No. :WXXS-000-GGSY-14

NO. DATE PAGE SANYO SIGNED CLIENT SIGNED

USER:DALIAN SANYO COMPRESSOR CO., LTD.

LEADER TECHNICALMANAGER APPROVED CHECKED SUBMITTED

MANUFACTURER:

PURCHASINGMANAGER

SPECIFICATIONS OF HERMETIC SCROLL COMPRESSOR

C-SCP270H38A

REVISION RECORD

REVISION DETAILS

APPROVAL SHEET

MODEL

1

Phase

Rated Voltage

Rated Frequency

Motor Type

Number of Poles

Electrical Insulation

Nominal Revolution

Locked Rotor Ampere

Suction Line (O.D.)

Discharge Line (O.D.)

Notes

1 Voltage range is applied at standard rating conditions.

2 Motor specifications in the table are the average values for your reference.

3 ( ): All units with parentheses are reference values.

Expiration of Specification

Expiration of this specification shall be effected until issuing a notice with indication of the expiration date from the

issued date . In case of improvement or elimination of this specification , it shall be handled by the revision record

based on agreement between both sides.

Compressor Model — C-SCP270H38A

Black Paint

min-1 —

A 106/111

U-W 1.373

Connection Tube

U-V 1.308

mm (in) 25.4 (1.000)

mm (in) 19.05 (0.750)

V-W 1.351

ml (fl oz) 2800 (94.7)

Displacement cm3 (in3) /rev 89.2(5.44)

— R410A

Oil Type — FV68S or Equivalent

Refrigerant

V 342~456/396~484

kg (lb) 66.5(146.6)

— Natural Cooling

Power Source

— 3

V 380-415/440

Hz 50/60

Compressor Cooling Type

°C (°F) -15~12 (5~54)

— Hermetic Scroll Compressor

— High Back Pressure

Content Unit Specification

Section 1. General Specifications

Voltage Range

Weight (Including Oil)

Oil Charge

Type

Application

Evap. Temp. Range

E

— 3-PH Induction Motor

— 2

Class

Compressor Surface Paint —

Motor

Winding Resistance[at 25°C (77°F）] Ω

2

Hz 50 60

V 380 440

W 22,400 27,200 ±5%

(BTU/hr) 76,429 92,806 reference

W 7,400 8,900 ±5%

A 13.1 13.4 ±5%

Standard Rating Conditions

°C (°F)

°C (°F)

°C (°F)

°C (°F)

°C (°F)

Hz 50

V 380

dB(A) 72Max.

Notes

1 The operating conditions are the same as 2.1.

2 MIC location is the distance of 1m (3.28feet) from the compressor.

3 Sound Level is an average sound pressure level in four directions.

Hz 50

V 304

Conditions

°C (°F)

°C (°F)

MPa(G)/psig

MPa(G)/psig

UnitL.P. S. MPa(G)/psigH. P. S. MPa(G)/psig

MΩ

V

mgNote:

1. The insulation resistance be measured with a DC500V megohm tester.

0.9(130.5)

2.3 Minimum Starting Voltage

2.2 Sound Level

10~60(50~140)

10~40(50~105)

3.25(471)

7.2( 45 )

Remark

2.1 Performance

Section 2. Performance Warranty

Power Source (3PH)

54.4(130)

Capacity

2.21(320)

2.4 OthersContent Specification

Residual Moisture

Insulation Resistance

Dielectric Strength

Design Pressure4.15(602)

100 (without refrigerant)

2300 (1 second)

400

Input Power

Current

Condensing Temp.

Evaporating Temp.

Suction Gas Temp.

Liquid Temp.

Ambient Temp.

Power Source (3PH)

Ambient Temp.

High Pressure

Low Pressure

Sound Level

Power Source (3PH)

Minimum Starting Voltage

Compressor Temp.

18.3( 65 )

46.1(111)

35.0( 95 )

352

60

440

74Max.

60

3

3.1 Accessories List

Parts Name Qty Parts code Revision No. Note

Terminal Box Cover 1 A-0101-DSB 0 Installed on Compressor

Terminal Box Clip 1 A-0201-DSB 0 Installed on Compressor

Insulating Grommet 1 A-0301-DSB 0 Installed on Compressor

Gasket Terminal 1 A-0401-DSC 0 Installed on Compressor

Mounting Grommet 4 M-0101-DSC 0 Included with Compressor

Mounting Sleeve 4 M-0201-DSC 0 Included with Compressor

3.2 The Drawing for Reference

Revision No.

