
Plant Topsoil 893.2.01
Mulch 893.2.02
Inoculants 893.2.04
Tackifiers QPL 33
A. Seeds
Whenever seeds are specified by their common names, use the strains indicated by their
botanical names.
B. Water
Obtain the water for grassing from an approved source. Use water free of harmful chemicals,
acids, alkalies, and other substances that may harm plant growth or emit odors. Do not use
salt or brackish water.
C. Asphalt
Secure the mulch with asphalt made of a homogenous emulsification of a refined petroleum.
Ensure that the asphalt can be sprayed on with or without diluting with water.
Use suitable asphalt free of petroleum solvents or other diluting agents that may harm plant
growth. Use asphalt according to Section 822. Do not use asphalt that separates after freezing
or from any other cause.
D. Fertilizer Mixed Grade
Select fertilizer mixed grade such as 10‐10‐10, 6‐12‐12, 5‐10‐15, or other analysis within the
following limits:
Nitrogen 5 to 10 percent
Phosphorus 10 to 15 percent
Potassium 10 to 15 percent
If using mixed grade fertilizer for hydroseeding, ensure that it has the following analysis:
Nitrogen 5 to 19 percent
Phosphorus 10 to 19 percent
Potassium 10 to 19 percent
E. Mulch
Section 700 - Grassing
Page 113
Use straw or hay mulch according to Subsection 700.3.05.G.
Use wood fiber mulch in hydroseeding according to Subsection 700.3.05.F.1.
700.2.01 Omitted
700.3 Construction Requirements
700.3.01 Omitted
700.3.02 Equipment
Use grassing equipment able to produce the required results.
Never allow the grading (height of cut) to exceed the grassing equipment’s operating range.
A. Blower Equipment
When using blower equipment to apply bituminous treated mulch in a single operation, place
two or more jets or spray nozzles at or near the end of the discharge spout to eject a uniform
coat of mulch.
B. Mulch Material Equipment
Use mulching equipment that uniformly cuts the specified materials into the soil to the
required control depth.
C. Rollers
Use at least 12 in (300 mm) diameter rollers with corrugated or notched surfaces. Do not use
smooth surface rollers.
D. Hydroseeding Equipment
For hydroseeding equipment, see Subsection 700.3.05.F.
700.3.03 Omitted
700.3.04 Omitted
Section 700 - Grassing
Page 114
700.3.05 Construction
Follow the planting zones, planting dates, types of seed, seed mixtures, and application rates
described throughout this Section.
In general:
Obtain the Engineer’s approval before changing the ground cover type.
Do not use annual rye grass seeds with permanent grassing.
Follow the planting zones indicated on the Georgia State Planting Zone Map,
below.
Sod may be installed throughout the year, weather permitting.
For permanent grassing, apply the combined amounts of all seeds for each time period
within each planting zone and roadway location listed in the Seeding Table, below. Do not
exceed the amounts of specified seed.
Section 700 - Grassing
Page 115
Planting Zone Map
SEEDING TABLE
A. Ground Preparation
Prepare the ground by plowing under any temporary grass areas and preparing the soil as
follows:
1. Slopes 3:1 or Flatter
On slopes 3:1 or flatter, plow shoulders and embankment slopes to between 4 in and 6 in
(100 mm and 150 mm) deep.
Plow front and back slopes in cuts to no less than 6 in (150 mm) deep. After plowing,
thoroughly disk the area until pulverized to the plowed depth.
Section 700 - Grassing
Page 116
2. Slopes Steeper Than 3:1
Serrate slopes steeper than 3:1 according to Plan details when required.
On embankment slopes and cut slopes not requiring serration (sufficient as determined by
the Engineer), prepare the ground to develop an adequate seed bed using any of the
following methods as directed by the Engineer:
Plow to a depth whatever depth is practicable.
Use a spiked chain.
Walk with a cleated track dozer.
Scarify.
Disking cut slopes and fill slopes is not required.
3. All Slopes
a. Obstructions
Remove boulders, stumps, large roots, large clods, and other objects that interfere with
grassing or may slide into the ditch.
b. Topsoil
Spread topsoil stockpiled during grading evenly over cut and fill slopes after preparing the
ground.
