ansi-z535-2-2002-safey-signs[1]

ANSI Z535.2-2007

American National Standard

for Environmental and Facility Safety Signs

Copyright National Electrical Manufacturers Association Provided by IHS under license with NEMA Licensee=Chevron API Emergency/1000001116

Not for Resale, 01/30/2009 05:18:07 MSTNo reproduction or networking permitted without license from IHS

--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

American National Standard AMERICAN NATIONAL STANDARD FOR ENVIRONMENTAL AND FACILITY

SAFETY SIGNS

Secretariat: National Electrical Manufacturers Association Approved September 12, 2007 Published November 15, 2007 American National Standards Institute, Inc.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. NEMA standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process and establishes rules to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, express or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or seller’s products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

i

AMERICAN NATIONAL STANDARD

Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The use of American National Standards is completely voluntary; their existence does not in any respect preclude anyone, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute.

Published by National Electrical Manufacturers Association 1300 North 17th Street, Rosslyn, VA 22209 © Copyright 2007 by National Electrical Manufacturers Association All rights reserved including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American Copyright Conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

ii

This page intentionally left blank.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

iii

Contents

Page

Foreword ............................................................................................................................i 1 Introduction.................................................................................................................... 1 2 Scope and Purpose ....................................................................................................... 2 2.1 Scope................................................................................................................ 2 2.2 Purpose ............................................................................................................ 2 3 Application and Exceptions ........................................................................................... 2 3.1 Application ........................................................................................................ 2 3.2 Exceptions ........................................................................................................ 2 4 Definitions ............................................................................................................. 3 5 Safety sign colors and formats ...................................................................................... 5

5.1. DANGER signs................................................................................................. 5

5.2. WARNING signs............................................................................................... 6

5.3. CAUTION signs ................................................................................................ 6

5.4. NOTICE signs................................................................................................... 7

5.5. Signs for safety instruction or safety equipment location ................................. 7

5.6. Fire safety signs ............................................................................................... 8

5.7. Directional arrow signs ..................................................................................... 9

5.8. Special signs .................................................................................................... 9

5.9. Sign classification selection.............................................................................. 9 6 Sign design/layout ....................................................................................................... 10 6.1 Three panel signs ........................................................................................... 10 6.2 Two panel signs.............................................................................................. 10 6.3 Application of sign formats by hazard classification....................................... 10 7 Sign color specifications .............................................................................................. 10 8 Safety Symbols ........................................................................................................... 10 8.1 General. .......................................................................................................... 10



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

iv

8.2 Safety symbol use .......................................................................................... 11 9 Letter style and size..................................................................................................... 11

9.1 Letter style ...................................................................................................... 11

9.2 Letter size ....................................................................................................... 11

10 Sign finish ........................................................................................................... 11

11 Sign Placement ........................................................................................................... 11 12 Illumination ........................................................................................................... 12

13 Normative References................................................................................................. 12

Figures

1 The safety alert symbol ................................................................................................. 4

2 Format for the DANGER signal word panel .................................................................. 5

3 Format for the WARNING signal word panel ................................................................ 6

4 Format for the personal injury CAUTION signal word panel ......................................... 6

5 Format for the CAUTION signal word panel not related to personal injury when used as an alternate to NOTICE ..........................................................................................................7

6 Format for the NOTICE signal word panel .................................................................... 7

7 Formats of signal word panels used for safety instruction and safety equipment location signs .......................................................................................................................... 8

8 Example of fire extinguisher location sign ..................................................................... 9

9 Directional arrow (indicating movement to the right) ..................................................... 9

10 Examples of signal word panels with various safety alert symbols—three-panel sign horizontal format.......................................................................................................... 13

11 Three-Panel Sign—vertical format ............................................................................. 14

12 Two-Panel Sign—vertical format ................................................................................ 14

13 Three-Panel Sign—horizontal format ......................................................................... 15

14 Two-Panel Sign—horizontal format ............................................................................ 15

15 Two-Panel Sign—shortened signal word panel format .............................................. 15

16 Two-Panel Sign—side-by-side format ........................................................................ 15



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

v

17 Three-Panel Sign—horizontal format with symbol panel on right ............................... 16

18 Three-Panel Sign—horizontal format with message panel and symbol panel separated by line ........................................................................................................... 16

19 Three-Panel Sign—horizontal format with message panel and symbol panel separated by white space ........................................................................................................... 16

20 Figure 20 – Two-Panel Sign—signal word panel and symbol pane............................ 16

21 Two-Panel Sign—vertical format with message above symbol panel......................... 17

22 Two-Panel Sign—vertical format with message below symbol panel ......................... 17

Tables

1 Application of sign panel formats ................................................................................ 10

Informative Annexes

A Guidelines for increasing recognition of safety sign components ............................... 18

B Principles and guidelines for the design of environmental and facility safety signs.... 20

C Previous formats for signal word panels ..................................................................... 30

D Risk estimation and signal word selection................................................................... 31

E Informative references................................................................................................. 38



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

vi

Foreword (Neither this foreword nor any of the informative Annexes is a part of American National Standard Z535.2-2007.) This standard is one of six standards maintained and revised by the ANSI Z535 Committee. The six standards are: Z535.1 – Safety Color Code Z535.2 – Environmental and Facility Safety Signs Z535.3 – Criteria for Safety Symbols Z535.4 – Product Safety Signs and Labels Z535.5 – Safety Tags and Barricade Tapes (for Temporary Hazards)

Z535.6 – Product Safety Information in Product Manuals, Instructions, and Other Collateral Materials

This standard was formulated to provide a visual alerting system to aid in identifying potential hazards known to exist in the environment. Together, ANSI Z535.1, Z535.2 and Z535.3 contain information needed to specify formats, colors, and symbols for safety signs used in environmental and facility applications. The ANSI Z535.4 and Z535.5 standards are harmonized with this standard to provide appropriate hazard avoidance information for products that might be encountered in the environment (ANSI Z535.4) or temporary changes to the environment (ANSI Z535.5). It is desirable that new signs, symbols and colors for environmental and facility safety signs specified after the approval of this standard comply with the standard. The ANSI Z35 Committee on Safety Signs and ANSI Z53 Committee on Safety Colors were combined in 1979 to form the ANSI Z535 Committee on Safety Signs and Colors. The ANSI Z535.4 Standard addresses the design of safety signs and labels for application to products, and was first published in 1991. In that Standard, the format specified for the signal word panel was a simple rectangle. The rectangle contained the Safety alert symbol, a signal word (DANGER, CAUTION or WARNING), and specific safety colors were designated to be used with those signal words (DANGER/ Safety Red; WARNING/ Safety Orange; CAUTION/ Safety Yellow.) This contrasted with the longstanding format of the black rectangle with red oval and white letters used for danger signs. The initial impetus for the new ANSI Z535.4-1991 header format was that products often had limited space for a sign or label and omitting the older format allowed bigger letters for the signal word. The ANSI Z535.2-1991 standard retained the longstanding danger heading format and created a similar format (using a truncated diamond) for the new warning sign head. Each 1991 standard allowed the user to use the format of the other standard if desired. The ANSI Z535.2-1998 standard showed the preferred format for environmental and safety signs to be the simple header style of the ANSI Z535.4 standard for product safety signs and labels; both standards included the older system. The ANSI Z535.2-1998 standard also stated a preference to use a white background for the message panel, in order to increase contrast and viewing distance. Like the ANSI Z535.4 standard, the Z535.2-1998 standard also required the sign to give information of the consequences of not avoiding the hazard, if the consequence is not obvious. The ANSI Z535.2-1998 standard was carefully crafted so that the new requirements scheduled to become mandatory in the 2002 Edition were stated as preferred in the 1998 Edition. As of the 2002 standard, the older format is no longer included; the simple header with larger letters and more referential color is set forth. The ANSI Z535.2-2007 includes definitional changes and safety alert symbol formats intended to clarify the distinction between signal words and greater harmonization with international standards. The 2007 edition started the process of eliminating the use of the CAUTION signal word panel without the safety alert symbol for procedures not related to personal safety, such as property damage. The preferred signal word is NOTICE. The use of CAUTION for that purpose will be phased out in the 2011 Edition.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

vii

There are five Annexes to this standard, including a new annex of informative references. An annex on risk assessment and choice of signal words was also added in 2007. This Foreword and all of the Annexes are considered to be informative and not an official part of this standard. In the vocabulary of writing standards, the word “informative” is meant to convey that the information presented is for informational purposes only and is not considered to be mandatory. The body of this standard is “normative”, meaning that this information is considered to be mandatory. See the ANSI Z535.1-2006 Safety Color Chart for the purpose of viewing accurate colors. Due to the differences in color printing technologies and color monitors, the appearance of colors in this document may not be accurate.