0

0

0

0

3. 3 Inernal Motor Protector (in compressor)

Parts Name

Trip Temprature

Reset Temprature

Trip Current

Inernal Motor Protector 70±10

Parts Code

D-0105-DSC

D-0201-DSC

Specification

66A / 3~10s

165±5

E-0910-DSC

Section 3. Standard Accessories

Wiring Diagram

Compressor Outline Drawing

Parts Name

Mounting Parts Listing

Packing Dimensions

M-5102-DSC

4

4.1 Protection Required but not Included with compressor

Protection Device Items

Features

Rated Voltage

Crankcase Heater Rated Power

Mounting Position

Trip Temperature

Reset Temperature

High Pressure Switch Setting

Low Pressure Switch Setting

4.2 Position of the Protection and Refrigerant Charging

135±5(275 ±10 °F)

Section 4. Compressor Protection

Specifications

Cut-out seting no lower than 0.15MPa(G)

AC380VReversal Defensible Relay

To protect the compressor from reverse rotation

Cut-out seting no higher than 4.15MPa(G)

86±15 (187 ± 27 °F)

Discharge Thermostat

88 Watts

Located in the well pipe of top shell

HIGH PRESSURE

SWITCH

COMPRESSOR

LOW PRESSURE

SWITCH

CRANKCASE HEATER

DISCHARGE THERMOSTAT

OUTDOOR HEAT

EXCHANGER

INDOOR HEAT

EXCHANGER

ACCUMULATOR

FOR LIQUID REFRIGERANT

CHARGING

FOR GAS REFRIGERANT

CHARGING

CAPILLARY

LIQUID LINE SERVICE

VALVE

GAS LINE SERVICE VALVEREVERSING

VALVE

5

6

Section 5. Operating Envelope

10

20

30

40

50

60

70

-30 -25 -20 -15 -10 -5 0 5 10 15 20

Evaporating Temperature（）

Con

dens

ing

Tem

pera

ture（

）

Suction Gas Superhea : 11.1K.Refrigerant : R410A.

Transient Operation

Normal Operation

The following requirements apply to vertical type hermetic scroll compressors:

No. Item Note

1 Refrigerant

4 Compression Ratio

5 Winding Temp.

8 Suction Gas Temp.

It should meet therequirement of item 5, 6,7 and 14 within 30cm ofthe suction fitting.

12 Refrigerant Charge Specific gravity of theOil:0.94

13 Life Time

By high pressure switch

By low pressure switch

16 System MoistureLevel

18 Tilt

Operation beyond the above limits must be approved by Dalian SANYO Compressor Co., Ltd. (G): Gauge Pressure

Voltage at compressorterminals.

Single Phase Models: 90% of the rated voltage min.

For at least 7 minutes -on/3 minutes-off isrecommendable.

On Period: Until the oil level returns to the center of the lower bearing

Off Period: Until balance of high and low pressure is obtained

Voltage at compressorterminals.

24 hrs. after vacuuming:1.01kPa Max.

Condensing Temp.

Discharge GasTemp.

11 On/Off Cycling

6 Shell Bottom Temp.

2 ~ 6 8

Limit: Applicable to transitional brief period of time, such as start-up and beginning of defrost mode.

90(194 °F) Max.

Evaporating Temp.+12(21 °F) Min.

Ambient Temp.+11(20 °F) Min.

115(240 °F) Max. 125(257 °F)

14 Minimum Oil Level

Section 6. Application Standard & Limit

2 Evaporating Temp.

Standard Limit

R410A

Standard: Applicable to ordinary conditions in Japan JIS B8616 or standards relative to JIS B8616, such as standard ratingconditions, maximum operating conditions, low temperature conditions, etc.

17SystemUncondensable GasLevel

Abnormal PressureRise/Drop15

9 Running Voltage

200ppm Max.

No excessive noiseSuperheat: 5K(10 °F)Min.

Within ±10% of the rated voltage

oil/refrigerant(wt.)≥0.35

Pressure Drop: 0.15MPa(G) (22psig) Min.

10 Starting Voltage

5。Deg.Max.

200,000 cycle

Residual Oxygen 0.1 Vol.% Max.

1 Vol.% Max.

Pressure Rise: 4.15MPa(G) (602psig) Max.

C-SC:No less than 70% of the initial oil charge

C-SB: Center of the lower bearing C-SB:Bottom of the lower bearing

115(240 °F) Max.

C-SB:130( 266°F) Max.

C-SC:135( 275°F) Max.

Three Phase Models: 85% of the rated voltage min.

