operation bj t

• Current flow• DC gain

• Voltages in transistor circuits• I-V Characteristics curves

• Load line

Operation of Common Emitter Amplifiers

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

vin

IB

IC

IE

VCC

VCE

VBE

RB

RC

Current flowHOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Common Emitter Amplifier Circuit

• There are three different currents in transistors : collector current IC, base current IB and emitter current IE.

• Since the emitter is the source of the electrons, it has the largest of the three currents.

• The collector current is slightly lower than the emitter current, while the base current is usually very small.

• The relationship is expressed as follows:

IE = IB + IC

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Current flow

• The relationship between the collector current and the base current is expressed in the following formula

• β = IC / IB

• Current gain(HFE)• The ratio between collector current and emitter current

is referred as α (alpha) and is shown in the following relationship :

• α = IC/IE

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

DC Gain

• Emitter voltage,VE

• Base voltage,VB

• Collector voltage,VC

• Collector emitter voltage,VCE

• Base emitter voltage,VBE

• Collector Base voltage,VCB

• DC supply voltage,VCC

VCCVCE

VBEVC

VB

VE

RB

RC

B

C

E

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Voltages in transistor circuits

I - V characteristics are used to explain the operation of transistors.

Output I-V characteristics curvesInput I-V characteristics

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

I-V Characteristics

• A load line is a line drawn over the collector curves to show each and every possible operating point of a transistor.

Load line

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Load Line

saturation

active region

Cut-off

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Operating region of transistors

Transistor can be in either saturation, cut-off or active state.

• It represents normal operation for transistors and graphically, the active region is the middle part of the load line.

• The emitter base junction is forward biased and the collector base junction is reversed biased. • The collector is gathering all the electrons into the base. As such, changes in the collector voltage will have no effect on the emitter current.

P

N

N

IB

IC

IE

VCC > VBE

VBE

VCC

C

B

E

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Active Region

• The collector current reaches its maximum value and will not change even though the base current increases.

• The value for collector emitter voltage is almost zero. The base emitter junction is forward biased and the collector base junction is reversed biased.

• Transistors must operate in this region to function as a close switch.

N

N

P

IB

IC(sat)

IE

VCC < VBE

VBB= VBE

C

BVCC

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Saturation Region

• The value of collector current is almost zero and the value of collector emitter voltage equates the value of DC voltage supply,VCC.

• Both base emitter junction and collector base junction are reversed biased.The widening depletion region will not allow current to flow from the collector to the emitter.

• IC becomes zero and transistors will then function as an open switch.

N

N

P

IB = 0

IC = 0

IE = 0

VBB

VCC

C

B

HOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Cut off Region

• The point at which the base current intersects the load line is referred to as the operating point or the quiescent point.

QHOME

FORWARD

BACK

LASTSLIDE

FIRSTSLIDE

Q point