ba_cp-1613-a2_76

7/27/2019 BA_CP-1613-A2_76

1/24

P 1613 A2 ___________________ Preface

___________________Description of the device

___________________Software installationSIMATIC NET ___________________Hardware installation

PG/PC - Industrial Ethernet ___________________CP 1613 A2 Configuration___________________Technical specifications

Operating Instructions___________________Approvals

12/2012C79000-G8976-C303-01

7/27/2019 BA_CP-1613-A2_76

2/24

Siemens AGIndustry SectorPostfach 48 4890026 NRNBERGGERMANY

Order number: C79000-G8976-C303 12/2012 Technical data subject to change

Copyright Siemens AG 2012.All rights reserved

Legal informationWarning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to preventdamage to property. The notices referring to your personal safety are highlighted in the manual by a safety alertsymbol, notices referring only to property damage have no safety alert symbol. These notices shown below aregraded according to the degree of danger.

DANGERindicates that death or severe personal injury willresult if proper precautions are not taken.

WARNINGindicates that death or severe personal injury mayresult if proper precautions are not taken.

CAUTIONindicates that minor personal injury can result if proper precautions are not taken.

NOTICEindicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger willbe used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating toproperty damage.

Qualified PersonnelThe product/system described in this documentation may be operated only by personnel qualifiedfor the specifictask in accordance with the relevant documentation, in particular its warning notices and safety instructions.Qualified personnel are those who, based on their training and experience, are capable of identifying risks andavoiding potential hazards when working with these products/systems.

Proper use of Siemens productsNote the following:

WARNINGSiemens products may only be used for the applications described in the catalog and in the relevant technicaldocumentation. If products and components from other manufacturers are used, these must be recommendedor approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation andmaintenance are required to ensure that the products operate safely and without any problems. The permissibleambient conditions must be complied with. The information in the relevant documentation must be observed.

TrademarksAll names identified by are registered trademarks of Siemens AG. The remaining trademarks in this publicationmay be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of LiabilityWe have reviewed the contents of this publication to ensure consistency with the hardware and softwaredescribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, theinformation in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

7/27/2019 BA_CP-1613-A2_76

3/24

Table of contents

1 Preface ...................................................................................................................................................... 52 Description of the device ........................................................................................................................... 93 Software installation................................................................................................................................. 11

3.1 Installing the driver.......................................................................................................................11

3.2 Uninstalling the driver ..................................................................................................................11

3.3 Installing the SIMATIC NET PC software ....................................................................................12

3.4 Uninstalling the SIMATIC NET PC software................................................................................133.5 Alternative software packets........................................................................................................13

4 Hardware installation ............................................................................................................................... 155 Configuration ........................................................................................................................................... 176 Technical specifications........................................................................................................................... 19A Approvals................................................................................................................................................. 21

Index........................................................................................................................................................ 23

CP 1613 A2

Operating Instructions, 12/2012, C79000-G8976-C303-01 3

7/27/2019 BA_CP-1613-A2_76

4/24

Table of contents

CP 1613 A2

4 Operating Instructions, 12/2012, C79000-G8976-C303-01

7/27/2019 BA_CP-1613-A2_76

5/24

Preface 1

What the consignment containsThe following components are supplied with the CP 1613 A2:

CP 1613 A2 communications processor SIMATIC NET driver CDPlease check that the consignment you have received is complete. If the consignment isincomplete, contact your supplier or your local Siemens office.

Validity of this documentationThese operating instructions are valid for the following product:

CP 1613 A2order number: 6GK1161-3AA01

NoteCP 1613This document is also valid for the CP 1613 communications processor. You will find thetechnical specifications of the CP 1613 that differ from those of the CP 1613 A2 on theProduct Support pages under the following entry ID: 23554752(http://support.automation.siemens.com/WW/view/en/23554752)

Content of this documentationThese operating instructions contain information about the installation and configuration ofthe CP 1613 A2 communications processor.

