breaker panel sp-1000x - special projects group€¦ · sp-1000x panic device power controller 1)...

14
ON 1234 Manual Test FA LEDS IN1 IN2 Bat AC C NO Delayed1 Follower 1 C NO Supervision C NO Delayed2 Follower 2 C NO C NO 24 VDC + - 12 VDC + - GND GND GND FACP IN1 IN2 G N L Bat - Bat + - + - + Out 1 Out 2 SP-1000X Panic Device Power Controller Access Control Panel BY OTHERS Dry Output Contacts Rated 1.0A @ 28vdc min. Lock release time to be controlled by access system controller NC C NO NC C NO dps input rex input (888) 284-4774 These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand. COPYRIGHT SPECIAL PROJECTS GROUP, INC. FOR REFERENCE ONLY © 2018 This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge. Function Statement: From exterior - locked condition: From exterior - unlocked condition: From interior - locked condition: From interior - unlocked condition: General: SGL_etwbutt_RXEL1690_SP1000X.vsd Title: Drawn By: Door: 110B Project: 63-159706 OP / SO#3506101 HWSET: 9.0 / ARCH: 41.0 1/18/2018 Date: 1/18/2018 1/18/2018 Date Printed: Last Revised: 2 Pg: 1 OF Cody Richardson For: Kawneer Company 5:33:03 PM SO: 132930 Access by presenting valid credential to retract exit device latchbolts electronically. Manual entry by key override via cylinder control. Door to remain locked unless exit device latchbolts held retracted electronically by access system. Free egress at all times by means of exit device. Free egress at all times by means of exit device. 1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power. NOTES: 2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code. 4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer. 5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction. Interior Exterior Wire gage, type and number of conductors, per equipment manufacturer. Card Reader by Others Electrical breaker panel Line voltage wire type and gage, per local electrical code. Securitron M-GY Door Position Switch Electrical Circuit Legend Red = (+)VDC Power Black = (-) VDC Power Green = Signaling Blue = Activation Violet = Monitoring/Supervisory Brown = AC High Voltage EL-1690-NLOP Red +24vdc Gray LX NO Wht LX COM Vio LX NC Yel RX NC Red/Grn RX COM Blu RX NO SP1000X to be supplied BY KAWNEER McKinney T4A3786-QC8 Electric Thru-Wire Butt Hinge 14 AWG - 100ft max 12 AWG - 200ft max

Upload: others

Post on 14-Aug-2020

5 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Supe

rvis

ion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

SP-1000XPanic Device Power

Controller

Access Control PanelBY OTHERS

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

NC C NONC C NO

dps input

rex input

(888) 284-4774

© 2015

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2018

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Function Statement:From exterior - locked condition: From exterior - unlocked condition: From interior - locked condition: From interior - unlocked condition: General:

SGL_etwbutt_RXEL1690_SP1000X.vsdTitle:

Drawn By:

Door: 110BProject: 63-159706 OP / SO#3506101

HWSET: 9.0 / ARCH: 41.01/18/2018Date: 1/18/20181/18/2018Date Printed: Last Revised:

2Pg: 1 OFCody Richardson For: Kawneer Company

5:33:03 PMSO: 132930

Access by presenting valid credential to retract exit device latchbolts electronically. Manual entry by key override via cylinder control.Door to remain locked unless exit device latchbolts held retracted electronically by access system.

Free egress at all times by means of exit device. Free egress at all times by means of exit device.

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction.

Interior Exterior

Wire gage, type and number of conductors, per equipment manufacturer.

Card Reader

by Others

Electrical breaker panel

Line voltage wire type and gage, per local

electrical code.

Securitron M-GYDoor Position Switch

Electrical Circuit LegendRed = (+)VDC Power

Black = (-) VDC PowerGreen = Signaling Blue = Activation

Violet = Monitoring/SupervisoryBrown = AC High Voltage

EL-1690-NLOP

Red +24vdc

Gray LX NOWht LX COM

Vio LX NC

Yel RX NC

Red/Grn RX COM

Blu RX NO

SP1000X to be supplied

BY KAWNEER

McKinney T4A3786-QC8

Electric Thru-WireButt Hinge

14 AWG - 100ft max12 AWG - 200ft max

Page 2: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

(888) 284-4774

© 2014

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2018

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

SGL_etwbutt_RXEL1690_SP1000X.vsdTitle:

Drawn By:

Door: 110BProject: 63-159706 OP / SO#3506101

HWSET: 9.0 / ARCH: 41.01/18/2018Date: 1/18/20181/18/2018Date Printed: Last Revised:

2Pg: 2 OFCody Richardson For: Kawneer Company

5:33:03 PMSO: 132930

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction.

