caoimpex drilling tools
DESCRIPTION
drilling toolsTRANSCRIPT
Drilling Tools
02
03
1Wellhead Tools
Elevatoes1.1ApplicationsElevatoes is buckled at the drill pipe joints, casing or tubing coupling below.
For hanging, hoisting and running the drill pipe, casing, or tubing tools. They
are designed and manufactured according to API Spec 8A/8C.
Elevatoes Model Representation
Type code: C side door, D center latch, B locking ring
Product code: D elevatoes
Structural characteristics of code: Z taper shoulder, square shoulder is omited
Aperture (below hole top hole), mm
Max load, KN
Elevatoe Type
SpeciesType
Side door Center latch Locking ring
Drill elevatoesSquare shoulderHalf shoulder
Taper shoulderSquare shoulderCasing elevatoes
Square shoulderTubing elevatoes
Taper shoulder
Elevatoes of the dril pipe specifications
Note: IU internal upset the drill pipe EU external upset the drill pipe IEU internal & external the drill pipe
Drill pipe elevator
drill pipe & thickening
typemm (in)
the largest diameter deill
pipe weld joints mm
Square shoulder aperture taper shoulder aperture mm Max load mm
Top hole mm Below hole mm
60.3(2 3/8)EU 65.1 59 63 67
900
73.0(2 7/8)EU 81.0 84 76 83
88.9(3 1/2)EU 98.4 102 92 101
1125101.6(4)EU
104.8 109 105
106.4 109
101.6(4)EU 114.3 118 105 121 1350
114.3(4 1/2)IU
117.5 122 118
2250119.1 121
114.3(4 1/2)EU 127.0 131 118 1333150
127.0(5)IEU 130.2 134 131 133
139.7(5 1/2)IU 144 1444500
139.7(5 1/2)IEU 144.5 149 144 148
04
05
Specifications of the drill pipe elevator
114.3(4 1/2) 117900
127.0(5) 130
139.7(5 1/2) 142
1125168.3(6 5/8) 171
177.8(7) 181
193.7(7 5/8) 197
1350219.1(8 5/8) 222
244.5(9 5/8) 248
2250273.0(10 3/4) 277
298.4(11 3/4) 303
325.0(12 3/4) 3293150
339.7(13 3/8) 344
406.4(16) 411
4500473.1(18 5/8) 478
508.0(20) 513
Casing elevator mm(in) Elevator aperture mm Max load KN
Casing elevator
Specifications of tubing elevatordrill pipe & thickening
typemm (in)
the largest diameter deill
pipe weld joints mm
Square shoulder aperture taper shoulder aperture mm
Top hole mm Below hole mm
48.3 1.9 50 50
22548.3 1.9 EU 53.0 55 50
50.3 (2 3/8) 63 63
60.3 2 3/8 EU 65.9 68 63 360
73.0 (2 7/8) 76 76 585
73.0 (2 7/8)EU 78.6 82 76675
88.9 (3 1/2) 92 92
88.9 (3 1/2)EU 95.2 98 92 900
101.6(4) 104 104
1125101.6(4)EU 108.0 110 104
114.3(4 1/2) 117 1171350
114.3(4 1/2)EU 120.6 123 117
Tubing elevator
06
07
Manual Tongs1.2Applications
Manual tongs are used to screw up or unclamp the screws of drill pipe and casing joint or
coupling. It can be adjusted by changing latch lug jaws and latch shoulder.
Manual tongs model representation
Manual tongs code
Suitable for the diameter mm
Max torque KN.m
SpecificationsType Suitable diameter mm(in) Max torque KN.m
Q86-324/75 86-324 (3 3/8-12 3/4) 75
Q3 1/2-17/90 89-432 (3 1/2-17) 90
Q340-762/35 340-762 (13 3/8-30) 35
Q80-273/35 80-273 (2 3/8-10 3/4) 35
Elevator links1.3Applications
Elevator link is a tool used to hang elevators. They have two forms: single arm & double arms.
Single & double arms model representation
Single & double mode: D single arm S double arm
Elevator mode
Max load KN
H
H
08
09
Specifications of type DH single arm elevator links
Type
Connecting sizes between elevator link lower ears and elevators
Connecting sizes between elevatoe link upper ears and drilling hooks
L(mm) Rated cap. Per set KN(t)
r1 R1 l1 l2 l3 r R2 l4 l5 l6
DH360 20 51 20 100 150 22 38 60 120 180 1200 360 40
DH585 22 51 20 100 150 22 64 70 120 180 1100 585 65
DH900 22 51 20 100 150 29 64 80 140 190 1500 900 100
DH1350 24 51 25 100 150 29 64 100 140 210 1800 1350 150
DH2250 31 70 30 140 200 35 102 140 200 250 2700 2250 250
DH3150 37 70 35 140 200 35 102 140 200 250 3300 3150 350
DH4500 48 83 50 170 250 48 121 160 240 300 3600 4500 500
DH6750 57 127 50 190 318 63 127 190 262 305 3660 6750 750
L: dimensions of recommendation. It can be changed if necessary.
Specifications of type SH double arms elevator links
Type
Connecting sizes between elevator link lower ears and elevators
Connecting sizes between elevatoe link upper ears and drilling hooks
L(mm) Rated cap. Per set KN(t)
r1 R1 l1 l2 r R2 l3 l4
SH225 15 29 20 58 22 38 35 90 600 225 25
SH360 20 5120
100 22 38 45 100 1100 360 40
SH585 22 51 20 100 22 64 65 120 1100 585 65
SH675 22 51 20 100 29 64 75 160 1500 675 75
SH900 22 51 25 100 29 64 80 160 1500 900 100
SH1350 24 51 35 100 29 64 100 160 1700 1350 150
L: dimensions of recommendation. It can be changed if necessary.
10
11
1.4 Slips
ApplicationsIt is tool used to grip and hang drilling string, there are two kind of slips: three-piece and multi-chip slips.
Model representation
Product code: W drill stem slips, WT drill collar slips, WG casing slips
Slips size code
Max load
Specifications
Diameter
in 56 /8 7 57 /8 58 /8 59 /8 310 /4 311 /4 313 /8 16 518 /8 20 24 26 30
mm 168.3 177.8 193.7 219.1 244.5 273.1 298.5 339.7 406.4 473.1 508 609.6 660.4 762
Weight
Kg 89 84 75 82 87 95 118 112 140 167 174 201 220 248
lb 196 184 166 181 192 209 260 247 308 367 383 443 486 546
Total number of segments 12 12 12 13 14 15 17 18 21 25 26 30 33 37
Type WT drill collar slips can accommodate drill
collar diameter from 41/2 in 114.3mm to 91/2in 241.3mm
Type 1WT4 / -621Wt5 / -72
3Wt6 / -81/441WT8-9 /2
Drilling collar diameter
in 14 / -6215 / -72
3 16 / -8 /4 418-9 /2
mm 114.3-152.4 139.7-177.8 171.5-209.6 203.2-241.3
Weight
Kg 49 46 42 39
lb 108 101 92 86
Max load 40 tons
Slips type DCS-S DCS-R DCS-L
Diameter
in 3-4 74-4 /814 / -62
15 / -723 16 / -8 /4 4
18-9 /218 / -102
1 19 / -11 /4 4311-12 /4 12-14
mm
76.2 101.6 114.3 139.7 171.5 203.2 215.9 235.0 279.4 304.8
101.6 123.8 152.4 177.8 209.6 241.3 254 285.8 323.9 355.6
WeightKg 51 47 54 51 70 78 84 90 116 107
lb 112 103 120 112 154 173 185 198 256 237
There are three model of DCS drill collar slips: S, R, and L. they can accommodate drill collar
from 3in (76.2mm) to 14in (355.6mm) O.D..
Casing slips can accommodate casing diameter
from 65/8 30in 168.3-762mm)
12
13
Drill slips can accommodate drill pipe from 2 3/8 to 5 1/2inch (60.3-
139.7mm) O.D.. They are classified as type short (SDS), medieum (SDML)
and extra long (SDXL) according to gripping length. SDS slips are designed
for shallow hole drilling, SDMLslips are the perfect choice for all medium
depth drilling, SDXL slips are designed for deep drilling.
