chapter 1 - stress and strain.pdf
DESCRIPTION
mechanicalTRANSCRIPT
28/02/2012
1
STRESS AND STRAIN
2
28/02/2012
2
Topics:
• Introduction• Main Principles of Statics
StressStress• Normal Stress• Shear Stress• Bearing Stress• Thermal Stre
Mechanics : The study of how bodies react to forces acting on them
RIGID BODIES(Things that do not change shape)
Statics : The study of bodies in an equilibrium
DEFORMABLE BODIES(Things that do change shape) FLUIDS
Incompressible Compressible
41.1 Introduction
Mechanics of Materials :The study of the relationships between the external loads applied to a deformable body and the intensity of internal forces acting within the body.
Dynamics :1. Kinematics – concerned with the geometric aspects of the motion2. Kinetics – concerned with the forces causing the motion.
28/02/2012
3
External Loads
Surface Forces- caused by direct contact of one body withthe surface of another.
Body Force- developed when one body exerts a force on another body without direct physical contactbetween the bodies.- e.g earth’s gravitation (weight)
concentrated force
51.2 Main Principles of Statics
linear distributed load, w(s)
Axial LoadNormal StressShear StressBearing StressAllowable StressDeformation of Structural under Axial LoadStatically indeterminate problemh lThermal Stress
28/02/2012
4
Mechanics of material is a study of the relationship between the external loads applied to a deformable body and the intensity of i t l f ti ithi th b dinternal forces acting within the body.
Stress = the intensity of the internal force on a specific plane (area) passing through a point.
Strain = describe the deformation by changes inStrain describe the deformation by changes in length of line segments and the changes in the angles between them
• Normal Stress : stress which acts perpendicular, or normal to, the(σ) cross section of the load-carrying member.( ) y g
: can be either compressive or tensile.• Shear Stress : stress which acts tangent to the cross section of
(τ) the load-carrying member.: refers to a cutting-like action.
81.1 Introduction
28/02/2012
5
Normal Stress, σthe intensity of force, or force per unit area, acting normal to ΔAnormal to ΔA
A positive sign will be used to indicate a tensile stress (member in tension)
σ = P / A
A negative sign will be used to indicate a compressive stress (member in compression)
(a)
(b)
•Unit: Nm -² •N/mm2 or MPa
Stress ( σ ) = Force (P)
Cross Section (A)
•N/mm2 or MPaN/m2 or Pa
28/02/2012
6
Assumptions :1. Uniform deformation: Bar1. Uniform deformation: Bar
remains straight before and after load is applied, and cross section remains flat or plane during deformation
2. In order for uniform deformation, force P be
111.4 Axial Loading – Normal Stress
de o at o , o ce beapplied along centroidal axis of cross section C
AFFFAzRz =Σ=↑+ ∫ ∫ σ dd;
APAPA
=
=∫ ∫
σ
σ
σ = average normal stress at any point on cross sectional area
12
on cross sectional areaP = internal resultant normal forceA = cross-sectional area of the bar
1.4 Axial Loading – Normal Stress
28/02/2012
7
• Use equation of σ = P/A for cross-sectional area of a member when section subjected to internal resultant force Psection subjected to internal resultant force P
Internal Loading• Section member perpendicular to its longitudinal axis at pt where normal stress is to be determined
• Draw free-body diagram• Use equation of force equilibrium to obtain internal axial force P at the section
13
force P at the section
• Determine member’s x-sectional area at the section• Compute average normal stress σ = P/A
Average Normal Stress
1.4 Axial Loading – Normal Stress
Example 1.1:Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1=30mm and d2=20mm, find average normal stress at the midsection of (a) rod AB, (b) rod BC(b) rod BC.
28/02/2012
8
Example 1.2Two solid cylindrical roads AB and BC are welded
together at B and loaded as shown. Knowing that d1 = 30 mm and d2 = 50 mm, find the average normal stress in the mid section of (a)average normal stress in the mid section of (a) rod AB, (b) rod BC.
