Thank you for purchasing this Crest TV Wall Mount.

Crest prides itself on supplying quality audio visual accessories to consumers and businesses throughout Australia. If you follow this guide carefully, we are confident this product will help maximise the enjoyment you obtain from your audio visual equipment for many years. Please keep this guide for future reference.

TECHNICAL SUPPORTIf you have any questions regarding the warranty, installation or use of this product, please contact our Technical Support Centre on 1800 812 261.

WARRANTY

This Crest TV Wall Mount carries a limited warranty of five (5) years from the date of purchase.

Crest, by this warranty, will at its discretion repair or replace the product or its components if found to be defective in workmanship or materials. Where a warranty claim is made, Crest may require the customer at their expense to return theproduct and or its components to Crest or a Crest representative for inspection.

This limited warranty covers supply of the replacement product (which may vary from the one originally purchased) only and does not extend to, nor covers costs associated with, demounting, removal, disposal or return of the original product, or installation of the replacement product.

This limited warranty does not cover damage or loss resulting from intentional or un-intentional misuse, tampering with, neglect or incorrect installation or use of this product or where the product has been used for purposes other than that for which it is designed or for supporting displays beyond the product’s capability as stated on the product’s original packaging and in this guide. Failure to strictly comply with this installation guide may result in forfeiture of the warranty by the purchaser, user or owner.

Any warranty claim must be accompanied by proof of purchase showing date and location of purchase.

INSTALLATION INSTRUCTIONS

IMPORTANT

1. Installation of this TV mount will be easier if two people are involved.2. Some images in this guide may vary slightly from the actual components supplied.3. Ensure this Installation Guide is completely read and understood before attempting installation.4. Mount MUST NOT be installed solely in plasterboard, fibre cement and similar surfaces.5. Mount MUST be installed in sound supporting structures such as those made of timber, steel or masonry using appropriate fasteners.6. The supporting structure must be capable of sustaining the combined weight of the TV mount and the display otherwise the structure must be reinforced.7. The fasteners supplied in this hardware pack allow for fixing into timber and masonry only. If installing into a supporting structure made of steel, appropriate fasteners must be used and sourced from an appropriate supplier.8. Use appropriate tools and safety equipment and ensure adequate ventilation during installation.9. If uncertain about any aspect of installation, contact Crest or an installation professional.

TOOLS REQUIREDDrywall (Timber Frame) Installation

• Stud finder• Spirit level• Pencil• Drill

• Long neck phillips head screwdriver• 5mm diameter high speed drill bit• Adjustable spanner

In addition, for Masonry Installation

• Drill with hammer function• 8mm masonry drill bit• Hammer

BFP7FM This model will suit most flat panel TV sizes from 17 to 32 inches (43 to 81cm) as long as they weigh 30kg maximum and possesses a mounting hole pattern of 75, 100, 200 square or 100 x 200mm (h x w)

Warranty and Installation GuideFull Motion Flat Panel Wall Mount

BFP7FM

Warranty and Installation GuideFull Motion Flat Panel Wall Mount

BFP7FM

STEP 1 – ATTACH WALL MOUNT COMPONENTS TO WALL

STEP 2 – ATTACH MOUNTING PLATE TO TV

A. Installing in Drywall (Timber frame). See Figures 1.1 & 1.2.

1. Locate centre of timber stud using a stud finder 2. Mark three fixing holes over stud centers using the wall plate as a guide. Ensure wall plate is straight and level.3. Predrill holes to a depth of 30mm using high speed 3mm drill bit. If installing in hardwood, larger diameter and deeper holes may be required.4. Attach the wall plate (firstly insert wire saddle M-J into the provided holes under the bottom arm closest to the wall as shown in figure 1 so as to use for cable management and know which way is the correct way up for the bracket) using long screws (W-A) ST5.5x50mm Woodscrew and (W-C) D6 Washers. Do not over tighten.

1. Check the back of your TV to find the appropriate mounting pattern.2. Sort through provide bolts M-A to M-D until you find the correct size that easily fits into the back of your TV and fits snugly (the bolt must turn at least 3 full turns). Once you have selected the bold then find the corresponding washer. If no bolts fit you will need to go to your local hardware to find the correct sized bolt and washer.3. Now using the correct mounting bolt size and length through corresponding round washers to attach mounting plate to rear of TV (see figure 2.1). If one of the smaller bolts are selected (M-A or M-B) then use the small hole spacer M-I as shown in figure 2.2 to fill out the wall plate hole and reduce its size for a snugger fit. To avoid damaging TV, do not over tighten bolts. (Crest is not responsible for any damage caused by screwing the bolt too far into the back of the TV)

B. Installing in Masonry. See Figures 2.1 & 2.2.

1. Mark three fixing holes using wall plate as guide(see figure 1.2). Ensure plate is straight and level.2. Predrill holes to a depth of 60mm using 8mm masonry drill bit. Clean out holes.3. Fully insert masonry anchors (W-B). Tap in with hammer if required. 4. Attach the wall plate (firstly insert wire saddle M-J into the provided holes under the bottom arm closest to the wall as shown in figure 1 so as to use for cable management and know which way is the correct way up for the bracket)using long screws (W-A) ST5.5x50mm Screw and (W-C) D6 Washers (see figure 1.3). Do not over tighten.

Figure 1.1

Figure 3.1 Figure 3.2Figure 1.2

Figure 2.1

Figure 2.2

M-A

M-B

M-C

M-D

M-E

M-F

M-G

M4 x 10mm

M5 x 10mm

M6 x 10mm

M8 x 15mm

D4 Washer

D5 Washer

D6 Washer

4

4

4

4

4

4

4

Item Description Qty

M-H

M-I

M-J

M-K

W-A

W-B

W-C

D8 Washer

Custom

Wire Saddle

Allen Key

ST5.5 Lag Bolt

Concrete Anchor

D6 Washer

4

4

2

2

3

3

3

Item Description Qty

HARDWARE KIT CONTENTS

Warranty and Installation GuideFull Motion Flat Panel Wall Mount

ww

w

.crest.com.aute

ch

nical support

1800 812 261

165 South Pine RdPO Box 5658

Brendale Qld 4500

STEP 3 – PITCH ANGLE ADJUSTMENT AND MAINTENANCE

1. Use the tilt adjusting knob behind the back of the wall plate to adjust your TV to the desired viewing angle, the pitch can be adjusted between +20 degrees and -20 degrees as shown in figure 3.1.2. Once your TV is connected you can now use the Wire Saddles (M-J figure 1) to manage your cables.3. If your bracket is too loose and moves around too easy or vice versa too tight please use provided Allen Keys M-K to tighten or loosen as required. Warning- do not loosen to much so that the bracket falls apart.

Figure 4.1

69mm

70mm

162mm

130m

m

205m

m

32mm

220mm

220m

m

+20º

-20º