This standard was processed and approved for submittal to ANSI by the Accredited Standards Committee on Safety Signs and Colors, ANSI Z535. Committee approval of this standard does not necessarily imply that all committee members voted for its approval. At the time it approved this standard, the Z535 Committee had the following members: Gary M. Bell, Chairperson Paul Orr, Secretary Organization Represented: Name of Representative: American Society of Safety Engineers J. Paul Frantz Thomas F. Breshnahan (Alt.) Howard A. Elwell (Alt.) American Welding Society August F. Manz Applied Materials Edward Karl Carl Wong (Alt.) Applied Safety and Ergonomics, Inc. Steven Hall Stephen Young (Alt.) Association for Manufacturing Technology David Felinski Association of Equipment Manufacturers Richard A. Dressler Dan Taylor (Alt.) Browning Arms Company Larry D. Nelson Caterpillar, Inc. Sue A. Hooker Mark A. Stephen (Alt.) Clarion Safety Systems, LLC Geoffrey Peckham Jerry Reganess (Alt.)



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

viii

Dorris & Associates, Inc. Nathan T. Dorris Alan Dorris (Alt.) Eagle Crusher Co. Ryan Parsell Edison Electric Institute Janet Fox Glass Application Analysis, Inc. William P. Whitney Hale Color Consultants, Inc. William N. Hale Human Factors & Ergonomics Society Michael Kalsher Michael S. Wogalter (Alt.) Human Factors & Safety Analytics, Inc. B. Jay Martin Husqvarna Outdoor Products, Inc. Brett E. Cohen Industrial Safety Equipment Association Janice Comer Bradley Richard Fisk (Alt.) Russell Goldman II (Alt.) Carmen Taylor (Alt.) Institute of Electrical & Electronics Engineers Al Clapp John Dagenhart (Alt.) Sue Vogel (Alt.) International Staple, Nail, and Tool Association John W. Kurtz L. Dale Baker & Associates L. Dale Baker Lab Safety Supply, Inc. Jim Versweyveld Marhefka & Associates Russell E. Marhefka National Association of Graphic Product Russ Butchko Identification Manufacturers Donna Ehrmann (Alt.) National Electrical Manufacturers Association John Young John Katzbeck (Alt.) National Spray Equipment Mfrs. Assoc. Dan Pahl Power Tool Institute Wayne Hill Mark Hickok (Alt.)



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

ix

Rural Utilities Service Trung Hiu Safety and Forensic Enterprises, LLC Loren Mills Safety Behavior Analysis, Inc. Shelley Waters Deppa Sauder Woodworking Company Gary Bell Scaffold Industry Association Dave Merrifield Snap-On-Tools Bill Pagac Dan Eggert (Alt.) Society of the Plastics Industry, Machinery Div. Walter Bishop Bob Monteith (Alt.) Standard Register Corp. James Heckman Linda LeBlanc (Alt.) System Safety Society Robert J. Cunitz Underwriters Laboratories Richard Olesen Whirlpool Corporation Joanie M. Gentry Donald Grob (Alt.) Subcommittee Z535.2 on Environmental and Facility Safety Signs, which developed the 2007 standard, had the following members: Allen L. Clapp, Chair John Dagenhart, Vice-Chair Paul Orr, Secretary Dale Baker Julie Bandt Gary Bell Quinn Brackett Blair Brewster Robert Cunitz Alan Dorris Robert Fisk Brian Grieser Trung Hiu B. Jay. Martin Loren Mills Linda Moquet Richard Olesen Geoff Peckham Sharon White Michael Wogalter David Young



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

x

This page intentionally left blank.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

1

AMERICAN NATIONAL STANDARD FOR ENVIRONMENTAL AND FACILITY SAFETY SIGNS 1 Introduction

This standard covers requirements for environmental and facility safety signs that are to be used to visually alert and inform observers of potential hazards in the environment or facility. See ANSI Z535.4-2007 for the requirements for product safety signs and labels.

Sometimes the actions required to avoid the hazard or the consequences of not avoiding the hazard are not obvious to the viewer from the context in which the sign is used. In such situations viewer training, additional messages, or the use of safety symbols on the sign should be used to provide this information. To achieve these objectives, it is most important to have an easily recognizable and highly conspicuous hazard alerting system such as is presented in this document.

The diversity of culture and background in the American society increases the need to standardize a visual alerting identification system for safety signage. The great need to eliminate accidents and suffering among individuals who may be exposed to hazards requires the use of standard formats, sizes, colors, shapes, and a firm understanding of the degree of hazard. This document contains the elements that designate a separation between levels of hazard severity.

This standard sets forth a hazard alert system that uses different signal words and colors to distinguish between levels of hazards. Use of this standard will allow observers of environmental and facility safety signs to determine the type and degree of hazards and take appropriate actions to avoid injury.

To promote standardization and increase effectiveness, the formats used in this standard are intentionally similar to those used in ANSI Z535.4-2007 Standard for Product Signs and Labels. While these standards are similar in many respects, they each address different physical and visual requirements. As a result, there are basic differences between environmental/facility safety signs and product safety signs. Environmental and facility safety signs are usually larger and observed at longer distances; they frequently contain lesser amounts of information for visual clarity at a distance. Product safety signs are likely to contain more information within a smaller format, are usually observed at closer distances, and must physically and visually integrate with a wide range of product size, shape and color characteristics. The Z535 Committee on Safety Signs and Colors has recognized and affirmed the need for these two standards.

The ultimate application of the visual alerting messages will be up to those responsible for affixing these messages. This standard is intended to provide specifications for signs to convey a safety alert message that is clearly and rapidly understood regardless of the viewers’ background. In certain areas of the country where other languages are used, consideration should be given to providing messages in those languages.

AMERICAN NATIONAL STANDARD ANSI Z535.2-2007



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

2

2 Scope and purpose

2.1 Scope

This standard establishes requirements for a uniform visual system of identification related to potential hazards in the environment. It provides for the design, application and use of signs and placards employing this visual alerting system.

2.2 Purpose

The primary purpose of this standard is to provide an effective means of communicating information concerning environmental hazards to the observer, so that injury resulting from the hazard(s) can be avoided. To this end, this standard establishes a uniform and consistent visual layout intended to limit proliferation of safety sign designs and achieve a national system to promote recognition and avoidance of hazards. In addition, communication of other important information for the safety and well-being of the observer is also included. To do this effectively, it is necessary to minimize the number of layouts and design formats while providing flexibility to meet individual consumer needs and situations.

2.2.1 This standard covers safety signs used at fixed locations in the environment such as industrial facilities, as well as larger, movable signs that may be used on a temporary basis. For the requirements of accident prevention tags, safety-alerting tapes, etc., used with temporary hazards, see ANSI Z535.5-2007 Safety Tags and Barricade Tapes (for Temporary Hazards)

2.2.2 There are a number of existing American National Standards which are recognized for particular industries or specific uses. Compliance with these standards may be considered for such particular industry or use. It is not the intent of this ANSI Z535.2 standard to replace existing standards or regulations, which are uniquely applicable to a specific industry or use. It is the intent to encourage adoption of this standard in subsequent revisions of other standards and regulations.

2.2.3 This standard is issued with the objective of minimizing the proliferation of non-standard hazard alerting devices and achieving application of a national uniform system for the recognition of hazards in the environment. Where portions of other standards and regulations can be modified to reflect the concepts of this standard, such modifications should be made.

3 Application and exceptions

3.1 Application

This standard provides guidance for industries, commercial establishments, property owners, employers and others who have a desire to alert persons to potential personal injury hazards or property damage hazards inherent in the environment or facility under their control.

3.2 Exceptions

3.2.1 Should any of the requirements of this standard conflict with federal, state, or municipal regulations, such conflict shall not invalidate other sections of this standard.

3.2.2 These requirements do not include labels or signs for products, containers of chemicals and chemical mixtures and hazardous substances, in-plant vehicular movement and way-finding signs (except as defined in section 5.8) public streets and highways, railroads, air transport, marine operations, exit signs, identification of piping or process valves, or safety bulletins and posters.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

3

4 Definitions

4.1 accident: An incident that results in unintended harm.

4.1.1 harm: Death, injury or property damage.

4.1.2 incident: An unintended and undesired event that has the potential to cause harm.

4.2 color: Colors specified in this standard shall conform to ANSI Safety Color Code, Z535.1-2006

4.3 decal: See safety sign.

4.4.1 hazard: A potential source of harm.

4.5 intent:

4.5.1 may: This word is understood to be permissive.

4.5.2 shall: This word is understood to be mandatory.