28/02/2012
9
Normal strain, ε is the elongation or contraction of a line segment per unit of length ε = ΔL / Lo
ΔL = elongationLo = length
δ strain normalL
=δ
=ε
* ΔL= δ
28/02/2012
10
Example 1.3:Determine the corresponding strain for a bar of length L=0.600m and uniform cross section which undergoes a deformation δ=150×10-6m.
66150 10 m 250 10 m m
L 0 600m/
.
−−δ ×
ε= = = ×
6250 10 250@−= × μ
1.4 A cable and strut assembly ABC supports a vertical load P=12kN. The cable has an effective cross sectional area of 160mm², and the strut has an area of 340mm².
(a) Calculate the normal stresses in the cable and strut.(b) If the cable elongates 1.1mm, what is the strain?(c) If the strut shortens 0.37mm, what is the strain?
28/02/2012
11
1.5 The bar shown has a square cross section (20mm x 40mm) and length, L=2.8m. If an axial force of 70kN is applied along the centroidal axis of the bar cross sectional area, determine the stress and strain if the bar end up with 4m lengthup with 4m length.
70kN 70kN
2.8m
Tensile test is an experiment to determine the load-deformation behavior of the material.Data from tensile test can be plot into stress and strain diagram.Example of test specimen- note the dog-bone geometry
28
28/02/2012
12
Universal Testing Machine - equipment used to subject a specimen to tension, compression, bending, etc. loads and measure its response
29
Stress-Strain Diagrams
A number of important mechanicalproperties of materials that can be deducedfrom the stress-strain diagram are illustratedin figure above.
30
28/02/2012
13
Point O-A = linear relationship between stressand strain
Point A = proportional limit (σPL)The ratio of stress to strain in this linear regionof stress-strain diagram is called Young Modulusor the Modulus of Elasticity given
σΔΔ
=Ε σ < σAt point A-B, specimen begins yielding.Point B = yield point Point B-C = specimen continues to elongate without any increase in stress. Its refer as perfectly plastic zone Point C = stress begins to increasePoint C-D = refer as the zone of strain hardeningPoint D = ultimate stress/strength ; specimen
b i t k d
εΔ σ < σPLUnit: MPa
begins to neck-downPoint E = fracture stress
31
Point O to A
Point C to D
Point D to EPoint D to E
At point E
Normal or engineering stress can be determinedby dividing the applied load by the specimenoriginal cross sectional areaoriginal cross sectional area. True stress is calculated using the actual crosssectional area at the instant the load ismeasured.
31
28/02/2012
14
Some of the materials like aluminum (ductile), does not have clear yield point likesstructural steel. Therefore, stress valuecalled the offset yield stress, σYL is usedin line of a yield point stress.
As illustrated, the offset yield stress isdetermine by;
Drawing a straight line that best fits the data in initial (linear) portion of the stress-strain diagramportion of the stress strain diagramSecond line is then drawn parallel to the original line but offset by specified amount of strainThe intersection of this second line with
the stress-strain curve determine theoffset yield stress.
Commonly used offset value is 0.002/0.2%
32
Brittle material such as ceramic and glass have low tensile stress value but high incompressive stress. Stress-strain diagram for brittle material.
Example 1.6The 4 mm diameter cable BC is made of a steelwith E=200GPa. Knowing that the maximumstress in the cable must not exceed 190MPaand that the elongation of the cable must notexceed 6mm, find the maximum load P that canbe applied as shown
33
28/02/2012
15
Elasticity refers to the property of a material such that it returns to its original dimensions after unloading .Any material which deforms when subjected to load and returns to its original dimensions when unloaded i id b l iis said to be elastic.If the stress is proportional to the strain, the material is said to be linear elastic, otherwise it is non-linear elastic.Beyond the elastic limit, some residual strain or permanent strains will remain in the material upon unloadingunloading .The residual elongation corresponding to the permanent strain is called the permanent set .
