build your own battery tester nsf spirit workshop 2008
TRANSCRIPT
Build Your Own Battery Tester
NSF SPIRIT Workshop2008
Build Your SkillsToday’s OBJECTIVES:
Learn to Solder.Examine how circuit components work in a
simple circuit that is used to test a battery.Gain exposure to the fundamental law of
circuit design – Ohm’s Law.Build the circuit in lab. Take it with you!
Light Emitting Diodes (LEDs)
A diode is a semiconductor electronic device.
Form numbers on digital clocks, Transmit information from remote controls, Tell you when appliances are turned onForm images on a jumbo television screen or illuminate a
traffic light.
A semiconductor is a material with varying ability to conduct electrical current Reference: http://electronics.howstuffworks.com/led1.htm
Semiconductor BasicsSemiconductors are
made from a poor conductor that has had impurities (atoms of another material) added to it. This process is called doping.
When these two materials are joined, a P-N Junction is formed.
A semiconductor with extra electrons is called N-type material, since it has extra negatively-charged particles.
A semiconductor with extra holes is called P-type material, since it has extra positively-charged particles.
At a P-N Junction, electrons can jump from hole to hole, moving from a negatively-charged area to a positively-charged area. The holes appear to move in the opposite direction. This Flow of Charge is called Current!
A diode comprises a section of N-type material bonded to a section of P-type material, with electrodes on each end. This arrangement conducts electricity in only one direction. When no voltage is applied, to the diode, electrons from the N-type material fill holes from the P-type material along the junction between the layers, forming a depletion zone. In a depletion zone, the semiconductor material is returned to its original insulating state -- all of the holes are filled, so there are no free electrons or empty spaces for electrons, and charge can't flow.
The Diode: a tiny “P-N Junction”!
To get rid of the depletion zone, you have to get electrons moving from the N-type area to the P-type area and holes moving in the reverse direction. To do this, you connect the N-type side of the diode to the negative end of a circuit and the P-type side to the positive end. The free electrons in the N-type material are repelled by the negative electrode and drawn to the positive electrode. The holes in the P-type material move the other way. When the voltage difference between the electrodes is high enough, the electrons in the depletion zone are boosted out of their holes and begin moving freely again. The depletion zone disappears, and charge moves across the diode.
Ah-hah! Let’s put a Battery to it!
What happens if we Reverse it?
If you try to run current the other way, with the P-type side connected to the negative end of the circuit and the N-type side connected to the positive end, current will not flow. The negative electrons in the N-type material are attracted to the positive electrode. The positive holes in the P-type material are attracted to the negative electrode. No current flows across the junction because the holes and the electrons are each moving in the wrong direction. The depletion zone increases.
The interaction between electrons and holes in this setup has an
interesting side effect -- it generates light!
HOW Does a Diode produce light?
SummaryA Diode is a common component in many
electronic applications. A Diode is a P-N junction that allows current
to pass in only one direction, under the right conditions.
Light-emitting diodes, or LED’s emit light when current is flowing across the diode.
Battery Tester Use a LED to build a circuit that will show a
good battery from a bad battery.
Connected Correctly, A Good Battery will Light up the LED!
+ DIODE -
Let’s Design the CircuitOHM’s LAW will help guide how we design
the battery tester circuit.
OHM’s LAW states: Voltage = Current x Resistance
We write: V = I x RHere:
V = Voltage has units VoltsI = Current has units AmpsR = Resistance has units Ohms
Let’s Design the CircuitThe conceptual design
of the battery tester circuit (shown at right) will allow a very high (almost infinite) current to flow across the diode.
To prevent exceeding the current spec of the diode, we will use Ohm’s Law to limit the current.
+ DIODE -
V=IR
Let’s Design the CircuitRearranging V=IR, we see I = V/R.
We choose R to achieve a current, I = V/R at a safe level for the diode, using V = 9V, for a 9 volt battery.
Simply put, solve the equation!(The components have been selected for you
and will be provided in the lab.)
V=IR
Battery Tester Circuit
BATTERY
++
--
RESISTOR Used to limit current.
Using Ohm’s Law, we arrive at the final Battery Tester Circuit shown in the schematic!
LED: Which side is positive?
Positive Side is Round
P N
Positive Lead is LONGER
Electrical Symbol
Build Battery Tester Circuit A fundamental skill needed to assemble
electronic projects is that of soldering.
The idea is simple: Join electrical parts together to form an electrical connection
Use a molten mixture of lead and tin (solder)
together with a soldering iron.
For more information, see: http://www.epemag.wimborne.co.uk/solderfaq.htm
Build Battery Tester Circuit in LabGet components
for battery tester circuit: LEDResistorBattery Leads
Attach these components on a circuit board & solder connections between them.Photographs © 1996-2006 Alan Winstanley WORLD
COPYRIGHT RESERVED
RESOURCES:
Online Soldering Guide
Engineering Staff
Equipment in Rooms 305 & 311
Photographs © 1996-2006 Alan Winstanley WORLD COPYRIGHT RESERVED
Build Battery Tester Circuit in Lab
References Information & Photo Source – Slides 3 through 10 & 16
How Stuff Works: http://electronics.howstuffworks.com/led1.htm Wikipedia LED polarity photo: http://en.wikipedia.org/wiki/Image:%2B-
_of_LED.svg
Copyright Notice – Information on Slide 17 & Photos Slide 18 Everyday Practical Electronics Soldering Guide:
http://www.epemag.wimborne.co.uk/solderfaq.htm
Text © 1996-2006 Wimborne Publishing Limited, Wimborne, Dorset, England. Everyday Practical Electronics Magazine has provided this document as a free web resource to help constructors, trainees and students. You are welcome to download it, print it and distribute it for personal or educational use. It may not be used in any commercial publication, mirrored on any commercial site nor may it be appended to or amended, or used or distributed for any commercial reason, without the prior permission of the Publishers.
Photographs © 1996-2006 Alan Winstanley WORLD COPYRIGHT RESERVED
Presentation Created by: Alisa N. Gilmore, P.E. Department of Computer and Electronics Engineering, University of Nebraska-Lincoln, July 2006; updated July 2007 and July 2008