Push topsoil from the top over serrated slopes. Do not operate equipment on the face of
completed serrated cuts.
B. Grassing Adjacent to Existing Lawns
When grassing areas adjacent to residential or commercial lawns, the Engineer shall change
the plant material to match the type of grass growing on the adjacent lawn. The Contract Unit
Price will not be modified for this substitution.
If the Engineer believes bituminous treated mulch would harm other portions of the work,
bituminous treated mulch may be substituted with 1,500 lbs/acre (1680 kg/ha) of wood fiber
mulch with tackifier.
C. Temporary Grassing
Apply temporary grassing according to Subsection 163.3.05.F and the following:
Determine lime requirements by a laboratory soil test.
Add mulch only if the temporary grass does not provide adequate mulch to meet the
requirements of Subsection 700.3.05.G.
In March or April of the year following planting and as soon as the weather is suitable, replace
all areas of temporary grass with permanent grass by plowing or overseeding using the no‐till
Section 700 - Grassing
Page 117
method. If the no‐till method is used, ensure that temporary grass is less than 3 inches in
height (this may be achieved by mowing). Additional mulch will be required only if the
temporary grass does not provide adequate mulch to meet the requirements of Subsection
700.3.05.G, “Mulching.”
Temporary grass, when required, will be paid for according to Section 163.
D. Applying Agricultural Lime and Fertilizer Mixed Grade Apply and mix lime and fertilizer
as follows:
1. Agricultural Lime
Uniformly spread agricultural lime on the ground at the approximate rate determined by the
laboratory soil test.
2. Fertilizer Mixed Grade
Uniformly spread the fertilizer selected according to Subsection 700.2.D over the ground at
approximately 1,200 lbs/acre (1350 kg/ha).
If using a higher analysis fertilizer with hydroseeding, apply it at the same rate per acre
(hectare) as the standard fertilizer.
3. Mixing
Before proceeding, uniformly work the lime and fertilizer into the top 4 in (100 mm) of soil
using harrows, rotary tillers, or other equipment acceptable to the Engineer.
On cut slopes steeper than 3:1, other than serrated slopes, reduce the mixing depth to the
maximum practical depth as determined by the Engineer.
Omit mixing on serrated slopes.
E. Seeding
Following is a list of both common names and botanical names for approved seed types.
Whenever seeds are specified by the common names, the strains indicated by their botanical
name apply.
Common Name Botanical Name
Annual Ryegrass Lolium multiflorum
*Bermuda Grass, Common Hulled and Unhulled Cynodon dactylon
**Crimson Clover Trifolium incranatum Var. Reseeding
**Lespedeza Virgata Lespedeza Ambro Virgata
Section 700 - Grassing
Page 118
**Lespedeza Sericea Lespedeza cuneta, Var. Sericea
Common Name Botanical Name
**Lespedeza Serala Lespedeza cuneta, Var. Serala
**Lespedeza Interstate Lespedeza cuneta, Var. Interstate
**Lespedeza Korean Lespedeza stipulacea Maxim
Pensacola Bahiagrass Paspalum notatum, var. Pensacola
Tall Fescue Festuca arundinacea
Weeping Love Grass Eragrostis curvula
**White Dutch Clover Trifolium repens
**Crown Vetch Coronilla Varia
*Do not use Giant Bermuda Seed (Cynodon species) including NK‐37.
**Requires inoculation.
Prepare seed and sow as follows:
1. Inoculation of Seed
Inoculate each kind of leguminous seed separately with the appropriate commercial culture
according to the manufacturer’s instructions for the culture.
When hydroseeding, double the inoculation rate.
Protect inoculated seed from the sun and plant it the same day it is inoculated.
2. Sowing
Weather permitting, sow seed within 24 hours after preparing the seed bed and applying the
fertilizer and lime, or sow seed within 24 hours after applying mixed‐in‐place mulch.
Sow seed uniformly at the rates specified in the Seeding Table. Use approved mechanical seed
drills, rotary hand seeders, hydraulic equipment, or other equipment to uniformly apply the
seed. Do not distribute by hand.