34
• The amount of strain which is recovered upon unloading is called the elastic recovery.
35
28/02/2012
16
When an elastic, homogenous and isotropic material is subjected to uniform tension, it stretches axially but contracts laterally along its entire length. Similarly, if the material is subjected to axial compression it shortens axially but bulges outcompression, it shortens axially but bulges out laterally (sideways). The ratio of lateral strain to axial strain is a constant known as the Poisson's ratio,
axial
lateralvεε
=
where the strains are caused by uniaxial stress only
36
paksi x
sisi y
LLb db d
@
@
δε ε =
δ δε ε = − = −
Example 1.7A prismatic bar of circular cross-sectionis loaded by tensile forces P = 85 kN. Thebar has length of 3 m and diameter of 30mm. It is made from aluminum with modulusof elasticity of 70 GPa and poisson's ratio ν= 1/3. Calculate the elongation and thedecrease in diameter Δd.
37
28/02/2012
17
Example 1.8A 10 cm diameter steel rod is loaded with 862 kN by tensile forces. Knowing that the E=207 GPa and ν= 0.29, determine the deformation of rod diameter after being loaded. Solution
in rod σ MPaNxp 710910862 3
==σ in rod, σ =
Lateral strain,
MPamA
7.109)1.0(
41 22
==π
00053.010207
7.1093 ===
MPaxMPa
Eaσε
)000530(29)( ol −=−= ενε∴
38
)00053.0(29.)( oal == ενε000154.0−=
)1.0)(000154.0()( −==Δ Dd lεcm00154.0−=
Exercises 11. A steel pipe of length L=1.2 m, outside diameter d2=150mm and
inside diameter d1=110mm is compressed by an axial force P= 620kN.The material has modulus of elasticity E= 200GPa and Poisson’s Ratio v = 0.30.Determine :
a) the shortening, δ ( ans :-0.455 mm)b) h l l i ( 113 9 10 6)b) the lateral strain,ε lateral (ans: 113.9x10-6)c) the increase ∆d2 in the outer diameter and the increase ∆d1 in the inner diameter
(ans: 0.0171 mm and 0.0125mm)d) the increase ∆t in the wall thickness
(ans: 0.00228 mm)
39
28/02/2012
18
2. A hollow circular post ABC as shown in Figure 2 supports a load P1=7.5 kN acting at the top. A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB=32 mm, tAB= 12mm, dBC 57 mm and tBC=9mm, respectively.a) Calculate the normal stress, σAB in the upper part
of the post (ans: 9 95 MPa)of the post. (ans: 9.95 MPa)b) If it is desired that the lower part of the post
have the same compressive stress as the upper part, what should be the magnitude of the load P2? (ans : P2=6kN)
40
3. A standard tension test is used to determine the properties of an experimental plastic. The test specimen is a 15 mm diameter rod and it is subjected to a 3.5 kN tensile force. Knowing that an elongation of 11 mm and a decrease in diameter of 0.62 mm are observed in a 120 mm gage length. D i h d l f l i h d l fDetermine the modulus of elasticy, the modulus of rigidity, and Poisson’s ratio of the material.
49
28/02/2012
19
A force acting parallel or tangential to a section taken through a material (i.e. in the plane of the material) is called a shear force
The shear force intensity, i.e. shear force divided by the area over which it acts, is called the average shear stress, τ, g ,
τ = shear stressV = shear forceA = cross-sectional area
Shear stress arises as a result of the direct action of forces trying to cut through a material, it is known as direct shear force
AV
=τ
Shear stresses can also arise indirectly as a result of tension, torsion or bending of a member.
41
Depending on the type of connection, a connecting element (bolt, rivet, pin) may be subjected to single shear or double shear as shown.