Interior Exterior

Electrical Breaker Panel

Yale 782Power Supply

110-120VAC 50/60Hz / 750mA

Access Control Panel

BY OTHERS

Card Reader

Box Size by supplier

Line voltage wire type, gage and

number of conductors by electrical contractor. 18 AWG / 3 Pair

Wire type, gage and number of conductors

by hardware manufacturer.2 Conductor

14 AWG up to 100ft12 AWG up to 200ft

SP-1000XPanic Device

Power Controller

13"H x 12.5"W x 3.25"D

Input 115vac / 6.3amp

BY OTHERS

18 AWG / 1 Pair

Page 3: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Supe

rvis

ion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

SP-1000XPanic Device Power

Controller

Access Control PanelBY OTHERS

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

NC C NONC C NO

dps input

rex input

(888) 284-4774

© 2015

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2018

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Function Statement:From exterior- locked condition: From exterior - unlocked condition: From interior - locked condition: From interior - unlocked condition: General:

Pair_RXEL1690_SP1000X.vsdTitle:

Drawn By:

Door: 2801CCProject: 63-159706 OP / SO#3506101

HWSET: 13.0 / ARCH: 601/18/2018Date: 1/18/20181/18/2018Date Printed: Last Revised:

2Pg: 1 OFCody Richardson For: Kawneer Company

5:21:14 PMSO: 132930

Access by presenting valid credential to retract exit device latchbolts electronically. Manual entry by key override on active leaf via cylinder control.Doors to remain locked unless exit device latchbolts held retracted electronically by access system.

Free egress at all times by means of exit device. Request to exit signal sent to access system upon egress for forced door alarm event shunting. Free egress at all times by means of exit device. Request to exit signal sent to access system upon egress for forced door alarm event shunting.

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction.

Interior Exterior

Wire gage, type and number of conductors, per equipment manufacturer.

Card Reader

by Others

Electrical breaker panel

Line voltage wire type and gage, per local

electrical code.

Securitron M-GYDoor Position Switch

Electrical Circuit LegendRed = (+)VDC Power

Black = (-) VDC PowerGreen = Signaling Blue = Activation

Violet = Monitoring/SupervisoryBrown = AC High Voltage

RX-EL-1690-NLOP RX-EL-1690-EO

Red +24vdc

Gray LX NOWht LX COM

Vio LX NC

Yel RX NC

Red/Grn RX COM

Blu RX NO

Red +24vdc

Gray LX NOWht LX COM

Vio LX NC

Yel RX NC

Red/Grn RX COM

Blu RX NO

SP1000X to be supplied

BY KAWNEER

14 AWG - 100ft max12 AWG - 200ft max

Von Duprin EPT-10Electric Power Transfer

Page 4: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

(888) 284-4774

© 2014

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2018

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Pair_RXEL1690_SP1000X.vsdTitle:

Drawn By:

Door: 2801CCProject: 63-159706 OP / SO#3506101

HWSET: 13.0 / ARCH: 601/18/2018Date: 1/18/20181/18/2018Date Printed: Last Revised:

2Pg: 2 OFCody Richardson For: Kawneer Company

5:21:14 PMSO: 132930

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction.

Interior Exterior

Electrical Breaker Panel

Yale 782Power Supply

110-120VAC 50/60Hz / 750mA

Access Control Panel

BY OTHERS

Card Reader

Box Size by supplier

Line voltage wire type, gage and

number of conductors by electrical contractor.

18 AWG / 2 Pair

18 AWG / 6 Pair

Wire type, gage and number of conductors

by hardware manufacturer.

18 AWG / 1 Pair

18 AWG / 1 Pair

2 Conductor 14 AWG up to 100ft12 AWG up to 200ft

2 Conductor 14 AWG up to 100ft12 AWG up to 200ft

SP-1000XPanic Device

Power Controller

13"H x 12.5"W x 3.25"D

Input 115vac / 6.3amp

BY OTHERS

Page 5: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Supe

rvis

ion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

SP-1000XPanic Device Power

Controller

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction.