To distribute the seeds evenly sow seed types separately, except for similarly sized and
weighted seeds. They may be mixed and sown together.
3. Rolling
Section 700 - Grassing
Page 119
Roll seeded areas before applying mulch, except on steep slopes where rollers cannot operate
satisfactorily. On slopes inaccessible to compaction equipment, cover the seeds by dragging
spiked chains over them or by using other methods.
Do not sow during windy weather, when the prepared surface is crusted, or when the ground
is frozen, wet, or otherwise nontillable.
4. Overseeding
Temporary grass areas that were prepared in accordance with Subsection 700.3.05.A, shall be
overseeded using the no‐till method. The no‐till method is defined by planting permanent
grass seeds using a drill‐type seeder over existing temporary grass without plowing or tilling
soil and in accordance with Subsection 700.3.05.C. This method shall be shown on the Plans
or directed by the Engineer before being implemented.
F. Hydroseeding
Hydroseeding may be used on any grassing area. Under this method, spread the seed,
fertilizer, and wood fiber mulch in the form of a slurry. Seeds of all sizes may be mixed
together. Inoculate the seeds at double the rate for seeds not being hydroseeded. Apply
hydroseeding as follows:
1. Use wood fiber mulch as a metering agent and seed bed regardless of which
mulching method is chosen. Apply wood fiber mulch at approximately 1,500 lbs/acre
(560 kg/ha).
2. Prepare the ground for hydroseeding as for conventional seeding in
Subsection 700.3.05.A.
3. Use specially designed equipment to mix and apply the slurry uniformly over
the entire seeding area.
4. Agitate the slurry mixture during application.
5. Discharge slurry within one hour after being combined in the hydroseeder. Do
not hydroseed when winds prevent an even application.
6. Closely follow the equipment manufacturer’s directions unless the Engineer
modifies the application methods.
7. Mulch the entire hydroseeded area according to Subsection 700.3.05.F.1,
above, and Subsection 700.3.05.G, below.
G. Mulching
Except as noted in Subsection 700.3.05.B and Subsection 700.3.05.C, apply mulch
immediately after seeding areas as follows:
Areas with permanent grass seed and covered with slope mats or blankets will not require
mulch.
Section 700 - Grassing
Page 120
Evenly apply straw or hay mulch between 3/4 in and 1‐1/2 in (20 mm and 40 mm) deep,
according to the texture and moisture content of the mulch material.
Mulch shall allow sunlight to penetrate and air to circulate as well as shade the ground,
reduce erosion, and conserve soil moisture. If the type of mulch is not specified on the Plans
or in the Proposal, use any of the following as specified.
1. Mulch with Binder
Apply mulch with binder regardless of whether using ground or hydroseeding equipment for
seeding.
a. Mulch uniformly applied manually or with special blower equipment designed
for the purpose. When using a blower, thoroughly loosen baled material before
feeding it into the machine so that it is uniformly coated with binder and broken
up.
b. After distributing the mulch initially, redistribute it to bare or inadequately
covered areas in clumps dense enough to prevent new grass from emerging.
Do not apply mulch on windy days.
c. Apply enough binder to the mulch to hold it in place. Immediately replace
mulch that blows away.
When using a power blower to distribute the mulch, spray the binder onto the mulch as the
mulch is ejected from the machine. If distributing the mulch by hand, immediately apply the
binder uniformly over the mulched areas.
Use one of the following binders:
Emulsified asphalt, SS‐1h or SS‐1 (Section 822) : The public, adjacent property, bridges,
pavements, curbs, sidewalks, and other existing structures shall be protected from
discoloration by the asphalt. Correct discoloration damage at no expense to the Government.
Tackifier: Use a tackifier listed in the Laboratory Qualified Products Manual may be used
at the manufacturer’s recommended rates.
2. Mixed‐in‐Place Mulch
Apply mixed‐in‐place mulch on flat areas or slopes 3:1 or less and treat as follows:
a. Immediately work the mulch into the soil with appropriate equipment to
produce a loose soil and mulch mixture 3 in to 3.5 in (75 mm to 90 mm) deep.
b. After mixing mulch and soil and restoring areas to line and grade, seed as
specified in this Section.
