machine setup. this webinar is listen only questions will be answered in writing at the end of the...

Machine Setup

• This Webinar is LISTEN only

Questions will be answered in writing at the end of the

Webinar.

QUESTIONS?

Webinar Information

Objectives of this lesson:

• Review all the screens and steps required to properly configure your Grader or Dozer.

Machine Setup (Machine Builder)

Machine Setup

Machine Files

Configuration Name/Type

Machine Type

Sensor Type

Mounting Location Grader

Mounting Location Dozer

Units of Measure

Motorgrader w/GPS

Motorgrader Antenna Selection

Topcon Twin (MC-A2) will require additional calibration not covered in this Webinar

Motorgrader Antenna Selection

CR-3

Rev 1MC-A2 & MC-A1

Measurements

When making all the measurements for a Grader or Dozer use + numbers unless the measurement is opposite of what's being asked.

Motorgrader Above

Above MeasurementSlant heightFront Antenna Rim

Motorgrader Above

Above MeasurementSlant heightFront Antenna Rim

Motorgrader Inside

Inside MeasurementVertical Pole (side to side)Offset from center of Pole

Motorgrader Inside

Inside MeasurementVertical Pole (side to side)Offset from center of Pole

Motorgrader Behind

Behind MeasurementVertical Pole (front to back)Offset from center of Pole

Motorgrader Behind

Behind MeasurementVertical Pole (front to back)Offset from center of Pole

Error!

Motorgrader Behind

Behind MeasurementVertical PoleOffset from center of Pole

Motorgrader Width

Width MeasurementBlade length (width)

Motorgrader Width

Width MeasurementEnd to End

Next

GPS Precisions

GPS PrecisionsPosition Quality RTKMax. GPS errors (roving)

•GPS status will flash orange if RMS values are exceededMax. GPS errors (point measurement)

•Tolerance for topo survey and measure point feature

GPS Comms Configuration

GPS Cooms ConfigurationSetup screen for GPS receiver

GPS Comms Configuration

ConnectionSerial Port MC 2.5TCP/IP 9905 & 9906 MC-R3 with 160 BoardsUDP/IP 9907 & 9908 MC-R3 112 Boards (3D-MC2 all MC-R3 since mid Feb)

MC 2.5

MC-R3

GPS Comms Configuration

IP Address/Port/PasswordSettings programmed on the GNSS receiver

•All boxes use the same settings the default button sets defaults

MC 2.5

9907 & 9908 112 boards

9905 & 9906 160 boards

GPS Radio Configuration

Used to configure radio type also accessed in the Tools menu

LD-40 Setup

LD-40 Setup

Search finds all attached LD-40 light bars and will populate the ID boxSelect an LD-40 from the ID pull downWith the LD-40 selected the Identify button will cause all the lights flash

LD-40 Setup

LocationSelect how the LD-40 is to be used

•Left edge (position information for the left edge to the design surface)•Right edge (position information for the right edge to the design surface)•Cut/Fill (will be the point you select on the blade in the blade control menu)•Slope (the difference from actual slope to design slope matches 9168 LEDs)•Steering (LD-40 being used as a steering indicator)

LD-40 Setup

CenteredIf checked the On-Grade will be positioned in the center of the LD-40If unchecked the On-Grade will be positioned on the lower half of the LD-40

•Typical application for Excavators or scrapers making large cuts working down to grade

LD-40 Setup

InvertedThe Inverted option selects the correct orientation of the LD-40

LD-40 Setup

PrecisionsSet the sensitivity of the LD-40 LEDs.

1 Fine - 5 Coarse

1=15mm (per LED)2=20mm (per LED)3=30mm (per LED)4=50mm (per LED)5=100mm (per LED)

LD-40 Setup

ColorsChanges the Cut/Fill colors.

•Yellow over Red•Red over Blue

LD-40 Setup

Auto/2DThe operator can select to have the LED on the Left or Right LD-40 illuminate when the machine is in auto. The Auto Left/Right selection is for 3D mode. The 2D Left/Right selection is for 2D mode. When operating a Grader both the Right and Left Auto switches need to be in auto for the LED to illuminate.

Dozer Configuration

Dozer Sensor Selection

Select the appropriate sensor

Dozer System 5

System 5 sensor MC Builder

Dozer System 5

Ensure the Antenna is perpendicular to the tracks on level ground when making machine measurements.

Dozer Above

Above Measurement

Dozer System 5

Above MeasurementSlant heightFront Antenna Rim

Dozer Inside

Dozer Inside

Ensure the antenna is vertical

Dozer Inside

Ensure the antenna is verticalDrop plum bob from center of the vibration poleMeasure from the Right side of the blade

Dozer Behind

Dozer Behind

Dozer Behind MeasurementDrop plum bob from center of the vibration poleMeasure distance behind

Dozer Width

Dozer Width

Dozer Width MeasurementMeasure blade width

Remaining Screens

The remaining screens are the same as previously explained.

Slope Sensor 3DMC2

When configuring a 3DMC2 Dozer one additional measurement screen is available.

Slope Sensor 3DMC2

When configuring a 3DMC2 Dozer one additional measurement screen is available. For details on configuring a 3DMC2 Dozer refer to the 3D-MC2 Setup & Calibration Webinar posted on the TU Website. http://www.topconuniversity.com/

Questions?

• Address to download all TU-Live Webinars:

http://www.topconuniversity.com/

• Additional requests for TU staff:

Email: training@topcon.com