7

-15~12(5～54 °F) -25~15(-13～59 °F)

0.38~1.06MPa(G)(55～154psig) 0.23~1.16MPa(G)(33～168psig)

30~60(86～140 °F) 65(149 °F)

4.18MPa(G)(606psig)1.80~3.75MPa(G)(261～544psig)3

7

1 Installation should be completed within 15 minutes after removing the rubber plugs.

2 Do not use the compressor to compress air.

5 Do not tilt over the compressor while carrying it.

6 Do not remove the paint.

9 Do not operate compressor in reverse rotational direction.

11 Copper Piping Stress Start/Shutdown 34.32 N/mm2 Max.

Run 12.26 N/mm2 Max.

10 Suction strainers are recommended for all applications.

3 Do not energize the compressor under vacuumed conditon.

Notes

4 Evacuation and Refrigerant charge ： Evacuate internal section in the refrigeration system from high and low pressuresides and charge liquid refrigerant from condenser outlet side. Additional charge shall be done with gas condition fromlow side.

7 Crankcase heater is required when the oil sump temperature is too low to meet the requirement of item 6 on page7.

8 Voltage fluctuation between compressor terminals, during operation, shall be within 2% of the rated voltage.

8

Voltage drop may occur due to the large current draw during compressor starting.

We recommend selecting the wire size from the table below.

7.1 Type of Unit7.1.1 Window & Commercial Type Unit

7.1.2 Split Type(Separate Type)

7.2 Size Table of Electrical Wire

Remark③（heat-resistance Temperature:120°C(248°F) min.）

5m max. 10m max. 15m max. 20m max. 30m max. 50m max. 1m max.

20max. 2.0 2.0 2.0 3.5 5.5 8.0 2.0

30max. ↑ ↑ 3.5 5.5 ↑ 14.0 ↑

40max. ↑ 3.5 5.5 ↑ 8.0 ↑ ↑

50max. ↑ ↑ ↑ 8.0 14.0 22.0 ↑

60max. ↑ 5.5 ↑ ↑ ↑ ↑ ↑

70max. 3.5 ↑ 8.0 14.0 ↑ ↑ 3.5

80max. ↑ ↑ ↑ ↑ 22.0 30.0 ↑

90max. ↑ ↑ 14.0 ↑ ↑ ↑ ↑

100max. ↑ 8.0 ↑ ↑ ↑ 38.0 ↑

110max. ↑ ↑ ↑ ↑ ↑ ↑ ↑

120max. 5.5 ↑ ↑ 22.0 30.0 ↑ ↑

140max. ↑ 14.0 ↑ ↑ ↑ 50.0 5.5

160max. ↑ ↑ 22.0 ↑ ↑ ↑ ↑

180max. ↑ ↑ ↑ ↑ 38.0 60.0 8.0

200max. 8.0 ↑ ↑ 30.0 ↑ ↑ ↑

220max. ↑ ↑ ↑ ↑ 50.0 80.0 ↑

240max. ↑ ↑ ↑ ↑ ↑ ↑ 14.0

The internal motor protector does not protect the compressor against all possible conditions.

Please be sure that the system utilizes the ground connection when installed in the field.

Section 7. Selection of Electrical Wire

7.3 Caution of Ground

Starting current(A)

Size of electrical wire（mm2）

Remark ① or Remark ①+②（heat-resistance Temperature: 60°C(140°F) min.）

①power source

terminal plate compressor

indoor

outdoor

②

①powersource

terminalplate

compressorindoor

outdoor

② ③

9

TAPPING SCREWS M4

77.2

TERMINAL

U

V

W

68.2

COMP. CODE A B C D E809 28* 8*809 18* 8*809 29* 8*809 19* 8*809 20* 8*809 10* 8*809 22* 8*809 12* 8*C-SCP270,315,360,400

538[21.18]

284[11.18]

486[19.13]

7.9[0.31]

289[11.38]

553[21.77]

299[11.77]

501[19.21]

9[0.35]

304[11.97]

Part CodeD-0105-DSC D-0105-DSC

Name Compressor Outline Drawing

10

COMP. CODE A B C D E809 28* 8*809 18* 8*809 29* 8*809 19* 8*809 20* 8*809 10* 8*809 22* 8*809 12* 8*C-SCP270,315,360,400

538[21.18]

284[11.18]

486[19.13]

7.9[0.31]

289[11.38]

553[21.77]

299[11.77]

501[19.21]

9[0.35]

304[11.97]

No. Part QTY Name1 M-0101-DSC 4 Mounting Grommet2 M-0202-DSC 4 Mounting Sleeve

11

Part Code M-5102-DSC Name Mounting Parts Listing

1

`

Compressor Model AC-SCP270H38*C-SCP315H38*C-SCP360H38*C-SCP400H38*

Part Code

D-0201-DSC

Name Packing Dimensions

12

697 [27.441]

