™

AVRprog programmer is a high performance tool used for programming

communicates to the microcontroller through a USB cable which is alsoused for powering the AVRprog programmer.

TO OUR VALUED CUSTOMERS

mikroElektronika.The primary aim of our company is to design and produce high quality electronic products and to constantly improve the performance thereof in order to better suit your needs.

The Atmel name and logo, the Atmel logo, AVR, AVR (Logo), AVR Freaks, AVR Freaks (Logo), AVR Studio, IDIC, megaAVR, megaAVR (Logo), picoPower ®, tinyAVR ® are trademarks of Atmel Coorporation.

Nebojsa MaticGeneral Manager

3

1.0. Introduction to AVRprog Programmer......................................................................................... 42.0. Dumping Code into the Microcontroller...................................................................................... 5

................................................................................................... 6................................................................................................................... 7

.......................................................................... 96.0. ................................................... 10

4

1.0. Introduction to AVRprog™ ProgrammerThe AVRprog ® ®

program and appropriate

AVRprog programmer.

The AVRprogAVRprog

Figure 1-1: AVRprog programmer Figure 1-2: AVRprog programmer

TheAVRprog The AVRprog

Figure 1-3:

Themicrocontroller to be programmed.

5

a hex code;

to be programmed and load the hex code;

Write button to dump code into the microcontroller. 3

1

2

3

Compiling program

2.0. Dumping Code into the MicrocontrollermikroBASIC PRO for

program.

12

6

The

TheWrite

bar in the bottom right corner

Device

The

Select the microcontroller to be programmed and the 1

microcontroller

2

Write optionmicrocontroller

3

1

2

3

the type of the microcontroller

Figure 3-1:

7

provided in the

CD Drive:

program free of charge from our

to proceed.

.

.

8

program in.

. If you

The

button.

to

9

illumination.

program

Start up the Device option in program

microcontroller.

button to open the Open Open

Write

10

Alt-EAlt-BAlt-W Write hex code into AVR microcontrollerAlt-V Verify loaded hex codeAlt-R Read program memoryAlt-D Change microcontroller typeCtrl-S

Ctrl-R

The

w Write to AVR microcontrollerv Verifyer Read program from AVR microcontroller pfcfd

FUSE:0x.....q program after programming

DISCLAIMER

All the products owned by MikroElektronika are protected by copyright law and international copyright treaty. Therefore, this manual is to be treated as any other copyright material. No part of this manual, including product and software described herein, may be reproduced, stored in a retrieval system, translated or transmitted in any form or by any means, without the prior written permission of MikroElektronika. The

manual is prohibited.

MikroElektronika provides this manual ‘as is’ without warranty of any kind, either expressed or implied,

purpose.

MikroElektronika shall assume no responsibility or liability for any errors, omissions and inaccuracies that may

of this manual or product, even if MikroElektronika has been advised of the possibility of such damages. MikroElektronika reserves the right to change information contained in this manual at any time without prior notice, if necessary.

HIGH RISK ACTIVITIES

The products of MikroElektronika are not fault – tolerant nor designed, manufactured or intended for use or resale as on – line control equipment in hazardous environments requiring fail – safe performance, such as

life support machines or weapons systems in which the failure of Software could lead directly to death, personal injury or severe physical or environmental damage (‘High Risk Activities’). MikroElektronika and its

TRADEMARKS

The Mikroelektronika name and logo, the Mikroelektronika logo, mikroC, mikroC PRO, mikroBasic, mikro--

of Mikroelektronika. All other trademarks mentioned herein are property of their respective companies.

All other product and corporate names appearing in this manual may or may not be registered trademarks

©MikroelektronikaTM

If yo

u w

ant t

o le

arn

mor

e ab

out o

ur p

rodu

cts,

ple

ase

visi

t our

web

site

at w

ww

.mik

roe.

com

If yo

u ar

e ex

perie

ncin

g so

me

prob

lem

s w

ith a

ny o

f our

pro

duct

s or

just

nee

d ad

ditio

nal i

nfor

mat

ion,

ple

ase

plac

e yo

ur ti

cket

at

ww

w.m

ikro

e.co

m/e

n/su

ppor

t