Updated operating instructions on the InternetYou will find the current version of these operating instructions on the Product Support pagesunder the following entry ID:62611661 (http://support.automation.siemens.com/WW/view/en/62611661)

Further documentationThe documents listed below contain more detailed information on commissioning and usingthe communications processor. You will find this documentation on the Product Supportpages on the Internet under the following entry link:Support (http://support.automation.siemens.com/WW/view/en)

CP 1613 A2

http://support.automation.siemens.com/WW/view/en/23554752http://support.automation.siemens.com/WW/view/en/62611661http://support.automation.siemens.com/WW/view/enhttp://support.automation.siemens.com/WW/view/enhttp://support.automation.siemens.com/WW/view/en/62611661http://support.automation.siemens.com/WW/view/en/23554752

7/27/2019 BA_CP-1613-A2_76

6/24

Preface

CP 1613 A2


Enter the entry ID shown below of the relevant manual as the search item.

Configuration manual Commissioning PC StationsThis provides you with detailed information on commissioning and configuring SIMATICNET PC communications modules.

Entry ID:13542666 (http://support.automation.siemens.com/WW/view/en/13542666)

System manual SIMATIC NET Industrial Communication with PG/PC Volume 1 Basics


Volume 2 InterfacesEntry ID:42783660 (http://support.automation.siemens.com/WW/view/en/42783660)

The system manuals introduce the topic of industrial communication and explain thecommunications protocols used. There is also a description of the OPC interface asuser programming interface.

Installation manual SIMATIC NET PC SoftwareThis document contains detailed information on installing the SIMATIC NET

PC software.


System manual Industrial Ethernet Network ManualIn this document you will find detailed information about setting up an Industrial Ethernetnetwork.


SIMATIC NET documentationYou will find the entire SIMATIC NET documentation on the pages of Product Support:10805878 (http://support.automation.siemens.com/WW/view/en/10805878)

Go to the required product group and make the following settings:

Entry list Entry type "Manuals / Operating Instructions"

Service SupportIn addition to the product documentation, the comprehensive online information platform ofSiemens Automation Customer Support supports at any time and at any location in theworld. You will find the Service & Support pages on the Internet at the following address:

(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=en)
http://support.automation.siemens.com/WW/view/en/13542666http://support.automation.siemens.com/WW/view/en/42783968http://support.automation.siemens.com/WW/view/en/42783968http://support.automation.siemens.com/WW/view/en/42783660http://support.automation.siemens.com/WW/view/en/61630923http://support.automation.siemens.com/WW/view/en/27069465http://support.automation.siemens.com/WW/view/en/10805878http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=enhttp://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=enhttp://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=enhttp://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=enhttp://support.automation.siemens.com/WW/view/en/10805878http://support.automation.siemens.com/WW/view/en/27069465http://support.automation.siemens.com/WW/view/en/61630923http://support.automation.siemens.com/WW/view/en/42783660http://support.automation.siemens.com/WW/view/en/42783968http://support.automation.siemens.com/WW/view/en/13542666

7/27/2019 BA_CP-1613-A2_76

7/24

Preface

CP 1613 A2


Apart from news, you will also find the following information there:

Product information, Product Support, Applications & Tools Technical Forum Technical Support - Ask the Siemens experts Our service offer:

Technical Consulting, Engineering support Field Service Spare parts and repairs Maintenance, optimization, modernization and more

You will find contact data on the Internet at the following address:(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)

See also(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=38718979&caller=view)

SITRAIN - Siemens training for automation and industrial solutionsWith over 300 different courses, SITRAIN covers the entire Siemens product and systemspectrum in the field of automation and drive technology. Apart from the classic range of

courses, we also offer training tailored for individual needs and a combination of differentteaching media and sequences, for example self-learning programs on CD-ROM or on theInternet.

You will find detailed information on the training curriculum and how to contact our customerconsultants at the following Internet address:

(www.siemens.com/sitrain)

SIMATIC NET glossaryExplanations of the specialist terms used in this documentation can be found in the SIMATICNET glossary.

You will find the SIMATIC NET glossary here:

SIMATIC NET Manual CollectionThe DVD ships with certain SIMATIC NET products.