4.5.3 should: This word is understood to be advisory.

4.5.4 informative: Refers to those portions of this Standard provided only for purposes of clarification, illustration, and general information. Those portions of the standard considered informative do not contain mandatory requirements. The Foreword and all of the Annexes are considered informative.

4.5.5 normative: Refers to those portions of the Standard containing the mandatory requirements (shall), as well as recommended practices (should). The body of this standard is considered normative.

4.6 label: See safety sign.

4.7 panel: Area of a safety sign having a distinctive background color different from adjacent areas of the sign or which is clearly delineated by a line, border or white space. Three (3) types of panels a safety sign may use are: signal word, message, and safety symbol. See Table 1 and Figures 10 – 21.

4.7.1 signal word panel: Area of a safety sign that contains the signal word or words. For personal injury hazards, the signal word panel shall contain the safety alert symbol.

4.7.2 message panel: Area of a safety sign that contains those words related to: identification of the hazard, how to avoid the hazard, and/or the probable consequences of not avoiding the hazard. The order in which the content appears in the message panel is flexible. Factors to consider when determining the order of a word message’s content include the target audience’s degree of prior knowledge of the hazard and the reaction time required to avoid the hazard. When information on consequence, avoidance, or type of hazard is readily inferred, this information may be omitted from the message panel. See Annex B 3.1. 4.7.3 safety symbol panel: Area of a safety sign that contains the safety symbol.

4.8 placard: See safety sign.

4.9 safety alert symbol: (See Annex A.) A symbol which indicates a potential personal injury hazard. It is composed of an equilateral triangle surrounding an exclamation mark. The safety alert symbol shall not be used to alert persons to property-damage-only accidents. See Figure 1.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

4

A B C D E

Figure 1 – The safety alert symbol:

(A) for use with DANGER signal word, (white triangle, red exclamation mark and red background), (B) for use with WARNING signal word, (black triangle, orange exclamation mark), (C) for use with CAUTION signal word, (black triangle, yellow exclamation mark), (D) and (E) 1 for use with DANGER, WARNING or CAUTION signal words (yellow background, black border and black exclamation mark. (E) has a yellow border around the black band.)

4.10 safety sign: A visual alerting device in the form of a sign, label, decal, placard or other marking which advises the observer of the hazard(s) which can cause an accident and the level of hazard seriousness. It may also provide other directions to eliminate or reduce the hazard and may advise of the probable consequences of not avoiding the hazard.

4.10.1 environmental safety sign: Sign or placard in a work or public area that provides safety information about the immediate environment.

4.10.2 product safety sign: Sign, label, or decal affixed to a product that provides hazard and safety information about that product.

4.11 safety signs and signal words, types of : The seven types of safety signs are DANGER, WARNING, CAUTION, NOTICE, safety instructions and safety equipment location, fire safety, and directional arrows. The first five types of safety signs use a signal word or words to designate a level of hazard seriousness. No signal words are used for fire safety or directional arrow signs. Signal words are the word or words that designate a degree or level of safety alerting. Specific signal words are defined here and the definition repeated where they appear in subsequent sections (see Section 5 inclusive). The signal word or words shall always be located in a distinctive panel located in the uppermost portion of the safety sign.

4.11.1 DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations.

4.11.2 WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

4.11.3 CAUTION: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used without the safety alert symbol as an alternative to “NOTICE”.

1 D and E are provided to allow for consistency with certain ISO standards, such as ISO 3864-1 and ISO 3864-2.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

5

4.11.4 NOTICE: “NOTICE” is the preferred signal word to address practices not related to personal injury. The safety alert symbol shall not be used with this signal word. As an alternative to “NOTICE”, the word “CAUTION” without the safety alert symbol may be used to indicate a message not related to personal injury.2 4.11.5 signs for safety instructions or safety equipment location: Signs used to indicate general instructions relative to safe work practices or indicate the location of safety equipment.

4.11.6 fire safety: Signs used to indicate the location of emergency fire fighting equipment. (Note: These signs indicate the location of, but not the direction to, equipment, etc.)

4.11.7 directional arrow signs: Signs used to indicate the direction to emergency equipment, safety equipment, and other locations important to safety.

4.12 surround/surround shape: A geometric configuration around the symbol which can convey additional safety information.

4.13 safety symbol: A graphic representation intended to convey a message without the use of words. It may represent a hazard, hazardous situation, precaution to avoid a hazard, the result of not avoiding the hazard, or any combination of these messages. (See ANSI Z535.3-2007 Criteria for Safety Symbols.)

5 Safety sign colors and formats

5.1 DANGER signs

5.1.1 Signal word panel. Danger signs shall have the signal word “DANGER” in white letters on a rectangular safety red background placed at the top of the sign. The safety alert symbol shall precede the signal word. The base of the symbol shall be on the same horizontal line as the base of the letters of the signal word. The height of the safety alert symbol shall be equal to or exceed the signal word letter height. See Figure 2.

Figure 2 – Format for the DANGER signal word panel - white letters on safety red background

5.1.2 Message panel. The message shall be in black or red letters on a white background, or white letters on a black background.

2 It is the intention of the ANSI Z535 committee to eliminate the alternative of using the signal word CAUTION without the safety alert symbol to indicate a hazardous situation not related to personal injury in the 2011 version of this standard. This will assist in making more of a differentiation between safety messages indicating personal injury and messages not related to personal injury.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

6

5.1.3 Safety symbol panel. The safety symbol panel, if used, shall be a square or rectangle with a black, safety red, or black and safety red symbol on a white background.

5.2 WARNING signs

5.2.1 Signal word panel. Warning signs should have the signal word “WARNING” in black letters on a rectangular orange background placed at the top of the sign. The safety alert symbol shall precede the signal word. The base of the symbol shall be on the same horizontal line as the base of the letters of the signal word. The height of the safety alert symbol shall be equal to or exceed the signal word letter height. See Figure 3.

Figure 3 – Format for the WARNING signal word panel—black letters on safety orange background

5.2.2 Message panel. The message shall be in black letters on a white background or white letters on a black background.

5.2.3 Safety symbol panel. The safety symbol panel, if used, shall be a square or rectangle with a black symbol on a white background.

5.3 CAUTION signs

5.3.1 Signal word panel—personal injury. Caution signs shall have the signal word “CAUTION” in black letters on a rectangular yellow background placed at the top of the sign. The safety alert symbol shall precede the signal word if the hazard is a potential personal injury hazard. The base of the symbol shall be on the same horizontal line as the base of the letters of the signal word. The height of the safety alert symbol shall be equal to or exceed the signal word letter height. See Figure 4.

Figure 4 – Format for the personal injury CAUTION signal word panel—black letters on safety yellow background

5.3.2 Alternate Signal word panel for practices not related to personal injury. The safety alert symbol shall be omitted on CAUTION signs used as an alternate to NOTICE to address practices not related to personal injury. These signs shall have the signal word CAUTION in black letters on a rectangular safety yellow background placed near the top of the sign. See Figure 5.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

7

Figure 5 – Format for the CAUTION signal word panel not related to personal injury when used as an alternate to NOTICE—black letters on safety yellow background.

5.3.3 Message panel. The message shall be in black letters on a white background or white letters on a black background.

5.3.4 Safety symbol panel. The safety symbol panel, if used, shall be a square or rectangle with a black symbol on a white background.

5.4 NOTICE signs

5.4.1 Signal word panel. These signs shall have the signal word “NOTICE” in white italic letters on a safety blue background on a rectangular field, and this distinctive panel shall be located in the uppermost portion of the visual alerting device. No other signal word or symbol shall be used within this distinctive shape and color arrangement.

Figure 6 – Format for the NOTICE signal word panel—white italic letters on safety blue

background.

5.4.2 Message panel. The message shall be in safety blue or black letters on a white background.

5.4.3 Safety symbol panel. The safety symbol panel, if used, shall be a square or rectangle with a safety blue or black symbol on a white background.

5.5 Signs for safety instruction or safety equipment location

5.5.1 Signs containing safety instructions or procedures should use the signal words SAFETY INSTRUCTIONS or SAFETY PROCEDURES. More definitive signal words, such as SAFE SHUTDOWN PROCEDURE, are encouraged, where practical. Signs indicating the location of safety equipment (except fire fighting equipment) would use definitive signal words, such as EYEWASH. Where multiple safety items are at the same location, SAFETY EQUIPMENT may be used as the signal words. The signal word or words shall be in white letters on a safety green background on a rectangular field, and this distinctive panel shall appear in the uppermost portion



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

8

of this sign. Signal words that are not in accordance with the definition given in 4.11 shall not be used and these include DANGER, WARNING, and CAUTION. See Figure 7.