Model Slips body sizes in 3 1/2 4 1/2
SDS
Pipe sizein 2 3/8 2 7/8 3 1/2 3 1/2 4 4 1/2
mm 60.3 73.0 88.9 88.9 101.6 114.3
WeightKg 53.1 50.3 48.5 64.9 61.7 57.6
lb 117 111 107 143 136 127
SDML
Pipe size
in 2 3/8 2 7/8 3 1/2 3 1/2 4 4 1/2
mm 60.3 73.0 88.9 88.9 101.6 114.3
WeightKg 87.5 85.3 81.6 94 90.3 85.3
lb 193 188 180 207 199 188
SDXL
Pipe sizein 3 1/2 4 4 1/2
mm 88.9 101.6 114.3
Weight
Kg 103.9 99.3 93
lb 229 219 205
Model Slips body size in 5 5 1/2
SDML
Pipe sizein 4 4 1/2 5 4 1/2 5 5 1/2
mm 101.6 114.3 127 114.3 127 139.7
WeightKg 92.5 88.9 84 90.9 84 82.1
lb 204 196 185 200 185 181
SDXL
Pipe sizein 4 4 1/2 5 41/2 5 5 1/2
mm 101.6 114.3 127 114.3 127 139.7
weight
Kg 107.5 103 96.6 106.1 101.5 95.3
lb 237 227 213 234 224 210
Safety clamps1.5Safety clamps is used for clamping and preventing those
non-shouldered pipes sliping from the clamp, by adjusting
the pitch number of die insert to chang the diameter range,
for handing flush joint pipe and drill collar.
SpecificationsHandling Pipe Size Weight
in mm kg lb
1 1/8-2 28.6-50.8 16.3 36
2 1/8-3 1/4 54.0-82.6 18.2 40
3 1/2-4 5/8 88.9-117.5 20.9 46
4 1/2-5 5/8 114.3-142.9 25.0 55
5 1/2-6 5/8 139.7-168.3 27.7 61
6 1/2-7 5/8 165.1-193.7 29.1 64
7 1/2-8 5/8 190.5-219.1 31.3 69
8 1/2-9 5/8 215.9-244.5 32.7 72
9 1/2-10 5/8 241.3-269.9 40.0 88
10 1/2-11 5/8 266.7-295.3 41.8 92
11 1/2-12 5/8 292.1-320.7 44.0 97
12 1/2-13 5/8 317.5-346.1 46.3 102
13 1/2-14 5/8 342.9-371.5 48.6 107
14 1/2-15 5/8 368.3-396.9 50.9 112
14
15
1.6Slip type casing elevators/spiders are tools for handing casing from 4? 14inch O.D.
Casing Elevators/spiders
SpecificationsCasing size (in)
4 1/2,5,5 1/2,6 5/8,7,7 3/4,8 5/8,8 3/4,9 5/8,9 3/4,9 7/810 3/4,10 7/8,11 7/8,13 3/8,13 1/2,13 5/8,13 3/4,14
Max load (tons/kN) 350/3150,500/4500
1.7Power tongsModel representation
Q -
Q -
Power tongs type: Z drill pipe power tongs, T casing power tongs
Tongs mode
Using the max O.D.
Max torque KN
Type ZQ drill pipe power tong1.7.1
ZQ drill pipe power tong is an ideal wellhead tool for oil drilling, widely applied in
make-up and breaking-out for well drilling and repairing on offshore and land. Open-
throat design of the ZQ series with high mobility allows escaping from drilling pipe
freely. The tong is a combination of spinning tong and torque tong. It substitutes
cathead, suspension tong and spinning rope in making-up and breaking-out. The
tongs are designed and manufactured according to API Spec 7K Specification for
drilling equipment .
SpecificationsType ZQ203-125 ZQ203-100 ZQ203-100A ZQ203-100B ZQ162-50 ZQ127-25
Size rangemm 127-203 121-203 121-203 121-203 85-162 65-127
in13 /2
coupling-8body
13 /2
coupling-8body
13 /2
coupling-8body
13 /2
coupling-8body coupling-5coupling
32 /81Coupling-3 / coupling2
32 /8
Max torquekN.m 125 100 100 100 50 25
ft.lbf 92200 73750 73750 73750 36880 18440
Speed(high gear) rpm 40 40 40 40 60 65
Speed(lower gear) rpm 2.7 2.7 2.7 2.7 4.1 10.5
Pressure rating
Mpa 20 16.6 16.6 16.6 16 12
Psi 2900 2400 2400 2400 2320 1740
Flow ratingL/min 114 114 114 114 120 180
gpm 30 30 30 30 32 48
Shiting distancemm 1500 1500 1500 1000 1000
in 59 59 59 39.4 39.4
Trave distancemm
0-1500in
0-59
Lifting distancemm 0-485 0-800
0-19 0-31.5in
sizemm 1720x1050x1750 1700x1000x1400 1700x1000x1400 1750x1650x2050 1570x800x1190 1110x790x820
in 68x41x69 67x39x55 67x39x55 69x65x81 62x31x47 44x31x32
weightkg 2600 2400 2500 3250 1500 620
lb 5730 5290 5510 7165 3310 1360
ZQ drill pipe power tong
16
17
Type TQ casing tongs1.7.2
Type TQ casing tongs are widely used for making up or breaking out pipe or
casings in dianeters of 4-13 3/8 inch. The tong heads are designed
open type and freely clamp and escape from the casing. TQ casing
tongs are safe, reliable, and easy to handle with high mobility. This tongs
can be connected to computer controlling units and can serve as ideal well
mechanical tool for surface operations in oil fields. The tongs are designed
and manufactured according to API Spec 7K Specification for drilling
equipment .
SpecificationsType TQ178-16 TQ340-20A TQ340-35 TQ178-16A TQ340-35A TQ340-50
Size rangemm 101.6-178 139.7-340 101.6-178 101.6-340 139.3-340
In 4-7 1 35 / -13 /2 8 4-7 34-13 /8
Max pressure Mpa 18 18 18 18 17.2
Psi 2610 2610 2610 2610 2494
Working flowL/min 114 114 114 114 120
Gpm 30.1 30.1 30.1 30.1 31.7
Max torque
Hi.Gear
KN.m 2.4-3 2.5-3 2.4-3 4.0-5.0 4
ft.lbf 1770-2200 1844-2200 1770-2200 2950-3680 2950
Mid gear
KN.m 6.0-7.5 11
ft.lbf 4420-5530 8103
Lo.Gear
KN.m 16 35 15-18 27-30 50
ft.lbf 11800 25800 11060-13280 19900-22120 36851
speed
Hi.Gear
rpm 54-97 60-86 54-79 80-98 72.8
Mid.Gear
rpm 21-30 27.4
Lo.Gear
rpm 9-13.1 2.6-5.3 8.5-12 12-16 5.4
Size
mm 1540X760X740 1540X900X860 1500X900X850 1560X900X850 1540X892X908
im 61X30X29 61X36X34 59X30X27 61X35X33.5 60X35X33
Weight kg 580 780 570 780 880
lb 1280 1720 1250 1720 1940
1 35 / -13 /2 8
Type TQ casing tong
18
19
1.8 Bushing
Roller Kelly bushing1.8.1
Roller kelly bushing is a necessary tool for drilling. It is to drive kelly
spinner by matching with master bushing. Through rotating of four
rollers, the friction between rollers and kelly pipe is reduced and
service life is extended. For different sizes of kelly pipe and
hexagonal pipe only need to change corresponding rollers. To
connect with rotary table, there are two transmission styles (square
and pin). The product is designed and manufactured according to
API Spec 7K Specification for Drill Equipment .
Specifications
Model Type Way of driveSuitable for kelly
Square (in) Hex. (in)
HDS
Heavy
Square drive 2 1/2-6 3-6
27-HDPPin drive
3-6 3-6
20-HDP 3-6 3-6
MDS
Medium
Square drive
2 1/2-4 1/2 3-4 1/4
RTM4 2 1/2-5 1/4 3-4 1/4
20-MDPPin drive
2 1/2-4 1/2 3-4 1/4
17-MDP 2 1/2-4 1/2 3-4 1/4
RTS4 Light-duty Square drive 2 1/2-4 1/2 3-4 1 / 4
Master bushing1.8.2
To provide the master bushings and insert bowls with the size from 171/2 371/2inch, they are with
high-quality alloy steel and the sizes conform to API Spec 7K. there are two types, pin drive and square
drive, API standard rotary slip, drill collar slip, casing slip or roller Kelly bushing can be contained in them.
SpecificationsBushing type Drive type Rotary table size (in) Handling O.D. (in)
MSS
Square drive(split body)
17 1/2 (18)
2 3/8-8 5/8
20 1/2
23
27 1/2
Square drive(solid body)
17 1/2
20 1/2
22
23
27 1/2 2 3/8-10 3/4
MSPCPin drive (solid body)
20 1/2
23
27 1/2 2 3/8-8 5/8
MDSP Pin drive (split body)
17 1/2
18
20 1/2 2 3/8-8 5/8
MSP Pin drive (split body)23
27 1/2 2 3/8-8 5/8
MPCH Pin drive 37 1/2 2 3/8-13 ¾
20
21
Casing Bushings1.8.3To provide the type CU, CUL and CB etc. casing bushing and
insert bowls, they are used to handle casing from 95/8 to
30inch O.D. they type CU and CUL are solid bushing, type CB
are split bushings.