(888) 284-4774

© 2017

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2017

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Function Statement:From exterior- locked condition: From exterior - unlocked condition: From interior - locked condition: From interior - unlocked condition: General:

Pair_RX-EL-1690_SP1000X.vsdTitle:

Drawn By:

Door: 628BProject: PO#62-159033op_SO#3497740

HWSET: 1.0/ARCH: 1812/11/2017Date: 12/11/2017Date Printed: Last Revised:

2Pg: 1 OFCody Richardson For: Kawneer Company

5:24:15 PMSO: 132477

Access by presenting valid credential to retract electric exit device latchbolts. Manual entry by key on active leaf.Doors to remain locked unless active electric exit device latchbolts held retracted by access system.

Free egress at all times by means of exit device. RX signal sent to access system upon egress via exit device push pad for forced door alarm event (DPS) shunting.Free egress at all times by means of exit device. RX signal sent to access system upon egress via exit device push pad for forced door alarm event (DPS) shunting.

Electrical breaker panel

Access Control PanelBY OTHERS

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

NC C NONC C NO

Card Reader by

Others

Line voltage wire type and gage, per

local electrical code.

Wire gage, type and number of conductors, per equipment manufacturer.

Von Duprin EPT-10Electric Power Transfer

14 AWG - 100ft max12 AWG - 200ft max

dps input

Door Position SwitchBY OTHERS

Interior ExteriorElectrical Circuit Legend

Red = (+)VDC PowerBlack = (-) VDC Power

Green = Signaling Blue = Activation

Violet = Monitoring/SupervisoryBrown = AC High Voltage

rx input

RX-EL-1692NL-OP RX-EL-1690EO

Page 6: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.5) It is considered good electrical practice to run spare wires at any location that may be difficult to access after construction.

(888) 284-4774

© 2014

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2017

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Pair_RX-EL-1690_SP1000X.vsdTitle:

Drawn By:

Door: 628BProject: PO#62-159033op_SO#3497740

HWSET: 1.0/ARCH: 18

12/11/2017Date: 12/11/2017Date Printed: Last Revised:

2Pg: 2 OFCody Richardson For: Kawneer Company

5:24:15 PMSO: 132477

Electrical Breaker Panel Access Control

PanelBY OTHERS

Card Reader

Box Size by supplier

Line voltage wire type, gage and

number of conductors by electrical contractor.

Wire type, gage and number of conductors

by hardware manufacturer.

2 Conductor 14 AWG up to 100ft12 AWG up to 200ft

2 Conductor 14 AWG up to 100ft12 AWG up to 200ft

18 AWG / 6 Pair

Interior Exterior

18 AWG / 2 Pair

SP-1000XPanic Device

Power Controller

13"H x 12.5"W x 3.25"D

Input 115vac / 6.3amp

18 AWG / 1 Pair 18 AWG / 1 Pair

Page 7: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1 CN

OSu

perv

isio

nC

NO

Del

ayed

2Fo

llow

er 2 C

NO

CN

O24

VD

C

+-

12 V

DC

+-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL B

at -

Bat

+

- + - +

Out 1 Out 2

SP-1000XPanic Device Power

Controller

(888) 284-4774

© 2014

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Function Statement:From exterior- locked condition: From exterior - unlocked condition: From interior - locked condition: From interior - unlocked condition: General:

First Choice EL Device 2 Pair Active SP-1000X AOBO.vsdTitle:

Drawn By:

Door: Example A/BProject: Sample Diagram

HWSET: 1A9/14/2017Date: 9/14/2017Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: First Choice Building Products

11:58:41 AMSO:

Access by presenting valid credential at reader interface to retract active leaf electric exit device latch and enable exterior actuator use. Doors to remain locked unless electric exit device latch held retracted by access system or momentarily unlocked by push button.

Free egress at all times by means of exit device or by pressing interior handicap actuator to unlock and swing door. Free egress at all times by means of exit device or by pressing interior handicap actuator to unlock and swing door.

This is a basic/generic sample diagram for reference only. For project specific wiring diagrams, please contact Special Projects Group.