3. Walked‐in‐Mulch
Apply walked‐in‐mulch on slopes ranging in steepness from 5:1 to 2:1 and treat as follows:
Section 700 - Grassing
Page 121
a. Immediately walk it into the soil with a cleated track dozer. Make dozer
passes vertically up and down the slope.
b. Where walked‐in‐mulch is used, do not roll or cover the seeds as specified in
Subsection 700.3.05.E.3.
H. Sod
Furnish and install sod in all areas shown on the Plans or designated by the Engineer.
1. Kinds of Sod
Use only Common Bermudagrass (Cyndon dactylon) or one of the following Bermudagrass
varieties:
Tifway 419
Tifway II
Tift 94
Tifton 10
Midlawn
Midiron
GN‐1
Vamont
No dwarf Bermuda types shall be used. Sod shall be nursery‐grown and be accompanied with
a Georgia Department Of Agriculture Live Plant License Certificate or Stamp. Sod shall consist
of live, dense, well‐rooted material free of weeds and insects as described by the Georgia Live
Plant Act.
2. Type And Size Of Sod:
Furnish either big roll or block sod. Ensure that big roll sod is a minimum of 21 inches wide by
52 feet long. Minimum dimensions for block sod are 12 inches wide by 22 inches long. Ensure
all sod consists of a uniform soil thickness of not less than 1 inch.
3. Ground Preparation
Excavate the ground deep enough and prepare it according to Subsection 700.3.05.A to allow
placing of sod. Spread soil, meeting the requirements of Subsection 893.2.01, on prepared
area to a depth of 4 inches.
4. Application Of Lime And Fertilizer
Apply lime and fertilizer according to Subsection 700.3.05.D within 24 hours prior to installing
sod.
5 Weather Limitation
Section 700 - Grassing
Page 122
Do not place sod on frozen ground or where snow may hinder establishment.
6. Install Sod
Install Sod as follows:
Place sod by hand or by mechanical means so that joints are tightly abutted with no
overlaps or gaps. Use soil to fill cracks between sod pieces, but do not smother the grass.
Stake sod placed in ditches or slopes steeper than 2:1 or any other areas where
sod slipping can occur.
Use wood stakes that are at least 8 in (200 mm) in length and not more than 1 in
( 25 mm) wide.
Drive the stakes flush with the top of the sod. Use a minimum of 8 stakes per square yard
(meter) to hold sod in place.
Once sod is placed and staked as necessary, tamp or roll it using adequate equipment
to provide good contact with soil.
Use caution to prevent tearing or displacement of sod during this process. Leave the
finished surface of sodded areas smooth and uniform.
7. Watering Sod
After the sod has been placed and rolled or tamped, water it to promote satisfactory growth.
Additional watering will be needed in the absence of rainfall and during the hot dry summer
months. Water may be applied by Hydro Seeder, Water Truck or by other means approved by
the Engineer.
8. Dormant Sod
Dormant Bermuda grass sod can be installed. However, assume responsibility for all sod
through establishment and until final acceptance.
9. Establishment
Sod will be inspected by the Engineer at the end of the first spring after installation and at the
time of Final Inspection. Replace any sod that is not live and growing. Any cost for replacing
any unacceptable sod will be at the Contractor’s expense.
I. Application of Nitrogen
Apply nitrogen at approximately 50 lbs/acre (56 kg/ha) when specified by the Engineer after
plants have grown to2 in (50 mm) high.
One application is mandatory and must be applied before Final Acceptance.
Apply nitrogen with mechanical hand spreaders or other approved spreaders capable of
uniformly covering the grassed areas. Do not apply nitrogen on windy days or when the
foliage is damp.
Section 700 - Grassing
Page 123
Do not apply nitrogen between October 15 and March 15 except in Zone 4.
700.3.06 Quality Acceptance
The Engineer may require replanting of an area that shows unsatisfactory growth for any
reason at any time.
