analysis and design of analog integrated...
TRANSCRIPT
![Page 1: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/1.jpg)
1
Device-Level Noise Modeling(excerpts from Gray & Meyer text
Analysis and Design ofAnalog Integrated Circuits,
John Wiley)
![Page 2: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/2.jpg)
2
(ignore both of these)
“sho
t”
nois
e“Johnson”
noise
![Page 3: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/3.jpg)
3
Comments:•Voltage source representation is used for Series-connectedresistors•Current source representation is used for Parallel-connectedresistors…(discussion in class!)
![Page 4: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/4.jpg)
4
Z(frequency)
basically, input τRC of the circuit
Red=JohnsonBlue=Shot
Let’s look at just ONE TERM…
Basic gain expression (SQUARED)
Voltage divider expression at the input (SQUARED)
Johnson Noise for two resistorsin series (per unit BW)
Transfer Function for Johnson Noise
|Z|
RS rb
![Page 5: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/5.jpg)
5
Additional Noise Sources:•Bias Resistors (parallel)•Shunt-Shunt RF (parallel)
R1||R2 RFRF
Analysis: One needs to determine the transfer function for each noise source to the output and then SQUARE it in order to get the respective POWER relationship…
Typical numbers…IC, lowR’s, a bit high…
dominant term…IC and not resistors
If IC increases 10X,becomes 8.8x10-15
dominant term…resistors, not IB
![Page 6: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/6.jpg)
6
Determined by BW!
![Page 7: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/7.jpg)
7
Gain Expression (Transfer Function) SQUARED
![Page 8: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/8.jpg)
8
RS-eq+rb
R2eq
R2eq Req
Req
Rough Approximation of Open-Loop LNA (Shunt-Shunt Feedback):At output--Req=RL||RFAt input--make ONE equivalent noise resistor (RS-eq) that is in series with rbThe “transfer function” used to refer output noise to the input DOES NOT CHANGE…basically the parallel resistors (R1||R2||RF) are basically now part of new “ ”
Modified(per above discussion)
Z*
Z*
Z*
(see above comment about SQUARED)
![Page 9: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/9.jpg)
9
![Page 10: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/10.jpg)
10
Mission Possible (in 1hr. +??)
1.5KΩand…(in your real design you’ll need to add C)
MI
MO
TL
50Ω −j122Ω(series connected)
SPAMReceiver
(a reminder that Mid-Term will ask you to do “Mission Possible” In-Class and in finite time)
RL_parallelL Cparallel
MI
50Ω −j122Ω
1.5KΩ
L
9V
CBIG
C
70K
Ω20
K Ω
140
Ω
(2V)
(1.4Vdc)
TL
MO
Q1 Equivalent Tank
MI
vs
AntennaLNA (equiv.)
Des
ign!
!
![Page 11: Analysis and Design of Analog Integrated Circuitsweb.stanford.edu/class/ee133/handouts/lecturenotes/lecture8_noise.pdf · 1 Device-Level Noise Modeling (excerpts from Gray & Meyer](https://reader033.vdocuments.mx/reader033/viewer/2022052917/5ad667527f8b9a5c638e4d04/html5/thumbnails/11.jpg)
11
Blocks for SPAM Receiver
BNC toANT
XO
LNAMixer
(SA 612)
IF Amp PLL(LM 565)
BNC toSpeaker
Antenna
Decoding
Lab 1
Lab 2
Lab 4
Lab 3