SpecificationsRotary table
size in
Bushing type Casing size (in)
Type P/N 3 52 / -8 /8 85 39 / -10 /8 4
3 311 / -13 /4 8 16 518 / -208 24 26 30
1 117 / or20 /2 2 CU
Body And Insert
bowlBody3102and
insert180P
Body 3102 And Insert
bowl
1902
Body 3102
126 or 27 /2 CULBody 3103 And Insert
bowl 3103,180P
Body 3103 And Insert
bowl 3105,1902
Body 3103 And Insert bowl 3105
Body 3103 And Insert bowl 3104
Body3103
127 /2
CB
Body 6695 And insert
Bowl 6126, 6115
Body 6695 And insert
Bowl 6126, 6114
Body 6695 And insert Bowl 6126
Body 6695 And insert Bowl 6127
Body 6695
1 137 / or 49 /2 2
Body 20 And insert Bowl 6126, 6115
Body 20 And insert
Bowl 6126, 6114
Body 20 And insert Bowl 6126
Body 20 And insert Bowl 6127
Body 20 Body 24 Body 26 Body 30
Lifting subs1.9Lifting Subs are of one-piece construction and manufactured from alloy
steel fully heat-treated. This heavy-duty type drill collar lifting sub is
designed for use with the drill pipe elevators. The size of others are
according with API standards.
Model representation
-
TSDJ -
TSDJ
Lifting subs abbreviations of the name
Nominal size (mm)
Thread type
-
22
23
SpecificationsNo.
Normal Size mm(inch) I.D. mm Connection API
O.D. of Drill Pipe mm(inch)
O.D. of End Elevate mm
173 (2-7/8)
31.8 NC23 79.4 (3-1/8)
111.12 44.5 NC26 (2-3/8) 88.9 (3-1/2)
388.9 (3-1/2)
54 Nc31 (2-7/8) 104.8(4-1/8)
1274 50.8 NC35 120.7(4-3/4)
5 68.3 NC38(3-1/2IF 127.0 (5)
6
127.0 (5)
71.4 NC44152.4 (6)
7
158.8 (6-1/4)8
Nc46 (4IF)
158.8 (6-1/4)
9 82.6 165.1 (6-1/2)
10 171.5 (6-3/4)
11
NC50 (4-1/2)IF
177.8 (7)
12 184.2 (7-1/4)
13
NC56
196.8 (7-3/4)
14 203.2 (8)
15 95.3 6-5/8REG 209.6 (8-1/4)
16 NC61 228.6 (9)
17 7-5/8REG 241.3 (9-1/2)
18
NC70
247.7 (9-3/4)
19 254.0 (10)
20 NC77 279.4 (11)
2BitsIntroductionsAs per their structure, drill bits can be divided into drag
bits, roller cone bits, diamond bits and coring bits.
China is a major manufacturing base of bits, it is ranked
first in Asia and third in the world china owns
intellectual property rights and its technology have
reached the international advanced level. Leading in the
drill bit cutting teeth materials technology, bearing
unique structure and materials, new technology of drill
bit hydraulics, new products represent world's
development trend in the independent R & D high-
speed motor drill series, hard formation bits series and
non-standard size series.
China have advanced laboratory to test drill bits
structure and functional unit, calculated laboratory, be
able to carry out experimental evaluation of drill bits all
units including cutting structure, bearings, seals and
hydraulic systems.
Achieved from basic research, application of new
technologies, product development and manufacturing
research to product application, services and improve of
the virtuous circle, so technical reserves are backing of
the product development and marketing technology
services. They based on 3D CAD software and product
data management, throughout the life cycle of the
product to conduct a comprehensive technical
management, to make product development to achieve
fast, accurate and to maximize the timeliness and
functionality to meet market demand.
Through the application of lithology tester, Real-time
test mechanics parameters of the normal atmosphere
and confining pressure in the drilling of rock strata (such
as hardness, plastic coefficient, drillability, triaxial
compressive strength, elastic ratio and poisson's ratio,
etc.). For optimizing bit selection to provide reliable data
on formation rock properties, more accurately the type
of drill bits to provide a reasonable.
In the during use, the actual drilling time, footage,
mechanical drilling speed, hydraulic parameter, drilling
cost and other factors will affect the drilling efficiency
compared to the design estimates, and classification of
the wear assessment to improve the drill bit of the
design and lectotype.
24
25
2.1Roller cone bits
Model representationTo adopt a product feature name
Species Application
MD series MotorDigger High-speed motor bit Directional well, horizontal well,The level of branch well
MiniMD series Mini MotorDigger Slim hole drill bit Super-deep well
SMD series Super MotorDigger Super-high speed motor bit Turbine or high-speed screw downhole bit
HF series HardFighter Hard-formation bit Deep well hard formation
SWT series SwiftureHigh-performance
steel tooth bitUpper stratum
A series Air Air bit Air drilling technics
8 1/2MD517
81/ 2 MD 517
Drill bit diameter,8.5inch (215.9mm)
Series code, high-speed motor bit series
Class number, express 1ADC coding
Additional features of the code
API roller bit toleranceBit size Diameter tolerance
In In mm
3 3/8-13 3/4 0-0.0313(1/32) 0-0.79
14-17 1/2 0-0.0625(1/16) 0-1.57
17 5/8-26 0-0.0938(3/32) 0-2.38
Jet nozzle series
Size codeRoller bit size Jet diameter The length of the
nozzle assembly
in mm mm mm
1 3 3/4-5 1/2 95.3-139.7 20.30 17.48
2 5 5/8-7 3/8 142.9-187.3 23.50 19.05
3 7 1/2-8 1/4 190.5-209.6 29.74 20.62
4 8 3/8-14 5/8 212.7-371.5 32.89 26.97
5 14 3/4-26 374.6-660.4 40.84 26.97
Jet outlet diameter
mm 6 7 8 9 10 11 12 13 14 16 18 20 22 24
Lengthed, micro-long, special nozzle can be Designed according to user needs
ExampleS2-10
S 2 - 10
Standard type
For 5 5/8 to 7 3/8 bits
Jet outlet diameter (mm)
-
26
27
2.1.1MD high-speed motor bit
Horizontal well drilling technology is improved continuously, in which extended reach well
drilling technology and multilateral wells drilling technology have been developed rapidly.
The new type of MD high speed motor bit is suitable for directional well and horizontal,
high rotary speed, gage protection technology ability and stability, high reliability, well
hydraulic effect and long service life.
MD high speed motor bit is suitable for drilling with rotary speed from 300 to 90 RPM,
which is the ideal choice for directional well, horizontal well and horizontal multilateral
wells drilling.
Bit size
Code in mm
7 7/8 200.0 MD437 MD447 MD517 MD537 Md617 MD637 MD647
8 1/2 215.9 MD437 MD447 MD517 MD537 MD617 MD637 MD647 MD647
8 3/4 222.3 MD437 MD447 MD517 MD537 MD617 MD637 MD647
9 1/2 241.3 Md437 MD447 MD517 MD537 MD617 MD637 MD647
12 1/4 311.2 MD437 MD447 MD517 MD537 MD617 Md637
2.1.2MINI-MD slim hole cone bit
Increase of drilling speed is more difficult in deep well and super-deep well lower part of
the slim hole section.MiniMD slim hole cone bit has improved service life and security of
the bit, and decreased round trip times, realized the purpose of increasing drilling speed
and decreasing drilling cost. MiniMD cone bit is with the feature of MD high speed motor
bit, and designed with special bearing seal structure and oil storage system, tooth material,
cutting structure and formation lithology are matched reasonably to solve the problems of
low efficiency and tooth break.
MiniMD slim hole cone bit is the ideal choice for slim-hole section drilling in deep well and
super-deep well.
Bit size
in mmBit model
5 3/4 146.1 MD517 MD537 MD547 MD617 MD637
5 7/8 149.2 MD517 MD537 MD547 MD617 MD637 MD647
6 152.4 Md517 MD537 MD547 MD617 MD637 MD647
6 1/8 155.6 MD517 MD537 MD547 MD617 MD637 MD647
6 1/4 158.8 MD517 MD537 MD547 MD617 MD637 MD647
6 1/2 165.1 MD517 MD537 MD547 MD617 MD637 Md647
28
29
2.1.3 SUPER-MD super-high speed motor bit
The use of turbo-drill tool, with the 11 5/8inch and 8 1/ 2inch drill bits, from 400rpm to
600rpm, service life of normal cone bits is about 10 hours usually. For working situation
with super high rotary speed, drill bit used roller-journal bearing and metal-sealing,
provided bearing reliability and long life. We have also developed cutting and extended
double nozzle hydraulic structure. SMD of the service life can reaches to more than 30
hours at the work situation of above 400 RPM.
SMD is recommended to 250rpm to 600rpm, which is quite economical.
