8/12/2019 Carbothane+134+HG+PDS+3 11

http://slidepdf.com/reader/full/carbothane134hgpds3-11 1/2

Carbothane® 

134 H

March 2011 replaces December 2009 0859

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Comverify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsicoverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBEXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboare registered trademarks of Carboline Company.

Selection & Specification Data

Generic Type  Aliphatic Acrylic Polyurethane

Description Thin film, high gloss finish with exceptionalweathering performance characteristics. Usedextensively in virtually all industrial markets, 134HG provides a smooth, durable finish that hassuperior resistance to corrosion, abrasion andchemical exposure.

Features   High solids, low VOC content  Excellent weatherability  Far exceeds SSPC Paint 36 specification for a

Level 3 urethane  Available in a variety of colors including

metallic-pigmented colors  Excellent flow characteristics allow for

application by spray or roller

  Superior impact and abrasion resistance  Indefinite recoatability  VOC compliant to current AIM regulations

Color Refer to Carboline Color Guide. Certain colors,particularly in non-leaded safety oranges, redsand yellows may require multiple coats foradequate hiding. Check color suitability beforeuse.

Finish Gloss

Primers Refer to Substrates & Surface Preparation 

Topcoats Carbothane® 130 Clear Coat when required

Dry Film

Thickness

2.0-3.0 mils (50-75 µ)

May be applied up to 4 mils (100 µ) as needed

Solids Content By Volume: 70% ± 2%

TheoreticalCoverage Rate

1123 mil ft2(27.5 m

2/l at 25 µ)

 Allow for loss in mixing and application

VOC Values  As supplied: 2.2 lbs./gal (264 g/l)Thinned:25 oz/gal w/ #25: 3.06 lbs./gal (366 g/l)25 oz/gal w/ #214: 2.9 lbs./gal (348 g/l)25 oz/gal w/ #215: 3.0 lbs./gal (362 g/l)These are nominal values and may vary slightlywith color.

Dry Temp.Resistance Continuous: 200

°

F (93°

C)Non-Continuous: 250°F (121°C)Discoloration and loss of gloss is observed

above 200°F (93°C).

* The alignment of aluminum flakes in aluminum-filled finishes is verydependent on application conditions and techniques. Care must betaken to keep conditions as constant as possible to reduce variationsin final appearance. It is also advisable to work from a single batch ofmaterial since variations can occur from batch to batch. For moreinformation consult Carboline Technical Service Department.

Substrates & Surface Preparation

General Surfaces must be clean and dry. Em

adequate methods to remove dirt, dust, oil all other contaminants that could interfere adhesion of the coating. For all surfaces pwith specific Carboline primer as recommenby your Carboline sales representative. Refethe specific primer’s Product Data Sheetdetailed requirements of the specified primer.

GalvanizedSteel

Prime with specific Carboline primer recommended by your Carboline SRepresentative. Refer to the specific primProduct Data Sheet for substrate prepararequirements.

PreviouslyPainted

Surfaces

Lightly sand or abrade to roughen and degthe surface. Existing paint must attain a minim

3B rating in accordance with ASTM D3359Scribe” adhesion test.

Performance Data

Test Method System Results

 ASTM D4541 Adhesion

Blasted Steel1 ct. Epoxy

1 ct. 134 HG

2562 psi(Pneumatic)

 ASTM D3359 Adhesion

Blasted Steel1 ct. Epoxy

1 ct. 134 HG5A

 ASTM D4060 Abrasion

Blasted Steel1 ct. 134 HG

70 mg. loss after 1000cycles, CS17 wheel, 100

gm. load

 ASTM G26Weatherometer

Blasted Steel

1 ct. Epoxy1 ct. 134 HG

No blistering, rusting orcracking; gloss retention o

85%; color change of 1McAdam unit after 2000

hours.

 ASTM G53 ASTM D4587 AcceleratedWeathering

Blasted Steel1 ct. Org. Zinc

1 ct. Epoxy1 ct. 134 HG

No rusting, blistering or losof adhesion; less than 5%gloss loss after 3000 hour

 ASTM B117Salt Fog

Blasted Steel1 ct. Org. Zinc

1 ct. Epoxy1 ct. 134 HG

No rusting, blistering, lossbond or any measurablecreepage from the scribe

after 3000 hours.

 ASTM D3363Hardness

Blasted Steel1 ct. Epoxy

1 ct. 134 HGH

 ASTM D2794Impact

Resistance

Blasted Steel1 ct. 134 HG

155 inch-pounds; no visibcracking. Gardner Impac

Tester

 ASTM D870Water/Saltwater

Resistance

Blasted Steel1 ct. Org. Zinc

1 ct. Epoxy1 ct. 134 HG

No rusting in the scribe; nblistering, softening or

discoloration after either 3days of freshwater

immersion or 30 days of sawater immersion at 75°F

8/12/2019 Carbothane+134+HG+PDS+3 11

http://slidepdf.com/reader/full/carbothane134hgpds3-11 2/2