Figure 7 – Formats of signal word panels used for safety instruction and safety equipment location signs—white letters on safety green background.

5.5.2 Message panel. The message shall be in safety green or black letters on a white background.

5.5.3 Symbol panel. The symbol panel, if used, shall be a square or rectangle with a safety green or black symbol on a white background.

5.6 Fire safety signs

5.6.1 Signal word panel. These fire safety signs do not have a signal word.

5.6.2 Message Panels. The message panel shall be in safety red letters on a white background in either a square or rectangular field.

5.6.3 Safety symbol panel. The safety symbol panel, if used, shall be safety red on white or white on safety red. See Figure 8.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

9

Figure 8 – Example of fire extinguisher location safety sign (from ISO 7010-2003).

5.7 Directional arrow signs

5.7.1 Directional arrow sign panels. This directional arrow symbol shall be in white on a black or colored background on a rectangular field, and this distinctive symbol shall appear in the uppermost portion of the visual alerting device when used by itself or in conjunction with general safety or fire safety signs. When these directional arrows are used in conjunction with DANGER, WARNING, CAUTION, or NOTICE signs, the arrows shall be in a lower sign panel. The color of the arrows shall be in the same color arrangement as the message or symbol as described in the definition section 5.0 inclusive. Directional arrows shall be designed as illustrated in Figure 9.

5.7.2 Illustration. This distinctive shape shall be designed as illustrated below:

Figure 9 – Directional arrow (indicating movement to the right—from ISO 7010-2003).

5.8 Special signs

5.8.1 Definitions. These signs have been developed for special uses and have been separated from the other categories of hazard alerting devices by special layout. These visual alerting devices are covered by other standards as listed in the Reference section.

5.9 Sign classification selection

5.9.1 It is not the intent of this standard to define precisely levels of hazard or where the various hazard level signs are to be used.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

10

5.9.2 When no federal, state, or local government code, regulation, standard, or guideline specifically requires the use of a particular hazard alerting signal word, it shall be up to those responsible to select the appropriate hazard classification. Each situation requiring the use of a hazard alerting device should be reviewed with regard to the definitions given in section 4 inclusive and 5 inclusive.

5.9.3 Safety alert symbol

The solid triangle portion shall be the same color as the signal word lettering, and the exclamation mark portion shall be the same color as the signal word panel background. Or as an alternative, the safety alert symbol may consist of a black triangle band and black exclamation mark on a safety yellow triangle. (See Figure 1).

6 Sign design/layout

6.1 Three panel signs. Three panel signs shall be as illustrated as in Figure 10, 11, 13, 17, 18, or 19.

6.2 Two-panel signs. Two panel signs shall be as illustrated as in Figure 12, 14, 15, or 16.

6.3 Application of sign formats by hazard classification: Table 1 and Figures 10 – 21 shall be used to determine which sign panel formats may be used with which sign classification.

Table 1— Application of sign panel formats* Sign Classification Permitted Prohibited or Not

Used DANGER Figures 10 – 20 Figures 21 and 22 WARNING Figures 10 – 20 Figures 21 and 22 CAUTION Figures 10 – 20 Figures 21 and 22 NOTICE Figures 10 – 20 Figures 21 and 22

SAFETY INSTRUCTIONS or SAFETY EQUIPMENT LOCATION

Figures 10 – 20 Figures 21 and 22

FIRE SAFETY Figures 21 and 22 Figures 10-20 DIRECTIONAL Figures 21 and 22 Figures 10-20

7 Sign color specifications

The color of sign finishes shall conform to the ANSI Z535.1-2006 Safety Color Code.

8 Safety symbols

8.1 General

8.1.1 Safety symbols are pictorials, pictographs, or other graphic representations chosen to clearly convey a specific safety alerting message.

8.1.2 The conveyed message of a symbol is to describe the type of hazard, potential consequences of the hazard, or evasive/avoidance actions to be taken. When used, the symbol must be compatible with the word message(s).



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

11

8.2 Safety symbol use

Safety symbols may be used to clarify, supplement or substitute for a portion or all of a word message found in the message panel. A symbol may only be used to substitute for a portion or all of a word message if it has been demonstrated to be satisfactorily comprehended (e.g., Annex B of ANSI Z535.3) or there is a means (e.g., instructions, training materials, manuals, etc.) to inform people of the symbol’s meaning.

9 Letter style and size

Note—For additional reference on letter style and size, see Annex B).

9.1 Letter style

9.1.1 Signal words shall be sans serif letters in upper case only.

9.1.2 Message panel lettering should be a combination of upper and lower case sans serif letters. Upper case only lettering may be used for short messages or emphasis of individual words.

9.1.3 Examples of acceptable lettering styles include: Arial, Arial Bold, Folio Medium, Franklin Gothic, Helvetica, Helvetica Bold, Meta Bold, News Gothic Bold, Poster Gothic, and Universe.

9.2 Letter size

9.2.1 Legibility of text is influenced by letter height, the ratio of letter height to width (stroke width), and spacing between letters, words, and lines. Annex B provides guidance on these and other factors that affect text legibility.

9.2.2 The overall size of the lettering shall be determined by the distance from which the sign can be safely and easily read. The message should be as concise as practical. Letters shall be adequately spaced and not crowded.

9.2.3 Minimum letter height shall be one unit in height for every 150 units of safe viewing distance from the hazard alerting device for signal words and one unit in height for every 300 units viewing distance for the majority of other words contained on the word message panel (see Reference 15). The safe viewing distance must be determined for each specific case where a safety sign is needed. The message panel text shall meet the legibility criteria at the determined safe viewing distance.

10 Sign finish

10.1 Sign finish shall be of durable materials with colors in accordance with ANSI Z535.1-2006 Safety Color Code.

11 Sign placement

11.1 Signs shall be so placed to alert and inform the viewer in sufficient time to take appropriate evasive actions to avoid the potential harm from the hazard.

11.2 Safety signs shall be so placed that they are legible, non-distracting, and not hazardous in themselves.

11.3 Safety signs shall not be located in areas where they may be removed by the motion of the hazardous device, or rendered ineffective by situational conditions of the hazard. These alerting devices shall not be blocked by moveable panels such as doors, windows, racks, gates, etc.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

12

12 Illumination

12.1 All hazard alerting devices shall be displayed with illumination or retro-reflectorization as needed for adequate legibility under normal operating conditions. Where illumination is inadequate or colors not recognizable, use supplemental illumination3 (see Reference 14).

Consideration should be given for situations other than normal operating conditions, such as emergency conditions, visibility, power failure, etc. Where illumination may be interrupted, the sign should be equipped with emergency lighting or retro-reflective materials, or both.

13. Normative References

1. American National Standards Institute (ANSI). Safety Color Code. ANSI Z535.1-2006.

2. American National Standards Institute (ANSI). Criteria for Safety Symbols. ANSI Z535.3-2007.

3 Supplemental illumination includes portable illumination such as flashlights.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

13

The symbol panel may be located on either side of the message panel.

NOTICE

Color Descriptions:

Signal Word Panel:DANGER: White Lettering/Red Background

WARNING: Black Lettering/Orange Background

CAUTION: Black Lettering/Yellow Background

NOTICE: White Italic Lettering/Blue Background

SAFETY INSTRUCTIONS orSAFETY EQUIPMENT LOCATION(not shown): White Lettering/Green Background

Safety Alert Symbol:See Figure 1 for options

Word Message:Black Lettering on White Background(or)White Lettering onBlack Background

Figure 10 – Examples of Signal Word Panels Using Various Safety Alert Symbols— Three-Panel Sign Horizontal Format.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

14

Vertical formats can be extendedto provide additional spacefor the word message.

Figure 11 – Three-Panel Sign—Vertical Format

Figure 12 – Two-Panel Sign—Vertical Format



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

15

Horizontal formats can be extended to provide additional spacefor the word message.Keep the safety alert symboland signal word next to each other and centeredin the signal word panel.

Figure 13 – Three-Panel Sign—Horizontal Format

Figure 14 – Two-Panel Sign—Horizontal Format

Figure 15 – Two-Panel Sign—Shortened Signal Word Panel Format

Figure 16 – Two-Panel Sign—Side-By-Side Format



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

16

Figure 17 – Three-Panel Sign—Horizontal Format with Symbol Panel on Right

Figure 18 – Three-Panel Sign—Horizontal Format with Message Panel and Symbol Panel Separated by Line

Figure 19 – Three-Panel Sign—Horizontal Format with Message Panel and Symbol Panel Separated by White Space

Figure 20 – Two-Panel Sign—Signal Word Panel and Symbol Panel



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

17

NOTE—In all of the above examples of Figures 11 – 20, any of the signal word and safety alert symbol combinations can be used. The examples below in Figures 21 and 22 are restricted to fire safety and directional signs and labels.