Bit size
in mmBit model
8 1/2 215.9 SMD117 SMD137 SMD417 SMD437 SMD447 SMD517 SMD537 SMD617
11 5/8 295.3 SMD117 SMD137 SMD417 SMD437 SMD447 SMD517 SMD537 SMD617
2.1.4Petroleum exploration has been developed to deep formations gradually, in deep
formations (compact plastic mudstone, lava and granite etc.,), low ROP restrict the
economic of development in deep well or super-deep well. Failure mode, such as tooth
break, tooth wear, cone tip wear and bit diameter shrink etc., usually appear when
conventional cone bits drill in hard formations. So we have developed HF series bit for hard
formations through analyze and research these failure modes deeply and make use of
advanced computer 3D simulation technology and lots of platform experiments.
Result in site shows HF series bit has the advantages of long service life, high reliability, fast
ROP and strong gage protection ability etc.. HF series bit is the ideal choice for drilling in
hard formations and strong abrasive formations effectively and safely.
Bit size
in mmBit model
HF hard-formation bit
6 152.4 HF617 HF627 HF637
6 1/8 155.6 HF547 HF617 HF627 HF637 HF737
6 1/2 165.1 HF537 HF627 HF637
6 3/4 171.5 HF537 HF617 HF627 HF637
7 7/8 200.0 HF547 HF617 HF627 HF637 HF837
8 1/2 215.9 HF537 HF547 HF617 HF627 HF637 HF647 HF737
8 3/4 222.3 HF537 HF547 HF617 HF627 HF637 HF647 HF737
9 1/2 241.3 HF537 HF547 HF617 HF627
9 7/8 250.8 HF537 HF547 HF617 HF627
12 1/4 311.2 HF537 HF547 HF617 HF627 HF637
30
31
2.1.5SWT high efficiency steel tooth bit
Abradability of teeth of conventional steel tooth cone bit is worse; tooth shape structure is
lack of optimization, which leads to decrease of average ROP. SWT series steel tooth bit
with high efficiency can solve these problems, with strong wear resistant teeth and fast
ROP, bit can work more stably, which is more suitable for drilling in soft or middle soft
formations with high rotary speed.
Application of SWT series steel tooth bit with high efficiency is the best way to solve the
problem of increasing drilling speed in higher part of well.
Bit size
in mmBit model
7 7/8 200.0 SWT116 SWT127
8 1/2 215.9 SWT116 SWT127
8 3/4 222.3 SWT116
9 1/2 241.3 SWT127
12 1/4 311.2 SWT115 SWT116 SWT127
13 3/4 349.3 SWT115
15 1/2 393.7 SWT115 SWT116 SWT127
16 406.4 SWT115 SWT116 SWT127
17 1/2 444.5 SWT115
A series air drill bit2.1.6In the water less of hard stratum, the stratum of serious leakage loss or low pressure,
in order to achieve higher drilling speed, commonly used air drilling process
technology. In the air drilling process conditions, conventional cone bit had problems
such as short service life, low ROP and weak gage protection ability etc.. Now A series
air drilling bits have solved these problems.
Bit size
in mmBit model
5 7/8 149.2 A627
6 152.4 A627
6 1/8 155.6 A627
7 7/8 200.0 A537 A617
8 1/2 215.9 A537 A547 A547
9 1/2 241.3 A537
12 1/4 311.2 A537 A547 A617
12 3/8 314.3 A537 A547
A627
32
33
2.2 Diamond bits
KM 19442.2.1Drill specifications
Size in 8 1/2
Gage length mm 85
Blade count purchase 4
Junk slot area 2mm 11087
Main cutter size mm 19
Shank 4 1/2 API Reg.
Number of nozzles purchase 4
Make up torque KN.m 16.6-23.7
Recommended drilling parameters
Rotary speed rpm 50-260
WOB KN 30 120
Flow rate L/s 25-35
Structure features and applications of the bit
Bit profile optimized design, adapted to the soft to medium
stratum.
Designs of cutting structure force balance and asymmetry
blade, make the drill bit force balanced, get better stability.
Main cutters are high performance PDC, to insure service life of
the bit while improving ROP.
Cutter exposure is optimized to insure the bit can achieve
higher ROP in soft to medium formations.
Deep junk slot design to enhance cuttings removal ability of
the bit in order to obtain high ROP.
Hydraulic system of the bit is optimized using dynamic flow
pattern simulation technology to enhance cleaning and cooling
effects of the bit to effectively prevent bit from balling.
The bit is designed with longer gage for better angle holding
ability and better stability.
34
35
2.2.2KM1952A
Bit specifications
Name Unit Parameters
Bit size in 12 1/4
Blade count purchase 5
Main cutter size mm 19
Number of nozzles purchase 7
Gage length mm 64
Shank 6 5/8 API Reg
Make up torque KN.m 49.6-51.4
Junk slot area2mm 21539
Recommended drilling parameters
Rotary rpm 50 260
WOB KN 30 140
Flow rate L/s 30 70
Structure features and applications of the bit
Bit contour optimized design, suitable to medium stratum.
Cutting structure is force balanced and bit blade is
asymmetrically designed so that the load on bit is balanced which
resulting better stability of the bit.
Multiple types of high performance PDC cutters are
strategically arranged on bit for improved service life of the bit.
Damping tooth design, the drill bit will pass through part the
hard interlayer stratum.
Hydraulic system of the bit is optimized using dynamic flow
pattern simulation technology to enhance cleaning and cooling
effects of the bit to effectively prevent bit from balling.
36
37
2.2.3Bit specifications
KS1952SG
Name Unit Parameters
Bit size in 8 1/2
Blade count Pcs 5
Main cutter size mm 19
Number of nozzles Pcs 5
Gage length mm 64
Shank API Reg 4 1/2
Make up torque KN.m 16.6-23.7
Junk slot area 2mm 12426
Recommended drilling parameters
Structure features and applications of the bit
The bit is optimally designed with medium contour which is
suitable for soft to medium soft stratum.
Cutting structure is force balanced, blade is asymmetrically
designed, spiral blade and spiral gage are designed so that the
load on drill bit is balanced, get better stability.
Multiple types of high performance PDC cutters are
strategically arranged on the bit for improved service life of the bit.
Shock absorbers are designed to make the bit capable of
drilling through formations with hard stringers.
Erosion on bit surface is effectively prevented by utilizing
hardfacing material of highly erosion resistant and applying
advanced base metal enhancement technology.
Ports on bit are also optimally designed to prevent erosion of
water courses inside the bit.
Rotary rpm 50-260
WOB KN 20 100
Flow rate L/s 25-35
38
39
Core bits3Core bit use tungsten carbide matrix with a steel skeleton in it. The bits adopt parabolic,
double cone, tapered step crown profile, and diamond inner and outer gauge.
Adapt to a variety of drilling conditions and stratum of the core drill bits, but also
according to special requirements of the site design and produce special purpose coring
drill bit series, all the core drill bit and variety of tools can form a complete set the use, with
rate fast, harvest a high rate, long life and low cost characteristics.
GC Series3.1Features
Arc crown profile, blade cutter setting.
Natural diamond ID & OD gage, fluid course set on ID gage to ensure a better cleaning
and cooling effect upon cutters of gage.
Suitable for medium hand formations. it allows to be used in a wide variety of formations.
ParameterBit size Recommended
Size TFA Gage length API CONN. Hydraulic flow rate Speed Weight on bit
in 2In in in l/s gpm rpm kN klbs
5 7/8 2 5/8 0.30-0.80 1 1/8 4 3/4 2 5/8 10-15 160-240 60-500 45-90 10-20
6 2 5/8 0.30-0.80 1 1/8 4 3/4 2 5/8 10-15 160-240 60-500 45-90 10-20
8 1/2 4 0.60-1.20 1 1/2 6 3/4 4 22-35 350-550 60-500 75-113 15-25
3.2 SC SeriesFeatures
Arc crown profile, blade cutter setting.
Natural diamond ID & OD gage.
Fluid course with ID flow or face discharge ports are optional.
Suitable for medium hand formations.
Parameter
Bit size Recommended
Size TFA Gage length API CONN. Hydraulic flow rate Speed Weight on bit
in 2In in in l/s gpm rpm kN klbs
5 7/8 2 5/8 0.15-1.00 1 4 3/4 2 5/8 6-13 100-200 60-500 23-68 5-15
6 2 5/8 0.15-1.00 1 4 3/4 2 5/8 6-13 150-250 60-500 23-68 5-15
8 1/2 4 0.20-1.50 1 1/2 6 3/4 4 22-32 350-500 60-500 45-90 10-20
40
41
Downhole tools4Drilling Jars4.1
ZSJ/ZXJ Type drilling jars (hydraulic-mechanically)
The drilling jar which is connected with drill tool and worked with drill string is a downhole
stuck freeing tool in drilling operation .It is a first selected tool for directional
well,complicated well and deep well.The drilling jar is consisting of ZSJ type drilling up jar
and ZXJ type drilling down jar,both they can be used mutually or operated separately .The
up jarring section takes use of hydraulic mechanism,the jarring force can be adjusted
according to up elevating load but can not exceed the max.load for tool load rated. The
down jarring section takes use of mechanical friction mechanism, the jarring force is well
preadjusted by adjusting device before put into downhole.No re-adjustment can be
allowed after jar is put into downhole.