Rivet in Single Shear
4
2dP
AV
πτ ==
42
28/02/2012
20
Rivet in Double Shear
Example 1.9For the 12 mm diameter bolt shown in the bolted joint below,
determine the average shearing stress in the bolt
222
)4
(2 dP
dP
AV
ππτ ===
determine the average shearing stress in the bolt.
43
Single ShearDouble Shear
AF
AP==aveτ
AF
AP
2ave ==τ
28/02/2012
21
The effect of shear stress is to distort the shape of a body by inducing shear strains The shear strain, γ is a measure of the angular distortion of the body.
L
Vx
γ
Lx
=γ
(units: degrees, radians)
L
44
Bearing stress is also known as a contact stressBearing stress in shaft key;
MMP 2
Bearing stress in rivet and plat;
rhLM
LhrM
AP
bb
2)2(
===σ
Pσtdb =σ
45
28/02/2012
22
Example 2.0A punch for making holes in steel plates is shown in the figure. Assume that a punch having diameter d=20 mm is used to punch a hole in an 8 mm plates, what is the average shear stress in the plate and the average compressive stress in the punch ifand the average compressive stress in the punch if the required force to create the hole is P = 110kN.
. P
20 mm
8 mm
46
It also known as Shear Modulus of Elasticity or the Modulus of Rigidity.Value of shear modulus can be obtained from the linear region of shear stress-strain diagram.
The modulus young (E), poisson’s ratio(ν) and the modulus of rigidity (G) can be related as
γτ G= Unit : Pa
)1(2 ν+=
EG
48
28/02/2012
23
Because of the change in the dimensions of a body as a result of tension or compression, the volume of the body also changes within the elastic limit. Consider a rectangular parallel piped having sides a, g p p p g ,b and c in the x, y and z directions, respectively.
58
The tensile force P causes an axial elongation of aεand lateral contractions of bνε and cνε in the x, y, andz directions respectively. Hence,
Initial b d
Initial volume of body V abc
body
Initial volume of body, Vo = abc Final volume, Vf = (a + aε)(b - bνε)(c - cνε)
= abc(1 + ε)(1 - νε)2
59
28/02/2012
24
Expanding and neglecting higher orders of ε (since ε is very small),
Final volume, Vf = abc(1 + ε - 2νε)
Change in volume, ΔV = Final Volume - Initial Volume
= abc(1 + ε - 2 νε) - abc = abc(1 + ε - 2 νε - 1) = abc(ε - 2 νε) = Vo ε(1 - 2 ν)
Hence,
60
)21(
)21(
νσε
νε
−=
−=Δ
E
VV
o
I i i l i bj d l i i lIsotropic material is subjected to general triaxialstress σx, σy and σz.Since all strain satisfy ε << 1, so εv = εx + εy + εz
εx =
εy =
[ ])(1zyxE
σσνσ +−
[ ])(1zxyE
σσνσ +−
εz =
[ ])( zxyE
[ ])(1yxzE
σσνσ +−
)(21zyxv E
σσσνε ++−
=
61
28/02/2012
25
Example 2.1
A titanium alloy bar has the following original dimensions: x =10cm; y = 4cm; and z = 2cm. The bar is subjected to stresses σx= 14 N and σy = - 6 N, as indicated in figure below. Theremaining stresses (σz, τxy, τxz and τyz) are all zero. Let E = 16kN and ν = 0.33 for the titanium alloy.(a)Determine the changes in the length for
Δx, Δy and Δz.
(b) Determine the dilatation, εv.
y 6 N
z
x14 N14 N
6 N
62
Applied load that is less than the load the member can fully support. (maximum load)
One method of specifying the allowable load for the design oranalysis of a member is use a number called the Factor of Safety (FS).
Allowable-Stress Design
allow
fail
FF
FS =
FS > 1
or yieldyield ττ
σσ
FSor
FSy
allowy
allow τσ ==
63
28/02/2012
26
If a bar is fixed at both ends, as shown in fig. (a), two unknown axial reactions occurs, and the force equilibrium equation becomes; ;0FΣ↑
;
0PFF
;0F
AB
y
=−+
=Σ↑+
• In this case, the bar is called statically indeterminate, since the equilibrium equation are not sufficient to determine the reactions.