Figure 21 – Two-Panel Sign—Vertical Format with Message Above Symbol Panel

Figure 22 – Two-Panel Sign—Vertical Format with Message Below Symbol Panel



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

18

Annex A (informative)

Guidelines for Increasing Recognition of Safety Sign Components

A1 Scope

It is important that the meaning of a safety sign is clearly understood by those who may come in contact with the hazard. To increase the understanding of a safety sign’s components, the ANSI Z535 committee encourages safety sign manufacturers and owners of facilities to publish and exhibit the following information on safety posters, safety bulletins or the like. Doing so will assist in the objective of achieving a national uniform system for the recognition of personal injury hazards and accident prevention.

A1.1 The safety alert symbol

Explain the meaning of the safety alert symbol. Then use this symbol whenever a safety-related message is written that warns of a personal injury hazard. In literature that makes note of personal injury hazards, the safety alert symbol can be used alone or in combination with the proper signal word to call attention to the hazard information. The following artwork may be used for this purpose.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

A1.2 The signal words

Explain the meaning of the different signal words as defined by the ANSI Z535.2 standard. Such training is necessary to increase understanding of the meaning of signal words. The following artwork may be used for this purpose.

NOTE—The use of the appropriate color for each signal word panel is desirable. See ANSI Z535.1.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury

NOTICE is used to address practices not related to personal injury



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

19

CAUTION without the safety alert symbol is used to address practices not related to personal injury.1

Safety instruction or safety equipment location signs indicate general instructions relative to safe work practices or indicate the location of safety equipment.

A1.3 Safety symbols

Explain the meaning of the safety symbols used on your safety signs. This enables viewers to better understand the meaning of the graphics and makes future recognition of the safety symbols more instantaneous. See ANSI Z535.3 Criteria for Safety Symbols for more information about safety symbol selection, design and testing.

1 It is the intention of the ANSI Z535 committee to eliminate the alternative of using the signal word CAUTION without the safety alert symbol to indicate a hazardous situation not related to personal injury in the 2011 version of this standard. This will assist in making more of a differentiation between safety messages indicating personal injury and messages not related to personal injury.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

20

Annex B (informative)

Principles and Guidelines for the Design of Environmental and Facility Safety Signs

B1 Scope

Good consistent visual design helps to effectively communicate hazard information. The purpose of this annex is to provide the designer with information on widely recognized principles that can aid in the development of effective safety signs. 1

B2 Signal word panel arrangement

For those signal words that require the use of the safety alert symbol (i.e. DANGER, WARNING, and CAUTION), the safety alert symbol and signal word should be positioned close together and centered in the signal word panel. See Figures B1 and B2. For those signal words that do not require the safety alert symbol (i.e. NOTICE, SAFETY INSTRUCTIONS, CAUTION, EYEWASH, etc.), the signal word should be positioned in the center of the signal word panel. For property-damage-only safety signs, the signal word CAUTION is used without the safety alert symbol (see Annex A).

Figure B1 – Examples of Correct Signal Word and Safety Alert Symbol Placement Figure B2 – Examples of Incorrect Signal Word

and Safety Alert Symbol Placement

B3 Developing the Word Message

B3.1 The content of the word message The word message on a safety sign typically communicates information to an observer on the type of hazard, the consequence of not avoiding the hazard and how to avoid the hazard. Many factors must be considered when determining whether to omit consequence, avoidance or type of hazard information in the word message. Factors to consider include whether the message can be inferred from a symbol, other text messages, user training or the context in which the safety sign is used.

B3.2 Ordering the content of the word message The order in which the content appears in the message panel is flexible. Factors to consider when determining the order of a word message’s content include the target audience’s degree of prior knowledge of the hazard and the reaction time required to avoid the hazard.

1 Note – Every safety sign must be considered on its own terms. Limitations on space or other unique conditions may justify variance from these principles. Examples of word messages are provided to illustrate how principles related to grammatical structure, writing style and print layout can enhance the safety sign. These examples are not intended to prescribe standardized word messages for the hazards mentioned in the examples.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

21

The information required on a safety sign should be arranged to provide the most important information first. Where reaction time is an issue, the action statement will be the most important portion of the word message and should be placed first. In other cases, the hazard description statement will be the most important information to communicate first. The statement concerning the consequences of interaction with the hazard is generally best understood when placed after the hazard description statement, or used integrally with the hazard description statement. As a general rule, the hazard message should come first when there are many feasible action/avoidance alternatives. However, action/avoidance messages should come first when there are few avoidance alternatives.

Figure B3 illustrates a word message that explains the type of hazard and consequences of interaction with the hazard before it describes the hazard avoidance information. Placing the information in this order would be appropriate if it is found that the audience needs to know what the hazard is before they would follow the avoidance information presented on the sign. This format assumes that there is time to read the entire word message and still avoid the hazard.

Figure B4 illustrates a word message that places the hazard avoidance information first. Ordering the word message in this way would be appropriate if a person needs to immediately follow the avoidance information in order to prevent interaction with the hazard.

Type of Hazard and Consequence Statement

Avoidance Statements

Moving parts can crush and cut

Keep out during operation

Lockout power before entering

Keep Out

Hazardous voltage inside

Can shock, burn or cause death

Avoidance Statement

Type of Hazard Statement

Consequence Statement

Figure B3 – Word Message With Hazard Description First

Figure B4 – Word Message With Hazard Avoidance Message First

B3.3 Formatting the word message

There are many issues that must be considered when developing a word message; from sentence structure to typesetting specifications. The length of the word message depends on the amount of information that needs to be communicated to a person to allow them to understand and avoid the hazard. Once this information is determined, it should be written and formatted in a manner that is concise and easily understood. The following are several principles that can be applied to the word message to achieve this objective.

B3.3.1 Use headline style

Write in a “headline style.” Compare the sample word messages shown in Figures B5 and B6. The “headline style” example of Figure B5 eliminates nonessential words and omits pronouns (“this,” “that,” “they”) articles (“a,” “the,” “an”) and forms of the verb “to be” (“is,” “are,” “were”). Avoid hyphenation when at all possible.

Hazardous voltage. Keep out! Keep access door locked.

Hazardous voltage is very danger- ous and should be avoided at all times. Keep the access door closed at all times and do not enter this area.

Figure B5 –Headline Style Message Figure B6 – Non-Headline Style

Message



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

22

B3.3.2 Use succinct statements

Safety signs are intended to communicate appropriate information to the viewer fast enough to allow the viewer to comprehend the information and take the necessary actions to avoid the hazard. Faster reaction times are promoted by using succinct statements.

B3.3.2.1 Action statement

The action statement gives the viewer instructions on how to avoid the hazard. The statement should be simple, direct, and applicable to the hazard. Figure B7 contains examples of action statements.

Keep Out! Wear hard hats No smoking

Keep away Call before you dig Do not operate!

Figure B7 – Examples of Action Statements

B3.3.2.2 Hazard description statement

The hazard description statement identifies the specific hazard in clear, simple language. Where the desired action and the consequence of not avoiding the hazard are obvious from the hazard description statement (such as “Slippery when wet”), the action and consequence statements may be omitted. Figure B8 contains examples of concise hazard description statements:

Hazardous voltage inside Confined space Biological hazard

Laser radiation Hot pipes above Buried fiber optic cable

Figure B8 – Examples of Concise Hazard Description Statements B3.3.2.3 Consequence statement

The consequence statement tells the viewer in clear, simple language what will happen if the warning is ignored. Figure B9 contains examples of consequence statements:

Will burn Can cause serious burns or death Can irritate skin

Can cause infertility Will disrupt electrical service to critical equipment

Exposure can cause nausea, dizziness, and a headache

Figure B9 – Examples of Consequence Statements

B3.3.2.4 Emergency information

Where it is important for viewers or accident responders to know the ownership of the affected facilities, a telephone number or other useful information should be placed after the Action, Hazard Description and Consequence statements.

B3.3.3 Use active voice

Write sentences in the active voice, rather than the passive voice. This means placing the subject of the sentence first, the action (verb) next, and the object (noun) last. Often the subject “you” or “your” can be inferred from the sentence and is unnecessary. Figure B10 contrasts active voice with passive voice messages.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

23

Active Voice Messages Passive Voice Messages

Keep hands away from rotating blade.

Lock out power before servicing equipment.

Replace guards immediately after repair or adjustment.

Your hands must be kept away from rotating blade.

Power must be locked out before servicing equipment.

After repair of adjustment, immediately replace guards.