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

Card Reader

by Others

+-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

+-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

Exit

Optional momentary switch. Unlock with

depression.

Exit

Optional momentary switch. Unlock with

depression.

Access Control Panel

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

NC C NONC C NO

Electrical breaker panel

Line voltage wire type and gage, per local electrical code.

Card Reader

by Others

Wire gage, type and number of conductors, per equipment manufacturer.

Wire gage, type and number of conductors, per equipment manufacturer.

Interior ExteriorExterior

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE: Make certain to maintain consistent wire color across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

Out 2

14 AWG – 40ft max12 AWG – 60ft max10 AWG – 100ft max

With EPT

Auto Operator

Push to Open

C NO

Push to Open

C NO

ActivationLock Relay

First Choice EL-3000

+-First Choice 3000 First Choice EL-3000

+-First Choice 3000

Page 8: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

Access Control PanelBY OTHERS

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

NC C NONC C NO

(888) 284-4774

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

Function Statement:From exterior- locked condition: Access by presenting valid card to unlock active leaf and make exterior actuator available to swing active leaf.From exterior - unlocked condition: Doors to remain locked unless active leaf held unlocked by access system. Press actuator to swing active leaf.From interior - locked condition: Free egress by means of exit device. Interior actuator always available to swing door.From interior - unlocked condition: Free egress by means of exit device. Interior actuator always available to swing door.General: This is a basic generic wiring diagram. For a project specific wiring diagram contact your Kawneer representative.

FOR REFERENCE ONLY

Paneline EL 1 Active w Operator SP-1000X.vsdTitle:

Drawn By:

Door: Kawneer PanelineProject: Paneline EL 1 Active w Operator

Heading: Paneline EL

3/19/2014Date: 2/19/20142/19/2014Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: Kawneer Company, Inc.

4:09:35 PM

© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Card Reader by

Others

Electrical breaker panel

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

PUSH

+-PUSH

Auto Operator

Push to Open

C NO

Push to Open

C NO

Activation

Lock Relay

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

Handicap Actuator

Wire gage, type and number of conductors, per equipment manufacturer.

14 AWG – 40ft max12 AWG – 60ft max10 AWG – 100ft max

With EPT

Line voltage wire type and gage, per local electrical code.

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

Interior Exterior

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Sup

ervi

sion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

Page 9: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Sup

ervi

sion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

(888) 284-4774

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

Function Statement:From exterior- locked condition: Access by presenting valid credential to unlock door.From exterior - unlocked condition: Doors to remain locked unless held unlocked by access control system.From interior - locked condition: Free egress at all times by means of exit device.From interior - unlocked condition: Free egress at all times by means of exit device.General: This is a basic generic wiring diagram. For a project specific wiring diagram contact your Kawneer representative.

FOR REFERENCE ONLY

Paneline EL Exit Device 1 Single SP-1000X.vsdTitle:

Drawn By:

Door: Kawneer Paneline

Project: Paneline EL 1 single door

Heading: Paneline EL

5/5/2014Date: 01/22/20145/5/2014Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: Kawneer Company, Inc.

5:14:26 PM

© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Exit

NO

C

NC

NC C NO

Access Control Panel

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

Card Reader by

Others

Electrical breaker panel

Line voltage wire type and gage, per local electrical code.

14 AWG – 40ft max12 AWG – 60ft max10 AWG – 100ft max

With EPT

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

Optional momentary switch. Unlock with depression.

PUSH

+-

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

Wire gage, type and number of conductors, per equipment manufacturer.

Electric Power Transfer

Page 10: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Supe

rvis

ion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

(888) 284-4774

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

Function Statement:From exterior- locked condition: Access by presenting valid credential to unlock active leaf.From exterior - unlocked condition: Doors to remain locked unless held unlocked by access control system.From interior - locked condition: Free egress at all times by means of exit device.From interior - unlocked condition: Free egress at all times by means of exit device.General: This is a basic generic wiring diagram. For a project specific wiring diagram contact your Kawneer representative.

FOR REFERENCE ONLY

Paneline EL Exit Device 1 Pair 1 Active SP1000X.vsdTitle:

Drawn By:

Door: Kawneer PanelineProject: Paneline EL 1 Pair with 1 Active

Heading: Paneline EL

5/5/2014Date: 5/5/201401/20/2014Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: Kawneer Company, Inc.