Except as otherwise specified or permitted by the Engineer, prepare replanting areas
according to the Specifications as if they were the initial planting areas. Use a soil test or the
Engineer’s guidance to determine the fertilizer type and application rate, then furnish and
apply the fertilizer.
700.3.07 Contractor Warranty and Maintenance
A. Plant Establishment
Before Final Acceptance, provide plant establishment of the specified vegetation as follows:
1. Plant Establishment
Preserve, protect, water, reseed or replant, and perform other work as necessary to keep the
grassed areas in satisfactory condition.
2. Watering
Water the areas during this period as necessary to promote maximum growth.
3. Mowing
Mow seeded areas of medians, shoulders, and front slopes at least every 6 months. Avoid
damaging desirable vegetation.
In addition, mow as necessary to prevent tall grass from obstructing signs, delineation, traffic
movements, sight distance, or otherwise becoming a hazard to motorists.
Do not mow lespedezas or tall fescue until after the plants have gone to seed.
B. Additional Fertilizer Mixed Grade
Apply fertilizer at approximately 600 lbs/acre (675 kg/ha) each spring after initial plant
establishment. Continue annual applications until Final Acceptance. This additional fertilizer
will be measured and paid for at the Contract Unit Price for fertilizer mixed grade.
C. Growth and Coverage
Provide satisfactory growth and coverage, ensuring that vegetation growth is satisfactory with
no bare spots larger than1 ft² (0.1 m²). Bare spots shall comprise no more than 1 percent of
any given area. An exception is given for seed not expected to have germinated and shown
growth at that time.
D. Permissible Modifications
Section 700 - Grassing
Page 124
When all Items of the work are ready for Final Acceptance except for newly planted repaired
areas or other areas with insufficient grass, the Contractor may fill the eroded areas or treat
bare areas with sod obtained, placed, and handled according to Subsection 700.3.05.H.
Carefully maintain the line and grade established for shoulders, front slopes, medians, and
other critical areas.
Sod as described above will not be paid for separately, but will be an acceptable substitute for
the satisfactory growth and coverage required under this Specification. These areas treated
with sod are measured for payment under the Item for which the sod is substituted.
700.4 Measurement
A. Permanent Grassing
Permanent Grassing will be measured for payment as lump sum.
B. Mulches
Mulches, including wood fiber mulch, furnished by the Contractor for permanent grassing are
not measured for separate payment.
C. Quantity of Sod
Sod is measured for payment by the number of square yards (meters) , surface measure,
completed and accepted.
D. Water
Water furnished and applied to promote a satisfactory growth is not measured for payment.
E. Quantity of Lime and Fertilizer Mixed Grade
Lime and fertilizer are measured by the ton (megagram).
F. Quantity of Nitrogen Used for Permanent Grassing
Nitrogen is measured in pounds (kilograms) based on the weight of fertilizer used and its
nitrogen content.
G. Replanting and Plant Establishments
No measurement for payment is made for any materials or work required under Subsection
700.3.06 and Subsection 700.3.07.
H. Temporary Grass
Temporary grass is measured for payment by the pound (kilogram) of seed according to
Section 163.
700.4.01 Omitted
700.5 Payment
Section 700 - Grassing
Page 125
As grassing and planting progress, the Contractor will receive full measurement and payment
on regular monthly estimates provided the work complies with the Specifications.
A. Permanent Grassing
Permanent grassing will be paid for Lump Sum, complete and in place. Payment is full
compensation for preparing the ground, seeding, mulching, and providing plant
establishment.
1. 70% of the Contract Price will be paid at the satisfactory completion of the
installation.
2. 20% of the Contract Price will be paid upon satisfactory review of sod which is
healthy, weed free and viable at the inspection made at the end of the first spring
after installation.
3. 10% of the contract price will be paid upon satisfactory review of sod that is
healthy, weed free and viable at the Final Acceptance.
B. Fertilizer Mixed Grade
Fertilizer mixed grade will be paid for at the Contract Price per ton. Payment is full
compensation for furnishing and applying the material.
C. Lime
Lime will be paid for at the Contract Price per ton. Payment is full compensation for furnishing
and applying the material.