• the relative displacement of one end of the bar with respect to the other end is equal to zero
0B/A =δ
• the relationship between the forces acting on the bar and its changes in length are known as force-displacement relations
with respect to the other end is equal to zero since the ends supports are fixed. Hence;
AEPL,0B/A =δ=δ 0BA =δ+δ
• Realizing that the internal force in segment AC is +FA and in segment CB
BAAB FPF,0PFF −==−+
AC
CBBA
CBBACA
CBBACA
LFLAE
AELFF
AELF
AELF
0AELF
AELF
×=
=
=−
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
+=
=−
1LLFP
FL
LFP
LLFFP
AC
CBB
BAC
CBB
AC
CBBB
Realizing that the internal force in segment AC is +FA, and in segment CB, the internal force is –FB. Therefore, the equation can be written as;
⎟⎟⎠
⎞⎜⎜⎝
⎛=
⎟⎟⎠
⎞⎜⎜⎝
⎛ +=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
LLFP
LLLFP
LL
LLFP
B
AC
ACCBB
AC
AC
AC
CBB
AC
CBBA L
LFF =⎠⎝ LAC
⎟⎟⎠
⎞⎜⎜⎝
⎛=
⎟⎠
⎜⎝
LL
PF
L
ACB
AC
28/02/2012
27
Example 2.2:Example 2.2:
3X A B
3B A
F 0 F F 20 10 N 0 1
F 20 10 F
, ( ) ................( )
( )
+ → Σ = − − + =
= −
( ) ( )
B A
A B
A AC B CB
A2 29 2 9 2
0 001m0 001m
F L F L0 001m
AE AEF 0 4m FB 0 8m 0 001m
0 0025m 200 10 Nm 0 0025m 200 10 Nm
/ ..
.
( . ) ( . ) .. .− −
δ =
δ − δ =
− =
− =⎡ ⎤ ⎡ ⎤⎡ ⎤ ⎡ ⎤π × π ×⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦⎣ ⎦ ⎣ ⎦
A B
orF 0 4m F 0 8m 3927 0N 2Substitute eq 1 oeq 2F
( . ) ( . ) . ................( )( )int ( )
− =
A A
A
0 4m 20 000N F 0 8m 3927 0NF 16 6kNFB 3 39kN
( . ) ( , )( . ) ..
.
− − =
=
=
28/02/2012
28
Example 2.3:Example 2.3:
Solution:Solution: 3y A C E
C3
A E
F 0 F F F 1 5 1 0 N 0 1
C C W M 0
F 0 4 1 5 1 0 0 2 F 0 4 0 2
, ( ) . . . . . . . . . . . . . . . . ( )
( . ) ( ) ( . ) ( . ) . . . . . . . . . . . ( )
+ ↑ Σ = + + − =
+ =∑
− + + =
The applied load will cause the horizontal line ACE move to inclined line A’C’E’
δ δδ δ C EA E
C E A E
A EC E
A EC E
C A E
C CD A AB E EF
0 8 0 4
0 4 0 8
0 40 8
0 4 0 40 8
0 5 0 5
F L F L F L0 5 0 5
. .
. .
..
. ..
. .
δ − δδ − δ=
δ − δ δ − δ=
δ − δδ − δ = ×
δ − δδ = + δ
δ = δ + δ
⎡ ⎤ ⎡ ⎤⎢ ⎥ ⎢ ⎥C CD A AB E EF
5 5 5st st st
C A5 5
st st
0 5 0 51 5 10 E 2 5 10 E 2 5 10 E
F 0 5 F 0 50 51 5 10 E 2 5 10 E
. .. . .
( . ) ( . ).. .