On the Internet under the following entry ID:50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
http://www.automation.siemens.com/partner/guiwelcome.asp?lang=enhttps://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=38718979&caller=viewhttps://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=38718979&caller=viewhttp://www.siemens.com/sitrainhttp://support.automation.siemens.com/WW/view/en/50305045http://support.automation.siemens.com/WW/view/en/50305045http://support.automation.siemens.com/WW/view/en/50305045http://www.siemens.com/sitrainhttps://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=38718979&caller=viewhttps://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=38718979&caller=viewhttp://www.automation.siemens.com/partner/guiwelcome.asp?lang=en

7/27/2019 BA_CP-1613-A2_76

8/24

7/27/2019 BA_CP-1613-A2_76

9/24

Description of the device 2

Product featuresThe CP 1613 is a PCI module for connecting PGs/PCs to Industrial Ethernet. The essentialproperties are as follows:

RJ-45 jack for Industrial Ethernet for connecting a twisted-pair cable 15-pin D-sub socket for AUI and ITP

The 15-pin D-sub socket with slide locking mechanism is intended for connection of both

AUI transceiver cables (AUI - Attachment Unit Interface) and for connection of ITP cables(ITP - Industrial Twisted Pair).

Data rates 10/100 Mbps (half/full duplex) are supported Own processor on the CP 1613 relieves the PC/PG CPU Autosensing, autonegotiation The changeover between the AUI and ITP connector is made automatically by the

module if you use Siemens ITP cables.

ISO and TCP/IP transport protocol onboard

Hardware requirementsThe CP 1613 requires a PCI slot.

LED displayTo indicate module activity, the CP 1613 has two LEDs on its front panel that are lit whendata is being received (green) and when data is being sent (yellow).

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

10/24

Description of the device

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

11/24

3oftware installation3.1 Installing the driverInstallation

After the computer has booted, the Windows plug-and-play mechanism searches for a driverfor the communications processor. The driver is available on the "SIMATIC NET, PCSoftware" CD and on the supplied driver CD.

Selecting the suitable driverWhich driver you need to install depends on the communications processor and theconditions in which it is used:

OfficeIf the communications processor is used only in an office environment in a PC network(without SIMATIC NET PC software), install the driver from the supplied driver CD.

IndustryIf the communications processor is operated in an industrial network along with aSIMATIC NET communications processor software product, install the supplied "SIMATICNET, PC Software, Edition 2005" (V 6.3) CD or higher.

3.2 Uninstalling the driverUninstalling after using the communications processor with SIMATIC NET PC software

The "SIMATIC NET PC Software" DVD is installed on the PC.

Uninstall the SIMATIC NET PC software as described in the Installation Instructions of the"SIMATIC NET, PC Software" DVD.

NOTICEUninstallingThe procedure recommended here uninstalls the entire SIMATIC NET PC software on thePC not only the driver for the communications processor.

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

12/24

Software installation

3.3 Installing the SIMATIC NET PC software

CP 1613 A2


Uninstalling after using the communications processor without SIMATIC NET PC softwareIf you remove the communications processor from your PC and want to uninstall the driver,

follow the steps below:1. Open the Control Panel and go to the "Hardware" tab.2. Click on the "Device Manager" button in the "Device Manager" group.3. Right-click on the driver of the communications processor you are using, for example

"SIMATIC Miniport CP1613 PCI Adapter", in the path of the "SIMATIC NET" symbol andselect the "Uninstall" menu command and confirm removal with "OK".

4. Restart your PC to remove the driver completely.

3.3 Installing the SIMATIC NET PC softwareSIMATIC NET PC software

The SIMATIC NET PC software is one of several software packages with which you canoperate the CP in your PG/PC. You will find information on alternatives in the section"Alternative software packets(Page 13)".

To configure the CP, you require additional configuration software. You will find informationon the configuration software in the section "Configuration(Page 17)".

ConditionThe plug and play function is activated in the BIOS of your PG/PC.