Figure B10 – Examples of Active Voice vs. Passive Voice Messages

B3.3.4 Avoid prepositional phrases

Avoid the use of prepositional phrases. Prepositional phrases can often be eliminated or replaced with one word. Figure B11 contrasts messages with and without prepositional phrases.

Messages Without Prepositional Phrases Messages With Prepositional Phrases

Disconnect power before servicing equipment.

Turn off power if jam occurs

Disconnect power in order to service equipment.

Turn off power in the event a jam occurs.

Figure B11 – Examples of Concise Prepositional Phrases

B3.3.5 Emphasizing desired action or other message

Where room is available and it is desired to emphasize the desired action or other message, key words may be shown in larger letters, in all capital letters, in bolder letters, in a different type face, with an exclamation mark, or with a combination thereof. Figure B12 contains examples of ways to emphasize portions of a word message.

Hazardous voltage inside.

Keep Out!

Keep access door locked.


KEEP OUT!

Keep access door locked.


KEEP OUT! Keep access door locked.

Example A Example B Example C

Figure B12 – Examples of Ways to Emphasize Portions of a Word Message

B3.3.6 Refer to another source

Keep only essential hazard-related information in the safety sign. If necessary, consideration can be given to referring the viewer to another source for additional safety information or for permission to proceed. Examples of such sources include safety instruction labels, Material Safety Data Sheets (MSDS), operation manuals, service manuals, operating procedures and safety bulletins.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

24

B3.3.7 Separation of word message content

To enhance readability, arrangements of the word message in an outline format should be considered, as in Figure B13. The addition of bullets may also be considered to help separate portions of the word message, as in Figure B14. The use of continuous format, as in Figure B15, is sometimes necessary for product safety labels and temporary tags (see ANSI Z535.4 and Z535.5), but is rarely necessary or appropriate for environmental and facility safety signs.

Moving parts can crush and cut.

Keep out during operation.

Lockout power before entering.


• Keep out during operation.

• Lockout power before entering.

Moving parts can crush and cut. Keep out during operation. Lockout power before entering.

Figure B13 –Outline Format

Figure B14 –

Outline With Bullet Format

Figure B15 –

Continuous Format

B3.3.8 Text justification Left aligned “ragged right” text should be used for all but one-line text messages (which can be either left aligned or centered). See Figure B16. Left alignment aids in readability (compared to centered text; see Figure B17) by creating a vertical line that the eye naturally locates when searching for the next line of text. Justified text should be avoided because the added space between words makes it more difficult to read. See Figure B18.










Figure B16 – Left Aligned

Ragged Right Text

Figure B17 –Centered Text

Figure B18 –Justified Text

B3.3.9 Upper and lower case letters The preferred format for text is the use of mixed upper and lower case where only the first letter of the first word in a sentence is capitalized. See Figure B19. The use of all upper case letters for the word message is discouraged because it is more difficult to read quickly than lower case type. See Figure B20. On occasion, a single word or phrase may be set in upper case letters to provide emphasis. See Figure B21.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

25




MOVING PARTS CAN CRUSH AND CUT.

KEEP OUT DURING OPERATION.

LOCKOUT POWER BEFORE ENTERING.

Moving parts can CRUSH and CUT

KEEP OUT during operation

LOCKOUT POWER before entering

Figure B19 –Mixed Case

Lettering

Figure B20 – All Upper Case

Figure B21 – Selective Use of

Upper Case

B3.3.10 Choice of type style Sans serif typestyles are preferred. The important specification to look for when choosing a typestyle is the stroke “width-to-height” ratio. This ratio refers to the width of the letter and the strokes used to create the letter. For black type on a white background the stroke width-to-height ratio should be 1:6 –1:8. For white type on a black background the stroke width-to-height ratio should be 1:8 –1:10 (See Annex E, Informative References, Number 15).

B3.3.11 Choice of type spacing

The correct spacing between lines of text, between words, and between letters helps to make a word message easier to read. The amount of space between lines of text is called leading. Lines of text should be separated by leading that is approximately 120% of the type point size (e.g. 10 point type should have 12 point leading, 14 point type should have 16.8 point leading, etc.). Additional leading can be added to separate portions of a word message, as shown in the outline format illustrated in B3.3.7. The space between words and between letters is called tracking. For purposes of legibility, it is important to use proper word and letter spacing when typesetting the word message. See Figure B22.

This is an example of a word message with proper leading and word/letter spacing.

Th is i s an examp le o f a w o r d m e s s a g e w i t h t o o m u c h l e a d i n g a n d t o o m u c h w ord / l e t t e r spac ing .

This is an example of a word message with not enough leading and not enough word/letter spacing.

Example A – Proper leading and spacing

Example B – Too much leading and spacing

Example C – Not enough leading

and spacing

Figure B22 – Examples of Correct and Incorrect Type Spacing

B3.3.12 Choice of type color

The word message’s type can be black on a white background or white on a black background. This choice should be based on which is more legible. Legibility is dependent on more than type color. Factors such as type size, amount of text, reading distance, contrast with the product surface, and lighting conditions must all be considered. See Figure B23.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

26

Black type on a white background







White type on a black background

Figure B23 – Examples of Type Color Choice

B3.3.13 Letter size

Legibility of the word message at the minimum safe viewing distance2 determines the proper letter size for the word messages. The letter size/safe viewing distance guidelines in Table B1 define the type size required to achieve legibility at the given viewing distance. The height of the capital letter “H” identifies the type’s letter size. Note that the type sizes shown in column two and column three of Table B1 indicate the minimum word message letter size for favorable light conditions and the recommended letter size for unfavorable reading conditions, respectively. Letter size may need to be larger than the values in column two for various reasons, including the following: • to obtain conspicuousness from other information displayed in the area, • to facilitate legibility under low light, or other unfavorable viewing conditions, • to warn persons at distances greater than the minimum safe viewing distance, • to convey special emphasis for portions of the message, and • to facilitate legibility for populations who have difficulty reading small text (e.g., senior citizens). A formatted sign with the selected letter size word messages should be visually examined in the environment expected for actual use (lighting, background, angle, etc.) and tested for legibility in that environment by persons representative of the expected viewers. It is advisable to test different letter sizes to determine the optimum size for legibility at the desired viewing distance.

B3.3.14 Minimum letter height calculations

Type size is defined in “points,” a term that was used to describe the space required for lead type characters. Point sizes measure from the top of the capital letters to the bottom of the lower case letters with descenders (e.g. the bottom of the letter “g” or “j”, etc.). One point equals 0.01384 inches, or approximately 1/72 of an inch. Although type faces vary slightly, a practical guide for defining type size is based on using the capital letter “H” for measurement purposes. Since the character “H” has no descender, it is possible to use a conversion factor of 0.01 inches = 1 point of type size. Thus, 12 point type yields a capital “H” approximately 0.12 inches high. For metric purposes, use a conversion factor of 3.9 points =1 mm of height for a capital “H.”

2 The minimum safe viewing distance refers to the closest distance a person can be to the sign and still have time to follow the safety sign’s message to avoid the hazard.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

27

Table B1 – Examples of word message letter heights and minimum safe viewing distances

Minimum Safe Viewing Distance2

Minimum Height for FAVORABLE Reading Conditions

Recommended Letter Height for UNFAVORABLE Reading Conditions

(ft)

(m)

[viewing distance (ft)/25]

(in)

[viewing distance

(m)/3]

(cm)

[viewing distance (ft)/12]

(in)

[viewing distance (m)/1.43]

(cm)

<4 6 8

10 15 20 30 40 60 80

100 125 150 200

<1.2 1.8 2.4 3.0 4.6 6.1 9.1

12.2 18.3 24.4 30.5 38.1 45.7 61.0

.16*.24.32.40.60.80

1.201.602.403.204.005.006.008.00

0.4*0.60.81.01.52.03.04.16.18.1

10.212.715.220.3

.33.50.66.83

1.271.682.513.365.046.728.40

10.4912.5816.79

0.8 1.3 1.7 2.1 3.2 4.3 6.4 8.5

12.8. 17.1 21.3 26.6 32.0 42.7

*.16 inch (0.4 cm) type is the suggested minimum type size for use on environmental/facility safety signs

B3.3.15 Comprehension

The word message should be written so that it can be understood by the target audience (i.e. those who are expected to be in the vicinity of the hazard). This means choosing words that accurately describe the specific hazard and avoidance information in terms the intended audience will understand.

B4 Use of safety symbols

Well designed safety symbols can often communicate hazard information quickly and across language and literacy barriers. Although the ANSI Z535.2 standard allows word-message-only formats for safety labels, the use of safety symbols is encouraged whenever practical. See ANSI Z535.3 Criteria For Safety Symbols for additional information concerning symbol selection, design and testing.