− − −
− −
= +⎢ ⎥ ⎢ ⎥× × ×⎢ ⎥ ⎢ ⎥⎣ ⎦ ⎣ ⎦
⎡=
× ×⎣
E5
st3 3 3
C A E3 3
A EC 3
C A E
F 0 50 52 5 10 E
33 33 10 F 10 10 F 10 10 F
10 10 F 10 10 FF33 33 10
F 0 3F 0 3F eq 3
( . )..
.
.. . ................. ( )
−
⎤ ⎡ ⎤+⎢ ⎥ ⎢ ⎥
×⎢ ⎥ ⎢ ⎥⎦ ⎣ ⎦
× = × + ×
× + ×=
×= +
28/02/2012
29
3y A C E
C3
A E
C A E
3
F 0 F F F 15 10 N 0 1
CCW M 0
F 0 4 15 10 0 2 F 0 4 0 2F 0 3F 0 3F eq 3
Substituteeq 3 o eq 1
, ( ) ................( )
( . ) ( )( . ) ( . ) ...........( ). . ................. ( )
( ) int ( )
+ ↑ Σ = + + − =
+ =∑
− + + =
= +
3A E
3 3A A
Substituteeq 4 o eq 2
F 0 4 15 10 0 2 F 0 4 0
F 0 4 3 10 0 4 11 538 10 F 0
( ) int ( )
( . ) ( )( . ) ( . )
( . ) ( ) ( . ) . ( )
− + + =
⎡ ⎤− + + − =⎣ ⎦3A C E
A
F F F 15 10 N 0 1
F
( ) ................( )+ + − =3
A E E3
A E3
AE
3E A
0 3F 0 3F F 15 10 0
1 3F 1 3F 15 10
15 10 1 3FF1 3
F 11 538 10 F eq 4
( . . ) ( )
. . ( )
( ) ..
. ( ) ....................... ( )
+ + − =
+ =
−=
= −
A A
3 3A A
3
A
3
F 0 4 3 10 4 615 10 0 4F 0
7 61510F0 8
9 519 109 52kN
( ) ( ) ( ) ( )
( . ) ( ) . ( ) .
..
. ( ).
⎣ ⎦
− + + − =
−=
−
==
Aplace F 9 52kN o eq 49 52kN
Re . int ( ).=
=3
E A3 3
E
C A E3 3
F 11 538 10 F
11 538 10 9 52 102 02kN
place F 2 02kN o eq 3F 0 3F 0 3F
0 3 9 519 10 0 3 2 02 103 462 kN
. ( )
. ( ) . ( ).
Re . int ( ). .
. ( . ( ) . ( . ).
= −
= −=
=
= +
= + ×=
A change in temperature can cause material to change its dimensions.If the temperature increases, generally a material expands, whereas if the temperature decreases, the material will contract.If this is the case, and the material is homogenous and isotropic, it has been found from experiment that the deformation of a member having a length L can be calculated using the formula;
δT=αΔTLWhere
α=linear coefficient of thermal expansion (unit: 1/C°)
ΔT=change in temperatureL=original length of the memberδT=change in length of the member
28/02/2012
30
Example 2.4:Example 2.4:
Given: α=12x10-6/C°
FFF0F
BA
Y===Σ↑+
Solution:Solution:
δAB 0=δ The change in length of the bar is zero (because the supports do not move)
AB T F( )+ ↑ δ = δ −δ
To determine the change in length, remove the upper support of the bar and obtain a bar is fixed at the base and free to displace at the upper end.So the bar will elongate by an AB T F( ) So the bar will elongate by an amount δT when only temperature change is actingAnd the bar shortens by an amount δF when only the reaction is acting
28/02/2012
31
AB T F
T F 0FLTL 0AE
F 1
( )
( )
+ ↑ δ = δ −δ
δ −δ =
αΔ − =
62 9
42 9
4 2 9
F 112 10 60 30 1 00 01 200 10
F 13 6 100 01 200 10
F 3 6 10 0 01 200 107 2kN
( )( )( ). ( )
( ).. ( )
. . ( ).