Prior to hardware installationInstall the software as described in the installation manual "SIMATIC NET PC Software".You will find this installation manual on the Product Support pages under the following entryID:61630923 (http://support.automation.siemens.com/WW/view/en/61630923)

You should also note the current information on the SIMATIC NET PC software on theProduct Support pages in:

(http://support.automation.siemens.com/WW/view/en/43409428/133400)

After the hardware installationAfter installing the CP, your PG/PC automatically searches for a suitable driver.

1. Follow the instructions of the Hardware Wizard of Windows.2. Do not activate the search for drivers on the Internet.
http://support.automation.siemens.com/WW/view/en/61630923http://support.automation.siemens.com/WW/view/en/43409428/133400http://support.automation.siemens.com/WW/view/en/43409428/133400http://support.automation.siemens.com/WW/view/en/61630923

7/27/2019 BA_CP-1613-A2_76

13/24


3.4 Uninstalling the SIMATIC NET PC software

CP 1613 A2


3.4 Uninstalling the SIMATIC NET PC softwareCondition

The SIMATIC NET PC software is installed on the PG/PC.

ProcedureNoteThe procedure recommended here deletes the entire SIMATIC NET PC software on thePG/PC not only the driver for the communications processor.

Uninstall the entire software package as described and recommended in the installationmanual "SIMATIC NET PC Software".

You will find the installation manual on the SIMATIC NET DVD or on the Product Supportpages under the following entry ID:

61630923 (http://support.automation.siemens.com/WW/view/en/61630923)

3.5 Alternative software packetsAlternatives to SIMATIC NET PC software

To operate the CP, alternative software packages such as STEP 7 V5.5 or STEP 7Professional V11 are also available. You will find current information on this on the ProductSupport pages under the following entry ID:

http://support.automation.siemens.com/WW/view/en/61630923http://support.automation.siemens.com/WW/view/en/47071380http://support.automation.siemens.com/WW/view/en/47071380http://support.automation.siemens.com/WW/view/en/61630923

7/27/2019 BA_CP-1613-A2_76

14/24


3.5 Alternative software packets

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

15/24

4ardware installationNumber of permitted communications processors

NoteA maximum of four CP 1613 modules can be installed in one PG/PC at the same time.

ProcedureTo install and connect up the communications processor follow the steps outlined below:

NoteWhen handling the module, make sure that you do not touch the connectors or the electroniccomponents.

1. Turn off your computer and pull out the power cable connector from the socket.2. Open the housing of the computer as described in the manual for your PG/PC and

remove the cover of a free PCI slot in your computer.

3. Remove the communications processor from its packaging.4. Insert the communications processor in the PCI slot.

Make sure that the communications processor is inserted and secured correctly.

5. Close the computer housing as described in the manual accompanying your PG/PC6. Insert the connecting cable (TP, AUI or ITP) in the socket on the front panel of the

communications processor.

7. Plug the power supply connector into the socket again and turn on your computer.

Notes on the AUI and TP socketsNoteUse only one or the other socket. Both sockets must not be operated at the same time.

NoteIf you change from one socket to the other during ongoing operation, it is possible that thechangeover will not be detected. We recommend that you only change from one socket tothe other when the device is turned off.

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

16/24

Hardware installation

CP 1613 A2


Transceiver power supply

NoteThe CP 1613 provides a voltage of 12 V to supply a transceiver on its AUI interface. Themaximum load for this is a permanent current of 500 mA!

AUI cableNoteThe CP 1613 has 2 sockets for connecting network cables. If you use the AUI interface forthe AUI transceiver cable, breaks of 2 to 3 seconds can occur sporadically in

communication. To avoid problems due to this, do not set timeouts for this mode to less than5 seconds!

NoteThis section applies only to users of he SIMATIC NET-CD. In the "Configuration Console"program, the current network parameters of the CP 1613 module among other things aredisplayed in the "Network Parameters" tab. As long as no valid link to the partner is detected,"unknown" is displayed here. Since there is no link detection with AUI, the reception offrames is used as a substitute for link detection. If no frames are received and the AUI cableis plugged in, it is assumed that no link exists. A valid link is assumed only when the firstframe is received via AUI and the network parameters are then output (AUI, 10 Mbps, halfduplex).