5:17:29 PM

© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

NC C NO

Access Control Panel

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

Card Reader by

Others

Electrical breaker panel

Line voltage wire type and gage, per local

electrical code.

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

PUSH

+-PUSH

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

Wire gage, type and number of conductors, per equipment manufacturer.

Exterior

14 AWG - 40ft max12 AWG - 60ft max

10 AWG - 100ft max

Exit

NO

C

NC

Optional momentary switch. Unlock with depression.

Interior

Page 11: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Sup

ervi

sion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

(888) 284-4774

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

Function Statement:From exterior- locked condition: Access by presenting valid credential to unlock doors.From exterior - unlocked condition: Doors to remain locked unless held unlocked by access control system.From interior - locked condition: Free egress at all times by means of exit device.From interior - unlocked condition: Free egress at all times by means of exit device.General: This is a basic generic wiring diagram. For a project specific wiring diagram contact your Kawneer representative.

FOR REFERENCE ONLY

Paneline EL Exit Device 1 Pair 2 Active SP1000X.vsdTitle:

Drawn By:

Door: Kawneer Paneline

Project: Paneline EL 1 Pair with 2 Active

Heading: Paneline EL

5/5/2014Date: 01/20/201401/20/2014Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: Kanweer Company Inc.

5:18:41 PM

© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Exit

NO

C

NC

NC C NO

Access Control Panel

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

Card Reader by

Others

Electrical breaker panel

Line voltage wire type and

gage, per local electrical code.

14 AWG – 40ft max12 AWG – 60ft max10 AWG – 100ft max

With EPT

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREYOptional momentary switch.

Unlock with depression.

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

PUSH

+-PUSH

+ -

Set Dip Switch 1- ONFor Sequential Mode

Wire gage, type and number of conductors, per equipment manufacturer.

Interior Exterior

Page 12: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat

AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Sup

ervi

sion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Bat

-

Bat

+

- + - +

Out 1 Out 2

(888) 284-4774

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

Function Statement:From exterior- locked condition: Access by presenting valid credential to unlock door.From exterior - unlocked condition: Doors to remain locked unless held unlocked by access control system.From interior - locked condition: Free egress at all times by means of exit device.From interior - unlocked condition: Free egress at all times by means of exit device.General: This is a basic generic wiring diagram. For a project specific wiring diagram contact your Kawneer representative.

FOR REFERENCE ONLY

Paneline EL Exit Device 1 Single SP-1000X.vsdTitle:

Drawn By:

Door: Kawneer Paneline

Project: Paneline EL 1 single door

Heading: Paneline EL

5/5/2014Date: 01/22/20145/5/2014Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: Kawneer Company, Inc.

5:14:26 PM

© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Exit

NO

C

NC

NC C NO

Access Control Panel

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

Card Reader by

Others

Electrical breaker panel

Line voltage wire type and gage, per local electrical code.

14 AWG – 40ft max12 AWG – 60ft max10 AWG – 100ft max

With EPT

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

Optional momentary switch. Unlock with depression.

PUSH

+-

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

Wire gage, type and number of conductors, per equipment manufacturer.

Electric Power Transfer

Page 13: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat AC

CN

OD

elay

ed 1

Follo

wer

1 CN

OSu

perv

isio

nC

NO

Del

ayed

2Fo

llow

er 2 C

NO

CN

O24

VD

C

+-

12 V

DC

+-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL B

at -

Bat

+

- + - +

Out 1 Out 2

(888) 284-4774

© 2014

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

FOR REFERENCE ONLY© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

Function Statement:From exterior- locked condition:From exterior - unlocked condition:From interior - locked condition: From interior - unlocked condition:General:

Paneline EL Exit Device 2 Pair 1 Active SP-1000X.vsdTitle:

Drawn By:

Door: Project:

Heading:

3/19/2014Date: 3/19/20143/19/2014Date Printed: Last Revised:

1Pg: 1 OFCody Richardson For: Kawneer Company, Inc.

10:44:32 AMSO: SPG SO

Access by presenting card to unlock active leaf.Doors to remain locked unless held unlocked by access system or momentarily unlocked by push button.Free egress at all times by means of exit device.Free egress at all times by means of exit device.This is a absic and generic diagram. For a project specific wiring diagram, please contact your Kawneer representative.