E-0910-DSCName

13

Part Code

Wiring Diagram

POWER SUPPLY50Hz 220V

DISCHARGE GAS TEMP. SENSOR

W

V

U

POWER SUPPLY50Hz 380~415V

14

11

12

A

B

C

T

S

R

CRANKCASE HEATER

REVERSAL DEFENSIBLE RELAY

MAGNETIC SWITCH

COMPRESSOR

INTERNAL PROTECTOR

SWITCH

TERMINAL

PERFORMANCE DATA (PRELIMINARY DATA)C-SCP270H38A

Power Source 3PH 50Hz 380～415VSuction Gas Superheat(K) 11.1Sub Cooling(K) 8.3Compressor Cooling Natural CoolingRefrigerant R410A

CAPACITY(W)CondensingTemperature() -15 -10 -5 0 5 10 15

35.0 13,083 15,487 18,376 21,834 25,940 30,77840.0 12,376 14,656 17,385 20,644 24,515 29,081 34,42245.0 11,741 13,898 16,465 19,527 23,163 27,456 32,48850.0 11,179 13,212 15,619 18,482 21,883 25,904 30,62655.0 12,599 14,845 17,510 20,676 24,424 28,83760.0 14,144 16,611 19,541 23,017 27,12065.0 15,784 18,479 21,683 25,477

POWER(W)CondensingTemperature() -15 -10 -5 0 5 10 15

35.0 5,712 5,345 5,077 4,899 4,802 4,77840.0 5,963 5,711 5,532 5,415 5,353 5,337 5,35845.0 6,296 6,159 6,068 6,013 5,986 5,978 5,98150.0 6,711 6,690 6,686 6,693 6,701 6,701 6,68655.0 7,302 7,387 7,456 7,498 7,507 7,47360.0 8,171 8,300 8,378 8,395 8,34365.0 9,227 9,340 9,365 9,295

CURRENT(A) @380VCondensingTemperature() -15 -10 -5 0 5 10 15

35.0 10.2 9.8 9.5 9.3 9.2 9.140.0 10.7 10.4 10.2 10.1 10.0 10.0 10.045.0 11.3 11.2 11.1 11.0 11.0 11.0 11.050.0 11.9 12.0 12.0 12.0 12.1 12.1 12.055.0 12.9 13.0 13.2 13.2 13.3 13.260.0 14.2 14.4 14.5 14.5 14.565.0 15.7 15.9 15.9 15.8

NOTE:* The performance values subject to change without notice.

Compressor Model

Evaporating Temperature()

Evaporating Temperature()

Evaporating Temperature()

C-SCP270H38APower Source 3PH 50Hz 380～415VCompressor Model(Code)

0

5,000

10,000

15,000

20,000

25,000

30,000

35,000

40,000

‐15 ‐10 ‐5 0 5 10 15

CAPA

CITY

(W)

Evap. Temp. ()

CAPACITY Cond.Temp.

35.040.545.050.054.460.065.0

6.0

8.0

10.0

12.0

14.0

16.0

18.0

‐15 ‐10 ‐5 0 5 10

CURR

ENT (A)

Evap. Temp. ()

CURRENT @ 380V Cond.Temp.

65.060.054.450.045.040.535.0

COEFFICIENTS OF PERFORMANCE CURVES

Compressor Model C-SCP270H38APower Source 3PH 50Hz 380～415VSuction Gas Superheat (K) 11.1Sub Cooling (K) 8.3Compressor Cooling Natural CoolingRefrigerant R410A

X——CAPACITY(W) OR POWER(W) OR CURRENT(A) OR FLOW(kg/h)S——EVAPORATING TEMP, °CD——CONDENSING TEMP, °C

380V-50HzC1C2C3C4C5C6C7C8C9

C10

Note:The polynomial coefficients subject to change without notice.

X=C1+C2*(S)+C3*D+C4*(S2)+C5*(S*D)+C6*(D2)+C7*(S3)+C8*(D*S2)+C9*(S*D2) +C10*(D3)

CAPACITY (W) POWER (W) CURRENT (A)3.219596E+04 3.593062E+03 6.370747E+00

1.056983E+03 -9.479755E+01 -1.256042E-01

-3.469117E+02 -2.027454E+01 1.274237E-02

1.819444E+01 5.358398E+00 6.906110E-03

1.645550E+00 2.015232E-03

1.089955E-01 -1.132851E-02 -1.130512E-05

-3.344003E-06 -1.454315E-06 -1.630045E-09

-1.487040E-01 -1.066712E-01 -1.433611E-04

5.563710E-07 -6.273563E-07

-8.665679E+00 1.930288E+00 2.638099E-03

-7.456751E-10

1.452823E+00