According to their principle is divided into mechanical, hydraulic and hydro-mechanical
type; according to the functions can be divided into drilling up jar, drilling down jar and
drilling integrated jars type.
Thechnical specifications and parameters
Parameter\Type ZSJ80B ZXJ80B ZSJ76B ZXJ76B ZSJ70B ZXJ70B ZSJ62B ZXJ62B ZSJ56B ZXJ56B ZSJ46B ZXJ46B
O.D.(mm) 203 197 178 160 146 121
I.D(mm) 71.4 71.4 70 57 57 51
Pull down
overall length
(mm)
Up 5515 5515 5424 5360 5730 5300
Down 5250 5250 5215 5215 5000 4760
Pull down
strok (mm)
Up 368 368 344 344 332 305
Down 178 178 178 178 180 178
Connection API 6 5/8 REG 6 5/8 REG NC50 NC46 4 1/2 FH NC38
Max. tensile load (kN) 2500 2500 2300 2200 2000 1400
Max. Working Torque (N.m) 20 x 103 18 x 103 15 x 103 15 x 103 15 x 103 13 x 103
Rated release force for up jar (kN) 400~600 400~600 350~550 300~450 200~350 150~250
Max.up jarring release force (kN) 750 750 550 550 450 270
Max.down jarring release force (kN) 600 600 550 500 400 250
42
43
CSJ Type Super Fishing JarCSJ type super fishing jar is a fishing tool which the jarring force is larger than other jar
with same specification.
It features a closed structure, reliable performance, easy to adjust and easy to operate. It is
a new type of up jarring tool used in oilfield, geological exploration and drilling operation.
Thechnical specifications and parametersType Parameter CSJ44B CSJ46B CSJ62B CSJ64B CSJ70B CSJ80B
Pull-down length(mm) 4065 4065 4410 4410 4430 4430
O.D.(mm) 114 121 160 165 178 203
I.D.(mm) 38 45 57 57 60 71
Stroke(mm) 305 305 320 320 320 330
Tensile load(KN) 780 980 1270 1370 1570 1870
Max.tension downhole(KN) 340 400 700 750 800 800
Sealing pressure(Mpa) 20 20 20 20 20 20
Max. working temperature 150 150 150 150 150 150
API connection NC31 NC38 NC50 NC50 NC50 6 5/8 REG
YSJ Type Hydraulic Up JarsYSJ Type hydraulic up jar reach up jarring purpose by applying hydraulic principle and
bigelastic energy released suddenly from elastic deformed drill tool. It will obtain better
result when use with ZJS type jar extensifier.
Thechnical specifications and parameters Parameter \ Type
O.D.(mm)
I.D.(mm)
Work Stroke(mm)
API connection
Max. work torque (kN.m)
Max. jarring lifting tons (tf )
Sealing pressure (MPa)
Max.work temperature
YSJ114B YSJ121B YSJ159B YSJ178B YSJ203B
114 121 159 178 203
38 38 57 57 70
289 290 380 380 390
4.9 7.8 151 9.6 23.5
200 300 710 750 800
20 20 20 20 20
150 150 150 150 150
NC31 NC38 NC50 NC50 6 5/8 REG
44
45
ZJS Type Jar IntensifierThe ZJS type jar intensifier is a down hole fishing jar designed to increase jarring energy to
up jar .Therefore ,it must be run in conjunction with CSJ type super jar or YSJ type hydraulic
up jar .Its function mainly is to supply acceleration to the upper end of the jar during the
free jarring stroke .With a special function ,the intensifier is essentially a fluid spring which
not only can accelerate the up jarring action but also make the jarring action directly to
strike on the fish and reduce damages to the drill tool and fishing tool .
Thechnical specifications and parametersParameter \ Type
O.D.(mm)
I.D.(mm)
Overall length of pull down (mm)
stroke(mm)
Connection
Max. tensile load downhole (KN)
Sealing pressure MPa
Pull down Full stroke force (tf)
ZJS114B (ZJS44B) ZJS121B (ZJS46B) ZJS146B (ZJS56B) ZJS159B (ZJS62B) ZJS178B (ZJS70B) ZJS203B (ZJS80B)
114 121 146 159 178 203
38 38 51 57 57 71
3340 3340 4000 4500 4000 4010
250 250 330 330 310 330
NC31 NC38 NC40 NC50 NC50 6 5/8 REG
800 900 1200 1500 1800 2200
20 20 20 20 20 20
25-30 30-35 35-40 60-65 75-85 62-67
DJ Type Surface Bumper JarThe DJ Type Surface Bumper Jar is an effective tool for resolving the problem of stuck drill
tool in down hole.It is connected with the surface section of drill string, the device to
adjust the tonnage shall protrude from the rotary disc face, the violent down jarring to the
stuck catch can be clearly seen when the surface jar makes jarring operation. The jarring
strength for the tool can be easily adjusted and it is a easy operated, unique designed tool
which can make continuous down jarring .The surface jar, which not only can bear heavy
load and strong torque but also owns a good sealing property and can withstand the mud
circulation with high pump pressure, has proven to be an safe, successfully effective
releasing tool through many years application.
Thechnical specifications and parameters
Type/Parameter
O.D. mm (in)
Max. Jarring force MN (tf )
Max. Tension Load MN (tf )
Sealing Pressure Mpa (kgf/cm2)
Stroke mm (in)
I.D. mm (in)
Connection
Closed Length mm (in)
DJ46B(4 3/4") DJ70B(7")
121(4 3/4) 178 (7)
0.4(41 +- 5) 0.8 (80 +- 5)
1.2(122) 1.5 (153)
20(196) 20(196)
1500 (59) 1220 (48)
32(1 1/4) 51(2)
NC38 (3 1/2 IF) NC50 (4 1/2 IF)
3155 (124.2) 3090 (121.8)
46
47
The fishing bumper sub is a kind of mechanical down jarring tool with long wrking stroke.
It can jar stuck pipe stem repeatedly to loose stuckpoint to release stuck pipe.
Thechnical specifications and parametersParameter \ Type
O.D.(mm)
I.D.(mm)
KXJ Type Fishing Bumper Subs
Sealing pressure (MPa)
Max.tensile load (tf)
Work stroke (mm)
Connection
Closed length (mm)
KXJ44B KXJ46B KXJ56B KXJ62B KXJ70B KXJ80B
114 121 146 159 178 203
38 38 51 51 70 70
20 20 20 20 20 20
112 122 132 143 153 163
1000 1000 1200 1400 1400 1500
NC31 NC38 NC40 NC50 NC50 6 5/8 REG
2100 2110 2300 2600 2650 2740
BXJ Type Lubricated Fishing Bumper SubsThe BXJ Type Lubricated Fishing Bumper Sub is a mechanical down jaring tool whose all
moving parts are bathed in closed chamber to enjoy long service life.It is suitable for using
in deep hole and middle deep hole.
Thechnical specifications and parameters
Parameter \ Type
O.D.(mm)
I.D.(mm)
Sealing pressure (MPa)
Max.tensile load (tf)
Work stroke (mm)
Connection
Closed length (mm)
BXJ62B BXJ70B
159 178
57 70
20 20
143 153
460 465
NC50 NC50
2730 2950
48
49
4.2Shock Absorber Type SJ should be connected with the drilling string close to the bit. It can
reduce or absorb both longitudinal and circumferential vibration of the drilling string in
drilling operations. It can achieve the optimum combination of drill pressure and drill
speed, reduce the drilling cost and promote the drilling efficiency.
Shock absorbers
SJ Type Shock Absorber
TYPE O.D.in (mm) I.D.in (mm) Tool Joint Connection API
Max. Tensile Load Lbf (N)
Max. Drill Pressure Lbf (N)
Max.Working Torque Lbf-ft
(N?m) Max. Stroke
in (mm) Ambient
Temperature
Overall Length Extendedft-in (mm)
SJ46 4-3/4 (121) 1-1/2 (38) NC35220,320
(980,000) 67,440
(300,000) 7,370
(10,000) 4(100)
-40 +150
13 10(4,208)
SJ62 6-1/4(159) 1-7/8(47) NC46337,230
(1,500,000) 76,430
(340,000) 10,840
(14,700) 4-3/4 (120) 18 1(5,510)
SJ70 7(178) 2-1/4(57) NC50337,230
(1,500,000) 76,430
(340,000) 10,840
(14,700) 4-3/4 (120) 20 4(6,210)
SJ80 8(203) 2-1/2(65) 6-5/8REG449,640
(2,000,000) 98,920
(440,000) 14,450
(19,600) 4-3/4(120) 18 6(5,641)
SJ90 9(229) 2-13/16(71) 7-5/8REG562,050
(2,500,000) 121,400
(540,000) 14,450
(19,600) 4-3/4 (120) 19 4(5,902)
SJ100 10(254) 2-13/16(71) 8-5/8REG 629,490
(2,800,000) 121,400
(540,000) 18,060
(24,500) 4-3/4 (120) 21(6,400)
SJ110 11(279) 2-13/16(71) 8-5/8REG 674,460
(3,000,000) 121,400
(540,000) 21,680
(29,400) 4-3/4(120) 18 4(5,580)
YJ Type Hydraulic Shock AbsorberHydraulic Shock Absorber Type YJ should be connected with the drilling string close to the
bit. It can absorb or reduce axial vibration and thrust load of the drilling string, and have a
good result for prolonging the service life of the bit and protecting the drilling tools as well
as the surface equipment.