7/27/2019 BA_CP-1613-A2_76

17/24

5onfigurationNow configure the SIMATIC NET communications software to commission thecommunications processor. The rest of the procedure is described in the "CommissioningPC Stations" manual(Start menu Start ... Commissioning PC Stations).

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

18/24

Configuration

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

19/24

6echnical specificationsCP 1613 A2

The following technical specifications apply to the CP 1613 A2 communications processor:

Data transmissionTransmission rate 10/100 Mbps

InterfacesAttachment to Industrial Ethernet 15-pin D-sub socket with AUI and Industrial Twisted Pair

Connection to 10BaseT/100BaseTX RJ-45 connector

Connection to PC/PG PCI slot (3.3 V/5 V, 32 bits)

VoltagePower supply 5 V DC, +/- 5%;

12 V DC, +/- 5%

Current consumptionat +5 V max. 450 mA

at +12 V max. 500 mA

Permitted ambient conditionsOperating temperature +5 C to +55 C

Transportation/storage temperature -20 C to +60 C

ConstructionModule format PC card, short PCI format

Dimensions (H x W x D) in mm 107 x 21.6 x 167

Weight 140 g

Slot requirement PCI slot, short

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

20/24

7/27/2019 BA_CP-1613-A2_76

21/24

ApprovalsNoteThe specified approvals apply only when the corresponding mark is printed on thecommunications processor.

Electromagnetic compatibility - EMC directiveThe communications processor meets the requirements of the EC Directive:2004/108/EEC(EMC directive).

The communications processor is designed for use in the following areas:

Requirementsrea of applicationEmission Immunity

Residential areas, business and commercialoperations, and small businesses

EN 61000-6-3 EN 61000-6-1

Industrial environment EN 61000-6-4 EN 61000-6-2

EC declaration of conformityYou will find the EC declaration of conformity for this communications processor on theProduct Support pages under the following entry ID:


Machinery directiveThis communications processor is not a machine in the sense of the EC directive2006/42/EEC (Machinery Directive). There is therefore no declaration of conformity relatingto this EC Directive for the communications processor.

If the communications processor is part of the equipment of a machine, it must be included inthe procedure for obtaining the declaration of conformity by the manufacturer of the machine.

C-TICK approvalThe communications processor meets the requirements of the Australian AS/NZS 3548standard.

CP 1613 A2

http://support.automation.siemens.com/WW/view/en/63367995http://support.automation.siemens.com/WW/view/en/63367995

7/27/2019 BA_CP-1613-A2_76

22/24

Approvals

CP 1613 A2


CSA approvalThe communications processor has an approval in accordance with the Canadian CAN/CSA

C22.2 No. 60950-1 standard.

ICES conformityThe communications processor meets the requirements of the Canadian standard ICES-003.It is rated as a digital device of Class B ("Class B digital apparatus").

FCC approvalThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV technician for help.Siemens AG is not responsible for any radio television interference caused by unauthorizedmodifications of this equipment or the substitution or attachment of connecting cables andequipment other than those specified by Siemens AG. The correction of interference causedby such unauthorized modification, substitution or attachment will be the responsibility of theuser. The use of shielded I/O cables is required when connecting this equipment to any andall optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.

UL approvalThe communications processor has an approval in accordance with the US standard

UL 60950-1.

7/27/2019 BA_CP-1613-A2_76

23/24

Index

CComponents of the product, 5Configuring, 17Contact, 7

DDocumentation on the Internet, 5

GGlossary, 7

HHardware requirements, 9

IInstallation and connection, 15

LLED display, 9

PProduct features, 9Properties of the CP 1613, 9

SSIMATIC NET documentation, 6SIMATIC NET glossary, 7STEP 7, 13Support, 6

TTraining, 7

CP 1613 A2


7/27/2019 BA_CP-1613-A2_76

24/24

Index

CP 1613 A2

24 Operating Instructions 12/2012 C79000-G8976-C303-01

ba_cp-1613-a2_76

Documents