D. Nitrogen
Nitrogen will be paid for at the Contract Price per pound (kilogram) of nitrogen content.
Payment is full compensation for furnishing and applying the material.
E. Sod
Sod will be paid by the square yard in accordance with the following schedule of payments.
Payment is full compensation for ground preparation, including addition of topsoil, furnishing
and installing live sod, and for Plant Establishment.
4. 70% of the Contract Price per square yard will be paid at the satisfactory
completion of the installation.
5. 20% of the Contract Price will be paid upon satisfactory review of sod which is
healthy, weed free and viable at the inspection made at the end of the first spring
after installation.
6. 10% of the contract price will be paid upon satisfactory review of sod that is
healthy, weed free and viable at the Final Acceptance.
Section 700 - Grassing
Page 126
F. Temporary Grass
Temporary Grass will be paid for under Section 163.
Payment will be made under:
700‐6910 Permanent grassing Lump sum
700‐9300 Sod Square Yard
Page 127
Section 710—Permanent Soil Reinforcing Mats
710.1 General Description
This work includes furnishing and placing a permanent mat over prepared areas according to the Plans or as
directed by the Engineer.
710.1.01 Omitted
710.02 Omitted
710.1.03 Omitted
710.2 Materials
Use materials listed in the QPL 49 .
Ensure that materials meet the following requirements.
A. Preformed Mat
Use mat with a web of mechanical or melt‐bonded polymer nettings, monofilaments, or fibers entangled to
form a dimensionally stable matrix. Bond the mat with one of the following:
Polymer welding
Thermal fusion
Polymer fusion
Fibers placed between two high‐strength, biaxially oriented nets bound by parallel‐lock stitching with
polyolefin, nylon, or polyester threads
Use a mat with enough strength and elongation to limit stretching and maintain its shape before, during, and
after installation under dry or wet conditions. Provide a mat with stabilized components that avoid ultraviolet
degradation and are inert to chemicals normally encountered in a natural soil environment. Ensure that the mat
conforms to the following physical properties:
Property Minimum Value Test Method
Thickness 1/2 in (13 mm)
Weight 0.60 lbs/yd² (325 g/m²)
Roll width 38 in (965 mm)
Tensile strength ASTM D 5034*
Length (50% elongation) 15 lbs/in (2.5 N/mm)
Section 716 – Erosion Control Mats (Slopes)
Page 128
Length (ultimate) 20 lbs/in (3.5 N/mm)
Width (50% elongation) 5 lbs/in (1 N/mm)
Width (ultimate) 10 lbs/in (2 N/mm)
Ultraviolet stability 80% ASTM D 4355
1,000 hours in an Atlas ARC Weatherometer (ASTM G 23, Type D) ASTM D 822
B. Stakes or Staples
Use 1 in by 3 in (25 mm by 75 mm) wood stakes made from sound stock cut in a triangular shape. Cut stakes 12
in to 18 in (300 mm to 450 mm) long depending on soil compaction. Use metal staples with the following
characteristics:
Diameter of 1/8 in (3 mm) or greater
U shape
Legs at least 8 in (200 mm) long
Crown 2 in (50 mm) across
C. Filter Fabric
Use woven or nonwoven filter fabric that meets the requirements of Subsection 881.2.05, “Plastic Filter Fabric.”
710.2.01 Delivery, Storage, and Handling General Provisions 101 through 150.
710.3 Construction Requirements
710.3.01 Personnel
General Provisions 101 through 150.
710.3.02 Equipment
General Provisions 101 through 150.
710.3.03 Preparation A. Site Preparation
Before protecting areas with mat, prepare the area according to Section 700 with the following steps:
1. Bring to final grade
2. Plow
3. Lime
4. Fertilize
Section 716 – Erosion Control Mats (Slopes)
Page 129
Provide a smooth, firm, and stable surface free of rocks, clods, roots, or other obstructions that would prevent
the mat from contacting the soil directly.