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

Card Reader

by OthersPUSH

+-PUSH

+-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

PUSH

+-PUSH

+-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

Exit

NOC

NC

Optional momentary switch. Unlock with

depression.

Exit

NOC

NC

Optional momentary switch. Unlock with

depression.

Access Control Panel

Dry Output ContactsRated 1.0A @ 28vdc min.

Lock release time to be controlled by access system controller

NC C NONC C NO

Electrical breaker panel

Line voltage wire type and gage, per local electrical code.

Card Reader

by Others

Wire gage, type and number of conductors, per equipment manufacturer.

Wire gage, type and number of conductors, per equipment manufacturer.

With EPT or Door Loop14 AWG - 40ft max12 AWG - 60ft max

10 AWG - 100ft max

Dip 1 = OFFFor Independent Mode

Interior ExteriorExterior

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

Out 2

Page 14: breaker panel SP-1000X - Special Projects Group€¦ · SP-1000X Panic Device Power Controller 1) Verify that each component requiring or supplying power has been configured for proper

ON

1 2 3 4

Man

ual T

est

FA

LED

SIN

1IN

2

Bat AC

CN

OD

elay

ed 1

Follo

wer

1C

NO

Supe

rvis

ion

CN

OD

elay

ed 2

Follo

wer

2C

NO

CN

O24

VD

C+

-12

VD

C+

-

GN

D

GN

D

GN

D

FAC

P

IN1

IN2G NL Ba

t -

Bat

+

- + - +

Out 1 Out 2

(888) 284-4774

These drawings are the sole and exclusive property of Special Projects Group and contain sensitive privileged or confidential information which may be used only for its benefit. The disclosure of these drawings to unauthorized persons is strictly prohibited. This document and all copies must be returned upon demand.

COPYRIGHT SPECIAL PROJECTS GROUP, INC.

Function Statement:From exterior- locked condition:From exterior - unlocked condition:From interior - locked condition: From interior - unlocked condition:General :

FOR REFERENCE ONLY

Paneline EL Exit with Rosslare SP-1000X.vsdTitle:

Drawn By:

Door: Kawneer PanelineProject: Paneline EL with Rosslare Key Pad

Heading: Paneline EL

3/19/2014Date: 3/19/20143/19/2014Date Printed: Last Revised:

1Pg: 1 OFCMR For: Kawneer Company, Inc.

10:47:02 AM

© 2014

This drawing is not a substitute for qualified field technicians. One hour of telephone support is available without charge.

SO: N/A

Access by means of presenting valid credential or entering valid code.Door to remain locked unless toggled unlocked by valid toggle code.

Free egress at all times by means of exit device.Free egress at all times by means of exit device.

Diagram for use with “stand alone” Rosslare AC-G43 key pad or AC-G44 key pad / proximity card reader.

321

64

57 89 0

* #

RBk

GnWh

Pr GrBnBl

YlOr

Exit

NO

C

NC

Optional remote release

button

Rosslare AC-G43or

Rosslare AC-G44

+

-

This device is polarity sensitive. Please observe polarity when connecting the provided wiring harness.

Electrical breaker panel

COMNO

1) Verify that each component requiring or supplying power has been configured for proper system voltage before applying power.

NOTES:

2) All wires to be 18 awg 100' max unless otherwise noted on drawing. Refer to manufacturers instructions for proper wire gauge on any power supply, electric device or electrified lock hardware. Manufacturers requirements take precedence. 3) All line voltage power to be I/A/W local electrical code.

4) All low voltage wires to be stranded copper unless superseded by local electrical code or electric device manufacturer.

NOTE:

Optional power transfers are available. Please note variations in wire size and maximum run length for these options.

14 AWG - 35 ft max12 AWG - 55 ft max10 AWG - 95 ft max

POWER TRANSFERS

NOTE:Make certain to maintain consistent wirecolor across the transfer to maintain polarity.

RED REDPURPLE PURPLEYELLOW YELLOW

GREY GREY

Electric Power Transfer

PUSH

+-

Out 2

14 AWG - 40ft max12 AWG - 60ft max

10 AWG - 100ft max

Line voltage wire type and gage, per

local electrical code.

Interior Exterior