TYPE O.D.in (mm) I.D.in (mm) Tool Joint Connection API
Max. Tensile Load Lbf (N)
Max. Drill Pressure Lbf (N)
Max.Working Torque Lbf-ft
(N?m) Max. Stroke
in (mm) Ambient
Temperature
Overall Length Extendedft-in (mm)
YJ46
YJ62
YJ70
YJ 80
YJ 90
4-3/4(121) 1-1/2(38) NC38220,320
(980,000) 9,570
(265,000) 7,370
(10,000) 4(100)
-40 +150
13 6(4,116)
6-1/4(159) 1-7/8(47) 4-1/2REG337,230
(1,500,000) 76,430
(340,000) 10,840
(14,700) 5(125) 14 8(4,476)
7(178) 2-1/4(57) NC50337,230
(1,500,000) 76,680
(350,000) 10,840(14,700) 5(125) 12 3
(3,745)
8(203) 2-5/8(68) 6-5/8REG449,640
(2,000,000) 110,160
(490,000) 14,450
(19,600) 5-1/2(140) 13(3,945)
9(229) 2-13/16(71) 7-5/8REG562,050
(2,500,000) 119,150
(530,000) 14,450
(19,600) 5-1/2(140) 12 9(3,885)
50
51
4.3Cross-over SubCross-over sub acts for conversion and connection of drill stem component in petroleum
,natural gas and geology drilling work.It is used mainly for connecting of upper drill tools
and lower drill tools during drilling operations.
The cross over sub in 3 types of main structure
Sort Description Upper Connection Part Lower Connection Part Type
1 Kelly cross-over sub Kelly Drill pipe A or B
2 Drill pipe cross-over sub Drill pipe Drill pipe A or B
3 Interim cross-over sub Drill pipe Drill collar A or B
4 Drill collar cross-over sub Drill collar Drill collar A or B
5 Drill bit cross-over sub Drill collar Drill bit A or B
6 Swivel cross-over sub Swivel lower sub Kelly C
7 Fishing cross-over subKelly Drill pipe C
Drill pipe Fishing tools C
Type A stand for same diameter: one crossover sub has one size (D) on O.D., code A.
Type B stands for reduce type: one crossover sub has two sizes (D1, D2) on O.D., code B.
Type C is left hand thread type: the connection thread is left hand type, code C.
5Directional tools
5.1StabilizerIntegral spiral blade stabilizerIntegral 3-Spiral Blade Stabilizer, Integral 4-Spiral Blade Stabilizer (string type, near bit type ).
The working hardfacing surface (also called as wall contact )materials available separately
are (1) carbide insert,(2) Inserted diamond compound, (3) Low temperature brazing
tungsten carbide slug,(4) Surface bead welding abrasive welding rod, etc.
Technical specifications and parameters
52
53
Bit size(in) Working O.D. End O.D. Of body I.D. Length
Thread code on both ends
String type Near bit type
Top Down
6 152.2
121 51 1200 NC38 3 1/2 REG 6 1/4 158.7
6 1/2 165.1
7 1/2 190.5159 57 1600 NC46
4 1/2 REG
7 7/8 200
8 3/8 212.7159165
71
16001800
NC46
NC508 1/2 215.2 1591651788 3/4 222.2
9 1/2 241.3
178
197
1600
NC50 NC50 NC50 6 5/8 REG 9 5/8 244.51800
9 7/8 250.8
12 1/4 311.2 203229
76
1800NC566 5/8 REG Nc56 6 5/8 REG Nc56 6 5/8 REG 6 5/8 REG
16 406
229
241.320002200
NC617 5/8 REG NC617 5/8 REG NC617 5/8 REG NC617 5/8 REG
17 1/2 444.5
24 609.6
26 660.4
28 711.2
Top Down
Replaceable sleeve spiral stabilizerThe replaceable sleeve stabilizer are available with two-piece and three-piece construction. The three-
piece construction stabilizer is made of a body and a centralizing body(refer to sleeve replaceable). The
advantage is that the sleeve can be changed quickly and easily after sleeve hardfacing is worn-out. This
kind of stabilizer is especially suitable for working in directional well .
Tec hnical parameters for 2-piece replaceable sleeve stabilizer
Bit Dia.(In)
Drill collar
dia.(in)
Stabilize sleeve The body Thread code on both ends
Length Work O.D.
Upset end Dia.
upset end
length
Fishing neck
length ID
Make-up Torque (KN.m)
Over length L Drill string type
Near bit type
Near bit Type
Drill String Type
Top Down Top Down
8 1/2
6 1/2
480 214
190
200 600
71 6.95~7.25 1800~1900 1800~19004
1 / 2 IF
41 / 2
IF
41 / 2
IF
41 / 2 REG
8 1/4 470 210
8 472 203
7 3/4 455 197
12 1/4
8
555 310
238
76
19.7~11 1800~2000 1800~20006
5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
12 550 305
11 1/2 540 292
11 530 279
17 1/2
9
682 444
279
13.85~16.557
5/8 REG
7 5/8 REG
7 5/8 REG
7 5/8 REG
17 676 432
16 1/2 670 420
16
644 40722
24
26
2000~2200 2000~2200
54
55
5.2Directional bend sub is a mainly deflecting tool with screw drill. The screw drill bring to
bear sideforce on bit,The bit cut borehole wall side continue.The well track will be curve.
Directional Bend Sub
Technical ParameterType Sinuosity thread
DWWJT121 1-2.5 NC38 3 1/2 REG
DWWJT127 1-2.5 NC38 3 1/2 REG
DWWJT159 1-2.5 NC46 4 1/2 REG
DWWJT165 1-2.5 NC46 4 1/2 REG
DWWJT178 1-2.5 NC50 4 1/2 REG
DWWJT197 1-2.5 5 1/2FH 5 1/2 FH
Cementing Tools6Drilling liner hanger is a specialized cementing tool which can suspend
liner and cement in the pipe.
Specifications
TypeHunger Casing O.D. Of
tail pipe(mm)
ConnectionO.D.(mm) I.D.(mm) well thickness(mm)
XG-7 5
XG-7 5/8 5
XG-7 5/8 5 1/2
XG-8 5/8 5 1/2
XG-9 5/8 5 1/2
XG-9 5/8 7
XG-13 3/8 9 5/8
152
165
165
195
214
214
298
108
108
122
122
122
155
223
178
194
194
219
244
244
340
11.51 10.36 9.19
12.70 10.92 9.52
11.43 10.16
11.43 10.16
11.99 11.05 10.03
11.99 11.05 10.03
12.19 10.95 9.65
127
127
140
140
140
178
244
NC38
NC38
NC38
NC50
NC50
NC50
Nc50
O.D.(mm)
Drilling liner hanger6.1
56
57
Float coupling or casing float shoe is name of casing guide shoe or coupling which can produce buoyancy.
6.2Float Coupling and Casing Float Shoe
Specifications
Type O.D. (mm)Length (mm) connection
Type of cement filling
Type of non-cement filling Box thread Pin thread
FG127
FX127
FG140
FX140
FG140
FX140
FG168
FX168
FG178
FX178
FG194
FX194
FG219
FX219
FG245
FX245
FG273
FX273
FG340
Fx340
141
154
188
195
216
244.5
270
298.5
324
365
450-550
550-650
600-700
800-900
300-500
Long circle
(or on the request of user)
Short circle
(or on the request of user)
Long circle
(or on the request of user)
Short circle
(or on the request of user)
Casing centralizer6.3Casing centralizer is a facility to maintain the casing at the well's center; it can also reduce the
resistance during running casing and avoid sticky casing, help to improve the quality of
cement ring cementation.
There are rigid and spring centralizers.
Parameters of the spring centralizer
Parametrs of rigis centralizer
Size mm Starting force N Return force N
114.3
127
139.7
177.8
244.5
339.7
1027
1872
1659
3695
5057
5422
2328
3114
3014
7330
8013
5881
Size mm Centralizer O.D.mm
114.3
127
139.7
177.8
244.5
151
151
210/212/215
210/212/215
314
58
59
Stage cementing equipment is to achieve two-stage or multistage continuous or uncontinuous injection of
cement operations, is installed in the predetermined position of the casing string a special facility.