710.3.04 Omitted
710.3.05 Construction
A. Installing Mat
Do not use a mat in areas with rock outcroppings or large rocks. Install the mat either in ditches or on slopes
according to the following requirements:
1. Ditches
To install the mat in ditches:
a. Cut a transverse trench 6 in wide by 9 in deep (150 mm wide by 225 mm deep) at the ends of
the mat and at 25 ft (7.5 m) intervals along the ditch.
b. Cut longitudinal, 4 in (100 mm) deep anchor slots along each side of the mat along the full
length of the ditch, burying mat edges.
c. Roll out the center strip of matting, starting at the lower end of the ditch.
d. Roll out each adjacent strip of matting to overlap the preceding strip at least 3 in (75 mm).
e. Overlap the ends of each mat roll 3 ft (1 m) with the upslope mat on top. Stretch the mat to the
bottom of the slot, folding it back and staking through two layers of material.
f. Stake each strip of matting at 1 ft (300mm) intervals in each anchor slot, with one stake serving
the overlapped edges of adjoining strips.
g. Backfill and compact the slot.
h. Fold the mat back over the slot and continue in the upstream direction (closed anchor slot).
i. Stake the mat snugly in the longitudinal slots and at intervals a maximum of 5 ft (1.5 m) along
the ditch (open anchor slot).
j. Backfill and dress the longitudinal anchor slots.
Lay up to 10 ft (3 m) of filter fabric under runs of matting that begin at pipe outlets.
B. Grassing
Grass the entire soil‐filled mat and disturbed soil area according to Section 700.
710.3.06 Omitted
710.3.07 Omitted
710.4 Measurement
Permanent soil‐reinforcing mat complete and accepted is measured for payment by the square yard (meter),
surface measured.
Section 716 – Erosion Control Mats (Slopes)
Page 130
710.4.01 Limits
Overlaps and anchor slots are incidental to the work and are not measured for payment.
710.5 Payment
This work will be paid for at the Contract Price per square yard for permanent soil‐reinforcing mat, complete in
place and accepted. Payment is full compensation for furnishing and installing the mat according to this
Specification, including filter fabric and maintenance.
Preparing the area and grassing will be paid for according to Section 700.
Payment will be made under:
Item No. 710 Permanent soil reinforcing mat Per square yard
Page 131
Section 716—Erosion Control Mats (Slopes)
716.1 General Description
This work includes furnishing and placing erosion control mats (blankets) made of fiberglass, excelsior, jute
mesh, bituminous treated roving, and straw, synthetic, or coconut over grass areas prepared according to
Section 700 for permanent grass. Place according to the Plans or as directed by the Engineer. This specification
is not applicable for waterways.
716.2 Omitted
716.3 Construction Requirements
716.3.01 Omitted
716.3.02 Omitted
716.3.03 Omitted
716.3.04 Omitted
716.3.05 Construction
The contractor may elect to use either Section 712 – Fiberglass Blanket, Section 713 – Organic and Synthetic
Material Fiber
Blanket (except do not use Type II Wood Fiber Blanket), Section 714 – Jute Mesh Erosion Control, or Section 715
– Bituminous Treated Roving, on slopes. All of the materials, construction and measurement portions of the
noted sections apply to the type mat (blanket) selected for use.
Place blankets or mats vertically on the slopes beginning at the top of the slope and extending to the bottom of
the slope. Horizontal installation of the blankets or mats is not permitted.
The application of mulch is not required for permanent grassing when one of the above noted mats or blankets
is placed on the previously prepared and grassed slopes with 24 hours.
716.4 Measurement
Erosion control mats (Slopes) are measured according to the Specification sections referenced in Subsection
716.3.05.
716.4.01 Limits
General Provisions 101 through 150.
716.5 Payment
Erosion control mats (Slopes), measured as specified in Section 712, Section 713, Section 714, or Section 715 will
be paid for at the Contract Unit Price per square yard.
Section 716 – Erosion Control Mats (Slopes)
Page 132
This payment is full compensation for constructing the mat (blanket) and providing materials, equipment, tools,
labor, and incidentals needed to maintain mats (blankets) for the life of the Contract or until a stand of grass has
developed enough to prevent erosion.
Payment will be made under:
Item No. 716 Erosion control mats (slopes) Per square yard (meter)