B5 Multi-lingual formats

The selection of additional languages for safety signs is an extremely complex issue. Experts suggest that nearly 150 languages are spoken in the United States and over 23 million Americans speak a language other than English in their homes. If it is determined that additional languages are desired on a safety sign, the following formats should be considered. In all examples, the use of symbols is strongly encouraged in order to better communicate the sign’s hazard information across language barriers. White type on a black background is used in these examples only to differentiate the placement of safety symbol and word message panels.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

28

B5.1 Vertical formats

The vertical bilingual format shown in Figure B24 can be modified to include a longer word message by lengthening the word message panels.

B5.2 Horizontal formats

Figures B25 and B26 illustrate horizontal formats for bilingual safety signs. In Figure B25, the English word message and signal word may appear on either the right or left side. The text and signal word panels may be widened to accommodate longer word messages.

Language Number OneWord Message

Language Number TwoWord Message

SIGNAL WORD(Language Two)

SIGNAL WORD(Language One)

PictorialSymbolPanel

Figure B25 – Long Message, Horizontal Format

English Word Message

SIGNAL WORD(English)

SymbolPanel

Second Language Word Message

SIGNAL WORD(Second Language)

English Word Message

Second LanguageWord Message

SIGNAL WORD(English)

SIGNAL WORD(Second Language)

SymbolPanel

Figure B26 – Short Message Format

Figure B24 – Long Message, Vertical Format

B5.3 Signal word panel arrangement

The safety alert symbol and signal word should be positioned close together and centered in each signal word panel of a bilingual safety label (see B2).

B6 Multi-hazard formats

If multiple hazards exist at one location on a product or if there is only enough space for a single safety label, a multi-hazard label may need to be considered. The use of symbols in multi-hazard formats is optional but encouraged. Additional symbols can be added to these formats as needed. The signal word corresponding to the hazard with the greatest seriousness level should be used. The hazard with the greatest seriousness level should be ordered first in the word message. White type on a black background is used in these examples only to differentiate the placement of safety symbol and word message panels. The following options can be considered when designing multi-hazard signs.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

29

B6.1 Three-panel formats

Use one of the standard three-panel formats shown in Figure 13 of the ANSI Z535.2 standard and use a single symbol to communicate the most important hazard. Use the outline format to separate the various hazard word messages (see B3.3.7).

B6.2 Two-panel formats

Use the two-panel signal word/word message formats shown in Figure 14 of the ANSI Z535.2 standard. Use the outline format to separate the various hazard word messages (see B3.3.7).

B6.3 Multi-symbol formats

Use one of the multi-symbol formats shown in Figures B27 through B31. In formats B27 and B28, place the most important hazard symbol in the upper left panel so that it is “read” first and order the word message segments so they correspond to the order of the symbol (“reading” the symbols from left to right or top to bottom). If the format shown in Figure B28 is used, arrange the word message segments so they line up opposite the appropriate symbol panel.

Word message with portions separated by additional leading, lines and/or bullets.

SIGNAL WORD

SymbolPanel

SymbolPanel

SymbolPanel

Word message with portions separated by additional leading, linesand/or bullets.

SIGNAL WORD

SymbolPanel

SymbolPanel

SymbolPanel

Word message with portions separated by additional leading, lines and/or bullets.

SymbolPanel

SIGNAL WORDSymbolPanel

Figure B27 – Multiple Symbols on Top

Figure B28 – Multiple Symbols on Left

Figure B29 – Two-Symbol Alternative Format

Figures B30 and B31 illustrate the multi-hazard/multi-signal word formats. In these formats, each hazard is ordered according to its seriousness level and placed below the appropriate signal word. Additional pictorials or word messages may be located under each signal word as needed. Use the outline format to separate portions of the word message with additional leading, lines or bullets (see B3.3.7).

Figure B30 – Symbols on Left Figure B31 – Symbols on Right



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

30

Annex C (informative)

Previous Formats for Signal Word Panels

The following formats for signal word panels were used in earlier editions of this standard and were included as an alternate to the preferred panel format in the 1998 Edition. They are not included in this edition of the standard. Existing signs, in use or already manufactured that use the older format may continue to be used.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

31

Annex D (informative)

This annex is not an official part of the body of this standard.

Risk Estimation and Signal Word Selection D1 Scope Signal words are selected based on the risk that results from not following the safety message. The level of risk determines signal words, safety colors, and whether or not to use the safety alert symbol. This annex provides guidance for estimating risk and selecting signal words.

D2 Definitions D2.1 Accident: An incident that results in unintended harm.

D2.2 Harm: Death, injury or property damage.

D2.3 Hazard: A potential source of harm.

D2.4 Hazardous Situation: A condition or act that is contrary to the implicit or explicit instructions of a safety message and that exposes a person or property to increased risk of harm. The presence of the condition or performance of the act may be intentional or unintentional. However, conditions or acts that are implemented with the intention of causing harm are not considered hazardous situations within the scope of this standard.

D2.5 Incident: An unintentional and undesired event that has the potential to cause harm.

D2.6 Risk: A combination of the probability of occurrence of harm and the severity of that harm.

D3 Risk Estimation

D3.1 General

Risk estimation involves (a) considering the probability and severity of harm that can result from a hazardous situation and (b) combining these estimates to determine the risk. While quantitative risk assessment is possible in certain limited circumstances, only qualitative risk estimates are possible in most cases. For the purpose of safety messages classification (i.e., assigning a signal word and safety color, and determining whether the safety alert symbol is appropriate), qualitative risk estimation is commonplace and generally appropriate.

There are numerous methods for estimating the risk posed by a hazardous situation. This section outlines one method that is specifically designed to assist in assigning signal words according to the definitions in this standard. For information about other risk estimation methods or models, see the references at the end of this annex.

D3.2 Hazardous situation

Safety messages provide instructions, explicit or implicit, regarding how to avoid hazardous situations. In order to select the appropriate signal word, risk must be estimated for the particular hazardous situation or situations.

Note that, for the purposes of signal word selection, it does not matter why a safety message might not be followed (e.g., failure to read the message, conscious decision to ignore the message); the hazardous situation associated with a message is the same, regardless of why the message is not followed.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

32

When a safety message addresses more than one hazardous situation, the risk associated with each hazardous situation should be estimated. In these cases, the signal word corresponding to the greatest risk level is used.

D3.3 Model of Events Resulting from a Hazardous Situation

Figure D1 shows the possible results of a hazardous situation.

Figure D1 – Model of the possible results of a hazardous situation

The hazardous situation (i.e., the result of not following a safety message) either results in an accident (i.e., harm occurs) or in no accident (i.e., either no incident occurs, or the incident does not result in harm). If an accident occurs, it results in harm. The harm can be classified by severity, from property damage to death or serious injury.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

33

D3.4 Severity

D3.4.1 Classification of severity of harm

As shown in the model above, there are three classifications for severity of harm that are used in selecting signal words:

D3.4.1.1 Death or serious injury: Injury to humans that is more severe than minor or moderate injury. Harm classified as death or serious injury may also include property damage, or moderate or minor injuries that occur as a result of the same event.

Serious injuries typically have one or more of the following characteristics

• results in permanent loss of function or significant disfigurement

• requires substantial and prolonged medical treatment

• involves long periods of disability

• involves considerable pain and suffering over long periods of time

Examples of serious injuries include amputations, severe burns, and loss or impairment of vision or hearing.

D3.4.1.2 Moderate or minor injury: Injury to humans, not including death or serious injury. Harm classified as moderate or minor injury may also include property damage that occurs as a result of the same event.

Minor or moderate injuries do not typically result in permanent disability or significant disfigurement or pain. Examples of minor or moderate injuries include cuts, scratches, and irritation.

D3.4.1.3 Property damage: Damage to property that does not include injury to humans.

D3.4.2 Hazardous situations resulting in multiple harms

When harm resulting from an event includes results falling into more than one of the severity classifications, the most severe classification should be used. For example, an event that results in both minor injury and property damage is classified as “minor or moderate injury”. Similarly, an event that results in both minor injury to one body part and serious injury to another should be classified as “serious injury or death”.

D3.4.3 Worst Credible Severity of Harm

A hazardous situation can result in a variety of outcomes, each with varying likelihood. When selecting a signal word, it is necessary to determine the worst credible harm that can result from a hazardous situation. Only outcomes that are credible possibilities should be considered.

Once the worst credible harm has been identified, it should be classified by severity (i.e., property damage only, minor or moderate injury, or death or serious injury). This category is the worst credible severity of harm for a particular hazardous situation.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

34

D3.5 Probability

Risk depends on the probability of harm. For the purpose of signal word selection, probability of harm includes the probability of an accident and the probability of the worst credible severity of harm occurring if there is an accident.