By stage coupling body, lower rubber plug, open and close plug component.
6.4 Stage cementing equipment
ParametersSize mm
Max. O.D. mm
Orifice mm
Length mm
Rated load t
Seal pressure MPa
Open pressure MPa
Close pressure MPa
Lower sliding bush ID. mm
Upper sliding bush ID. Mm
139.7
170
122
1082
140
25
7
5
85
95
177.8
208
155
1182
170
25
7
5
115
125
244.5
283
220
1222
210
25
7
5
176
197
According to connect thread, cement is divided into drilling
pipe cement joint and casing cement joint. Drilling pipe
cement joint connect with drill at the wellhead, casing
cement joint connect with casing.
Casing cement joints are divided into single-and dual-plug
cement.
6.5 Cement heads
Parameters of drilling cement joint
Parameters of single-plug cement
Size mm O.D. mm ID. mm Length mmLength of
accommodate plug mmWorking pressure Mpa
89 89 70 1000 300 35
127 127 108 1000 350 35
Size mm
O.D. mm
ID. mm
Totall length mm
Length of accommodate plug mm
Form of backing pin
Working pressure Mpa
127
157
112
1000
320
Single
30
139.7
170
121
177.8
208
157
244.5
275
222
273
303
248
339.7
370
320
1300
340 350 550 550 660
Dual Dual Dual Dual Dual
25
60
61
Parameter of dual-plug cementSize mm
O.D. mm
ID. mm
Totall length mm
Length of accommodate
plug mm Second
Fom of backing pin
Working pressure Mpa
First
127
157
112
1300
250
320
Single
139.7
170
121
255
340
177.8
208
157
310
350
Dual
244.5
275
222
1700
460
500
DualDual
273
303
248
460
500
339.7
370
320
460
500
Dual Dual
30 25
Well-control Equipment7
Blowout preventer7.1
Model description
Product code; FH ring of spherical rubber core, FHZ ring of cone rubber core,FZ single-ram, 2FZ dual-ram, 3FZ three-ram, SFZ manual ram
Orifice code
Rating working pressure Mpa
62
63
7.1.1Annular blowout preventer
Annular BOP has two kinds of structure; they are cone-shaped
and spherical-shaped rubber core. Top cap and shell use bolt and
claw block connect two forms.
Spherical rubber core annular BOP consist of top cap, shell, piston,
spherical rubber core and scraper seal.
Cone rubber core annular BOP consists of top cap, wear-resisting
plate, shell, piston, cone core, scraper seal and support tube.
Parameters of cone core annular BOP
Orifice mm Working pressureMPa close capacity L open capacity L
179.4
279.4
346.1
425.4
539.7
70
70
70
35
14
36
67
116
134
95.3
27
66
117
134
94.5
Parameters of spherical annular BOP
Orifice MPaWorking
pressure MPaClose capacity
LOpen capacity
L
Profile size mmTotal weight
kgA B
179.4
228.6
279.4
346.1
425.3
527.0
539.7
21
35
21
35
21
35
21
35
35
21
35
21
21
34
42
50
60
94
94
220
173
241
15
15
22.8
33
39
72
69
69
171
110
181
745
745
902
1016
1014
1146
1271
1271
1683
1375
2240
769
797
838
860
870
1110
1105
1150
1558
1293
1718
1433
1520
2398
2986
2950
4675
5738
6415
16000
6994
20230
64
65
7.1.2 Ram BOPRam BOP according to ram number of set can be divided into: single, dual and three ram
BOP.
Switch mode: hydraulic and manual
Lock method: manual and hydraulic lock
Side door switch mode: rotating and line movement side door
ParametersOrifice in Working pressure MPa Lock method Connection method
7 1/16-26 3/4 21/35/70 Manual/Hydraulic Screw/Flange
Choke & kill manifold7.2Choke manifold7.2.1
The choke manifold is support equipment of hydraulic BOP for controlling well
blow out and well pressure. Through the choke valve, perform well killing,
replacing polluted slurry in well.
Control wellhead pressure of casing and standpipe, restoring mud to control
pressure at well bottom to stop overflow.
Through relief pressure, decrease wellhead pressure to perform Flexibility Shut
off Well .
Through drain valve, decrease casing pressure of wellhead to protect BOP stack.
Furnished with hydraulic control pod to achieve the function of remote control
Working pressure: 2000PSI 20000PSI
Nominal Bore: 2.1/16" 4.1/16"(46mm 103mm)
Working Medium: oil, natural gas, mud
Working Temperature: -46 C 121 C Class Lu
66
67
7.2.2When full ram seals well, inject weighted mud into well bore to perform well killing
When well blowout occurred, inject water into well through kill manifold to prevent be on fire.
When the well is on fire, inject extinguishing agent into well bore through kill manifold to put out fire.
Kill manifold
Working pressure: 2000PSI 20000PSI
Nominal Bore: 2.1/16" 4.1/16"(46mm 103mm)
Working Medium: oil, natural gas, mud
Working Temperature: -46°C 121°C Class Lu
Drill-stem inside blowout tools7.3
7.3.1Upper, lower Kelly valve
The kelly cock valve ,which is a manually operated ball valve run in the I.D of drill string ,is one of
effective tool for preventation from blowout .The kelly cock is divided into upper kelly cock valve and
lower kelly cock . The upper kelly cock is connected between lower end of swivel and upper end of kelly.
The lower kelly cock is connected between upper end of drillpipe and lower end of kelly or connected
between lower end of kelly saver subs. The kelly cock features a simple operation, the kelly cock can be
opened on or closed off by only turning the special operating spanner at 90 degrees according to
indicating direction.During drilling operation,in order to avoid serious well kick or blowout accident, the
kelly cock shall be connected at upper end and lower end of kelly.
68
69
Upper Kelly Cock
Type O.D. (mm) Thread connection (LH) I.D. (mm) Max.sealing pressure
(Mpa)
CS 146
CS 200
146
200
4 1/2 REG
6 5/8 REG
50
76.2
68.6
68.6
Lower Kelly CockType O.D. (mm) Thread connection I.D. (mm) Max.sealing pressure
(Mpa)
XS105
XS121
Xs127
XS165
Xs178
105
121
127
165
178
NC31
NC38
NC38
NC46
NC50 , 5 1/2FH
41.3
50
50
61
71.4
68.6
68.6
68.6
68.6
68.6
7.3.2It is an inside BOP (blowout preventer)in the drill string.It is simple in structure and easy to
operate.When blowout is going to be happened,the thread connections of the Kelly are
screwed out immediately and the back pressure valve is put into the I.D. of drill pipe and then
pumped downward to the required place.Thus the blowout accident can be prevented.The
tool is consisting of landing sub and check valve assembly.The landing is thread connected
with stop ring and tightened on and put into downhole with drill string .The landing sub is
used as a sub above drill string before check valve is run in downhole.
Drop-in check valve
Technical specifications and parameters
Specification
Check Valve Assembly Valve Sub Stop Ring Seal Pressure
(Mpa)Connection API
O.D. (mm) O.D. (Mm) I.D. (Mm)
FT89
FT105
FT121
FT159
FT168
FT178
Ft203
33
36
54
58
68
68
68
89
105
121
159
168
178
203
30
33
50
54
64
64
64
35(70)
NC26
NC31
NC38
NC46
NC50
5 1/2 FH
6 5/8 REG
70
71
7.3.3Arrow type check valve
FJ Type-Arrow Back Pressure Valve is an important tool in preventing of
blowing out in drilling operation. Comparing to other structural valves, it
possess some advantage such as high strength, big flowa area, high
temperature resistant, high pressure resistant, and easily maintenance.
Technical specifications and parameters Type O.D. (mm) I.D. (mm) Connection Working Pressure(MPa)
Fj229
FJ203
FJ178
FJ168
FJ165
FJ159
FJ121
FJ105
Fj89
229
203
178
168
165
159
121
105
89
7 5/8 REG
6 5/8 REG
5 1/2 FH
NC50
NC50
NC46
NC38
NC31
Nc26
82
82
82
82
82
70
56
44
33
70(35)
70(35)
70(35)
70(35)
70(35)
70(35)
70(35)
70(35)
70(35)
8 Incident handing tools
Taper taps8.1The taper tap is a special fishing tool making thread in tube dropped object such as drill
pipe and oil tube.The taps are turned from high trength alloy steel forging materials and
heat treated.It is made with chip groove so as to make threads.The box tap is a special
external fishing tool which is engaged on the outside wall of tubing objects such as oil
tubing and drill pipe.
