the following demo demonstrates features and benefits of the fasfold cnc controller when

The following demo demonstrates features and benefits of the Fasfold CNC controller when

retrofitted to a new or used Slitter Folder

It uses a 15 “color touch screen which makes it lightning fast to alter or enter things.

There are 43 slidesUse the left mouse click to go to the next slide.

Use the Backspace key to go to the previous slide.You can also run the actual program from your desktop.

It can control from 2 to 4 axis. It can utilize AC or DC servo control

Whenever you press on any value….

This keypad pops up which allows you to enter data

Finger touch Quickdraw to go to the Quickdraw screen

Touch here to start the profile

Touch here for end of 1st length

Touch here for next bendTouch here to change the grid size

Touch here for next bend

Touch here for last bendLets say we placed it on

the wrong corner. Use the Undo button to erase.

Undo

Undo erased the last bend

Touch here to place the last bend correctly

Use Draw/Edit to make changes

Touch this corner to move it in

Touch this corner to move it in

Touch this corner to move it o

ut again

Use OK to return to The Main Screen

Any values can be altered here to fine tune the profile

Dimensions in the first and Angle in the second column

Use Insert to insert a slit before a bend

Enter the bend number where the slit needs to be inserted

1

This is the Backgauge position For the slit based on the total of all the dimensions of the profileIt can be altered if needed. It is

calculated automatically. Press OK.

This is the total length of the profile above

28.2 plus..

90 plus..

50 plus..

14.2 = 182.4

182.4 for the first slit

The (- blue) for fold 2 & 3 indicates the folds is

done on the bottom side of the material

The ( -) Blue in the first column indicates the fold

needs to be done from the rear of the material

Use sequence to select a specific folding order

other than 1234

Next is 4 then 3 for the next 2 folds

First press 1 for the slit

Lastly press 2 for the last fold

You have now selected a 231 sequence

( if the slit is ignored)

By pressing on any fold number below

Simulate any fold…

This fold needs to be Done from the rear…

So this needs to change to minus 28.2

Now the profile sits on the outside rather than the inside

Use this key to change Between 1 & 2 operators

Use this key to change Between 1 & 2 operators

Use this key to enter a job number

With alphanumeric characters

Use this key to save the job

Enter the password

And press OK

Use this key to open a new job

Press Yes

Touch on the Job you want

Or press UP & Down to scroll to another page

The job opens with all relevant data like which folds is done from the rear or bottom etc

Also the previous fold sequence..Saves a lot of time.

Fold 1 needs to be changed to (-) in the first column

So the material sits outside the folder

Use this to Toggle Between Auto & Manual mode

Use this to Toggle Between Auto & Manual mode

This will take you to the Calibrate& Setup screen

When any input switches or outputs activated, they change between green and red.

It is so quick and powerful to do diagnostics.When you press the footswitch, it changes to green and if the valve operates, it changes

color as well. This minimizes down time.

Valves

Valves

Foot switches

Backgauge motor

Hydrau

lic pump

Encod

er

Top switch

Bottom switch This takes you to the Parameter screen

This is the Backgauge slow speed, fast speed,

Tolerance etc.

This is the Apron slow speed, fast speed,

Tolerance etc.

This takes you to the Calibration

Calibration is as easy as entering the actual measured

values in here.

This takes you backTo the Main screen

This button downloads the job to the PLC on the machine

Jobs can also be downloaded from the office