The probability of the hazardous situation occurring (i.e., the probability of the safety message not being followed) should not be included in an estimate of risk for the purpose of signal word selection.

D3.5.1 Probability of Accident

The probability of an accident if a hazardous situation exists (i.e., if the safety message is not followed) should be estimated. The probability of an accident includes the probability of accidents that result in any severity of harm.

Circumstances in which a hazardous situation does not result in an incident, or in which it results in an incident that does not cause harm, are not accidents.

D3.5.2 Probability of Worst Credible Severity of Harm

The probability of the worst credible severity of harm occurring if an accident occurs should be estimated. To estimate the probability of the worst credible severity of harm, it is necessary to include not only the likelihood of the worst credible harm, but also the likelihood of all other outcomes that fall within the worst credible severity of harm category (e.g., if the worst credible harm is death, then include all outcomes that are in the category serious injury or death).

D3.5.3 Estimating Probability

For the purposes of assigning signal words, probability need not be determined quantitatively, or with great precision. Signal words are assigned based on estimates of probability using two qualitative categories:

D3.5.3.1 Will: Indicates an event that is expected to happen with near certainty.

D3.5.3.2 Could: Indicates an event that is possible but not nearly certain.

D4 Signal word selection A signal word is selected according to the risk of harm presented by the hazardous situation that the safety message addresses. That is, signal word selection is based on the risk posed if the safety message is not followed.

The risk is determined based on

• worst credible severity of harm if an accident occurs

• probability of an accident if the hazardous situation occurs (i.e., if the safety message is not followed)

• probability of the worst credible severity of harm occurring



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

35

D4.1 Signal Word Selection Matrices

The following matrices show the signal words, colors, and presence or absence of a safety alert symbol that are assigned for each combination of accident probability, worst credible harm, and probability of worst credible harm.

If Worst Credible Severity of Harm is Death or Serious Injury

Probability of Accident if

Hazardous Situation is not Avoided Will Could

Will

Probability of Death or Serious Injury if Accident Occurs

Could

If Worst Credible Severity of Harm is Moderate or Minor Injury

For all probabilities:

If Worst Credible Severity of Harm is Property Damage

For all probabilities: Preferred:

NOTICE

Alternate:



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

36

D4.2 Signal Word Selection Process

The signal word selection process is summarized in Figure D2.

Figure D2 – Signal word selection process



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

37

D5 Informative References The following publications provide information about risk estimation and assessment:

1. American National Standards Institute (ANSI). Risk Assessment and Risk Reduction—A Guide to Estimate, Evaluate and Reduce Risks Associated with Machine Tools, ANSI B11.TR3-2000.

2. American National Standards Institute (ANSI) / Robotic Industries Association (RIA). American National Standard for Industrial Robots and Robot Systems—Safety Requirements, ANSI/RIA R15.06-1999.

3. American National Standards Institute (ANSI) / Association for the Advancement of Medical Instrumentation (AAMI) / International Organization for Standardization (ISO). Medical devices—Application of risk management to medical devices, ANSI/AAMI/ISO 14971:2000.

4. American National Standards Institute (ANSI) / Association for the Advancement of Medical Instrumentation (AAMI) / International Organization for Standardization (ISO). Medical devices—Application of risk management to medical devices—Annex H – Rationale for requirements—Amendment 1, ANSI/AAMI/ISO 14971:2000/A1:2003.

5. American National Standards Institute (ANSI) / Packaging Machinery Manufacturing Institute (PMMI). Safety Requirements for Construction, Care, and Use for Packaging Machinery and Packaging-Related Converting Machinery, ANSI/PMMI B155.1-2000.

6. British Standards. Safety of Machinery—Principals for Risk Assessment. BS EN 1050-1997.

7. Canadian Standards (CAN) / Canadian Standards Association (CSA). Risk Management: Guideline for Decision Makers, CAN/CSA -Q850-97.

8. International Organization for Standardization (ISO). Safety of Machinery—Principals for Risk Assessment, ISO 14121-1999.

9. U.S. Department of Defense. Department of Defense Standard Practice for System Safety, MIL-STD-882D, 1 – February 2000.

10. Semiconductor Equipment and Materials Institute (SEMI). Safety Guideline for Risk Assessment, SEMI S10 1103.



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

38

Annex E (informative)

This annex is not an official part of the body of this standard.

Informative References

1. American National Standards Institute (ANSI). Product Safety Signs and Labels. ANSI Z535.4-2007.

2. American National Standards Institute (ANSI). Safety Tags and Barricade Tapes (for Temporary Hazards). ANSI Z535.5-2007.

3. American National Standards Institute (ANSI). Product Safety Information in Product Manuals, Instructions, and Other Collateral Materials. ANSI Z535.6-2006.

4. American National Standards Institute (ANSI). Radio Frequency Radiation Hazard Warnings Symbol. ANSI C95.2-1982 (R1988).

5. American National Standards Institute (ANSI). Radiation Symbol. ANSI N2.1-1989.

6. Highway Transportation: American National Standard Manual on Uniform Traffic Control Devices for Streets and Highways. Millennium Edition http://mutcd.fhwa.dot.gov/

7. National Fire Protection Association. ANSI/NFPA 70 (2005), National Electrical Code.

8. National Fire Protection Association. Symbols for Fire Fighting. NFPA 178-1986.

9. Society of Automotive Engineers (SAE). Slow Moving Vehicle Identification Symbol – ANSI/SAE S276.2. Warrendale, PA: SAE, June 1968.

10. International Organization for Standardization (ISO) 3864. Safety Signs and Colors, ISO: Geneva, Switzerland, 1984-03-01.

11. American National Standards Institute for Hazardous Industrial Chemicals—Precautionary Labeling. ANSI Z129.1-2000.

12. Smith, S.L. Letter Size and Legibility. Human Factors, 1979, 21, 661 – 670.

13. Collins, B.L., Kuo, B.Y., Mayerson, S.E., Worthey, J.A., and Howett, G.L. Safety Color Appearance Under Selected Light Sources, NBSIR 86-3493, December 1986.

14. Howett, Gerald L., Size of Letters Required for Visibility as a Function of Viewing Distance and Observer Visual Acuity, National Bureau of Standards, 1983.

§



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

39

Revisions 2011

The ANSI Accredited Standards Committee Z535 plans to issue the next revisions of the Z535 Standards (.1 through .5) in December 2011. In order to meet that deadline, the committee developed the following tentative timetable: All proposed changes are due: June 30, 2009 Revisions will be finalized for letter balloting: April 11, 2010 Letter balloting will be completed by: July 18, 2010 Public reviews will be completed by: March 1, 2011 Drafts will be ready to submit to the publisher: May 21, 2011 Published: December 15, 2011 All proposed changes must be submitted by June 30, 2009. Any proposals received after that date will be deferred to subsequent revisions. In order to facilitate the next revision, proposed changes must be submitted on a form for that specific purpose, which is on the back of this page. Please send this form to: Secretary, ANSI Committee Z535 National Electrical Manufacturers Association 1300 North 17th Street, Suite 1752 Rosslyn, VA 22209



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ANSI Z535.2-2007

40

ANSI Accredited Standards Committee Z535 On Safety Signs and Colors

F O R M F O R P R O P O S A L S

Return to: Secretary, ANSI ASC Z535 National Electrical Manufacturers Association 1300 North 17th Street, Suite 1752 Rosslyn, VA 22209 Date________ Name_______________________________ Telephone #_______________________ Address____________________________________________________________________________ Representing________________________________________________________________________

(Please indicate organization or self.) 1. a. Standard Title______________________________________________ b. Section/Paragraph__________________________________________ 2. Proposal recommends (check one): New Text Revised Text Deleted Text 3. Proposal (Include the proposed new or revised text, or identify the words to be deleted.) 4. Statement of the Problem or Substantiation for the Proposal 5. Check one. This proposal is original material. This proposal is not original material; its source is as follows: _______________________________________________________ _______________________________________________________ (This original material is the submitter’s own idea based upon his/her own experience, thought, or research, and to the best of his/her knowledge, is not copied from another source.) I agree to give NEMA all and full rights, including rights of copyright, in this proposal, and I understand that I acquire no rights in any standards publication in which this proposal in this or another similar or analogous form is used. __________________________________________________________________________ Signature Please do not write in the space below. Date Received

Log #



--`,,`,````,,`,`,`,,,,,``,,,,``-`-`,,`,,`,`,,`---

ansi-z535-2-2002-safey-signs[1]

Documents