Technical specifications and parametersType I.D. (Mm) Connection Catch size (mm)
GZ86-1
GZ86-2
GZ95-1
GZ105-1
GZ105-2
GZ105-3
GZ105-4
GZ105-5
GZ121
GZ121
Gz121
NC26
NC26
NC26
NC31
NC31
NC31
NC31
NC31
NC38
NC38
Nc38
16
20
25
20
25
15
25
8
16
20
20
39~67
54~77
68~89
54~77
72~90
43~87
76~100
30~76
45~67
55~89
88~103
72
73
Die collars8.2Die Collars is a special fishing tool making thread in tube dropped object such as drill pipe and oil
tube.The taps are turned from high trength alloy steel forging materials and heat treated.It is made with
chip groove so as to make threads.The box tap is a special external fishing tool which is engaged on the
outside wall of tubing objects such as oil tubing and drill pipe.
Technical specifications and parametersType Connection Catch size (mm)
MZ-NC26
MZ-NC26
MZ-NC26
MZ-NC31
MZ-NC31
MZ-NC31
MZ-NC38
MZ-NC38
MZ-NC50
MZ-4 1/2FH
MZ-5 1/2FH
MZ-6 5/8REG
NC26
NC26
NC26
NC31
NC31
NC31
NC38
NC38
NC50
4 1/2FH
5 1/2FH
6 5/8REG
41~52
50~68
62~80
69~73
71~82
76~95
86~108
95~118
110~135
114
141
168
Releasing and circulating overshots8.3
The releasing overshot is the special external fishing tool used for fishing drilcollar, drill pipe, oil tube
and other fishes in drilling and work over operation .
Type O.D.(mm)Max.catch size (mm)
Connection API
Type O.D.(mm)Max.catch size (mm)
Spiral grapple
Basket grapple
Connection APISpiral
grappleBasket
grapple
LT-T89
LT-T92
LT-T95
LT-T102
LT-T105
LT-T114
LT-T117
LT-T127
LT-T143
LT-T152
LT-T168
LT-T168B
LT-T181
89
92
95
102
105
114
117
127
143
152
168
168
181
60.3
73
76.2
73
85.7
89
89
95
120.6
128
127
139.7
146
47.6
63.5
66.6
60.3
73
75
78
80
102
111
114
120.6
127
NC26
NC26
NC26
NC26
NC31
NC31
NC31
NC38
NC38
NC38
NC50
NC50
Nc50
LT-T194
LT-T200
LT-T206
LT-T206A
LT-T219
LT-T232
LT-T244
LT-T260
LT-T270
LT-T273
LT-T286
LT-T298A
LT-T340
194
200
206
206
219
232
244
260
270
273
286
298
340
159
159
178
168
178
203
206
219
228.6
241.3
244.5
257
286
141
141
163
152
159
187
184
200
209.6
216
225.4
238.1
260
NC50
NC50
NC50
NC50
NC50
NC50
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
74
75
8.4In drilling and work over opertion,the releasing spear is a tool mainly used for fishing of drill pipe,oil
pipe and casing from fish hole.It can be used with internal cutter ,bumper jar etc.
Releasing spears
Technical specifications and parametersType Mandrel O.D (mm) Catch size (mm) Connection Allowed Load (KN)
LM-T60
LM-T73
LM-T89
LM-T102
LM-T114
LM-T127
LM-T140
LM-T168
LM-T178
LM-T194
LM-T219
LM-T245
LM-T273
LM-T340
89
105
105
105
105
121
121
162
162
165
203
203
203
203
47.4-51.8
57.4-62
70-77.8
82-90.1
92.4-103.9
102-115.8
118.6-127.3
140-153.7
150.4-166.1
168.3-178.5
190.8-205.7
216.8-228.7
240-258.9
313.6-323
NC26
NC31
NC31
NC31
NC31
NC38
NC38
NC50
NC50
NC50
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
270
380
650
800
1000
1300
1500
2200
2200
2300
2300
2500
2500
2500
Reverse circulation fishing magnets8.5
CLF type fishing magnet in petroleum and geology exploration is used for fishing of small fallen objects in the down
hole.With some of advantages such as simply structure, easy to operate, reliable performance, small size and
lightweight,it is equipped with permanent magnet iron which can attract small objects such as teeth wheel, palm,
tong teeth and tool so that small objects in down hole are fished and the well bottom is cleaned up.
Technical specifications and parametersType O.D. (mm) Connection
Attracted Weight
2(kg/cm ) Temperature
in wellHole Size (mm)
CLF89
CLF100
CLF125
CLF140
CLF146
CLF150
CLF175
CLF178
CLF190
CLF200
CLF203
CLF225
CLF254
CLF265
CLF292
CLF317
CLF356
89
100
125
140
146
150
175
178
190
200
203
225
254
265
292
317
356
NC26
NC26
NC38
NC38
NC38
NC38
NC50
NC50
NC50
NC50
NC50
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
7 5/8 REG
7 5/8 REG
9.8
9.8
9.8
8.5
8.5
8.5
7.9
7.8
7.8
7.6
7.6
7.5
7.0
6.9
6.9
6.9
6.9
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
95~110
110~135
135~165
150~175
160~185
160~185
185~210
185~210
200~225
210~235
215~240
235~270
265~311
275~330
300~442
340~375
444.5
76
77
8.6The LL-F type reverse circulation junk basket is used to retrieve all types of small junk objects such as
cone,cutter,hand tool and junks from the bottom hole.During drilling operation,it produces a local
reverse circulation of fluid at well core so as to effect a complete recovery of junk in the junk basket
.Especially when PDC bit is used ,cleaning bottom well by the tool becmes very necessary to ensure the
bit with a normal application.The reverse circulation junk basket therefore becomes an essential tool in
oil ,geology exploration and drilling engineering.
Reverse circulation junk baskets Technical specifications and parameters
Type Barrel O.D. (Mm)
Mill Shoe O.D. (mm)
Max.Fish O.D. (Mm) Ball Dia. (mm) Connection Hole Size
(mm)
LL-381
LL-318
LL-F286
LL-F279
LL-F254
LL-F245
LL-F232
LL-F206
LL-F195
LL-F178
LL-F168
LL-F130
LL-F121
LL-F114
LL-F97
LL-F89
381
318
286
279
254
245
232
206
195
178
168
130
121
114
97
89
386
324
292
286
260
252
239
210
202
184
174
136
126
121
103
94
282
248
217
211
195
192
179
159
149
130
123
94
90
82
62
55
55
55
55
55
55
50
50
45
42
42
42
40
35
35
30
30
7 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
6 5/8 REG
NC50
NC50
NC50
NC50
NC50
NC50
NC31
NC31
NC31
NC26
Nc26
406-444
349-406
320-346
300-341
275-295
275-295
255-270
223-241
215-241
198-209
190-209
155-165
142-152
130-140
117-127
108-114
78
79
8.7Reversing sub is also called reversing spear which is a special tool for reversing
stuck drill stem above stuck point in drilling and work over operation. When make
fishing or reversing, if fallen object is stuck or fail to be released, the tool can
released from thread connection of reversing sub to take out fishing tool.
Reversing subs
Technical specifications and parameters
Type Tool O.D. (mm) Connection (LH) Connection (RH)
DKJ105
DKJ121
DKJ165
DKJ165
DKJ165
DKJ165
DKJ178
DKJ203
DKJ203
105
121
165
165
165
165
178
203
203
NC31
NC38
NC50
NC50
NC50
NC50
NC50
NC50
Nc50
NC31
NC38
NC46
NC50
5 1/2FH
NC56
6 5/8REG
NC61
7 5/8REG
8.8The mechanical internal cutter is a special tool to cut pipe in pipe string. With
exception of coupling, it can cut at any position of fish. During cutting
operation,the releasing spear can be connected above internal cutter, after finish
cutting,pipe string above cutting position can be lifted out at a time.
Mechanical internal cutters
Technical specifications and parametersType Tool O.D. (mm) Connection Pipe String I.D. (mm) Pipe string O.D. (In)
ND-J114
ND-J127
ND-J140
ND-J168
ND-J178
ND-J245
91
102
112
138
145
210
NC26
NC26
NC31
NC38
NC38
Nc50
97-104
107-115
118-128
144-153
150-166
216-228
4 1/2
5
5 1/2
6 5/8
7
9 5/8
80
81
8.9Mechanical external cutter is a special tool to cut casing, tubing and drilling pipe in pipe string.
Mechanical external cutters
type O.D. ID. Pipe O.D. Max fallen object O.D.
Connection screw Well ID.
WD-J58
WD-J98
WD-J114
WD-J119
WD-J143
WD-J149
WD-J154
WD-J194
WD-J206
58
98
114
119
143
149
154
194
206
41
79
82
98
111
117
124
162
168
33.4
60
60
73
52 89
60 89
60 101
89 101114 127
101 146
39.4
78
79
95
108
114
120
159
165
2 3/8 TBG
2 3/8 TBG
NC26
NC26
NC31
NC31
NC38
6 5/8 REG
6 5/8 REG
62.0
105.0
120.6
125.4
146.2
155.6
158.8
209.5
219.0