−
−
−
× ° − ° − =×
× =×
= × × ×=
Average normal thermal stress:
2F 7 2kN 72MPaA 0 01
.;.
σ= =
Average normal thermal stress:
Example 2.5Example 2.5
Given:
6st 12 10 C/−α = × °st
6al
9st
9al
12 10 C
23 10 C
E 200 10 Pa
E 73 1 10 Pa
/
/
.
−=
α ×
α × °
= ×
= ×
28/02/2012
32
3y st alF 0 2F F 90 10 N 0 eq 1, ( ) ......... ( )+ ↑ Σ = + − =
st al
st st T st F
al al T al F
eq 2............................... ( )
( ) ( ) ( )( ) ( )
( ) ( ) ( ) ( )
δ = δ
+↑ δ = δ − δ
δ = δ − δ
δ δ δ δst T st F al T al F
st al
st al
6 st2 9
6
F L F LTL TLA E A E
F 0 2512 10 80 20 0 25
0 02 200 10
23 10 80 20
( ) ( ) ( ) ( )
( . )( )( . )( . ) ( )
(
−
−
δ − δ = δ − δ
αΔ − =αΔ −
× °− ° − =π ×
× °− ° al2 9
4 4
F 0 250 250 03 73 1 10
F 0 25 F 0 25
( . ))( . )( . ) ( . )
( ) ( )
−π ×
4 4st al6 6
4 10 4 9st al
10 4 9 4st al
st
F 0 25 F 0 251 8 10 3 45 10
251 327 10 206 685 10
1 8 10 9 947 10 F 3 45 10 1 21 10 F
9 947 10 F 3 45 10 1 21 10 F 1 8 10
1 65F
( . ) ( . ). .. ) ( . )
. . . .
. . . .
.
− −
− − − −
− − − −
× − = × −× ×
× − × = × − ×
− × = × − × − ×
×=
4 9al
10
3al
10 1 21 10 F9 947 10
165 88 10 1 216F eq 3
..
. . ............... ( )
− −
−− ×
− ×
= − × +
3st al
3 3al al
3 3al al
Substituteeq 3 o eq 1
2F F 90 10 N 0
2 165 88 10 1 216F F 90 10 N 0
331 76 10 2 432F F 90 10 N 0
( )int ( )
( )
( . . ) ( )
. . ( )
+ − =
− × + + − =
− × + + − =3
al
al
al3
st
3 432F 421 76 10F 122 89 kN
Substitute F 122 89kN o eq 3
F 165 88 10 1 216F
. ..
. int ( )
. .
= ×
=
=
= − × + al3 3165 88 10 1 216 122 89 10
16 445kN. . ( . )= − × + ×
= −16 445kN.=
The negative value for F steel indicates that the force acts opposite to arrow shown.THE STEEL POSTS ARE IN TENSION and ALUMINIUM POSTS IS IN COMPRESSION
28/02/2012
33
TUTORIAL 1
Determine the reactions at A and B for the steel barand loading shown, assuming a close fit at bothsupports before the loads are applied.
66
Answer, RA= 323 kN, Rb= 577kN
TUTORIAL 2Two cylindrical rods, CD made of steel (E=200 GPa) and AC made of aluminum (E=72 GPa), are joined at C andrestrained by rigid supports at A and D. Determine (a) the reactions at A and D (RA=52.9kN, RD= 87.1 kN)(b) The deflection of point C (0 086 mm)(b) The deflection of point C (0.086 mm)
67
28/02/2012
34
TUTORIAL 3At room temperature (21oC) a 0.5 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 1600C, determine (a)The normal stress in the aluminum rod (σa =-150.6 ( ) ( aMPa)(b)The change in length of the aluminum rod (δa= 0.369 mm)
69